HP 3C905B-TX User Manual

HP 10/100 3Com 3C905B-TX

Network Interface Card

Installation Guide

Network Interface Card

Installationsanleitung

Guide d’installation de la carte

d’interface réseau

Guía de Instalación de la Tarjeta

de Interfaz de Red

Léase esto primero

Guida di installazione

della scheda di interfaccia di rete

English . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 1

Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . Kapitel 2

Français. . . . . . . . . . . . . . . . . . . . . . . . . . . Chapitre 3

Español . . . . . . . . . . . . . . . . . . . . . . . . . . . Capítulo 4

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . Capitolo 5

English

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Notice

The information contained in this document in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company.

Acrobat

and Adobe® are trademarks of Adobe Systems Incorporated and may

be registered in certain jurisdictions.

3Com Magic Packet Microsoft

and EtherDisk® are U.S. registered trademarks of 3Com Corporation.

and PCnetTM are U.S. trademarks of AMD Corporation.

, Windows®, and Windows NT® are U.S. registered trademarks of

Microsoft Corporation.

Hewlett-Packard France Commercial Computing Division Technical Marketing 5 Avenue Raymond Chanas 38053 Grenoble Cedex 9 France

1998 Hewlett-Packard Company

Excerpted material reprinted with permission from 3Com Corporation.

1998 3Com Corporation

2 English

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

What’s in the Network Kit?

The Network Kit includes the following items:

Quantity in Network Kit

Component

D6500A D6509A

What’s in the Network Kit?

HP 10/100 3Com 3C905B-TX network interface card (NIC)

LAN driver diskettes 2 2

Wake 0n LAN cable 1 10

This Installation Guide 11

110

Installation Requirements

The following operating systems and HP PC platforms are supported for installation of the network interface card.

Supported Operating Systems

Windows 95 SR2 or later

•

Windows NT 4.0 and Service Pack 3

•

The driver installation diskettes contain drivers for other network operating systems. For more information on installing these drivers, refer to the readme files provided on the installation diskettes. The latest drivers are available on HP’s Web site at:

http://www.hp.com/go/vectrasupport

English 3

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Installation Requirements

Supported Platforms

To find out on which PCs you can install a 3C905B-TX card, go to the following HP Web sites:

For Vectra Corporate PCs

•

http://www.hp.com.go/vectraaccessories

For Kayak PC workstations

•

http://www.hp.com.go/kayakaccessories

NT Service Pack

If an NT service pack is already installed on the PC, it must be re-installed after the Network Interface Card (NIC) and software is installed. When using the HP preloaded NT 4.0 software, the latest service pack can be found in the C:\I386\SP

directory.

Operating System Master Diskettes

During the software installation you will need to have your operating system master diskettes or CD-ROM available.

When using HP preloaded operating system software, the master diskettes can be found in the following directories:

C:\I386 (Windows NT 4.0)

•

C:\WINDOWS\OPTIONS\CABS (Windows 95)

•

4 English

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Installation Requirements

Supported Network Drivers

The following network drivers are supported by Hewlett-Packard:

Network Operating

System

Windows 95 W95NDIS.TXT EL90XND3.SYS

Windows 95 NDIS 2 W95NDIS.TXT EL90X.DOS

Windows NT 3.51 WINNT.TXT EL90XND3.SYS

Windows NT 4.0 WINNT.TXT EL90XND4.SYS

NetWare Client 32 ODI CLIENT32.TXT 3C90X.LAN

NetWare OS/2 NWOS2ODI.TXT 3C90X.SYS

NetWare client for DOS, Windows 3.1, and Windows for Workgroups

Windows for Workgroups (NetWare)

Windows for Workgroups (NDIS 2)

Windows for Workgroups (NDIS 3)

AUTOLINK.TXT (NETWARE directory)

WFWNETWR.TXT 3C90X.COM

WFWNDIS2.TXT EL90X.DOS

WFWNDIS3.TXT EL90X.386

README

(for driver installation)

Network Driver Name

EL90XND4.SYS

3C90X.COM

Microsoft LAN Manager LANMAN.TXT EL90X.DOS

English 5

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Overview of the Installation Procedure

Non-Supported Network Drivers

The following network drivers are provided on the

EtherDisk

diskettes

but not supported by Hewlett-Packard:

Network Operating

System

Netware 4.1 Server NETWARE.41X 3C90X.LAN

Banyan VINES BANYAN.TXT EL90X.DOS

Artisoft LANtastic LANTASTK.TXT EL90X.DOS

IBM LAN SERVER (DOS) LANSRVR.TXT EL90X.DOS

IBM LAN SERVER (OS/2) LANSRVR.TXT EL90X.OS2

DEC PATHWORKS PATHWORK.TXT EL90X.DOS (DOS) and

README (for driver

installation)

Network Driver Name

3C90X.COM (Netware)

Overview of the Installation Procedure

CAUTION Your PC and network interface card can be permanently damaged by

static electricity. Before handling the card, touch the unpainted part of your PC’s metal chassis. Maintain grounding by wearing a wrist strap attached to the chassis. Handle the card by its backplate and top edge. Do not touch the edge connector.

Installing the 3C905B-TX NIC is a 4-step process. You need to:

Install the card in your PC.

Connect the card to the network.

Update LAN-specific fields in the HP PC Setup utility.

Install the driver software.

6 English

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Installing the Network Interface Card

For complete information on how to install an accessory card, refer to your PC User’s Guide. The following steps are given as a guide.

With the PC turned off, disconnect the power cord and any

connection to a telecommunications network, and then remove the cover.

Choose an empty PCI slot. If you do not know how to identify a PCI

slot, refer to your PC’s documentation.

Remove the metal slot cover.

Depending on the PC model, you may need to remove the accessory

slot’s retaining bracket. Refer to your PC User’s Guide if necessary.

Insert the card into the accessory slot without bending it.

The card may be installed in a minitower model or in a desktop model.

Connect the Wake on LAN cable to the connectors on the NIC and

the backplane or motherboard. For the position of the Wake on LAN connector on the NIC, refer to “3C905B-TX NIC Specifications” on page 16. Refer to your PC’s documentation for the position of the Wake on LAN connector on the system board or backplane.

Secure the card by replacing the slot cover screw or the retaining

bracket and its screw, as appropriate.

Replace the cover. Reconnect the power cord and any connection to

a telecommunications network.

English 7

RJ-45 UTP Connector

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Connecting to the Network

Connect the network cable to the RJ-45 UTP (Unshielded Twisted Pair) LAN connector. The LAN card supports both 10 Mbits/s and 100 Mbits/s operation.

Remote Wake Up

The network interface card is able to wake the PC from a sleep state if it receives a special sequence (known as a Magic Packet network.

8 English

) from the

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Updating LAN-specific Fields in the HP PC Setup Utility

Having physically installed the network interface card in the PC, you now need to check that the BIOS is configured to use the card. To do this you need to use the HP PC Setup utility.

Starting the HP PC Setup Utility

Restart the PC.

Press when

F2=Setup

is displayed on the screen during the PC’s startup routine. The opening window of the HP PC Setup utility is displayed.

Which Fields Need Updating?

You need to check, and update if necessary, all the fields that are LAN-related.

The bulleted list given below gives guidelines on how to configure a LAN interface. The field names used in your version of the Setup program may be slightly different to those shown below.

If you want to boot from the network:

Check that

•

Change the boot order so that Network appears first (

•

Advanced CMOS Setup

Security

➜

Boot Devices Security

➜

1st Boot Device‹ Network

➜

Start from Network

is enabled.

Advanced

➜

NOTE You can only boot a PC from the network if it has boot ROM integrated

in its BIOS (as with the HP Vectra VL Series 8 PC for example) or if it contains an NIC with an embedded boot ROM chip.

On other platforms such as the HP Vectra VL Series 7, VE Series 7 or Series 8 PCs, a boot ROM chip is needed in order to boot from the network. This component can be ordered from 3Com.

If you want to wake up your PC from the network:

Check that the PC can be woken up from the network (

•

Suspend Wakeup

➜

Network [Enabled

]).

Power

➜

If you want to power on your PC from the network:

Check that the PC can be powered on from the network (

•

Power-On

English 9

➜

Network [Enabled

]).

Power

➜

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Software Installation Procedure

CAUTION Make sure that you have installed the network interface card before you

install the network driver software.

Software Installation on a Windows 95 System

This section describes how to install the network driver when your PC is running Windows 95:

Start the PC.

Windows 95 will automatically detect the network interface card.

Select

from the disk provided by the hardware manufacturer

Driver

and click on OK.

Insert EtherDisk diskette #2 in your drive, and if the diskette is in

drive A, click on OK. Otherwise, supply the correct drive letter and then click on OK. Once the 3Com installation files have been read, Windows 95 prompts you for the Windows 95 network installation files.

Enter the location of the Windows 95 files (CAB files), and click on

OK. On HP Windows 95 preloaded systems, the path is C:\WINDOWS\OPTIONS\CABS. If Windows prompts you to reboot, click on Yes. The driver installation is complete.

Confirming Installation

Follow these steps to confirm that the network interface card is properly installed in a PC running Windows 95:

Double-click on the

My Computer

Control Panel

System

icon.

icon. The

System Properties

box appears.

Click on the

Device Manager

tab. A list of devices appears, arranged by

type.

10 English

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Software Installation Procedure

5 Double-click on

Network Adapters

. The name of the installed network

interface card appears: 3Com EtherLink XL Adapter (3C905B). If this name does not appear or if a yellow exclamation mark appears next to it, follow this troubleshooting procedure:

a In the

Device Manager

window, double-click on

Other Devices

b Click PCI Ethernet Controller or the duplicate

3C905B-TX NIC entry.

c Click on

Remove

d Restart your PC.

Software Installation and Update on a Windows NT 4.0 System

This section describes how to install the network driver in a PC workstation running Windows NT version 4.0. Before you begin, obtain EtherDisk diskette #2 and Windows NT installation files (stored under

C:\I386

If Windows NT networking is not installed, you may also need the following information from your MIS department:

•

on systems preloaded with Windows NT 4.0).

Whether you are on a LAN or are connecting to one through a modem

The protocol used in the Microsoft Windows Network (typically TCP/IP or NetBEUI)

The name of the Windows NT server domain or workgroup you belong to

Your IP address if you are not using DHCP

English 11

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Software Installation Procedure

Installing the Driver

Follow these steps to install the network driver in a PC running Windows NT version 4.0:

1 Restart the PC and start Windows NT. 2 In the 3 In the 4 In the

Control Panel

Network

Select Network Component Type

and then click on the

5 In the

Select Network adapters

6 Insert EtherDisk diskette #2 in drive A, and in the

, double-click on

window, click on the

window, select the Adapter item

button.

Add...

window, click on the

Network

Add...

button.

Have Disk...

Insert Disk

button.

window,

click on OK.

7 In the Select OEM Option box, select 3Com EtherLink Adapter

(3C905B).

8 Click on OK. 9 Select the

Protocol

tab.

10 Select the appropriate protocol for your network and click on OK. 11 Close the

Network

window. If you are prompted for network information, enter the information supplied by your MIS department. Windows NT prompts you to reboot.

12 Click on Yes to restart your PC.

The driver installation is complete. To confirm successful installation, double-click on the the

Control Panel

. Double click on the Adapter item. 3Com

Network

icon in

EtherLink XL Adapter should appear in the Network Adapters list.

12 English

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Checking the Installation

CAUTION If a service pack was already installed on the PC before the network

interface card was installed, the service pack must be reinstalled.

On some platforms you also need to reinstall your video drivers. Check your PC documentation for more information.

Updating the Driver

If you already have the 3C905B-TX network driver and want to update it, follow the instructions provided below.

1 Install the network interface card and connect it to the network as

described earlier.

2 Restart the PC and start Windows NT. 3 In the 4 In the

Control Panel

Network

, double-click on

Network

window, double-click on the Adapter item.

5 Select 3Com EtherLink XL NIC. 6 Click on Update. 7 Insert EtherDisk diskette #2. The driver will be automatically

updated.

CAUTION If a service pack was already installed on the PC before the network

interface card was installed, the service pack must be re-installed.

On some platforms you also need to reinstall your video drivers. Check your PC documentation for more information.

Checking the Installation

Test whether the card functions on the network by finding another network device or performing a network operation. If it does not work correctly, refer to the “Troubleshooting” section that follows.

English 13

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Troubleshooting

The 3C905B-TX Card Does Not Work

If your network interface does not work, try the following:

Check that:

•

The card is correctly installed (refer to “Installing the Network

•

Interface Card” on page 7).

The LAN-specific fields in the HP PC Setup utility are correctly

•

set (refer to “Updating LAN-specific Fields in the HP PC Setup Utility” on page 9).

The software installation steps have been followed (refer to

•

“Software Installation Procedure” on page 10).

Check the network cables. In particular, check that the network

•

cable connections are secure and that the cables are not damaged. If you find any loose connections or damaged cables, fix them and then see if your PC can communicate on the network.

Check that either the 10 LNK or 100LNK green LED on the

•

3C905B-TX NIC’s rear panel is on (refer to “3C905B-TX NIC Specifications” on page 16). The green LED on the card’s rear panel is off when there is no network link, for example, when the LAN cable is not connected to the network HUB.

For NT 4.0 systems, check that your Service Pack has been

•

reinstalled. In case of doubt, reinstall the Service Pack.

14 English

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

HP Support Services

The PC Cannot Be Started or Woken up from the Network

Check that the WOL connector cable is connected to the network interface card and to the PC’s system board.

If the PC has been powered off (for example, due to an electrical

•

power failure, or because the power cord has been removed), the Remote Power On (RPO) will not work. To enable the RPO, you must first power on the PC, allow Windows 95 or NT 4.0 to boot, then shut down the PC.

Check that the WOL connector cable is connected to the network

•

interface card and to the PC’s system board.

Check that the LAN-specific fields in the HP PC Setup utility are

•

correctly set (refer to refer to “Updating LAN-specific Fields in the HP PC Setup Utility” on page 9).

NOTE RPO is only supported under Windows 95 and Windows NT 4.0.

HP Support Services

The latest drivers and utilities are available on HP’s Web site at:

http://www.hp.com/go/vectrasupport

English 15

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

3C905B-TX NIC Specifications

Physical Layout

LAN Connector

Wake on LAN (WOL) Connector

ACT LED 10 LNK LED 100 LNK LED

Refer to “LAN Connection Status LEDs” on page 17 for more information

Specifications

Network Interface

Physical Dimensions

Environmental Operating Range

DATA

ACT

100

10 Mbps Ethernet 10BASE-T: Ethernet IEEE 802.3 industry standard

•

for a 10 Mbps baseband CSMA/CD local area network. 100 Mbps Ethernet 100BASE-TX: Ethernet IEEE 802.3u industry

•

standard for a 100 Mbps baseband CSMA/CD local area network.

Height: 8.57 cm (3.75 in.)

•

Length: 12.07 cm (4.75 in.)

•

Operating temperature: 0° to 70° C (32° to 158° F)

•

Humidity: 10 to 90% noncondensing

•

16 English

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

3C905B-TX NIC Specifications

Power Requirements

Operating voltage: +5 V ± 5% @650 mA max

•

LAN Connection Status LEDs

There are three LEDs on the rear of the 3C905B-TX NIC that indicate the LAN connection status as follows:

LED Description Flashing Steady Off

10 LNK Green:

Link integrity

100 LNK Green:

Link integrity

ACT Yellow:

Port traffic for either speed

Reversed polarity Good 10BASE-T

connection between NIC and hub

Reversed polarity Good

100BASE-TX connection between NIC and hub

Network traffic present

Heavy network traffic

No connection between NIC and hub

No traffic

English 17

Regulatory Information

DECLARATION OF CONFORMITY

According to ISO/IEC Guide 22 and EN 45014

Manufacturer’s Name: HEWLETT-PACKARD Manufacturer’s Address: 5 Avenue Raymond Chanas

Declares that the product: Product Name: HP 10/100 3Com 3C905B-TX Network Interface Card

Conforms to the following Product Specifications:

Supplementary information:

The EMC directive 89/336/EEC amended by the directive 93/68/EEC. The Low Voltage Directive 73/23/EEC.

The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems.

This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Grenoble Jean-Marc JULIA May 1998 Quality Manager

38053 Grenoble Cedex 09 FRANCE

Model Number: D6500A & D6509A

SAFETY

EMC

The product herewith complies with the requirements of the following Directives and carries the CE-marking accordingly:

International: IEC 950:1991 +A1 +A2 +A3+A4 Europe: EN 60950:1992 +A1 +A2 +A3

CISPR 22:1993+A1 / EN 55022:1994 Class B EN 50082-1:1992

IEC 801-2:1992 / prEN 55024-2:1992 - 4kV CD, 8kV AD IEC 801-3:1984 / prEN 55024-3:1991 - 3V/m IEC 801-4:1988 / prEN 55024-4:1992 - 0.5 kV Signal Lines,

IEC 555-2:1982+A1:1985 / EN60555-2:1987

IEC 1000-3-3:1994 / EN61000-3-3:1995

FCC Title 47 CFR, Part 15 Class B

AS / NZ 3548:1992

1 kV Power Lines

/ ICES-003, Issue 2 / VCCI-2 1)

For Compliance Information ONLY, contact: Hewlett-Packard Company, Corporate Product Regulations Manager, 3000 Hanover Street, Palo Alto, CA 94304. (Phone: (415) 857-1501)

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Hardware Warranty

FCC (for USA only)

Federal Communications Commission Radio Frequency Interference Statement

Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures:

• reorient or relocate the receiving antenna

• increase the separation between the equipment and the receiver

• connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• consult the dealer or an experienced radio/TV technician for help. Hewlett-Packard’s FCC Compliance Tests were conducted with HP-supported peripheral devices and HP

shielded cables, such as those you receive with your system. Changes or modifications not expressly approved by Hewlett-Packard could void the user’s authority to operate the equipment.

Notice for Canada

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la Class B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Hardware Warranty

This HP accessory is covered by a limited hardware warranty for a period of one year from the date of purchase by the original end-user. The type of service provided is return to an HP or repair-authorized reseller service-center.

At Hewlett-Packard's discretion, a defective accessory will be repaired or replaced by a new unit, either of the same type or of an equivalent model.

If this accessory is purchased and used together with an HP Vectra personal computer, it will be covered by the warranty of this computer or workstation, under the same conditions of service and duration.

Please, refer to the warranty statement provided with your HP personal computer or PC workstation for warranty limitations, customer responsibilities and other terms and conditions.

FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND: THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT LAWFULLY PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.

English 19

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

Hardware Warranty

20 English

HP 10/100 3Com 3C905B-TX Network Interface Card Installationsanleitung

HP 10/100 3Com 3C905B-TX Network Interface Card Installationsleitung

Hinweis

Die in diesem Dokument enthaltenen Informationen können ohne vorherige Ankündigung geändert werden.

Hewlett-Packard gewährt keinerlei Garantie auf dieses Material und schließt unter anderem Vermarktungsgarantien und Gewährleistung der Eignung des Materials für einen bestimmten Zweck aus. Hewlett-Packard ist für in diesem Material auftretende Fehler sowie für zufällige oder kausale Fehler in Zusammenhang mit der Lieferung, Leistung oder Anwendung dieses Materials nicht haftbar zu machen.

Hewlett-Packard übernimmt keine Verantwortung für die Verwendung oder Zuverlässigkeit seiner Software, die auf Geräten betrieben wird, die nicht von Hewlett-Packard geliefert wurden.

Dieses Dokument enthält eigentumsrechtliche Informationen, die durch das Urheberrecht geschützt sind. Alle Rechte sind vorbehalten. Ohne die vorherige, schriftliche Einverständniserklärung der Hewlett-Packard Company darf kein Teil dieses Dokuments fotokopiert, reproduziert oder in eine andere Sprache übersetzt werden.

Acrobat und können in bestimmten Ländern eingetragen sein.

3Com 3Com Corporation.

Magic Packet Microsoft

Handelsmarken der Microsoft Corporation.

und Adobe® sind Handelsmarken der Adobe Systems Incorporated

und EtherDisk® sind in den USA eingetragene Handelsmarken der

und PCnetTM sind US-Handelsmarken der AMD Corporation.

, Windows® und Windows NT® sind in den USA eingetragene

Hewlett-Packard France Commercial Computing Division Technical Marketing 5 Avenue Raymond Chanas 38053 Grenoble Cedex 9 Frankreich

 1998 Hewlett-Packard Company

Es wird auszugsweise Material mit Genehmigung der 3Com Corporation reproduziert.

 1998 3Com Corporation

2Deutsch

HP 10/100 3Com 3C905B-TX Network Interface Card Installationsleitung

Was enthält das Network Kit?

Das Network Kit umfaßt die folgenden Komponenten:

Anzahl im Network Kit

Komponente

D6500A D6509A

HP 10/100 3Com 3C905B-TX network interface card (NIC)

LAN Treiberdisketten 2 2

Wake 0n LAN-Kabel 1 10

Diese Installationsanleitung 11

110

Installationsvoraussetzungen

Für die Installation der Network Interface Card werden die folgenden Betriebssysteme und HP PC-Plattformen unterstützt.

Unterstützte Betriebssysteme

Windows 95 SR2 oder höher

•

Windows NT 4.0 und Service Pack 3

•

Die Installationsdisketten der Treiber enthalten Treiber für andere Netzwerk-Betriebssysteme. Weitere Informationen zur Installation dieser Treiber finden Sie in den Readme-Dateien auf den Installationsdiskette. Die neuesten Treiber finden Sie auf der Website von HP unter:

http://www.hp.com/go/vectrasupport

Deutsch 3

HP 10/100 3Com 3C905B-TX Network Interface Card Installationsleitung

Installationsvoraussetzungen

Unterstützte Plattformen

Auf den folgenden HP Websites erfahren Sie, auf welchen PCs Sie eine 3C905B-TX Karte installieren können:

Für Vectra Firmen-PCs

•

http://www.hp.com.go/vectraaccessories

Für Kayak PC workstations

•

http://www.hp.com.go/kayakaccessories

NT Service Pack

Wenn auf dem PC bereits ein NT Service Pack installiert ist, muß es nach der Installation der Network Interface Card (NIC) und der Software nochmals installiert werden. Bei der Verwendung der vorinstallierten HP NT 4.0 Software kann das neueste Service Pack im Verzeichnis C:\I386\SP

gefunden werden.

Betriebssystem-Masterdisketten

Während der Installation der Software müssen Sie Ihre Betriebssystem-Masterdisketten oder die CD-ROM zur Hand haben.

Bei der Verwendung der vorinstallierten HP Betriebssystem-Software können die Masterdisketten in den folgenden Verzeichnissen gefunden werden:

C:\I386 (Windows NT 4.0)

•

C:\WINDOWS\OPTIONS\CABS (Windows 95)

•

4Deutsch

HP 10/100 3Com 3C905B-TX Network Interface Card Installationsleitung

Installationsvoraussetzungen

Unterstützte Netzwerktreiber

Die folgenden Netzwerktreiber werden von Hewlett-Packard unterstützt:

Netzwerk-Betriebssystem

Windows 95 W95NDIS.TXT EL90XND3.SYS

Windows 95 NDIS 2 W95NDIS.TXT EL90X.DOS

Windows NT 3.51 WINNT.TXT EL90XND3.SYS

Windows NT 4.0 WINNT.TXT EL90XND4.SYS

NetWare Client 32 ODI CLIENT32.TXT 3C90X.LAN

NetWare OS/2 NWOS2ODI.TXT 3C90X.SYS

NetWare Client für DOS, Windows 3.1, und Windows für Workgroups

Windows für Workgroups (NetWare)

Windows für Workgroups (NDIS 2)

Windows für Workgroups (NDIS 3)

(für Installation der Treiber)

AUTOLINK.TXT (NETWARE Verzeichnis)

WFWNETWR.TXT 3C90X.COM

WFWNDIS2.TXT EL90X.DOS

WFWNDIS3.TXT EL90X.386

README

Name des Netzwerktreibers

EL90XND4.SYS

3C90X.COM

Microsoft LAN Manager LANMAN.TXT EL90X.DOS

Deutsch 5

HP 10/100 3Com 3C905B-TX Network Interface Card Installationsleitung

Installationsvoraussetzungen

Nicht unterstützte Netzwerktreiber

Die folgenden Netzwerktreiber befinden sich auf den EtherDisk Disketten, werden jedoch nicht von Hewlett-Packard unterstützt:

Netzwerk-Betriebssystem

Netware 4.1 Server NETWARE.41X 3C90X.LAN

Banyan VINES BANYAN.TXT EL90X.DOS

Artisoft LANtastic LANTASTK.TXT EL90X.DOS

IBM LAN SERVER (DOS) LANSRVR.TXT EL90X.DOS

IBM LAN SERVER (OS/2) LANSRVR.TXT EL90X.OS2

DEC PATHWORKS PATHWORK.TXT EL90X.DOS (DOS) und

README (für Installation der

Treiber)

Name des Netzwerktreibers

3C90X.COM (Netware)

6Deutsch

+ 80 hidden pages