HP 100B-TX User Manual

Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Installation Guide
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company.
Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft Corporation.
TM
MMX Pentium® is a registered trademark of Intel Corporation.
is a trademark of Intel Corporation.
Hewlett-Packard France Commercial Desktop Computing Division 38053 Grenoble Cedex 9 France
©1999 Hewlett Packard Company
Microsoft Windows 95 SR2.5
1 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
1 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Windows NT 3.51 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Microsoft Windows NT Server 3.51 system that supports NetBEUI, TCP/ IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 10
I/O Address 1020 DCE0 E400
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-
TX PCI adapter card into an PCI slot.
2 Connect network cable media to the PRO 100B-TX PCI card.
3 Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4 Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “A:\SETUP.EXE”.
5 Select “VIEW ADAPTER SETTINGS” and verify the resource settings
listed above under the heading “Device Configuration”.
6 If changes are required, save those changes and exit.
7 Remove the Intel Software driver diskette and restart the system.
8 When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
1 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Windows NT 3.51 Server
9 When prompted, click on “Next” and then click on “Other Locations” to
provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.
10 Insert the drivers diskette and set the path statement to “A:\” and click on
“OK”.
11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on
“Finish”.
12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and
click on “OK”.
13 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
14 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network administrator).
15 Click on “Close” button, and files will copy.
16 Click on the “Yes” button to finish the installation and restart your
computer.
Microsoft Windows 95 SR2.5
2 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
2 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Windows NT 4.0 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Microsoft Windows NT Server 4.0 system that supports NetBEUI, TCP/IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 10
I/O Address 1020 DCE0 E400
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-
TX PCI adapter card into an PCI slot.
2 Connect network cable media to the PRO 100B-TX PCI card.
3 Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4 Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “A:\SETUP.EXE”.
5 Select “VIEW ADAPTER SETTINGS” and verify the resource settings
listed above under the heading “Device Configuration”.
6 If changes are required, save those changes and exit.
7 Remove the Intel Software driver diskette and restart the system.
8 When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
2 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Windows NT 4.0 Server
9 When prompted, click on “Next” and then click on “Other Locations” to
provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.
10 Insert the drivers diskette and set the path statement to “A:\” and click on
“OK”.
11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on
“Finish”.
12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and
click on “OK”.
13 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
14 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network administrator).
15 Click on “Close” button, and files will copy.
16 Click on the “Yes” button to finish the installation and restart your
computer.
Microsoft Windows 95 SR2.5
3 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
3 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Novell NetWare 3.12 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Novell NetWare 3.12 system that supports NetBEUI, TCP/IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 11
I/O Address 1020 DCE0 E400
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-
TX PCI adapter card into an PCI slot.
2 Connect network cable media to the PRO 100B-TX PCI card.
3 Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4 Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “A:\SETUP.EXE”.
5 Select “VIEW ADAPTER SETTINGS” and verify the resource settings
listed above under the heading “Device Configuration”.
6 If changes are required, save those changes and exit.
7 Remove the Intel Software driver diskette and restart the system.
8 When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
3 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Novell NetWare 3.12 Server
9 When prompted, click on “Next” and then click on “Other Locations” to
provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.
10 Insert the drivers diskette and set the path statement to “A:\” and click on
“OK”.
11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on
“Finish”.
12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and
click on “OK”.
13 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
14 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network administrator).
15 Click on “Close” button, and files will copy.
16 Click on the “Yes” button to finish the installation and restart your
computer.
Microsoft Windows 95 SR2.5
4 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
4 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Novell NetWare 4.11 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Novell NetWare 4.11 system that supports NetBEUI, TCP/IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 10
I/O Address 1020 DCE0 E400
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-
TX PCI adapter card into an PCI slot.
2 Connect network cable media to the PRO 100B-TX PCI card.
3 Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4 Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “A:\SETUP.EXE”.
5 Select “VIEW ADAPTER SETTINGS” and verify the resource settings
listed above under the heading “Device Configuration”.
6 If changes are required, save those changes and exit.
7 Remove the Intel Software driver diskette and restart the system.
8 When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
4 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Novell NetWare 4.11 Server
9 When prompted, click on “Next” and then click on “Other Locations” to
provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.
10 Insert the drivers diskette and set the path statement to “A:\” and click on
“OK”.
11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on
“Finish”.
12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and
click on “OK”.
13 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
14 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network administrator).
15 Click on “Close” button, and files will copy.
16 Click on the “Yes” button to finish the installation and restart your
computer.
Loading...
+ 22 hidden pages