HOTPOINT/ARISTON FTCD 871 6H1 (EU) User Manual

Instruction booklet

TUMBLE DRYER

English, 1

Español, 49

Deutsch, 17

Türkçe, 65

FTCD 871

First time you turn on your dryer you must select your preferred language see Display

Polski, 33

Contents

Installation, 2

Warnings, 4

Care and Maintenance, 6

Control Panel, 8

Laundry, 8

The Display, 9

Start and Programmes, 11

Troubleshooting, 15

Assistance, 16

www.hotpoint.eu

! This symbol reminds you to read this

instruction manual.

! Keep this manual at hand for immediate reference whenever

necessary. Always store this manual close to the tumble dryer and remember to pass it on to any new owners when selling or transferring the appliance, so they may familiarise with the warnings and suggestions herein contained.

! Read these instructions carefully: the following pages contain

important information on installation and useful suggestions for operating the appliance.

Installation

10 mm

15 mm

Where to put your dryer

• Place your dryer at a distance from gas ranges, stoves, heaters, or cooktops because flames can damage the appliance. The dryer should be installed in an ambient room temperature of between 20 to 23°C for optimum performance. But will function if the room is between 14 and 30°C. If you are going to install the appliance under a work counter, be sure to leave a 10 mm space between the top and any other objects on or above the machine and a 15 mm space between the sides and lateral furnishings or walls. This is to ensure proper air circulation.

The appliance must be installed with the rear surface placed against a wall.

Ventilation

• When the dryer is in use, there has to be adequate ventilation. Make sure you put your dryer in an environment that is not damp and has proper air circulation throughout. Airflow around the dryer is essential to condense the water produced during the washing, the dryer will not operate efficiently in an enclosed space or cupboard. ! If using the dryer in a small or cold room some condensation will be experienced.

We do not recommend that the dryer is installed in a cupboard but the dryer must never be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the dryer door.

Fig. A Fig. B

Water Drain

If the machine is positioned close to a drain it is possible to drain the condensed water directly without using the waterbottle. In which case it is no longer necessary to empty the water bottle at the end of each cycle. If the Dryer is positioned above or close to a Washing Machine the same drainage can be used. Just remove the tube indicated in figure A and connect it to the drainage. If the drainage

H<1m

is further away than the length of the tube it is possible to buy and connect a tube of the same diameter and the necessary length in order to reach the drain. To install the new tube just substitute the existing one as indicated in figure B inserting it in the same place.

! The drain tube has to be below 1 m from the bottom of the Dryer. ! Once the Dryer has been installed please assure that the drain tube is not bent or kinked.

Electrical connections

Before plugging the appliance into the socket, check the following:

• Make sure your hands are dry.

• The socket must have an earth connection.

• The socket must be able to withstand the machine’s maximum power output as indicated on the rating plate.

• The power supply voltage must fall within the values indicated on the data plate.

• The socket must be compatible with the dryer’s plug. Should this not be the case, replace the plug or the socket.

! DO NOT USE EXTENSION CORDS. ! The dryer must not be installed outdoors, even if the space is sheltered. It can be very dangerous if exposed to rain or storms. ! Once installed, the dryer’s electrical wire and plug must be within reach. ! The power cord must not be bent or squashed. ! If the plug being replaced is a non-rewirable type, then the cut-off plug must be disposed of safely. DO NOT leave it where it can be inserted into a socket and create a shock hazard.

! The power must be regularly checked. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. (see Assistance). New or longer electric cords are supplied by authorised dealers at a supplementary cost.

! The manufacturer denies any responsibility should any of these rules not be followed. ! If in doubt about any of the above consult a qualified electrician.

Levelling the tumble dryer

The dryer must be installed level for correct operation. When you have installed your dryer in its final location check that it is level first side-to-side, then front to back. If the dryer is not level,

This household tumble drier is a Condenser

The weighted Annual Energy Consumption (AEc)* kWh 1) 306.0

This household tumble drier is a Automatic

Energy consumption full load; Edry - kWh 2) 2.59

Energy consumption partial load; Edry½ - kWh 2) 1.39

Power consumption: off-mode (Po) - Watts 0.14

Power consumption: left-on mode (Pl) - Watts 3.36

Prog. Time - weighted (Tt) full & partial load - minutes 3) 178

Full load (Tdry) - minutes 237

Partial load (Tdry½) - minutes 133

weighted (Ct) full & partial load 3) 81

full load (Cdry) 82

partial load (Cdry½) 80

Airborne acoustical noise emissions - dB(A) re 1 pW 70

Partial load for program “Synthetics” N/A

Average condensation efficiency - %

Regulation 932/2012.

Condensation efficiency class on a scale from G (least efficient) to

adjust the two legs up or down until your dryer is level.

Preliminary information

Once you’ve installed your dryer and before you use it, clean the inside of the drum to remove any dust that could have accumulated during transportation.

Warning ! Before you use your dryer ensure that its has been in a upright position for at least 6 hours.

Maximum load sizes: 8 kg

roduct Data - Regulation 392/2012.

Brand HOTPOINT/ARISTON Model

FTCD 871 6H1 (EU)

Rated capacity of cotton laundry for the "standard cotton programme" at full load - kg

8.0

Energy efficiency class on a scale from A+++ (low consumption) to D (high consumption)

Duration of the 'left-on mode' for power management system minutes

A (most efficient)

1) "Standard cotton” at full and partial load is the standard programme to which the

information in the label and the fiche relates. The standard cotton program is suitable to dry at cupboard level (0%) cotton laundry and is the most efficient programme in terms of energy consumption. Partial load is half the rated load.

2) based on 160 drying cycles of the standard cotton programme at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.

3) Weighted average of 3 cycles at full load and 4 cycles at half load.

A+

Energy consumption in kWh, for program “Synthetics” full load 0.68

Programme time in minute, for program “Synthetics” full load 70

Warnings

! This appliance has been designed and built

according to international safety standards. These warnings are given for safety reasons and must be followed carefully.

General safety

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• This tumble dryer has been designed for home, and not professional, use.

• Do not touch the appliance while barefoot or with wet hands or feet.

• Unplug the machine by pulling on the plug, not the cord.

• After using the dryer, turn it off and unplug it. Keep the door closed to make sure that children do not use it as a toy.

• Children should be supervised to ensure that they do not play with the dryer.

• Cleaning and user maintenance shall not be made by children without supervision.

•Children of less than 3 years should be kept away from the appliance unless continuously supervised.

• The appliance must be installed correctly and have proper ventilation. The air intake at the front of the dryer should never be obstructed (see Installation).

• Never use the dryer on carpeting where the pile height would prevent air from entering the dryer from the base.

• Check to see if the dryer is empty before

loading it.

•

The back of the dryer could become

very hot. Never touch it while in use.

• Do not use the dryer unless the filter,

watercontainer and condenser are securely in place (see Maintenance).

• Do not overload the dryer (see Laundry for maximum loads).

• Do not load items that are dripping wet.

• Carefully check all instructions on clothing labels (see Laundry).

• Do not tumble dry large, very bulky items.

• Do not tumble dry acrylic fibres at high temperatures.

• Do not turn off the dryer when there are still warm items inside.

• Clean the filter after each use (see Maintenance).

• Empty the Water Container after each use (see Maintenance).

• Clean the Heat Pump filter unit at regular intervals (see Maintenance).

• Do not allow lint to collect around the dryer.

• Never climb on top of the dryer. It could result in damage.

• Always follow electrical standards and requirements (see Installation).

• Always buy original spare parts and accessories (see Service).

To minimise the risk of fire in your tumble dryer, the following should be observed:

• Tumble dry items only if they have been

washed with detergent and water, rinsed and been through the spin cycle. It is a fire hazard to dry items that HAVE NOT been washed with water.

• Do not dry garments that have been treated

with chemical products.

• �Do not tumble dry items that have been

spotted or soaked with vegetable or cooking oils, this constitutes a fire hazard. Oil-affected items can ignite spontaneously,especially when exposed to heat sources such as a tumble dryer. The items become warm, causing an oxidisation reaction with the oil, Oxidisation creates heat. If the heat cannot escape, items can become hot enough to catch fire. Piling, stacking or storing oil-effected items can prevent heat from escaping and so create a fire hazard. If it is unavoidable that fabrics containing vegetable or cooking oil or those that have been contaminated withhair care products be placed in a tumble dryer they should first be washed with extra detergent - this will reduce, but not eliminate the hazard. They should not be removed from the dryer and piled or stacked while hot.

• �Do not tumble dry items that have previously been cleaned in or washed in, soaked in or soiled with petrol/gasoline, dry cleaning solvents or other flammable or explosive substances. Highly flammable substances commonly used in domestic environments

including cooking oil, acetone, denatured alcohol, kerosene, spot removers, turpentine,

waxes and wax removers. Ensure these items have been washed in hot water with an extra amount of detergent before being dried in the tumble dryer.

• Do not tumble dry items containing foam rubber (also known as latex foam), or similarly textured rubber like materials. Foam rubber materials can, when heated, produce fire by spontaneous combustion.

• Fabric softener or similar products should not be used in a tumble dryer to eliminate the effects of static electricity unless the practice is specifically recommended by the manufacturer of the fabric softener product.

• �Do not tumble dry undergarments that contain metal reinforcements eg. bras with metal reinforcing wires. Damage to the tumble dryer can result if the metal reinforcements come loose during drying.

• �Do not tumble dry rubber, plastic articles such as shower caps or babies waterproof covers, polythene or paper.

• �Do not tumble dry rubber backed articles, clothes fitted with foam rubber pads, pillows, galoshes and rubber coated tennis shoes.

• �Remove all objects from pockets such as

lighters and matches.

! WARNING: Never stop the dryer before

the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

Save energy and respect the environment

• Wring out all items to eliminate excess water before

tumble drying (if you use a washing machine first, select a high spin cycle). Doing this will save time and energy during drying.

• Always dry full loads - you save energy: single items or

small loads take longer to dry.

• Clean the filter after each use to contain energy

consumption costs (see Maintenance).

Care and maintenance

Disconnecting the power supply

! Disconnect the dryer when not in use or during cleaning and maintenance operations.

Cleaning the filter after each cycle

The filter is a fundamental component of the dryer: its function is to collect lint and fluff that form during drying.

Clean the filter once drying is completed, by rinsing it under running water or cleaning it with a vacuum cleaner. Should the filter become clogged, the flow of air inside the

dryer will be seriously hampered: drying times becomes longer and more energy is consumed. Moreover, the dryer may become damaged.

The filter is located in

front of the dryer seal

(see Picture).

Removing the filter:

1. Pull the filter’s plastic

handle upwards (see

Picture).

2. Clean the fluff off the filter and replace it correctly. Ensure that the filter is pushed fully home. ! Do not use the dryer unless the filter has been replaced in its holder.

Checking the drum after each cycle

Rotate the drum manually to remove smaller items (handkerchiefs) that could have been left inside the dryer.

Cleaning the drum

! Avoid using abrasives, steel wool or stainless steel cleaning

agents to clean the drum. A coloured film may appear on the stainless steel drum surface: it may be caused by a combination of water and/or cleaning agents such as wash-softeners. This coloured film does not affect the dryer’s performance.

Emptying the water container after each cycle

Remove the water container and empty it into a sink or other suitable drain outlet, then replace it correctly. Always check the water container and empty it before starting a new drying cycle.

-Failure to empty the water container may cause the following:

- The dryer stops heating (thus the load may still be damp at the end of the drying cycle).

Priming the Water Collection System

When your dryer is new, the Water Container will not collect Water until the system is primed, this will take 1 or 2 drying cycles. Once primed it will collect Water

during every cycle.

Cleaning the Heat Pump Filter Unit

• Periodically (every 5 drying cycles) remove Heat pump filter unit and clean any build up of fluff from the surface of the filter by rinsing it under running water or with your vacuum cleaner. We however recommend that you clean this filter after every drying cycle to optimize the dryers performance.

To remove Heat pump filter unit:

1. Unplug the dryer and open the door.

2. Remove the filter unit by rotating the 4 clips to the vertical position then pulling the filter unit towards you.

3. Separate the two parts of the filter unit and clean the surface of the filter.

! Warning: The front of the heat pump is made from thin metal plates.

Take care that you do not damage these or cut yourself when cleaning, removing or replacing the filter unit.

4.Whenever you clean the Heat pump filter unit always clean any build up of fluff from

the surface of the metal

plates. Carefully clean this fluff off with a damp cloth,sponge or vacuum

cleaner. Never use your Fingers.

5. Assemble the two parts of the filter clean

the surface of the seals and replace with the 4 clips into the horizontal position, sure that the catches have been secured.

Cleaning the tumble dryer

• The external metal, plastic and rubber parts can be cleaned with a damp cloth.

• Clean the front air intake grille regularly (every 6 months)

with a vacuum cleaner to remove any lint, fluff or dust deposits. Furthermore, remove any lint deposits from the front part of the Heat pump filter unit and from the filter area, using a vacuum cleaner every so often.

! Do not use solvents or abrasives. ! Have the dryer checked regularly by authorised technical

personnel in order to ensure that the electrical and mechanical parts work safely (see Assistance).

Heat Pump Protection System

The heat pump system has a compressor protection feature that operates if you open the door or there is a power disruption or if you turn off the dryer. This system will prevent the heat pump compressor from starting for 5 minutes after the door is closed and the programme is started.

Quick Tips !Remember to clean your filter and Heat Pump filter unit after each load. ! Remember to empty your water container after each load. ! Doing this will keep your machine working at its BEST!

Water container

Heat pump filter unit

Catches

Model & Serial numbers

Handle

Rating plate

Cover

Filter

Adjustable feet

Air intake

Control panel

PROGRAMME

Selection Buttons

ON/OFF

The ON/OFF button : - if pressed when the dryer is running: If the display shows stops. If the display shows botton and the display counts down 3, 2, 1 and then stops. Press and hold again for more than 3 seconds, the display

brieﬂ y shows

The PROGRAMME selection buttons set the programme: press the button corresponding to the programme you want to select (see Start and Programmes).

The OPTION buttons/indicators: these buttons select available options for your selected programme (see The Controls). The indicators on the display unit next to the bottom buttons light to show that the option has been selected. The START/PAUSE button/light programme. When a programme is running, pressing this button in pauses the programme, there will be one beep, the display will show

The light is green when the programme is running, ﬂ ashing

POWER ON

PAUSE

TURNING OFF

PRESS AND HOLD

and the dryer stops.

the dryer

, hold the

starts a selected

Button

Display Unit

CHILD LOCK &

OPTIONS

Buttons & Lights

amber if the programme has been paused or ﬂ ashing

green if on standby waiting to start a programme (see Start and Programmes).

Note: This light also ﬂ ashes amber during the Post Care phase of a programme.

The Display Unit gives warnings and information about the programme selected and its progress (see next page).

The CHILD LOCK button/icon button after selecting your programme and any options, this prevents the programme settings from being changed,

the display will brieﬂ y show

is lit, the other buttons are disabled. Hold the button to

cancel and the icon will go out, the display will brieﬂ y show

UNLOCKED

Note: This tumble dryer, in compliance with new energy

saving regulations, is ﬁ tted with an automatic standby

system which is enabled after about 30 minutes if no activity is detected. Press and hold the ON-OFF button

until the display brieﬂ y shows

then reactivates.

START/PAUSE Button & Light

: Press and hold this

LOCKED

. When the icon

POWER ON

, and the dryer

Laundry

Sorting laundry

• Check the symbols on the care labels of the various gar-

ments to verify whether the garments can be safely tumble dried.

• Sort laundry according to the type of fabric.

• Empty all pockets and check for loose buttons.

• Close zips and hooks and fasten belts and strings without tightening them.

• Wring out garments to remove the maximum amount of water possible.

Do not load the dryer when garments are dripping wet.

Maximum load sizes

Do not overload the drum. The following values indicate the weight of dry garments: Natural fibres: maximum kg Synthetic fibres: maximum kg

! Do not overload the dryer as this may result is reduced drying performance.

Care labels

Always check the care labels, especially when placing garments in the tumble dryer for the first time. Below are the most commonly used symbols:

May be tumble dried.

Do not tumble dry.

Tumble dry – high heat.

Tumble dry – low heat.

The Display

Selecting your language

The ﬁ rst time you turn on your dryer you should select your preferred language

from the available list.

To change: the language current selection must ﬂ ash, on the ﬁ rst

line of the display.

- Press the On/Off button to turn off the display then press and hold all 3 buttons:

5 seconds.

- Press the down through the list.

- When your required language is ﬂ ashing on the top line of the

display, pressing the

Heat Level, Timed Dry, and Sensor Dry for

Heat Level or the Timed Dry button to scroll up or

Sensor Dry button will select your choice.

Understanding the display

Programme selection and display

The selected programme is shown on the ﬁ rst line of the display, this message is shown while the programme is running. Eight of the buttons have two selections, press the button once for the ﬁ rst choice and press again for the second choice, your selected programme is displayed. The ﬁ nal button selects My Cycle. My Cycle. When you select the My Cycle button the Display will show your selected programme with ‘M’ before its

name. ie.

M STANDARD COTTON

(see Start and Programmes).

Dryness levels

During programme selection for an automatic programme that has different dryness levels available (see Programmes Table).

The second line of the display shows the dryness level you require, for each press of the Dryness Level button the next

option from the list below is selected and displayed. The display also shows 1 to 7 bars depending on your selection and these are displayed during the programmes progress.

! Some automatic programmes do not allow the dryness level to be changed or do not have all the dryness level options.

DAMP

IRON DRY

HANGER PLUS

HANGER DRY

LIGHT DRY

CUPBOARD DRY

EXTRA DRY

Dries your items ready to be ironed using a machine or rotary ironer.

Dries your items ready to be ironed with a hand iron.

Dries your delicate items ready to be hanged for ﬁ nal drying.

Dries your items ready to be hanged for ﬁ nal drying.

Dries your delicate items ready to be put away.

Dries your items ready to be put away.

Dries your clothes ready to be worn.

Programme progress

The second line of the display shows the status of the programme as it progresses: (long messages scroll across the line)

DRY

COOL TUMBLE

HEATING

READY

END OF CYCLE, CREASE CARE

END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE

(if option Crease Care selected)

The Display

Timed drying

After selecting a programme that has a Timed Dry

option, press the increment the selected time, each time you press and release the button (see Start and Programmes).

Each press reduces the time duration and number of available time options depending on the programme/material selected.

The Timed Dry icon

The selected time remains displayed after the programme starts, but can be changed anytime you wish.

is displayed next to the time..

Timed button and the display will

Delay and Time to End

Some programmes can have a delayed start (see Start and Programmes). Press the

button and the icon ﬂ ashes.

Each press of the Delay button

delay setting in 1 hour increments, from: to

seconds cancels the delay.

The delay time is shown on the display next to the Delay button.

The display counts down the minutes of the delay period after the Start/Pause button display shows

,then and then after a couple of

STARTS IN

, Delay

advances the

is pressed. The second line of the

You can change or cancel the delay time selected anytime if you wish.

After the Start/Pause button is pressed the Delay or Time to End is displayed in hours and minutes and counts down each

minute.

Time to End

After the delay period ﬁ nishes, or for all the programme if delay not selected, this part of the display will show:

- the estimated time to the end of the programme, for automatic programmes

- the actual time remaining during a timed programme When timed programmes are selected the time displayed throughout the cycle is the actual time remaining. When Automatic programmes are selected the time displayed is an estimate of the time remaining. When the programme is selected the display shows the time required to dry a full load. The time remaining is constantly monitored during the drying cycle and is updated to show the best forecast.

The colons between the hours and minutes in the display ﬂ ash to show the time is counting down.

My Cycle button:

First time you press this button the display will show

After selecting your favorite programme and options you can save these settings by pressing and holding in the My Cycle button for at least 5 seconds, the top line will show a ﬂ ashing M followed by the selected programme. The

buzzer will then beep and the second line of the display shows

The next time you need this programme press the M, button, then the Start/Pause button (and this programme will run.

If you wish, you can change your stored favorite, by selecting a new programme and/or options and press and hold in the M button (as above).

PRESS AND HOLD TO STORE

MEMORY

Start and Programmes

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see Laundry).

3. Open the door and make sure the ﬁ lter is clean and in

place and the water container is empty and in place (see Maintenance).

4. Load the machine and make sure items are not in the way of the door seal. Close the door.

5. If the Display is not lit: Press the ON/OFF button .

6. Press the Programmes Selection button that corresponds with the type of fabric being dried by checking the Programmes Table (see Programmes) as well as the indications for each type of fabric (see Laundry).

- if the M button is selected; steps 7 and 8 are not required

(see below).

7. Choose Timed Drying or Dryness Levels option:

- If Timed Drying press and release the Timed button until

the required time is displayed.

or - To change from default dryness setting, press and

release the Dryness Levels button until required level is

indicated. ! See Programmes Table, for more details: availability of

Dryness Levels, Timed Dry and Options.

8.Set a delay time and other options if necessary (see The Display).

9.Press the Start/Pause button

will show the estimated time to end. During the drying

programme, you can check on your laundry and take out items that are dry while others continue drying. When you

to begin. The display

close the door again, press the Start/Pause button in order to resume drying. If you open the door to check your laundry you will extend the drying time as the heat pump compressor will not start for 5 minutes after you close the door and press the Start/Pause button (see The Controls).

10. During the last few minutes of Drying Programmes, before the programme is completed, the ﬁ nal COOL TUMBLE phase is entered (fabrics are cooled), this phase

should always be allowed to complete.

11. At the end of the drying cycle a message is displayed:

END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE

- if is shown, the buzzer will beep 3 times (Note: If the SOUND option was selected the buzzer beeps 3 times every 30 seconds for 5 minutes).

END OF CYCLE, CREASE CARE

- if option has been selected and if you do not remove the laundry immediately, the dryer will tumble occasionally for 10 hours or until you open the door, the buzzer will beep 3 times

to conﬁ rm the programme is completed.

12. Open the door, take the laundry out, clean the ﬁ lter and replace it. Empty the Water Container and replace it (see

Maintenance).

13. Unplug the dryer.

is shown, Crease Care

Drying times

Drying times are approximate and may vary depending on the following:

• Amount of water retained by items after the spin cycle: towels and delicate items retain a lot of water.

• Fabrics: items of the same fabric, but with different texture and thickness may have different drying times.

• Amount of laundry: single items and small loads may take longer to dry.

• Drying: if items are to be ironed, they can be removed from the dryer while still slightly damp. Items that require complete

drying can be left longer.

• Heat setting.

• Temperature of the room: the lower the temperature of the room, the longer it will take for the dryer to dry clothing.

• Bulk: certain bulky items require special care during the drying process. We suggest removing these items and replacing them

in the dryer once they have been shaken out: repeat this procedure several times during the course of the drying cycle.

! Do not over-dry items. All fabrics contain natural dampness which helps to keep them soft and ﬂ uffy.

The drying times provided refer to the automatic Cupboard dry programmes.

The Timed drying settings are also indicated to enable you to select the most suitable timed option. The weight refers to dry items.

n° Programme

Standard

Cotton

max

Shirts

Cottons

3 kg

Bed & Bath

max

Anti

Allergy

max or 4 kg

Synthetics

3 kg

Shirts

Sytnthetic

3 kg

Jeans

3 kg

Duvet

Description of program

The duration of the drying cycles can be checked on the display

• This is a programme for cotton items.

• The Standard Cotton programme to EU Regulation 392/2012 is Programme 1 selection with High Heat and Dryness Level Cupboard Dry (the standard/default starting configuration). It is the most efficient programme in terms of energy consumption (to EU.392/2012).

• This is a programme for shirts made from cotton.

• Loads dried using the Cupboard Dry setting are usually ready to wear, the edges or seams may be slightly damp. If this is the case, try turning the shirts inside out and running the programme again for a short period.

• This is a programme for cotton towels and sheets.

• Loads dried using the Extra Dry setting are usually ready to use, the edges or seams may be slightly damp especially on

large items. If this is the case, try opening them out and running the programme again for a short period.

• This programme has the ‘Seal of Approval’ endorsement from Allergy UK, which reflects the effective reduction and elimination of allergens from the clothes with the special Anti Allergy cycle. With this programme, thanks to the achievement of constant temperature for an extended period of time, the effects of the most common allergens (including House Mites and Pollen) are neutralised.

• Can be used on a full size wet load to dry and treat, or on a 4 kg dry load just to treat your laundry. If the display shows

CLEAN FILTER TO ENSURE ANTI ALLERGY ACTION

: Clean the filter and re-start the programme.

• This is a programme for items of Synthetic with low heat setting or Synthetic/Cotton mixtures with medium heat setting.

• This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such as polyester and cotton.

• This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.

• Do not mix dark and light coloured items.

• It can also be used on other garments made from the same material, such as jackets.

• Loads dried using the Extra Dry setting are usually ready to wear, the edges or seams may be slightly damp. If this is the case, try turning the jeans inside out and running the programme again for a short period.

! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery. ! Take care with this programme DO NOT dry any items that are damaged which could result in the filling blocking the filter

and air vent resulting in a fire hazard.

• Must only be used on single size duvets: NOT suitable for double or king size items.

• Loads dried using this programme are usually ready to use, but may be slightly damp in places. If this is the case, try opening them out and shaking them and running the programme again for a short period.

• Also suitable for down filled jackets.

• Select high heat for Cotton Duvets and medium heat for Synthetic duvets.

Note:

1 - The duration of the program will depend on the size of the load, types of textiles, the spin speed used in your washer and any extra options

selected.

n° Programme

Wool

1 kg

Silk

0,5 kg

Delicates

2 kg

Baby

2 kg

Cuddly Toy

2,5 kg

Heat & Enjoy

3 kg

Refresh

Easy Iron

Description of program

The duration of the drying cycles can be checked on the display

• This is a programme for tumble dryer safe garments marked with the symbol

• We recommend that garments are turned inside out before drying.

• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly

damp. Allow these to dry naturally as over-drying could damage garments.

! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and shape. ! This programme is not suitable for Acrylic garments.

• This is a programme for drying your delicate silk.

• Loads dried using the Cupboard Dry setting are usually ready to use, but on some garments the edges may be slightly

damp. If this is the case, try opening them out or turn items inside out and running the programme again for a short period.

• This is a programme for drying your delicate clothes ie. Acrylics.

• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly

damp. If this is the case, try turning items inside out and running the programme again for a short period.

• This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille) and for

drying your delicate clothes.

• DO NOT dry items such as bibs and nappy pants with plastic coverings.

• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly

damp. If this is the case, try turning items inside out and running the programme again for a short period.

• With this programme you can remove dust easier and wash the cuddly toys more often because the drying time is very

much reduced compared to drying in the open air. It is a delicate drying cycle that dries at low temperature and with soft mechanical action to maintain at best the original look and shine of the fur.

Note: For allergy protection, just freeze cuddly toys for 24 hours then wash and dry them. Repeat every 6 weeks.

• Before drying remove accessories such as clothes, collars or sound boxes and protect plastic eyes with masking tape

after drying them with a cloth.

• The programme time will vary dependant on the exact make up of the load. The maximum load should not exceed 2.5

kg and no individual item should be greater than 600 g.

• This programme helps to heat towels & bathrobes for a warm sensation after a bath or shower. It is also useful for warming

clothes before dressing during winter. The cycle heats clothes to 37°C (Body Temperature), the display shows

HEATING

and runs at this temperature for a maximum of 4 hours or until you stop the cycle by opening the door when the display shows

READY

Note: The Start/Pause button is disabled during this programme. ! ‘Refresh’ is not a drying programme and should not be used for wet articles of clothing.

• It can be used on any load size, but is more effective on smaller loads.

• Do not overload your dryer (see Laundry).

• This is a 20 minute programme that airs your clothes with cool air. Also use to cool warm clothes.

• ‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which fluffs the

fibres of clothing that have been left in the same position/location for an extended period of time. The cycle relaxes the fibres and makes them easier to iron and fold.

! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.

• For best results:

1. Do not load more than the maximum capacity. These numbers refer to the dry weight: (Fabric-Maximum load) Cotton and

Cotton mixtures-2.5 kg; Synthetics-2 kg; Denim-2 kg.

2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put them away in the closet.

Should this not be possible repeat the programme.

Note:

1 - The duration of the program will depend on the size of the load, types of textiles, the spin speed used in your washer and any extra options

selected.

Start and Programmes

The Controls

! Warning, after pressing the START/PAUSE button ,

the programme cannot be changed. To change a selected programme, press the START/PAUSE button flashes Amber to indicate the programme is paused. Select the new programme and any options required, the light will then flash green. Press the START/PAUSE button and the new programme will start.

• Option buttons

the light

again

These buttons serves to personalise the selected programme according to personal requirements. Not all options are available for all programmes. Some options are incompatible with the ones previously set. If the button of any unavailable option is pressed, the buzzer will beep 3 times. If the option is available, the option light will stay on.

• TIME DISPLAY The display shows either the amount of time delay remaining or an indication of the amount of time left for a drying programme (see The Display). The display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a fault code number (see Troubleshooting).

• Empty Water Container

(Messages about emptying can be ignored if you have plumbed your dryer into a drain as there is no need to empty the water container). Messages are displayed to reminds you to empty the water container (see The Display). If the water container fills during a programme, the heater turns off and the dryer does a period of Cool Tumble. After this it stops and a message tells you to container and restart the dryer or the clothes will not dry. After re-starting the dryer the message will take a few seconds to go out. To avoid this always empty the water container each time you use the dryer (see Maintenance).

EMPTY THE WATER CONTAINER

. You must empty the water

Delay Timer (Time Delay)

The start of some programmes (see The Display and Programmes tables) can be delayed for up to 24 hours. Ensure the water container is emptied before setting a delayed start.

Crease Care

The pre-care option is only available if a delayed start has been selected. It tumbles the clothes occasionally during the delayed period to help prevent creases developing. The post-care option occasionally tumbles the clothes after end of the drying and cool tumble cycles to prevent creases developing, should you not be available to remove the load immediately the programme is complete Note: The START/PAUSE this phase. Selecting this option enables both the pre and

post care functions if appropriate.

Note: If you have selected the Sound option this option is

not available.

Heat Level button, Display and Icons

Not all programmes allow you to change the heat level and some programmes allow all three heat level options: Low, Medium and High. When the heat level options are available pressing this button changes the heat level and the display briefly shows the selected heat level, along with a display of the selected level icon:

HIGH HEAT

MEDIUM HEAT

light flashes Amber during

LOW HEAT

• Door Opening Opening the door during a programme will stop the dryer and have the following effects: Note: The START/PAUSE Post Care phase of a programme

� • The display shows

�• During a delay phase the delay will continue to count down.

The START/PAUSE the delay programme. The display will change to show current status.

• The START/PAUSE the programme. The display will change to show the current status.

• During the Post Care phase, the programme ends. Pressing the START/PAUSE from the beginning.

�• Note

If you have a power cut, switch off the power or remove the plug. When power is restored, press and hold the On/Off button until the display briefly shows reactivates. Then press the START/PAUSE programme will resume.

PAUSED

light flashes Amber during the

button must be pressed to resume

button will restart a new programme

POWER ON

and the dryer

button and the

Sound

Available on all programmes and allows the buzzer to give a signal at the end of the drying cycle, to remind you that the clothes are ready to be removed. Note: If you have selected the Crease Care option this option is not available

Extra Care

This Anti-Ageing function for Cottons helps to maintain the brightness of your laundry for a long time, thanks to the correct drum rotation (reduced in the last part of the cycle) and the correct temperature.

Quick Dry

This option is for small loads up to 1kg. Note: can only be used with the ‘Cupboard Dry’ setting.

Troubleshooting

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following troubleshooting suggestions:

Problem:

The tumble dryer won’t start.

Drying cycle will not begin.

Its taking a long time to dry.

Possible causes / Solution:

• The plug is not plugged into the socket, or not making contact.

• There has been a power failure.

• The fuse has blown. Try to plug another appliance into the socket.

• You are using an extension cord? Try to plug the dryer’s power cord directly into the socket.

• The door is not closed securely?

• The programme has not been set properly (see Start and Programmes).

• The Start/Pause button has not been pressed (see Start and Programmes).

• You have set a delayed time (see Start and Programmes).

• The filter has not been cleaned (see Maintenance).

• The water container needs emptying? The empty water message is displayed? (see Maintenance).

• The heat pump filter needs cleaning? (see Maintenance).

• The temperature setting is not ideal for the type of fabric you are drying (see Start and Programmes, and see Laundry).

• The correct drying time has not been selected for the load (see Laundry).

• The air intake grille is obstructed (see Installation, and see Maintenance).

• The items were too wet (see Laundry).

• The dryer was overloaded (see Laundry).

Empty water message is displayed but the dryer has only been running for a short period.

Empty water message is displayed and the water container is not full.

Programme finishes and clothes are damper than expected.

The display shows a fault code F followed by one or two numbers.

The display briefly shows

DEMO ON

every 6 seconds.

The water container was probably not emptied at the start of the programme. Do not

• wait for the empty water signal, always check and empty the container before starting

a new drying programme (see Maintenance).

END OF CYCLE, CLEAN FILTER AND EMPTY THE WATER BOTTLE

• This is normal, the: message is shown as a reminder to empty the container (see The Display and Start and Programmes).

! For safety the dryer has a maximum programme time of 5 hours. If an automatic programme has not sensed the required final moisture in this time the dryer will complete the programme and stop. Check the above points and run the programme again, if the results are still damp, contact the Service Centre (see Service).

• If the display shows a fault:

- Turn off and remove the plug. Clean the filter and the heat pump filter unit (see Maintenance). Then replace the plug, turn on and start another programme. If a fault is then displayed: Note down the code and contact the Service Centre (see Service).

• The dryer is in ‘Demo’ mode. Press and hold both the On/Off and Start/Pause buttons for 3 seconds. The display will show dryer will resume normal operation.

DEMO OFF

for 3 seconds and then the

The lights on the dryer control panel are off although the dryer is switched on.

• The dryer has gone into standby mode to save power. This occurs if you have had a power cut or leave your dryer either without starting a programme or after your drying programme has finished.

- Press and hold the On/Off button and the lights will come on.

Service

Heat Pump System

This dryer is fitted with a sealed heat pump system to dry your clothes. To operate, the heat pump contains fluorinated greenhouse gases ( F gases) which are covered by the Kyoto Protocol. These F gases are contained in a hermetically sealed unit. This sealed unit contains kg of the F gas R134a which acts as a refrigerant. GWP = 1430 (0.4 t C02). If the sealed unit fails then it must be replaced by a new sealed unit. Contact your nearest service centre for advise. Note: The gases contained in the sealed unit are not hazardous to health, but if they escape they will have an impact on global warming.

Before calling the Service Centre:

• Use the troubleshooting guide to see if you can solve the problem yourself (see Troubleshooting).

• If not, turn off the dryer and call the Service Centre closest to you.

0,29

Spare Parts

This dryer is a complex machine. Repairing it yourself or having a nonauthorised person try to repair it could cause harm to one or more persons and to the machine, and could invalidate the spare parts warranty. Call an authorised technician if you experience problems while using the machine. Please note that it is an offence for an unqualified person to undertaken any servicing or repair work that involves breaking into the sealed heat pump unit.

What to tell the Service Centre:

• Name, address, and post code;

• telephone number;

• the type of problem;

• the date of purchase;

• the appliance model (Mod.);

• the dryer serial number (S/N). This information can be found on the data label inside the door of the machine.

Information on recycling and disposal

As part of our continual commitment towards environmental protection, we reserve the right to use recycled quality components to reduce costs for our customers and to minimise materials wastage.

• Disposing of the packaging materials: follow local regulations to allow for recycling of packaging materials.

• In order to minimise the risk of injury to children, remove the door and plug, then cut the power supply cord flush with the appliance. Dispose of these parts separately to prevent the appliance from being connected to a power supply socket.

Disposal of old household appliances

The European Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household

electrical appliances must not be disposedof in the normal unsorted municipal waste stream. Old appliances must be collected separately in order tooptimise the recovery and recycling of the materialsthey contain and reduce the impact on

human healthand the environment. This dryer has a sealed heat pump unit containing Fgases which should be recovered and destroyed.The crossed out “wheeled bin” symbol on theproduct reminds you of your obligation,thatwhen you dispose of the appliance it must beseparately collected.Consumers should contact their local authority orretailer for information concerning the correct disposalof their old appliance.

This appliance has been designed, constructed and distributed in compliance with the requirements of European Directives:

- LVD 2014/35/EU, EMC 2014/30/EU and RoHS 2011/65/EU.

Bedienungsanleitungen

WÄSCHETROCKNER

Deutsch

FTCD 871

Wenn Sie den Wäschetrockner das erste Mal einschalten, müssen Sie die von Ihnen bevorzugte Bedienungssprache wählen – siehe Display

Installierung

Aufstellung, 18

Hinweise, 20

Wartung und Pflege, 22

Bedienblende, 24

Wäsche, 24

Display, 25

Start und Programme, 27

Fehlersuche, 31

Kundendienst, 32

www.hotpoint.eu

! Dieses Symbol erinnert Sie daran,

das vorliegende Handbuch zu lesen.

! Bewahren Sie diese Gebrauchsanweisung immer in Nähe

des Wäschetrockners auf, um sie bei jedem Bedarf leicht konsultieren zu können. Falls das Gerät verkauft oder an andere Personen übergeben wird, händigen Sie auch dieses Heft aus, um es so den neuen Besitzern zu ermöglichen, von den Hinweisen zum Gebrauch des Wäschetrockners Kenntnis zu nehmen.

! Lesen Sie bitte diese Hinweise aufmerksam durch: sie

enthalten wichtige Hinweise zu Aufstellung und Anschluss und nützliche Empfehlungen zum Gerätebetrieb.

10 mm

15 mm

Aufstellung

Aufstellungsort des Wäschetrockners

• Übermäßige Hitze kann den Wäschetrockner schädigen; deshalb im Abstand von Gasherden, Öfen, Heizkörpern oder Kochfeldern platzieren. Der Trockner soll bei einer Zimmertemperatur von 20 bis 23 °C angeschlossen werden für eine optimale Wirkung. Er funktioniert jedoch auch bei einer Zimmertemperatur von 14 bis 30 °C. Falls das Haushaltsgerät unter einem Arbeitstisch eingebaut werden soll, muss ein Freiraum von 10 mm zwischen der oberen Geräteplatte und anderen, darüber befindlichen Gegenständen vorgesehen werden, sowie 15 mm Freiraum zwischen den Seitenwänden des Geräts und den Wänden bzw. den angrenzenden Einrichtungsgegenständen. Nur auf diese Weise wird eine ausreichende Luftzirkulation gewährleistet. Das Gerät muss mit der Rückseite gegen eine Mauer installiert werden.

Belüftung

• Während des Betriebs des Wäschetrockners muss eine ausreichende Belüftung vorhanden sein. Vergewissern Sie sich, dass der Trockner in einem trockenen, Raum aufgestellt wird, der über eine ausreichende Luftzirkulation verfügt. Nur eine ausreichnde Luftzirkulation gewährleistet die einwandfreie Funktion des Trockners. Keinesfalls darf das Gerät in kleinen verschlossenen Räumen auggestellt oder in Möbelteile integriert werden.

! Falls der Trockner in einem kleinen oder kalten Raum

benutzt wird könnte Wasser auf dem Gerät kondensieren.

! Wir raten davon ab, den Trockner in einem Schrank aufzustellen; auf keinen Fall darf das Haushaltsgerät hinter einer abschließbaren Tür, einer Schiebetür oder einer Tür mit umgekehrtem Türanschlag platziert werden.

Wasserablauf

Falls das Gerät in der Nähe eines Ablaufschlauches aufgestellt wird, können Sie das Kondenswasser direkt abführen, ohne den Wasserauffangbehälter zu verwenden. In diesem Fall muss der Wasserauffangbehälter nicht nach jedem Trockenzyklus entleert werden. Falls der Trockner über oder neben einer Waschmaschine positioniert wird, kann dieser Wasserablaug mitbenutzt werden. Es reicht aus, den in Abbildung A gezeigten Schlauch abzutrennen und an den Ablauf anzuschließen. Falls der Ablauf weiter entfernt ist als der Schlauch lang ist, können Sie zur Überbrückung einen Schlauch mit gleichem

Durchmesser und der erforderlichen Länge kaufen und anschließen. Dazu den neuen Schlauch wie in Abbildung B angegeben an der Stelle des vorherigen montieren.

! Der Ablauf darf maximal einen Meter oberhalb des

trocknerbodens montiert werden.

! Nachdem der Wäschetrockner aufgestellt wurde,

sicherstellen, dass der Ablaufschlauch nicht geknickt oder gekrümmt ist.

Abb. A Abb. B

H<1m

Elektroanschluss

Bevor Sie den Stecker in die Steckdose stecken, folgende Prüfungen ausführen:

• Vergewissern Sie sich, dass Ihre Hände trocken sind.

• Die Steckdose muss geerdet sein.

• Die Steckdose muss der maximalen Leistungsaufnahme des Geräts entsprechen, die auf dem Typenschild mit den Betriebsdaten angegeben ist.

• Die Netzspannung muss den Werten entsprechen, die auf dem Typenschild mit den Betriebsdaten angegeben sind.

• Die Steckdose muss mit dem Stecker des Wäschetrockners kompatibel sein. Sollte dies nicht der Fall sein, dann lassen Sie den Netzstecker oder die Steckdose austauschen.

! VERWENDEN SIE KEINE VERLÄNGERUNGEN.

! Der Trockner kann nicht in Außenräumen

aufgestellt werden, auch wenn diese geschützt sind. Es können große Gefahrensituationen entstehen, wenn dieses Haushaltsgerät Regen oder Gewittern ausgesetzt wird.

! Nach der Aufstellung des Trockners müssen das Stromkabel und der Stecker zugänglich bleiben.

! Achten Sie darauf, dass das Stromkabel nicht geknickt oder gequetscht ist.

Dieser Haushaltswäschetrockner ist Ein Kondens.

Der gewichtete jährliche Energieverbrauch (AEc)* Kwh 1) 306.0

Energieverbrauch bei vollständiger Befüllung; Edry- kWh 2) 2.59

Leistungsaufnahme im Aus-Zustand (Po) - Watts 0.14

Vollständige Befüllung (Tdry) - Minuten 237

Teilbefüllung” (Tdry½) - Minuten 133

Gewichtete (Ct) vollständige Befüllung und Teilbefüllung 3) 81

Vollständige Befüllung Cdr 82

Teilbefüllung Cdry½ 80

Luftschallemissionen - dB(A) re 1 pW 70

Kunstfasern: vollständige Befüllung - Minuten 70

Kunstfasern: Teilbefüllung N/A

Marke

! Änderungen am Kabel oder am Stecker dürfen nur durch autorisiertes Fachpersonal vorgenommen werden.

! Das Stromkabel ist regelmäßig zu überprüfen. Sollte das Stromkabel beschädigt sein, muss es vom Hersteller, dessen Kundendienst oder von anderem, qualifizierten Fachpersonal ersetzt werden, um Gefahren zu vermeiden. (siehe Kundendienst). Neue oder längere Stromkabel werden von autorisierten Ersatzteilhändlern kostenpflichtig zur Verfügung gestellt.

! Der Hersteller übernimmt keine Haftung, falls diese Vorschriften nicht eingehalten werden.

! Bei Fragen zur Aufstellung oder dem Anschluss ziehen Sie gegebenenfalls einen Elektrofachmann zu Rate.

Maximale Lademengen 8 kg

rodukt daten - V orschrift 9 32/2012.

HOTPOINT/ARISTON Modell

FTCD 871 6H1 (EU)

Nennkapazität Baumwollwäsche für das "StandardBaumwollprogramm" bei vollständiger Befüllung - kg

Energieeffizienzklasse (A+++ niedriger Verbrauch) bis D (hoher Verbrauch)

Dieser Haushaltswäschetrockner ist Automatisch

Standard-Baumwollprogramm: Energieverbrauch bei Teilbefüllung; Edry- kWh 2)

8.0

A+

1.39

Ausrichtung des Wäschetrockners

Für einen einwandfreien Betrieb muss das Gerät perfekt eben aufgestellt werden. Prüfen Sie die Ausrichtung des Geräts nach der Installation an seinem Bestimmungsort erst auf beiden Seiten und dann vorne und hinten. Steht die Maschine nicht eben, dann stellen Sie die vorderen Stellfüße so ein, dass die Maschine eben steht.

Allgemeine Informationen

Reinigen Sie nach dem Aufstellen und vor der Inbetriebnahme des Trockners den Innenraum der Trommel, um eventuelle Verschmutzungen zu entfernen, die sich während des Transports angesammelt haben könnten.

ACHTUNG: Vergewissern Sie sich, dass Ihr Trockner mindestens sechs Stunden lang in vertikaler Position gestanden hat, bevor Sie ihn benutzen.

Leistungsaufnahme im unausgeschalteten Zustand (Pl) - Watts 3.36

Dauer des unausgeschalteten Zustandes für die Leistungssteuerung - Minuten

Gewichtete Programmdauer (Tt) bei vollständiger Befüllung und Teilbefüllung in Minuten 3)

Kondensationseffizienzklasse auf einer Skala von G (geringste Effizienz) bis A (höchste Effizienz)

Durchschnittliche Kondensationseffizienz - %

1) Das "Standard-Baumwollprogramm" ist bei vollständiger Befüllung und Teilbefüllung das Standardtrocknungsprogramm, auf das sich die Informationen auf dem Etikett und im Datenblatt beziehen, dass dieses Programm zum Trocknen normaler nasser Baumwolltextilien geeignet und in Bezug auf den Energieverbrauch für Baumwolle am effizientesten ist.

2) Jährlicher Energieverbrauch auf der Grundlage von 160 Trocknungszyklen für das Standard-Baumwollprogramm bei vollständiger Befüllung und Teilbefüllung sowie des Verbrauchs der Betriebsarten mit geringer Leistungsaufnahme. Der tatsächliche Energieverbrauch je Zyklus hängt von der Art der Nutzung des Geräts ab.

3) In drei Zyklen bei voller Ladung und 4 Zyklen bei halber Ladung gemessenes Durchschnittsgewicht.

Vorsch rift 932/2 012.

Kunstfasern: energieverbrauch bei vollständiger Befüllung; kWh 0.68

178

Hinweise

! Dieses Haushaltsgerät wurde unter Beachtung der internationalen Sicherheitsnormen geplant und hergestellt. Die nachfolgenden Hinweise werden aus Sicherheitsgründen geliefert und sind aufmerksam zu beachten.

Allgemeine Sicherheit

• Dieser Wäschetrockner darf von Personen (einschließlich Kinder ab 8 Jahren) mit eingeschränkten körperlichen, geistigen oder sensorialen Fähigkeiten oder ohne ausreichende Erfahrung und Kenntnis verwendet werden, vorausgesetzt, sie werden durch eine für ihre Sicherheit verantwortliche Person beaufsichtigt und eingewiesen.

• Dieser Trockner wurde nur zum häuslichen Gebrauch und nicht für gewerbliche Zwecke geplant.

• Berühren Sie das Gerät nicht barfuß oder mit nassen Händen oder Füßen.

• Trennen Sie das Haushaltsgerät vom Stromnetz, indem Sie den Stecker und nicht das Kabel ziehen.

• Schalten Sie den Wäschetrockner nach dem Gebrauch aus und trennen Sie ihn vom Stromnetz ab. Halten Sie die Gerätetür geschlossen, um zu vermeiden, dass Kinder sie zum Spielen benutzen können.

• Kinder müssen beaufsichtigt werden, um sicherzustellen, dass sie nicht mit dem Wäschetrockner spielen.

• Wartung und Reinigung dürfen nicht von unbeaufsichtigten Kindern ausgeführt werden.

• Kinder unter 3 Jahren müssen von dem Wäschetrockner ferngehalten werden, wenn sie nicht ständig beaufsichtigt werden.

• Das Haushaltsgerät muss ordnungsgemäß aufgestellt werden und über eine angemessene Lüftung verfügen. Die Belüftungsöffnung auf der Vorderseite des Wäschetrockners und die Luftabzüge auf der Rückseite dürfen nicht verstopft sein (siehe Aufstellung).

• Benutzen Sie den Wäschetrockner nie auf einem Teppichboden, dessen Florhöhe die Luftzufuhr über die Unterseite des Geräts verhindert.

• Prüfen Sie, dass der Trockner leer ist, bevor Sie ihn füllen.

•

• Benutzen Sie den Wäschetrockner

• Überladen Sie den Trockner nicht (siehe

• Geben Sie keine völlig nassen

• Befolgen Sie aufmerksam alle auf

• Entfernen Sie alle Gegenstände aus

• Geben Sie keine besonders großvolumigen

• Trocknen Sie keine Kunstfasern bei hohen

• Schalten Sie den Wäschetrockner nicht

• Reinigen Sie das Flusensieb nach jedem

• Entleeren Sie den Wasserauffangbehälter

• Reinigen Sie regelmäßig die

• Vermeiden Sie die Ansammlung von Flusen

• Steigen Sie nicht auf die obere Platte

• Beachten Sie immer die Vorschriften und

• Kaufen Sie immer Originalersatzteile und

Die Rückseite des Wäschetrockners

kann sehr warm werden: berühren Sie sie nie, wenn sich das Gerät in Betrieb befindet.

nicht, wenn das Flusensieb, der Wasserauffangbehälter und der Kondensator nicht korrekt positioniert sind (siehe Wartung).

Wäsche, maximale Füllmenge).

Kleidungsstücke in das Gerät.

den Etiketten der Kleidungsstücke angegebenen Hinweise zum Waschen der Teile (siehe Wäsche).

den Taschen, besonders Feuerzeuge (Explosionsgefahr).

Teile in den Trockner.

Temperaturen.

aus, wenn er noch warme Kleidungsstücke enthält.

Gebrauch (siehe Wartung).

nach jedem Gebrauch (siehe Wartung).

Kondensatoreinheit (siehe Wartung).

im Trockner.

des Wäschetrockners, da das Gerät beschädigt werden könnte.

die elektrischen Eigenschaften des Geräts (siehe Aufstellung).

-zubehör (siehe Kundendienst).

Hinweise zur Minimierung des Brandrisikos im Wäschetrockner:

• Nur solche Artikel in den Trockner legen, die mit Waschmittel und Wasser gewaschen und danach gründlich gespült und geschleudert wurden. Artikel, die NICHT mit Wasser gewaschen wurden, stellen ein Brandrisiko dar.

• Keine Wäsche trocknen, die mit Chemikalien behandelt wurde.

• Keine Wäsche trocknen, die mit Gemüse- oder Speiseöl verschmutzt oder vollgesogen ist, da dies ein Brandrisiko darstellt. Mit Öl verschmutzte Wäschestücke können sich selbst entzünden, besonders, wenn sie einer Wärmequelle wie einem Wäschetrockner ausgesetzt werden. Die Wäschestücke werden erwärmt, was zu einer Oxidationsreaktion mit dem Öl führt wobei die Oxidation weitere Hitze erzeugt. Wenn die Hitze nicht entweichen kann, können die Wäschestücke so heiß werden, dass si sich entzünden. Durch Aufschichten, Stapeln oder Übereinanderliegen von ölverschmutzten Wäschestücken kann die Wärme nicht entweichen und dies führt zu einem Brandrisiko. Wenn unbedingt Wäsche, die mit Gemüse- oder Speiseöl oder mit Haarpflegeprodukten verunreinigt ist, im Wäschetrockner getrocknet werden muss, dann sollte sie zunächst mit besonders viel Waschmittel gewaschen wer den - dies reduziert das Risiko, beseitigt es aber nicht. Sie sollte nicht aus dem Trockner entnommen und in heißem Zustand gestapelt bzw. übereinandergelegt werden.

• Keine Wäsche trocknen, die zuvor mit Benzin, cheschen Lösungsmitteln oder anderen brennbaren oder explosiven Substanzen gereinigt, gewaschen, eingeweicht oder ver schmutzt worden ist. Leichtentzündliche Stoffe, die häufig im häuslichen Umfeld verwendet werden sind: Speiseöl, Aceton, Spiritus, Petroleum, Fleckenentferner, Terpentin, Wachse und Wachs-Entferner. Stellen Sie sicher, dass solche Wäschestücke in heißem Wasser mit einer zusät zlichen Menge an Waschmittel gewaschen worden sind, bevor sie im Trockner getrocknet werden.

• Im Trockner darf keine Wäsche getrocknet werden, die Schaumgummi (auch LatexSchaum genannt) oder ähnlich strukturierte gummiartige Materialien enthalten. Schaumstoff-Materialien können, wenn sie erhitzt werden, durch Selbstentzündung Brände auslösen.

• Weichspüler oder ähnliche antistatische Produkte dürfen nicht in einem Wäschetrockner benutzt werden, es sei denn, die Verwendung ist vom Hersteller des Weichspüler-Produktes ausdrücklich