Hotpoint-Ariston AQM9D 29 U User manual

Instructions for installation and use

 This symbol reminds you to read this instruction manual.

English,1

Русский, 13

AQUALTIS

UKCIS

Укра¿нська,27

Contents

Installation, 2-3

Unpacking and levelling Connecting the electricity and water supplies Technical data

Description of the machine, 4-5

Touch control panel

How to run a wash cycle or a drying cycle, 6

Wash cycles and options, 7

Table of wash cycles Wash options

WASHER-DRYER

AQM9D 29 U

Detergents and laundry, 8

Detergent Preparing the laundry Washing recommendations Load balancing system

Precautions and advice, 9

General safety Disposal Opening the porthole door manually

Care and maintenance, 10

Cutting off the water and electricity supplies Cleaning the machine Cleaning the detergent dispenser drawer Caring for your appliance drum Cleaning the pump Checking the water inlet hose

Trouble shooting, 11

Assistance, 12

Installation

 This instruction manual should be kept in a safe place for future reference. If the washer dryer is sold, given away or moved, please ensure the manual is kept with the machine, so that the new owner may benefit from the advice contained within it.  Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.  Inside the pack containing this manual, you will also find the guarantee and all the details necessary for installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging from the washer dryer, make sure it has not been damaged during transportation. If it has been damaged, contact the retailer and do not proceed any further with the installation process.

2. Remove the 4 protective screws (used during transportation) and the corresponding spacer, located on the rear part of the appliance (see figure).

 If the appliance is levelled correctly, it will be more stable and much less likely to cause vibrations and noise while it is operating, particularly during the spin cycle.  If it is placed on carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the washer dryer.

Connecting the electricity and water supplies

Connecting the water inlet hose

 Before connecting the inlet hose to the water supply, run the water until it is perfectly clear.

1. Connect the inlet hose to the machine by screwing it onto the cold water inlet of the appliance, which is situated on the top righthand side of the rear part of the appliance (see figure).

2. Connect the inlet hose by screwing it to a cold water tab using a 3/4 gas threaded connection (see figure).

3. Close off the holes using the plastic plugs supplied in the pack.

4. Keep all the parts in a safe place; they will be needed again if the washer dryer is moved to another location, to prevent the inside of the appliance being damaged.  Packaging materials should not be used as toys for children.

Levelling

1. Place the washer dryer on a flat sturdy floor, without resting it up against walls or cabinets.

2. If the floor is uneven, the front feet of the machine may be adjusted until it reaches a horizontal position (the angle of inclination must not exceed 2 degrees).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the values indicated in the Technical data table (see next

page).

 If the inlet hose is not long enough, contact a specialised shop or an authorised technician.

 Never use second-hand or old inlet hoses; use the products supplied with the machine.

Connecting the drain hose

65 - 100 cm

Connect the drain hose to drain duct piping or a wall drain located between 65 and 100 cm above the floor, making sure it is not bent at all.

Alternatively, rest the drain hose on the side of a washbasin or bathtub, fastening the duct supplied to the tap (see

figure).

The free end of the hose should not be underwater.

 Do not use extension cords or multiple sockets.

 The cable should not be bent or compressed.

 The power supply cable and plug must only be

replaced by authorised technicians.

Warning! The company shall not be held responsible in the event that these regulations are not respected.

 We advise against the use of hose extensions; if it is absolutely necessary, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity socket, make sure that:

 the socket is earthed and complies with all applicable

laws;

 the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical data table (see opposite);

 the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

 the socket is compatible with the plug of the

appliance. If this is not the case, have the socket or the plug replaced.

 The machine must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to rain, storms and other weather conditions.

 The mains socket must remain within easy reach after the washing machine has been installed.

Technical data

Model

Dimensions

Capacity

Electrical

connections

Water connections

Spin speed

Energy rated programmes

according to regulation EN 50229

AQM9D 29 U

width 59,5 cm height 85 cm depth 64,5 cm

from 1to 9 kg for wash programme from 1 to 6 kg for the drying programme

please refer to the technical data plate fixed to the machine

maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capacity 62 litres

up to 1200 rotations per minute

Wash: programme ; temperature 60°C; using a load of 9 kg. Drying: first drying cycle performed with a 3 kg load, by selecting the drying level "IRON"; Second drying cycle performed with a 6 kg load, selecting the maximum drying level "EXTRA".

This appliance conforms to the following EC Directives:

- 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequent modifications

- 2006/95/EC (Low Voltage)

- 2002/96/EC

Description of the machine

PORTHOLE DOOR

PORTHOLE DOOR HANDLE

KICK STRIP

PORTHOLE DOOR

ADJUSTABLE FEET

Always use the handle to open the porthole door (see

figure).

CONTROL PANEL

washing additives compartment: for fabric softener or liquid additives. We recommend that the maximum level indicated by the grille is not exceeded, and that concentrated fabric softeners are diluted.

TOUCH CONTROL PANEL

To adjust the settings, gently press the icon inside the sensitive (touch control) area as illustrated in the figure.

DETERGENT DISPENSER DRAWER

The detergent dispenser drawer is located inside the machine and can be accessed by opening the door. For more information on detergent measures, please refer to the chapter entitled

Detergents and laundry.

Note: stick the label showing the wash cycle descriptions and options on the front of the detergent dispenser drawer. You will find the sticker in the pack containing this manual.

1. pre-wash compartment: use powder detergent.

2. main wash compartment: use powder or liquid detergent. If using the latter type of detergent, we recommend it is poured into the drawer immediately before you start the washerdryer.

Standby mode

This washer-dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected. Press the ON-OFF for the machine to start up again.

CHANGE LANGUAGE

The first time the machine is switched on, the first language will flash on the display. The " ", "OK" and "V" symbols will appear on the display, in line with the 3 buttons on the righthand side. The languages change automatically every 3"; alternatively, they can be changed by pressing the buttons next to the " language, which will be set after 2". If no buttons are pressed, the automatic language change will begin again after 30".

The language may only be changed while the machine is switched off.

Press and hold the temperature +spin +delayed start

flashes on the display. Press the buttons next to the " " and "V" symbols to change the language. Use the button next to the "OK" symbol to confirm the language, which will be set after 2". If no buttons are pressed, the language set previously will be displayed after 30". Switch on the machine.

" and "V" symbols. Use the "OK" button to confirm the

buttons for 5''; a short beep sounds and the set language

button briefly and wait

Touch control panel

WASH CYCLE

SELECTOR knob

TEMPERATURE

DISPLAY

SPIN

button

START/PAUSEbutton

with indicator light

ECO

indicator light

WASH CYCLE PHASE

icons

Button withON/OFF indicator light

DRY

Button with ON/OFF indicator light: press this briefly to switch the machine on or off. The green indicator light indicates that the machine is switched on. To switch off the washer-dryer during the wash cycle, press and hold the button for approximately 3 seconds; if the button is pressed briefly or accidentally the machine will not switch off. If the machine is switched off during a wash cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR knob: may be turned in either direction. To select the most suitable wash cycle, please refer to the Table of wash cycles. The knob will not move during the wash cycle.

M1-M2 buttons: press and hold one of the buttons to store a cycle with your own set preferences in the memory of the machine. To recall a previously-stored cycle, press the corresponding button.

DRY button

: press to decrease or exclude drying; the

selected drying level or time will appear on the display (see "How to run a wash cycle or a drying cycle").

TEMPERATURE

button: press to modify or exclude the temperature setting; the value selected will appear on the display above (see How to run a wash cycle or a

drying cycle).

SPIN CYCLE

button: press to modify or exclude the spin cycle; the value selected will appear on the display above (see How to run a wash cycle or a drying cycle).

DELAY TIMER

button: press to set a delayed start for the selected wash cycle; the set delay time will appear on the display above (see How to run a wash

cycle or a drying cycle).

OPTION

buttons

CHILD LOCK button

DELAY TIMER

button

DOOR LOCKED

indicator light

with indicator light

WASH CYCLE PHASE icons: these illuminate to indicate the progress of the wash cycle (Wash Rinse

 Spin/Drain  Drying ). The text



lights up when the cycle is complete. START/PAUSE button with indicator light: when the

green indicator light flashes slowly, press the button to start a wash cycle. Once the cycle has begun the indicator light will remain lit in a fixed manner. To pause the wash cycle, press the button again; the indicator light will flash in an orange colour. If the Door locked

indicator light is switched off, the door may be opened. To start the wash cycle from the point at which it was interrupted, press the button again.

DOOR LOCKED

indicator light: indicates that the porthole door is locked. To open the door, pause the wash cycle (see How to run a wash cycle or a drying cycle).

CHILD LOCK

button with indicator light: to activate or deactivate the control panel lock, press and hold the button for approximately 2 seconds. when the indicator light is illuminated, the control panel is locked. This means it is possible to prevent wash cycles from being modified accidentally, especially where there are children in the home.

ECO indicator light: the

icon lights up when, after altering the washing parameters, an energy saving of at least 10% is made. Furthermore, before the machine enters Standby mode, the icon will light up for a few seconds; when the machine is switched off the estimated energy saving will be around the 80% mark.

OPTION buttons: press to select the available options. The indicator light corresponding to the selected option will remain lit (see How to run a wash cycle or a drying

cycle).

How to run a wash cycle or a drying cycle

WARNING: before you use the washer-dryer for the first

time, run a wash cycle with detergent and no laundry, using the 90° cottons cycle without pre-wash.

1. SWITCH THE MACHINE ON. Press the indicator lights will illuminate for 1 second and the text AQUALTIS will appear on the display; the indicator light corresponding to the manner and the START/PAUSE indicator light will flash.

2. SELECT THE PROGRAMME. Turn the PROGRAMME KNOB left or right, until the required programme has been selected; the name of the programme will appear on the display. A temperature and spin speed is set for each programme; these may be adjusted. The cycle duration will also appear on the display.

3. LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of wash cycles on the following page.

4. MEASURE OUT THE DETERGENT. Pull out the detergent dispenser drawer and pour the detergent into the relevant compartments as described in Description of the machine.

5. CLOSE THE PORTHOLE DOOR.

6. CUSTOMISE THE WASH CYCLE. Use the relevant buttons on the control panel:

Modify the temperature and/or spin speed. The machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most recently-used settings if they are compatible with the selected cycle. The temperature can be decreased by pressing the OFF setting is reached. The spin speed may be progressively reduced by pressing the completely excluded OFF. If these buttons are pressed again, the maximum values are restored.

 Exception: if the Cottons programme is selected, the

temperature can be increased up to a value of 90°C.

Setting the drying cycle The first time the button automatically select the maximum drying cycle which is compatible with the selected wash cycle. Subsequent presses will decrease the drying level and then the drying time, until the cycle is excluded completely ("OFF"). If these buttons are pressed again, the maximum values are restored.

Drying may be set as follows:

A - Based on a set time period: between 20 and 180 minutes. B- Based on the desired laundry dryness level: Iron: suitable for clothes which will need ironing afterwards.

the remaining dampness softens creases, making them easier to remove.

Hanger: ideal for clothes which do not need to be dried fully. Cupboard: suitable for laundry which can be put back in a

cupboard without being ironed. Extra: suitable for garments which need to be dried completely, such as sponges and bathrobes.

If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent table), perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them back in the drum. At this point, follow the instructions provided for a "Drying only" cycle. Repeat this procedure for the remainder of the load.

button will then remain lit in a constant

button, until the cold wash

is pressed, the machine will

button. All the

button, until it is

A cooling-down period is always added to the end of each drying cycle.

Drying only

Use the cycle selector knob to select a drying cycle (

) in accordance with the type of fabric. The desired drying

level or time may also be set using the DRYING button

Setting a delayed start.

To set a delayed start for the selected cycle, press the corresponding button repeatedly until the required delay period has been reached. During the setting procedure, the delay period and the text "Starts in: will be displayed, along with the flashing

indicate the duration of the selected cycle with the text "Ends in: and the cycle duration. Press the DELAYED START button just once to display the delay time set previously. After the countdown has begun, the display will show the text "Starts in: and the delay period. Once the set delay time has elapsed, the machine will begin its cycle and the display will show "Ends in: and the time remaining until the end of the cycle. To remove the delayed start option, press the button until the display shows the text OFF; the

 Press the button to activate the option; the name of the option will then appear on the display and the corresponding indicator light will illuminate.  Press the button again to deactivate the option; the

 If the selected option is not compatible with the selected wash cycle, this incompatibility will be signalled by the flashing of the indicator light and a sound alert (3 beeps); the option will not be activated.  If the selected option is not compatible with another option that has been selected previously, the indicator light corresponding to the first option selected will flash and only the second option will be activated; the indicator light corresponding to the button will remain lit in a constant manner.  The options may affect the recommended load value and/ or the duration of the cycle.

7. START THE PROGRAMME. Press the START/PAUSE button. The corresponding indicator light remains lit in a fixed manner and the porthole door locks (the indicator light illuminates). The icons corresponding to the wash cycle phases will light up during the cycle to indicate which phase is currently in progress. To change a wash cycle once it has already started, pause the washer-dryer by pressing the START/PAUSE button; then select the desired cycle and press the START/PAUSE button again. To open the door during a wash cycle, press the START/PAUSE button; if the DOOR LOCKED door. Press the START/PAUSE button again to restart the wash cycle from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated by the illuminated text END. The porthole door may be opened immediately. If the START/PAUSE indicator light is flashing, press the button to end the cycle. Open the door, unload the laundry and switch off the machine.

 If you wish to cancel a cycle which has already begun, press and hold the

symbol. After the delayed start has been set, the

symbol will remain fixed on the display, which will also

symbol will disappear.

Modify the cycle settings.

name of the option will then appear on the display followed by the text OFF, and the corresponding indicator light will switch off.

DOOR LOCKED

indicator light is switched off you may open the

button until the cycle stops and the machine switches off.

- -

Wash cycles and options

Table of wash cycles

Icon Description of the wash cycle

Cottons wash cycles Cotton with pre-wash

(Add detergent to the relevant compartment).

Cotton (1): Cotton (2): heavily soiled whites and delicate colours.

Coloured Cotton (3) 40° 1200

Special wash cycles Steam Refresh* (see next page) Baby: heavily soiled delicate colours

Mix 30': to refresh lightly soiled garments quickly (not suitable for

wool, silk and clothes which require washing by hand)

Durable Synthetics 60° 800

Silk: for garments in silk and viscose, lingerie.

Wool:

Drying Cycles

Wash & dry

Cotton dry

Synthetics dry

Wool dry

Partials cycles

Rinse - 1200 Spin - 1200 Drain - 0 - - - - 9

heavily soiled whites and resistant colours.

for wool, cashmere, etc.

Max.

temp.

(°C)

90° 1200 60°

(Max. 90°)

40° 1200

40° 800 30° 800

30° 0 - -

40° 800

30° 1200

Max.

speed

- - - - - - 1,5

- -

(rpm)

1200

Drying

lll l

Detergent and

additives

Pre-

Was h

wash

- - - 6

- - - 4

- - - 1,5

- -

- - - 9

Fabric

softener

Max.

load

(kg)

9 9

3,5

4 2 2

Cycle

duration

(*) The duration of the wash cycles can be checked

on the display.

(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value will then be shown on the display.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle

2) Long wash cycle for cottons: set wash cycle

3) Short wash cycle for cottons: set wash cycle

with a temperature of 40°C.

with a temperature of 60°C.

Time Saver

Wash options

Steam Hygiene

This option enhances washing performance by generating steam during the wash cycle that eliminates any bacteria from fibres while treating them at the same time. Place the laundry in the drum, choose a compatible programme and select option "  The steam generated during washer dryer operation may cause the porthole door to become hazy.

 It cannot be used in conjunction with , (90°C), ,

, , , , , , , , , .

Extra rinse

By selecting this option, the efficiency of the rinse is increased and optimal residual detergent removal is guaranteed. It is particularly useful for skin which is sensitive to detergents. We recommend this option is used with a full load of washing, or when a large amount of detergent is required.

 It cannot be used in conjunction with

, , , .

, , , ,

If you select this option, the wash cycle duration will be reduced by 30%-50%, depending on the selected cycle, thereby guaranteeing simultaneous water and energy saving. Use this cycle for lightly soiled garments.  It cannot be used in conjunction with

, , , , ,

, , , , , .

Easy Iron

By selecting this option, the wash and spin cycles will be modified in order to reduce the formation of creases.

At the end of the cycle the washing machine drum will rotate slowly; the Easy Iron and START/

PAUSE indicator lights will flash. To end the cycle press the START/PAUSE button or the Easy Iron button. For the Silk

wash cycle, the machine will end the cycle while the laundry is soaking and the Easy Iron indicator light will flash. To drain the water so that the laundry may be removed, press the START/PAUSE button or the Easy Iron button.

 It cannot be used in conjunction with

, , , , ,

, , , , .

Note: If you also want to run the drying cycle, this option is enabled only if combined with level Iron.

Detergents and laundry

Detergent

The type and quantity of detergent required depend on the type of fabric you are washing (cotton, wool, silk, etc.), as well as its colour, the washing temperature, the level of soiling and the hardness of the water in the area. Measuring out the detergent carefully will avoid wastage and help to protect the environment: although they are biodegradable, detergents still contain ingredients which alter the balance of nature. We recommend the following:  use powder detergents for white cotton garments and

pre-washing.

 use liquid detergents for delicate cotton garments and

for all low-temperature wash cycles.  use gentle liquid detergents for wool and silk garments. The detergent should be poured into the relevant compartment - or the dispenser placed directly inside the drum - before the wash cycle begins. In the latter case, it will not be possible to select the Cottons with pre-wash cycle.  Do not use hand washing detergents because these create too much foam.

Preparing the laundry

 Shake out the garments before loading them into the

machine.  Divide the laundry according fabric type (symbol on the

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;  Empty all pockets and check the buttons;  Do not exceed the values listed in the Table of wash

cycles, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillowcase 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

1 pair of jeans 400-500 g

1 shirt 150-200 g

Washing recommendations

* Steam Refresh

This programme refreshes garments by removing bad odours and relaxing the fibres (1.5 kg, roughly 3 items). Insert dry items only (that are not dirty) and select programme " cycle is completed, so we recommend hanging them to dry. The " Moreover, with the "Steam Perfume" laundry balls, your favourite perfume can be added to your laundry. Place a few drops of perfume on the sponge contained inside the laundry ball, close it and insert it into the drum together with the laundry. Then launch the specific programme " be relaxed and fragrant.

 Not recommended for wool or silk garments.  Do not add too much perfume to the sponge in order

to avoid it dripping.  Do not add softeners or detergents.

". The garments will be damp once the

" programme makes ironing easier.

". At the end of the cycle, garments will

Baby: use the special Baby the remove the soiling typically caused by babies, while removing all traces of detergent from nappies in order to prevent the delicate skin of babies from suffering allergic reactions. The cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect of special disinfecting additives added to the detergent. At the end of the wash cycle, the machine will slowly rotate the drum; to end the cycle press the START/PAUSE button. Silk: use the special Silk garments. We recommend the use of special detergent which has been designed to wash delicate clothes. Curtains: use the Silk and place them in a pillow case or mesh bag. Wool: Hotpoint/Ariston is the only washer dryer brand to have been awarded the prestigious Woolmark Platinum Care endorsement (M.0508) by the Woolmark Company, which means that all woollen garments may be washed in the washer dryer, even those which state hand wash only used to wash all woollen garments in the washer dryer while guaranteeing optimum performance.

Wash & Dry

soiled garments quickly. This cycle may be used to wash and dry a laundry load of up to 1 kg in just 60 minutes. To achieve optimum results, use liquid detergent and pretreat cuffs, collars and stains.

on the label. The Wool wash cycle can be

was designed to wash and dry lightly

wash cycle to remove

wash cycle to wash all silk

wash cycle. Fold curtains

Load balancing system

Before every spin cycle, to avoid excessive vibrations before every spin and to distribute the load in a uniform manner, the drum rotates continuously at a speed which is slightly greater than the washing rotation speed. If, after several attempts, the load is not balanced correctly, the machine spins at a reduced spin speed. If the load is excessively unbalanced, the washer dryer performs the distribution process instead of spinning. To encourage improved load distribution and balance, we recommend small and large garments are mixed in the load.

Precautions and tips

 The machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully.

General safety

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.  Do not dry unwashed items in the tumble dryer.  Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer.  Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer.  Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.  The final part of a tumble dryer cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged. WARNING: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is

dissipated.  This appliance was designed for domestic use only.  Do not touch the machine when barefoot or with wet

or damp hands or feet.  Do not pull on the power supply cable when

unplugging the appliance from the electricity socket.

Hold the plug and pull.  Do not touch the drained water as it may reach

extremely high temperatures.  Never force the porthole door. This could damage the

safety lock mechanism designed to prevent

accidental opening.  If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.  Always keep children well away from the appliance

while it is operating.  If it must be moved, proceed with the help of two or

three people and handle it with the utmost care.

Never try to do this alone, because the appliance is

very heavy.  Before loading laundry into the washer dryer, make

sure the drum is empty.  During the drying phase, the door tends to get

quite hot.  Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

 Do not use the appliance to dry foam rubber or

similar elastomers.

 Make sure that the water tap is turned on during

the drying cycles.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that household appliances should not be disposed of using the normal solid urban waste cycle. Exhausted appliances should be collected separately in order to optimise the cost of re-using and recycling the materials inside the machine, while preventing potential damage to the atmosphere and to public health. The crossed-out dustbin is marked on all products to remind the owner of their obligations regarding separated waste collection. For more information relating to the correct disposal of household appliances, owners should contact their local authorities or appliance dealer.

Opening the porthole door manually

In the event that it is not possible to open the porthole door due to a powercut, and if you wish to remove the laundry, proceed as follows:

1. remove the plug from the electrical socket.

2. make sure the water level inside the machine is lower than the door opening; if it is not, remove excess water using the drain hose, collecting it in a bucket as indicated in the figure.

3. remove the cover panel on the lower front part of the washer dryer (see overleaf).

4. pull outwards using the tab as indicated in the figure, until the plastic tie-rod is freed from its stop position; pull downwards until you hear a click, which indicates that the door is now unlocked.

5. open the door; if this is still not possible repeat the procedure.

6. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

Care and maintenance

Cutting off the water and electricity supplies

 Turn off the water tap after every wash cycle. This will

limit wear on the hydraulic system in the machine and help to prevent leaks.

 Unplug the appliance when cleaning it and during all

maintenance work.

Cleaning the machine

The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

To remove the drawer, press lever (1) and pull the drawer outwards (2) (see figure). Wash it under running water; this procedure should be repeated frequently.

To access the pre-chamber:

1. take off the cover panel on the front of the machine by first pressing it in the centre and then pushing downwards on both sides until you can remove it (see

figures);

2. position a container so that it will collect the water which flows out (approximately 1.5 l) (see figure);

3. unscrew the lid by rotating it in an anticlockwise direction (see figure);

Caring for your appliance drum

 Always leave the door ajar to prevent unpleasant

odours from forming.

Cleaning the pump

The washer dryer is fitted with a self-cleaning pump which does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the protective pre-chamber at the base of the pump.

 Make sure the wash cycle has finished and unplug the appliance.

4. clean the inside thoroughly;

5. screw the lid back on;

6. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any cracks, it should be replaced immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.

Trouble shooting

Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Centre (see Assistance), make sure that the problem cannot be not solved easily using the following list.

Problem:

The washer-dryer does not switch on.

The wash cycle does not start.

The washer-dryer does not fill with water.

The washer-dryer door remains locked.

The machine continuously fills with water and drains.

The washer-dryer does not drain or spin.

The machine vibrates a lot during the spin cycle.

The washer-dryer leaks.

The icons corresponding to the Phase in progress flash rapidly at the same time as the ON/OFF

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or not enough to make contact.  There is no power in the house.

 The door is not closed properly.  The START/PAUSE button has not been pressed.  The water tap has not been opened.  A delayed start has been set.

 The water inlet hose is not connected to the tap.  The hose is bent.  The water tap has not been opened.  There is no water supply in the house.  The pressure is too low.  The START/PAUSE button has not been pressed.

 If you have selected the Baby

the wash cycle has finished the machine will slowly rotate the drum; to end the cycle press the START/PAUSE button or the Easy iron you have selected the Silk while the laundry is soaking; to drain the water so that the laundry may be removed, press the START/PAUSE button or the Easy iron

 The drain hose is not fitted at a height between 65 and 100 cm from the

floor (see Installation).  The free end of the hose is under water (see Installation).  If the dwelling is on one of the upper floors of a building, there may be

problems relating to water drainage, causing the washer-dryer to fill with

water and drain continuously. Special anti-draining valves are available in

shops and help to prevent this inconvenience.  The wall drainage system is not fitted with a breather pipe.

 The wash cycle does not include draining: Some wash cycles require the

drain phase to be started manually (see Wash cycles and options).  The drain hose is bent (see Installation).  The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).  The machine is not level (see Installation ).  The machine is trapped between cabinets and walls (see Installation).  The load is unbalanced (see Detergents and laundry).

 The water inlet hose is not screwed on properly (see Installation).  The detergent dispenser is blocked (to clean it, see Care and maintenance).  The drain hose is not fixed in place properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again. If the problem persists, contact the Technical

Assistance Service.

 cycle or the Easy iron  option, when

 wash cycle, the machine will end the cycle

indicator light.

 button. If

 button.

There is too much foam.

The washer-dryer door remains locked.

The washer-dryer does not dry.



Note: To exit Demo mode, press and hold the two ON/OFF and START/PAUSE buttons simultaneously for 3 seconds.

 The detergent is not suitable for machine washing (it should display the text

for washer-dryers or hand and machine wash, or the like).  Too much detergent was used.

 Perform the manual unlocking procedure (see Precautions and tips).

 The appliance is not plugged into the socket, or not enough to make contact.  There has been a power failure.  The appliance door is not shut properly.  A DELAY TIMER has been set.  DRYING is in the OFF position.

Assistance

Before calling for Assistance:

 Check whether you can solve the problem by yourself (see Trouble shooting);  Restart the wash cycle to check whether the problem has been solved;  If it has not, contact the Authorised Technical Assistance Service.

 If the washer-dryer has been installed or used incorrectly, you will have to pay for the call-out service.  Always request the assistance of authorised technicians.

Please have the following information to hand:

 the type of problem;  the appliance model (Mod.);  the serial number (S/N). The above information can be found on the data plate located on the appliance itself.

+ 28 hidden pages