Hotpoint-ariston 7HKRC 640 X User Manual [ru]

Operating Instructions

HOB

English,1

Русский, 14

7HKRC 640 B RU/HA 7HKRC 640 X RU/HA 7HKRC 641 D X RU/HA

Contents

Installation, 2-4

Positioning Electrical connection

Description of the appliance, 5-6

Control panel Extendable cooking zones

Start-up and use, 7-10

Switching on the hob Switching on the cooking zones Switching off the cooking zones Power function Heating elements Programming the cooking duration Timer Control panel lock Switching off the hob Demo mode Practical advice on using the appliance Safety devices Practical cooking advice

Precautions and tips, 11

General safety Disposal

Care and maintenance, 12

Switching the appliance off Cleaning the appliance Disassembling the hob

Technical description of the models, 13

Installation

 Before operating your new appliance please read

this instruction booklet carefully. It contains important information concerning the safe operation, installation and maintenance of the appliance.

 Please keep these operating instructions for future

reference. Pass them on to any new owners of the appliance.

Positioning

 Keep all packaging material out of the reach of

children. It may present a choking or suffocation hazard (see Precautions and tips).

 The appliance must be installed by a qualified

professional in accordance with the instructions provided. Incorrect installation may cause harm to people and animals or may damage property.

Built-in appliance

Use a suitable cabinet to ensure that the appliance functions properly.  The supporting surface must be heat-resistant up

to a temperature of approximately 100°C.

 If the appliance is to be installed above an oven,

the oven must be equipped with a forced ventilation cooling system.

 Avoid installing the hob above a dishwasher: if

this cannot be avoided, place a waterproof separation device between the two appliances.

 Depending on the hob you want to install, the

cabinet must have the following dimensions (see figure):

590

5 mm

UNDERSIDE OF HOB

min. 20 mm

COMPARTMENT

min. 40 mm

min. 20 mm

FAN-ASSISTED

OVEN

min. 40 mm

FRONT SIDE OF HOB

SUPPORTING SURFACE

560 +/- 1

490 +/- 1

Ventilation

To allow adequate ventilation and to avoid overheating of the surrounding surfaces the hob should be positioned as follows:

At a minimum distance of 40 mm from the back

panel.

So that a minimum distance of 20 mm is

maintained between the installation cavity and the cabinet underneath.

 Kitchen cabinets adjacent to the appliance and

taller than the top of the hob must be at least 600 mm from the edge of

the hob.

Fixing

The appliance must be installed on a perfectly level

supporting surface. Any deformities caused by improper fixing could affect the features and operation of the hob.

The thickness of the supporting surface

taken into account when choosing

the length of the

should be

screws for the fixing hooks:  30 mm thick: 17.5 mm screws 40 mm thick: 7.5 mm screws

Fix the hob as follows:

1. Use short flat-bottomed screws to fix the 4 alignment springs in the holes provided at the central point of each side of the hob.

Place the hob in the cavity, make sure it is in a

central position and push down on the whole perimeter until the hob is stuck to the supporting surface.

3. For hobs with raised sides: After inserting the hob into its cavity, insert the 4 fixing hooks (each has its own pin)

into the lower edges of the hob, using the long pointed screws to fix them in place, until the glass is stuck to the supporting surface.

 The screws for the alignment springs must remain

accessible.

 In order to adhere to safety standards, the

appliance must not come into contact with electrical parts once it has been installed.

 All parts which ensure the safe operation of the

appliance must not be removable without the aid of a tool.

Electrical connection

 The electrical connection for the hob and for any

built-in oven must be carried out separately, both for safety purposes and to make extracting the oven easier.

Terminal board

On the lower part of the

UNDERSIDE OF HOB

appliance there is a connection box for the different types of electricity supply (the picture is only an indication and is not an exact representation of the purchased model).

Single-phase connection

The hob is equipped with a pre-connected electricity supply cable, which is designed for single-phase connection. Connect the wires in accordance with the instructions given in the following table and diagrams:

Voltage an d

mains freq uenc y

230-240V 1+N ~ 220-240V 1+N ~

50/60 Hz

Electrical cable Wire connection

: yellow/green; N: the t wo blu e wires together L: brown and black together

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

 400V - 2+N ~ 50/60 Hz  220-240V 3 ~ 50/60 Hz  230-240V 3 ~ 50/60 Hz

 400V - 2+2N ~ 50/60 Hz

Separate the wires and connect them in accordance with the instructions given in the following table and diagrams:

Voltage and

mains frequency

400V - 2+N ~

50/60 Hz

230-240V 3 ~ 220-240V 3 ~

50/60Hz

400V - 2+2N ~

50/60 Hz

Electrical cable Wire connection

: yellow/green;

N: the two blue wires together

L1: black

L2: brown

: yellow/green;

N1: blue

N2: blue

L1: black

L2: brown

If the mains supply corresponds with one of the following: Voltage and mains frequency  400V 3 - N ~ 50/60 Hz proceed as follows:

 The cable provided is not suitable for the following

types of installation.

1. Use a suitable supply cable, H05RR-F or higher, with the right dimensions (cable cross section: 25 mm).

2. To open the terminal board, use a screwdriver as a lever under the side tabs of the cover (see Terminal board picture).

3. Loosen the cable clamp screw and the terminal board screws in accordance with the type of

connection required and position the connection supports as shown in the following table and diagrams.

4. Position the wires in accordance with the information given in the following table and diagrams and connect the appliance by tightening all the screws for the springs as much as possible.

Voltage and

mains frequenc y

400V 3-N ~

50/60 Hz

Electrical connections Terminal board

Three-phase 4 00

5. Secure the power supply cable by fastening the cable clamp screw, then put the cover back on.

Phase Phase Phase

Earth

Neutral

connection support

U-bolt

Three-phase 400

Connecting the electricity supply cable to the mains

If the appliance is being connected directly to the electricity mains an omnipolar switch must be installed with a minimum opening of 3 mm between contacts.

 The installer must ensure that the correct electrical

connection has been made and that it is fully compliant with safety regulations.

Before connecting the appliance to the power supply, make sure that:  The appliance is earthed and the plug is

compliant with the law.

 The socket can withstand the maximum power of

the appliance, which is indicated on the data plate located on the appliance itself.

 The voltage falls within the range of values

indicated on the data plate.

 The socket is compatible with the plug of the

appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets.

 Once the appliance has been installed, the power

supply cable and the electrical socket must be easily accessible.

 The cable must not be bent or compressed.

 The cable must be checked regularly and replaced

by authorised technicians only.

 The manufacturer declines any liability should

these safety measures not be observed.

Description of the

appliance

Control panel

The control panel described in this manual is only a representative example: it may not exactly match the panel on your appliance.

TIMER*

indicator light

POWER and

RESIDUAL HEAT

indicators

INCREASE

POWER button

COOKING ZONE SELECTED indicator light

COOKING ZONE SELECTOR buttons

REDUCE POWER

button

PROGRAMME TIMER*

display

COOKING ZONE PROGRAMMED*

indicator light

ON/OFF

button

ON/OFF

indicator light

CONTROLS LOCKED

indicator light

CONTROL PANEL LOCK button

PROGRAMME TIMER* button

 INCREASE POWER button switches on the

hotplate and controls the power (see Start-up and use).

 REDUCE POWER button controls the power and

switches off the hotplate (see Start-up and use).

 COOKING ZONE SELECTOR button shows a

particular cooking zone has been selected and therefore various adjustments are possible.

 COOKING ZONE SELECTOR button is used to

select the desired cooking zone.

 POWER indicator provides a visual display for the

current heat level.

 ON/OFF button switches the appliance on and off.

 ON/OFF indicator light shows whether the

appliance is on or off.

 PROGRAMME TIMER* button controls the

cooking programme times (see Start-up and use).

Only available in certain models.

 PROGRAMME TIMER* display shows which

programme has been selected (see Start-up and use).

 COOKING

ZONE PROGRAMMED* indicator lights show which cooking zones are being used during a cooking programme (see Start-up and use).

 CONTROL PANEL LOCK button prevents

accidental changes to the hob settings (see Start- up and use).

 CONTROL PANEL LOCK indicator light shows

the control panel has been locked (see Start-up and use).

 TIMER* indicator light shows that the timer has

been activated

 This product complies with the requirements of the latest European Directive on the limitation of power consumption of the standby mode. If no operations are carried out for a period of 2 minutes, after the residual heat indicator lights turn off and the fan stops (if present), the appliance automatically switches to the off mode. The appliance resumes the operating mode once the ON/OFF button is pressed.

Extendable cooking zones

Certain models are fitted with extendable cooking zones. A list of controls is given below (these controls are only present in models with the extendable cooking zone option).

Circular extendable hotplate

DOUBLE HOTPLATE ON

indicator light

DOUBLE HOTPLATE ON

button

 DOUBLE HOTPLATE ON button switches on the

double hotplate (see Start-up and use).

 DOUBLE HOTPLATE ON indicator light shows

the double hotplate has been switched on.

Start-up and use

 The glue applied on the gaskets leaves traces of

grease on the glass. Before using the appliance, we recommend you remove these with a special nonabrasive cleaning product. During the first few hours of use there may be a smell of rubber which will disappear very quickly.

 A few seconds after the hob is connected to the

electricity supply, a buzzer will sound. The hob may now be switched on.

 If the - or + button is pressed for an extended

period of time, the display scrolls quickly though the power levels and timer minutes.

Switching on the hob

To switch the hob on, press and hold the button

for approximately one second.

Switching on the cooking zones

Each cooking zone is controlled using a selector

button

and a power adjustment device

Switching off the cooking zones

To switch off a cooking zone, select it using the

corresponding selector button

 Press the

will progressively decrease until it is switched off.

- button: the power of the cooking zone

and:

Heating elements

Two types of heating element may be installed, depending on the appliance model: halogen and radiant elements. Halogen elements emit heat via radiation from the halogen lamps they contain. They have similar properties to gas burners: they are easy to control and reach set temperatures quickly, allowing you to see the power level instantly. Radiant elements consist of a series of coils which allow heat to be distributed evenly at the base of the cookware, so that all slow-flame cooking may be performed successfully, for example stews, sauces or reheated dishes.

Programming the cooking duration

consisting of a double

 To begin operating a cooking zone, press the

corresponding control button and set the desired power level (between 0 and 9) using the buttons

- and + button.

- and +.

Power function

The power function for the cooking zones may be used to shorten heating-up times. Activate and set

the power level for the desired cooking zone

described in the previous paragraph. Press and hold the selector button corresponding to the desired

cooking zone

display, the power level indicator, will alternately show the letter P and the power level set previously until the desired power level has been reached. Once this level has been reached, the display will revert to showing the set power level. To deactivate this function, press and hold  for at least 2 seconds - the selector button corresponding to the

cooking zone on which the

activated; alternatively, select a different power level

using the buttons

for at least 2 seconds. The

function has been

- and +.

 All the cooking zones may be programmed simultaneously, for a duration between 1 and 99 minutes.

1. Select the cooking zone using the corresponding selector button.

2. Adjust the temperature.

3. Press the

4. Set the cooking duration using the

buttons.

5. Confirm by pressing the

The timer begins counting down immediately. A buzzer sounds for approximately 1 minute and the cooking zone switches off when the set programme has finished. Repeat the above procedure for each hotplate you wish to programme.

Using multiple programmes and the display

If one or more hotplates are programmed, the display will show the data for the hotplate with the least time remaining, and the light corresponding to the position of the hotplate will flash. The lights corresponding to the other hotplates programmed will be switched on.

programming button.

- and +

button.

To display the time remaining for the other

programmed hotplates, press the

repeatedly. The times remaining for each hotplate will be shown in a clockwise order, beginning with the front left hotplate.

Changing the programme

button

Switching off the hob

Press the button to switch the appliance off.

If the control panel lock has been activated, the controls will continue to be locked even after the hob is switched on again. In order to switch the hob on again, you must first remove the lock function.

1. Press the

you wish to change is shown.

2. Use the

3. Confirm by pressing the

To cancel a programme, follow the above

instructions. At step 2, press the

duration decreases progressively until it reaches 0 and switches off. The programme resets and the display exits programming mode.

button repeatedly until the duration

buttons to set the new duration.

button.

- button: the

Timer

The hob must be switched on. The timer can be used to set a duration up to 99 minutes.

1. Press the

indicator light is illuminated.

2. Set the desired duration using the

buttons.

programming button until the timer

- and +

Demo mode

It is possible to set the hob to a demonstration mode where all the controls work normally but the heating elements do not switch on. To activate the demo mode the hob must be switched on, with all the hotplates switched off.

 Press and hold the

simultaneously for 6 seconds. When the 6 seconds have elapsed, the ON/OFF and CONTROLS LOCKED indicator lights will flash for

one second. Release the

press the

 The display will show the text DE and MO and the

hob will be switched off.

 When the hob is switched on again it will be set to

the demo mode.

To exit this mode, follow the procedure described above. The display will show the text DE and OF and the hob will be switched off. When it is next switched on, the hob will function normally.

+ and - buttons

+ and - buttons and

button;

3. Confirm by pressing the

The timer begins counting down immediately. When the time has elapsed, a buzzer will sound (for one minute).

button.

Control panel lock

When the hob is switched on, it is possible to lock the oven controls in order to avoid accidental changes being made to the settings (by children,

during cleaning, etc.). Press the

the control panel: the indicator light above the button will switch on. To use any of the controls (e.g. to stop cooking),

you must switch off this function. Press the

button for a few moments, the indicator light will switch off and the lock function will be removed.

button to lock

Practical advice on using the appliance

To obtain the best results from your hob:  Use pans with a thick, flat base in order to fully

utilise the cooking zone.

 Always use pans with a diameter which is large

enough to cover the hotplate fully, in order to use all the available heat.

 Make sure that the base of the cookware is

always clean and dry, in order to fully utilise and extend the life of both the cooking zones and the cookware.

 Avoid using the same cookware which has been

used on gas burners: the heat concentration on gas burners may distort the base of the pan, causing it not to adhere correctly.

Overheating protection

If the electronic elements overheat, the hob switches

off automatically and

followed by a flashing number. When the temperature has reached a suitable level, this message disappears and the hob may be used again.

F appears on the display,

Safety devices

Pan sensor

Each cooking zone is equipped with a pan sensor device. The hotplate only emits heat when a pan with suitable measurements for the cooking zone is placed on it. If the indicator light is flashing, it may indicate:  An incompatible pan  A pan whose diameter is too small  The pan has been removed from the hotplate.

Residual heat indicators

Each cooking zone is equipped with a residual heat indicator. This indicator signals which cooking zones are still at a high temperature. If the power display

shows possible, for example, to keep a dish warm or melt butter or chocolate. As the cooking zone cools, the

power display will show when the cooking zone has cooled sufficiently.

, the cooking zone is still hot. It is

. The display switches off

Safety switch

The appliance has a safety switch which automatically switches the cooking zones off after they have been in operation for a certain amount of time at a particular power level. When the safety switch has been triggered, the display shows 0. For example: the right rear hotplate is set to 5 and will switch off after 5 hours of continuous operation, while the front left hotplate is set to 2 and will switch off after 8 hours.

Power level

1 9

Maximum operating

time in hours

9 1

Buzzer

This can also indicate several irregularities:  An object (a pan, cutlery, etc.) has been placed

on the control panel for more than 10 seconds.

 Something has been spilt on the control panel.  A button has been pressed for too long. All of the

above situations may cause the buzzer to sound. Remove the cause of the malfunction to stop the buzzer. If the cause of the problem is not removed, the buzzer will keep sounding and the hob will switch off.

+ 19 hidden pages