Hotpoint PC 640T, PC 631 X /HA PL User Manual

PC 640 X /HA PL
PC 631 X /HA PL
PC 640T R /HA PL
PC 640 T X /HA PL

English

Operating Instructions

HOB

Contents

Operating Instructions,1
Warnings,2
Assistance,4
Description of the appliance,5
Installation,7
Start-up and use,11
Precautions and tips,12
Maintenance and care,12
Troubleshooting,13

Polski

Instrukcja obsługi

PŁYTA

Spis treści

Magyar

Használati útmutató

FŐZŐLAP

Tartalomjegyzék

Használati útmutató,1
Figyelmeztetések,3
Szerviz,4
A készülék leírása,6
Üzembe helyezés,21
Bekapcsolás és használat,25
Óvintézkedések és tanácsok,25
Karbantartás és ápolás,26
Hibaelhárítás,26

Instrukcja obsługi,1

Ostrzezenia,2
Serwis Techniczny,4

Opis urządzenia,5

Instalacja,14

Uruchomienie i użytkowanie,18
Zalecenia i środki ostrożności,18

Konserwacja i utrzymanie,19

Anomalie i środki zaradcze,20

Warnings

Ostrzezenia

WARNING: The appliance and its
accessible parts become hot during use.
Care should be taken to avoid touching

heating elements. Children less than 8

years of age shall be kept away unless
continuously supervised. This appliance

can be used by children aged from 8 years

and above and persons with reduced
physical, sensory or mental capabilities
or lack of experience and knowledge
if they have been given supervision
or instruction concerning use of the
appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and
user maintenance shall not be made by
children without supervision.

WARNING: Unattended cooking on a hob
with fat or oil can be dangerous and may

result in re. NEVER try to extinguish a
re with water, but switch off the appliance
and then cover ame e.g. with a lid or a
re blanket.

WARNING: Danger of re: do not store

items on the cooking surfaces.

Never use steam cleaners or pressure
cleaners on the appliance.

UWAGA: To urządzenie oraz jego
dostępne części silnie się rozgrzewają
podczas użytkowania. Należy uważać,
aby nie dotknąć elementów grzejnych.
Nie pozwalać, aby dzieci poniżej 8 roku
życia zbliżały się do urządzenia, jeśli nie
są pod stałym nadzorem dorosłych.
Z niniejszego urządzenia mogą korzystać
dzieci powyżej 8 roku życia i osoby o
ograniczonych zdolnościach zycznych,
zmysłowych bądź umysłowych, jak również
osoby nieposiadające doświadczenia lub
znajomości urządzenia, jeśli znajdują się
one pod nadzorem innych osób lub jeśli
zostały pouczone na temat bezpiecznego
sposobu użycia urządzenia oraz zdają
sobie sprawę ze związanych z nim
zagrożeń. Dzieci nie powinny bawić
się urządzeniem. Prace związane z
czyszczeniem i konserwacją nie mogą
być wykonywane przez dzieci, jeśli nie
są one nadzorowane.

UWAGA: Pozostawienie bez nadzoru na

kuchence tłuszczów i olejów może być
niebezpieczne i może spowodować pożar.
Nie należy NIGDY próbować ugasić
płomieni/pożaru wodą; należy wyłączyć
urządzenie i przykryć płomień np.
pokrywką lub ognioodpornym kocem.

Remove any liquid from the lid before
opening it. Do not close the glass cover (if
present) when the gas burners or electric
hotplates are still hot.

The appliance is not intended to be
operated by means of an external timer
or separate remote control system.

CAUTION: the use of inappropriate hob
guards can cause accidents.

2

UWAGA: Ryzyko pożaru: nie pozostawiać

przedmiotów na powierzchniach
grzejnych.

Nie stosować nigdy oczyszczaczy
parowych lub ciśnieniowych do
czyszczenia urządzenia.

Usunąć ewentualne płyny na pokrywie
przed jej otwarciem. Nie zamykać szklanej
pokrywy (jeśli jest częścią wyposażenia),
jeśli palniki gazowe lub płyta elektryczna
są jeszcze rozgrzane.

Urządzenie nie jest przeznaczone do
włączania przy użyciu zewnętrznego
przekaźnika czasowego lub zdalnego

systemu sterowania.

UWAGA: użycie niewłaściwych
zabezpieczeń płyty może być przyczyną

wypadków.

SOHA ne próbálja meg vízzel eloltani a
tüzet, hanem zárja el a készüléket, és

takarja le a lángot például fedővel vagy
tűzálló takaróval.

FIGYELEM: Tűzveszély! Ne tároljon
semmit a főző felületeken!

A készülék tisztításához soha ne használ-

jon gőztisztítót vagy nagynyomású tisz-

títót.

A fedő kinyitása előtt távolítsa el az
összes folyadékot! Ne csukja be az
üveg fedőt (típustól függően) ha a gáz
égők vagy elektromos főzőmezők még
melegek!

Figyelmeztetések

FIGYELEM: A készülék és annak
hozzáférhető részei a használat közben

rendkívüli módon felmelegedhetnek.

Vigyázzon, hogy nehogy hozzáérjen a
fűtőelemekhez.

Ha a gyermekek nincsenek folyamatos

felügyelet alatt, tartsa távol a 8 éven aluli

gyermekeket.

Ezt a készüléket a 8 éves kort betöltött

gyermekek, valamint a testileg,
érzékszervileg vagy szellemileg

korlátozott, nem hozzáértő, illetve a
terméket nem ismerő személyek csak
megfelelő felügyelet mellett, vagy a

készülék biztonságos használatával

kapcsolatos alapvető utasítások és a

kapcsolódó veszélyek ismeretében

használhatják. Vigyázzon, hogy a

gyermekek ne játsszanak a készülékkel.

A tisztítási és karbantartási műveleteket

gyermekek felügyelet nélkül nem
végezhetik.

A készüléket nem szabad külső
időmérővel vagy különálló távirányító

rendszerrel használni.

FIGYELEM: A főzőlap nem megfelelő

használata balesetet okozhat.

FIGYELEM: A tűzhelyen felügyelet nélkül

otthagyott zsír vagy olaj veszélyes lehet,
és tüzet okozhat.

3

Assistance

Communicating:

• appliance model (Mod.)

• serial number (S/N)

This information is found on the data plate located on the

appliance and/or on the packaging.
! Never use unauthorised technicians and never accept

replacement parts which are not original.

Serwis Techniczny

! Nigdy nie korzystać z usług nieautoryzowanych techników.

Podać:

• Rodzaj usterki;

• Model urządzenia (Mod.)

• Numer seryjny (S/N)
Te ostatnie informacje można znaleźć na tabliczce
znamionowej umieszczonej na urządzeniu.

Szerviz

! Sohase hívjon engedéllyel nem rendelkező szakembert!

Adja meg az alábbiakat:

• az anomália típusa;

• a készülék modellje (Mod.)

• a készülék szériaszáma (S/N)

Az utóbbi információk a készüléken elhelyezett adattáblán
találhatók.

4

Description of the appliance

Opis urządzenia

Overall view

1 Support Grid for COOKWARE
2 GAS BURNERS
3 ELECTRIC HOTPLATE*
4 Electric HOTPLATE INDICATOR LIGHT*
5 Control Knobs for GAS BURNERS
6 Control Knobs for ELECTRIC HOTPLATES*
7 Ignition for GAS BURNERS*
8 SAFETY DEVICES*

• ELECTRIC HOTPLATES may have different diameters

and operate at different power levels. These power

levels may be “normal” or “rapid” (the latter may be

distinguished from the others by a red spot in the middle
of the hotplate).

• The ELECTRIC HOTPLATE INDICATOR LIGHT*

switches on whenever the selector knob is moved from
the ‘off’ position.

• GAS BURNERS differ in size and power. Use the

diameter of the cookware to choose the most appropriate
burner to cook with.

• Control Knobs for GAS BURNERS and ELECTRIC
PLATES* adjust the power or the size of the ame.

• GAS BURNER IGNITION* enables a specic burner to

be lit automatically.

• SAFETY DEVICE* stops the gas ow if the ame is

accidentally extinguished.

Widok ogólny

1 Ruszty do ustawiania NACZYŃ DO GOTOWANIA
2 PALNIKI GAZOWE
3 PŁYTA ELEKTRYCZNA*
4 Kontrolka działania PŁYTY ELEKTRYCZNEJ*
5 Pokrętła sterujące PALNIKÓW GAZOWYCH
6 Pokrętła sterujące PŁYTY ELEKTRYCZNEJ*
7 Świeca zapłonowa PALNIKÓW GAZOWYCH
8 URZĄDZENIE ZABEZPIECZAJĄCE

• PŁYTY ELEKTRYCZNE mogą mieć różne średnice

i charakteryzować się różną mocą: „normalne” lub
“szybkie”; szybkie płyty można rozpoznać dzięki
czerwonemu znakowi umieszczonemu na środku.

• Kontrolka działania PŁYTY ELEKTRYCZNEJ* zapala

się dla każdej pozycji pokrętła z wyjątkiem pozycji
wyłączenia

• PALNIKI GAZOWE posiadają różne wymiary i moce.

Należy wybrać ten palnik, który jest najbardziej
odpowiedni dla średnicy używanego naczynia.

• Pokrętła sterowania palnikami gazowymi oraz PŁYTĄ
ELEKTRYCZNĄ* do regulowania płomienia lub mocy.

• Świeca zapłonowa PALNIKÓW GAZOWYCH* umożliwia

automatyczne zapalenie wybranego palnika.

• URZĄDZENIE ZABEZPIECZAJĄCE* w razie
przypadkowego zgaśnięcia płomienia przerywa dopływ

gazu.

* Only available on certain models.

8

* Tylko w niektórych modelach.

7

2

3

1

4

6

5

5

A készülék leírása

A készülék áttekintése

1 Főzőedénytartó RÁCSOK
2 GÁZÉGŐK
3 ELEKTROMOS FŐZŐLAPOK*
4 ELEKTROMOS FŐZŐLAPOK működését jelző lámpa
5 Gázégő vezérlő TEKERŐGOMBOK
6 FŐZŐLAPOK szabályzógombja
7 GYÚJTÓGYERTYA gázégők
8 BIZTONSÁGI SZERKEZET

• Az ELEKTROMOS FŐZŐLAPOK MŰKÖDÉSÉT JELZŐ
LÁMPA* bekapcsol, ha a választó gombot elforgatja a

kikapcsolt pozícióról.

• Az ELEKTROMOS FŐZŐMEZŐK különböző méretűek
és különböző teljesítményűek lehetnek. A teljesítmény
szint lehet „normál” vagy „gyors” (az utóbbi a főzőmező
közepénél levő piros foltról ismerhető fel.).

• GÁZÉGŐK: Különböző méretűek és teljesítményűek.
Válassza a használni kívánt edény átmérőjének
leginkább megfelelőt.

• A GÁZ ÉGŐ és ELEKTROMOS FŐZŐMEZŐ üzemeltető

gombok* szabályozzák a teljesítményt és a láng
nagyságát.

• GYÚJTÓGYERTYA gázégők: A kiválasztott gázégő

automatikus meggyújtására szolgál.

• BIZTONSÁGI SZERKEZET: A láng véletlen kialvása
esetén a gázellátás kikapcsolására szolgál.

* Csak néhány modellnél

8

7

2

3

1

4

6

6

5

Installation

555 mm

! Before operating your new appliance please read this
instruction booklet carefully. It contains important information
for safe use, installation and care of the appliance.

! Please keep these operating instructions for future reference.
Pass them on to possible new owners of the appliance.

Positioning

! Keep packaging material out of the reach of children. It can
become a choking or suffocation hazard (see Precautions
and tips).

! The appliance must be installed by a qualied professional

according to the instructions provided. Incorrect installation
may cause harm to people and animals or may damage
property.

• Liquid petroleum gas sinks to the oor as it is heavier
than air. Therefore, rooms containing LPG cylinders must

also be equipped with vents to allow gas to escape in

the event of a leak. As a result LPG cylinders, whether

partially or completely full, must not be installed or stored
in rooms or storage areas that are below ground level
(cellars, etc.). It is advisable to keep only the cylinder
being used in the room, positioned so that it is not subject

to heat produced by external sources (ovens, replaces,

stoves, etc. ) which could raise the temperature of the

cylinder above 50°C.

Fitting the appliance

Gas and mixed hobs are manufactured with type X degree
protection against overheating. The following precautions
must be taken when installing the hob:

• Kitchen cabinets adjacent to the appliance and taller than
the top of the hob must be at least 600 mm from the edge

of the hob.

GB

! This unit may be installed and used only in permanently
ventilated rooms in accordance with British Standard

Codes Of Practice: B.S. 6172 / B.S. 5440, Par. 2 and B.S.
6891 Current Editions. The following requirements must

be observed:

• The room must be equipped with an air extraction system

that expels any combustion fumes. This may consist of
a hood or an electric fan that automatically starts each
time the appliance is switched on.

In a chimney stack or branched flue.
(exclusively for cooking appliances)

Directly to
the Outside

• The room must also allow proper air circulation, as air is
needed for combustion to occur normally. The ow of air

must not be less than 2 m3/h per kW of installed power.

The air circulation system may
take air directly from the outside
by means of a pipe with an inner

cross section of at least 100 cm2;

Examples of
ventilation holes
for comburant air.

A

the opening must not be vulnerable
to any type of blockages.

• Hoods must be installed according to their relative

installation instruction manuals and at a minimum

distance of 650 mm from the hob (see gure).

• Place the wall cabinets adjacent to the hood at a minimum
height of 420 mm from the hob (see gure).

If the hob is installed beneath a wall
cabinet, the latter must be situated

600mm min.

650mm min.

at a minimum of 700 mm above

the hob.

420mm min.

• The installation cavity should have the dimensions
indicated in the gure.

Fastening hooks are provided, allowing you to fasten

the hob to tops that are between 20 and 40 mm thick.

To ensure the hob is securely fastened to the top, we
recommend you use all the hooks provided.

55 mm

475 mm

Adjacent
Room

Room to be
Vented

Enlarging the ventilation slot
between window and floor.

The system can also provide the air
needed for combustion indirectly,

i.e. from adjacent rooms tted with

air circulation tubes as described
above. However, these rooms must
not be communal rooms, bedrooms

or rooms that may present a re

hazard.

7

Hook fastening diagram

GB

frequency indicated on the data plate (this is located on the
lower part of the appliance). The earth wire in the cable has a
green and yellow cover. If the appliance is to be installed above
a built-in electric oven, the electrical connection of the hob and
the oven must be carried out separately, both for electrical
safety purposes and to make extracting the oven easier.

Hooking position Hooking position
for top H=20mm for top H=30mm

Front

Hooking position Back
for top H=40mm

! Use the hooks contained in the “accessory pack”.

• Where the hob is not installed over a built-in oven, a

wooden panel must be installed as insulation. This must

be placed at a minimum distance of 20 mm from the lower

part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet
must be removed. It is advisable to install the oven so that it

rests on two strips of wood, or on a completely at surface
with an opening of at least 45 x 560 mm (see diagrams).

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load
indicated on the data plate.
The appliance must be directly connected to the mains
using an omnipolar circuit-breaker with a minimum contact
opening of 3 mm installed between the appliance and the
mains. The circuit-breaker must be suitable for the charge
indicated and must comply with current electrical regulations
(the earthing wire must not be interrupted by the circuit­breaker). The supply cable must not come into contact with

surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical
connection has been made and that it is compliant with
safety regulations.
Before connecting to the power supply, make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate.

• The voltage is in the range between the values indicated

on the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.

45 mm.

560 mm.

Where a hob is installed above an oven without a forced
ventilation cooling system, adequate ventilation must be
provided inside the cabinet by means of air holes through

which air can pass (see gure).

Electrical connection

Hobs equipped with a three-pole power supply cable are
designed to operate with alternating current at the voltage and

! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these safety
measures not be observed.

Gas connection

The appliance should be connected to the main gas supply
or to a gas cylinder in compliance with current national
regulations. Before carrying out the connection, make sure
the cooker is compatible with the gas supply you wish to
use. If this is not the case, follow the instructions indicated

in the paragraph “Adapting to different types of gas.”

When using liquid gas from a cylinder, install a pressure
regulator which complies with current national regulations.

! Check that the pressure of the gas supply is consistent with the

values indicated in Table 1 (“Burner and nozzle specications”).

This will ensure the safe operation and longevity of your

appliance while maintaining efcient energy consumption.

8

Connection with a rigid pipe (copper or steel)

! Connection to the gas system must be carried out in such a
way as not to place any strain of any kind on the appliance.

There is an adjustable L-shaped pipe tting on the appliance
supply ramp and this is tted with a seal in order to prevent

leaks. The seal must always be replaced after rotating the

pipe tting (seal provided with appliance). The gas supply
pipe tting is a threaded 1/2 gas cylindrical male attachment.

Connecting a exible jointless stainless steel pipe to
a threaded attachment

The gas supply pipe tting is a threaded 1/2 gas cylindrical

male attachment.
These pipes must be installed so that they are never longer

than 2000 mm when fully extended. Once connection has
been carried out, make sure that the exible metal pipe

does not touch any moving parts and is not compressed.

! Only use pipes and seals that comply with current national
regulations.

• Adjusting the burners’ primary air

GB

Does not require adjusting.

• Setting the burners to minimum

1. Turn the tap to the low ame position;

2. Remove the knob and adjust
the adjustment screw, which is
positioned in or next to the tap pin,

until the ame is small but steady.

3. Having adjusted the ame to the required low setting,

while the burner is alight, quickly change the position
of the knob from minimum to maximum and vice versa

several times, checking that the ame does not go out.

Checking the tightness of the connection

! When the installation process is complete, check the pipe

ttings for leaks using a soapy solution. Never use a ame.

Adapting to different types of gas

To adapt the hob to a different type of gas other than default
type (indicated on the rating plate at the base of the hob or
on the packaging), the burner nozzles should be replaced
as follows:

1. Remove the hob grids and slide the burners off their
seats.

2. Unscrew the nozzles using a 7 mm socket spanner, and
replace them with nozzles for the new type of gas (see

table 1 “Burner and nozzle characteristics”).

3. Reassemble the parts following the above procedure in
the reverse order.

4. Once this procedure is nished, replace the old rating

sticker with one indicating the new type of gas used.
Sticker are available from any of our Service Centres.

Replacing the Triple ring burner nozzles

1. Remove the pan supports and lift the burners out of their
housing. The burner consists of two separate parts (see
pictures).

2. Unscrew the nozzles using a 7 mm socket spanner.

Replace the nozzles with models that are congured

for use with the new type of gas (see Table 1). The two
nozzles have the same hole diameter.

3. Replace all the components by completing the above
operations in reverse order.

4. Some appliances have a safety device (thermocouple)

tted. If the device fails to work when the burners are set
to the low ame setting, increase this low ame setting

using the adjusting screw.

5. Once the adjustment has been made, replace the
seals on the by-passes using sealing wax or a similar
substance.

! If the appliance is connected to liquid gas, the regulation
screw must be fastened as tightly as possible.

! Once this procedure is nished, replace the old rating

sticker with one indicating the new type of gas used. Stickers
are available from any of our Service Centres.

! Should the gas pressure used be different (or vary slightly)
from the recommended pressure, a suitable pressure

regulator must be tted to the inlet pipe (in order to comply

with current national regulations).

DATA PLATE
Electrical

connections

see data plate

This appliance conforms to the following
European Economic Community directives:

- 2006/95/EEC dated 12/12/06 (Low
Voltage) and subsequent amendments

- 2004/108/EEC dated 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments

- 93/68/EEC dated 22/07/93 and
subsequent amendments.

- 2009/142/EEC dated 30/11/09 (Gas) and
subsequent amendments.

- 2012/19/EC and subsequent
amendments.

9