Hotpoint HTT18EBSERWW, HTT18EBSARWW, HTT18EBMERWW, HTT18EBMERCC, HTT16BBSGRWW Owner’s Manual

...

Top-Freezer

Refrigerators

Safety Information

Adapter Plugs ................. 3

Connecting Electricity .......... 3

Extension Cords ............... 2

Safety Precautions ............. 2

Operating Instructions

Automatic Icemaker ............ 8

Care and Cleaning .......... 9, 10

Shelves ..................... 5, 6

Storage Drawers .............. 6, 7

Temperature Controls ........... 4

Installation Instructions

Preparing to Install

the Rel_rigerator .............. 11

Reve_sing the Door Swing ... 15-21

Water Line Installation ...... 12-15

Troubleshooting Tips

Belbre You Call for Service . . .22-24

Normal Operating Sounds ...... 22

Write the model and serial numbers here:

Model # Serial #

You can find them on a label on the upper left side of tile fi'esh food compartment.

f_, Printedin theUnitedStates EXPORT 162D7737PO06 49-60251 02-03 JR _-_<_"._;,,PrintedonRecycledPoper

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

A WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual

SAFETYPRECAUflONS

When using electrical appliances, basic safety precautions should be followed, including the following:

NThis reDigerator must be properly installed

and located in accordance with tile Ins 'tallation

Instructions before it is used. Also see the How ToConnect Electricity section.

/;;;Do not attempt to stand on top of the refrigerator:

Doing so may result in bodily injury or damage to the refrigerator.

g_Do not allow children to climb, stand or hang

on the shelves in the refl'igeraton They could damage tile refl'igerator and seriously injure

themselves.

NDo not allow children to play with the refrigerator

or tamper with the controls.

g_Do not touch tile cold surfaces in tile fl'eezer

compartment when hands are damp or wet. Skin may stick to these extremely cold surfaces.

@Do not store or use gasoline or other flammable

vapors and liquids in the xdcinity of this or any other appliance.

g_Keep fingers out of the "pinch point" areas;

clearances between tile doors and between

tile doors and cabinet are necessarily small. Be careful closing doors when children are

in the area.

NIn refrigerators with automatic icemakers, avoid

contact with tile moving parts of tile ejector

mechanism, or with tile heating element that releases the cubes. Do not place fingers or hands

on the automatic icemaking mechanism while the refrigerator is plugged in.

g_Unplug the refl'igerator before cleaning and

making repairs.

NOTE:Westronglyrecommendthat anyservicingbe

performedby a quafifiedindividual

N Before replacinga burned-outlight bulb,the

refrigeratorshouldbe unpluggedin order to avoid

contact with a live wire filament. (A burned-out

light bulb may break when being replaced.)

NOTE:Turningthe controlto the0positiondoesnot remove

powerto thelightcircuit.

_Do not refl'eeze fl'ozen toods which have thawed

completely.

A DANGER!RISKOFCHILDENTRAPMENT

PROPERDISPOSALOFTHEREFRIGERATOR

Child entrapment and suffocation are not problems of the past..Junked or abandoned refrigerators are

still dangerous...even if they will sit tot '_ust a few days." If you are getting rid of your old refrigerator;

please follow the instructions below to help prevent

accidents.

Before You Throw Away YourOld Refrigerator or Freezer:

5;;;_Pake off the doors and discard separately.

%Leave the shelves in place so that children may

not easily climb inside.

% If the refl'igerator has a lock make it unusable.

USEOFEXTENSIONCORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

Howevm; if you must use an extension cord, it is absolutely necessary that it be a UL-listed, 3-wire grounding

type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 190 volts.

Refrigerants

_MIrefrigeration products contain refrigerants, which

under federal lawmust be removed prior to product

disposal. Kyou are getting rid of an old refrigeration

product, check with the company handling tile disposal

about what to do.

A WARNING!

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped Mth a 3-prong (grounding) plug which mates with a

standard g-prong (grounding) wall outlet m

minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where an ungrounded ,a-all outlet is encountered,

it is your personal responsibility and obligation to have it replaced with a properly grounded

3-prong wall outlet.

The refrigerator should al,a-ays be plugged into

its own individual

electrical outlet. This

provides the best performance and also

prevents overloading house wiring circuits

which could cause a fire hazard from overheated wires. Please refer to the rating plate on the

refrigerator fbr the correct voltage, wattage and

frequency. If the product plug does not fit your outlet, the product should be fitted with a new plug.

IMPORTANT:Therefitting of electricplugsandcablesshould bedonebya quafifiedtechnicianor serviceagent.Insome

countriestherefittingofelectricplugsandcablesis only

permittedwhentheworkis completedbya qualified

technician.

If the power supply cord becomes damaged, it must

be replaced by a qualified service agent in order to avoid a safety hazard.

Never unplug your refrigerator by pulling on the power cord. Al,a-ays grip plug firmly and pull straight

out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end. When moving the refrigerator a,a-ayfrom the wall,

be careful not to roll over or damage the power cord.

Mains Lead Replacement

If the mains lead on your refrigerator needs replacing at any time, it must be replaced by a

special lead which is obtainable from your local dealen A charge will be made for the replacement of the mains lead if you have damaged the lead.

USEOFADAPTERPLUGS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

Howevm; if you must use an adapter, where local codes permit, a temporary¢omlection may be made to a properly grounded 2-prong wall oudet by use

of a UL-listed adapter available at most local hardv,-are stores.

The larger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord. When disconnecting the power cord from the

adaptm; always hold the adapter in place with one hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOTUSE the refrigerator until a proper ground has been

established.

Attachingthe adaptorgroundterminaltoa waftoutletcover

screwdoesnotgroundtheapplianceunlessthe coverscrew ismetal,andnot insulated,andthewaftoutletis grounded throughthehousewiring.Youshouldhavethe circuit checked bya quafifiedelectriciantomakesurethe outlet isproperly

grounded.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Aboutthetemperaturecontroldial

Turning the dial to 0stops cooling in both compartments--fresh food and freezer. It does not shut off power to the

refrigerator.

ControlSettings

Temperature ControlDial

The temperature control dial has nine settings plus

0. 1 is the warmest. 9 is the coldest. At first, set tile dial at 5.

After using tile refl'igeratol, adjust the dial if necessa_ T.

Anti-Condensation Switch (on somemodels)

If moisture develops on the ceiling of the

fl'esh food compartment, turn the anti- condensation switch to the 1(on) position.

Moisture is likely to appear when tile air is humid--in tile summm; in the early

.......................................................................................morning hours or in non-air conditioned

rooms. Move to the 0 (OFF) position in less humid conditions.

Insert a coin into the slot in the middle of the dial and you can turn the dial to the setting that's best

suited to your needs. Allow 94 hours for the refrigerator to get cold.

Aboutthefreshfoodcompartmentshelves.

Shelf supports at various levels allow you to custom-space your shelves. Not all features are on all models.

Half-Width Shelves

One end of the shelf rests on a molded side-

wall support; a bracket on the other end

hooks into a track on the rear cabinet wall.

TOremove, lift the shelf up at fi'ont, then off

the support and out of the track.

TOreplace, select desired shelf height. With

shelf fi'ont raised slightly, hook the bracket's top lug into the track, then lower the shelf onto the support.

Full-Width Shelves

Some models have a steel wire sliding shelf, a stationary tempered glass shelf or two steel

wire stationary shelves. These shelves can be moved to another place in the fi'esh food compartment.

The fhll:width sliding shelf has stop-locks. When placed correctly on tbe shelf supports,

the shelf will stop before coming completely out of the refiigerator and will not tilt when

you place food on it or remove food from it.

TOremove the full-width shelves, lift the rear

of the shelf and pull forward.

NOTE:Theshelftothe right of thetrackis designed to hookinto therighbhandslot, theshelf to theleft isdesignedtohookinto the left-handslot.

Toremovea full-width shelf when thefresh foodcompartmentdoorcannotbe openedfully,

lift tile rear of tile shelf, pull forward and down, tilt tim shelf and take it out.

Aboutthe frozenfoodcompartmentshelves.

Some models have an ice-tray shelf and some have a full-width step shelf.

Ice- TrayShelf

To remove the ice-trayshelf, lift the left side of the shelf off its supports, then pull the shelf

to the left to free it of the plug supports.

Step Sheff

To remove the step shelf:

[_Lifl left side of shelf slighdy. [_ Move shelf to tlle left to fi'ee its right ends

from holes in the cabinet wall.

[]Lower right side of shelf; move shelf to the

right and take it out.

To replace the step shelf:

[_ With shelf tilted as shown, fit left ends of

shelf into holes in cabinet wall.

fit right ends of shelf into holes in cabinet wall, and lower shelf into place.

[_ Lift left side of shelf slightly, swing shelf up,

Pull the shelf to the right to free the pins from the holes in the cabinet wall.

Ice Traits Ion some models)

Ice trays are designed to release ice cubes easily. Hold tray upside<lown over a

container and twist both ends to release cubes.

About the storage drawers.

Not all features are on all models.

Fruit and Vegetable Drawers

Excess water that may accumulate in the bottom of the drawers should be emptied

and the drawers wiped dry.

Snacks Drawer

This drawer can be moved to the most

useful location for your family's needs.

For only one or two ice cabes, leave the tray right-side up, tudst both ends slightly and

remove desired number of cubes. Wash ice

trays and storage bin in lukewarm water only.

Do not put them in an automatic dish,a-ashen

About storage drawer and cover removal

Not all features are on all models.

Drawer and Cover Removal

Drawers can be removed easily by grasping tile sides and lifting up slightly while pulling

drawers past the step location.

Full-Width Drawer with Plastic Cover

TOremovethecover,lif} it off its supports,

pull it forward, tilt it and take it out.

Twin Drawers with Glass Cover

To remove:

[Remove the drawers. []Reach in, push the front of glass cover

up, and at the same time, pull it forward as fhr as it will come.

Tilt it and take it out. Avoid cleaning the cold glass cover with hot water because the

extreme temperature difference may cause it to break.

[]Remove the drawer frame. (Al,a-ays

remove the glass cover before you take out the drawer frame.)

Lif} the frame off the supports at each side and back, pull it forward, tilt it and take

it out.

Toreplace:

[]Lower the frame until it rests on the

supports at each side and back.

[]Replace the glass covm; pushing its rear

edge firmly into the rear frame channel and gently lowering the fi'ont into place.

[]Replace the drawers.

About the automatic icemaker. (onsome models)

A newly-installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Icemaker (onsomemodels)

The icemaker will produce seven cubes per cycle,---approximately 100-130 cubes in a

24-hour period, depending on freezer compamnent temperature, room temperarure,

number of door openings and other use conditions.

There are two types of icemakers: power switch

Powerswitchmodel

d_ to 15°F (-9°C). A newly-installed refrigerator

Feelerarmmodel cubes.

models and feeler arm models.

If the refrigerator is operated betore the water connection is made to the icemakm; set the

powertheSTOP(up)position.SWitchre 0 (off)or move the teeler arm to

the water supply, set the power switch to the I

(on)position or move the teeler arm to the ON (do,m) position. On power switch models, the

Whentherefrigeratorhasbeenconnectedto

green light _MIIcome on. The icemaker will till with water when it cools

may take 12 to 24 hom_ to begin making ice

You will hear a buzzing sound each time the icemaker fills with water

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the teeler arm,

the icemaker will stop producing ice. It isnormal for several cubes to be joined

togethen If ice is not used fi'equently, old ice cubes will

become cloudy, raste stale and shrink. On power switch models, the green power light

will blink if ice cubes get stuck in the icemaken

To correct this, set the power switch to 0 (off) and remove the cubes. Set the power swirch to I (on)to resrart the icemaken After the icemaker

has been turned on again, there will be a delay of about 45 minutes before the icemaker

resumes operation.

NOTE:Inhomeswithlower-than-averagewater pressure,youmayheartheicemakercyclemultipletimes

whenmakingonebatchof ice.

Throw away the first few batches of ice to allow the water line to clean

Icemaker Accessory Kit

If your refrigerator did not already come equipped with an automatic icemakm;

an icemaker accessory kit is available at extra cost.

Check the back of the refrigerator 1or the specific icemaker kit needed for your model.

Care and cleaning of the refrigerator.

Cleaning the Outside

The door handles and trim (on some models).

Clean with a cloth dampened with soapy ,a_aten Dry with a soft cloth.

Keep the outside clean. Wipe with a clean cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.

Cleaning the Inside

TOhelp prevent odors, leave an open box of

baking soda in the fresh food and freezer compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture out of sponge or cloth when cleaning

around switches, lights or controls. Use warm water and baking soda solution--

about a 'tablespoon (15 ml) of baking soda to a quart (1 liter) of watm: This both cleans and

neutralizes odors. Rinse and wipe dry.

Donot wipe therefrigeratorwith asoileddishcloth or wet towel Thesemayleavea residuethatcan erodethepaint. Donotusescouringpads,powdered cleaners,bleachor cleanerscontainingbleach

becausetheseproductscanscratchandweakenthe paint finish.

Avoidcleaningcoldglassshelves(onsomemodels)

with hot waterbecausethe extremetemperature differencemaycausethemtobreaL Handleglass shelvescarefully.Bumpingtemperedglasscancause

it to shatte_

Donot washanyplasticrefrigeratorparts inthe dishwasher

Cleaning the condenser coils,

Squeezeto release the hook.

After cleaning the door gaskets, apply a thin layer of petroleum .jelly to the door gaskets at

the hinge side. This helps keep the gaskets from sticking and bending out of shape.

Condenser

There is no need for routine condenser cleaning in normal home operating

environments. Howevm, in environments that may be particularly dusty or greasy, the condenser should be cleaned periodically

for efficient refrigerator operation.

Light Bulb Replacement (onsomemodels)

A light bulb and socket are located at the top of the flesh food compartment

opposite the temperature control panel.

To clean the condensm; turn the temperature control dial to 0. Sweep away or vacuum up dust.

For best results, use a brush specially designed for this purpose. It is available at most appliance parts stores.

To replace the bulb, first unplug the refrigerator from its electrical outlet.

Put your hand under the light shield and release the hook at the bulb end of the

shield. (The light shield is on some models.)

Care and cleaning of the refrigerator.

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. MI types of floor

coverings can be damaged, particularly cushioned coverings and those with

embossed surfaces.

Turn the leveling legs at each front corner of the refrigerator counterclockwise until

the rollers support the refrigerator. Pull tile refrigerator straight out and return it to

position by pushing it straight in. Moxdng the refrigerator in a side direction may result in

damage to tile floor covering or refrigerator.

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigeratoi: Move the

temperature control dial to the 0 position, and clean the interior with a baking soda

solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) ofwaten

Leave the doors open.

Whenpushingthe refrigeratorback,makesureyou don'trail overthepowercordor icemakersupplyline fensomemodels).

After rolling tile refrigerator back into place, turn the legs clockwise until the legs again

bear the weight of tile refrigeratol:

Set the icemaker power switch to the

0 (off)position or move the fizeler arm to the

STOP (up) position (depending on model) and shut off the water supply to the

refrigeraton If the temperature can drop below freezing,

have a qualified servicer drain the v_-ater supply system (on some models) to prevent

serious property damage due to flooding.

Preparing to Move

Secure all loose items such as grille, shelves and drawers by taping them securely in

place to prevent damage.

Besuretherafrigeratorstaysinan up@t position duringmoving.

Installation

Refrigerato

Instructions

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Obso ,,call

governing codes and ordinances.

• Note to Installer - Besure to leave these

instructions with the Consumes:

• Note to Consumer - Keep these instructions

for future reference.

• Skill level - Installation of this appliance requires basic mechanical skills.

• Completion time - Refrigerator Installation

15 minutes

Reversing the Door Swing

1 hour

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not covered under the Warranty.

Models 15,16,17 and 18

DIMENSIONS

Model 15 16 17 18

A* 61" (155cm) 64" (163cm) 67" (170cm) 67" (170cm)

B 28" (71cm) 28" (71cm) 28" (71cm) 28" (71 cm) C** 317J(79cm) 317J(79cm) 327(' (81cm) 321//' (82cm) D M7/_#(139cm) M7/J (139cm) 56"(142cm) 563/s" (143cm) E 26" (66cm) 26" (66cm) 267/' (68 cm) 267/,/(68 cm)

* Height does not include hinge--Add 22 mm for hinge.

** Depth includes handle.

WATER SUPPLY TO THE ICEMAKER

(on some models)

If the refrigerator has an icemakm; it Mll have to be connected to a cold drinking water line. A water supply kit (containing copper tubing, shutoffvalve, fittings and instructions) is available at extra cost from your dealm: Installation of the icemaker must be done by

a qualified service technician.

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough tu maintain proper temperatures.

• Install it on a floor strong enough to support it Ihlly loaded.

CLEARANCES

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

• Sides 3/4" (19 mm)

• Top 1" (25 mm)

• Back 1" (25 mm)

ROLLERS AND LEVELING LEGS

Leveling legs near each front corner of the refrigerator are adjustable. They firmly position the refrigerator

and prevent it from moving when the doors are opened. Leveling legs should be set so the front of the

refrigerator is raised just enough that the doors close easily when opened about halfway.

Turn the leveling legs clockwise to raise the refrigerator; counterclockwise to lower it.

Rollers next to the leveling legs allow you to move the refrigerator away from the wall for cleaning.

Turn the legs counterclocDMse until the weight of the refrigerator is transfizrred from them tu the rollers.

After rolling the refrigerator back into place, turn the legs clocDMse until the legs again bear the weight of

the refrigeraton

Installation Instructions

Kll INSTALLING THE WATER LINE

BEFORE YOU BEGIN

This w-ater line installation is not w-arranted by the refrigerator or icemaker manufacturer. Follow these

instructions carefully to minimize the risk of expensive

water damage.

Water hammer (water banging in the pipes) in house

plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified

plumber to correct,a-ater hammer before installing the water supply line to the refrigeratoE

To prevent burns and product damage, do not hook up the water line to the hot water line.

If you use your refrigerator before connecting the

water line, make sure tile icemaker power switch is

in the OFF position (on power switch models) or the feeler arm is in the STOP (up) position

(on feeler arm models).

Do not install the icemaker tubing in areas where temperatures fall below fi'eezing.

When using any electrical device (such as a power

drill) during installation, be sure tile device is insulated or wired in a manner to prevent the hazard

of electric shock.

All installations must be in accordance with local

plumbing code requirements.

Installation of the icemaker must be done by a qualified service technician.

WHAT YOU WILL NEED (CONT.)

• Power drill.

• Copper tubing, 1/4" outer diameter to connect the

refrigerator to the w-ater supply. Be sure both ends of the tubing are cut square.

Do not use plastic tubing or plastic fittings because the water supply line is under pressure at all times. Certain types of plastic tubing may become brittle with age and crack, resulting in w-ater leakage.

• Two l/4 " outer diameter compression nuts and 2 ferrules (sleeves)--to connect the copper tubing to the shutoffvalve and the refrigerator

water valve.

WARNING! Connect to potable

water supply only.

WHAT YOU WILL NEED

To determine how much copper tubing you need:

Measure the distance from the water valve on the back

of the refrigerator to the water supply pipe. Then add

8 feet (244 cm). Be sure there is sufficient extra tubing

[about 8 leer (244 cm) coiled into 3 turns of about

10" (25 cm) diameter] to allow the refrigerator to move out from the wall after installation.

• A water supply kit (containing copper tubing, shutoff

valve and fittings listed below) is available at extra cost

from your local distributor:

• A cold drinking water supply. The water pressure must

be between 20 and 120 p.s.i. (1.4-8.1 bar).

• If your existing water line has a flared fitting at the

end, you will need an adapter (available at plumbing supply stores) to connect the water line to the

refrigerator OR you can cut off the flared fitting

with a tube cutter and then use a compression fitting.

• Shutoff valve to connect to the cold water line.

The shutoffvalve should have a ,a_ater inlet Mth a

minimum inside diameter of 5/32" at the point of

connection to the COLD WATER LINE. Saddle-vype shutoff valves are included in many water supply kits.

Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

Installation Instructions

Install the shutoff valve on the nearest frequently used drinking water line.

[] SHUT OFF THE MAIN WATER

SUPPLY

Turn on the nearest faucet long enough to clear the line of water.

[] FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe with the pipe clamp.

PipeClamp

[] CHOOSE THE VALVE LOCATION

Choose a location for the valve that is easily accessible. It is best to connect into the side of a

vertical ,a-ater pipe. When it is necessary m connect

into a horizontal ,a-ater pipe, make the connection to the top or side, rather than at the bottom,

to avoid drawing offany sediment from tile

,a-ater pipe.

[] DRILL THE HOLE FOR THE VALVE

Drill a 1/4" hole in the water pipe, using a sharp

bit. Remove any burrs resulting fi'om drilling the

hole in the pipe.

Saddle-Type_ ShutoffValve

VerticalColdWaterPipe

[] TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer begins to swell.

NOTE: Do not overtighten or you may crush the copper tubing.

Washer

Inlet End

[] ROUTE THE TUBING

Route the copper tubing between the cold water line and the refi'igerator.

Route the tubing through a hole drilled in the _a-all or floor (behind the refi'igerator or adjacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing

[about 8 feet (944 cm) coiled into 3 turns of about

lO" (25 cm) diameter] to allow the refi'igerator to move out from the wall after installation.

Installation Instructions

B INSTALLING THE WATER LINE (CONT.)

[] CONNECT THE TUBING TO THE

VALVE

Place the compression nut and ferrule (sleeve) onto the end of the tubing and connect it to the

shutoff valve. Make sure the tubing is fully inserted into the valve.

Tighten tile compression nut securely.

Saddle-TypeShutoffValve

3mpressi0nNut

PackingNut

OutletValve

[] FLUSH OUT THE TUBING

Turn the main water supply on and flush out the tubing until the water is clear.

Shut the water offat the water valve after about one quart (1 liter) of water has been flushed

tbrough the tubing.

[] CONNECT THE TUBING TO THE

REFRIGERATOR (CONT.)

9.1 Remove the access cover.

9.2 Remove the plastic flexible cap fi'om the

water valve.

9.3

Place tile compression nut and ferrule (sleeve) onto the end of the tubing as shown.

Insert the end of tbe copper tubing into the

water valve connection as far as possible. While holding the tubing, tighten the fitting.

[] CONNECT THE TUBING TO THE

REFRIGERATOR

NOTES:

• Before making the connection m the refrigerator,

be sure the refrigerator power cord is not plugged into the ,a-all outlet.

• We recommend installing a water filter if your water supply has sand or particles that could clog

tile screen of tile refi'igerator's water valve. Install it in tile water line near the refrigerator:

Fasten the copper tubing into the clamp

provided to hold it in a vertical position.

You may need to pry open the clamp.

1/4" CopperTubing

1/4" Compression

fFerrule(sleeve)

9.4 Reattach the access covm:

Installation Instructions

[] TURN THE WATER ON AT THE

SHUTOFF VALVE

Tighten any connections that leak.

[] PLUG IN THE REFRIGERATOR

Arrange tile coil of copper tubing so that it does not vibrate against the back of the refrigerator or against

the w_all.Push the refrigerator back to the w_all.

[] START THE ICEMAKER

On power switch models, set the icemaker power switch to the ! (on) position. On feeler arm models,

move the feeler arm to the ON (down) position. The icemaker will not begin to operate until it reaches

its operating temperature of 15°F (-9°C) or below. It will then begin operation automatically.

Powerswitchmodel

STOP (up} position

rArmin

theON{down)position

Feelerarmmodel

NOTE: In lower water pressure conditions, the

water valve may turn on up to 3 times to deliver

enough water to the icemaker.

IFJIREVERSING THE DOOR SWING

IMPORTANT NOTES

When reversing the door swing:

• Read the instructions all the way through before

starting.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid using them in the wrong places.

• Provide a non-scratching work surface for the doors.

IMPORTANT: Once you begin, do not move the cabinet until door-swing reversal is completed.

These instructions are fbr changing the hinges fl'om the right side to the left side--if you ever want to

change tile hinges back to the right side, follow these same instructions and reverse all references to left

and right.

TOOLS REQUIRED

Phillips screwdriver

5/16" hex-head socket driver

Putty knifie or thin- blade screwdriver

Masking tape

T20 or T25 Torxdriveg

(needed fbr

some models)

5/16" openmnd

wrench

+ 33 hidden pages