Horizon Fitness Paros 2.0 operation manual

COMFORT 2.0 COMFORT 4.0 COMFORT 8.1 COMFORT R8.0

MANUEL DU PROPRIÉTAIRE

Read the BIKE GUIDE before using this OWNER’S MANUAL. Lesen Sie das ERGOMETER-HANDBUCH, bevor Sie dieses BENUTZERHANDBUCH verwenden. Lees de FIETSGIDS voor u deze GEBRUIKERSHANDLEIDING gebruikt. Lisez le GUIDE DU VÉLO avant d’utiliser ce MANUEL DU PROPRIÉTAIRE.

OWNER’S MANUAL

BENUTZERHANDBUCH

GEBRUIKERSHANDLEIDING

3 ENGLISH 61 DEUTSCH 119 NEDERLANDS 177 FRANÇAIS

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

When using an exercise product, basic precautions should always be followed, including the following: Read all instructions before using this exercise bike. It is the responsibility of the owner to ensure that all users of this exercise bike are adequately informed of all warnings and precautions. If you have any questions after reading this owner’s manual, contact your local dealer.

WARNING

READ AND SAVE ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EXERCISE BIKE. IT IS STRONGLY RECOMMENDED TO TAKE THE FOLLOWING SAFETY INSTRUCTIONS.

• CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult your physician before continuing.

• Use this exercise bike for its intended purpose as described in this manual. Do not use attachments that have not been recommended by the manufacturer.

• Never operate the exercise bike if it is not working properly, or if it has been damaged. Contact the authorized dealers for examination and repair.

• Do not use the exercise bike without proper footwear. NEVER operate the exercise bike with bare feet.

• Do not wear any clothing that might catch on any moving parts of this exercise bike.

• Keep hands and feet clear at all times from moving parts to avoid injury. Never turn the pedal cranks by hand.

• Do not dismount the exercise bike until the pedals are at a complete STOP.

• Do not attempt to ride the exercise bike in a standing position at high RPMs until you have practiced at slower speeds.

• Do not insert any object, hands or feet into any openings, or expose hands, arms or feet to the drive mechanism or other potentially moving part of the exercise bike.

• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

• Close supervision is necessary when used near children, invalids or disabled people.

• When the exercise bike is in use, young children and pets should be kept at least 3 meters / 10 feet away.

• Ensure that adjustment levers (seat and handlebar fore-and-aft) are properly secured and do not interfere with range of motion during exercise.

• This application is for home and indoor use only.

• This application with speed independent system.

• If any of the adjustment devices are left projecting, they could interfere with the user’s movement.

• WARNING! Heart rate monitoring systems may be inaccurate. Over exercising may result in serious injury or death. If you feel faint stop exercising immediately.

ASSEMBLY

WARNING

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the exercise bike could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the exercise bike, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your exercise bike’s serial number located on the front stabilizer tube and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOX BELOW:

SERIAL NUMBER:

MODEL NAME: HORIZON

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

SERIAL NUMBER LOCATION

Comfort

R8.0

HANDLEBARS

SEAT BACK

CONSOLE

CONSOLE MAST

PULSE GRIP HANDLEBARS

WATER BOTTLE HOLDER

SEAT BASE

CRANK

REAR STABILIZER

FRONT STABILIZER TUBE

PEDALS

CONSOLE MAST GROMMET

POWER CORD SOCKET

SEAT POSITION

ADJUSTMENT LEVER

MAIN FRAME

TRANSPORT WHEELS

TOOLS REQUIRED:

F 13/15mm Flat Wrench/Screwdriver F 5mm L-Wrench F 6mm L-Wrench

RECUMBENT BIKE PRE ASSEMBLY

UNPACKING

PARTS INCLUDED:

F 1 Main Frame F 1 Console F 1 Console Mast F 1 Console Mast Grommet F 1 Water Bottle Holder F 1 Front Stabilizer Tube F 1 Rear Stabilizer Tube F 1 Seat Base F 1 Seat Back F 1 Seat Frame F 1 Seat Frame Cover F 1 Pulse Grip Handlebars F 2 Pedals with Straps F 1 Audio Adapter Cable F 1 Power Cord F 1 Hardware Kit

Unpack the product where you will be using it. Place the bike carton on a level flat surface. It is recommended that you place a protective covering on your floor. Never open box when it is on its side.

IMPORTANT NOTES

During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded. It is recommended you complete the full assembly of your unit before completely tightening any ONE bolt.

Several parts have been pre-lubricated to aid in assembly and usage. Please do not wipe this off. If you have difficulty, a light application of lithium bike grease is recommended.

NEED HELP?

If you have questions or if there are any missing parts, contact your local dealer. Contact information may be located on the back panel of your manual or on the warranty card.

Comfort

R8.0

Comfort

R8.0

RECUMBENT BIKE ASSEMBLY STEP 1

NUT (D)

SPRING WASHER (C)

FLAT WASHER (B)

MAIN FRAME

A Open HARDWARE FOR STEP 1.

B Attach the REAR STABILIZER to the MAIN

FRAME using 2 BOLTS (A), 2 FLAT WASHERS (B), 2 SPRING WASHERS (C) and 2 NUTS (D).

C Attach the FRONT STABILIZER to the MAIN

FRAME using 2 BOLTS (A), 2 FLAT WASHERS (B), 2 SPRING WASHERS (C) and 2 NUTS (D).

REAR STABILIZE R

HARDWARE FOR STEP 1

BOLT (A) M8 X 56 MM QTY: 4

SPRING WASHER (C) M8 X 2.0T MM QTY: 4

FLAT WASHER (B) Φ9X Φ18 X 2.0T MM QTY: 4

NUT (D) M8 QTY: 4

BOLT (A)

FRONT STABILIZER

Note: Lifting up the machine will help your assembly. First put in place the stabilizer and then insert the bolts will also make your assembly easier.

RECUMBENT BIKE ASSEMBLY STEP 2

A Open HARDWARE FOR STEP 2.

B Slide WATER BOTTLE HOLDER up CONSOLE

MAST and align screw holes in WATER BOTTLE HOLDER with holes in CONSOLE MAST.

C Attach the WATER BOTTLE HOLDER using 2

CONSOLE MAST

WATER BOTTLE HOLDER

SCREW (E)

SCREWS (E).

HARDWARE FOR STEP 2

SCREW (E) M4 X 12 MM QTY: 2

Comfort

R8.0

Comfort

R8.0

RECUMBENT BIKE ASSEMBLY STEP 3

CONSOLE MAST

CONSOLE MAST GROM MET

CONSOLE CABLES

FLAT WASHER (B)

BOLT (F)

BOLT (G)

MAIN FRAME

A Open HARDWARE FOR STEP 3.

B Slide CONSOLE MAST GROMMET from the

bottom up the CONSOLE MAST .

C Attach CONSOLE CABLES and carefully tuck all

cables into MAIN FRAME. Slide CONSOLE MAST into MAIN FRAME.

D Attach the CONSOLE MAST using 2 BOLTS

(G) from the sides and 4 BOLTS (F) and 4 FLAT WASHERS (B) from the front.

E Slide CONSOLE MAST GROMMET down over

MAIN FRAME.

HARDWARE FOR STEP 3

BOLT (F) M8 X 60 MM QTY: 4

FLAT WASHER (B) Φ9 X Φ18 X 2.0T MM QTY: 4

BOLT (G) M8 X 18 MM QTY: 2

RECUMBENT BIKE ASSEMBLY STEP 4

HARDWARE FOR STEP 4

BOLT (I) M8 X 18 MM QTY: 6

SPRING WASHERS (C) M8 X 2.0T MM QTY: 6

Comfort

R8.0

BOLT (I)

SPRING WASH ER (C)

MAIN FRAME

SEAT FRAME

A Open HARDWARE FOR STEP 4.

B Attach SEAT FRAME to the MAIN FRAME using 6

SOCKET HEAD CAP SCREWS (I) and 6 SPRING WASHERS (C) as shown.

Comfort

R8.0

RECUMBENT BIKE ASSEMBLY STEP 5

A Open HARDWARE FOR STEP 5.

SEAT BACK

SEAT BASE

BOLT (J)

FLAT WASHER (B)

SEAT FRAME

B Attach SEAT BASE to SEAT FRAME using 4

BOLTS (J) and 4 FLAT WASHERS (B).

C Attach SEAT BACK to SEAT FRAME using 4

BOLTS (J) and 4 FLAT WASHERS (B).

HARDWARE FOR STEP 5

BOLT (J) M8 X 45 MM QTY: 8

FLAT WASHER (B) Φ9 XΦΦ18 X 2.0T MM QTY: 8

RECUMBENT BIKE ASSEMBLY STEP 6

A Open HARDWARE FOR STEP 6.

B Attach PULSE GRIP HANDLEBARS to the

SEAT FRAME using 2 BOLTS (K) and 2 ARC WASHERS (H).

C Attach SEAT FRAME COVER to MAIN FRAME as

shown.

Attach the heart rate wires from the PULSE GRIP HANDLEBARS to the heart rate wires on the MAIN FRAME.

Note: Before assembly the handle make sure the handle is in right position with heart rate grip facing up and cable down.

SEAT FRAME COVER

SEAT FRAME

MAIN FRAME

PULSE G RIP HAN DLEBARS

BOLT (K)

ARC WASHER S (H)

HARDWARE FOR STEP 6

Comfort

R8.0

Comfort

R8.0

RECUMBENT BIKE ASSEMBLY STEP 7

CONSOLE

A HARDWARE FOR STEP 7 is pre-installed.

CONSOLE CABLE

RIGHT CRAN K ARM

RIGHT PE DAL

CONSOLE MAST

PRE-ASSEMBLED

SCREW

LEFT PEDAL

B Attach the RIGHT PEDAL to the RIGHT CRANK

ARM, tightening it clockwise with the provided

13mm/15mm flat wrench.

C Attach the LEFT PEDAL onto the left crank arm,

tightening it counter-clockwise with the provided 13mm/15mm flat wrench. (NOTE: The left crank arm is reversed threaded so it is very important that it is tightened counter-clockwise. Tightening it the opposite way can damage the pedal or the crank arm or both.)

D Connect the CONSOLE CABLE and carefully tuck

into the CONSOLE MAST.

E Attach the CONSOLE to the CONSOLE MAST

using 4 PRE-ASSEMBLED SCREWS.

HARDWARE FOR STEP 7

PRE-ASSEMBLED SCREW M5 X 7 MM QTY: 4

Note: You may need a 15mm wrench to assemble the pedal. Please be care not to pinch yourself when assembling.

RECUMBENT BIKE ASSEMBLY

ASSEMBLY COMPLETE!

Comfort

R8.0

Comfort R8.0

Overall Dimension: 165 x 64 x 135 cm Net Weight: 49.5 kg / 109 lbs. Gross Weight: 56.5 kg / 124 lbs. Max. User Weight: 136 kg / 300 lbs.

CONSOLE

SMART DEVICE

AND READING RACK

Comfort Upright

Bike

HEART RATE GRIP

SEAT

TOWEL HOOK

SEAT POSITION ADJUSTMENT KNOB

SEAT POST TUBE

PEDALS

CRANK

POWER CORD SOCKET

REAR STABILIZER

FRONT STABILIZER TUBE

HANDLEBARS

CONSOLE MAST

WATER BOTTLE HOLDER

SEAT HEIGHT ADJUSTMENT KNOB

CONSOLE MAST GROMMET

MAIN FRAME

TRANSPORT WHEELS

( COMFORT 2.0 SHOWN )

TOOLS REQUIRED:

F 13/15mm Flat Wrench/Screwdriver F 6mm L-Wrench

UPRIGHT BIKE PRE ASSEMBLY

UNPACKING

PARTS INCLUDED:

F 1 Main Frame F 1 Console F 1 Console Mast F 1 Console Mast Grommet F 1 Water Bottle Holder F 1 Front Stabilizer F 1 Rear Stabilizer F 1 Seat F 1 Seat Post Tube F 2 Pedals with Straps F 1 Audio Adapter Cable F 1 Power Cord F 1 Hardware Kit

IMPORTANT NOTES

During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded. It is recommended you complete the full assembly of your unit before completely tightening any ONE bolt.

Several parts have been pre-lubricated to aid in assembly and usage. Please do not wipe this off. If you have difficulty, a light application of lithium bike grease is recommended.

NEED HELP?

If you have questions or if there are any missing parts, contact your local dealer. Contact information may be located on the back panel of your manual or on the warranty card.

Comfort Upright

Bike

Comfort Upright

Bike

UPRIGHT BIKE ASSEMBLY STEP 1

NUT (C)

SPRING WASHE R (I)

FLAT WASHER (B)

MAIN FRAME

REAR STABILIZE R

FRONT STABILIZER

BOLTS (A)

HARDWARE FOR STEP 1 :

HARDWARE FOR STEP 1

BOLT (A) M8 X 56 MM QTY: 4

NUT (C) M8 QTY: 4

FLAT WASHER (B) Φ9 XΦΦ20 X 2.0T MM QTY: 4

SPRING WASHER (I) M8 X 2.0T MM QTY: 4

A Open HARDWARE FOR STEP 1.

B Attach the REAR STABILIZER to the MAIN

FRAME using 2 BOLTS (A), 2 FLAT WASHERS (B), 2 SPRING WASHER (I) and 2 NUTS (C).

C Attach the FRONT STABILIZER to the MAIN

FRAME using 2 BOLTS (A), 2 FLAT WASHERS (B), 2 SPRING WASHER (I) and 2 NUTS (C).

Note: Lifting up the machine will help your assembly. First put in place the stabilizer and then insert the bolts will also make your assembly easier.

COMFORT 2.0 SHOWN

UPRIGHT BIKE ASSEMBLY STEP 2

S EAT

SEAT POST TUBE

SEAT HEIGHT ADJUSTMENT KNOB

MAIN FRAME

Note: There is no hardware needed at this step.

A Attach the SEAT to the SEAT POST TUBE and

tighten the SEAT NUTS by using 13mm wrench. (You may need additional 13mm wrench to make the seat assembly more easier.)

B Loosen the SEAT HEIGHT ADJUSTMENT KNOB

by turning it two half turns counter-clockwise.

C Then pull the SEAT HEIGHT ADJUSTMENT

KNOB outward while sliding the SEAT POST TUBE into the MAIN FRAME.

Note: While assembling the SEAT please make sure the seat is in right position. Tilt up the front of the SEAT might help you gain a more stable riding experience.

Comfort Upright

Bike

COMFORT 2.0 SHOWN

Comfort Upright

Bike

UPRIGHT BIKE ASSEMBLY STEP 3

CONSOLE MAST

HARDWARE FOR STEP 1 :

HARDWARE FOR STEP 3

SCREW (D) M4 X 12 MM QTY: 2

A Open HARDWARE FOR STEP 3.

B Slide WATER BOTTLE HOLDER up CONSOLE

MAST and align screw holes in WATER BOTTLE HOLDER with holes in CONSOLE MAST.

C Attach the WATER BOTTLE HOLDER using 2

SCREWS (D).

SCREW (D)

COMFORT 2.0 SHOWN

WATER BOTTLE HOLDER

Note: Be careful not to pinch any cable while assembling.

UPRIGHT BIKE ASSEMBLY STEP 4

CONSOLE MAST

GROMM ET

POSITIONI NG NOTCH

NUT (H)

MAIN FRAME

CONSOLE CABLES

BOLT (G)

BOLT (E)

FLAT WASHER (B)

HARDWARE FOR STEP 4

BOLT (E) M8 X 60 MM QTY: 4

BOLT (G) M8 X 15 MM QTY: 2

FLAT WASHER (B) Φ9 XΦΦ20 X 2.0T MM QTY: 4

NUT (H) M8 QTY: 4

A Open HARDWARE FOR STEP 4.

B Slide CONSOLE MAST GROMMET from the

bottom up the CONSOLE MAST with the small POSITIONING NOTCH facing forward.

C Attach CONSOLE CABLES and carefully tuck all

cables into MAIN FRAME. Slide CONSOLE MAST into MAIN FRAME.

D Attach the CONSOLE MAST using 2 BOLTS

(G) from the sides and 4 BOLTS (E), 4 FLAT WASHERS (B), 4 NUTS (H).

E Slide CONSOLE MAST GROMMET down over

MAIN FRAME.

Comfort Upright

Bike

COMFORT 2.0 SHOWN

Comfort Upright

Bike

UPRIGHT BIKE ASSEMBLY STEP 5

CONSOLE MAST

T KNOB (F)

HARDWARE FOR STEP 5

T KNOB (F) M8 X 64 X 32 QTY: 1

A Open HARDWARE FOR STEP 5.

B Holding HANDLEBAR close to CONSOLE MAST

and feed the HANDLBAR WIRES through the hole in the CONSOLE MAST and out the top of the CONSOLE MAST.

C Attach handlebar to CONSOLE MAST using 1

T KNOB (F).

Note: You may need extra help to route the heart rate cable and tighten the handlebar.

COMFORT 2.0 SHOWN

UPRIGHT BIKE ASSEMBLY STEP 6

CONSOLE

PRE-INSTALLED SCREW

CONSOLE MAST

CRANK ARM

Note: There is no hardware needed at this step.

A HARDWARE is pre-installed.

B Attach the RIGHT PEDAL to the RIGHT CRANK

ARM, tightening it clockwise with the provided 13mm/15mm flat wrench.

C Attach the LEFT PEDAL onto the left crank arm,

D Connect the CONSOLE CABLE and carefully tuck

into the CONSOLE MAST.

E Attach the CONSOLE to the CONSOLE MAST

using 4 PRE-INSTALLED SCREWS.

Note: You may need a 15mm wrench to assemble the pedal. Please be care not to pinch yourself when assembling.

Comfort Upright

Bike

COMFORT 2.0 SHOWN

RIGHT PEDAL

Comfort Upright

Bike

UPRIGHT BIKE ASSEMBLY

COMFORT 2.0 SHOWN

ASSEMBLY COMPLETE!

Comfort 2.0

Overall Dimension: 120 x 55 x 134 cm Net Weight: 35.5 kg / 78 lbs. Gross Weight: 41 kg / 90 lbs. Max. User Weight: 136 kg / 300 lbs.

Comfort 4.0

Overall Dimension: 120 x 55 x 134 cm Net Weight: 38 kg / 84 lbs. Gross Weight: 43.5 kg / 96 lbs. Max. User Weight: 136 kg / 300 lbs.

Comfort 8.1

Overall Dimension: 120 x 55 x 134 cm Net Weight: 38 kg / 84 lbs. Gross Weight: 43.5 kg / 96 lbs. Max. User Weight: 136 kg / 300 lbs.

BIKE OPERATION

This section explains how to use your bike’s console and programming.

Comfort

2.0

Eingaben

HB H

COMFORT 2.0 CONSOLE OPERATION

Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

A) LCD DISPLAY WINDOWS: Time, Distance, Calories, Speed, RPM, Resistance Level, Heart Rate, Calories, HR Wheel, Workout Profile.

B) ENERGY SAVER: to minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by

mode for 15 mins) and can be quickly woken up with a press of a button.

C) ARROW BUTTONS: used up and down arrow button to select program, set up your console or change resistance while

exercising.

D) ENTER BUTTON: used to confirm setting of workout program or user profile.

START AND STOP BUTTON: press to begin exercising, pause your workout or resume exercising after pause. Hold for 3 seconds

to reset the console.

F) CHANGE DISPLAY BUTTON: used to scroll through display modes and workout feedbacks. Press to switch display column and change

between profile display mode for resistance(upper bar displayed) or watt profile for your current workout watt.(lower bar displayed)

G) AUDIO IN JACK: use to connect with your cellphone or MP3 to play your workout music with integrated speaker.

H) SPEAKER: play music through speakers when connected to your media player.

I) SMART DEVICE AND READING RACK: holds your smart phone, tablet or reaing materials.

Comfort

2.0

Comfort

4.0

Distance

Time

RPM

Zeit

UPM

Entfernung

Speed

Geschwindigkeit

Watts

Level

Watt

Change

Enter

Display

Anzeigenwechsel

Eingabe

Calories

Kalorien

COMFORT 4.0 CONSOLE OPERATION

Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

A) LCD DISPLAY WINDOWS: Time, Distance, Calories, Speed, RPM, Resistance Level, Heart Rate, Calories, Watts, HR

Wheel, Profile.

B) ENERGY SAVER: to minimize energy consumption, your machine will enter energy saver mode automatically (after

entering stand-by mode for 15 mins) and cab be quickly woken up with a touch of a button.

ARROW BUTTONS: used up and down arrow button to select program, set up your console or change resistance

while exercising.

D) ENTER BUTTON: used to confirm setting of workout program or user profile.

E) START AND STOP BUTTON: press to begin exercising, pause your workout or resume exercising after pause. Hold for

3 seconds to reset the console.

F) CHANGE DISPLAY BUTTON: used to scroll through display modes and workout feedbacks. Press to switch display

column and change between profile display mode for resistance(upper bar displayed) or watt profile for your current

workout watt (lower bar displayed).

(Note: use with arrow button up to activate Passport sync process, see page 50 for more details).

G) AUDIO IN JACK: use to connect with your cellphone or MP3 to play your workout music with integrated speaker.

H) SPEAKER: play music through speakers when connected to your media player.

I) SMART DEVICE AND READING RACK: holds your smart phone, tablet or reaing materials.

Comfort

4.0

Comfort

8.1

show

Time

Zeit

Calories

Kalorien

Speed

Geschwindigkeit

Level

Watts

Watt

RPM

UPM

10 15 20

Distance

Entfernung

ENERGY

SAVER

Energiespar-

305

modus

+ 206 hidden pages