TREADMILL OWNER’S MANUAL
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.
PARAGON 5S
PARAGON 7S
PARAGON 7E
PARAGON 8E
32
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises.
To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on the front stabilizer tube and enter it in the space provided
below. Also locate the model name which is next to the serial number.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
WARNI NG
SERIAL NUMBER:
MODEL NAME: HORIZON TREADMILL
54
TOOLS INCLUDED:
5 mm L-Wrench/Screwdriver
6 mm T-Wrench
Screwdriver (not included)
PARTS INCLUDED:
1 Console Assembly
2 Console Masts
3 Hardware Kit
1 Safety Key
1 Power Cord
1 Base Frame
If you have questions or if there are
any missing parts, contact your local
dealer. Contact information may be
located on the back panel of your
manual or on the warranty card.
NEED HELP?
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You
may remove the plastic wrap from console masts.
WARNI NG
UN PACK IN G
Place the treadmill carton on a level flat surface. It is recommended that you place
a protective covering on your floor. Take CAUTION when handling and transporting
this unit. Never open box when it is on its side. Once the banding straps have been
removed, do not lift or transport this unit unless it is fully assembled. Unpack and
assemble the unit where it will be used. Never grab hold of any portion of the incline
frame and attempt to lift or move the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
In case of an emergency, place both hands on the side arm rests to hold
yourself up and place your feed onto the side rail.
WARNI NG
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any
grease, such as lithium bike grease is recommended.
PRE ASSEMBLY
Paragon 5S
Shown
ALL
MODELS
CONSOLE
ON/OFF SWITCH
CIRCUIT BREAKER
POWER CORD
CONS OLE CON TROLS A ND DIS PLAY WI NDOWS
SAFETY KE Y PLACEMENT
ROLLER END C AP
REAR ROLLER TENSION/ADJUSTMENT BOLTS
WATER BOTTLE HOL DER
SPEED/INCLINE TOGGLES
GRIP PULS E HANDRAILS
TRANSPORT WHEEL
READ ING R ACK
HAND LEBARS
CONS OLE MAS T COVE R
MOTOR COVER
CONSOLE MAST
SIDE RAIL
RUNNING BE LT / RUNNING DECK
76
ASSEMBLY STEP 1
A Open HARDWARE PACKAGE 1.
B Pull out the CONSOLE CABLE (1) from the
RIGHT CONSOLE MAST (2).
C Attach RIGHT CONSOLE MAST (2) onto
MAIN FRAME BRACKET (3) and screw with
SHORT BOLT (A), LONG BOLT (B) and ARC
WASHER (C).
D Repeat step C on the other side.
A Carefully slid down the CONSOLE MAST
COVER (4) to right CONSOLE MAST (2).
B
Repeat step A on the other side.
HARDWARE PACKAGE 1
PART TYPE DESCRIPTION QTY
A SHO RT B OLT M8X1. 25PX 20L 2
B LON G BO LT M8X1.25PX60L-20L 4
C ARC WASHE R Φ8.2 2
ASSEMBLY STEP 2
NOTE: Do not fully tighten any bolt before Console
is assmebled in step 2. Be careful not to pinch
console cable when placing the console mast
onto the main frame bracket. You may need extra
help assembling step 1 or 2.
NOTE: Note: Do not assemble CONSOLE MAST
COVER screw at this step.
Paragon 5S
Shown
Paragon 5S
Shown
1
3
2
C
B
A
2
4
98
ASSEMBLY STEP 4
Paragon 5S
Shown
Paragon 5S
Shown
ASSEMBLY STEP 3
A Open HARDWARE PACKAGE 2.
B Gently hold the CONSOLE (5) above the
CONSOLE MAST (2).
C Connect the CONSOLE CABLE (1) from the
CONSOLE MAST (2) to CONSOLE (5).
D Attach the CONSOLE (5) to the CONSOLE
MAST (2) using 6 BOLTS (D), 6 SPRING
WASHERS (E), 2 ARC WASHERS (F) and 4
FLAT WASHERS (G).
A Open HARDWARE PACKAGE 3.
B Use 4 SCREWS (H) to attach LEFT & RIGHT
CONSOLE MAST COVER (4).
HARDWARE PACKAGE 2
PART TYPE DESCRIPTION QTY
D BOLT M 8X1.25 PX20 L 6
E SPRING WASHER Φ8.2 6
F ARC WAS HER Φ8.2 2
G FLAT WASH ER Φ8.2 4
HARDWARE PACKAGE 3
PART TYPE DESCRIPTION QTY
H SCREW M4X30L 4
NOTE: ARC WASHERS to be used at front of
CONSOLE MAST while FLAT WASHERS are used
at side of CONSOLE MAST. You might need extra
help while assembling the CONSOLE at this step.
NOTE: Be careful not to scratch or brake the plastic
while assembling.
2
2
1
D
E
G
F
5
2
2
4
5
H
1110
Paragon 5S
Shown
PAR AGON 5S/ 7S
Overall Dimension : 2026 x 89 5 x 1357 mm /
78” x 35” x 53”
Folding Dimension : 1000 x 89 5 x 1797 mm /
39” x 35” 71”
Max. User Weight : 148 kg / 325 lbs
Net Weight : 106 kg / 233.7 lbs
Gross Weight : 131.5 kg / 289.9 lbs
PAR AGON 7E/8E
Overall Dimension : 2026 x 89 5 x 1357 mm /
78” x 35” x 53”
Folding Dimension : 1000 x 89 5 x 1797 mm /
39” x 35” 71”
Max. User Weight : 159 kg / 350 lbs
Net Weight : 108.5 kg / 239.2 lbs
Gross Weight : 134 kg / 295.4 lbs
ASSEMB LY COM PLETE!
TREADMILL OPERATION
This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the
TREADMILL GUIDE has instructions for the following:
• LOCATION OF THE TRE ADMILL
• USING T HE SAFETY KEY
• FOLDING THE TREADMILL
• MOVIN G THE TREADMILL
• TENSION ING THE RUNNING BELT
• LEVE LING THE TREADMILL
• CENTER ING THE RUNNING BELT
• USING T HE HEART RATE FUNCTION
1312
Paragon 5S
Shown
PARAGON 5S CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) LED DISPLAY WINDOWS: Time, Distance, Speed, Incline, Calories, Heart Rate, Pace, Target Pace,Laps.
B) ENERGY SAVER: To minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by
mode for 15 mins) and could be quickly waken up with a touch of a button.
C) INCLINE KEYS: used to adjust incline in small increments (0.5% Increments).
D) CHANGE DISPLAY BUTTON: used to scroll through display modes. Press to change display feedback during workout.
Under Pacer Program:
in the begin : Time, Calories, Distance
press once : Incline, Heart Rate, Speed
press twice : Pace, Target Pace, Laps
Except Pacer Program:
in the begin : Time, Calories, Distance
press once : Incline, Heart Rate, Speed
press twice : Incline, Heart Rate, Laps
E) START: press to begin exercising, start your workout, or resume exercising after pause.
F) QUICK ADJUST KEYPAD: used to reach desired speed or incline more quickly.
G) SAFETY KEY POSITION: enables treadmill when safety key is inserted.
H) READING RACK: holds reading materials.
I) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.
J) SPEED KEYS: used to adjust speed in small increments (0.1 KM/H increments).
K) QUICK PROGRAM KEYS: used to select a program.
Note: There is no Track LED display, 400m = 1 Lap.
Paragon 5S
Shown
A
CUSTOM
BENUTZER
CLASSIC
KLASSISCH
INCLINE
STEIGUNG
SPEED
GESCHWINDIGKEIT
2 % 4 % 6 %
8 % 10 % 12 %
2
2
km/h
mph
4
3
km/h
mph
8
5
km/h
mph
20
12
km/h
mph
16
10
km/h
mph
12
8
km/h
mph
STOP
HOLD TO RESET
FÜR NULLSTELLUNG
GEDRÜCKT
HALTEN
ENTER
EINGABE
CHANGE
DISPLAY
ANZEIGENWECHSEL
DISTANCE
TARGET
ENTFERNUNGS-
ZIEL
CALORIES
TARGET
KALORIENZIEL
START
QUICK START
SCHNELLSTART
5PARA GON
HRC
PLUS
EnergySaver
ENERGIESPARMODUS
TARGET
ZIEL
PRIME
PREMIUM
B
H
K
C JDGEF FI
TIME
ZEIT
INCLINE
STEIGUNG
PACE
TEMPO
︱
CALORIES
KALORIEN
HEART RATE
HERZFREQUENZ
TARGE T PACE
ZIEL TEMPO
︱
DISTANCE
ENTFERNUNG
SPEED
GESCHWINDIGKEIT
︱
LAPS
RUNDEN
1514
Paragon 7S
Paragon 7E
Shown
Paragon 7S
Paragon 7E
Shown
PARAGON 7E/7S CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) LED DISPLAY WINDOWS: Time, Distance, Speed, Incline, Calories, Heart Rate, Pace, Target Pace,Laps..
B) ENERGY SAVER : To minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by
mode for 15 mins) and could be quickly waken up with a touch of a button.
C) INCLINE KEYS : used to adjust incline in small increments (0.5% Increments).
D) CHANGE DISPLAY BUTTON: used to scroll through display modes. Press to change display feedback during workout.
Under Pacer Program:
in the begin : Time, Calories, Distance
press once : Incline, Heart Rate, Speed
press twice : Pace, Target Pace, Laps
Except Pacer Program:
in the begin : Time, Calories, Distance
press once : Incline, Heart Rate, Speed
press twice : Incline, Heart Rate, Laps
E) START: press to begin exercising, start your workout, or resume exercising after pause.
F) QUICK ADJUST KEYPAD : used to reach desired speed or incline more quickly.
G) SAFETY KEY POSITION: enables treadmill when safety key is inserted.
H) READING RACK : holds reading materials.
I) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.
J) SPEED KEYS : used to adjust speed in small increments (0.1 KM/H increments).
K) QUICK PROGRAM KEYS : used to select a program.
L) LED TRACK: displays workout circle, one circle means 400 meter.
M) PASSPORT QUICK KEY: used to connect Passport. Press and sync with Passport.
CUSTOM
BENUTZER
CLASSIC
KLASSISCH
HRC
INCLINE
STEIGUNG
SPEED
GESCHWINDIGKEIT
STOP
HOLD TO RESET
FÜR NULLSTELLUNG
GEDRÜCKT
HALTEN
ENTER
EINGABE
CHANGE
DISPLAY
ANZEIGENWECHSEL
DISTANCE
TARGET
ENTFERNUNGS-
ZIEL
CALORIES
TARGET
KALORIENZIEL
START
QUICK START
SCHNELLSTART
2 % 4 % 6 %
8 % 10 % 12 %
2
2
km/h
mph
4
3
km/h
mph
8
5
km/h
mph
20
12
km/h
mph
16
10
km/h
mph
12
8
km/h
mph
7PARA GON
PLUS
TARGET
ZIEL
PRIME
PREMIUM
EnergySaver
ENERGIESPARMODUS
C JDGEF FI
A
B
M
L
H
K
TIME
ZEIT
INCLINE
STEIGUNG
PACE
TEMPO
︱
CALORIES
KALORIEN
HEAR T RAT E
HERZFREQUENZ
TARGE T PACE
ZIEL TEMPO
︱
DISTANCE
ENTFERNUNG
SPEED
GESCHWINDIGKEIT
︱
LAPS
RUNDEN
1716
Paragon 8E
Shown
Paragon 8E
Shown
CUSTOM
BENUTZER
CLASSIC
KLASSISCH
TARGET
ZIEL
HRC
INCLINE
STEIGUNG
SPEED
GESCHWINDIGKEIT
STOP
HOLD TO RESET
FÜR NULLSTELLUNG
GEDRÜCKT
HALTEN
ENTER
EINGABE
CHANGE
DISPLAY
ANZEIGENWECHSEL
DISTANCE
TARGET
ENTFERNUNGS-
ZIEL
CALORIES
TARGET
KALORIENZIEL
START
QUICK START
SCHNELLSTART
2 % 4 % 6 %
8 % 10 % 12 %
2
2
km/h
mph
4
3
km/h
mph
8
5
km/h
mph
20
12
km/h
mph
16
10
km/h
mph
12
8
km/h
mph
SPEED
GESCHWINDIGKEIT
HEAR T RAT E
HERZFREQUENZ
DISTANCE
ENTFERNUNG
LAPS
RUNDEN
EnergySaver
ENERGIESPARMODUS
8PARA GON
PRIME
PREMIUM
PLUS
C JDGEF FI
B
M
H
A
K
ANL
TIME
ZEIT
PACE
TEMPO
INCLINE
STEIGUNG
TARGE T PACE
ZIEL TEMPO
CALORIES
KALORIEN
︱
PARAGON 8E CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) LED DISPLAY WINDOWS: Time, Distance, Speed, Incline, Calories, Heart Rate, Pace, Target Pace, Laps.
B) ENERGY SAVER : To minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by
mode for 15 mins) and could be quickly waken up with a touch of a button.
C) INCLINE KEYS : used to adjust incline in small increments (0.5% Increments).
D) CHANGE DISPLAY BUTTON: used to scroll through display modes. Press to change display feedback during workout.
Under Pacer Program:
in the begin : Time, Incline, Distance, Speed
press once : Time, Calories, Laps, Heart Rate
press twice : Pace, Target Pace, Laps, Heart Rate
Except Pacer Program:
in the begin : Time, Incline, Distance, Speed
press once : Time, Calories, Laps, Heart Rate
E) START: press to begin exercising, start your workout, or resume exercising after pause.
F) QUICK ADJUST KEYPAD : used to reach desired speed or incline more quickly.
G) SAFETY KEY POSITION: enables treadmill when safety key is inserted.
H) READING RACK : holds reading materials.
I) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.
J) SPEED KEYS : used to adjust speed in small increments (0.1 KM/H increments).
K) QUICK PROGRAM KEYS : used to select a program.
L) DOT-MATRIX DISPLAY WINDOW: displays workout level, progress and workout profiles.
M) PASSPORT QUICK KEY: used to connect Passport. Press and sync with Passport.
N) POWER BUTTOM: used to power on/off console and also the console will into Energy Saver Mode when power off console.
1918
• HEART RATE: Shown as BPM (beats per minute). Used
to monitor your heart rate (displayed when contact is made
with both pulse grips).
• LAPS: Shows how many laps have you completed
• PACE: Indicates how many minutes it takes to complete
a KM while running or walking at your current speed.
For example : If at your current speed it will take you 10
minutes to complete a KM, the treadmill will display “10:00”
as your pace.
• TARGET PACE: Means your target time to reach a KM.
• ENERGY SAVER: Indicates when the machine is in Energy
Saver mode to conserve power consumption
• TIME: Shown as minutes : seconds. View the time
remaining or the time elapsed in your workout.
• DISTANCE: Shown as km or miles. Indicates distance
traveled or distance remaining during your workout.
• SPEED: Shown as MPH or KM/H. Indicates how fast
your walking or running surface is moving.
• INCLINE: Shown as percent. Indicates the incline of
your walking or running surface.
• CALORIES: Total calories burned or calories
remaining left to burn during your workout.
PARAGON 5S DISPLAYS
DISPLAY WINDOWS
Paragon 5S
Shown
• TRACK: Shows your progress of your current lap (400M
circle run).
• LAPS:
Shows how many laps have you completed.
•
PACE: Indicates how many minutes it takes to complete a KM
while running or walking at your current speed. For example :
If at your current speed it will take you 10 minutes to complete
a KM, the treadmill will display “10:00” as your pace.
• TARGET PACE:
Means your target time to reach a KM.
•
ENERGY SAVER: Indicates when the machine is in Energy
Saver mode to conserve power consumption
•
PASSPORT QUICK KEY: used to connect Passport. Press
and sync with Passport.
DISPLAY WINDOWS
• TIME: Shown as minutes : seconds. View the time
remaining or the time elapsed in your workout.
• DISTANCE: Shown as km or miles. Indicates distance
traveled or distance remaining during your workout.
• SPEED: Shown as MPH or KM/H. Indicates how fast
your walking or running surface is moving.
• INCLINE: Shown as percent. Indicates the incline of
your walking or running surface.
• CALORIES: Total calories burned or calories
remaining left to burn during your workout.
• HEART RATE: Shown as BPM (beats per minute).
Used to monitor your heart rate (displayed when
contact is made with both pulse grips).
PARAGON 7S/7E DISPLAYS
Paragon 7S
Paragon 7E
Shown
EnergySaver
ENERGIESPARMODUS
TIME
ZEIT
INCLINE
STEIGUNG
PACE
TEMPO
︱
CALORIES
KALORIEN
HEART RATE
HERZFREQUENZ
TARGET PACE
ZIEL TEMPO
︱
DISTANCE
ENTFERNUNG
SPEED
GESCHWINDIGKEIT
︱
LAPS
RUNDEN
EnergySaver
ENERGIESPARMODUS
TIME
ZEIT
INCLINE
STEIGUNG
PACE
TEMPO
︱
CALORIES
KALORIEN
HEART RATE
HERZFREQUENZ
TARGET PACE
ZIEL TEMPO
︱
DISTANCE
ENTFERNUNG
SPEED
GESCHWINDIGKEIT
︱
LAPS
RUNDEN
2120
• DOT-MATRIX LED WINDOW (16 × 16): To display
Program name, Program profiles and communication text.
• LAPS:
Shows how many laps have you completed.
•
PACE: Indicates how many minutes it takes to complete a KM
while running or walking at your current speed. For example :
If at your current speed it will take you 10 minutes to complete
a KM, the treadmill will display "10:00" as your pace.
• TARGET PACE:
Means your target time to reach a KM.
•
ENERGY SAVER: Indicates when the machine is in Energy
Saver mode to conserve power consumption
•
PASSPORT QUICK KEY: used to connect Passport. Press
and sync with Passport.
• TIME: Shown as minutes : seconds. View the time
remaining or the time elapsed in your workout.
• DISTANCE: Shown as km or miles. Indicates distance
traveled or distance remaining during your workout.
• SPEED: Shown as MPH or KM/H. Indicates how fast
your walking or running surface is moving.
• INCLINE: Shown as percent. Indicates the incline of
your walking or running surface.
• CALORIES: Total calories burned or calories
remaining left to burn during your workout.
• HEART RATE: Shown as BPM (beats per minute).
Used to monitor your heart rate (displayed when
contact is made with both pulse grips).
DISPLAY WINDOWS
Paragon 8E
Shown
GETTING STARTED
1) Check to make sure no objects are placed on the belt that will hinder the movement of the treadmill.
2) Plug in the power cord and turn the treadmill ON.
3) Stand on the side rails of the treadmill.
4) Attach the safety key clip to part of your clothing making sure that it is secure and will not become detached during operation.
5) Insert the safety key into the safety keyhole in the console.
6) You have two options to start your workout:
A) QUICK START UP
Simply press the START key to begin working out.
B) SELECT A PROGRAM
1) Select GUEST or USER using +/- button and press ENTER to confirm.
2) Change program setup using +/- button or quick adjust keypads and press ENTER to go through setup.
3) When setup is complete, press START to begin your workout.
RESET THE CONSOLE
Hold STOP key for 3 seconds.
FINISHING YOUR WORKOUT
When your workout is complete, on 5S/7S/7E Console, it will show TIME, DISTANCE, CALORIES as default, you can press
ENTER/CHANGE DISPLAY once to show other information such as INCLINE, HEART RATE and SPEED. On 8E Console, it
will show TIME, DISTANCE, INCLINE, SPEED and Dot-Matrix LED will show SPEED profile as default, press ENTER/CHANGE
DISPLAY to change to INCLINE profile.
ALL
MODELS
PARAGON 8E DISPLAYS
SPEED
GESCHWINDIGKEIT
HEA RT R ATE
HERZFREQUENZ
DISTANCE
ENTFERNUNG
LAPS
RUNDEN
EnergySaver
ENERGIESPARMODUS
TIME
ZEIT
PACE
TEMPO
INCLINE
STEIGUNG
CALORIES
KALORIEN
TARGET PACE
ZIEL TEMPO
︱
2322
1) MANUAL: Adjust your speed and incline manually during your workout.
2) INTERVALS / SPEED INTERVALS: Walk or run a series of alternating speed levels. Time-based goal with 10 difficulty
levels to choose from. Warm-up and cool down last 4:00 minutes each and are included in program times.
PROGRAM INFORMATION
NOTE:
Paragon 5S contains 10 programs
: Manual, Speed Intervals, Weight Loss, Custom, Pacer, 800M, 5K, 100 Kcal, 500 Kcal, HRC Incline.
Paragon 7S/7E contains 16 programs
: Manual, Speed Intervals, Weight Loss, Mountain Climb, Custom 1, Custom 2,
Pacer, Fit Test, 800M, 5K, 10K, 100 Kcal, 300 Kcal, 500 Kcal, HRC Speed, HRC Incline.
Paragon 8E contains 22 programs
: Manual, Speed Intervals, Peak Intervals, Weight Loss, Hill Run, Mountain Climb, Random,
Custom 1, Custom 2, Pacer, Fit Test, 800M, 5K, 10K, Half Marathon, 100 Cal, 300 Kcal, 500 Kcal, 700 Kcal, HRC Speed, HRC
Incline, HRC Interval.
If speed or incline are changed during your workout, the remaining segments will be affected accordingly.
ALL
MODELS
ALL
MODELS
3) PEAK INTERVALS (PARAGON 8E ONLY): Walk or run a series of alternating speed and incline levels. Time-based goal
with 10 difficulty levels to choose from. This program allows to adjust your speed and incline manually during workout.
Peak Intervals - Speed and Incline changes
Segments Warm-Up 1 2 Cool Down
Time 4:00
min 90 sec 30 sec 4:00 min
Level 1
Speed(MPH) 1 1.5 2 4 1.5 1
Speed(KM/H) 1.6 2.4 3. 2 6.4 2.4 1.6
Incline 1 1. 5 0.5 1.5 1.5 0
Level 2
Speed(MPH) 1 1.5 2 4.5 1.5 1
Speed(KM/H) 1.6 2.4 3. 2 7.2 2.4 1.6
Incline 1.5 2.5 3 6.5 2.5 1.5
Level 3
Speed(MPH) 1. 3 1.9 2.5 5 1.9 1.3
Speed(KM/H) 2.1 3 4 8 3 2.1
Incline 2 3 4 7.5 3 2
Level 4
Speed(MPH) 1. 3 1.9 2.5 5.5 1.9 1.3
Speed(KM/H) 2.1 3 4 8.8 3 2.1
Incline 2 3 4 8.5 3 2
Level 5
Speed(MPH) 1. 5 2.3 3 6 2.3 1.5
Speed(KM/H) 2.4 3.7 4.8 9.6 3.7 2.4
Incline 2.5 3.5 4. 5 9 3.5 2.5
Level 6
Speed(MPH) 1. 5 2.3 3 6.5 2.3 1.5
Speed(KM/H) 2.4 3.7 4.8 10.4 3.7 2.4
Incline 2.5 3.5 4. 5 10 3.5 2.5
Level 7
Speed(MPH) 1. 8 2.6 3.5 7 2.6 1.8
Speed(KM/H) 2.9 4.2 5.6 11 .2 4.2 2.9
Incline 2.5 4 5.5 10.5 4 3
Level 8
Speed(MPH) 1. 8 2.6 3.5 7.5 2.6 1.8
Speed(KM/H) 2.9 4.2 5.6 12 4.2 2.9
Incline 3 4 5.5 11.5 4 3
Level 9
Speed(MPH) 2 3 4 8 3 2
Speed(KM/H) 3.2 4.8 6.4 12. 8 4.8 3.2
Incline 3 4.5 6 12 5 3
Level 10
Speed(MPH) 2 3 4 8.5 3 2
Speed(KM/H) 3.2 4.8 6.4 13 .6 4.8 3.2
Incline 3 4.5 6 12 5 3
Speed Intervals - Speed only
Segments Warm-Up 1 2 Cool Down
Time 4:00
min 90 sec 30 sec 4:00 min
Level 1
Speed(MPH) 1 1.5 2 4 1.5 1
Speed(KM/H) 1.6 2.4 3. 2 6.4 2.4 1.6
Level 2
Speed(MPH) 1 1.5 2 4.5 1.5 1
Speed(KM/H) 1.6 2.4 3. 2 7.2 2.4 1.6
Level 3
Speed(MPH) 1. 3 1.9 2.5 5 1.9 1.3
Speed(KM/H) 2.1 3 4 8 3 2.1
Level 4
Speed(MPH) 1. 3 1.9 2.5 5.5 1.9 1.3
Speed(KM/H) 2.1 3 4 8.8 3 2.1
Level 5
Speed(MPH) 1. 5 2.3 3 6 2.3 1.5
Speed(KM/H) 2.4 3.7 4.8 9.6 3.7 2.4
Level 6
Speed(MPH) 1. 5 2.3 3 6.5 2.3 1.5
Speed(KM/H) 2.4 3.7 4.8 10.4 3.7 2.4
Level 7
Speed(MPH) 1. 8 2.6 3.5 7 2.6 1.8
Speed(KM/H) 2.9 4.2 5.6 11 .2 4.2 2.9
Level 8
Speed(MPH) 1. 8 2.6 3.5 7.5 2.6 1.8
Speed(KM/H) 2.9 4.2 5.6 12 4.2 2.9
Level 9
Speed(MPH) 2 3 4 8 3 2
Speed(KM/H) 3.2 4.8 6.4 12. 8 4.8 3.2
Level 10
Speed(MPH) 2 3 4 8.5 3 2
Speed(KM/H) 3.2 4.8 6.4 13 .6 4.8 3.2
2524
ALL
MODELS
ALL
MODELS
4) WEIGHT LOSS: Promotes weight loss by increasing and decreasing the speed and incline, while keeping you in your fat
burning zone. Speed and Incline changes, segments repeat every 30 seconds.
5) HILL RUN (PARAGON 8E ONLY) : Simulates a hill running.This program helps tone muscle and improve cardiovascular
ability. speed changes and segments repeat every 30 seconds.
Weight Loss (Weight Loss 1) - Speed and Incline changes
Segments Warm-Up 1 2 3 4 5 6 7 8 Cool Down
Time 4:00
min 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 4:00 min
Level 1
Incline 0 0.5 1.5 1.5 1 0.5 0. 5 0. 5 1 1.5 0.5 0
Speed(MPH) 1 1.5 2 2.5 3 3.5 4 3.5 3 2.5 2.3 1.5
Speed(KM/H) 1.6 2.4 3. 2 4 4.8 5.6 6. 4 5.6 4.8 4 3.7 2.4
Level 2
Incline 0 0.5 1.5 1.5 1 0.5 1 0.5 1 1.5 0.5 0
Speed(MPH) 1. 3 1.9 2.5 3 3.5 4 4.5 4 3.5 3 2.6 1.8
Speed(KM/H) 2.1 3 4 4. 8 5.6 6.4 7. 2 6.4 5.6 4.8 4.2 2.9
Level 3
Incline 0.5 1 2 2 1.5 1 1 1 1.5 2 1 0.5
Speed(MPH) 1. 5 2.3 3 3.5 4 4.5 5 4.5 4 3.5 3 2
Speed(KM/H) 2.4 3.7 4.8 5.6 6.4 7. 2 8 7.2 6.4 5.6 4. 8 3. 2
Level 4
Incline 0.5 1 2 2 1.5 1 1 1 1.5 2 1 0.5
Speed(MPH) 1. 8 2.6 3.5 4 4.5 5 5.5 5 4.5 4 3.4 2.3
Speed(KM/H) 2.9 4.2 5.6 6.4 7.2 8 8.8 8 7.2 6.4 5.4 3.7
Level 5
Incline 1 1. 5 2.5 2.5 2 1.5 1.5 1.5 2 2.5 1.5 1
Speed(MPH) 2 3 4 4.5 5 5.5 6 5.5 5 4.5 3.8 2.5
Speed(KM/H) 3.2 4.8 6.4 7.2 8 8.8 9.6 8.8 8 7. 2 6.1 4
Level 6
Incline 1 1. 5 2.5 2.5 2 1.5 1.5 1.5 2 2.5 1.5 1
Speed(MPH) 2.3 3.4 4.5 5 5.5 6 6.5 6 5.5 5 4 .1 2.8
Speed(KM/H) 3.7 5.4 7.2 8 8.8 9.6 10 .4 9.6 8.8 8 6.6 4. 5
Level 7
Incline 1.5 2 3 3 2.5 2 2 2 2.5 3 2 1.5
Speed(MPH) 2.5 3.8 5 5.5 6 6.5 7 6.5 6 5.5 4.5 3
Speed(KM/H) 4 6 .1 8 8.8 9.6 10.4 11.2 10.4 9.6 8.8 7. 2 4.8
Level 8
Incline 1.5 2 3 3 2.5 2 2 2 2.5 3 2 1.5
Speed(MPH) 2.8 4.1 5.5 6 6.5 7 7.5 7 6.5 6 4.9 3.3
Speed(KM/H) 4.5 6.6 8.8 9.6 10.4 11.2 12 11 .2 10.4 9.6 7. 8 5.3
Level 9
Incline 2 2.5 3.5 3.5 3 2.5 2.5 2.5 3 3.5 2.5 2
Speed(MPH) 3 4.5 6 6.5 7 7. 5 8 7.5 7 6.5 5.3 3.5
Speed(KM/H) 4.8 7. 2 9.6 10.4 11. 2 12 12 .8 12 11.2 10.4 8.5 5.6
Level 10
Incline 2 2.5 3.5 3.5 3 2.5 2.5 2.5 3 3.5 2.5 2
Speed(MPH) 3.3 4.9 6.5 7 7.5 8 8.5 8 7.5 7 5.6 3.8
Speed(KM/H) 5.3 7. 8 10.4 11 .2 12 12.8 13 .6 12.8 12 11. 2 9 6.1
Hill Run - Speed only
Segments Warm-Up 1 2 3 4 5 6 7 8 Cool Down
Time 4:00
min 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 4:00 min
Level 1
Speed(MPH) 1 1.5 2 2.5 3 3.5 4 3.5 3 2.5 2.3 1.5
Speed(KM/H) 1.6 2.4 3. 2 4 4.8 5.6 6. 4 5.6 4.8 4 3.7 2.4
Level 2
Speed(MPH) 1. 3 1.9 2.5 3 3.5 4 4.5 4 3.5 3 2.6 1.8
Speed(KM/H) 2.1 3 4 4. 8 5.6 6.4 7. 2 6.4 5.6 4.8 4.2 2.9
Level 3
Speed(MPH) 1. 5 2.3 3 3.5 4 4.5 5 4.5 4 3.5 3 2
Speed(KM/H) 2.4 3.7 4.8 5.6 6.4 7. 2 8 7.2 6.4 5.6 4. 8 3. 2
Level 4
Speed(MPH) 1. 8 2.6 3.5 4 4.5 5 5.5 5 4.5 4 3.4 2.3
Speed(KM/H) 2.9 4.2 5.6 6.4 7.2 8 8.8 8 7.2 6.4 5.4 3.7
Level 5
Speed(MPH) 2 3 4 4.5 5 5.5 6 5.5 5 4.5 3.8 2.5
Speed(KM/H) 3.2 4.8 6.4 7.2 8 8.8 9.6 8.8 8 7. 2 6.1 4
Level 6
Speed(MPH) 2.3 3.4 4.5 5 5.5 6 6.5 6 5.5 5 4 .1 2.8
Speed(KM/H) 3.7 5.4 7.2 8 8.8 9.6 10 .4 9.6 8.8 8 6.6 4. 5
Level 7
Speed(MPH) 2.5 3.8 5 5.5 6 6.5 7 6.5 6 5.5 4.5 3
Speed(KM/H) 4 6 .1 8 8.8 9.6 10.4 11. 2 10.4 9.6 8.8 7.2 4.8
Level 8
Speed(MPH) 2.8 4.1 5.5 6 6.5 7 7.5 7 6.5 6 4.9 3.3
Speed(KM/H) 4.5 6.6 8.8 9.6 10. 4 11.2 12 11 .2 10.4 9.6 7. 8 5.3
Level 9
Speed(MPH) 3 4.5 6 6.5 7 7. 5 8 7.5 7 6.5 5.3 3.5
Speed(KM/H) 4.8 7. 2 9.6 10.4 11. 2 12 12 .8 12 11.2 10.4 8.5 5.6
Level 10
Speed(MPH) 3.3 4.9 6.5 7 7.5 8 8.5 8 7.5 7 5.6 3.8
Speed(KM/H) 5.3 7. 8 10.4 11 .2 12 12.8 13 .6 12.8 12 11. 2 9 6.1
Level 11
Speed(MPH) 3 4.5 7 7.5 8 8.5 9 8.5 8 7. 5 5.3 3.5
Speed(KM/H) 4.8 7. 2 11 .2 12 12.8 13 .6 14.4 13.6 12. 8 12 8.5 5.6
Level 12
Speed(MPH) 3.3 4.9 7.5 8 8.5 9 9.5 9 8.5 8 5.6 3.8
Speed(KM/H) 5.3 7. 8 12 12.8 13. 6 14.4 15.2 14.4 13. 6 12.8 9 6.1
2726
6) MOUNTAIN CLIMB (PARAGON 7S/7E/8E ONLY): A more intense version of MOU NTAIN CLIM B. Simulates a mountain
ascent and descent. This program helps tone muscle and improve cardiovascular ability. Incline changes and segments repeat
every 30 seconds.
Mountain Climb - Incline Only
Segments Warm-Up 1 2 3 4 5 6 7 8 9 10 Cool Down
Time 4:00
min 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 4:00 min
Level 1 0 0 1 1.5 2 2.5 3 3 2.5 2 1.5 1 0 0
Level 2 0 0 1.5 2 2.5 3 3.5 3.5 3 2.5 2 1. 5 0 0
Level 3 0 1 2 2.5 3 3.5 4 4 3.5 3 2.5 2 1 0
Level 4 0 1.5 2.5 3 3.5 4 4.5 4.5 4 3.5 3 2.5 1.5 0
Level 5 0 1.5 3 3.5 4 4.5 5 5 4.5 4 3.5 3 1.5 0
Level 6 0 1.5 3.5 4 4. 5 5 5.5 5.5 5 4.5 4 3.5 1.5 0
Level 7 0 1.5 4 4.5 5 5.5 6 6 5.5 5 4.5 4 1.5 0
Level 8 0 2 4.5 5 5.5 6 6.5 6.5 6 5.5 5 4.5 2 0
Level 9 0 2 5 5.5 6 6.5 7 7 6.5 6 5.5 5 2 0
Level 10 0 2 5.5 6 6.5 7 7.5 7. 5 7 6.5 6 5.5 2 0
7) RANDOM : Random is a program that will give you a different workout every time you enter. The incline level will change
randomly.
Random
Warm-Up Program Segments - Rrepeat Cool Down
Seconds 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60
Level 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
1 1 1 2 2 1 4 3 5 2 7 4 1 6 3 1 1 1 1
2 1 2 2 3 2 5 4 6 3 8 5 2 7 4 2 1 1 1
3 2 2 3 3 3 6 5 7 4 9 6 3 8 5 2 1 1 1
4 2 3 3 4 4 7 6 8 5 10 7 4 9 6 3 1 1 1
5 3 4 4 4 5 8 7 9 6 11 8 5 10 7 3 3 2 1
6 3 5 4 5 6 9 8 10 7 12 9 6 11 8 4 3 2 1
7 4 5 5 5 7 10 9 11 8 12 10 7 12 9 4 3 2 1
8 4 5 5 5 8 11 10 12 9 12 11 8 12 10 4 3 2 1
9 4 5 5 5 9 12 11 12 10 12 12 9 12 11 5 4 3 1
10 4 5 6 6 10 12 12 12 11 12 12 10 12 12 5 4 3 1
8) CUSTOM PROGRAMS: (PARAGON 5S preset program: CUSTOM 1; PARAGON 7S/7E preset program: CUSTOM 1 &
CUSTOM 2; PARAGON 8E preset program: CUSTOM 1 & CUSTOM 2).
Lets you create and reuse a perfect workout for you with specific speed, incline and time combination. The ultimate in personal
programming. Time-based goal.
1) Select CUSTOM 1, CUSTOM 2 using +/- and press enter on the programming button .
2) Select WEIGHT using +/- and press enter on the programming button .
3) Select TIME using +/- and press enter on the programming button .
4) Select SPEED for segments 1 through 15 using +/- and press enter to set each segment.
5) Select INCLIN E for segments 1 through 15 using +/- and press enter to set each segment.
6) Press START to begin exercising. At this time, your program has been successfully saved into memory and can be used for
future workouts.
NOTE:
• While using your saved program, you are able to adjust the speed or incline, but any changes will not be saved.
• To reset the memory, press and hold enter for 5 seconds.
9) PACE: Trains you to run at a steady “race pace”. Enter in the distance plus the time limit, and the program calculates a steady pace.
10) FIT TEST (PARAGON 7S/7E/8E ONLY): A workout based on the Gerkin protocol. This test has various stages increasing
treadmill speed and incline until your max. heart rate is reached. Your score is based on your gender, age, and
time needed to complete the test.
WARM-UP : 3 minutes long at 1.6 - 4.8 km/h / 1.0 - 3.0 mph and 0% incline.
STAGE 1 : 1 minute long at 7.2 km/h / 4.5 mph and 0% incline.
STAGE 2 : 1 minute long at 7.2 km/h / 4.5 mph and 2% incline.
STAGE 3 : 1 minute long at 8.0 km/h / 5.0 mph and 2% incline.
STAGE 4 THOUGH 17 : After every odd minute, the incline will increase by 2%. After every even minute, the speed will increase
by 0.5 mph(0.8km/h). Once the user’s heart rate exceeds the target heart rate (85% of maximum as determined by the equation
[220 - age] x [0.85] = target heart rate), the evaluation ends and the final evaluation stage is recorded.
COOL-DOWN : The test is completed when user’s heart rate exceeds the target or the users completes all 17 stages,
whichever occurs first. Then the treadmill will enter cool down for 3 minutes.
2928
ALL
MODELS
ALL
MODELS
11) DISTANCE TARGET (PARAGON 5S PRESET PROGRAM:800M, 5K; PARAGON 7S/7E PRESET PROGRAM: 800M,
5K, 10K; PARAGON 8E PRESET PROGRAM: 800M, 5K, 10K, HALF MARATHON): Distance-based program. Calculates
targets distances from your MCU and continues until program goal is reached.
12) CALORIES TARGET (PARAGON 5S PRESET PROGRAM: 100 KCAL, 500 KCAL; PARAGON 7S/7E PRESET
PROGRAM: 100 KCAL, 300 KCAL, 500 KCAL; PARAGON 8E PRESET PROGRAM: 100 KCAL, 300 KCAL, 500 KCAL,
700 KCAL ) : A workout that allows you to select a specific number of calories you would like to burn during your workout.
Increasing the calories goal of the workout will increase the duration of the workout.
13) HRC ( SPEED, INCLINE, INTERVAL ) (PARAGON 5S PRESET PROGRAM: HRC INCLINE; PARAGON 7S/7E PRESET
PROGRAM: HRC SPEED, HRC INCLINE; PARAGON 8E PRESET PROGRAM: HRC SPEED, HRC INCLINE, HRC INTERVAL)
HR Speed : Program adjusts spped to bring to your target heart rate.
HR Incline : Program adjusts incline to bring to your target heart rate.
HR Interval : Program adjusts speed and incline to bring to your target heart rate.
HEART RATE TRAINING
The first step in knowing the right intensity for your
training is to find out your maximum heart rate (max HR
= 220 – your age). The agebased method provides
an average statistical prediction of your max HR and
is a good method for the majority of people, especially
those new to heart rate training. The most precise and
accurate way of determining your individual max HR is
to have it clinically tested by a cardiologist or exercise
physiologist through the use of a maximal stress test.
If you are over the age of 40, overweight, have been
sedentary for several years, or have a history of heart
disease in your family, clinical testing is recommended.
This chart gives examples of the heart rate range for a
30 year old exercising at 5 different heart rate zones.
For example, a 30-year-old’s max HR is 220 – 30 = 190 bpm and 90% max H R is 190 × 0.9 = 171 bpm.
Target Heart
Rate Zone
Workout
Duration
Example THR
Zone (age 30)
Your
THR Zone
Recommended For
VERY HARD
90
– 100%
< 5 min 171 – 190 bpm
Fit persons and for athletic
training
HARD
80 – 90%
2 – 10 min 152 – 171 bpm Shorter workouts
MODERATE
70 – 80%
10 – 40 min 133 – 152 bpm Moderately long workouts
LIGHT
60 – 70%
40 – 80 min 114 – 133 bpm
Longer and frequently repeated
shorter exercises
VERY LIGHT
50 – 60%
20 – 40 min 104 – 114 bpm
Weight management and active
recovery
Your target heart rate should be set at a number that you will be able to exercise at throughout the majority of your workout. Once you
have chosen your target heart rate, press the ‘Start’ button and begin your workout.
• There is a 4-minute warm-up built into this program at level 1 incline.
• After 4 minutes, the incline will gradually adjust to bring your heart rate ( within +/- 5 beats ) of the target number you selected at
the beginning of the program.
• Once the user is at the target heart rate zone (plus or minus 5 beats), the elevation level will remain at the current resistance level.
• If there is no heart rate detected, the unit will not change incline levels up or down.
• If the user is more than 25 beats per minute above the target heart rate zone, the console will shut down for safety reasons.
NOTE:
• The chest strap is required to use the HRC program, with HRC program you can only choose time as your workout target.
• Target heart rate is selected in multiples of 5 beats.
• The large dot matrix window displays your heart rate during exercise. The middle row represents your target heart rate (THR) and
the other rows equal +/-2 heart beats. If you are working out beneath your THR, the LEDs below the middle row will illuminate.
If you are over, the display LCD/LED above the middle row will illuminate. Your current heart rate is represented by the flashing
column and the window will refresh every 5 seconds.
3130
ENERGY SAVER (STANDBY MODE)
This machine has an energy saver mode. The display will automatically enter standby mode (energy saver mode) after 15
minutes of inactivity after paused. (Also You can press the Power Button into Energy Saver mode instantly, only in Paragon
8E.) Almost all power for the machine will be off except for some circuits that are needed to detect a key press, indicating the
console should “wake up”.
ALL
MODELS
SYNCING TREADMILL WITH PASSPORT (PARAGON 7S / 7E / 8E ONLY)
1) Use the arrow keys on the Passport remote to scroll to the setup icon and press select.
2) Follow the on-screen prompt to press and hold the incline up and stop buttons on the console.
3) Once your snyc is success, your treadmill message bar will change from RF Sync to Passport ready.
4) Besides point 3, the message displayed on-screen will notify you if the sync was a success or failure.
NOTE: See Passport Owner’s Manual for more information.
PARAGON 5S EXPLODED VIEW
3332
NO. DESCRIPTION
1 MOTOR SET;MOTOR;TM482;
2 CONSOLE SET;CONSOLE;TM482;
AB1 FRAME SET-EXREAWORK;SCREEN PRINT;TM48
AH1 ELEVATION SUPT RACK SET;PAINTING;MM384
AK1 BASE FRAME SET;PAINTING;MM384;TM480-2
AQ1 SHIELD SET;CONSOLE MAST;LEFT DOWN;TM480
AQ2 SHIELD SET;CONSOLE MAST;RIGHT DOWN;TM48
AR1 RO LLER SET;FRONT;TEXTUR E;TM136
AR2 ROLLER S ET;REAR;Φ46;TM59
B29 AIR STICK;SLOW-DROP;400N;JOURNEY350MM;
B30 EL ASTOMER;RUNN ING DECK;Φ30X37X 26;TM41
B31 FINISHED TREADMILL DECK;600X1340X18T;SI
B32 ELASTOMER
B34 BELT GUIDE
B35 SCR EW;BH;ΦX5X12L;TC;PH;BED;POT;
B36 SC REW;FH;M8X1.25PX30L ;HS;
B37 NUT;NLK;M8X1.25P;BZN;
B38 SI DE RAIL FIXIN G PLATE;MM384- DARK SI
B39 SCRE W;TRH;ΦX4X15L;TC;PH;BED;POT;
B41 SCREW;BH;M8X1.25PX30L;HS;BAN;
B45 WASHER;FL AT;ΦX8.2XΦX15.0X1.2T;BED;ROHS
B46 EL ASTOMER BLACK 9 0
B49 STOPPER;PAINTING;BLACK2;TM480;
B66 SLEEV E;Φ22.2X1.0TX22L;TM27
C01 CONSOLE MAST-EXTRAWORK;LEFT;SCREEN PRIN
C02 CONSOLE MAST-EXTRAWORK;RIGHT;SCREEN PRI
NO. DESCRIPTION
H10 WASH ER;F LT;Φ1 0.5 XΦ18 .0X 2.6 T;
H30 SCREW;M8X1.25PX26L-10L;20CR;BAN;SP
H31 WASHER;FLT;Φ10.5XΦ20.0X1.0T;TFN;
H32 WASHER;FL AT;ΦX10.2XΦX20.0X1.0T;BL ZN;R
H33 WASHER;FL AT;Φ10.5XΦ20.0X2.0T;ZINC;
H36 SNA P RING;EXTERNAL C-SHAPED;S-10;BLACK
H37 RU BBER STOPPER;AC003;TM16
K11 CONNECT PLATE;MM384-DARK SILVER;TM48
K14 SCREW;M8X1.25PX12L-6L;BZN;P-T
K15 SPRING;EXT;Φ2.0XΦ16.0X50.0LX12N;
K17 SCREW;BH;M10X1.5PX40L;HS;BP
K19 SCREW;FH;M8X1.25PX4 5L-15L;HS;BZN;P-T
K20 SCR EW;BH;M8X15L;HS;BZN;BP;G8.8;
K23 SC REW;FH;M4XX40L;PH;BED;
K25 BRAKE LOCATION SET;TM332
K27 FOOT PAD;ADJUST;RUBBER;W3/8-16UNC;FMW38A
K28 RVN;ALS7-616 -150(0.02 -0.15);YZN;
K30 WASHER;FLT;Φ8.5XΦ19.0X2.0T;BZN;
K31 HOOK BASE;PAINTING;MM384;TM480;
K35 ADJUSTABLE FOOT PAD NUT
L01 FRONT CARRIAGE RO LLER; NYLON PA6;Φ46XΦ10
L02 WHEEL MOBILE FRA ME BASE
L05 WHEEL;NYLON;Φ74;TM27
L06 TRANSPORT WHEEL
L07 WASHER;FLT;Φ10.5XΦ20.0X2.0T;BZN;
L09 SCREW;HEX;M6X1.0PX25L;
NO. DESCRIPTION
L17 LOCATION HOOK;PAINTING;MM384;TM480;
L21 SCRE W;SH; M6X1.0 PX10L; HS;B ZN;
L25 WASHER;SPRING LOCK;ΦX6.1XΦX10.0X1.2T;BL
M02 MOTOR; AC ELEVATION;220V;80M M;225;10PIN;J
M03 MCB;2.0-2.75HP/220V;HAPA;0D0104;0.5W
M05 MOTOR FIX NG PLATE;MM384 -DARK SILVER;
M06 SCREW;SH; 5/16-18UNCX14L;HS;BP
M07 MOTO R CONTROL BOARD FI X PLATE; SPC;TM148
M08 NUT;NLK;M8X1.25P;BZN;
M09 WA SHE R;F LAT;Φ X8. 3XΦX1 6.0X 1.3T; BL Z N;R O
M10 SCREW;HEX HEAD;3/8-16UNC-47L-14L;BLAC
M12 NUT;NYLOCK;3/8''-16UNC;BLACK ANNODIZED;
M13 WASH ER;FLT;Φ10.5XΦ20.0X2.0T;BZN;
M14 SCREW;HH;3/8-16UNCX60L-18L ;HE;P-T
M17 FERRITE CORE
M23 NUT;HX;M6X1.0P;SS41;BZN;
M24 SCR EW;BUTTON HEA D;Φ4X10L;THREAD CUTT ING;
M25 WASHER;SPRING LOCK;ΦX8.2XΦX15.4X2.0T;BL
M28 SCREW;HH;M6X1.0PX25L;HE;
M30 WA SHE R;F LAT;Φ X8XΦ X16. 0X1.4 T;BL ZN; ROH S
M31 S CREW ;SH;M 8X1.2 5PX15L ;HS;C RMO;
M41 MOTOR ELASTOMER PAD;RU BBER;TM16
N43 SAFETY KEY SET;SEMI-ASSY;TM637
P03 WIRE;MCB PWR;550L;16AWG;BLACK;LOCKING
P04 POWER SWITCH;DOUBLE POLE;W/O LIGHT;125V/
P05 OVERCURR ENT BREAKER;10A;250V;TM18
NO. DESCRIPTION
P06 CONSO LE WIRE;BELOW;2150MM;CKM254301-
P08 WIRE;BS CON;BLACK;250LOCK2 60L;
P09 PWR SOCKET SET;CE;100,1250,80;TM283-P09A
P11 SF CONNECTI NG WIRE
P13 SCREW;FH;M3X0.5PX10L;PH;ZN;
P16 EXTERNAL PWR;IN;1.5MM;2M;
P16 EXTERNAL PWR;NEW ZEALAND;1.5MM;2M;
P16 EXTERNAL PWR;EUROPE;1.5MM;2M;
P16 EXTERNAL PWR;CHINA;1.5MM;2M
P16 EXTERNAL PWR;HK/KW/GB;1.5MM;2M;
P16 EXTERNAL PWR;US/CA/TH;16AWG;2M
P16 EXTERNAL PWR;ARGENTINA;1.5MM;2M;
P16 EXTERNAL PWR;SOUTH AFRICA;1.5MM;
P16 EXTERNAL PWR;SWEDEN;2M;1.5MM
P16 EXTERNAL PWR;BR;LENGTH:2M;1.5MM2
P16 EXTERNAL PWR;1.5MM2;2M;THAILAND;
P16 EXTERNAL PWR;TAIWAN;2.0MM2;2M;MEET T
P16 EXTERNAL PWR;KOREA;1.5MM2;2M;KC CERT
P16 EXTERNAL PWR WI RE SET;ISRAEL;1.5MM ;2
P16 WIRE;EXTERNAL PWR;SET;CHILE USED;JIS2 U
P17 SCREW;BH;M5X25L;CT;PH;NKL;
P18 WASHER;TOOTH;Φ5.3XΦ10.0X0.6T;BAN;
P19 NUT;HX;M5X0.8P;SS41;NKL;
P20 FILTER;10A;250V;DNF055-H -10A;ROHS
P21 POWE SWITCH FIX BASE;MM 384-DARK S ILV
P22 IND UCTANCE;6MH,200,200;TM27
3534
NO. DESCRIPTION
P25 WIRE;MCB PWR;550L;16AWG;WHITE;LOCKING
P29 SCRE W;BH;M5X12L;PH;BZN;
Q01 MOTOR COVER-EXREAWORK;SCREEN PRINT;TM
Q02 COVER;MOTOR;D;ABS;TM285
Q03 RAIL;ACCENT;PVC;BL/BLACK C;
Q04 COVER;FR AME;D;
Q06 END CAP;LEFT;ABS/PA757;TM480;
Q07 END CAP;RI GHT;ABS/PA757;TM480;
Q13 CLIP;STANDARD;WUSN-4039;
Q14 FIXING BLOCK;SIDE RAIL;STRONG-NYLON;T
Q15 SCREW;FH;#P5X15L;SM;PH;
Q20 SCREW;B H;ΦX4X15L;TC;PH;BED;POT;G8.8;
Q23 SCREW;TRH;Φ4X10L;SM;PH;BZN;POT
Q25 SCREW;BH;M 4X0.7PX8L;CT;PH;BZN;
Q34 COVE R LAYERING;D;PVC* *DISC NOT STOCKING
R02 TREADMILL BELT;500X3020X2.2T;NA;PAHS
R03 BELT;POLY-V;533J8;HUTCHINSON
R04 SCR EW;SH;M8X1.25PX90L ;HS;ZN;
R05 NUT;NLK;M8X1.25P;BZN;
R08 SCR EW;SH;M8X1.25PX30L; HS;BZN;
R09 SCR EW;SH;M8X1.25PX55L;H S;BAN;
R10 MAGN ET; 10 X3T
R12 WASH ER; FLAT; ΦX8 .3XΦ X16. 0X1.3 T;BL ZN; RO
Z01 SCREW;BH;M8X1.25PX20L;HS;BZN;BP
Z02 WASHER;ARC;Φ8.2XΦ16.0X1.0T;65MN;BZN
Z03 SCREW;FH;M8X1.25PX60L-20L;HS;BAN;BP;P
NO. DESCRIPTION
Z04 SCREW;BH;M4X0.7PX30L;PH;BAN;
Z05 SCREW;BH;M8X1.25PX20L;HS;BZN;BP
Z06 WASHER;FLT;Φ8.4XΦ15.5X1.6T;BZN;
Z07 WASHER;ARC;Φ8.2XΦ16.0X1.0T;65MN;BZN
Z08 WASHER;SPRING LOCK;ΦX8.2XΦX15.4X2.0T;BL
M01 DR IVER MOTOR;DC;GR EEN;2.5HP;180V;
M04 CASTING;MOTOR FLYWHEEL;FC20;?155,?35
M17 FERRITE CORE
M47 ECODE SET;SEMI-ASSY;2.5HP;
AN1 CONSOLE BASE FRAME SET;PAINTING;BLACK
C07 FOA M;ARM REST;EVA FOAM;TM477;
N01 COVER;CONSOLE;U;PAINTING;DARK SILVER;TM
N02 COV ER;CONSOLE;DOWN;A BS/PA757;BL/BLACK C;
N03 OVERLAY;PAINTING;DARK SILVER;TM477;
N08 FIXI NG BRACKET;NYLON 6 6;WHITE;1202 KSS
N13 COVER1;QUICK KEY;ABS/PA757;TM477
N19 KETTLE RACK;LEFT;ABS/PA757;TM477;
N20 KETTLE RACK;RIGHT;ABS/PA757;TM477;
N38 WIRE;GRIP PULSE;250+Φ6 ;500;TM219;TM2
N42 S CREW;BH;Φ4X8L;SM;PH;YZN;POT
N44 SCREW;BH;Φ4X12L;SM;PH;BZN;POT
N45 SCREW;BH;Φ3X8L;TC;PH;FLT
N60 (UP)CONTROL PANEL;HDPC;S1.007;PARAGON
N61 MEMBRANE KEYPAD;HANDBAR KEY;PARAGON 5-
N62 MEMBRANE KEYPAD;MEMBRANE;U;PARAGON 5-C;T
N63 OVERLAY;UP;ENG/GER;PARAGON 5 -C;
NO. DESCRIPTION
N64 OVERLAY;DOWN;ENG/GER;PARAGON 5 -C;INCLUD
N65 QUI CK KEY CON WIRE;L EFT;GREEN;950MM;
N66 QUICK KEY CON WIRE;RIGHT;YELLOW2;950M
N69 WIRELESS RECEIVER SET;130;XHS-3Y(RED)+
N70 SA FE SWITCH;RED;220L;(XHS2.5-2P);MAC
N71 MEMBRANE KEYPAD;SPEED;PARAGON5-C;ENG/G
N90 ADSORPTI VE PLATE;ZINC 15*25;TM257;TM25
P07 WIRE;PCB CONNECTION;650L(CKM254301-8P+SM
Q05 CAP;ARM REST;PP;BL/BLACK C
V63 LOGO LABEL;Φ30;AL;
3736
PARAGON 7S EXPLODED VIEW
NO. DESCRIPTION
1 MOTOR SET;MOTOR;TM482;
2 CONSOLE SET;CONSOLE;TM483;
AB1 FRAME SET-EXREAWORK;SCREEN PRINT;TM48
AH1 ELEVATION SUPT RACK SET;PAINTING;MM384
AK1 BASE FRAME SET;PAINTING;MM384;TM480-2
AQ1 SHIELD SET;CONSOLE MAST;LEFT DOWN;TM480
AQ2 SHIELD SET;CONSOLE MAST;RIGHT DOWN;TM48
AR1 RO LLER SET;FRONT;TEXTUR E;TM136
AR2 ROLLER S ET;REAR;Φ46;TM59
B29 AIR STICK;SLOW-DROP;400N;JOURNEY350MM;
B30 EL ASTOMER;RUNN ING DECK;Φ30X37X 26;TM41
B31 FINISHED TREADMILL DECK;600X1340X18T;SI
B32 ELASTOMER
B34 BELT GUIDE
B35 SCR EW;BH;ΦX5X12L;TC;PH;BED;POT;
B36 SC REW;FH;M8X1.25PX30L ;HS;
B37 NUT;NLK;M8X1.25P;BZN;
B38 SI DE RAIL FIXIN G PLATE;MM384- DARK SI
B39 SCRE W;TRH;ΦX4X15L;TC;PH;BED;POT;
B41 SCREW;BH;M8X1.25PX30L;HS;BAN;
B45 WASHER;FL AT;ΦX8.2XΦX15.0X1.2T;BED;ROHS
B46 EL ASTOMER BLACK 9 0
B49 STOPPER;PAINTING;BLACK2;TM480;
B66 SLEEV E;Φ22.2X1.0TX22L;TM27
C01 CONSOLE MAST-EXTRAWORK;LEFT;SCREEN PRIN
C02 CONSOLE MAST-EXTRAWORK;RIGHT;SCREEN PRI
NO. DESCRIPTION
H10 WASH ER;F LT;Φ1 0.5 XΦ18 .0X 2.6 T;
H30 SCREW;M8X1.25PX26L-10L;20CR;BAN;SP
H31 WASHER;FLT;Φ10.5XΦ20.0X1.0T;TFN;
H32 WASHER;FL AT;ΦX10.2XΦX20.0X1.0T;BL ZN;R
H33 WASHER;FL AT;Φ10.5XΦ20.0X2.0T;ZINC;
H36 SNA P RING;EXTERNAL C-SHAPED;S-10;BLACK
H37 RU BBER STOPPER;AC003;TM16
K11 CONNECT PLATE;MM384-DARK SILVER;TM48
K14 SCREW;M8X1.25PX12L-6L;BZN;P-T
K15 SPRING;EXT;Φ2.0XΦ16.0X50.0LX12N;
K17 SCREW;BH;M10X1.5PX40L;HS;BP
K19 SCREW;FH;M8X1.25PX4 5L-15L;HS;BZN;P-T
K20 SCR EW;BH;M8X15L;HS;BZN;BP;G8.8;
K23 SC REW;FH;M4XX40L;PH;BED;
K25 BRAKE LOCATION SET;TM332
K27 FOOT PAD;ADJUST;RUBBER;W3/8-16UNC;FMW38A
K28 RVN;ALS7-616 -150(0.02 -0.15);YZN;
K30 WASHER;FLT;Φ8.5XΦ19.0X2.0T;BZN;
K31 HOOK BASE;PAINTING;MM384;TM480;
K35 ADJUSTABLE FOOT PAD NUT
L01 FRONT CARRIAGE RO LLER; NYLON PA6;Φ46XΦ10
L02 WHEEL MOBILE FRA ME BASE
L05 WHEEL;NYLON;Φ74;TM27
L06 TRANSPORT WHEEL
L07 WASHER;FLT;Φ10.5XΦ20.0X2.0T;BZN;
L09 SCREW;HEX;M6X1.0PX25L;
3938
NO. DESCRIPTION
L17 LOCATION HOOK;PAINTING;MM384;TM480;
L21 SCRE W;SH; M6X1.0 PX10L; HS;B ZN;
L25 WASHER;SPRING LOCK;ΦX6.1XΦX10.0X1.2T;BL
M02 MOTOR; AC ELEVATION;220V;80M M;225;10PIN;J
M03 MCB;2.0-2.75HP/220V;HAPA;0D0104;0.5W
M05 MOTOR FIX NG PLATE;MM384 -DARK SILVER;
M06 SCREW;SH; 5/16-18UNCX14L;HS;BP
M07 MOTO R CONTROL BOARD FI X PLATE; SPC;TM148
M08 NUT;NLK;M8X1.25P;BZN;
M09 WA SHE R;F LAT;Φ X8. 3XΦX1 6.0X 1.3T; BL Z N;R O
M10 SCREW;HEX HEAD;3/8-16UNC-47L-14L;BLAC
M12 NUT;NYLOCK;3/8''-16UNC;BLACK ANNODIZED;
M13 WASH ER;FLT;Φ10.5XΦ20.0X2.0T;BZN;
M14 SCREW;HH;3/8-16UNCX60L-18L ;HE;P-T
M17 FERRITE CORE
M23 NUT;HX;M6X1.0P;SS41;BZN;
M24 SCR EW;BUTTON HEA D;Φ4X10L;THREAD CUTT ING;
M25 WASHER;SPRING LOCK;ΦX8.2XΦX15.4X2.0T;BL
M28 SCREW;HH;M6X1.0PX25L;HE;
M30 WA SHE R;F LAT;Φ X8XΦ X16. 0X1.4 T;BL ZN; ROH S
M31 S CREW ;SH;M 8X1.2 5PX15L ;HS;C RMO;
M41 MOTOR ELASTOMER PAD;RU BBER;TM16
N43 SAFETY KEY SET;SEMI-ASSY;TM637
P03 WIRE;MCB PWR;550L;16AWG;BLACK;LOCKING
P04 POWER SWITCH;DOUBLE POLE;W/O LIGHT;125V/
P05 OVERCURR ENT BREAKER;10A;250V;TM18
NO. DESCRIPTION
P25 WIRE;MCB PWR;550L;16AWG;WHITE;LOCKING
P29 SCRE W;BH;M5X12L;PH;BZN;
Q01 MOTOR COVER-EXREAWORK;SCREEN PRINT;TM
Q02 COVER;MOTOR;D;ABS;TM285
Q03 RAIL;ACCENT;PVC;BL/BLACK C;
Q04 COVER;FR AME;D;
Q06 END CAP;LEFT;ABS/PA757;TM480;
Q07 END CAP;RI GHT;ABS/PA757;TM480;
Q13 CLIP;STANDARD;WUSN-4039;
Q14 FIXING BLOCK;SIDE RAIL;STRONG-NYLON;T
Q15 SCREW;FH;#P5X15L;SM;PH;
Q20 SCREW;B H;ΦX4X15L;TC;PH;BED;POT;G8.8;
Q23 SCREW;TRH;Φ4X10L;SM;PH;BZN;POT
Q25 SCREW;BH;M 4X0.7PX8L;CT;PH;BZN;
Q34 COVE R LAYERING;D;PVC* *DISC NOT STOCKING
R02 TREADMILL BELT;500X3020X2.2T;NA;PAHS
R03 BELT;POLY-V;533J8;HUTCHINSON
R04 SCR EW;SH;M8X1.25PX90L ;HS;ZN;
R05 NUT;NLK;M8X1.25P;BZN;
R08 SCR EW;SH;M8X1.25PX30L; HS;BZN;
R09 SCR EW;SH;M8X1.25PX55L;H S;BAN;
R10 MAGN ET; 10 X3T
R12 WASH ER; FLAT; ΦX8 .3XΦ X16. 0X1.3 T;BL ZN; RO
Z01 SCREW;BH;M8X1.25PX20L;HS;BZN;BP
Z02 WASHER;ARC;Φ8.2XΦ16.0X1.0T;65MN;BZN
Z03 SCREW;FH;M8X1.25PX60L-20L;HS;BAN;BP;P
NO. DESCRIPTION
P06 CONSO LE WIRE;BELOW;2150MM;CKM254301-
P08 WIRE;BS CON;BLACK;250LOCK2 60L;
P09 PWR SOCKET SET;CE;100,1250,80;TM283-P09A
P11 SF CONNECTI NG WIRE
P13 SCREW;FH;M3X0.5PX10L;PH;ZN;
P16 EXTERNAL PWR;IN;1.5MM;2M;
P16 EXTERNAL PWR;NEW ZEALAND;1.5MM;2M;
P16 EXTERNAL PWR;EUROPE;1.5MM;2M;
P16 EXTERNAL PWR;CHINA;1.5MM;2M
P16 EXTERNAL PWR;HK/KW/GB;1.5MM;2M;
P16 EXTERNAL PWR;US/CA/TH;16AWG;2M
P16 EXTERNAL PWR;ARGENTINA;1.5MM;2M;
P16 EXTERNAL PWR;SOUTH AFRICA;1.5MM;
P16 EXTERNAL PWR;SWEDEN;2M;1.5MM
P16 EXTERNAL PWR;BR;LENGTH:2M;1.5MM2
P16 EXTERNAL PWR;1.5MM2;2M;THAILAND;
P16 EXTERNAL PWR;TAIWAN;2.0MM2;2M;MEET T
P16 EXTERNAL PWR;KOREA;1.5MM2;2M;KC CERT
P16 EXTERNAL PWR WI RE SET;ISRAEL;1.5MM ;2
P16 WIRE;EXTERNAL PWR;SET;CHILE USED;JIS2 U
P17 SCREW;BH;M5X25L;CT;PH;NKL;
P18 WASHER;TOOTH;Φ5.3XΦ10.0X0.6T;BAN;
P19 NUT;HX;M5X0.8P;SS41;NKL;
P20 FILTER;10A;250V;DNF055-H -10A;ROHS
P21 POWE SWITCH FIX BASE;MM 384-DARK S ILV
P22 IND UCTANCE;6MH,200,200;TM27
NO. DESCRIPTION
Z04 SCREW;BH;M4X0.7PX30L;PH;BAN;
Z05 SCREW;BH;M8X1.25PX20L;HS;BZN;BP
Z06 WASHER;FLT;Φ8.4XΦ15.5X1.6T;BZN;
Z07 WASHER;ARC;Φ8.2XΦ16.0X1.0T;65MN;BZN
Z08 WASHER;SPRING LOCK;ΦX8.2XΦX15.4X2.0T;BL
M01 DR IVER MOTOR;DC;GR EEN;2.5HP;180V;
M04 CASTING;MOTOR FLYWHEEL;FC20;?155,?35
M17 FERRITE CORE
M47 ECODE SET;SEMI-ASSY;2.5HP;
AN1 CONSOLE BASE FRAME SET;PAINTING;BLACK
C07 FOA M;ARM REST;EVA FOAM;TM477;
N01 COVER;CONSOLE;U;PAINTING;DARK SILVER;TM
N02 COV ER;CONSOLE;DOWN;A BS/PA757;BL/BLACK C;
N03 OVERLAY;PAINTING;DARK SILVER;TM478;
N04 SHIM;RE ADING RACK;FROTH;
N08 FIXI NG BRACKET;NYLON 6 6;WHITE;1202 KSS
N13 COVER1;QUICK KEY;ABS/PA757;TM477
N19 KETTLE RACK;LEFT;ABS/PA757;TM477;
N20 KETTLE RACK;RIGHT;ABS/PA757;TM477;
N38 WIRE;GRIP PULSE;250+Φ6 ;500;TM219;TM2
N42 S CREW;BH;Φ4X8L;SM;PH;YZN;POT
N44 SCREW;BH;Φ4X12L;SM;PH;BZN;POT
N45 SCREW;BH;Φ3X8L;TC;PH;FLT
N60 (UP)CONTROL PANEL;HDPC;S1.006;PARAGON
P21 POWE SWITCH FIX BASE;MM 384-DARK S ILV
P22 IND UCTANCE;6MH,200,200;TM27
4140
PARAGON 7E EXPLODED VIEW
NO. DESCRIPTION
N61 KEY;HANDGRIP SHRAPNEL KEYPAD;PARAGON 7
N62 OVERLAY;UP;ENG/GER;PARAGON 7-C;TM478;
N63 KEY;U;SHRAPNEL KEY;TM478;PARAGON 7&8-C
N64 OVERLAY;DOWN;ENG/GER;PARAGON 8-C;INCLUDE
N65 QUI CK KEY CON WIRE;L EFT;GREEN;950MM;
N66 QUICK KEY CON WIRE;RIGHT;YELLOW2;950M
N68 KE Y;PASSPO RT KEY PAD;PAR AGON 7&8 -C;SH RA
N69 WIRELESS RECEIVER SET;130;XHS-3Y(RED)+
N70 SA FE SWITCH;RED;220L;(XHS2.5-2P);MAC
N71 KEY;SPEED;HANDGRIP SHRAPNEL KEYPAD;PARA
N90 ADSORPTI VE PLATE;ZINC 15*25;TM257;TM25
P07 WIRE;PCB CONNECTION;650L(CKM254301-8P+SM
Q05 CAP;ARM REST;PP;BL/BLACK C
V63 LOGO LABEL;Φ30;AL;
4342
NO. DESCRIPTION
1 MOTOR SET;TM484;
2 CONSOLE SET;TM484;
3 SIDE RAIL SET;TM484;
AB1 FRAME SET;PAINTING;MM379;TM481;
AH1 ELEVATION SUPT RACK SET;PAINTING;MM379
AK1 BASE FRAME SET;PAINTING;MM379;TM481;
AQ1 SHIELD SET;CONSOLE MAST;LEFT DOWN;TM481
AQ2 SHIELD SET;CONSOLE MAST;RIGHT DOWN;TM48
AR1 RO LLER SET;FRONT;TEXTUR E;TM136
AR2 ROLLER S ET;REAR;Φ46;TM59
B29 AIR STICK;SLOW-DROP;400N;JOURNEY350MM;
B30 EL ASTOMER;RUNN ING DECK;Φ30X37X 26;TM41
B31 FINISHED TREADMILL DECK;600X1340X18T;SI
B32 ELASTOMER
B34 BELT GUIDE
B35 SCR EW;BH;ΦX5X12L;TC;PH;BED;POT;
B36 SC REW;FH;M8X1.25PX30L ;HS;
B37 NUT;NLK;M8X1.25P;BZN;
B38 SIDE RAIL FIXING PLATE;MM379;TM481;
B39 SCRE W;TRH;ΦX4X15L;TC;PH;BED;POT;
B41 SCREW;BH;M8X1.25PX30L;HS;BAN;
B45 WASHER;FL AT;ΦX8.2XΦX15.0X1.2T;BED;ROHS
B46 EL ASTOMER BLACK 9 0
B49 STOPPER;PAINTING;BLACK2;TM480;
B66 SLEEV E;Φ22.2X1.0TX22L;TM27
C01 CONSOLE MAST-EXTRAWORK;LEFT;SCREEN PRIN
NO. DESCRIPTION
L09 SCREW;HEX;M6X1.0PX25L;
L17 LOCATION HOOK;PAINTING;MM379;TM481;
L21 SCRE W;SH; M6X1.0 PX10L; HS;B ZN;
L25 WASHER;SPRING LOCK;ΦX6.1XΦX10.0X1.2T;BL
M02 MOTOR; AC ELEVATION;220V;80M M;225;10PIN;J
M03 MCB;2.0-2.75HP/220V;HAPA;0D0104;0.5W
M05 MOTOR FIX NG PLATE;MM379;TM481;
M06 SCREW;SH; 5/16-18UNCX14L;HS;BP
M07 MOTO R CONTROL BOARD FI X PLATE; SPC;TM148
M08 NUT;NLK;M8X1.25P;BZN;
M09 WA SHE R;F LAT;Φ X8. 3XΦX1 6.0X 1.3T; BL Z N;R O
M10 SCREW;HEX HEAD;3/8-16UNC-47L-14L;BLAC
M12 NUT;NYLOCK;3/8''-16UNC;BLACK ANNODIZED;
M13 WASH ER;FLT;Φ10.5XΦ20.0X2.0T;BZN;
M14 SCREW;HH;3/8-16UNCX60L-18L ;HE;P-T
M17 FERRITE CORE
M23 NUT;HX;M6X1.0P;SS41;BZN;
M24 SCR EW;BUTTON HEA D;Φ4X10L;THREAD CUTT ING;
M25 WASHER;SPRING LOCK;ΦX8.2XΦX15.4X2.0T;BL
M28 SCREW;HH;M6X1.0PX25L;HE;
M30 WA SHE R;F LAT;Φ X8XΦ X16. 0X1.4 T;BL ZN; ROH S
M31 S CREW ;SH;M 8X1.2 5PX15L ;HS;C RMO;
M41 MOTOR ELASTOMER PAD;RU BBER;TM16
N43 SAFETY KEY SET;SEMI-ASSY;TM637
P03 WIRE;MCB PWR;550L;16AWG;BLACK;LOCKING
P04 POWER SWITCH;DOUBLE POLE;W/O LIGHT;125V/
NO. DESCRIPTION
C02 CONSOLE MAST-EXTRAWORK;RIGHT;SCREEN PRI
H10 WASH ER;F LT;Φ1 0.5 XΦ18 .0X 2.6 T;
H30 SCREW;M8X1.25PX26L-10L;20CR;BAN;SP
H31 WASHER;FLT;Φ10.5XΦ20.0X1.0T;TFN;
H32 WASHER;FL AT;ΦX10.2XΦX20.0X1.0T;BL ZN;R
H33 WASHER;FL AT;Φ10.5XΦ20.0X2.0T;ZINC;
H36 SNA P RING;EXTERNAL C-SHAPED;S-10;BLACK
H37 RU BBER STOPPER;AC003;TM16
K11 CONNECT PLATE;MM37 9;TM481;
K14 SCREW;M8X1.25PX12L-6L;BZN;P-T
K15 SPRING;EXT;Φ2.0XΦ16.0X50.0LX12N;
K17 SCREW;BH;M10X1.5PX40L;HS;BP
K19 SCREW;FH;M8X1.25PX4 5L-15L;HS;BZN;P-T
K20 SCR EW;BH;M8X15L;HS;BZN;BP;G8.8;
K23 SC REW;FH;M4XX40L;PH;BED;
K25 BRAKE LOCATION SET;TM332
K27 FOOT PAD;ADJUST;RUBBER;W3/8-16UNC;FMW38A
K28 RVN;ALS7-616 -150(0.02 -0.15);YZN;
K30 WASHER;FLT;Φ8.5XΦ19.0X2.0T;BZN;
K31 HOOK BASE;PAINTING;MM379;TM481;
K35 ADJUSTABLE FOOT PAD NUT
L01 FRONT CARRIAGE RO LLER; NYLON PA6;Φ46XΦ10
L02 WHEEL MOBILE FRA ME BASE
L05 WHEEL;NYLON;Φ74;TM27
L06 TRANSPORT WHEEL
L07 WASHER;FLT;Φ10.5XΦ20.0X2.0T;BZN;
NO. DESCRIPTION
P05 OVERCURR ENT BREAKER;10A;250V;TM18
P06 CONSO LE WIRE;BELOW;2150MM;CKM254301-
P08 WIRE;BS CON;BLACK;250LOCK2 60L;
P09 PWR SOCKET SET;CE;100,1250,80;TM283-P09A
P11 SF CONNECTI NG WIRE
P13 SCREW;FH;M3X0.5PX10L;PH;ZN;
P16 EXTERNAL PWR;IN;1.5MM;2M;
P16 EXTERNAL PWR;NEW ZEALAND;1.5MM;2M;
P16 EXTERNAL PWR;EUROPE;1.5MM;2M;
P16 EXTERNAL PWR;CHINA;1.5MM;2M
P16 EXTERNAL PWR;HK/KW/GB;1.5MM;2M;
P16 EXTERNAL PWR;US/CA/TH;16AWG;2M
P16 EXTERNAL PWR;ARGENTINA;1.5MM;2M;
P16 EXTERNAL PWR;SOUTH AFRICA;1.5MM;
P16 EXTERNAL PWR;SWEDEN;2M;1.5MM
P16 EXTERNAL PWR;BR;LENGTH:2M;1.5MM2
P16 EXTERNAL PWR;1.5MM2;2M;THAILAND;
P16 EXTERNAL PWR;TAIWAN;2.0MM2;2M;MEET T
P16 EXTERNAL PWR;KOREA;1.5MM2;2M;KC CERT
P16 EXTERNAL PWR WI RE SET;ISRAEL;1.5MM ;2
P16 WIRE;EXTERNAL PWR;SET;CHILE USED;JIS2 U
P17 SCREW;BH;M5X25L;CT;PH;NKL;
P18 WASHER;TOOTH;Φ5.3XΦ10.0X0.6T;BAN;
P19 NUT;HX;M5X0.8P;SS41;NKL;
P20 FILTER;10A;250V;DNF055-H -10A;ROHS
P21 POWE SWITCH FIX BASE;MM379;TM481;
4544
NO. DESCRIPTION
P22 IND UCTANCE;6MH,200,200;TM27
P25 WIRE;MCB PWR;550L;16AWG;WHITE;LOCKING
P29 SCRE W;BH;M5X12L;PH;BZN;
Q01 MOTOR COVER-EXREAWORK;SCREEN PRINT;T
Q02 COVER;MOTOR;D;ABS;TM285
Q04 COVER;FR AME;D;
Q06 END CAP;LEFT;ABS/PA757;TM480;
Q07 END CAP;RI GHT;ABS/PA757;TM480;
Q13 CLIP;STANDARD;WUSN-4039;
Q14 FIXING BLOCK;SIDE RAIL;STRONG-NYLON;T
Q15 SCREW;FH;#P5X15L;SM;PH;
Q20 SCREW;BH;Φ 4X15L;SM;PH;CHM;POT
Q23 SCREW;TRH;Φ4X10L;SM;PH;BZN;POT
Q25 SCREW;BH;M 4X0.7PX8L;CT;PH;BZN;
Q28 SCRE W;BH;ΦX4X15L;TC;PH;BED;POT;G8.8;
Q34 COVE R LAYERING;D;PVC* *DISC NOT STOCKING
R02 TREADM ILL BELT;500X3020X3.1T;NA;
R03 BELT;POLY-V;533J8;HUTCHINSON
R04 SCR EW;SH;M8X1.25PX90L ;HS;ZN;
R05 NUT;NLK;M8X1.25P;BZN;
R08 SCR EW;SH;M8X1.25PX30L; HS;BZN;
R09 SCR EW;SH;M8X1.25PX55L;H S;BAN;
R10 MAGN ET; 10 X3T
R12 WASH ER; FLAT; ΦX8 .3XΦ X16. 0X1.3 T;BL ZN; RO
V05 LOGO LABEL;AL;TM481;
Z01 SCREW;BH;M8X1.25PX20L;HS;BZN;BP
NO. DESCRIPTION
N45 SCREW;BH;Φ3X8L;TC;PH;FLT
N60 (UP)CONTROL PANEL;HDPC;S1.006;PARAGON
N61 KEY;HANDGRIP SHRAPNEL KEYPAD;PARAGON 7
N62 OVERLAY;UP;ENG/GER;PARAGON 7-C;TM478;
N63 KEY;U;SHRAPNEL KEY;TM478;PARAGON 7&8-C
N64 OVERLAY;DOWN;ENG/GER;PARAGON 8-C;INCLUDE
N65 QUI CK KEY CON WIRE;L EFT;GREEN;950MM;
N66 QUICK KEY CON WIRE;RIGHT;YELLOW2;950M
N68 KE Y;PASSPO RT KEY PAD;PAR AGON 7&8 -C;SH RA
N69 WIRELESS RECEIVER SET;130;XHS-3Y(RED)+
N70 SA FE SWITCH;RED;220L;(XHS2.5-2P);MAC
N71 KEY;SPEED;HANDGRIP SHRAPNEL KEYPAD;PARA
N90 ADSORPTI VE PLATE;ZINC 15*25;TM257;TM25
P07 WIRE;PCB CONNECTION;650L(CKM254301-8P+SM
Q05 CAP;ARM REST;PP;BL/BLACK C
V63 LOGO LABEL;Φ30;AL;
NO. DESCRIPTION
Z02 WASHER;ARC;Φ8.2XΦ16.0X1.0T;65MN;BZN
Z03 SCREW;FH;M8X1.25PX60L-20L;HS;BAN;BP;P
Z04 SCREW;BUTTON HEA D;M4X0.7PX30L;MAC HINE TH
Z05 SCREW;BH;M8X1.25PX20L ;HS;CHM;
Z06 WASHER;FLAT;Φ8.2XΦ15.0X1.2T;CHROME;ROH
Z07 WASHER;ARC;Φ8.4XΦ17.0X1.0T;CHM;
Z08 WASHER;SPRING LOCK;ΦX 8. 2XΦX15.4X2.0T;C
M01 DR IVER MOTOR;DC;BL ACK;2.75HP;180V;38 00
M04 CASTING;MOTOR FLYWHEEL;FC20;?155,?35
M17 FERRITE CORE
M47 ECODE SET;SEMI-ASSY;2.5HP;
Q03 RAIL;ACCENT;PVC;BL/BLACK C;
Q18 D ECORATED PIECE;SIDE RAIL;6X1324L;TM
AN1 CONSOLE BASE FRAME SET;PAINTING;BLACK
C07 FOA M;ARM REST;EVA FOAM;TM477;
N01 COVER;CONSOLE;U;PAINTING;DARK SILVER;TM
N02 COV ER;CONSOLE;DOWN;A BS/PA757;BL/BLACK C;
N03 OVERLAY;PAINTING;DARK SILVER;TM478;
N04 SHIM;RE ADING RACK;FROTH;
N08 FIXI NG BRACKET;NYLON 6 6;WHITE;1202 KSS
N13 COVER1;QUICK KEY;ABS/PA757;TM477
N19 KETTLE RACK;LEFT;ABS/PA757;TM477;
N20 KETTLE RACK;RIGHT;ABS/PA757;TM477;
N38 WIRE;GRIP PULSE;250+Φ6 ;500;TM219;TM2
N42 S CREW;BH;Φ4X8L;SM;PH;YZN;POT
N44 SCREW;BH;Φ4X12L;SM;PH;BZN;POT
4746
PARAGON 8E EXPLODED VIEW
NO. DESCRIPTION
1 MOTOR SET;TM484;
2 CONSOLE SET;TM485;
3 SIDE RAIL SET;TM484;
AB1 FRAME SET;PAINTING;MM379;TM481;
AH1 ELEVATION SUPT RACK SET;PAINTING;MM379
AK1 BASE FRAME SET;PAINTING;MM379;TM481;
AQ1 SHIELD SET;CONSOLE MAST;LEFT DOWN;TM481
AQ2 SHIELD SET;CONSOLE MAST;RIGHT DOWN;TM48
AR1 RO LLER SET;FRONT;TEXTUR E;TM136
AR2 ROLLER S ET;REAR;Φ46;TM59
B29 AIR STICK;SLOW-DROP;400N;JOURNEY350MM;
B30 EL ASTOMER;RUNN ING DECK;Φ30X37X 26;TM41
B31 FINISHED TREADMILL DECK;600X1340X18T;SI
B32 ELASTOMER
B34 BELT GUIDE
B35 SCR EW;BH;ΦX5X12L;TC;PH;BED;POT;
B36 SC REW;FH;M8X1.25PX30L ;HS;
B37 NUT;NLK;M8X1.25P;BZN;
B38 SIDE RAIL FIXING PLATE;MM379;TM481;
B39 SCRE W;TRH;ΦX4X15L;TC;PH;BED;POT;
B41 SCREW;BH;M8X1.25PX30L;HS;BAN;
B45 WASHER;FL AT;ΦX8.2XΦX15.0X1.2T;BED;ROHS
B46 EL ASTOMER BLACK 9 0
B49 STOPPER;PAINTING;BLACK2;TM480;
B66 SLEEV E;Φ22.2X1.0TX22L;TM27
H10 WASH ER;F LT;Φ1 0.5 XΦ18 .0X 2.6 T;
NO. DESCRIPTION
H30 SCREW;M8X1.25PX26L-10L;20CR;BAN;SP
H31 WASHER;FLT;Φ10.5XΦ20.0X1.0T;TFN;
H32 WASHER;FL AT;ΦX10.2XΦX20.0X1.0T;BL ZN;R
H33 WASHER;FL AT;Φ10.5XΦ20.0X2.0T;ZINC;
H36 SNA P RING;EXTERNAL C-SHAPED;S-10;BLACK
H37 RU BBER STOPPER;AC003;TM16
K11 CONNECT PLATE;MM37 9;TM481;
K14 SCREW;M8X1.25PX12L-6L;BZN;P-T
K15 SPRING;EXT;Φ2.0XΦ16.0X50.0LX12N;
K17 SCREW;BH;M10X1.5PX40L;HS;BP
K19 SCREW;FH;M8X1.25PX4 5L-15L;HS;BZN;P-T
K20 SCR EW;BH;M8X15L;HS;BZN;BP;G8.8;
K23 SC REW;FH;M4XX40L;PH;BED;
K25 BRAKE LOCATION SET;TM332
K27 FOOT PAD;ADJUST;RUBBER;W3/8-16UNC;FMW38A
K28 RVN;ALS7-616 -150(0.02 -0.15);YZN;
K30 WASHER;FLT;Φ8.5XΦ19.0X2.0T;BZN;
K31 HOOK BASE;PAINTING;MM379;TM481;
K35 ADJUSTABLE FOOT PAD NUT
L01 FRONT CARRIAGE RO LLER; NYLON PA6;Φ46XΦ10
L02 WHEEL MOBILE FRA ME BASE
L05 WHEEL;NYLON;Φ74;TM27
L06 TRANSPORT WHEEL
L07 WASHER;FLT;Φ10.5XΦ20.0X2.0T;BZN;
L09 SCREW;HEX;M6X1.0PX25L;
L17 LOCATION HOOK;PAINTING;MM379;TM481;
4948
NO. DESCRIPTION
L21 SCRE W;SH; M6X1.0 PX10L; HS;B ZN;
L25 WASHER;SPRING LOCK;ΦX6.1XΦX10.0X1.2T;BL
M02 MOTOR; AC ELEVATION;220V;80M M;225;10PIN;J
M03 MCB;2.0-2.75HP/220V;HAPA;0D0104;0.5W
M05 MOTOR FIX NG PLATE;MM379;TM481;
M06 SCREW;SH; 5/16-18UNCX14L;HS;BP
M07 MOTO R CONTROL BOARD FI X PLATE; SPC;TM148
M08 NUT;NLK;M8X1.25P;BZN;
M09 WA SHE R;F LAT;Φ X8. 3XΦX1 6.0X 1.3T; BL Z N;R O
M10 SCREW;HEX HEAD;3/8-16UNC-47L-14L;BLAC
M12 NUT;NYLOCK;3/8''-16UNC;BLACK ANNODIZED;
M13 WASH ER;FLT;Φ10.5XΦ20.0X2.0T;BZN;
M14 SCREW;HH;3/8-16UNCX60L-18L ;HE;P-T
M17 FERRITE CORE
M23 NUT;HX;M6X1.0P;SS41;BZN;
M24 SCR EW;BUTTON HEA D;Φ4X10L;THREAD CUTT ING;
M25 WASHER;SPRING LOCK;ΦX8.2XΦX15.4X2.0T;BL
M28 SCREW;HH;M6X1.0PX25L;HE;
M30 WA SHE R;F LAT;Φ X8XΦ X16. 0X1.4 T;BL ZN; ROH S
M31 S CREW ;SH;M 8X1.2 5PX15L ;HS;C RMO;
M41 MOTOR ELASTOMER PAD;RU BBER;TM16
N43 SAFETY KEY SET;SEMI-ASSY;TM637
P03 WIRE;MCB PWR;550L;16AWG;BLACK;LOCKING
P04 POWER SWITCH;DOUBLE POLE;W/O LIGHT;125V/
P05 OVERCURR ENT BREAKER;10A;250V;TM18
P06 CONSO LE WIRE;BELOW;2150MM;CKM254301
NO. DESCRIPTION
P08 WIRE;BS CON;BLACK;250LOCK2 60L;
P09 PWR SOCKET SET;CE;100,1250,80;TM283-P09A
P11 SF CONNECTI NG WIRE
P13 SCREW;FH;M3X0.5PX10L;PH;ZN;
P16 EXTERNAL PWR;IN;1.5MM;2M;
P16 EXTERNAL PWR;NEW ZEALAND;1.5MM;2M;
P16 EXTERNAL PWR;EUROPE;1.5MM;2M;
P16 EXTERNAL PWR;CHINA;1.5MM;2M
P16 EXTERNAL PWR;HK/KW/GB;1.5MM;2M;
P16 EXTERNAL PWR;US/CA/TH;16AWG;2M
P16 EXTERNAL PWR;ARGENTINA;1.5MM;2M;
P16 EXTERNAL PWR;SOUTH AFRICA;1.5MM;
P16 EXTERNAL PWR;SWEDEN;2M;1.5MM
P16 EXTERNAL PWR;BR;LENGTH:2M;1.5MM2
P16 EXTERNAL PWR;1.5MM2;2M;THAILAND;
P16 EXTERNAL PWR;TAIWAN;2.0MM2;2M;MEET T
P16 EXTERNAL PWR;KOREA;1.5MM2;2M;KC CERT
P16 EXTERNAL PWR WI RE SET;ISRAEL;1.5MM ;2
P16 WIRE;EXTERNAL PWR;SET;CHILE USED;JIS2 U
P17 SCREW;BH;M5X25L;CT;PH;NKL;
P18 WASHER;TOOTH;Φ5.3XΦ10.0X0.6T;BAN;
P19 NUT;HX;M5X0.8P;SS41;NKL;
P20 FILTER;10A;250V;DNF055-H -10A;ROHS
P21 POWE SWITCH FIX BASE;MM379;TM481;
P22 IND UCTANCE;6MH,200,200;TM27
P25 WIRE;MCB PWR;550L;16AWG;WHITE;LOCKING
NO. DESCRIPTION
P29 SCRE W;BH;M5X12L;PH;BZN;
Q01 MOTOR COVER-EXREAWORK;SCREEN PRINT;T
Q02 COVER;MOTOR;D;ABS;TM285
Q04 COVER;FR AME;D;
Q06 END CAP;LEFT;ABS/PA757;TM480;
Q07 END CAP;RI GHT;ABS/PA757;TM480;
Q13 CLIP;STANDARD;WUSN-4039;
Q14 FIXING BLOCK;SIDE RAIL;STRONG-NYLON;T
Q15 SCREW;FH;#P5X15L;SM;PH;
Q20 SCREW;BH;Φ 4X15L;SM;PH;CHM;POT
Q23 SCREW;TRH;Φ4X10L;SM;PH;BZN;POT
Q25 SCREW;BH;M 4X0.7PX8L;CT;PH;BZN;
Q28 SCRE W;BH;ΦX4X15L;TC;PH;BED;POT;G8.8;
Q34 COVE R LAYERING;D;PVC* *DISC NOT STOCKING
R02 TREADM ILL BELT;500X3020X3.1T;NA;
R03 BELT;POLY-V;533J8;HUTCHINSON
R04 SCR EW;SH;M8X1.25PX90L ;HS;ZN;
R05 NUT;NLK;M8X1.25P;BZN;
R08 SCR EW;SH;M8X1.25PX30L; HS;BZN;
R09 SCR EW;SH;M8X1.25PX55L;H S;BAN;
R10 MAGN ET; 10 X3T
R12 WASH ER; FLAT; ΦX8 .3XΦ X16. 0X1.3 T;BL ZN; RO
V05 LOGO LABEL;AL;TM481;
Z01 SCREW;BH;M8X1.25PX20L;HS;BZN;BP
Z02 WASHER;ARC;Φ8.2XΦ16.0X1.0T;65MN;BZN
Z03 SCREW;FH;M8X1.25PX60L-20L;HS;BAN;BP;P
NO. DESCRIPTION
Z04 SCREW;BUTTON HEA D;M4X0.7PX30L;MAC HINE TH
Z05 SCREW;BH;M8X1.25PX20L ;HS;CHM;
Z06 WASHER;FLAT;Φ8.2XΦ15.0X1.2T;CHROME;ROH
Z07 WASHER;ARC;Φ8.4XΦ17.0X1.0T;CHM;
Z08 WASHER;SPRING LOCK;ΦX 8. 2XΦX15.4X2.0T;C
M01 DR IVER MOTOR;DC;BL ACK;2.75HP;180V;38 00
M04 CASTING;MOTOR FLYWHEEL;FC20;?155,?35
M17 FERRITE CORE
M47 ECODE SET;SEMI-ASSY;2.5HP;
Q03 RAIL;ACCENT;PVC;BL/BLACK C;
Q18 D ECORATED PIECE;SIDE RAIL;6X1324L;TM
AN1 CONSOLE BASE FRAME SET;PAINTING;BLACK
C07 FOA M;ARM REST;EVA FOAM;TM477;
N01 COVER;CONSOLE;U;PAINTING;DARK SILVER;TM
N02 COV ER;CONSOLE;DOWN;A BS/PA757;BL/BLACK C;
N03 OVERLAY;CONSOLE;PAINTING;DARK SILVER;T
N04 SHIM;READING RACK;SILICA;
N08 FIXI NG BRACKET;NYLON 6 6;WHITE;1202 KSS
N13 COVER1;QUICK KEY;ABS/PA757;TM479
N19 KETTLE RACK;L;PAINTING;MM384-DARK SILV
N20 KETTLE RACK;R;PAINTING;MM384-DARK SILV
N25 COV ER;LOGO;ACRYLIC;
N27 INSIDE COVER;LOGO;ABS/PA757;
N28 SPRING;CMP;Φ18XΦ1.0X30LX5.0N;
N38 WIRE;GRIP PULSE;250+Φ6 ;500;TM219;TM2
N42 S CREW;BH;Φ4X8L;SM;PH;YZN;POT
5150
D: Entsorgungshinweis
Horizon Fitness - Produkte sind recyclebar. Führen Sie das Gerät am Ende der Nutzungsdauer einer
sachgerechten Entsorgung zu (örtliche Sammelstelle).
GB: Waste Disposal
Horizon Fitness products are recyclable. At the end if its useful life please dispose of this article correctly and
safely (local refuse sites).
F: Remarque relative à la gestion des dèchets
Horizon Fitness sont recyclables. A la fin sa durrèe d`utilisation, remettez I´appareil à un centre de gestion de
dèchets correct (collecte locale).
NL: Verwijderingsaanwijzing
Horizon Fitness producten zijn recycleerbaar. Breng het apparaat aan het einde van de gebruiksduur naar een op
recycling gespecialiseerd bedrijf (plaatselijk verzamelpunt).
E: Informaciones para la evacuaciòn
Los productos de Horizon Fitness son riciclables. Cuando se termina la vida ùtil de un aparato o una màquina,
entrèguelos an una impresa local de eleiminaciòn de residuos para su reciclaje.
I: Indicazione sullo smaltimento
I prodotti Horizon Fitness sono reciclabill. Quando I`apparecchio non servirà più, portatelo in un apposito punto di
raccolta della Vostra città (Punti di raccolta comunall).
PL: Wskazòwka dotyczàca usuwania odpadòw.
Producty firmy Horizon Fitness podlegajà recyklingowi. Pod koniec okresu o`ywalnoÈcl pros`z oddac urzàdzenie
do wlaÈciwego punkto usuwania odpadòw (lokalny punkt zbiorczy).
NO. DESCRIPTION
N44 SCREW;BH;Φ4X12L;SM;PH;BZN;POT
N45 SCREW;BH;Φ3X8L;TC;PH;FLT
N60 (UP)CONTROL PANEL;HEPD;S1.006;PARAGON
N61 OVERLAY;UP;ENG/GER;PARAGON 8-C;ERP;
N62 OVERL AY;DOWN;ENG/GER;PARAGON8-C;INCLUDE
N63 KEY;U;SHRAPNEL KEY;TM478;PARAGON 7&8-C
N64 QUIC K KEY CON WIRE;LE FT;GREEN;950MM;J
N65 QUICK KEY CON WIRE;RIGHT;YELLOW2;950M
N66 OVERLAY;ENG/GER;TM479;INCLINE;PARAGON
N68 MODULE;HANDGRIP KEYPAD BOARD;PARAGON 8-C
N69 PULSE RECEIVER SET;94032401.02;POLA
N70 M ODULE;PARAGO N 8-C ERP KEYPAD L IGHT BOAR
N71 MODULE;ERP KEY PAD BOARD;PARAGON 8 -C;
N73 K EY;PASSP ORT KE YPAD;PAR AGON 7& 8-C;S HRA
N74 SAFE SWITCH;RED;220L;(XHS2.5-2P);MAC
N75 OV ERLAY;ENG/GER;PARAGON8-C;HANDGRIP ST
N90 ADSORPTI VE PLATE;ZINC 15*25;TM257;TM25
P07 WIRE;PCB CONNECTION;650L(CKM254301-8P+SM
Q05 CAP;ARM REST;PP;BL/BLACK C
V63 LOGO LABEL;Φ27;TM479
TREADMILL OWNER’S MANUAL
Paragon 5S / 7S / 7E / 8E Owner’s Manual 070214 Rev. 2.1 © 2014 Horizon Fitness
Loading...