USER MANUAL
IMPORTANT SAFETY REMINDERS
This appliance should only be used for domestic cleaning, as
described in this user guide. Please ensure that this guide is
fully understood before operating the appliance.
GB
cigarette ends or other similar items.
GB
Do not spray with or pick up flammable liquids, cleaning fluids,
aerosols or their vapours.
Do not run over the power cord when using your appliance or
remove the plug by pulling on the power cord.
Do not leave the appliance plugged in. Always switch off and
remove the plug from the socket after use, or before cleaning
the appliance or any maintenance task.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
If the power cord is damaged stop using the appliance
immediately. To avoid a safety hazard, an authorised Hoover
service engineer must replace the power cord.
Keep hands, feet, loose clothing and hair away from rotating
brushes.
Use only attachments, consumables or spares recommended
or supplied by Hoover.
When using cleaning tools ensure that the appliance is kept in
the upright (parked) position. This will avoid possible damage
to the carpet or floor covering. When cleaning stairs, do not
position the appliance above you.
Static electricity: some carpets can cause a small build up
of static electricity. Any static discharge is not hazardous to
health.
Do not use your appliance out of doors or on any wet surface
or for wet pick up.
Do not continue to use your appliance if it appears faulty.
Hoover service: To ensure the continued safe and efficient
operation of this appliance we recommend that any servicing
or repairs are only carried out by an authorised Hoover service
engineer.
Do not stand on or wrap the cord around arms or legs when
using your appliance.
Do not use the appliance to clean animals or people.
When using the cleaning tools, ensure to always steady the
appliance with your other hand. This will ensure that the
appliance does not fall while in use.
WARNING: A thermal cut out switches off the appliance to prevent overheating
if it is used when full or there is a blockage or dirty filters. If this should
happen then switch off, unplug and correct the fault. It will take approximately
45 minutes for the cut out to automatically reset.
The Environment
The symbol on this appliance indicates that this appliance may not
be treated as household waste. Instead it must be handed over to the
applicable collection point for the recycling of electrical and electronic
equipment. Disposal must be carried out in accordance with local
environmental regulations for waste disposal. For more detailed
information about treatment, recovery and recycling of this appliance, please
contact your local city office, your household and waste disposal service or
the shop where you purchased the appliance.
This appliance complies with the European Directives 2006/95/EC,
2004/108/EC and 2011/65/EU.
Do not pick up hard or sharp objects, matches, hot ashes,
HOOVER Limited, Pentrebach, Merthyr Tydfil, Mid Glamorgan, CF48 4TU, UK
- 1-
GETTING TO KNOW YOUR CLEANER
GB
The ultra agile
way to clean
all surfaces.
TURBO BRUSH
STORED ON BOARD
CARRY HANDLE
BIN
RELEASE
HANDLE
PARQUET NOZZLE*
PET HAIR REMOVER
TURBO BRUSH*
REMOVABLE HANDLE
/ CREVICE TOOL
ON/OFF BUTTON
CORD
STORAGE
HOOKS
MULTI-FUNCTION
TOOL*
HANDLE RELEASE
BUTTON
PRE MOTOR FILTER
ACCESS BUTTON
This vacuum cleaner is
supplied with an Energy
Label as required by
European Regulation (EU)
665/2013.
(*Certain models only)
DUST BIN
EXHAUST
FILTER
DUSTING BRUSH
FLEXIBLE HOSE
UPRIGHT LOCK
RELEASE PEDAL
CARPET CARE
CONTROL SELECTOR
- 2 -
PREPARING YOUR CLEANER
GB
Remove the accessories from the
1
main packaging. You should nd the
following:
Removable Handle / Crevice Tool
Dusting Brush
Hose
Pet Hair Remover Turbo Nozzle*
Parquet Nozzle & Tube*
Multi-Function Tool*
* Certain Models only
Ensuring the cable is not trapped,
4
assemble the main body to the foot of
the cleaner.
Take the foot of the cleaner and press
2
the upright lock release pedal. Lower
the neck to the oor.
Ensure both halves of the neck are
5
pushed together and the locking clips
are fully engaged.
Insert the internal power plug on the main
3
body into the YELLOW socket located in
the neck of the cleaner.
Attach the connector hose to the foot of
6
the cleaner.
- 3 -
PREPARING YOUR CLEANER
GB
Position the cleaner in the upright
7
position. Then attach the other end of
the connector hose to the main body of
the cleaner.
Secure the dusting brush onto the dusting
brush post.
Position the hose in the hose cradle and
8
clip it in place.
Secure the turbo brush* onto the
11
separator lid.
(Certain models only)
Position the handle at the top of the
9
main body. Depress the handle release
button and slide the handle down until it
clicks into place.
IMPORTANT: If you need to access the
1210
internal electric power connector press
the upright lock release pedal and lower
the main body to the oor. Release the
locking clips for access.
- 4 -
UPRIGHT LOCK RELEASE
4
3
1
2
4
3
1
2
4
3
1
2
CARPET CARE CONTROL SELECTOR
ACTIVE STEERING
GB
Unlock the cleaner by pressing the upright lock pedal
at the rear of the cleaner with your foot.
After use return the cleaner to the upright lock position.
You will hear an audible click once locked in place.
POWER SWITCH
To switch the cleaner on or off, press the power switch
on the main body of the cleaner.
CARPET CARE CONTROL SELECTOR
The carpet care control selector raises and lowers
the height of the nozzle.
Ensure that the cleaner is in the upright (parked)
position and move the selector to the required
setting for the carpet type or oor covering.
To obtain the best performance and energy
efciency
#1
it is recommended that the adjustment
setting position 1 is used for the main cleaning
operations. The other adjustment settings are
for ease of use, use on longer pile carpets, or for
specialist cleaning tasks.
Settings
1. Best performance and energy efciency, short to
medium pile carpets, hard wooden oors, wooden
oor boards with crevices, ceramic tiles.
2. Medium pile carpets, delicate oor coverings
such as vinyl or linoleum, parquet ooring.
3. For longer pile carpets the motion resistance
may increase. Use these intermediate settings
to reduce the force required to push the vacuum
cleaner.
4. Luxury carpet and Tool mode
IMPORTANT: Using this cleaner for loop pile
carpets with pile greater than 30mm is not
recommended. Please consult the oorcare/carpet
manufacturer’s recommended cleaning instruction
before vacuuming.
IMPORTANT: When cleaning delicate hard oors
such as vinyl or linoleum the selector switch must
be moved to position 2. Failure to do so may cause
damage to the oor surface.
This vacuum cleaner is supplied with an Energy
Label as required by European Regulation (EU)
665/2013. If the label shows a red prohibition
circle on the right covering the hard oor symbol,
then this indicates that the vacuum cleaner is not
suitable for use on hard oors.
The cleaner comes with a unique steering
function that allows you to easily manoeuvre the
machine. Particularly benecial for cleaning in
awkward or conned spaces.
Twist the cleaner in the direction you wish to
turn.
CORD STORAGE
Turn the cleaner off and remove the plug. Wind the
cord around the cord storage hooks.
Rotate the storage hooks to quickly release the full
length of the power cord.
#1
NOTE: Dust pick up ability carpet, dust pick up
ability hard oor, and energy efciency in accord
with Commission Regulations (EU) 665/2013 and
(EU) 666/2013.
- 5 -
HANDLE RELEASE
GB
CLEANING TOOLS
To clean with accessories, release the handle
1
from the main body of the cleaner by pressing
the handle release button on the rear of the
cleaner and pull upwards.
Remove the hose from the foot of the cleaner
2
and insert into the removable handle / Crevice
tool.
The following accessories are available with the product:
Dusting Brush
Pet Hair Remover Turbo Brush*
Parquet Nozzle & Tube*
Multi-Function Tool*
(*certain models only)
All accessories can t directly onto the removable handle / crevice tool or on to the hose. Combine accessories
depending on use.
.
!
IMPORTANT! When using cleaning tools, the cleaner must be kept in the upright position,
particularly when cleaning stairs.
!
- 6-
CLEANING THE STAIRS
HANDLE PARK
GB
It is dangerous to place the cleaner above you when
cleaning stairs. Place the cleaner against the bottom
step.
ALWAYS work with the cleaner below you.
For more efcient storage, press the handle
release button on the rear of the product and push
downwards.
!
IMPORTANT! Extra care must be taken when
using the hose on the stairs. If the hose
becomes blocked it can exert a strong pull in
!
the direction of the cleaner.
- 7-
EMPTYING THE DUST BIN
GB
ALLERGY AND ASTHMA SUFFERERS
Lift the bin release latch and remove the dust
1
bin from the cleaner.
Hold the container using the carry handle
2
over the bin and press the bin empty button.
The dust container door will automatically
open.
When emptying any vacuum cleaner it is difcult to
avoid exposure to dust. To minimize this risk, please
follow these instructions:
Wrap the lower bin in a plastic bag and close
1
the bag tightly around the dust container
before emptying.
Press the bin empty button to empty the dust
2
2
into the plastic bag. Close the bag quickly
and dispose of it immediately.
Once emptied, gently tap or shake the container
3
to release any excess dust.
!
IMPORTANT! Do not ll above the max
level mark shown on the bin.
!
- 8 -
CLEANING THE PRE MOTOR FILTERS
!
IMPORTANT! For optimum performance,
always keep your lters clean.
!
GB
CLEANING THE EXHAUST FILTER
Lift the bin release latch and
1
remove the dust bin from the
cleaner.
Remove the turbo tool from the
top cover of the cleaner.
Separate the exible HEPA
4
lter pad from the lter frame by
pulling the tab or pushing from
underneath.
Gently tap the exible HEPA
lter pad against the side of a
bin to release excess dust.
Place the bin on a at surface
2
and lift latch to access the lter.
Wash the exible HEPA lter pad
thoroughly under hand warm
water, gently squeezing the pad
until the water runs clean.
Remove excess water by
squeezing and leave to dry for
24 hours.
DO NOT USE HOT WATER
OR DETERGENTS.
Remove the BLUE lter pack
3
(containing the exible HEPA
lter pad).
When completely dry
65
reassemble and refit filters
to cleaner.
Lift the tab on the exhaust lter cover grille and
1
remove from the cleaner.
2
Wash the exhaust lter under hand warm water
until the water runs clean. Remove excess water
by shaking and leave to dry for 24 hours.
Refit filter only when completely dry.
DO NOT USE HOT WATER OR
DETERGENTS.
!
IMPORTANT! For optimum performance, shake off excess dust from the lters regularly.
We recommend that the exible HEPA lter pad is washed every 3 MONTHS.
!
- 9 -
!
IMPORTANT! For optimum performance,
always keep your lters clean. We recommend
that the exhaust lter should be washed every
!
3 MONTHS.
CLEANING THE SEPARATION SYSTEM
!
IMPORTANT! For optimum performance,
always keep your separation system clean.
!
GB
Lift the bin release latch and
1
remove the dust bin from the
cleaner.
Remove the turbo tool from the
top cover of the cleaner.
Press the bin empty button to
4
open the bin ap.
Place the bin on a at surface
2
and lift latch to access the lter.
Pull the separation system out
of the bin.
Remove the BLUE lter pack
3
(containing the exible HEPA
lter pad).
Clean the separation system
65
with a dry cloth or dusting
brush, Once clean reassemble
and refit to the cleaner
Unscrew the retaining lock to
3
release the separation system.
- 10 -
CHANGING THE AGITATOR AND BELT
CLEARING A BLOCKAGE
GB
If your cleaner is not picking up efciently, the belt or brushes (or both) may need replacing, but rst please make
sure you have:
• Emptied the dust container
• Cleaned the lters
• Checked for blockages
1
2
Remove the carpet care control knob.
Turn the cleaner over and remove the
retaining screws attaching the brush
guard to the base.
Turn the cleaner over and remove the hood.
IMPORTANT: Switch the cleaner off and remove the plug from
the electricity supply before dismantling cleaner
!
Hold the brush assembly and stretch the belt until
4
the brush can be slotted back into the cleaner
housing.
Rotate the brush to ensure movement of the belt.
5
IMPORTANT: Switch the cleaner off and remove
the plug from the electricity supply before
!
dismantling cleaner
Check the hose by
removing it from the
handle, stretching it to full
length.
Turn the cleaner over and
rotate the brushes until
they are free to rotate. If
debris can be seen under
the hood remove the
indicated retaining screws
and clear the debris.
Check for a blockage in
the lower hose socket. To
remove the hose pull the
finger tab and pull the hose
upwards. Use a flexible rod
to remove any obstruction.
Remove brush assembly and check for wear
3
on the belt. Loop the new belt around the
motor and brush assembly.
Refit the hood ensuring the lugs along the front
6
are located in the slots on the front edge of the
baseplate. Secure the hood with the retaining
screws. Refit the carpet care control knob.
- 11 -
Open the pet hair or allergen
remover by removing the
retaining screws.
Lift the cover and remove the
blockage.
GB
User checklist
If your cleaner is not working properly run through the
following checklist.
1. Is there a working electricity supply to the cleaner?
Check with another electrical product.
2. Is the dust bin full or choked with fine dust?
To empty the dust container, see instructions on P9.
3. Is the hose blocked?
To clear a blockage, see instructions on P12.
4. Is there a blockage in the cleaner base?
To clear a blockage, see the instruction on P12.
5. Are the filters blocked?
To clean filters, see the instruction on P10.
6. Are the brushes rotating correctly?
To check the brushes, see the instructions on p12.
7. Has the cleaner overheated?
If so, it will take about 30 minutes to reset.
working order, has not been assembled in accordance with these instructions or
has been used incorrectly.
IMPORTANT INFORMATION
Hoover Service
Should you require service at any time, please contact your local Hoover Service
Ofce.
Hoover spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local
Hoover dealer or direct from Hoover. When ordering parts always quote your model
number.
Quality
Hoover’s factories have been independently assessed for quality. Our products
are made using a quality system which meets the requirements of ISO 9001
WARNING!
A thermal cut out switches off the cleaner to prevent overheating if it is used when
full or there is a blockage or dirty filters. If this should happen switch off, unplug and
correct the fault.
It will take about 45 minutes for the cut out to automatically reset.
IMPORTANT: Do not run cleaner over the supply cord as this could damage the
supply cord insulation.
GUARANTEE STATEMENT
The guarantee conditions for this appliance are as defined by our representative
in the country in which it is sold. Details regarding these conditions can be
obtained from the dealer from whom the appliance was purchased. The bill of
sale or receipt must be produced when making any claim under the terms of this
guarantee.
Subject to change without notice.
- 12 -
®
Hoover Limited
Pentrebach
Merthyr Tydl
Mid Glamorgan
CF48 4TU
HOOVER CUSTOMER HELPINE
08444 995 599
© 2014 48011581
Loading...