Hoover Encore Canisfer Cleaner with Power Nozzle, Encore S3399 Owner's Manual
Canisfer Cleaner with Power Nozzle
by Hoover
Fill in and retain
The vacuum cleaner you have just purchased is a combination
cleaner.
It has a motorized nozzie for carpet and floor cleaning and
tools for other tasks.
The model and serial number are located on the bottom’of the cleaner.
For your personal records, please enter the COMPLETE model and
serial number in the spaces provided and retain this information.
Your cleaner is model
and has serial number
It
is suggested that you attach your sales receipt to this owner’s
manual. Verification of date of purchase may be required for warranty
service of your Hoover product.
Save
Index
Assembling Cleaner
...............................
5-6
Cleaner Descriptions
.............................
34
How To Use
Cleaning Tools
.................................
6-9
Power
Nozzie
......................................
7
Suction Regulator
...............................
7
To Clean Stairs
.........
..I
......................
9
if You Have a Problem
.............................
17
important Safeguards
......
..”
......................
2
Lubrication
......................
..”.....................
17
Maintenance
Cleaning
Secondary
Fitter
..............
.13
Clearing
Obstructions
.....................
.I2
Replacing Agitator Brushes
and Brush Roll
.............................
15-16
Replacing Bag
.............................
16-11
Replacing Belt
.............................
13-15
Service
......................................................
18
Storage
.....................................................
10
0
UL
Q
0
1991 The Hoover Company
When using an electrical appliance, basic precautions should
always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
Warning.
injury:
n
To reduce the risk of fire, electric shock, or
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Donotuseoutdoors3onw&t&~rface~
Close supervision is
necessary when any appliance is used by or near
childten
Do not allow vacuum cleaner to be used as a toy or to run
unattended at
any time.
Keep hair, loose clothing, fingers, feet and all parts of body away from
openings, rotating agitator and any other moving
parts.
Do not
operate deaner in bare feet or when wearing open toe shoes or sandals.
Donotpullorcanybycord,usecordasahandle,closedooroncMd
or pull cord around sharp edges or corners Do not run appliance over
cord.Keepcordawayfromheatedsurfaces
Do not
pick
up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes
Do not use to pick up flammable or combustible liquids such as gasoline
or use in areas where they may be present
The hose contains electrical wires. Do not use if damaged, cut, or
punctured=
Avoid piddng up hard, sharp objects with the cleaner. They may
damage the deaner and the
baq
~ys~;~s~nce
before connecting or disconnecting
either
Unplug
cleaner when not in
use.
Turn off all contmls before unplugging.
A&n~disconnectcordfromelectricaloutletbeforeservkingthe
Do not
use
without dust beg and/or filters in place. Change bag fre-
quently when picking up very fine materials such as powder.
Use extra care when cleaning on stairs.
Donotputanyobjectintoopenl
s Donotusewithanyopening
blocked; keep free of dust,
knt,
ha r, and anything that may reduce air
7
flow.
Grasp the plug to disconnect from wall outlet to avoid damage to the
u~$~pz
prongs, or
receptade.
Never handle plug or appliance
with
nthedeanerhasacordreel,hddontoplugwtrilecordisbeing
rewound to prevent cord from whipping-
Theusec#anextensioncordisnotmcommendedDondusewithdamagedcordorpiug.~appibnceisnatworWngas
it
should, has been dropped, damaged, left outdoors, or dropped into
water, take it to a Hoover Factory
SeMce
Center or Authorized Hoover
Warranty Service Dealer.
Usevacwmdeanerordy~itsintendeduseasdescribedinthe
inst~~ctiorrs.
Use only attachments
recommended by The Hoover
Company; others may cause hazards.
Save these instructions!
2
Unpacking
Unpack cleaner from carton
and
identify the parts shown.
Re-
move and dispose of the car&
board packing.
A. Canister cleaner
:
B. Power nozzle
/
C. Paper bag
/
D. Extension wands and hose
/
j
The cleaner assembled will
iook
like the drawing below.
B
l&l
0
‘I
A
liiiil
0
C
-17
-18
3
1.
2.
3.
4.
5.
6.
7.
8.
9.
Cover: remove by lifting up top section of carrying handle and pulling
forward.
Carrying handle
Check bag indicator:
shows red when paper bag should be checked
for fullness.
Extension wands:
use with power nozzle. If added length is desired
when using cleaning tools, add one or both wands to hose.
Spring
latch: locks extension wands together or locks wand to nozzle
or tool.
Power
nozzle: automatically adjusts to different carpet pile heights.
Dusting brush
Crevice tool
Tool rack:
provides tool storage for crevice tool, furniture nozzle and
dusting brush, and wall/floor brush.
10. Furniture nozzle
11. Wall/Floor brush
12. Large wheels:
provide easy towing, when cleaner is pulled over
carpet, area rugs and door sills.
13. ON-OFF control:
located on top of cleaner.
14.
Cord clips:
fasten power nozzle cord to extension wands.
15. Receptacle:
connect power nozzle cord underneath hand grip.
16. Hand grip
17. Suction regulator:
close for maximum suction; open if power nozzle is
difficult to push on some carpet or if lightweight rugs or draperies are
being cleaned.
18. Plastic latch ring:
rotate to lock hand grip to extension wands or
cleaning tools.
Operate cleaner only at voltage specified on data plate on bottom of
cleaner.
This cleaner is intended for household use.
How
to
assemble
1.
Connect hose
Insert hose end with cord into
opening of cleaner, lining up largest
projection on hose with largest
notch of opening. Turn hose to the
right to tighten.
When hose is attached properly,
hose cord plug will reach to
receptacle on cleaner.
Insert plug as deeply into the
receptacle as possible.
To disconnect hose, first remove
hose cord plug from receptacle.
Then, depress latch and turn hose
to the left.
2. Attach power nozzle
and extension wands
Attach wand to power nozzle by
fitting button projection on nozzle
connector into opening in spring
latch. Be sure nozzle is locked in
place.
To release, press down on center
of latch and remove nozzle.
Attach second wand to the first.
Position cord into cord clips on
wands, placing excess cord
between nozzle and bottom cord
clip.
RD PLUG
_
_
5
Loading...