Hoover BH52200, BH52212, BH52210 User Manual

CRUISE CORDLESS VACUUM

BH52210, BH52200

BH52212

User manual.

IMPORTANT: Read carefully before assembly and use.

This product is intended for household use only. If used commercially the warranty is void.

Welcome to

Hoover

Hoover.com (8 88) 67 9-2121

Hoover will replace your batterie s under our 2 year

limited warra nty. See Warrant y for complet e details.

®

ownership.

Make it ofﬁcial.

It’s Guaranteed.

Your Guide:

Safety Instructions

Getting started with your Cruise Cordless Vacuum

Assembly

Attach the wall bracket

How to use

Accessories

Before you begin cleaning

Using your machine

Using your machine as a handheld

Using your machine to clean up high

Maintenance

How to order accessories

Need Help?

Service & Warranty

1 3 4 5 6 7 8

10

11 13 15 22 23 24

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. IF USED COMMERCIALLY WARRANTY IS VOID.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, DAMAGE OR INJURY:

•Fully assemble before operating.

• Do not use appliance on wet surfaces. Do not expose appliances to rain. Store appliances indoors.

• The charger is for indoor use only. Be sure to always keep the battery and charger indoors in a dry place.

• Do not allow to be used as a toy. Not intended for use by children age 12 and under. Close supervision is necessary when used near children. To avoid injur y or damage, keep children away from product, and do not allow children to place ﬁngers or other objects into any openings.

• Use only as described in this manual. Use only Hoover attachments and products.

• Do not use charger with damaged cord or plug. If appliance or charger is not working as it should, has been dropped, damaged, left outdoors,

1

®

recommended

or dropped into water, take it to a service center prior to continuing use.

• Do not pull or carr y charger by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not place product on cord. Do not run appliance over cord. Keep cord away from heated surfaces.

• Do not unplug charger by pulling on cord. To unplug charger, grasp the plug, not the cord.

• Do not handle charger including charger plug and charger terminals, or appliance with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air ﬂow.

• Keep hair, loose clothing, ﬁngers, and all parts of body away from openings and moving parts.

• Use extra care when cleaning on stairs. To avoid personal injury or damage, and to prevent the cleaner from falling, always place cleaner at bot tom of stairs on ﬂoor. Do not place cleaner on stairs or furniture, as it may result in injury or damage.

• Do not use to pick up ﬂammable or combustible liquids, such as gasoline, or ﬁne wood shavings, or use in areas where they may be present.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

•Do not use without Dirt Cup and/or Filters in place.

• Turn power switch off and remove battery before removing or installing brush roll.

• Always turn off this appliance before connecting or disconnecting Motorized Turbo Tool or tools.

• Do not incinerate the charger, battery, or appliance even if it is severely damaged. The batteries can explode in a ﬁre.

• This product includes rechargeable lithium-ion batteries. Do not expose batteries to high temperatures, as they may catch ﬁre and/or explode.

•Do not expose batter y to crushing, incineration or similar actions.

• Do not dispose of battery in a ﬁ re or trash compactor. See battery disposal section for directions.

•Do not attempt to disassemble bat tery.

• Unplug the charger from the outlet before any routine cleaning or maintenance.

• Leaks from battery cells can occur under extreme conditions. If any liquid gets on the skin wash quickly with soap and water. If any liquid gets into the eyes, do not rub eyes, immediately ﬂush them with clean water continuously for a minimum of 15 minutes. Seek medical attention immediately.

• Use only the charger (Hoover Part #440009553) supplied by Hoover to recharge.

®

• Use only the battery (Hoover Part # 440009633) supplied by Hoover or damage.

• Do not touch or insert objects into bat tery pack or charger terminals.

•Do not attempt to short circuit the battery or charger terminals.

®

. Other batteries may burst causing serious personal injury

WARNING: This product contains chemicals known to

the State of California to cause cancer, birth defects or reproductive harm.

WASH HANDS AFTER HANDLING.

WARNING: TO REDUCE THE RISK OF ELECTRIC

SHOCK, THE CHARGER HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER). THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET. DO NOT CHANGE THE PLUG IN ANY WAY.

2

Getting started with your Cruise cordless:

A

B

ED F

3

C

G

CARTON CONTENTS

A. Handheld B. Powered Head C. Reach Wand D. Dusting Brush E. Crevice Tool F. Pet/Stair Tool G. Articulating Dusting

Brush

All models come with a charger, battery, wall mount, 2 screws and user manual.

Contents vary dependant on the model purchased.

Assembly:

WARNING

To reduce the risk of personal injury, remove

battery before cleaning or servicing.

!!

Important

This vacuum cleaner is not free standing. In

between uses or when carrying out any

maintenance always lie ﬂat on the ﬂoor in a

suitable location so it does not become a trip

hazard or can be stepped on.

!!

Line up the connector on the Reach Wand with the Powered Head. Push the Reach Wand down onto the Powered Head until it clicks into place.

Push the Handheld down onto the Reach Wand until

2 3

it clicks into place.

The vacuum cleaner is not free standing and in between uses must always be placed in the wall bracket or laid ﬂat on the ﬂoor, in a suitable location so it does not become a trip hazard or can be stepped on.

4

Attach the wall bracket:

First, fully assemble the vacuum but do not attach the battery.

Attach the wall bracket to the handle.

Use both screws and wall plugs to secure the wall bracket to the wall. Place covers over

4

the screws.

5

2

5 6

With the wall bracket attached, stand the vacuum close to the wall, in the upright position with the Powered Head ﬂat on the ﬂoor.

Firmly press the vacuum handle into the wall bracket to secure.

Holding the wall bracket ﬁrmly in place, carefully remove the vacuum. Using a pencil make a small mark for

3

each screw.

The tools can be stored on the wall bracket.

How to use:

1. Brushbar On/Off button

2. On/Off & charging light

3. Handheld release button

4. Reach Wand

5. Power head/accessory release clip

6. Powered Head

7. Brushbar

8. Filter cover release buttons

9. Handle

10. Battery charger inlet

11. Battery release button

12. Dirt container release button (hidden)

13. Dirt release button

14. On/Off trigger

15. Continuous power latch (hidden)

16. Battery

17. Dirt container

1 2

3

8

9

14

10

15

11

4

12

16

17

5

13

6 7

6

Accessories:

Dusting Brush Pet/Stair Tool

7

Crevice Tool Articulating Dusting

Brush

All models come with a charger, battery, wall mount, 2 screws and user manual.

Contents vary dependant on the model purchased.

Before you begin cleaning:

WARNING

To reduce the risk of personal injury,

remove battery before cleaning

Slide the battery into the back of the handheld. The battery will click into position when correctly ﬁtted.

or servicing.

2

!!

To charge the machine, detach the reach wand and lie the handheld on its side on a ﬂat stable surface. You can also charge the machine while attached to the wall mount. Make sure the ﬂoorhead and wand are attached together.

For best cleaning results, ﬁlters require cleaning at least

• IMPORTANT •

every 3 months and should be replaced every 12 months

depending upon use. If the vacuum cleaner is blocked,

remove the battery before removing the blockage.

Insert the charger lead into the charger inlet

3

located on the back of the handle.

Plug the charger plug into the outlet.

4

see next page

8

Before you begin cleaning:

Do not use the vacuum cleaner when the

WARNING

machine is plugged in and charging.

The On/Off and charging light will illuminate continuously while the

5

charger is connected. Red light – The battery is charging. Green light – The battery is charged (after 5 hours).

If charging for the ﬁrst time the initial charge time is 8 hours.

9

!!

For best performance the terminals

on the battery and vacuum cleaner must

be clean and free from dust and dirt.

The life expectancy of the battery will

vary depending on the usage of the

WARNING

vacuum cleaner.

!!

Using your machine:

This vacuum cleaner has a constantly rotating brushbar when the brushbar

WARNING

‘ON’ is selected. Never leave the vacuum cleaner in one spot for an

extended period of time as this may damage the ﬂoor surface.The brushbar

should be ON for carpets and OFF for hard ﬂoors.

Squeeze the trigger located underneath the handle, the machine will switch ‘On’. The On/Off and charging light will illuminate green indicating the power is on and the machine is charged. Release the trigger to switch the machine ‘Off’.

Press the brushbar’s On/Off button to activate. Repeat this process to de-activate the brushbar. The brushbar should be switched ON for carpets and OFF for hard ﬂoors.

3

!!

Risk of personal injury – the brush

WARNING

roll may suddenly restart. Turn power

switch off and remove the battery before

cleaning of servicing the brush roll.

Squeeze the trigger and push the ‘Continuous power latch’ towards the trigger. This will lock it into the ‘On’ position and will continue to power the machine without having to hold in the trigger. Push the latch away from the trigger to

2

unlock and release the trigger.

When the vacuum cleaner is in use the On/Off and charging light will illuminate and ﬂash red when the battery is running low. When the red light ﬂashes the machine will turn off in 20 seconds. The user

4

should recharge the machine.

!!

see next page

10

Using your machine as a handheld vacuum:

Always take extra care when using the vacuum cleaner on the stairs.

Press the handheld release clip. Pull to separate the handheld

5

from the reach wand.

Choose an accessory (pictures illustrated dependent upon model).

7

11

The reach wand when attached to the Powered Head/accessory is not free standing, place safely and

6

securely to one side.

Push the chosen accessory into the handheld until it

8

clicks into place.

IMPORTANT

Not to be used for

grooming a pet.

see next page

!!

Using your machine as a handheld vacuum:

Always take extra care when using the vacuum cleaner on the stairs.

Squeeze the trigger located underneath the handle, the machine will switch ‘On’. The On/Off and charging light will illuminate green indicating the power is on and the machine is charged. Release the trigger to

9

switch the machine ‘Off’.

All of the accessories can be attached directly onto the handheld.

10

IMPORTANT

Not to be used for

grooming a pet.

Squeeze the trigger and push the ‘Continuous power latch’ towards the trigger. This will lock it into the ‘On’ position and will continue to power the machine without having to hold in the trigger. Push the latch away from the trigger to unlock and release the trigger.

!!

12

Using your machine to clean up high:

The reach wand can be used for hard to reach places.

Press the Power Head/ accessory release clip and pull to remove the Powered Head from the

13

reach wand.

Push the chosen accessory into the reach wand until it clicks into place.

3

2

4

Choose an accessory (pictures illustrated dependent upon model).

Squeeze the trigger located underneath the handle, the machine will switch ‘On’. The On/Off and charging light will illuminate green indicating the power is on and the machine is charged. Release the trigger to switch the machine ‘Off’.

see next page

Using your machine to clean up high:

The reach wand can be used for hard to reach places.

Squeeze the trigger and push the ‘Continuous power latch’ towards the trigger. This will lock it into the ‘On’ position and will continue to power the machine without having to hold in the trigger. Push the latch away from the trigger to unlock and release the trigger.

5

The Reach Wand can be used for hard to reach places and at different heights for above ﬂoor cleaning.

7

6

8

The Reach Wand can be used for hard to reach places.

The vacuum cleaner is not free standing and in between uses must always be placed in the wall bracket or laid ﬂat on the ﬂoor, in a suitable location so it does not become a trip hazard or can be stepped on.

14

Maintenance:

Removing the battery.

15

Lie the handheld on its side on a ﬂat stable surface. Press the battery release button.

WARNING

To reduce the risk of personal injury,

remove battery before cleaning

Slide the battery out from the back of the handheld.

2

or servicing.

!!

Maintenance:

Cleaning the lter and separator.

WARNING

To reduce the risk of personal injury,

remove battery before cleaning

or servicing.

Press the handheld release clip. Pull to separate the handheld from the reach wand.

Ensure the battery has been removed and hold the handheld over a bin, press the dirt release button to allow dirt and

3

debris to fall out.

The reach wand when attached to the Powered Head/accessory is not free standing. Place safely

2

and securely to one side.

Ensure the battery has been removed and hold the handheld over a bin, press the dirt release button to allow dirt and

4

debris to fall out.

16

Maintenance:

Cleaning the post–motor lter.

WARNING

To reduce the risk of personal injury,

remove battery before cleaning

or servicing.

!!

17

Press the ﬁlter cover release buttons located on both sides of the ﬁlter cover and pull to remove the ﬁlter from the machine.

Pull to separate the ﬁlter from the ﬁlter cover/holder. Tap the ﬁlter and ﬁlter cover/holder over a bin to remove any dirt/debris. Wash the ﬁlter under running water (40 degrees max).

2

Maintenance:

Emptying the dirt container.

Press the handheld release clip. Pull to separate the handheld from the reach wand.

WARNING

To reduce the risk of personal injury,

remove battery before cleaning

The reach wand when attached to the Powered Head/accessory is not free standing. Place safely

2

and securely to one side.

or servicing.

!!

Ensure the battery has been removed and hold the handheld over a bin, press the dirt release button to allow dirt and

3

debris to fall out.

Ensure the battery has been removed and hold the handheld over a bin, press the dirt release button to allow dirt and

4

debris to fall out.

18