Honeywell WEB-RL6N, WEB-RS5N Installation Manual

Spyder Model 5

WEB-RxxN ROOM CONTROLLERS

INSTALLATION GUIDE

® U.S. Registered Trademark

Copyright © 2019 Honeywell Inc. ▪ All Rights Reserved 31-00281-01 (EN1B-0664GE51 R0819)

GENERAL INFORMATION

Fig. 1. WEB-RxxN (without optional covers)

BEFORE INSTALLATION

IMPORTANT

It is recommended that the unit be kept at room
temperature for at least 24 hours before applying
power; this is to allow the evaporation of any con­densation resulting from low shipping / storage
temperatures.
US requirement, only: This device must be installed
in a UL-listed enclosure offering adequate space to
maintain the segregation of line voltage field wiring
and Class 2 field wiring.

CAUTION

To avoid electrical shock or equipment damage, you
must switch OFF the power supply before attaching
/ removing connections to/from any terminals.

Table 1. Overview of models

OS no.:

power

supply

AOs

UIs

BIs

relays(A

triacs(B

total no.

of I/Os

remarks

large housing

(7-13/16 x 4-5/16 x 2-5/16)

(198 x 110 x 57.5 mm)

WEB-RL6N

24 VAC

6

10 0 4 4 24

72-hr data retention

small housing

(6-3/8 x 4-5/16 x 2-5/16)

(162 x 110 x 57.5 mm)

WEB-RS5N

24 VAC

4 4 0 4 2

14

24-hr data retention

(A

See also section “

Relay Current Limitations” on pg. 15.

(B

See also section "Triac Current Limitations" on pg. 12.

CPU: 32-bit MK24FN Freescale Kinetis Cortex M4

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 2

DIMENSIONS AND MOUNTING

Housings

The controller is available in two housing sizes, both
conforming to IP20:

▪ WEB-RL6N (large housing): W x L x H =

4-5/16 x 7-13/16 x 2-5/16 in (110 x 198 x 59 mm) and

▪ WEB-RS5N (small housing): W x L x H =

4-5/16 x 6-3/8 x 2-5/16 in (110 x 162 x 59 mm)

See also Fig. 2 and Fig. 3.

2-1/4

(57)

1/8 (3.5)

2-5/16

(59)

1-3/4

(45)

3/8 (10)

3/8 (10)

4-5/16 (110)

2-1/8(53.5)

2-5/16(59)

2 (52)

WEB-RL6N

24 V AC

MODELS

7-13/16 (198)

2

N324V~7TN

8T~9

T0110TN11T0212T0313TN14T0415RC416RO417IN418RN19RN20IN121RO122IN223RO224IN325RO3

4

24V0524V~624V0

1

L

26

C2+ GND

28

24V~

29

27

C2-

WM130WM2

31

3832

AO134AO236AO3 AO440AO542AO6

33

GND3524V~37GND3924V~41GND4324V~

44

24V~46GND

48

UI250UI3

52

GND

54

UI656UI7

58

GND

60

UI10

45

LED

47

UI1

49

GND

51

UI453UI5

55

GND

57

UI859UI9

61

GND

62

C1+63C1- GND

64

BACnet MS/TP

SERVICE

REMOVABLE

TERMINALS

Fig. 2. WEB-RL6N dimensions in inch (mm)

2-1/4

(57)

2-5/16

()59

1/8 (3.5)

1-3/4

(45)

4-5/16 (110)

WEB-RS5N

6-3/8 (162)

7

T01

8TN9

T02

1L2

N324V~

4

24V0

5

TN

6T~10

RO411IN412RN13RN14IN115RO116IN217RO2

18

IN3

19

RO3

WM1

20

C2+23C2-

24

WM2

21

34

UI136UI237UI339UI4

35

GND38GND

26

AO12724V~28GND29AO230AO33124V~32GND33AO4

41

C1-40C1+ GND

42

BACnet MS/TP

SERVICE

22

24V~

25

GND

2-1/8(53.5)

2-5/16(59)

2 (52)

24 VAC

MODELS

3/8 (10)

3/8 (10)

REMOVABLE

TERMINALS

Fig. 3. WEB-RS5N dimensions in inch (mm)

The unit is suitable for mounting on a standard rail, on
walls, as well as in wiring cabinets or fuse boxes.

NOTE:

- IP20 provides, Ingress Protection against solid objects

over 12.5mm e.g. hands, large tools. No protection
against liquids.

- IP30 provides, Ingress Protection against solid objects

over 2.5mm e.g. wire, small tools. No protection against
liquids

Terminal Protection Covers for IP30

In the case of controllers mounted outside of a cabinet,
before applying power to the device, Terminal Protection
Covers (10-pc. bulk packs, order no.: IRM-RLC for large
housings and IRM-RSC for small housings) must be
mounted so as to provide IP30.

Fig. 4. Large housing, with terminal protection covers,

dimensions in inch (mm)

Fig. 5. Small housing, with terminal protection covers,

dimensions in inch (mm)

DIN Rail Mounting/Dismounting

MOUNTING DISMOUNTING

1.

1.

2.

2.

DIN EN 50022-35 x 7,5

RLxN: 2X
RSxN: 1X

Fig. 6. Mounting and dismounting

The unit can be mounted onto the DIN rail simply by
snapping it into place. It is dismounted by gently pulling the
stirrup(s) located at the base of the housing (see Fig. 6).

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

3 31-00281ES-01 (EN1B-0664GE51 R0819)

When mounted vertically on a DIN rail, the unit must be
secured in place with a stopper to prevent sliding.

Wall Mounting/Dismounting

The unit can be mounted on floors, walls, and ceilings in
any desired orientation. (See also section "Ambient
Environmental Limits" on pg. 17 for temperature range
restrictions with floor/ceiling mounting.)

The unit is mounted by inserting optional screws
(recommended: DIN EN ISO 7049 – ST4,2x22 – C - H)
through the corresponding screwing noses.

99.5

(3-15/16)

RLxN: 187.5 (7-3/8)

RSxN: 151.5 (6)

DIN EN ISO 7049 – ST4,2x22 – C – H

7

T018TN9T02

1L2

N324V~424V05TN

6T~10

RO411IN412RN13RN14IN115RO116IN217RO218IN319RO3

WM1

20

C2+23C2-

24

WM2

21

34

UI136UI237UI339UI435GND38GND

26

AO12724V~28GND29AO230AO33124V~32GND33AO4

41

C1-40C1+ GND

42

BACnet MS/TP

SERVICE

22

24V~

25

GND

Fig. 7. Drilling template (view from above)

After mounting the unit onto the wall, snap the appropriate
terminal protection covers (see Fig. 4 and Fig. 5 on pg. 2)
into place onto the housing by hand.

NOTE: In the case of wall-mounting, two optional terminal

protection covers (in the case of the WEB-RL6N
[large housings]: IRM-RLC; in the case of the WEB­RS5N [small housings]: IRM-RSC) must be
installed in order to comply with IP30.

The covers can be fixed into place using optional screws
(recommended: DIN EN ISO 7049 – ST2,9x9,5 – C (F) – H).
To remove a cover, place a screwdriver in the two leverage
slots (marked with arrows) and pry it loose.

TERMINAL ASSIGNMENT

General

For a complete list of all terminals and a description of their
functions, see Table 2 and Table 6 on pg. 4 and pg. 6.

NOTE: All terminal blocks capable of carrying either low

voltage or line voltage are orange-colored.

Depending upon the given hardware model, the delivery
includes a plastic bag containing additional, removable
terminal blocks.

Every controller features a terminal assignment label on
the top of the housing.

Power Supply Terminals

▪ In the case of the 24VAC models, power is supplied via a

removable terminal plug (terminals 3 and 4).

See also section "Power Supply" on pg. 9.

Input / Output Terminals

The controller features rows of terminal blocks on the top
and bottom.

▪ In the case of the WEB-RL6N (large housing), the

controller has double rows of analog outputs (AOs) and
universal inputs (UIs) at the top and a single row of
binary outputs (BOs) - triacs (TRs) and relay outputs
(ROs) - at the bottom.

▪ In the case of the WEB-RS5N (small housing), the

controller has a single row of analog outputs (AOs) and
universal inputs (UIs) at the top and a single row of
binary outputs (BOs) - triacs (TRs) and relay outputs
(ROs) - at the bottom.

NOTE: According to VDE guidelines, it is not allowed to

mix low-voltage and high-voltage signals on the
relays and triacs.

See also section "I/O Terminals" on pg. 12.

Communication Interfaces

All models of the controller feature the following communi­cation interfaces:

▪ A Sylk Bus interface (WEB-RS5N: terminals 20 and 21;

WEB-RL6N: terminals 30 and 31), for connection to
TR40x/42x Wall Modules;

▪ A BACnet MS/TP interface (WEB-RS5N: terminals 40,

41, and 42; WEB-RL6N: terminals 62, 63, and 64);

▪ An RJ45 connector for future use with BACnet WiFi

Adapter;

▪ A second RS485 interface for future use with Modbus.

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 4

Table 2. WEB-RS5N Room Controllers: Overview of terminals and functions (by model)

term.

printing

function

WEB­RS5N

1, 2

--

--

--

3, 4

24V~, 24V0

Removable 24 VAC power supply input and aux. output voltage (24 VAC) for all triacs

X

3, 4

24V~, 24V0

Aux. output voltage (24 VAC) for all triacs

X

5

TN

Aux. term. for triac neutral wiring (internally connected with terminal 8)

X

6

T~

Triac input voltage (24 VAC for all triacs; triac-switched

X

7

T01

Triac-switched output

X

8

TN

Aux. term. for triac neutral wiring (internally connected with terminal 5)

X

9

T02

Triac-switched output

X

10, 11

RO4, IN4

Output of Relay 4, Input for Relay 4

type 2

12, 13

RN, RN

Aux. terminals for relay neutral wiring

X

14, 15

IN1, RO1

Input for Relay 1, Output of Relay 1

type 1

16, 17

IN2, RO2

Input for Relay 2, Output of Relay 2

type 1

18, 19

IN3, RO3

Input for Relay 3, Output of Relay 3

type 1

20, 21

WM1, WM2

Removable interface for Sylk Bus

X

22, 23,
24, 25

24V~, C2+,
C2-, 24V0

Aux. power (24 VAC 20%, 50/60 Hz), RS485 Modbus interface and corresponding GND

X

26

AO1

Analog Output 1

type 2

27

24V~

24 VAC power for field devices

X

28

GND

Ground for AOs

X

29

AO2

Analog Output 2

type 1

30

AO3

Analog Output 3

type 1

31

24V~

24 VAC power for field devices

X

32

GND

Ground for AOs

X

33

AO4

Analog Output 4

type 1

34

UI1

Universal Input 1

type 1

35

GND

Ground for UIs

X

36

UI2

Universal Input 2

type 1

37

UI3

Universal Input 3

type 1

38

GND

Ground for UIs

X

39

UI4

Universal Input 4

type 1

40, 41,
42

C1+, C1-, GND

Removable BACnet MS/TP interface and corresponding GND

X

Relay output types: See Table 3. Universal input types: Table 4. Analog output types: See Table 5.

-- : Terminal not used.
X : Terminal used.
Type x: Type of an I/O as per its characteristic. Mode details given on each type in following tables.

Table 3. Relay output types and characteristics

type 1

(standard)

type 2

(high in-rush current)

corresponding ROs of WEB-RS5N

RO1, RO2, RO3

RO4

corresponding ROs of WEB-RL6N

RO2, RO3

RO1, RO4

contact

N.O.

N.O.

min. load

5 VAC, 100 mA

24 VAC, 40 mA

switching voltage range

15 to 253 VAC

15 to 253 VAC

max. continuous load at 250 VAC (cos φ = 1)

4 A

10 A

max. continuous load at 250 VAC (cos φ = 0.6)

4 A

10 A

in-rush current (20 ms)

--

80 A

usage

fan motor

fan motor

NOTE: The max. sum load of all relay currents at the same time is 14 A.

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

5 31-00281ES-01 (EN1B-0664GE51 R0819)

Table 4. Universal input types and characteristics

type 1

type 2

type 3

UI1, UI2, UI3, UI4,

UI5, UI6

UI7, UI8, UI9,

UI10

UI1, UI2, UI3

dry contact (closed: res. <10 kΩ; open: res. > 20 kΩ; max. 0.2 Hz;
pull-up voltage: 10 V)

X X --

dry contact (closed: res. <10 kΩ; open: res. > 20 kΩ; max. 0.2 Hz;
pull-up voltage: 24 V);

--

--

X

fast binary (=counter) input with below characteristics.

(max. 30 Hz; pulse ON = min. 16 ms; pulse OFF = min. 16 ms; closed: voltage < 1 V;
open: voltage > 5 V; pull-up voltage: 10 V)

X X --

fast binary (=counter) input with below characteristics.

(max. 30 Hz; pulse ON = min. 16 ms; pulse OFF = min. 16 ms; closed: voltage < 1 V;
open: voltage > 5 V; pull-up voltage: 24 V)

--

--

X

0(2) to 10 V X X

--

NTC20kΩ X --

--

SetPoint and FanSpdSW

X

--

--

NTC10kΩ (Type II)

X

--

--

PT1000 + Ni1000TK5000

-- X --

Table 5. Analog output types and characteristics

type 1

type 2

type 3

type 4

type 5

output voltage

0-11 V

output current

0-1 mA

0-5 mA

0-10 mA

0-20 mA

-1- +1 mA

min. accuracy

±150 mV

max. ripple

±100 mV

accuracy at zero point

0-200 mV

±150 mV

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 6

Table 6. WEB-RL6N Room Controllers: Overview of terminals and functions (by model)

term.

printing

function

WEB-RL6N

1, 2

--

--

--

3, 4

24V~, 24V0

Removable 24 VAC power supply input

X

5, 6

24V~, 24V0

Aux. output voltage (24 VAC) for all triacs

X

7

TN

Aux. terminal for triac neutral wiring (internally connected with terminals 10 and 13)

X

8

T~

Triac input voltage (24 VAC) for all triacs; triac-switched

X

9

T01

Triac-switched output

X

10

TN

Aux. terminal for triac neutral wiring (internally connected with terminals 7 and 13)

X

11

T02

Triac-switched output

X

12

T03

Triac-switched output

X

13

TN

Aux. terminal for triac neutral wiring (internally connected with terminals 7 and 10)

X

14

T04

Triac-switched output

X

15

--

Not used

--

16, 17

RO4, IN4

Output of Relay 4, Input for Relay 4

type 2

18

RN

Aux. terminal for relay neutral wiring

X

19

RN

Aux. terminal for relay neutral wiring

X

20, 21

IN1, RO1

Input for Relay 1, Output of Relay 1

type 2

22, 23

IN2, RO2

Input for Relay 2, Output of Relay 2

type 1

24, 25

IN3, RO3

Input for Relay 3, Output of Relay 3

type 1

26, 27, 28,
29

C2+, C2-, 24V0, 24V~

RS485 Modbus interface, corr. GND, + aux. power (24 VAC 20%, 50/60 Hz)

X

30, 31

WM1, WM2

Removable interface for Sylk Bus

X

32

AO1

Analog Output 1

type 3

33

GND

Ground for AOs

X

34

AO2

Analog Output 2

type 3

35

24V~

24 VAC power for field devices

X

36

AO3

Analog Output 3

type 1

37

GND

Ground for AOs

X

38

AO4

Analog Output 4

type 1

39

24V~

24 VAC power for field devices

X

40

AO5

Analog Output 5

type 1

41

GND

Ground for AOs

X

42

AO6

Analog Output 6

type 1

43

24V~

24 VAC power for field devices

X

44

24V~

24 VAC power for field devices

--

45

LED

Output to LED of CLCMx

--

46

GND

Ground for UIs

X

47

UI1

Universal Input 1

type 1

48

UI2

Universal Input 2

type 1

49

GND

Ground for UIs

X

50

UI3

Universal Input 3

type 1

51

UI4

Universal Input 4

type 1

52

GND

Ground for UIs

X

53

UI5

Universal Input 5

type 1

54

UI6

Universal Input 6

type 1

55

GND

Ground for UIs

X

56

UI7

Universal Input 7

type 2

57

UI8

Universal Input 8

type 2

58

GND

Ground for UIs

X

59

UI9

Universal Input 9

type 2

60

UI10

Universal Input 10

type 2

61

GND

Ground for UIs

X

62, 63, 64

C1+, C1-, GND

Removable BACnet MS/TP interface and corresponding GND

X

Relay output types Table 3: See. Universal input types: Table 4. Analog output types: See Table 5.

--: Terminal not used.

X: Terminal used.
Type x: Type of an I/O as per its characteristic. Mode details given on each type in following tables.

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

7 31-00281ES-01 (EN1B-0664GE51 R0819)

Fig. 8. WEB-RS5N (24 VAC models) and example wiring

87 6543

21

RJ45 INTERFACE

20

WM121WM2

26

AO1

32

GND

34

UI1

36
UI237UI3

1

TEMP

2

SETP

29

AO230AO3

33

AO4

THERM.

COOL

THERM.

HEAT

5

TN

OCCUPANCY CONTACT

28

GND

27

24V~

31

24V~

39

UI4

35

GND

38

GND

40

C1+41C1-42GND

7 8

2,3,
5,6

4

24V~

0...10V

ELECTR.

REHEATER

3-SPEED

FAN

10

RO4

11

IN4

14

IN1

15

RO1

16

IN2

17

RO218IN319RO3

3

24V~

4

24V0

NL

24V~

24V0

N L

6

T~

7

T01

8

TN

9

T02

12RN13

RN

3

COM

TR40x/TR42x

WALL MODULE

70

°F

LINE VOLTAGE

LINE VOLTAGE

F1

PROPORTIONAL

DAMPER

ACTUATOR

GND

T WALL MODULE7xxxx

Niagara

workbench

BACnet MS/TP

Fig. 9. WEB-RS5N (24 VAC models) and example wiring (with actuator powered by extra transformer)

NOTE: See Fig. 11 on pg. 9 for information on how to connect multiple controllers to a single power supply.

WEB-8000/

CIPer Model 50

70

°

F

CLCMx WALL MODULE

CLCMx

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 8

TR40x/TR42x

WALL MODULE

WEB-8000/

CIPer Model 50

°F

70

Fig. 10. WEB-RL6N (24 VAC models) and example wiring

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

9 31-00281ES-01 (EN1B-0664GE51 R0819)

POWER SUPPLY

General Information

CAUTION

To prevent a risk of injury due to electrical shock
and/or damage to device due to short-circuiting,
low-voltage and high-voltage lines must be kept
physically separate from one another.
Further, to prevent a risk of short-circuiting and
damage to your unit, do not reverse the polarity of
the power connection cables, and avoid ground
loops (i.e., avoid connecting one field device to
several controllers).

NOTE: All wiring must comply with applicable electrical

codes and ordinances. Refer to job or manu­facturers’ drawings for details. Local wiring guide­lines (e.g., IEC 364-6-61 or VDE 0100) may take
precedence over recommendations provided in
these installation instructions.

NOTE: To comply with CE requirements, devices having a

voltage of 50-1000 VAC or 75-1500 Vdc but
lacking a supply cord, plug, or other means for
disconnecting from the power supply must have
the means of disconnection incorporated in the
fixed wiring. This means of disconnection must
have a contact separation of at least 3 mm at all
poles.

Wiring

24 VAC Terminals for Auxiliary or Field Devices

All 24 VAC auxiliary power supply terminals support 1 x 2.5
mm2 or 2 x 1.5 mm2 wiring.

24 VAC Models

The 24 VAC models are powered via a black removable
terminal plug (terminals 3 and 4), thus allowing daisy chain
wiring of the power supply. See also Fig. 1. These terminals
support 1 x 2.5 mm2 or 2 x 1.5 mm2 wiring.

Fig. 101. Multiple 24 VAC models connected to single

power supply

Communication / Signal Terminals

All other communication / signal terminals (except for the
Sylk Bus – see Table 10 on pg. 15) support 1 x 2.5 mm2 or 2
x 1.5 mm2 wiring. Two wires with a total thickness of 2.5
mm2 (14 AWG) can be twisted together and connected
using a wire nut (include a pigtail with this wire group and
attach the pigtail to the individual terminal block).
Deviations from this rule can result in improper electrical
contact. Local wiring codes may take precedence over this
recommendation.

Electrical Data

WEB-RL6N, WEB-RS5N (24 VAC)

Power via terminals 3,4: 24 VAC 20%, 50/60 Hz.

Max. current consumption (when unloaded): 300 mA.
Max. current consumption (when loaded): 900 mA.

A 24 VAC model is "loaded" when, besides the inherent load
(300 mA), an additional sum load resulting from max. 600
mA is applied to the 24 VAC output terminals. The max.
unloaded output voltage at terminals 3 and 4 (WEB-RS5N)
or terminals 5 and 6 (WEB-RL6N), respectively, is identical
with the output voltage of the external supplying
transformer. A maximum 22VA rating transformer is
needed when loaded.

FREELY PROGRAMMABLE
APPLICATIONS

All models can be used with freely programmable appli­cations. The application engineer performs this task on a
PC on which the Niagara software program has been
installed (see also corresponding Technical Literature
listed in Table 11 on pg. 18).

Supported Actuators

The application supports a variety of actuators.

• Analog 0(2) - 10 V

• Floating

• PWM

• Staged actuators

• 6-way valve actuators

Supported Sensors

A variety of sensors (e.g., room temperature sensors, supply
temperature sensors, condensation switch, window
sensors, occupancy sensors, card readers, etc.) may be
used to optimize control quality.

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 10

Automatic MAC Addressing

In contrast to other controllers (e.g., WEB-8000 controllers,
whose MAC addresses must be assigned manually – done
using their two dip switches), the WEB-RxxN controller
features automatic MAC addressing.

The MAC addresses which the individual WEB-RxxN con­trollers in the BACnet MS/TP channel assign to themselves
are not assigned in sequential order.

Rather, they assign those numbers (MAC Addr) in the range
of 1 to maxMaster currently not in use by another device in
the BACnet MS/TP channel (the MAC Addr of "0" is reserved
by default for the router / plant controller, itself).

All WEB-RxxN controllers are BACnet MS/TP masters.
Every master performs periodic polling for the possible
appearance of new masters. Each master "knows" the
identity of the "next" master (i.e., that WEB-RxxN controller
with the next-highest MAC Addr) on the BACnet MS/TP bus
and to which it must therefore pass the token. The polling
process includes a search for new masters which might
have MAC addresses lying between its own MAC address
and that of the "next" master.

The property maxMaster specifies the highest-allowable
address for master nodes. maxMaster is set to 32 by
default, thus guaranteeing that, on a BACnet MS/TP bus
with, e.g., 32 WEB-RxxN controllers, all of the other WEB­RxxN controllers will be found. Both the property
maxMaster and the property MAC address are writeable
properties that can be changed.

NOTE: You should not attempt to program a MAC Addr

outside the range of 1 to maxMaster.

#maxMaster

ANCILLARY WEBs MSTP CONTROLLER (WITH MANUAL MAC ADDRESSING)

WEB-RxxN CONTROLLER (WITH AUTOMATIC MAC ADDRESSING)

WEB-8000/

CIPer Model 50 etc.

Fig. 12. Automatic MAC addressing

In the scenario depicted in Fig.15, some of the controllers
in the BACnet MS/TP channel do not feature automatic
MAC addressing; rather, their MAC addresses were
assigned manually (e.g., using their two dip switches). Thus,
when a new WEB-RxxN is added to the channel, when its
automatic MAC addressing function is triggered, it will
assign itself an available (i.e., unoccupied) MAC address.

During the automatic MAC addressing process, LED
behavior #7 (see Table 7) is displayed.

OPERATOR INTERFACES

LEDs

The controller features the following LEDs:

T2 R2 T1 R1

!

Fig. 113. Controller LEDs

Table 7. Description of LED behaviors

symbol

color

function, description

T2

yellow

Not used

R2

yellow

Not used

T1

yellow

LED indicating transmission of
communication signals via the BACnet
MS/TP interface.

R1

yellow

LED indicating reception of communication
signals via the BACnet MS/TP interface.

!

yellow

Status LED indicating firmware problems,
hardware problems, etc. (see Table 8).

green

Power LED indicating firmware problems,
hardware problems, etc. (see Table 8).

Table 8. Status LED and power LED behaviors

#

Mode

Power LED

(green)

Status LED

(yellow)

1

Power failure

Stays OFF

Stays OFF

2

Device error*

Stays ON

Stays ON

3

Firmware download

ON/OFF (1 Hz)

ON/OFF (1 Hz)

4

No application

ON/OFF (0.5 Hz)

ON/OFF (0.25 Hz)

5

Broken sensor

ON/OFF (0.25 Hz)

Stays ON

6

Short-circuiting

ON/OFF (0.5 Hz)

Stays ON

7

Auto-MAC

ON/OFF (1 Hz)

ON/OFF (0.5 Hz)

8

Unacknowledged
alarm

ON/OFF (2 Hz)

ON/OFF (2 Hz)
9

Normal operation

ON/OFF (0.5 Hz)

Stays OFF

*Please return the controller for repair. Contact Honeywell
WEBs Customer Care for assistance.

Service Button

The Service Button is used to trigger dedicated events.

It is important to distinguish different controller behaviors
which are elicited depending upon whether the Service
Button is pressed when the controller is powering up or
when it is in normal operation. See the following sub­sections.

Pressing Service Button during Power-Up

During controller power-up, pressing the Service Button
until LED behavior #3 (see Table 8) is displayed will reset
the controller to its factory settings, which are as follows:

▪ The application is cleared from the controller.

▪ The MAC address will be set to 0xFF, meaning that the

controller will now search for a new mac address (Auto
MAC will be automatically triggered after controller
power-up).

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

11 31-00281ES-01 (EN1B-0664GE51 R0819)

▪ The maxMaster setting will revert to its default value of

32.

▪ The Max info frames will revert to 10.

▪ The device instance will revert to its default of 4194302.

▪ The device name will revert to WEB-[ModelName].

▪ The values of automac min_mac and max_mac will be

reset to 1 and maxMaster, respectively.

Pressing Service Button during Normal Operation

During normal operation of the controller, a short press (< 1
sec) of the Service Button will cause a Service Pin Message
(BACnet WhoAmI as a Private Transfer (SerialNo. = 130)) to
be sent.

COMMUNICATION INTERFACES

BACnet MS/TP Interface

The controller features an RS485 interface (WEB-RL6N:
terminals 62, 63, and 64; WEB-RS5N: terminals 40, 41, and

42) suitable for BACnet MS/TP communication. The
terminal block containing it is black. The cable length
affects the baud rate. See Table 9

Table 9. Baud rate vs. max. cable length

baud rate

max. cable length (L)

9.6, 19.2, 38.4, 57.6, and 76.8
kbps

(3600 ft) 1200 m

The controller supports auto-baud rate adaption for
BACnet MS/TP communication at all of the
aforementioned baud rates (default: 38.4 kbps).

For information on wire gauge, max. permissible cable
length, possible shielding and grounding requirements,
and the max. number of devices which can be connected to
a bus, refer to standard EIA-485.

Connecting to BACnet MS/TP Buses

The controller communicates via its BACnet MS/TP
interface with other BACnet MS/TP-capable devices (e.g.,
other room controllers or MS/TP controllers). In doing so,
the following considerations should be taken into account.

▪ Max. BACnet MS/TP bus length (= "L" in Fig.17): See

Table 9.

▪ Twisted-pair cable, e.g.:

- AWG 18;

- J-Y-(St)-Y 2 x 2 x 0,8;

- CAT 5,6,7 cable – use only one single pair for one

bus;

- Belden 9842 or 9842NH;

and daisy-chain topology.
▪ Must conform to EIA-RS485 cabling guidelines and

ANSI/ASHRAE Standard 135-2010.

▪ Max. no. of BACnet MS/TP devices per BACnet MS/TP

channel (interface) of the plant controller: 32 unit loads.
(Each WEB-RxxN controller represents ¼ of a unit load,
and auto MAC addressing supports a max. of 62
addresses). Effectively, the maximum possible number
of BACnet MS/TP devices (= "N" in Fig.17) per channel of
the Master, incl. the Master itself, is 64.

- maxMaster is set by default to 32 devices (this is

because some plant controllers support only 32
devices). In the event that you have a plant controller
capable of supporting more than 32 devices, it will
therefore be necessary for you to increase the
maxMaster setting to the actual required number of
devices (e.g., to 64). Refer to the IRM BACnet Device
Manager – User Guide (EN2B-0414GE51) for more
information on how to do this.

- Depending upon your actual performance needs

and required communication rates, we recommend
connecting a lower number of BACnet MS/TP
devices per channel.

WEB-8000/

CIPer Model 50

NOTE 2

WEB-RS5N

WEB-RL6N

Fig. 124. Connection to a BACnet MS/TP Bus

NOTE 1 : If any of the devices are electrically isolated, it is

recommended that those devices be connected to
signal ground.

NOTE 2 : The 120-Ohm termination resistor must be

inserted directly into the terminals of the final
BACnet MS/TP device.

NOTE 3 : If shielding is used, the shielding of each

individual bus segment should be separately
connected at one end to earth.

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 12

Sylk Bus

Sylk Bus-capable devices (e.g., the TR40x / T42x) can be
connected to the controller's Sylk Interface (WEB-RS5N:
terminals 20 and 21; WEB-RL6N: terminals 30 and 31).
Specifically:

▪ A max. of three TR40x / T42x can be supported by a

single controller.

▪ The Sylk Bus is single pair, and polarity-insensitive.

▪ Max. current provided at the Sylk Bus interface: 96 mA.

Table 10. Recommended max. distances from controller

to TR40x / T42x wall modules

Sl.

no.

single twisted pair, non-

shielded, stranded or solid (A

standard non-twisted

thermostat wire, shielded

or non-shielded,

stranded or solid

(B, (C

1

18 - 22 AWG

(0.33to0.82

mm2)

24 AWG

(0.20 mm2)

18 - 24 AWG

(0.20to0.82 mm2)

2

500 ft

(150 m)

400 ft

(120 m)

100 ft (30 m)

(A

As a rule of thumb, single twisted pair (two wires per cable,
only), thicker gauge, non-shielded cable yields the best results
for longer runs.

(B

The 100 ft (30 m) distance for standard thermostat wire is
conservative but is meant to reduce the impact of any sources of
electrical noise (incl. but not limited to VFDs, electronic ballasts,
etc.). Shielded cable recommended only if there is a need to
reduce the effect of electrical noise.

(C

These distances apply also for shielded twisted pair.

I/O TERMINALS

CAUTION

Failure to observe the following max. permissible
current outputs of the power output terminals will
result in damage to the device.

Max. Current Output of Power Output
Terminals of 24 VAC Controllers

The 24 VAC power output terminals of the WEB-RL6N
controllers are terminals 5, 6, 35, 39, 43, and 44 plus pin 4
of the controller's RJ45 interface.

The 24 VAC power output terminals of the WEB-RS5N
controllers are terminals 3, 4, 22, 23, 24, 25, 27, and 31
plus pin 4 of the controller's RJ45 interface.

The maximum permissible combined current output of
these 24 VAC power output terminals is 300 mA.

Relay Outputs

CAUTION

Mixing of different voltages within the relay block is
not allowed.

The terminal blocks containing the controller's relay
outputs are orange. Relay output types: See Table 3 pg.4.

NOTE: If inductive components are to be connected to

the relays and if these relays switch more often
than once every two minutes, these components
must be prevented from causing harmful
interference to radio or television reception
(conformance with EN 45014).

Relay Current Limitations

If the triacs are supplied with current from an external
source, then a maximum of two relays may be loaded with a
max. of 4 A per relay, even if two triacs are each
simultaneously loaded with max. 300 mA.

If the triacs are supplied with current from an internal
source, a maximum of two relays may be loaded as follows:
a max. load of 4 A for a relay serving a fan and a max. load
of 10 A for a relay serving a reheat, even if one triac is
simultaneously loaded with 300 mA.

Triac Outputs

NOTE: Recommended fuse (F1): 1.25 A time-lag fuse

(IEC). User must consider the correct voltage and
max. breaking capacity / interrupting rate (line
voltage urgently requires high breaking capacity /
interrupting rate).

The terminal blocks containing the controller's triac
outputs are orange.

These triac outputs can be used for a variety of different
functions, e.g., for connection to either a floating drive or to
a thermal actuator. Once the triac outputs have been
programmed, the corresponding devices can then be
connected to them directly.

NOTE: The VC6983 actuator is intended for use at relay

outputs, only and must not be used at the con­troller's triac outputs.

Triac Current Limitations

The maximum allowed current with which the ensemble of
a controller's triacs may be loaded is dependent upon
whether the given model is powered with 24 VAC, upon
whether the outputs are supplied by the controller's
internal transformer or by an external current supply).
Specifically:

▪ In the case of 24 VAC models, the ensemble of a con-

troller's triacs may be loaded with 600 mA.

However, regardless of model and regardless of whether
the triacs are supplied internally or externally, a single triac
must never be loaded with a current of more than 300 mA
(320 mA for maximum 2 minutes).

Nevertheless, the ensemble of triacs can be loaded for very
short periods of time (on the order of milliseconds) with a
current on the order of 2500 mA typically encountered
when switching on multiple thermal actuators.

Universal Inputs

The terminal blocks containing the controller's universal
inputs are blue. Universal input types: See Table 4.

The universal inputs are protected against voltages of max.
29 VAC and 30 VDC (due to, e.g., miswiring).

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

13 31-00281ES-01 (EN1B-0664GE51 R0819)

Bias Resistors

Each universal input is equipped with one bias resistor. See
Fig.18.

UI

GND

SENSOR

RDOWN

RBIAS

RSER

S2

S1

ADC

VUP

Fig. 135. Schematic of universal inputs and bias resistors

LEGEND:

VUP = 10 V.

R

BIAS

= Bias resistor (with a resistance of 24.9 kΩ in the

case of NTC10kΩ (Type II) and NTC20kΩ sensor
inputs, and 7.5 kΩ in the case of Pt1000 sensor
inputs); can be switched OFF via software by S1 to
support 0to10 V inputs without bias current (high
impedance).

R

SER

= Series resistor for voltage dividing and filtering

(with a resistance of 150 kΩ).

R

DOWN

= An internal load resistor (with a resistance of

49 kΩ); depending upon the given type of
connected sensor, the firmware may switch this
resistor OFF.

Analog Outputs

The terminal blocks containing the controller's analog
outputs are green. Analog output types: See Table 5 on
pg.5.

The analog outputs of the WEB-RL6N controllers (large
housing) are protected against voltages of max. 29 VAC
and 30 VDC (due to, e.g., miswiring).

NOTE: Connecting 24 VAC to any analog output of the

WEB-RS5N controllers (small housing) will
damage the hardware.

WALL MODULES

The TR40x/TR42x/CLCMx Wall Modules can be used in
conjunction with the controller to perform room
temperature sensing, setpoint adjustment, fan speed
manual override, and occupancy override. The wall modules
supported by the WEB-RS5N and WEB-RL6N are; TR40,
TR40-H, TR40-CO2, TR40-H-CO2, TR42-H, TR42-CO2,
TR42_H_CO2, CLCM1T, CLCM2T, CLCM4T, CLCM5T,
CLCM6T.

Further, the LED and LCD of the wall modules can be
programmed to provide information about:

▪ any override of the controller by, e.g., pressing the

"occupancy" button of the wall module or receipt by the
controller of a BACnet MS/TP network command (see
section "LED of CLCMxT Programmed to Display Info on
Overrides" below);

▪ the controller's effective occupancy mode (see section

“LED of CLCMxT Programmed to Display Info on
Occupancy” below).

NOTE: The intended use of the wall module's buttons

must be programmed using the Niagara tool.

See also corresponding Technical Literature listed in Table
11 on pg. 18.

Programming of Wall Module LED / LCD

The LED of a CLCMxT Wall Module can be programmed to
provide information about, e.g., overrides or effective
occupancy modes.

The LCD of the TR42x can likewise be programmed to
display such information.

LED of CLCMxT Programmed to Display Info on
Overrides

The LED of a CLCMxT Wall Module connected to the con­troller can be programmed to indicate if an override has
been activated because either the wall module's override
button has been pressed or the controller has received a
BACnet MS/TP network command. Specifically, the
following modes are supported:

▪ NO OVERRIDE: If the wall module's LED is OFF, then no

override is currently in effect.

▪ OVERRIDE OCCUPANCY: If the wall module's LED is ON

continuously, then the wall module's override button or a
BACnet MS/TP network command has placed the con­troller into the "occupied" or "override" mode (but if the
override button is again pushed or if a cancellation
network command is received or if the override time
expires, the controller will return to its scheduled
occupancy mode, and the wall module's LED will behave
accordingly).

▪ OVERRIDE HOLIDAY: If the wall module's LED flashes 2

sec OFF and 1 sec ON, then the controller has received a
network command and been placed in the "holiday"
mode.

▪ OVERRIDE UNOCCUPIED: If the wall module's LED

flashes once per sec, then the wall module's override
button or a network command has placed the controller
into the "unoccupied" mode (however, if the override
button is again pushed or if a cancellation BACnet
MS/TP network command is received, the controller will
return to its scheduled occupancy mode, and the wall
module's LED will behave accordingly).

▪ If the wall module's LED flashes twice per sec, then a

BACnet MS/TP network command has placed the con­troller into either the "standby" or the "occupied" mode.

LED of CLCMxT Programmed to Display Info on
Occupancy

The LED of a CLCMxT Wall Module connected to the
controller can also be programmed to indicate the

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 14

controller's effective occupancy mode. Specifically, the
following modes are supported:

▪ UNOCCUPIED: If the wall module's LED is OFF, then the

controller is in the "unoccupied" mode.

▪ STANDBY: If the wall module's LED flashes once per sec,

then the controller has received a network command
and been placed in the "standby" mode.

▪ OCCUPIED: If the wall module's LED is ON, then the

controller is in the "occupied" mode.

▪ BYPASS: If the wall module's LED is ON continuously,

then the controller has received a network command
and been placed in the "bypass" mode.

▪ HOLIDAY: If the wall module's LED is OFF, then the

controller has received a network command and been
placed in the "holiday" mode.

LCD of TR42x Programmed to Display Info on
Occupancy

The LCD of TR42x connected to the controller can be
programmed to display various texts and symbols to
indicate the effective occupancy mode of the controller.
The following then applies.

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

15 31-00281ES-01 (EN1B-0664GE51 R0819)

Unoccupied Mode

Fig. 146. Example "unoccupied" screens

If is displayed, the controller is in the "unoccupied"
mode.

The user can override the "unoccupied" mode by touching
the upper right softkey. An intermediate screen will then
flash for a few seconds, allowing the user to either cancel
(upper left softkey) or confirm (upper right softkey). If the
user neither cancels nor confirms, this will be considered a
confirmation, and the controller will be placed in the
"overridden to bypass" mode. If, on the other hand, the user
cancels, the controller will revert to the "unoccupied" mode.

If is displayed, the controller is in the "occupied"
mode.

Standby Mode

Fig. 157. Example "standby" screens

If is displayed, the controller is in the "standby" mode.

The user can override the "standby" mode by touching the
upper right softkey. An intermediate screen will then flash
for a few seconds, allowing the user to either cancel (upper
left softkey) or confirm (upper right softkey). If the user
neither cancels nor confirms, this will be considered a
confirmation, and the controller will be placed in the
"overridden to bypass" mode. If, on the other hand, the user
cancels, the controller will revert to the "standby" mode.

Occupied Mode

Fig. 168. Example "occupied" display

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 16

LCD of TR42x Configured to Display Info on Fan

If

OFF

is displayed, the fan is switched OFF. Depending
upon the given application configuration, the effective
control mode for underfloor heating, radiator, ceiling
heating, and ceiling cooling can then be switched OFF as
well.

Configuring the TR42x for Heating / Cooling

With the TR42x, the user can select whether he wants to
have:

▪ cooling (C),

▪ heating ( ), or

▪ cooling plus heating (auto) (

H/C

AUTO

).

By doing so, inadvertent heating or cooling is prevented.
Selecting "auto" results in automatic switching between
cooling and heating.

To make these selections, the user must enter the
expanded menu (see section below).

Expanded Menu

The user can enter the expanded menu at any time (i.e., in
any mode). This is done by touching both upper softkeys
simultaneously (see Fig. 3). The "temperature" screen
appears first. The user can scroll to further screens
("heating / cooling," "relative humidity," and "CO2
concentration") using the left ( ) or right ( ) arrow softkey.

NOTE: The user can, at any time, exit the expanded menu

using the upper left softkey (below the " "
symbol or the word "HOME") – or by simply waiting
approx. 60 seconds.

In the expanded menu, the current temperature, relative
humidity, and CO2 concentration can be displayed.

The user can change automatic heating / cooling by
scrolling (arrow softkeys) to the "heating / cooling" screen
and then touching the upper right softkey, (below the " "
symbol or the word "EDIT"). The actual setting will then
flash at 1 Hz for approx. 7 seconds, during which time the
user can either cancel the given setting (upper left softkey,
below the " " symbol or the word "CANCEL") or confirm it
(upper right softkey, below the " " symbol or the word
"DONE"). If no action is taken within this time, the given
setting is automatically confirmed.

Fig. 179. Accessing the expanded menu

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

17 31-00281ES-01 (EN1B-0664GE51 R0819)

TROUBLESHOOTING

All units feature a Service Button, Status LED, Power LED,
and two additional LEDs (T1 and R1) for commissioning
and troubleshooting. See also Table 7 and Table 8 and
"Service Button".

Check if the Status LED's behavior is changed if you switch
the power OFF/ON. Please contact Honeywell if this does
not solve the problem.

ACCESSORIES

Terminal Protection Cover; required for wall mounting. Bulk
pack set of ten covers.

▪ For large controllers, order no.: IRM-RLC

▪ For small controllers, order no.: IRM-RSC

APPROVALS, CERTIFICATIONS,
ETC.

Approvals and Certifications

▪ UL 60730-1, Standard for Automatic Electric Controls

for Household and Similar Use, Part 1: General
Requirements;

▪ CAN/CSA-E60730-1:02, Standard for Automatic

Electrical Controls for Household and Similar Use, Part
1: General Requirements;

▪ Complementary listing for UL916, CSA C22.2 No. 205;

▪ BTL-listed, BACnet ASC profile;

▪ CE-approved;

▪ FCC part 15B-compliant: This equipment has been

tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can
radiate radio-frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and
receiver.

- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV
technician for help.

▪ RoHS Conformity.

Classification according to EN 60730-1

EN 60730 sub part: EN 60730-2-9

Environmental conditions: For use in home (residential,

commercial, and light­industrial) environments

Construction: independently mounted

control, for panel-mounting

Action: type 1.C

Rated impulse voltage: 500 V at 24 V

Pollution degree: 2

Protection against shock: Class 0 (without terminal

covers)
Class II (with terminal covers)

Software class: Class A

Classification according to EN 60529

(Degree of protection provided by enclosures)

IP20. In the case of controllers mounted outside of a
cabinet, before applying power to the device, Terminal
Protection Covers (10-pc. bulk packs, order no.: IRM-RLC
for large housings and IRM-RSC for small housings) must
be mounted so as to provide IP30.

Ambient Environmental Limits

24 VAC Models (5to90% r.H., non-condensing)

Operating temperature: 32 to 122 °F (0 to +50 °C)

Storage temperature: -4 to +158 °F (-20 to +70 °C)

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 18

RELATED TECHNICAL LITERATURE

Table 11. Related Technical Literature

Title

Product Literature no.

Spyder Model 5 – Mounting Instructions

31-00276ES

Spyder Model 5 – Product Data

31-00280ES

Spyder Model 5 – Engineering Tool User Guide

31-00282ES

TR40x/TR42x – Specification Data

63-1389

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

19 31-00281ES-01 (EN1B-0664GE51 R0819)

APPENDIX: SENSOR CHARACTERISTICS

Sensor Input Accuracy

The controller's internal sensor inputs support NTC10kΩ (Type II) and NTC20kΩ sensors. The following table lists the typical
minimum accuracies of the hardware and software for these temperature sensors.

Table 12. Accuracies of internal NTC10kΩ and NTC20kΩ sensor inputs of the controller

range

measurement error (excluding sensor characteristics)

NTC10kΩ

(A

(Type II)

NTC20kΩ

-58 to -4 °F (-50 to -20 °C)

≤ 5.0 K

≤ 5.0 K

-4 to +32 °F (-20 to 0 °C)

≤ 1.0 K

≤ 1.0 K

32 to 86 °F (0 to 30 °C)

≤ 0.5 K

≤ 0.3 K

86 to 158 °F (30 to 70 °C)

≤ 0.5 K

≤ 0.5 K

158 to 212 °F (70 to 100 °C)

≤ 1.0 K

≤ 1.0 K

212 to 266 °F (100 to 130 °C)

--

≤ 3.0 K

266 to 302 °F (130 to 150 °C)

--

≤ 5.5 K

302 to 752 °F (150 to 400 °C)

--

--

(A

NTC10kΩ (Type II) specified for -22 to 212 °F (-30 to +100 °C) only.

NOTE: This is the accuracy of the internal sensor input (hardware + software [linearization]), only. This table does not

include the characteristics of the sensors, themselves (see section “Sensor Characteristics” below). If a different
sensor or sensor accuracy is required, one may instead use the inputs of, e.g., a connected Panel I/O module.

Recognition of Sensor Failure of Sensor Inputs

The thresholds at which sensor failures – i.e., sensor breaks (SB) and short-circuits (SC) – are recognized depends upon the
given sensor type. In the event of a recognized sensor failure, the sensor input is set to "invalid." The user may program
safety functions based upon invalid sensor data. Table 13 lists the measurement ranges and the corresponding thresholds
for the recognition of sensor failure for the various different sensor types:

Table 13. Thresholds for short-circuit (SC) and sensor-break (SB) recognition

I/O configuration

measurement range

recognition thresholds

2to10 V

2to10 V / 4to20 mA (without pull-up)

SC: < 1.5 V / 3 mA; SB: no recognition

NTC10kΩ (Type II)

-58 to +212 °F (-50 to +100 °C)

SC: < 20 Ω; SB: < -94 °F (-70 °C)

NTC20kΩ

-58 to +302 °F (-50 to +150 °C)

SC: < 20 Ω; SB: < -94 °F (-70 °C)

PT1000

-22 to +752 °F (-30 to + 400 °C)

SC: < 775 Ω; SB: < -58 °F (-50 °C)

Ni1000TK5000

-94 to +266 °F (-70 to +130 °C)

SC: < 850 Ω; SB: < -58 °F (-30 °C)

NOTE: In the case of temperatures lying outside the aforementioned ranges, the lowest/highest value within the range,

instead, will be communicated. Thus, a temperature of -51 °F will be communicated as “-50 °F.”

Sensor Characteristics

The characteristics (resistance in relation to temperature) of the sensors and the resultant voltage are listed on the
following pages. The stated values do not include failures due to sensor failures; wiring resistance or wiring failures;
misreading’s due to a meter connected to measure resistance or voltage at the input.

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 20

NTC 10 kΩ (Type II)

Temp.
°F (°C)

Resistance

[kΩ]

Terminal

voltage

[V]

-22 (-30)

177

7.904

-20.2 (-29)

166.35

7.848

-18.4 (-28)

156.413

7.790

-16.6 (-27)

147.136

7.730

-14.8 (-26)

138.47

7.666

-13 (-25)

130.372

7.601

-11.2 (-24)

122.8

7.534

-9.4 (-23)

115.718

7.464

-7.6 (-22)

109.089

7.392

-5.8 (-21)

102.883

7.318

-4 (-20)

97.073

7.241

-2.2 (-19)

91.597

7.161

-0.4 (-18)

86.471

7.080

1.4 (-17)

81.667

6.996

3.2 (-16)

77.161

6.910

5 (-15)

72.932

6.821

6.8 (-14)

68.962

6.731

8.6 (-13)

65.231

6.639

10.4 (-12)

61.723

6.545

12.2 (-11)

58.424

6.448

14 (-10)

55.321

6.351

15.8 (-9)

52.399

6.251

17.6 (-8)

49.648

6.150

19.4 (-7)

47.058

6.047

21.2 (-6)

44.617

5.943

23 (-5)

42.317

5.838

24.8 (-4)

40.15

5.732

26.6 (-3)

38.106

5.624

28.4 (-2)

36.18

5.516

30.2 (-1)

34.363

5.408

32 (0)

32.65

5.299

33.8 (1)

31.027

5.189

35.6 (2)

29.494

5.079

37.4 (3)

28.047

4.969

39.2 (4)

26.68

4.859

41 (5)

25.388

4.750

42.8 (6)

24.166

4.641

44.6 (7)

23.01

4.532

46.4 (8)

21.916

4.423

48.2 (9)

20.88

4.316

50 (10)

19.898

4.209

51.8 (11)

18.968

4.103

Temp.
°F (°C)

Resistance

[kΩ]

Terminal

voltage

[V]

53.6 (12)

18.087

3.998

55.4 (13)

17.252

3.894

57.2 (14)

16.46

3.792

59 (15)

15.708

3.690

60.8 (16)

14.995

3.591

62.6 (17)

14.319

3.492

64.4 (18)

13.678

3.396

66.2 (19)

13.068

3.300

68 (20)

12.49

3.207

69.8 (21)

11.94

3.115

71.6 (22)

11.418

3.025

73.4 (23)

10.921

2.937

75.2 (24)

10.449

2.850

77 (25)

10

2.767

78.8 (26)

9.572

2.684

80.6 (27)

9.165

2.603

82.4 (28)

8.777

2.524

84.2 (29)

8.408

2.447

86 (30)

8.057

2.372

87.8 (31)

7.722

2.299

89.6 (32)

7.402

2.228

91.4 (33)

7.098

2.159

93.2 (34)

6.808

2.091

95 (35)

6.531

2.025

96.8 (36)

6.267

1.962

98.6 (37)

6.015

1.900

100.4 (38)

5.775

1.840

102.2 (39)

5.546

1.781

104 (40)

5.327

1.724

105.8 (41)

5.117

1.669

107.6 (42)

4.917

1.616

109.4 (43)

4.726

1.564

111.2 (44)

4.543

1.514

113 (45)

4.369

1.465

114.8 (46)

4.202

1.418

116.6 (47)

4.042

1.373

118.4 (48)

3.889

1.329

120.2 (49)

3.743

1.286

122 (50)

3.603

1.244

123.8 (51)

3.469

1.204

125.6 (52)

3.34

1.166

127.4 (53)

3.217

1.128

Temp.
°F (°C)

Resistance

[kΩ]

Terminal

voltage

[V]

129.2 (54)

3.099

1.092

131 (55)

2.986

1.057

132.8 (56)

2.878

1.023

134.6 (57)

2.774

0.990

136.4 (58)

2.675

0.959

138.2 (59)

2.579

0.928

140 (60)

2.488

0.898

141.8 (61)

2.4

0.870

143.6 (62)

2.316

0.842

145.4 (63)

2.235

0.815

147.2 (64)

2.158

0.790

149 (65)

2.083

0.765

150.8 (66)

2.011

0.740

152.6 (67)

1.943

0.718

154.4 (68)

1.877

0.695

156.2 (69)

1.813

0.673

158 (70)

1.752

0.652

159.8 (71)

1.694

0.632

161.6 (72)

1.637

0.612

163.4 (73)

1.583

0.593

165.2 (74)

1.531

0.575

167 (75)

1.481

0.557

168.8 (76)

1.433

0.541

170.6 (77)

1.387

0.524

172.4 (78)

1.342

0.508

174.2 (79)

1.299

0.493

176 (80)

1.258

0.478

177.8 (81)

1.218

0.464

179.6 (82)

1.179

0.450

181.4 (83)

1.142

0.436

183.2 (84)

1.107

0.423

185 (85)

1.072

0.411

186.8 (86)

1.039

0.399

188.6 (87)

1.007

0.387

190.4 (88)

0.976

0.375

192.2 (89)

0.947

0.365

194 (90)

0.918

0.354

195.8 (91)

0.89

0.344

197.6 (92)

0.863

0.334

199.4 (93)

0.838

0.324

201.2 (94)

0.813

0.315

203 (95)

0.789

0.306

Temp.
°F (°C)

Resistance

[kΩ]

Terminal

voltage

[V]

204.8 (96)

0.765

0.297

206.6 (97)

0.743

0.289

208.4 (98)

0.721

0.280

210.2 (99)

0.7

0.276

212 (100)

0.68

0.265

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

21 31-00281ES-01 (EN1B-0664GE51 R0819)

NTC 20 kΩ

Temp.
°F (°C)

Resistance

[kΩ]

Terminal

voltage

[V]

-58 (-50)

1659

8.78

-56.2 (-49)

1541

8.77

-54.4 (-48)

1432

8.76

-52.6 (-47)

1331

8.75

-50.8 (-46)

1239

8.74

-49 (-45)

1153

8.72

-47.2 (-44)

1073

8.71

-45.4 (-43)

1000

8.70

-43.6 (-42)

932

8.69

-41.8 (-41)

869

8.67

-40 (-40)

811

8.66

-38.2 (-39)

757

8.64

-36.4 (-38)

706

8.62

-34.6 (-37)

660

8.60

-32.8 (-36)

617

8.58

-31 (-35)

577

8.56

-29.2 (-34)

539

8.54

-27.4 (-33)

505

8.52

-25.6 (-32)

473

8.49

-23.8 (-31)

443

8.47

-22 (-30)

415

8.44

-20.2 (-29)

389

8.41

-18.4 (-28)

364

8.38

-16.6 (-27)

342

8.35

-14.8 (-26)

321

8.32

-13 (-25)

301

8.28

-11.2 (-24)

283

8.25

-9.4 (-23)

266

8.21

-7.6 (-22)

250

8.17

-5.8 (-21)

235

8.13

-4 (-20)

221

8.08

-2.2 (-19)

208

8.04

-0.4 (-18)

196

7.99

1.4 (-17)

184

7.94

3.2 (-16)

174

7.89

5 (-15)

164

7.83

6.8 (-14)

154

7.78

8.6 (-13)

146

7.72

10.4 (-12)

137

7.66

12.2 (-11)

130

7.60

14 (-10)

122

7.53

15.8 (-9)

116

7.46

17.6 (-8)

109

7.39

19.4 (-7)

103

7.32

21.2 (-6)

97.6

7.25

23 (-5)

92.3

7.17

24.8 (-4)

87.3

7.09

26.6 (-3)

82.6

7.01

28.4 (-2)

78.2

6.93

30.2 (-1)

74.1

6.85

32 (0)

70.2

6.76

33.8 (1)

66.5

6.67

35.6 (2)

63.0

6.58

Temp.
°F (°C)

Resistance

[kΩ]

Terminal

voltage

[V]

37.4 (3)

59.8

6.49

39.2 (4)

56.7

6.40

41 (5)

53.8

6.30

42.8 (6)

51.1

6.20

44.6 (7)

48.5

6.10

46.4 (8)

46.0

6.00

48.2 (9)

43.7

5.90

50 (10)

41.6

5.80

51.8 (11)

39.5

5.70

53.6 (12)

37.6

5.59

55.4 (13)

35.7

5.49

57.2 (14)

34.0

5.38

59 (15)

32.3

5.28

60.8 (16)

30.8

5.17

62.6 (17)

29.3

5.07

64.4 (18)

27.9

4.96

66.2 (19)

26.6

4.85

68 (20)

25.3

4.75

69.8 (21)

24.2

4.64

71.6 (22)

23.0

4.53

73.4 (23)

22.0

4.43

75.2 (24)

21.0

4.32

77 (25)

20.0

4.22

78.8 (26)

19.1

4.12

80.6 (27)

18.2

4.01

82.4 (28)

17.4

3.91

84.2 (29)

16.6

3.81

86 (30)

15.9

3.71

87.8 (31)

15.2

3.62

89.6 (32)

14.5

3.52

91.4 (33)

13.9

3.43

93.2 (34)

13.3

3.33

95 (35)

12.7

3.24

96.8 (36)

12.1

3.15

98.6 (37)

11.6

3.06

100.4 (38)

11.1

2.97

102.2 (39)

10.7

2.89

104 (40)

10.2

2.81

105.8 (41)

9.78

2.72

107.6 (42)

9.37

2.64

109.4 (43)

8.98

2.57

111.2 (44)

8.61

2.49

113 (45)

8.26

2.42

114.8 (46)

7.92

2.34

116.6 (47)

7.60

2.27

118.4 (48)

7.29

2.20

120.2 (49)

7.00

2.14

122 (50)

6.72

2.07

123.8 (51)

6.45

2.01

125.6 (52)

6.19

1.94

127.4 (53)

5.95

1.88

129.2 (54)

5.72

1.82

131 (55)

5.49

1.77

Temp.
°F (°C)

Resistance

[kΩ]

Terminal

voltage

[V]

132.8 (56)

5.28

1.71

134.6 (57)

5.08

1.66

136.4 (58)

4.88

1.61

138.2 (59)

4.69

1.56

140 (60)

4.52

1.51

141.8 (61)

4.35

1.46

143.6 (62)

4.18

1.41

145.4 (63)

4.03

1.37

147.2 (64)

3.88

1.32

149 (65)

3.73

1.28

150.8 (66)

3.59

1.24

152.6 (67)

3.46

1.20

154.4 (68)

3.34

1.16

156.2 (69)

3.21

1.13

158 (70)

3.10

1.09

159.8 (71)

2.99

1.06

161.6 (72)

2.88

1.02

163.4 (73)

2.78

0.991

165.2 (74)

2.68

0.960

167 (75)

2.58

0.929

168.8 (76)

2.49

0.900

170.6 (77)

2.41

0.872

172.4 (78)

2.32

0.844

174.2 (79)

2.24

0.818

176 (80)

2.17

0.792

177.8 (81)

2.09

0.767

179.6 (82)

2.02

0.744

181.4 (83)

1.95

0.720

183.2 (84)

1.89

0.698

185 (85)

1.82

0.676

186.8 (86)

1.76

0.655

188.6 (87)

1.70

0.635

190.4 (88)

1.65

0.616

192.2 (89)

1.59

0.597

194 (90)

1.54

0.578

195.8 (91)

1.49

0.561

197.6 (92)

1.44

0.544

199.4 (93)

1.40

0.527

201.2 (94)

1.35

0.511

203 (95)

1.31

0.496

204.8 (96)

1.27

0.481

206.6 (97)

1.23

0.466

208.4 (98)

1.19

0.452

210.2 (99)

1.15

0.439

212 (100)

1.11

0.425

213.8 (101)

1.08

0.413

215.6 (102)

1.05

0.401

217.4 (103)

1.01

0.389

219.2 (104)

0.98

0.378

221 (105)

0.95

0.367

222.8 (106)

0.92

0.356

224.6 (107)

0.90

0.346

226.4 (108)

0.87

0.336

Temp.
°F (°C)

Resistance

[kΩ]

Terminal

voltage

[V]

228.2 (109)

0.84

0.326

230 (110)

0.82

0.317

231.8 (111)

0.79

0.308

233.6 (112)

0.77

0.299

235.4 (113)

0.75

0.290

237.2 (114)

0.73

0.282

239 (115)

0.70

0.274

240.8 (116)

0.68

0.266

242.6 (117)

0.66

0.259

244.4 (118)

0.64

0.252

246.2 (119)

0.63

0.245

248 (120)

0.61

0.238

249.8 (121)

0.59

0.231

251.6 (122)

0.57

0.225

253.4 (123)

0.56

0.219

255.2 (124)

0.54

0.213

257 (125)

0.53

0.207

258.8 (126)

0.51

0.201

260.6 (127)

0.50

0.196

262.4 (128)

0.49

0.191

264.2 (129)

0.47

0.186

266 (130)

0.46

0.181

267.8 (131)

0.45

0.176

269.6 (132)

0.43

0.171

271.4 (133)

0.42

0.167

273.2 (134)

0.41

0.162

275 (135)

0.40

0.158

276.8 (136)

0.39

0.154

278.6 (137)

0.38

0.150

280.4 (138)

0.37

0.146

282.2 (139)

0.36

0.142

284 (140)

0.35

0.139

285.8 (141)

0.34

0.135

287.6 (142)

0.33

0.132

289.4 (143)

0.32

0.128

291.2 (144)

0.32

0.125

293 (145)

0.31

0.122

294.8 (146)

0.30

0.119

296.6 (147)

0.29

0.116

298.4 (148)

0.29

0.113

300.2 (149)

0.28

0.110

302 (150)

0.27

0.107

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 22

PT 1000

Temp.

°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

-58 (-50)

803

0.312

-56.2 (-49)

807

0.314

-54.4 (-48)

811

0.315

-52.6 (-47)

815

0.317

-50.8 (-46)

819

0.318

-49 (-45)

823

0.320

-47.2 (-44)

827

0.321

-45.4 (-43)

831

0.323

-43.6 (-42)

835

0.324

-41.8 (-41)

839

0.326

-40 (-40)

843

0.327

-38.2 (-39)

847

0.329

-36.4 (-38)

851

0.330

-34.6 (-37)

855

0.332

-32.8 (-36)

859

0.333

-31 (-35)

862

0.335

-29.2 (-34)

866

0.336

-27.4 (-33)

870

0.338

-25.6 (-32)

874

0.339

-23.8 (-31)

878

0.341

-22 (-30)

882

0.342

-20.2 (-29)

886

0.344

-18.4 (-28)

890

0.345

-16.6 (-27)

894

0.347

-14.8 (-26)

898

0.348

-13 (-25)

902

0.350

-11.2 (-24)

906

0.351

-9.4 (-23)

910

0.353

-7.6 (-22)

914

0.354

-5.8 (-21)

918

0.356

-4 (-20)

922

0.357

-2.2 (-19)

926

0.359

-0.4 (-18)

929

0.360

1.4 (-17)

933

0.361

3.2 (-16)

937

0.363

5 (-15)

941

0.364

6.8 (-14)

945

0.366

8.6 (-13)

949

0.367

10.4 (-12)

953

0.369

12.2 (-11)

957

0.370

14 (-10)

961

0.372

15.8 (-9)

965

0.373

17.6 (-8)

969

0.375

19.4 (-7)

973

0.376

21.2 (-6)

977

0.378

23 (-5)

980

0.379

24.8 (-4)

984

0.380

26.6 (-3)

988

0.382

28.4 (-2)

992

0.383

30.2 (-1)

996

0.385

32 (0)

1000

0.386

33.8 (1)

1004

0.388

35.6 (2)

1008

0.389

37.4 (3)

1012

0.391

39.2 (4)

1016

0.392

41 (5)

1020

0.394

42.8 (6)

1023

0.395

44.6 (7)

1027

0.396

46.4 (8)

1031

0.398

48.2 (9)

1035

0.399

Temp.

°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

50 (10)

1039

0.401

51.8 (11)

1043

0.402

53.6 (12)

1047

0.404

55.4 (13)

1051

0.405

57.2 (14)

1055

0.406

59 (15)

1058

0.408

60.8 (16)

1062

0.409

62.6 (17)

1066

0.411

64.4 (18)

1070

0.412

66.2 (19)

1074

0.413

68 (20)

1078

0.415

69.8 (21)

1082

0.416

71.6 (22)

1086

0.418

73.4 (23)

1090

0.419

75.2 (24)

1093

0.420

77 (25)

1097

0.422

78.8 (26)

1101

0.423

80.6 (27)

1105

0.425

82.4 (28)

1109

0.426

84.2 (29)

1113

0.428

86 (30)

1117

0.429

87.8 (31)

1121

0.431

89.6 (32)

1124

0.432

91.4 (33)

1128

0.433

93.2 (34)

1132

0.435

95 (35)

1136

0.436

96.8 (36)

1140

0.438

98.6 (37)

1144

0.439

100.4 (38)

1148

0.441

102.2 (39)

1152

0.442

104 (40)

1155

0.443

105.8 (41)

1159

0.445

107.6 (42)

1163

0.446

109.4 (43)

1167

0.448

111.2 (44)

1171

0.449

113 (45)

1175

0.451

114.8 (46)

1179

0.452

116.6 (47)

1182

0.453

118.4 (48)

1186

0.455

120.2 (49)

1190

0.456

122 (50)

1194

0.458

123.8 (51)

1198

0.459

125.6 (52)

1202

0.461

127.4 (53)

1205

0.462

129.2 (54)

1209

0.463

131 (55)

1213

0.465

132.8 (56)

1217

0.466

134.6 (57)

1221

0.467

136.4 (58)

1225

0.469

138.2 (59)

1229

0.470

140 (60)

1232

0.471

141.8 (61)

1236

0.473

143.6 (62)

1240

0.474

145.4 (63)

1244

0.476

147.2 (64)

1248

0.477

149 (65)

1252

0.479

150.8 (66)

1255

0.480

152.6 (67)

1259

0.481

154.4 (68)

1263

0.483

156.2 (69)

1267

0.484

Temp.

°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

158 (70)

1271

0.486

159.8 (71)

1275

0.487

161.6 (72)

1278

0.488

163.4 (73)

1282

0.490

165.2 (74)

1286

0.491

167 (75)

1290

0.493

168.8 (76)

1294

0.494

170.6 (77)

1297

0.495

172.4 (78)

1301

0.497

174.2 (79)

1305

0.498

176 (80)

1309

0.499

177.8 (81)

1313

0.501

179.6 (82)

1317

0.502

181.4 (83)

1320

0.503

183.2 (84)

1324

0.505

185 (85)

1328

0.506

186.8 (86)

1332

0.508

188.6 (87)

1336

0.509

190.4 (88)

1339

0.510

192.2 (89)

1343

0.512

194 (90)

1347

0.513

195.8 (91)

1351

0.515

197.6 (92)

1355

0.516

199.4 (93)

1358

0.517

201.2 (94)

1362

0.519

203 (95)

1366

0.520

204.8 (96)

1370

0.522

206.6 (97)

1374

0.523

208.4 (98)

1377

0.524

210.2 (99)

1381

0.525

212 (100)

1385

0.527

213.8 (101)

1389

0.528

215.6 (102)

1393

0.530

217.4 (103)

1396

0.531

219.2 (104)

1400

0.532

221 (105)

1404

0.534

222.8 (106)

1408

0.535

224.6 (107)

1412

0.537

226.4 (108)

1415

0.538

228.2 (109)

1419

0.539

230 (110)

1423

0.541

231.8 (111)

1427

0.542

233.6 (112)

1430

0.543

235.4 (113)

1434

0.545

237.2 (114)

1438

0.546

239 (115)

1442

0.547

240.8 (116)

1446

0.549

242.6 (117)

1449

0.550

244.4 (118)

1453

0.551

246.2 (119)

1457

0.553

248 (120)

1461

0.554

249.8 (121)

1464

0.555

251.6 (122)

1468

0.557

253.4 (123)

1472

0.558

255.2 (124)

1476

0.560

257 (125)

1479

0.561

258.8 (126)

1483

0.562

260.6 (127)

1487

0.564

262.4 (128)

1491

0.565

264.2 (129)

1494

0.566

Temp.

°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

266 (130)

1498

0.567

267.8 (131)

1502

0.569

269.6 (132)

1506

0.570

271.4 (133)

1510

0.572

273.2 (134)

1513

0.573

275 (135)

1517

0.574

276.8 (136)

1521

0.576

278.6 (137)

1525

0.577

280.4 (138)

1528

0.578

282.2 (139)

1532

0.580

284 (140)

1536

0.581

285.8 (141)

1539

0.582

287.6 (142)

1543

0.584

289.4 (143)

1547

0.585

291.2 (144)

1551

0.586

293 (145)

1554

0.587

294.8 (146)

1558

0.589

296.6 (147)

1562

0.590

298.4 (148)

1566

0.592

300.2 (149)

1569

0.593

302 (150)

1573

0.594

303.8 (151)

1577

0.596

305.6 (152)

1581

0.597

307.4 (153)

1584

0.598

309.2 (154)

1588

0.600

311 (155)

1592

0.601

312.8 (156)

1596

0.602

314.6 (157)

1599

0.603

316.4 (158)

1603

0.605

318.2 (159)

1607

0.606

320 (160)

1610

0.607

321.8 (161)

1614

0.609

323.6 (162)

1618

0.610

325.4 (163)

1622

0.612

327.2 (164)

1625

0.613

329 (165)

1629

0.614

330.8 (166)

1633

0.615

332.6 (167)

1636

0.617

334.4 (168)

1640

0.618

336.2 (169)

1644

0.619

338 (170)

1648

0.621

339.8 (171)

1651

0.622

341.6 (172)

1655

0.623

343.4 (173)

1659

0.625

345.2 (174)

1662

0.626

347 (175)

1666

0.627

348.8 (176)

1670

0.629

350.6 (177)

1674

0.630

352.4 (178)

1677

0.631

354.2 (179)

1681

0.632

356 (180)

1685

0.634

357.8 (181)

1688

0.635

359.6 (182)

1692

0.636

361.4 (183)

1696

0.638

363.2 (184)

1699

0.639

365 (185)

1703

0.640

366.8 (186)

1707

0.642

368.6 (187)

1711

0.643

370.4 (188)

1714

0.644

372.2 (189)

1718

0.645

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

23 31-00281ES-01 (EN1B-0664GE51 R0819)

Temp.

°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

374 (190)

1722

0.647

375.8 (191)

1725

0.648

377.6 (192)

1729

0.649

379.4 (193)

1733

0.651

381.2 (194)

1736

0.652

383 (195)

1740

0.653

384.8 (196)

1744

0.655

386.6 (197)

1747

0.656

388.4 (198)

1751

0.657

390.2 (199)

1755

0.658

392 (200)

1758

0.659

393.8 (201)

1762

0.661

395.6 (202)

1766

0.662

397.4 (203)

1769

0.663

399.2 (204)

1773

0.665

401 (205)

1777

0.666

402.8 (206)

1780

0.667

404.6 (207)

1784

0.669

406.4 (208)

1788

0.670

408.2 (209)

1791

0.671

410 (210)

1795

0.672

411.8 (211)

1799

0.674

413.6 (212)

1802

0.675

415.4 (213)

1806

0.676

417.2 (214)

1810

0.678

419 (215)

1813

0.679

420.8 (216)

1817

0.680

422.6 (217)

1821

0.681

424.4 (218)

1824

0.683

426.2 (219)

1828

0.684

428 (220)

1832

0.685

429.8 (221)

1835

0.686

431.6 (222)

1839

0.688

433.4 (223)

1843

0.689

435.2 (224)

1846

0.690

437 (225)

1850

0.692

438.8 (226)

1854

0.693

440.6 (227)

1857

0.694

442.4 (228)

1861

0.695

444.2 (229)

1865

0.697

446 (230)

1868

0.698

447.8 (231)

1872

0.699

449.6 (232)

1875

0.700

451.4 (233)

1879

0.702

453.2 (234)

1883

0.703

455 (235)

1886

0.704

456.8 (236)

1890

0.705

458.6 (237)

1894

0.707

460.4 (238)

1897

0.708

462.2 (239)

1901

0.709

464 (240)

1905

0.711

465.8 (241)

1908

0.712

467.6 (242)

1912

0.713

469.4 (243)

1915

0.714

471.2 (244)

1919

0.716

473 (245)

1923

0.717

474.8 (246)

1926

0.718

476.6 (247)

1930

0.719

478.4 (248)

1934

0.721

480.2 (249)

1937

0.722

482 (250)

1941

0.723

483.8 (251)

1944

0.724

485.6 (252)

1948

0.726

Temp.

°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

487.4 (253)

1952

0.727

489.2 (254)

1955

0.728

491 (255)

1959

0.729

492.8 (256)

1962

0.730

494.6 (257)

1966

0.732

496.4 (258)

1970

0.733

498.2 (259)

1973

0.734

500 (260)

1977

0.736

501.8 (261)

1980

0.737

503.6 (262)

1984

0.738

505.4 (263)

1988

0.739

507.2 (264)

1991

0.740

509 (265)

1995

0.742

510.8 (266)

1998

0.743

512.6 (267)

2002

0.744

514.4 (268)

2006

0.746

516.2 (269)

2009

0.747

518 (270)

2013

0.748

519.8 (271)

2016

0.749

521.6 (272)

2020

0.750

523.4 (273)

2024

0.752

525.2 (274)

2027

0.753

527 (275)

2031

0.754

528.8 (276)

2034

0.755

530.6 (277)

2038

0.757

532.4 (278)

2042

0.758

534.2 (279)

2045

0.759

536 (280)

2049

0.760

537.8 (281)

2052

0.761

539.6 (282)

2056

0.763

541.4 (283)

2060

0.764

543.2 (284)

2063

0.765

545 (285)

2067

0.766

546.8 (286)

2070

0.768

548.6 (287)

2074

0.769

550.4 (288)

2077

0.770

552.2 (289)

2081

0.771

554 (290)

2085

0.773

555.8 (291)

2088

0.774

557.6 (292)

2092

0.775

559.4 (293)

2095

0.776

561.2 (294)

2099

0.777

563 (295)

2102

0.778

564.8 (296)

2106

0.780

566.6 (297)

2110

0.781

568.4 (298)

2113

0.782

570.2 (299)

2117

0.784

572 (300)

2120

0.785

573.8 (301)

2124

0.786

575.6 (302)

2127

0.787

577.4 (303)

2131

0.788

579.2 (304)

2134

0.789

581 (305)

2138

0.791

582.8 (306)

2142

0.792

584.6 (307)

2145

0.793

586.4 (308)

2149

0.794

588.2 (309)

2152

0.796

590 (310)

2156

0.797

591.8 (311)

2159

0.798

593.6 (312)

2163

0.799

595.4 (313)

2166

0.800

597.2 (314)

2170

0.802

599 (315)

2173

0.803

Temp.

°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

600.8 (316)

2177

0.804

602.6 (317)

2181

0.805

604.4 (318)

2184

0.806

606.2 (319)

2188

0.808

608 (320)

2191

0.809

609.8 (321)

2195

0.810

611.6 (322)

2198

0.811

613.4 (323)

2202

0.812

615.2 (324)

2205

0.814

617 (325)

2209

0.815

618.8 (326)

2212

0.816

620.6 (327)

2216

0.817

622.4 (328)

2219

0.818

624.2 (329)

2223

0.820

626 (330)

2226

0.821

627.8 (331)

2230

0.822

629.6 (332)

2234

0.823

631.4 (333)

2237

0.824

633.2 (334)

2241

0.826

635 (335)

2244

0.827

636.8 (336)

2248

0.828

638.6 (337)

2251

0.829

640.4 (338)

2255

0.830

642.2 (339)

2258

0.831

644 (340)

2262

0.833

645.8 (341)

2265

0.834

647.6 (342)

2269

0.835

649.4 (343)

2272

0.836

651.2 (344)

2276

0.838

653 (345)

2279

0.839

654.8 (346)

2283

0.840

656.6 (347)

2286

0.841

658.4 (348)

2290

0.842

660.2 (349)

2293

0.843

662 (350)

2297

0.845

663.8 (351)

2300

0.846

665.6 (352)

2304

0.847

667.4 (353)

2307

0.848

669.2 (354)

2311

0.849

671 (355)

2314

0.850

672.8 (356)

2318

0.852

674.6 (357)

2321

0.853

676.4 (358)

2325

0.854

678.2 (359)

2328

0.855

680 (360)

2332

0.856

681.8 (361)

2335

0.857

683.6 (362)

2339

0.859

685.4 (363)

2342

0.860

687.2 (364)

2346

0.861

689 (365)

2349

0.862

690.8 (366)

2353

0.863

692.6 (367)

2356

0.864

694.4 (368)

2360

0.866

696.2 (369)

2363

0.867

698 (370)

2367

0.868

699.8 (371)

2370

0.869

701.6 (372)

2373

0.870

703.4 (373)

2377

0.871

705.2 (374)

2380

0.872

707 (375)

2384

0.874

708.8 (376)

2387

0.875

710.6 (377)

2391

0.876

712.4 (378)

2394

0.877

Temp.

°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

714.2 (379)

2398

0.878

716 (380)

2401

0.879

717.8 (381)

2405

0.881

719.6 (382)

2408

0.882

721.4 (383)

2412

0.883

723.2 (384)

2415

0.884

725 (385)

2419

0.885

726.8 (386)

2422

0.886

728.6 (387)

2426

0.888

730.4 (388)

2429

0.889

732.2 (389)

2432

0.890

734 (390)

2436

0.891

735.8 (391)

2439

0.892

737.6 (392)

2443

0.893

739.4 (393)

2446

0.894

741.2 (394)

2450

0.896

743 (395)

2453

0.897

744.8 (396)

2457

0.898

746.6 (397)

2460

0.899

748.4 (398)

2463

0.900

750.2 (399)

2467

0.901

752 (400)

2470

0.902

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

31-00281ES-01 (EN1B-0664GE51 R0819) 24

NI1000TK5000

Temp.
°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

-22 (-30)

871.7

0.338

-20.2 (-29)

875.8

0.340

-18.4 (-28)

880

0.341

-16.6 (-27)

884.1

0.343

-14.8 (-26)

888.3

0.344

-13 (-25)

892.5

0.346

-11.2 (-24)

896.7

0.348

-9.4 (-23)

900.8

0.349

-7.6 (-22)

905.1

0.351

-5.8 (-21)

909.3

0.352

-4 (-20)

913.5

0.354

-2.2 (-19)

917.7

0.355

-0.4 (-18)

922

0.357

1.4 (-17)

926.2

0.359

3.2 (-16)

930.5

0.360

5 (-15)

934.7

0.362

6.8 (-14)

939

0.363

8.6 (-13)

943.3

0.365

10.4 (-12)

947.6

0.367

12.2 (-11)

951.9

0.368

14 (-10)

956.2

0.370

15.8 (-9)

960.6

0.371

17.6 (-8)

964.9

0.373

19.4 (-7)

969.3

0.375

21.2 (-6)

973.6

0.376

23 (-5)

978

0.378

24.8 (-4)

982.4

0.380

26.6 (-3)

986.7

0.381

28.4 (-2)

991.2

0.383

30.2 (-1)

995.6

0.384

32 (0)

1000

0.386

33.8 (1)

1004.4

0.388

35.6 (2)

1008.9

0.389

37.4 (3)

1013.3

0.391

39.2 (4)

1017.8

0.393

41 (5)

1022.3

0.394

42.8 (6)

1026.7

0.396

44.6 (7)

1031.2

0.398

46.4 (8)

1035.8

0.399

48.2 (9)

1040.3

0.401

50 (10)

1044.8

0.403

51.8 (11)

1049.3

0.404

53.6 (12)

1053.9

0.406

55.4 (13)

1058.4

0.408

57.2 (14)

1063

0.409

59 (15)

1067.6

0.411

60.8 (16)

1072.2

0.413

62.6 (17)

1076.8

0.415

Temp.
°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

64.4 (18)

1081.4

0.416

66.2 (19)

1086

0.418

68 (20)

1090.7

0.420

69.8 (21)

1095.3

0.421

71.6 (22)

1100

0.423

73.4 (23)

1104.6

0.425

75.2 (24)

1109.3

0.427

77 (25)

1114

0.428

78.8 (26)

1118.7

0.430

80.6 (27)

1123.4

0.432

82.4 (28)

1128.1

0.433

84.2 (29)

1132.9

0.435

86 (30)

1137.6

0.437

87.8 (31)

1142.4

0.439

89.6 (32)

1147.1

0.440

91.4 (33)

1151.9

0.442

93.2 (34)

1156.7

0.444

95 (35)

1161.5

0.446

96.8 (36)

1166.3

0.447

98.6 (37)

1171.2

0.449

100.4 (38)

1176

0.451

102.2 (39)

1180.9

0.453

104 (40)

1185.7

0.455

105.8 (41)

1190.6

0.456

107.6 (42)

1195.5

0.458

109.4 (43)

1200.4

0.460

111.2 (44)

1205.3

0.462

113 (45)

1210.2

0.463

114.8 (46)

1215.1

0.465

116.6 (47)

1220.1

0.467

118.4 (48)

1225

0.469

120.2 (49)

1230

0.471

122 (50)

1235

0.473

123.8 (51)

1240

0.474

125.6 (52)

1245

0.476

127.4 (53)

1250

0.478

129.2 (54)

1255

0.480

131 (55)

1260.1

0.482

132.8 (56)

1265.1

0.484

134.6 (57)

1270.2

0.485

136.4 (58)

1275.3

0.487

138.2 (59)

1280.3

0.489

140 (60)

1285.4

0.491

141.8 (61)

1290.6

0.493

143.6 (62)

1295.7

0.495

145.4 (63)

1300.8

0.496

147.2 (64)

1306

0.498

149 (65)

1311.1

0.500

Temp.
°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

150.8 (66)

1316.3

0.502

152.6 (67)

1321.5

0.504

154.4 (68)

1326.7

0.506

156.2 (69)

1331.9

0.508

158 (70)

1337.1

0.510

159.8 (71)

1342.4

0.512

161.6 (72)

1347.6

0.513

163.4 (73)

1352.9

0.515

165.2 (74)

1358.2

0.517

167 (75)

1363.5

0.519

168.8 (76)

1368.8

0.521

170.6 (77)

1374.1

0.523

172.4 (78)

1379.4

0.525

174.2 (79)

1384.8

0.527

176 (80)

1390.1

0.529

177.8 (81)

1395.5

0.531

179.6 (82)

1400.9

0.533

181.4 (83)

1406.3

0.535

183.2 (84)

1411.7

0.537

185 (85)

1417.1

0.538

186.8 (86)

1422.5

0.540

188.6 (87)

1428

0.542

190.4 (88)

1433.4

0.544

192.2 (89)

1438.9

0.546

194 (90)

1444.4

0.548

195.8 (91)

1449.9

0.550

197.6 (92)

1455.4

0.552

199.4 (93)

1460.9

0.554

201.2 (94)

1466.5

0.556

203 (95)

1472

0.558

204.8 (96)

1477.6

0.560

206.6 (97)

1483.2

0.562

208.4 (98)

1488.8

0.564

210.2 (99)

1494.4

0.566

212 (100)

1500

0.568

213.8 (101)

1505.6

0.570

215.6 (102)

1511.3

0.572

217.4 (103)

1517

0.574

219.2 (104)

1522.6

0.576

221 (105)

1528.3

0.578

222.8 (106)

1534

0.580

224.6 (107)

1539.7

0.582

226.4 (108)

1545.5

0.584

228.2 (109)

1551.2

0.586

230 (110)

1557

0.589

231.8 (111)

1562.8

0.591

233.6 (112)

1568.5

0.593

235.4 (113)

1574.4

0.595

Temp.
°F (°C)

Resistance

[Ω]

Terminal

voltage [V]

237.2 (114)

1580.2

0.597

239 (115)

1586

0.599

240.8 (116)

1591.8

0.601

242.6 (117)

1597.7

0.603

244.4 (118)

1603.6

0.605

246.2 (119)

1609.5

0.607

248 (120)

1615.4

0.609

249.8 (121)

1621.3

0.611

251.6 (122)

1627.2

0.613

253.4 (123)

1633.2

0.616

255.2 (124)

1639.1

0.618

257 (125)

1645.1

0.620

258.8 (126)

1651.1

0.622

260.6 (127)

1657.1

0.624

262.4 (128)

1663.1

0.626

264.2 (129)

1669.1

0.628

266 (130)

1675.2

0.630

SPYDER MODEL 5 ROOM CONTROLLERS − INSTALLATION GUIDE

Manufactured for and on behalf of the BMS Division of Honeywell Products and Solutions SARL, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized
Representative:

Honeywell Building Technologies

Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
customer.honeywell.com

© 2019 Honeywell International Inc.

31-00281ES-01 (EN1B-0664GE51 R0819) | Rev. 01 08-19

Trademark Information

BACnetTM is a trademark of ASHRAE Inc.