Honeywell PC-503 User Manual
Parameter
PC503
RF Data Rate
250kbps
Antenna Type
SMT
Indoor Range
70ft
Transmit Power
3mW (+5dBm)
Receive Sensitivity
-95dBm
Frequency Band
2.4Ghz
Encryption
AES-128
Protocol
802.15.4
Frequency Channels
11-26
Input Voltage
5VDC (USB)
Operating Ambient Temperature
0°C–40 °C
LEDS
Flashes to show Transmit and Receive RF
Frames.
PC-503 User Manual
Overview
PC-503 is a commissioning tool designed to work with INNTOOL/EngINN application. PC-503 comes with a USB to Mini
USB cable. USB cable provides power and communication interface to a laptop or personal computer. The device has
two LEDs which blinks to show transmit (Tx) and receive (Rx) communication with laptop.
Important Note: PC-503 will not work with the INNCOM SNEEZER or any other INNCOM legacy tool. PC-503 is an RF-only
device and does not provide either S5 or IR5 interface.
Specification:
Honeywell Internal
Agency:
Standard
CE
EN 300 328 V2.1.1:Ed 2016
CE
EN 301 489-1 V2.1.1/V2.2.0
CE
EN 301 489-17 V3.1.1/V3.2.0
CE
EN55032:2012/AC:2013 Class B
CE
EN 55024:2010
CE
EN 61000-3-2:2014
CE
EN 61000-3-3:2013
FCC
FCC 47 CFR Part 15:2017, Sections 15.107 and 15.109 Class B
FCC
FCC 47 CFR Part 15.249:2017
IC
IC ICES-003, Issue 6:2016, Class B
IC
RSS-210, Issue 9, 2016
IC
RSS-Gen, Issue 4, 2014
OS Number
201-503
Compliance:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by INNCOM and Honeywell International Inc. can void the user’s
authority to operate this device.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
Cet appareil est conforme à la norme RSS Industrie Canada exempt de licence. Son fonctionnement est soumis aux deux
conditions suivantes:
(1) cet appareil ne doit pas provoquer d’interférences et
(2) cet appareil doit accepter toute interférence, y compris les interferences pouvant causer un mauvais fonctionnement
du dispositif.
Honeywell Internal
Loading...