Honeywell MO08CESWS, MO08CESWK, MO08CESWB, MO10CESWS, MO10CESWK User manual

...

Portable Air Conditioner User Manual

Read and save these instructions before use

Climatiseur portatif Mode d’emploi

Lire ces consignes avant l’utilisation de l’appareil et les conserver

Aire Acondicionado Portátil Manual Del Propietario

Lea y guarde estas instrucciones antes de usar la unidad

Model / Modèle / Modelo:

MO08CESWS, MO08CESWK, MO08CESWB

MO10CESWS, MO10CESWK, MO10CESWB

Customer Support: Assistance Au Client: Servicio de atencion a clientes: USA/ EE.UU: 18004742147 CANADA/ CANADÁ^ : 18882090999

^ Canada Customer Support service available for models sold in Canada only. ^ Le Service Client Canadien est disponible uniquement pour les modèles vendus sur le territoire Canadien. ^ Servicio de Atención A Clientes en Canadá disponible solo para modelos vendidos en Canadá.

www.jmatek.com Email: usinfo@jmatek.com

MO08 Series / Série / Serie:

MO10 Series / Série / Serie:

SAFETY

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS. READ CAREFULLY AND KEEP FOR FUTURE REFERENCE. IN CASE THERE IS ANY INCONSISTENCY OR CONFLICT BETWEEN THE ENGLISH VERSION AND ANY OTHER LANGUAGE VERSION OF THE CONTENT OF THIS MATERIAL, THE ENGLISH VERSION SHALL PREVAIL.

WARNING:

DO NOT operate the unit with a damaged plug or loose wall outlet. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualiﬁed persons in order to avoid a hazard.

DO NOT cover the air intake and exhaust when in use.

DO NOT place objects on or sit on the unit.

Always turn off and unplug the unit when cleaning or servicing.

DO NOT use the appliance if it is damaged.

If service is needed contact an authorized service agent.

Unplug the unit when stored or not in use.

DO NOT pull or carry the appliance by the power cord.

DO NOT pinch the wire in the door and DO NOT pull it along edges or sharp corners.

DO NOT run the power cord under carpeting and rugs.

Use caution to prevent tripping on cord.

DO NOT use the device in the following cases:

- Near a ﬁre source

- In areas where gasoline, paint or other ﬂammable goods are stored

- In an area where the water can be projected

DO NOT touch the plug or the device with wet hands.

Basic safety precautions should always be followed when using electrical appliances.

SAFETY (CONTINUED)

This appliance has been manufactured for use in domestic environments and should not be used for other purposes. Only use the installation kit provided to install this unit. DO NOT attempt to extend the exhaust hose or install this unit using other methods other than that shown in this manual. Improper installation will void any existing warranties. DO NOT use an extension cord with this unit. This appliance can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Never insert your ﬁngers or rods into the air outlet. Take special care to warn children of these dangers. The manufacturer is not liable for injury caused to persons or property damage due to non-compliance with maintenance instructions and improper use of the appliance. The appliance shall be installed in accordance with national wiring regulations. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Children should be supervised to ensure that they do not play with the appliance.

THANK YOU

Congratulations on your purchase of this Honeywell Portable Air Conditioner.

Regarding the information pertaining to the installation, handling, servicing, cleaning and disposal of the appliance, please refer to the below paragraph of the manual.

USER TIPS

Portable Air Conditioners are ideal for spot cooling. The compressor, condenser and evaporator are housed in a compact unit. The air is dehumidiﬁed and cooled while a ﬂexible exhaust hose sends heat outside. The air conditioner includes a window venting kit. No permanent installation is needed. The unit is easy to move from room to room and offers a truly ﬂexible air conditioning solution.

Auto Evaporation System - The unit automatically evaporates the condensate through the exhaust hose. There is no need to empty the drainage tank except in very humid conditions. Read and follow the instructions carefully.

To ensure optimal efﬁciency of the product, keep doors and windows closed when it is used as an air conditioner or dehumidiﬁer. If the product is being used with the fan function only, an open window could improve air circulation.

Cooling and Dehumidifying Operation Fan Operation

Important:

Before installing the unit, place it UPRIGHT for 1 hour before use to allow the refrigerant to stabilize. Manually adjust the air vent located at the top of the unit to adjust the direction of air ﬂow.

Follow installation instructions to set up the unit.

Plug the unit into a properly grounded circuit. DO NOT plug into an extension cord.

PARTS DESCRIPTION

1) Control Panel (Incl. Signal Receptor)

2) Air Outlet 8) Power Supply Cord

3) Handle 9) Remote Control

4) Casters 10) Lower Rubber Drain Plug

5) Dust Filter 11) Upper Rubber Drain Plug

6) Back Grill

7) Exhaust Hose Connector

(Air Conditioning Mode)

(Dehumidiﬁer Mode)

INSTALLATION

It is important that the installation instructions below are followed for successful installation of this Portable Air Conditioner. Please call Customer Support if you have any difﬁculties or queries regarding these installation procedures.

1 3

Installation Kit:

1. Window Bracket Kit (1 Set) 4. Hole Cover (1 Piece)

2. Window Bracket Panel Adapter (1 Piece) 5. Exhaust Hose (1 Piece)

3. Exhaust Hose Connector (1 Piece)

Installation Steps:

Install the exhaust hose with window bracket adapter and exhaust hose connector on both sides.

1. Ensure proper ﬁt on both ends.

x1 x1

2. The Window Brackets are approximatley 50 cm / 19.7 inches each, allowing you to install to windows and balcony doors of different heights or width.

19.7" 50cm 1 part

50cm / 19.7" to 97cm / 38.2" 2 parts

Adjustable Knobs

3EN

1.2m / 47.2" 3 parts

INSTALLATION (CONTINUED)

Note: After setting the window bracket to the size of your window, please remove it from the window and follow the instructions below.

3. Connect the exhaust hose to the exhaust hose connector on back of the unit. Slide-in the exhaust hose connector. Press the button to lock the exhaust hose connector in place.

Exhaust Hose: Dia. 5.5" (14cm) Length: 12" to 47" (30cm to 120cm)

4. Connect the window bracket to the window bracket panel adapter. Ensure that all connections are tight and installed properly.

5. Connect the window bracket to the window.

The Portable Air Conditioner is now ready to use.

4EN

INSTALLATION (CONTINUED)

Important:

Do not replace or lengthen the exhaust hose as this could cause the unit to malfunction.

50 cm / 20"

MAX. 36 cm / 14"

MAX. 102 cm / 40"

NOT RECOMMENDED RECOMMENDED

WARNING: Any warranties included with this product will be voided if an extra extension hose is

added to the originally provided installation kit or if the installation is performed differently than the manufacturer's instructions, without proper consultation. Please contact Customer Support for help with installation procedures if needed.

The supplied exhaust hose has a diameter of 5.5 inches (14 cm) and can be extended from 12 inches to 47 inches (30 cm to 120 cm).

Do not bend (to the extent shown below) the exhaust hose. A bent hose will block exhaust air and cause the unit to malfunction or shut-off. Make sure the back of the unit is at least 50 cm / 20 inches away from the wall. Do not place the

unit in front of curtains or drapes as this could obstruct the airﬂow.

USE & OPERATION

CONTROL PANEL

(6) (7)

(5) (1)

1) Timer Control 4) Mode Control 7) Timer Light

2) Fan Speed Control 5) Power Control / Standby Mode 8) Filter Alert

3) Timer / Temperature Set Controls 6) Warning Light (when ﬂashing)

FUNCTION BUTTONS

POWER CONTROL

The Power Control turns the unit on and off. When the unit is plugged in, this button lights up indicating it is in a Standby Mode ready to be switched on anytime.

TIMER CONTROL

While the unit is turned on, press the timer button then press the + or - to select the number of hours you would like the unit to continue to run. The unit will turn off automatically.

AUTO TURN OFF:

While unit is running, press the button and the display will ﬂash. While the display is ﬂashing, press the + or - button to select the number of hours you want the unit to turn OFF automatically.

(4) (2) (3) (8)

AUTO TURN ON:

When unit is in a standby mode (plugged in with power light on), then press the + or - button to select the number of hours until you want the unit to automatically start running.

TEMPERATURE / TIMER SET CONTROLS

Used for adjusting the timer and thermostat.

The default display is setting temperature.

In cooling mode, when + or - button is pressed, the set temperature is displayed and may be adjusted. After 10 seconds the display will revert back to room temperature. Temperature is only adjustable in cool mode. The time is adjustable between 1 - 24 hours. Note: By pressing both + or - buttons at the same time, the display will toggle between Celsius(°C) and Fahrenheit(°F).

USE & OPERATION (CONTINUED)

FUNCTION BUTTONS (CONTINUED)

WARNING LIGHT

Condensation may accumulate in the unit. If the internal tank becomes full, the Power Control light will ﬂash and the unit will not operate until the unit has been drained (refer to Water Condensation Drainage).

After switching the air conditioner off, you must wait 3 minutes before switching it back on again.

MODE CONTROL

Settings: Air Conditioning, Dehumidifying, Fan. The corresponding indicator light will illuminate to indicate the current mode setting.

Air Conditioning Mode

Adjust fan speed and air temperature to suit your desired comfort level. Temperature setting range is 16°C - 32°C (60°F - 89°F).

Dehumidifying Mode Air is dehumidiﬁed as it passes through the unit, without being in full cooling mode. If room temperature is higher than 25°C (77°F) fan speed can be adjusted; otherwise fan speed is preset to LOW. Note: If the unit will be used mainly as a dehumidifier, do not connect the exhaust hose. Continuous drainage is then necessary (refer to Continuous Draining for Dehumidiﬁer Mode).

Fan Mode

For air circulation without air conditioner cooling.

FAN SPEED CONTROL

Applicable for model MO08 Series: High and Low. Applicable for model MO10 Series: High, Medium, and Low.

FILTER ALERT

When the Filter Alert Light is ON, it is time to clean the ﬁlter. Switch the air conditioner OFF and carefully remove the ﬁlter from the unit and clean. Replace the ﬁlter and switch ON the air conditioner. The Filter Alert Light should not be illuminated until the ﬁlter requires cleaning again. The frequency of ﬁlter cleaning depends on room environment conditions. Some rooms may require changing more frequently than others.

USE & OPERATION (CONTINUED)

REMOTE CONTROL

The functions work the same as the Portable Air Conditioner's Control Panel. All key functions can be accessed from the remote control.

Power Control

ON / OFF

Fan Speed Control

Applicable for model MO08 Series:

ť)*()ť-08

Applicable for model MO10 Series:

ť)*()ť.*%ť-08

Timer Control

In running mode: Auto switch off In stand-by mode: Auto switch on Press ź or Ÿ button to adjust the time setting for 1 hour intervals.

Temperature / Timer Set

Used for adjusting the timer and

temperature. When the ź orŸ key is pressed, the

set temperature is displayed and may be adjusted Timer setting is available from 1 - 24 hours

by pressing the key ź or Ÿ.

Mode Control

Press this button to change the operation mode in the order of:

Air Conditioning Dehumidifying

Fan

Note:

Battery Installation: Remove the cover on the back of the remote control and insert two AAA batteries with + and - pointing in the proper direction according to the polarity markings.

Caution:

Use only two AAA or IEC R03 1.5V batteries.

Remove the batteries if the remote control is not in use for a month or longer.

All batteries should be replaced at the same time, do not mix with old batteries.

Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

Properly dispose of used batteries.

This device complies with part 15 of the FCC Rules. Operation is subject to following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

ť3FPSJFOUPSSFMPDBUFUIFSFDFJWJOHBOUFOOB ť*ODSFBTFUIFTFQBSBUJPOCFUXFFOUIFFRVJQNFOUBOEUIFSFDFJWFS ť$POOFDUUIFFRVJQNFOUJOGPBOPVUMFUPOBDJSDVJUEJGGFSFOUGSPNUIBUUPXIJDIUIFSFDFJWFSJTDPOOFDUFE ť$POTVMUUIFEFBMFSPSBOFYQFSJFODFESBEJP57UFDIOJDJBOGPSIFMQ

Caution: Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

8EN

CLEANING & MAINTENANCE

Appliance Maintenance:

Turn off the appliance before disconnecting the power supply.

Only clean the appliance with a soft dry cloth.

Dust Filter Maintenance:

The dust ﬁlter is to be cleaned every two weeks to maintain air cooling efﬁciency. Please follow the below instructions for cleaning the dust ﬁlters:

Turn off the appliance and remove the upper and lower dust ﬁlters. Rinse it in lukewarm water. After cleaning, dry in

a shaded and cool place, then reinstall.

End of Season Storage & Maintenance:

If the appliance will not be used for a long time, follow these steps:

Be sure to drain the left-over water condensation. Remove the lower drain plug and use a shallow pan to collect the water (make sure to replace the drain plug when ﬁnished).

To dry excess moisture, run the unit in Fan only mode for 30 minutes before storing.

Turn off and unplug the air conditioner from the power supply.

Remove the dust ﬁlter and clean with water. Dry the dust ﬁlter and then reinstall.

Disconnecting the Window Installation Kit:

Remove the Exhaust Hose from the unit by pressing the release button located on the right side of the Hose and then sliding the Hose to the right side.

Remove the Window Bracket, Window Bracket Panel Adapter and Exhaust Hose Connector.

It is recommended to store the Window Kit parts in a bag together with the Remote Control and placing them together with the air conditioner unit. If needed, you can clean the Window Kit with a damp cloth and water before storing.

Make sure all parts of the Window Kit are dry before storage.

Cover the air conditioner with a cloth/ plastic bag before storage, to protect from dust and scratches collecting on the surface of the unit. It is recommended to coil the power cord before storing to ensure the cord is protected from

bents and creases. Store the air conditioner in a cool, dry place, away from direct sunlight.

Upper Dust Filter

Lower Dust Filter

WATER CONDENSATION DRAINAGE

When there is excess water condensation inside the unit, the air conditioner stops running and shows a warning light (the Power Control button ﬂashes with a red light). This warning light indicates that the water condensation needs to be drained using the following procedures:

Manual Draining for AC & Dehumidiﬁer Mode

Water may need to be drained in high humidity areas.

Unplug the unit from power source.

Place a shallow pan under the lower rubber drain plug. See diagram.

Remove the lower rubber drain plug.

Water will drain out and collect in the shallow pan.

After the water is drained, replace the lower rubber drain plug ﬁrmly. You can now turn on the unit.

Continuous Draining for Dehumidiﬁer Mode

While using the unit in dehumidiﬁer mode, continuous drainage is recommended.

Shallow Pan (Not included)

Lower Rubber Drain Plug

Unplug the unit from power source.

Remove the upper/lower rubber drain plug. Some residual water may spill so please have a pan to collect the water. See diagram.

Connect the drain connector to a ¾” hose or standard garden hose (not included).

The water can be continuously drained through the drain tube into a ﬂoor drain or bucket. Replace the drain plug.

You can now turn on the unit.

Upper Rubber Drain Plug

Drain Tube

TROUBLESHOOTING GUIDE

The following troubleshooting guide addresses the most common problems. If problems persist, call customer support. Unplug and disconnect the appliance from the power source before attempting to troubleshoot.

PROBLEM POSSIBLE CAUSE SOLUTION

No electricity. Check for power.

Batteries in the remote

The air conditioning unit does not start

control need to be replaced.

The power cord is not properly plugged in.

Change remote control batteries.

Remove and reconnect the power cord.

Runs a short while only

The safety LCDI plug has tripped (USA / Canada / Mexico only).

The thermostat temperature setting is too close to room temperature.

Air outlet is blocked. Make sure the exhaust hose is properly connected.

There are tight bends in the air exhaust hose.

Reset the safety LCDI plug, if problem persists contact our customer support (USA / Canada / Mexico only).

Lower the set temperature.

Connect exhaust hose as per instructions on page 4.

+ 32 hidden pages