IMPORTANT
SAFETY INSTRUCTIONS
READ AND SAVE THESE SAFETY
INSTRUCTIONS BEFORE USING
THIS FAN
When using electrical appliances, basic
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
FOR US MODELS ONLY - This product
employs overload protection (fuse). A blown
fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the
product from the outlet. Replace the fuse as
per the user servicing instructions (follow
product marking for proper fuse rating)
and check the product. If the replacement
fuse blows, a short-circuit may be present
and the product should be discarded or
returned to an authorized service facility
for examination and/or repair.
1. Use this fan only as described in this
manual. Other use not recommended
as it may cause fire, electric shock or
injury to persons.
2. This product is intended for household
use ONLY and not for commercial,
industrial or outdoor use.
3. To protect against electric shock, do not
place fan in window, immerse unit, plug
or cord in water or spray with liquids.
4. This appliance has a polarized plug
(one blade is wider than the other). To
reduce the risk of shock, this plug is
intended to fit only one way in a polarized
outlet. If the plug does not fit fully in the
outlet, reverse the plug. If it still does
not fit, contact a qualified electrician.
DO NOT attempt to defeat this safety
feature.
5. Close supervision is necessary when any
appliance is used by or near children.
6. Turn the fan OFF and unplug the fan from
the outlet when not in use, when moving
the fan from one location to another and
before cleaning.
7. To disconnect the fan, first turn the unit
OFF, grip the plug and pull it from the wall
outlet. Never pull the plug by the cord.
8. Do not operate the fan in the presence
of explosive and/or flammable fumes.
9. Do not place the fan or any parts near
an open flame, cooking or other heating
appliance.
10. Do not operate the fan with a
damaged cord or plug or if the product
malfunctions, is dropped or damaged in
any manner (see warranty).
ADVANCED QUIETSET®
WHOLE ROOM STAND FAN
with Noise Reduction Technology
HSF600 Series
Owner’s Manual
Honeywell is a trademark of Honeywell International Inc., used under license by Helen of Troy Limited.
Honeywell International Inc. makes no representation or warranties with respect to this product.
QuietSet is a registered trademark owned by Helen of Troy Limited.
2
FUSED SAFETY PLUG - FOR US MODELS ONLY
USER SERVICING INSTRUCTIONS
• If your fan loses power and you suspect that the fuse on your fan has
blown, grasp plug and remove from the receptacle or other outlet
device. Do not unplug by pulling on cord.
• Slide fuse cover, located on the top of the plug towards the prongs of
the plug. (Fig. 1)
• Carefully remove the blown fuse and snap a new fuse into place. To
Reduce the Risk of Fire, replace fuse only with 2.5 Amp, 125 volt fuse.
Fully close the fuse door by sliding back into place. (Fig. 2) Discard the
blown fuse. The plug should now be ready for normal use.
• To Reduce the Risk of Fire, do not replace attachment plug.
Contains a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
• If you need further information on how or when to replace the fuse in
the safety plug, please contact Kaz Consumer Relations Department
by visiting our website at www.honeywellpluggedin.com/fans
or calling 1-800-477-0457.
This fan features a fused safety plug which is designed to cut off electric current to the fan if an
electrical fault occurs. Please see below for more information on how to properly use your fan and
replace the safety plug fuse, if needed.
11. Do not use an extension cord or power
strip with this fan.
12. Avoid contact with moving fan parts.
13. The use of attachments not recommended
by the manufacturer may be hazardous.
14. Place the fan on a dry level surface.
15. Do not hang or mount fan on a wall
or ceiling.
16. Do not operate if the fan housing is
damaged.
17. A loose fit between the AC outlet
(receptacle) and plug may cause
overheating and a distortion of the plug.
Contact a qualified electrician to replace
loose or worn outlet.
18.
Do not
operate any fan with a damaged
cord or plug. Discard any damaged fan,
return the fan to the retailer where the
fan was purchased, or request a return
authorization to return to Kaz, Inc. for
examination and/or repair.
19.
Do not
run fan cord under carpeting. Do
not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances. Arrange
cord away from traffic areas and where it
will not be tripped over.
WARNING: To Reduce The Risk of Fire
or Electric Shock, Do Not Use This Fan With
Any Solid State Speed Conrol Device
Fig. 1
Fig. 2
3
ASSEMBLY INSTRUCTIONS
A. BASE ASSEMBLY
• Remove the L shaped bolt (counter clockwise) and
washer from the bottom of the silver fan pole. (Fig. 3).
Fig.3
Fig.5
Fig.6
Fig.4
Base
Control
Panel
Rear Grille
Mounting Nut
Motor
Assembly
Oscillation
Knob
Remote
Control
Twist and Lock Height
Adjustment
Blade Knob
Rear Grille
Fan Blade
Clips
Metal Fan Pole
Thumb Screw
L Shaped Bolt
Front Grille
B. SECURING THE FAN TO THE BASE
• Extend the silver pole to its full length, place the
fan pole into the base. (Fig. 4).
• Align the pole in the base using tabs as a guide.
• Gently place base on its side. (Fig. 5).
• Insert and tighten the L shaped bolt and washer
on the bottom of the fan base. (Fig. 6).
• Tighten by turning clockwise. (Fig. 6).
4
ASSEMBLY INSTRUCTIONS (continued)
Fig.15
Fig.14
Align slot
with pin
• Align hole in center of Fan Blade with the screw extending from the Motor Assembly (Fig. 13).
Make sure that the 2 slots on the back of the Fan Blade align with the bars extending from the
shaft surrounding the screw attached to the Motor Assembly. (Fig. 14).
Then push the Fan Blade into place.
• Attach the blade knob on the center of the fan, tighten by turning COUNTER CLOCKWISE (Fig. 15).
Screw
from motor
assembly
Fig.13
C. ASSEMBLING THE UPPER PORTION OF THE FAN
• Remove the thumb screw from the lower portion of the fan motor assembly by turning it
counter-clockwise (Fig. 7)
• Insert the Fan Motor Assembly into the Fan Pole (Fig. 8), once both halves are aligned reinsert
the thumb screw (Fig. 9) and tighten by turning clockwise.
• Circular Rear Grille Mounting Nut will come attached to the Motor Assembly. Remove it by
turning COUNTER-CLOCKWISE. You will re-attach the Rear Grille Mounting Nut later (Fig. 10).
• Place the Rear Grille onto the Motor Housing, making sure the 2 holes in the center of the Rear
Grille fit over the 2 raised knobs on the Motor Housing (Fig. 11). Now place the Rear Grille
Mounting Nut onto the center of the fan, and tighten by turning it CLOCKWISE (Fig. 12).
Fig.8
Fig.7
Fig.9
Fig.12
Rear Grille
Mounting
Nut
Fig.10
Fig.11
5
D. DETERMINING THE HEIGHT OF THE FAN
The unique Twist & LockTM height adjustment feature lets you choose the perfect height for your
cooling needs. Twist the top pole and either pull up or push down to find your ideal height then
twist again to lock in place. (see label on back of fan pole);
• Securely grasp the top portion of
the pole and twist counter clockwise
to unlock.
• Pull up or push down to adjust height
(placing your foot or hand gently on
the base will help with the height
adjustment) (Fig 17).
• Once you have selected the desired
height, twist clockwise until you feel
the pole lock into place. (Fig 18).
• DO NOT USE THE SCREW on the
pole for height adjustment.
ASSEMBLY INSTRUCTIONS (continued)
• Properly align the Front Grille with the Rear Grille (Fig. 16). To secure the Front Grille onto the
fan, raise the built-in clips around the Front Grille and fasten these clips onto the Rear Grille.
Fig.18Fig.17
Fig.16
REMOTE CONTROL BATTERY INSTALLATION/REPLACEMENT INSTRUCTIONS
A. Remove battery door by sliding downward in direction of arrow.
B. Insert 2 AAA batteries (not included) into the remote following
the directional guides in the recessed slots (Fig. 19).
C. Replace battery door by sliding upward opposite of arrow
direction until door snaps in place.
NOTE: DO NOT MIX OLD AND NEW BATTERIES. DO NOT MIX
ALKALINE, STANDARD (CARBON-ZINC) OR RECHARGEABLE
(NICKEL-CADMIUM)BATTERIES.
SEE RECYCLERS IN YOUR AREA FOR PROPER DISPOSAL OF BATTERIES.
Fig.19
6
OSCILLATION
• Oscillation Knob is located on the top
panel of the Motor Housing.
• To START fan oscillation, push the
Oscillation Knob DOWN.
• To STOP fan oscillation, pull the Oscillation
Knob UP. (Fig. 21).
ON/OFF
To turn fan on, press the Power
button ( ) located at the bottom
of the control panel (Fig. 20).
SPEED CONTROL
To adjust the speed up or down,
press the Fan Speed button ( )
repeatedly to increase level (Fig. 20).
TIMER
Choose from 1, 2, 4, or 8 hour
settings by performing the following
function (Fig. 20):
• 1 hour: Press the Timer button
( ) once.
• 2 hours: Press the Timer button
twice.
• 4 hours: Press the Timer button
a third time.
• 8 hours: Press the Timer button
a fourth time.
HSF600 SERIES FAN OPERATION
AUTO DIM LIGHT FEATURE
Control panel light automatically dims to 50% brightness after 15 seconds and resumes to 100%
brightness when settings are changed.
Fig.21
Oscillation knob
Up/OFF
Down/ON
Press the Timer button a fifth time
to turn the Timer feature off.
Timer
Speed
Power
Fig.20
Model HSF600B, HSF600W
Timer
Speed
Power
Fig.20
Model HSF600BC, HSF600WC
7
USER SERVICING INSTRUCTIONS
CLEANING AND STORAGE
• Be sure your fan is in the OFF position.
• Unplug the fan before cleaning.
• Use only a soft, damp cloth to gently wipe the fan clean.
• DO NOT immerse the fan in water and never allow water to enter the Motor Housing.
• DO NOT use gasoline, paint thinner or other chemicals to clean the fan.
REMOVAL OF THE FRONT GRILLE FOR CLEANING
• Remove the Front Grille by releasing the Grille clips.
• Unscrew the Blade Knob by turning it CLOCKWISE (REVERSE THREAD).
• Pull the Fan Blade away from the Motor Housing.
• Gently wipe the Fan Blade and Grilles with a soft, damp cloth.
• Assemble the fan by following the last three steps in the ASSEMBLY INSTRUCTIONS.
STORAGE
• For storage disassemble and clean the fan carefully as instructed. Store the fan in its original
box. You may also leave the fan fully assembled and covered with plastic to protect it from dust.
Store your fan in clean, dry place.
ON/OFF
Remove remote control from the back of the fan. The remote control will not work while in the
fan housing. Press the Power button ( ) once to turn the fan on. Press the Power button a
second time to turn the fan off (Fig.22).
SPEED CONTROL
To adjust the speed up or down, press the Fan Speed
button ( ) repeatedly to increase level (Fig.16).
TIMER
Choose from 1, 2, 4, or 8 hour settings by performing
the following function (Fig.22):
• 1 hour: Press the Timer button ( ) once.
• 2 hours: Press the Timer button twice.
• 4 hours: Press the Timer button a third time.
• 8 hours: Press the Timer button a fourth time.
Press the Timer button a fifth time to turn the Timer feature off (Fig. 22).
HSF600 SERIES REMOTE CONTROL OPERATION
Speed
Timer
Power
Fig.22
CONSUMER RELATIONS
CUSTOMER SERVICE
Questions or Comments
Call us toll-free at: 1-800-477-0457
E-mail: consumerrelations@kaz.com
Or visit our website at: www.HoneywellPluggedIn.com/fans
Please be sure to specify model number.
8
1 YEAR LIMITED WARRANTY
You should first read all instructions
before attempting to use this product.
A. This 1 year limited warranty applies
to repair or replacement of product
found to be defective in material or
workmanship. This warranty does
not apply to damage resulting from
commercial, abusive, unreasonable use
or supplemental damage. Defects that
are the result of normal wear and tear
will not be considered manufacturing
defects under this warranty. KAZ IS
NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY
NATURE. ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.
Some jurisdictions do not allow the
exclusion or limitation of incidental or
consequential damages or limitations on
how long an implied warranty lasts, so
the above limitations or exclusions may
not apply to you. This warranty gives
you specific legal rights, and you also
may have other rights which vary from
jurisdiction to jurisdiction. This warranty
applies only to the original purchaser
of this product from the original date
of purchase.
B. At its option, Kaz will repair or replace
this product if it is found to be defective
in material or workmanship.
C. This warranty does not cover damage
resulting from any unauthorized
attempts to repair or from any use not in
accordance with the instruction manual.
Call us toll-free: 1-800-477-0457 or
e-mail: consumerrelations@kaz.com
Please be sure to specify a model number
located on the box and the back and bottom
of your unit.
To register your product, please go to
www.honeywellpluggedin.com/register to
register your product under the Customer Care
Center and receive product information updates
and new promotional offers.
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE
CONTACT CONSUMER RELATIONS FIRST
OR SEE YOUR WARRANTY. DO NOT RETURN
THE PRODUCT TO THE ORIGINAL PLACE OF
PURCHASE. DO NOT ATTEMPT TO OPEN THE
MOTOR HOUSING YOURSELF, DOING SO MAY
VOID YOUR WARRANTY AND CAUSE DAMAGE
TO THE PRODUCT OR PERSONAL INJURY.
9
CONSIGNES DE
SÉCURITÉ IMPORTANTES
LISEZ ET CONSERVEZ CES
MESURES DE SÉCURITÉ AVANT
D’UTILISER CE VENTILATEUR
Lorsque
vous utilisez des appareils électriques, vous
devez toujours prendre certaines précautions
élémentaires pour réduire les risques d’incendie,
de choc électrique et de blessure corporelle,
notamment les mesures suivantes :
AUX ÉTATS-UNIS SEULEMENT - Cet appareil est
muni d’une protection contre les surcharges
(fusible). Un fusible grillé indique une surcharge
ou un court-circuit. Si le fusible grille, débranchez
l’appareil de la prise de courant. Remplacez
le fusible conformément aux instructions
d’utilisation (respectez les spécifications inscrites
sur la plaque signalétique de l’appareil pour
connaître le calibre approprié du fusible) et
vérifiez l’appareil. Si le fusible de rechange grille,
il peut y avoir un court-circuit et l’appareil devrait
être jeté ou retourné à un centre de réparation
autorisé pour examen et/ou réparation.
1.
N’utilisez ce ventilateur que selon la description
dans ce manuel. Toute autre utilisation
n’est pas recommandée puisqu’elle pourrait
causer un incendie, un choc électrique ou des
blessures corporelles.
2. Cet appareil est conçu pour un usage
domestique SEULEMENT et non pour un usage
commercial, industriel ou à l’extérieur.
3. Pour vous protéger contre les chocs
électriques, ne placez pas le ventilateur dans
une fenêtre, ne submergez pas l’appareil, la
fiche ou le cordon dans l’eau et ne le vaporisez
pas de liquides.
4. Cet appareil est muni d’une fiche polarisée (une
des deux broches est plus large que l’autre).
Pour réduire les risques de choc, cette fiche ne
peut s’insérer que d’une seule manière dans
une prise polarisée. Si les broches n’entrent
pas complètement dans les trous de la prise,
tournez la fiche dans l’autre sens. Si elles
n’entrent toujours pas, communiquez avec un
électricien qualifié N’ESSAYEZ PAS d’altérer ce
dispositif de sécurité.
5. Une étroite supervision est nécessaire lorsque
tout appareil est utilisé par des enfants ou près
d’enfants.
6. Éteignez et débranchez le ventilateur lorsqu’il
ne fonctionne pas, avant de le déplacer d’un
endroit à un autre et avant de le nettoyer.
7. Pour débrancher le ventilateur, commencez par
l’éteindre, saisissez la fiche et tirez-la de la
prise électrique. Ne tirez jamais sur le cordon.
8. Ne faites pas ofonctionner le ventilateur
en présence d’explosifs et/ou de vapeurs
inflammables.
VENTILATEUR SUR PIED
DE POINTE QUIETSET
MD
POUR UNE PIÈCE ENTIÈRE
avec technologie de réduction
du bruit
Série HSF600
Manuel du propriétaire
Honeywell est une marque de commerce de Honeywell International Inc., utilisée sous licence par Helen of Troy Limited.
Honeywell International Inc. ne fait aucune déclaration et n’offre aucune garantie en ce qui concerne ce produit.
QuietSet est une marque déposée propriété de Helen of Troy Limited.
Loading...