Page 1
4
6
0
1
5
1
5
6
1
r
a
b
0
2
8
0
bar
10
Construction
The domestic water station comprises:
• Housing with inlet and outlet pressure gauges
• Check valve on inlet
• Test point for check valve
• Fine filter in clear filter bowl
• Ball valve with drain connection
• Spring bonnet with adjustment knob and setting scale
• Valve insert complete with diaphragm and valve seat
• Threaded or soldered union connections
• Shutoff valve
• Double ring wrench
Materials
• Dezincification resistant brass housing
• Brass shutoff valve and connectors
• High grade synthetic material check valve cartridge
• Stainless steel fine filter
EN0H-1101GE23 R0109 • Subject to change
• Red-bronze or shock-resistant, clear transparent synthetic
material filter bowl
• High-quality synthetic material spring bonnet
• High-quality synthetic material valve insert
• Fibre-reinforced NBR diaphragm
• NBR seals
HS10S
Combination water supply unit
Product specification sheet
Application
HS10S combination water supply units integrate a check valve
with test point, reverse rinsing fine filter, pressure reducing valve
and shutoff valve in one appliance. They ensure a continuous
supply of filtered water. The fine filter stops the ingress of foreign
bodies, for example rust particles, strands of hemp and grains of
sand. The check valve protects the mains water system against
back pressure, back flow and back syphonage of health threatening liquids. The pressure reducing valve prevents over-pressure
damage and reduces water consumption.
All individual units correspond to the requirements of current DIN/
DVGW specifications. Technical features of each unit also apply
to the combination assembly.
Special Features
• DIN/DVGW approved
• Double Spin Technology for connection sizes
o Cartridge with external rotor enabling simultaneous
cleaning in lower and upper filter areas
o Visual function check possible
• Especially compact because pressure reducing valve, fine
filter, check valve and shutoff valve are combined in one unit
• Filtered water supplied even during reverse rinsing
• Patented reverse rinsing system - fast and thorough cleaning
of the filter with small amount of water
• Automatic reverse rinsing actuator with bayonet connector
can be retrofitted
• Shock resistant clear synthetic material filter bowl enables
easy checking of filter contamination
• Inlet pressure balancing - fluctuating inlet pressure does not
influence outlet pressure
• Filter and complete filter bowl are replaceable
• The valve insert is of high quality synthetic material and can
be fully exchanged
Range of Application
Medium Water
Inlet pressure Max. 16.0 bar with clear filter bowl
Max. 25.0 with red-bronze filter bowl
Outlet pressure 1.5 - 6.0 bar
The filter is constructed for drinking water installations. In case of
a process water application the filter has to be proven individually.
Technical Data
Installation position Horizontal, with filter bowl downwards
Operating temperatureMax. 40 °C with clear filter bowl
Max. 70 °C with red-bronze filter bowl
Operating pressure Min. 1.5 bar
Connection size
1
/2" - 2"
www.honeywell.com 3
1
/2" to 11/4"
Page 2
HS10S Combination water supply unit
Method of Operation
The combination water supply unit combines check valve,
reverse rinsing fine filter, pressure reducing valve and shutoff
valve in one appliance.
Water flows first through the check valve. This causes the valve
stem to push against the spring force and open the valve.
The downstream reverse rinsing fine filter holds back any dirt
particles in the water. These particles are then completely flushed
out by reverse rinsing.
Filters with Double Spin Technology have turbine blades which
circulate the water and thereby set the rotor on the upper filter
into a rotational motion. The internal impeller rinses off particles
that have adhered to the upper filter at the intersecting points
with the rotor.
The integral pressure reducing valve functions on a balanced
force principle whereby the force exerted by a diaphragm is
balanced against the force of an adjustment spring. The inlet
pressure has no influence on opening or closing of the valve. Inlet
pressure fluctuation does not therefore affect the outlet pressure.
Options
HS10S-...AA = Threaded male connections filter mesh size
100 µm
HS10S-...AAM = Red-bronze filter bowl, Threaded male
connections filter mesh size 100 µm
Connection size
Filters with other mesh widths available on request
Connection size R
Nominal size
DN 15 20 25 32 40 50
1
/2"
diameter
Weight approx. kg 4.0 4.1 5.7 6.3 8.1 10
Dimensions mm
L 255 268 305 327 370 408
l 110 110 130 130 150 150
H 439 439 493 493 590 590
h 350 350 353 353 417 417
D97979797120120
-value 2.7 3.2 7.6 8.9 12.6 13.0
k
vs
DIN/DVGW Approval No. DW-9321 AT 2318
Double Spin Technologie Yes Yes Yes Yes No No
3
/4"1"1
1
/4"1
Accessories
Z11S Automatic reverse rinsing actuator
For automatic filter cleaning at presettable intervals
1
/2"2"
Z11S
4 www.honeywell.com
AF11S
AF11DS
AF11S Filter insert complete
Available with filter meshes 20 µm, 50 µm, 100 µm,
200 µm, 300 µm, 500 µm
AF11DS Filter insert complete
Available with filter meshes 20 µm, 50 µm, 100 µm,
200 µm, 300 µm, 500 µm (for filters with Double Spin
Technology)
* The filter guide (either with double spin or without double spin feature) is included
in the packaging of the replacement filter inserts (AF11DS and AF11S) only for the
sizes 1/2" up to 11/4!
EN0H-1101GE23 R0109 • Subject to change
Page 3
Installation Example
HS10S Combination water supply unit
Installation Guidelines
• Install in horizontal pipework with filter bowl downwards
o This position ensures optimum filter efficiency
• Install shutoff valves
• Ensure good access
o Pressure gauge can be read off easily
o Degree of contamination can be easily seen with clear filter
bowl
o Simplifies maintenance and inspection
• The installation location should be protected against frost
• Fit immediately after water meter
o Corresponds to DIN 1988, Part 2
Flow Diagram
Typical Applications
Combination water supply units of this type can be fitted
wherever check valves, filters, pressure reducing valves and
water distributor units are required. They can also be used for
commercial and industrial applications within the limits of their
specifications.
Combination water supply units of this type are installed:
• To comply with standards and where space is limited, for
example in modernisation of old buildings
• Where there is existing metal or plastics pipework
• For protection against noise when the static pressure at take
off points exceeds 5.0 bar (DIN 4109)
• If the static pressure exceeds the maximum permissible
operating pressure of an installation
• If pressure fluctuations in the downstream system must be
avoided
• If the downstream system includes appliances which must be
protected against dirt
EN0H-1101GE23 R0109 • Subject to change
www.honeywell.com 5
Page 4
HS10S Combination water supply unit
1
Spare Parts
HS10S Filter Combinations (from 2007 onwards)
No. Description Dimension Part No.
6
4
5
7
without Double Spin
Technology
2
3
with Double Spin
Technology
11
13
12
1 Spring bonnet completet1/2" + 3/4" 0901515
(with setting scale) 1" + 1
2 Valve insert complete
(without filter) 1" + 1
3 Seal ring set
1
/4" 0901517
1
1
/2" + 2" 0901518
1
/2" + 3/4"D06FA-1/2
1
/4"D06FA-1A
1
1
/2" + 2" D06FA-11/2
1
/2" + 3/4" 0901444
(Pack of 10) 1" 0901445
1
1
/4" 0901446
14
1
1
/2" 0901447
2" 0901448
4 Check valve
cartridge
1
/2" 2166200
3
/4" 2110200
1" 2164400
1
1
/4" 2164500
1
1
/2" 2164600
2" 2164700
5 Test valve
8
6 Pressure gauge (0-10 bar) M38K-A10
Pressure gauge (0-16 bar) M38K-A16
1
/2" - 2" 2421100
Pressure gauge (0-25 bar) M38K-A25
7 Filter insert complete*
Filter mesh 100 µm
8 Filter insert complete* for
filters with Double Spin
1
/2" - 3/4"AF11S-1/2A
1" - 11/4"AF11S-1A
1
/2" - 2" AF11S-11/2A
1
1
/2" - 3/4" AF11DS-1/2A
"
1
- 11/4"AF11DS-1A
Technology, Filter mesh
100 µm
1
9 Clear filter bowl
10 Red-bronze filter bowl
11 O-ring set
(Pack of 10) 1
12 Drain connector
9
13 Ball valve complete
14 Shutoff valve
(not included in
HS10S-ZS)
/2" - 11/4" KF11S-1A
1
1
/2" - 2" KF11S-11/2A
1
/2" - 11/4" FT09RS-1A
1
1
/2" - 2" FT09RS-11/2A
1
/2" - 11/4" 0900747
1
/2" - 2" 0900748
1
/2" - 2" AA76-1/2A
1
/2" - 2" KH11S-1A
1
/2" 2192900
3
/4" 2193100
1" 2193200
1
1
/4" 2193300
1
1
/2" 2193400
2" 2193500
15 Double ring wrench
for removing filter bowl 1" - 1
and spring bonnet (no fig.) 1
* The filter guide (either with double spin or without double spin feature) is included
in the packaging of the replacement filter inserts (AF11DS and AF11S) only for the
sizes 1/2" up to 11/4!
1
/2" - 3/4" ZR10K-3/4
1
/4" ZR10K-1
1
/2" - 2" ZR10K-11/2
Automation and Control Solutions
Honeywell GmbH
Hardhofweg
D-74821 Mosbach
Phone: (49) 6261 810
Fax: (49) 6261 81309
http://europe.hbc.honeywell.com
www.honeywell.com
Manufactured for and on behalf of the
Environmental and Combustion Controls Division
of Honeywell Technologies Sàrl, Rolle, Z.A. La
Pièce 16, Switzerland by its Authorised Representative Honeywell GmbH
EN0H-1101GE23 R0109
Subject to change without notice
© 2009 Honeywell GmbH
Loading...