Honeywell HD32X, HFD32X User Manual

AIR GENIUS
AIR CLEANER/
ODOR REDUCER

For Model Series
HD32X, HFD32X

IMPORTANT SAFETY
INSTRUCTIONS

READ AND SAVE THESE
SAFETY INSTRUCTIONS
BEFORE USING THIS
AIR CLEANER

When using electrical appliances, basic
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:

1. Read all instructions before operating the

air cleaner.

2. Place air purifier where it is not easily knocked

over by persons in the household.

3. Always turn the air cleaner controls to the

OFF position and unplug from the wall outlet

when not in use.

4. To disconnect the air cleaner, press the

Power button to turn the unit off, grip the plug
and pull it from the wall outlet. Never pull by
the cord.

5. Do not use any product with a damaged cord

or plug or if product malfunctions, is dropped
or damaged in any manner. Keep the cord
away from heated surfaces.

6. Do not use air cleaner outdoors.

7. Never use air cleaner unless it is fully

assembled.

8. Do not run power cord under carpets, and do

not cover with throw rugs. Arrange cord such
that it will not be tripped over.

9. Do not use air cleaner where combustible

gases or vapors are present.

10. Do not expose the air cleaner to rain, or use

near water, in a bathroom, laundry area or
other damp location.

11. The air cleaner must be used in its upright

position.

12. Do not allow foreign objects to enter ventilation

or exhaust opening as this may cause electric
shock or damage to the air cleaner. Do not
block air outlets or intakes.

13. Locate air cleaner near the outlet and avoid

using an extension cord.

14. To reduce the risk of electric shock this

equipment has a grounding type plug that has
a third (grounding) pin. This plug will only fit
into a grounding type power outlet. If the plug
does not fit into the outlet, contact qualified
personnel to install the proper outlet.

Do not alter the plug in any way.

15. A loose fit between the AC outlet (receptacle)

and plug may cause overheating and a
distortion of the plug. Contact a qualified
electrician to replace loose or worn outlet.

16. Do not sit, stand or place heavy objects on the

air purifier.

17. Disconnect power supply before servicing.

WARNING: To Reduce The Risk of
Fire or Electric Shock, Do Not Use This
Air Purifier With Any Solid-State Speed
Control Device.

The Honeywell Trademark is used by Kaz USA, Inc. under license from Honeywell International Inc.

Honeywell International Inc. makes no representation or warranties with respect to this product.

YOUR AIR PURIFIER

Washable
Pre-filter (1)

Front Grille

Permanent Washable

ifD® Filter (1)

Rear

Grille

OPTIONAL:

Odor-

reducing

Pre-filter K

ODOR REDUCTION

This air cleaner includes a special odor absorbing pre-filter K packed in the product box. In order to enjoy
the benefits of enhanced odor reduction, replace the washable pre-filter that is already in the air cleaner
with the odor absorbing pre-filter K.

For optimal performance, the pre-filter is wrapped in plastic to keep it fresh. Pre-filter replacement timing
will be approximately 3 months, depending on use.

You can purchase replacement K pre-filters at your local Home Depot store or they can be ordered
directly at www.HomeDepot.com. If you have any questions, contact Kaz Consumer Services at
1-800-477-0457.

NOTE: Please only use one pre-filter in your air cleaner at a time. You will need to choose whether you
want to use the permanent washable pre-filter or the odor reducing pre-filter (will be discarded after use).
Both are included with your air cleaner at the time of purchase.

HOW YOUR AIR CLEANER WORKS

This model air cleaner incorporates a 3-stage cleaning
system to help clean the air that passes through the filter
in the unit (Fig. 1).

Stage 1: Washable or Odor-reducing Pre-filter
(your choice)

Stage 2: Permanent Washable ifD® Filter
Stage 3: Electronic Ionizer

2

Fig. 1

SET-UP

• Select a firm, level and flat location. For best airflow, locate the unit 3 feet (1 M) from any wall or

furniture.

• When operating, large volumes of air are drawn toward the air cleaner. Surrounding areas should be

cleaned and/or vacuumed frequently to prevent build-up of dust and other contaminates. This may
also help prolong the life of the filter. If the unit is placed on a light colored carpet, a small mat or rug
should be used underneath to prevent permanent staining. This is especially important in homes with
contamination from smoking or fireplaces.

ENERGY STAR

®

This product earned the ENERGY STAR® by meeting strict energy efficiency guidelines set by
the US EPA. US EPA does not endorse any manufacturer claims of healthier indoor air from
the use of this product.

The energy efficiency of this ENERGY STAR® qualified model is measured based on a ratio
between the model’s CADR for Dust and the electrical energy it consumes, or CADR/Watt.

OPERATION

• Ensure the air cleaner is plugged into a working electrical outlet.

• Press the power button ( ) once. The unit will start at the “general cleaning”

level and remain on this setting until another cleaning level is chosen (Fig. 2).

It is recommended that you run your air purifier when you are at home to
clean the air. The unit may be run 24 hours a day if preferred for continuous
cleaning. This unit will be more effective when doors and windows are
closed.

Fig. 2

3

CONTROLS THAT DO THE THINKING FOR YOU

HD320, HFD320 Series

Max Cleaning Setting

Allergen Reduction Setting

General Cleaning

Setting

Germ Reduction Setting

Sleep/Quiet

Setting

Auto-off Timer

Power Button

Filter Status

Filter Reset Button

Accent Light

Button

Oscillation Button

Purification Level

Button

Auto-off Timer Button – Tap this icon if you would like your air cleaner to run and then automatically shut-off

after a certain amount of time (choose from between 2, 4, 6, 8, 10 and 12 hours). This is convenient if you
would like your air cleaner to run during the night but then shut-off automatically in the morning (choose the
8 or 10 hour setting).

Purification Level Button – Your air cleaner will start off on the General Cleaning setting each time you turn

your air cleaner on.

LEVEL 5 - MAX

Best for power cleaning the air when unpleasant odors are noticeable, your room is particularly dusty or you
can sense that airborne particles are present. This setting cleans the air the fastest of all the settings and
circulates the air frequently in a room.

LEVEL 4 - ALLERGEN

This setting makes the air cleaner perform at the proper level for reducing many types of airborne allergens.
It ensures the allergen capturing efficiency and rate is best for the particle sizes being captured. Best for
fighting airborne allergens during high allergen season, particularly in the spring and fall to help reduce
airborne pollen. Also great for year-round reduction of pet dander allergens.

LEVEL 3 - GENERAL

Best for General Cleaning. Use this setting to help reduce airborne dust and smoke particles, like those from
cooking or tobacco smoke.

LEVEL 2 - GERM

This setting slows down air movement so airborne microscopic germs are most effectively captured in
the filter. Germs, like certain bacteria and viruses, can be much smaller than other airborne particles or
organisms. Giving the germs more time to dwell in the filter increases the filtration efficiency. This setting
can be used during cold and flu season to help reduce certain germs from the air that passes through the filter.

4

CONTROLS CONTINUED

LEVEL 1 - SLEEP

Best for ultra quiet operation, perfect for nighttime use when sleeping.

Filter Status and Check Filters Button – Allows you to monitor how dirty your filter is getting. When it is time

to check and clean the filter, an indicator will illuminate notifying you that it is time to check the filters. When
this light comes on, you will need to clean your primary ifD® filter and clean or replace your pre-filter. (See
Filter Cleaning instructions). After you have cleaned or replaced the filters, press the Check Filters Indicator
until the light goes off.

Accent Light Indicator – Your air cleaner features a soft accent light at the bottom of the unit that provides a

nice glow around the base. You can choose to operate your unit with or without this accent light turned on. If
you want to use the light feature, you can choose from between a low or high light level.

Oscillate Button – Tap this icon if you want your air cleaner to gently rotate from side to side.

This will help increase circulation in the room.

OSCILLATION FEATURE

To help circulate fresher, cleaner air through the room, this unit has an oscillation

Fig. 3

feature. (Fig. 3)

• The oscillation feature is activated by tapping the Oscillation symbol ( ).
‘Tap’ the oscillation symbol once to turn the feature on, and then again to

turn it off.

BASIC OPERATION OF THE CLEANING SETTINGS

This model features a touch screen that senses when your finger touches

Fig. 4

the panel.

• The air cleaner automatically starts at the General Cleaning level when you turn
your unit on.

• Tap the Purification level symbol ( ) to cycle through the different cleaning
levels (please note that this is not a button, it is a touch-sensitive symbol, Fig. 4)
When ‘tapped’ the cleaning level will move to the next highest level until it is on
‘Max’. If you ‘tap’ the Purification symbol while it is on ‘Max’ the level will drop
back down to ‘Sleep’.

• Toggle through the levels until the LED light is illuminated at the level you want the unit to operate.

5

SETTING THE TIMER OPTION

• The timer option on the left of the control panel (see Fig. 5) allows you to select
how long the unit will run before it turns off automatically.

• ‘Tap’ the Timer symbol ( ) to shift through the options. When pressed the time
will move to the next highest setting until it is on ‘12’ (which means it will stay
on for 12 hours and then shut-off). If you tap the Timer symbol while it is on
‘12’ the timer option will turn off and the unit will run continuously. If you ‘tap’ it
again, it will start back at ‘2’.

• Toggle through the hour options until the LED light is illuminated behind the
number of hours you want the unit to operate for. If the Auto-off Timer is not
illuminated, the air purifier will run continuously.

ELECTRONIC FILTER CLEAN REMINDER

• This model air cleaner has an electronic filter check to remind you when to
check the washable ifD® filter based on the air purifier’s hours of use.

• When the ifD® filter needs to be cleaned, the LED light ‘bar’ will remain full and
the light will be illuminated until it is RESET. You may unplug the air cleaner
without interrupting the filter check.

• You should periodically check the filter. Depending on operating conditions,
the filter should be cleaned at least once every three months.

To RESET the Electronic Filter Check:

• When the filter monitor light remains on, it is time to check/clean the
ifD® filter and reset the filter monitor, if needed.

• After the filter has been cleaned and placed back in the unit (dry), you will want
to reset the indicator. To do this, ‘touch’ the ‘OK’ button for 2 or more seconds
until the LED light is off and the fill ‘chart’ is not illuminated.

Fig. 5

Fig. 6

Fig. 7

REMOVING THE FILTER

CAUTION: Turn off the unit and wait 60 seconds before removing

Fig. 8

the grille to clean filters.

The ifD® filter is supplied within the air cleaner.

• Turn-off the air cleaner. Wait 60 seconds and unplug the unit before removing
the grille. While pressing down on the notch along the rear grille, pull the grille
down and towards you and remove it (Fig. 8). Gently push along the edge of
the filter frame and pull forward.

• To place the filter back into the air cleaner housing, insert at the bottom and ensure that it is pushed in as
far as it can go, then push in from the top. To replace filter grille, align pin on bottom of grille with opening
on the housing and snap back into place. If the filter grille is not properly inserted, your air purifier may
not turn on. Ensure it is properly installed and there is no gap between grille and the housing.

NOTE: If the odor reducing pre-filter is used in lieu of the permanent washable pre-filter, it will need to be
replaced approximately every 3 months.

6

CLEANING THE IFD® FILTER

The ifD® filter should be cleaned approximately once every 3 months.

Fig. 9

To clean the ifD® filter:

• Turn the power off and unplug the air purifier.

• After removing the ifD® filter from the air purifier, follow the steps below to
wash the ifD® filter.

Rinsing:

• Rinse the filter with clean tap water (Fig. 9)

• If the filter still appears dirty, proceed to “Washing,”
otherwise proceed to “Drying.”

Washing:

• Remove the ifD® filter from the unit.

• Fill a sink with lukewarm water and add a few drops of mild dish soap.

• Gently swish the filter in the soap solution to clean.

• Soak the filter for 2-3 minutes. Do not leave for an extended period of time.

• Rinse the filter with clean tap water (Fig. 9).

Drying:

• Shake the filter to remove any excess water.

• Place the filter with the honeycomb side down on a plush towel.

• Note that the filter may still be discolored even after washing.

This is acceptable and will not affect performance.

• Allow the ifD® filter to dry for a few hours or overnight.

• When the ifD® filter is completely dry, place back into the air purifier.

CAUTION:

• Never place a wet ifD® filter in your air purifier.

• The ifD® filter is NOT dishwasher safe. Do not place the ifD® filter in a dishwasher or subject it to other
extreme hot water conditions.

• Do not use any solvents, strong cleaning agents or flammable liquids to clean the ifD® filter.

7

MAINTAINING YOUR WASHABLE PRE-FILTER

The pre-filter helps pick up large airborne particles that

Fig. 10

Fig.11

enter the rear grille. This pre-filter can be periodically
removed and shaken to clean it. Alternatively, it can be
rinsed by hand under warm water (Fig. 10). Let the
pre-filter air dry completely before inserting back into
the grille (Fig. 11). If you need to replace this item, please
call 1-800-477-0457 or visit www.kaz.com.

OPTIONAL: Changing the Odor Absorbing Pre-Filter

If you have chosen to use the odor absorbing K pre-filter that came with your air
purifier, it will lose its effectiveness for odor adsorption over time and will need to
be replaced.

To purchase K replacement pre-filters, they should be available at your local
Home Depot store or they can be ordered directly from www.HomeDepot.com. If
you have any questions, contact Kaz Consumer Services at 1-800-477-0457.

If using the odo r absorbing pre-filter, it is recommended that you store the original
washable pre-filter in the event that you decide to use it in the future.

To insert it into the unit, simply place securely into the rear grille in lieu
of standard pre-filter as shown in figure 11.

Washable
Pre-filter

Grille

NOTE: The odor absorbing pre-filter is not washable.

CLEANING AND STORAGE

We recommend that you clean the air purifier at least once every 3 months and before extended storage.
Use only a dry cloth to wipe the external surfaces of the air purifier. DO NOT USE WATER, WAX POLISH,

OR ANY CHEMICAL SOLUTION.

Rear

REPLACEMENT FILTERS

To order a replacement odor reducing pre-filter K, go to www.HomeDepot.com. If you have any
questions, contact 1-800-477-0457.

Odor Absorbing Pre-Filter K: Model HRF-K2 (2 pack)

8