Honeywell HD3 Installation Manual, Operation And Maintenance Manual

HD3 equIPTM Series Indoor Fixed Mini Dome Network

4S Box
(Optional)

Gasket
5-inch Dome
Adapter Plate
Screws (x2)

Camera
assembly

5-inch
Dome bubble

Note See the other side of this document for an

illustration of the 5-inch dome adapter plate.

Dome liner

Installation with a 4S Box Shown

Camera 5-inch Dome Adapter Plate Installation Guide

Replacing a KD5 camera with an HD3 equIP Series camera

Use this 5-inch dome adapter plate from the HD3IP-5K adapter kit if you are:

• Replacing a KD5 camera with an HD3 equIPTM Series Indoor Fixed Mini Dome Network

• Installing a 5-inch dome bubble onto your HD3 equIP

You can flush mount your HD3 equIP Series camera with or without a 4S box.

camera, and you want to use the 5-inch dome bubble.

Network camera.

1. Remove your installed KD5 camera. Set aside the 5-inch
dome bubble, and discard the rest.

2. Install the 5-inch dome adapter plate:

• Without a 4S Box: Use the supplied screws to directly

attach the 5-inch dome adapter plate to the ceiling or wall,
with the gasket between the adapter plate and the
mounting surface.

• With a 4S Box: Use your own screws to attach the

adapter plate to the 4S box, which is already installed in
the ceiling or wall, with the gasket between the adapter
plate and the mounting surface.

3. Connect the wires. Refer to the HD3 equIP Series Quick
Install Guide or User Guide for instructions about connecting
the wires.

4. Secure the HD3 equIP Series camera assembly to the 5-inch
dome adapter plate by inserting it into the 5-inch dome
adapter plate then twisting it clockwise until it clicks securely
into place.

5. Adjust the camera field of view. Refer to the HD3 equIP
Series Camera Quick Install Guide or User Guide for
instructions about adjusting the camera Field of View.

6. Install the 5-inch dome bubble:

Note Before installing the 5-inch dome bubble that you have set

aside from your KD5 camera, ensure that the dome liner is
still installed.

a. Slip the looped end of the safety lanyard on the 5-inch

dome bubble onto the safety lanyard hook on the 5-inch
dome adapter plate. (See the other side of this
document for an illustration of the 5-inch dome adapter
plate.)

b. Install the 5-inch dome bubble by placing it on the

5-inch dome adapter plate with the tabs to the left of the
slots, then rotating it clockwise until the locking tab
clicks securely into place.

TM

Series Indoor Fixed Mini Dome

Document 800-06519 – Rev C – 02/2014

Installing a 5-inch Dome Bubble on your HD3 equIP Series camera

Screw holes

Attach camera

assembly

4 tabs

Safety lanyard hook

Attach 5-inch dome bubble
3 tabs

5-Inch Dome Adapter Plate

Locking tab

You can install a 5-inch dome bubble (that you have
purchased separately) on your HD3 equIP Series camera so
that the 3-inch camera matches your existing 5-inch dome
cameras.

1. Install the 5-inch dome adapter plate:

• Without a 4S Box: Use the supplied screws to

directly attach the 5-inch dome adapter plate to the
ceiling or wall, with the gasket between the adapter
plate and the mounting surface.

• With a 4S Box: Use your own screws to attach the

adapter plate to the 4S box, which is already
installed in the ceiling or wall, with the gasket
between the adapter plate and the mounting surface.

2. Connect the wires. Refer to the HD3 equIP Series Quick
Install Guide or User Guide for instructions about
connecting the wires.

3. Secure the HD3 equIP Series camera assembly to the
5-inch dome adapter plate by inserting it into the 5-inch
dome adapter plate then twisting it clockwise until it
clicks securely into place.

4. Adjust the camera field of view. Refer to the HD3 equIP
Series Camera Quick Install Guide or User Guide for
instructions about adjusting the camera Field of View.

5. Install the 5-inch dome bubble (that you have purchased separately):

a. Slip the looped end of the safety lanyard on the 5-inch dome bubble onto the

safety lanyard hook on the 5-inch dome adapter plate.

b. Install the 5-inch dome bubble by placing it on the 5-inch dome adapter plate

with the tabs to the left of the slots, then rotating it clockwise until the locking
tab clicks securely into place.

© 2014 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell. The information in this publication is believed to be accur ate in all re spects. However, Honeywell cannot
assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change
without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

https://www.honeywellsystems.com/ss/techsupp/index.html

www.honeywell.com/security

[phone] (North America only)

Document 800-06519 – Rev C – 02/2014