Honeywell H4L6GR2, HM4L8GR1, HBL6GR2, HMBL8GR1 User Manual

Download

Page 1

equIP® Series Cameras

ULTRA HD IP CAMERA H4L6GR2/ HBL6GR2 /HM4L8GR1/HMBL8GR1

USER GUIDE

Page 2

Page 3

Revisions

Issue Date Revisions

A 07/2017 New document.

Page 4

Cautions and Warnings

CAUTION To ensure compliance with electrical safety standards, CSA

Certified/UL Listed LPS or Class 2 power adapters are required. Power over Ethernet (PoE) shall be provided by listed information technology equipment meeting the IEEE 802.3af PoE standard. The PoE is not intended to be connected to exposed (outside plant) networks.

CAUTION To comply with EN50130-4 requirements, a UPS should be

employed when powering on the camera from 24 V AC.

CAUTION Installation and servicing should be performed only by

qualified and experienced technicians to conform to all local codes and to maintain your warranty.

CAUTION This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may be required to take adequate measures. Note: Only for H4L6GR2, HM4L8GR1 and HMBL8GR1.

Regulatory Statements

FCC Compliance Statement

Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Note Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Canadian Compliance Statement

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.

Page 5

Manufacturer’s Declaration of Conformity

North America

The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-1-07.

Europe

The manufacturer declares that the equipment supplied is compliant with the European Parliament and Council Directive on the Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (2011/65/EU), General Product Safety Directive (2001/95/EC), and the essential requirements the EMC directive 2014/30/EU, conforming to the requirements of standards EN 55032 for emissions, EN 50130-4 for immunity, and EN 60950-1 for electrical equipment safety and EN 50581 for RoHS.

Waste Electrical and Electronic Equipment (WEEE)

Correct Disposal of this Product (applicable in the European Union and other European countries with separate collection systems).

This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.

Safety Instructions

Before installing or operating the unit, read and follow all instructions. After installation, retain the safety and operating instructions for future reference.

1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.

2. INSTALLATION

• Install in accordance with the manufacturer’s instructions.

• Installation and servicing should be performed only by qualified and experienced

technicians to conform to all local codes and to maintain your warranty.

• Do not install the unit in an extremely hot or humid location, or in a place subject to

dust or mechanical vibration. The unit is not designed to be waterproof. Exposure to rain or water may damage the unit.

• Any wall or ceiling mounting of the product should follow the manufacturer’s

instructions and use a mounting kit approved or recommended by the manufacturer.

3. POWER SOURCES - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your facility, consult your product dealer or local power company.

4. HEAT - Situate away from item s that produce heat or are heat sources such as radiators, heat registers, stoves, or other products (including amplifiers).

5. WATER AND MOISTURE - (Indoor models only) Do not use this unit near water or in an unprotected outdoor installation, or any area classified as a wet location.

iii

Page 6

6. MOUNTING SYSTEM - Use only with a mounting system recommended by the manufacturer, or sold with the product.

7. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as they may result in the risk of fire, electric shock, or injury to persons.

8. ACCESSORIES - Only use accessories specified by the manufacturer.

9. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

10. SERVICING - Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

11. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. Using replacement parts or accessories other than the original manufacturers may invalidate the warranty.

12. DAMAGE REQUIRING SERVICE - Unplug the unit from the outlet and refer servicing to qualified service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the unit.

• If the unit has been exposed to rain or water.

• If the unit does not operate normally by following the operating instructions. Adjust

only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.

• If the unit has been dropped or the enclosure has been damage d.

• When the unit exhibits a distinct change in performance - this indicates a need for

service.

13. SAFETY CHECK - Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

Warranty and Service

Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid.

In the event you have a problem with any Honeywell product, please call Customer Service at

1.800.323.4576 for assistance or to request a Return Merchandise Authorization (RMA)

number. Be sure to have the model number, serial number, and the nature of the problem available for the technical service representative.

Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to

Honeywell without a clearly identified Return Merchandise Authorization (RMA) number may be refused.

Page 7

List of Symbols

The following table contains a list of symbols that may appear on the camera:

Symbol Explanation

The WEEE symbol.

This symbol indicates that when the end-user wishes to discard this product, it must be sent to separate collection facilities for recovery and recycling. By separating this product from other household-type waste, the volume of waste sent to incinerators or landfills will be reduced, and thus natural resources will be conserved.

The UL compliance logo.

This logo indicates that the product has been tested and is listed by UL (formerly Und erwriters Laboratories).

The FCC compliance logo.

This logo indicates that the product conforms to Federal Communications Commission compliance standards.

The direct current symbol.

This symbol indicates that the power input/output for the product is direct current.

The alternating current symbol.

This symbol indicates that the power input/output for the product is alternating current.

The RCM compliance logo.

This logo indicates that the product conforms with Australian RCM guidelines.

The CE compliance logo.

This logo indicates that the product conforms to the relevant guidelines/standards for the European Union harmonization legislation.

The caution symbol.

This symbol indicates important information.

The protective earth (ground) symbol.

This symbol indicates that the marked terminal is intended for connection to the protective earth/grounding conductor.

Page 8

Table of Contents

About This Document .......................................................................................................................................................................1

Overview of Contents .................................................................................................................................................................................. 1

Related Documents ..................................................................................................................................................................................... 2

1. Accessing the Camera ...........................................................................................................................................................3

Installing the IPC Tool Utility ................................................................................................................................................................... 3

Discovering Your Camera on the Network ....................................................................................................................................... 3

Assigning a New IP Address to Your Camera .................................................................................................................................. 4

Upgrading the Camera’s Firmware ...................................................................................................................................................... 4

Accessing the Camera from a Web Browser .................................................................................................................................... 5

2. Logging In and Viewing Live Video ...................................................................................................................................6

Logging In to the Web Client................................................................................................................................................................... 6

Overview of the Live Interface ................................................................................................................................................................. 7

Configuring the Live Interface ................................................................................................................................................................ 8

Working in the Live Interface................................................................................................................................................................... 9

Setting Up Live Video Streaming ....................................................................................................................................................... 10

Setting the Stream Type Setting the Stream Protocol

Logging Out of the Web Client ............................................................................................................................................................ 10

3. Playing Back Recorded Video........................................................................................................................................... 11

Overview of the Playback Interface ................................................................................................................................................... 11

Playback Controls Video Clip Controls Timeline

Playing Back Recorded Video .............................................................................................................................................................. 13

Downloading Recorded Video ............................................................................................................................................................. 14

Viewing Snapshots .................................................................................................................................................................................... 15

4. Configuring Video and Audio Settings.......................................................................................................................... 16

Configuring Video Settings ................................................................................................................................................................... 16

Configuring Camera Settings Managing Profiles Configuri ng Streaming Settings Configuri ng Snapshot Settings Configuring Privacy Masks Configuri ng the Cha nnel Title Configuring the Time Title Configuri ng Customized Text Overlays Configuring Picture Overlays Configuri ng Regions of Interest Configuri ng Zoom and Focus Settings

Configuring Audio Settings................................................................................................................................................................... 26

5. Configuring Network Settings ......................................................................................................................................... 27

Configuring TCP/IP .................................................................................................................................................................................. 28

IPv4 Address Configuration IPv6 Address Configuration ARP/Ping

Configuring Network Connections.................................................................................................................................................... 30

Configuring ONVIF .................................................................................................................................................................................... 31

Configuring PPPoE Settings ................................................................................................................................................................ 31

Configuring DDNS Settings.................................................................................................................................................................. 32

Filtering IP/MAC Addresses.................................................................................................................................................................. 33

Adding IP/Mac Addresses to the List of Approved Users Editing IP/Mac Addresses Deleting IP/Mac Addresses from the List of Approved Users

Configuring Email Settings ................................................................................................................................................................... 35

................................................................................................................................................................................................... 13

................................................................................................................................................................................................. 29

..................................................................................................................................................................... 10

.............................................................................................................................................................. 10

................................................................................................................................................................................. 12

............................................................................................................................................................................... 12

........................................................................................................................................................... 16

................................................................................................................................................................................ 19

...................................................................................................................................................... 19

........................................................................................................................................................ 21

................................................................................................................................................................ 22

.......................................................................................................................................................... 23

................................................................................................................................................................. 23

......................................................................................................................................... 24

............................................................................................................................................................ 24

....................................................................................................................................................... 24

.......................................................................................................................................... 25

.............................................................................................................................................................. 28

.............................................................................................................................................................. 29

........................................................................................................ 33

................................................................................................................................................................. 34

................................................................................................ 34

Page 9

Configuring UPnP Port Mapping ....................................................................................................................................................... 36

Configuring SNMP Settings ................................................................................................................................................................. 37

Configuring Bonjour ................................................................................................................................................................................. 37

Configuring Multicast Settings........................................................................................................................................................... 38

Configuring 802.1X Settings ............................................................................................................................................................... 38

Configuring QoS Settings ...................................................................................................................................................................... 39

Working with Certificates ....................................................................................................................................................................... 39

6. Configuring Event Settings .............................................................................................................................................. 41

Configuring Alarm Events ...................................................................................................................................................................... 41

Configuring System Events .................................................................................................................................................................. 43

Configuri ng SD Card Event Settings Configuri ng Network Event Setti ngs Configuri ng Illegal Access Event Settings

Configuring Motion Detection Events ............................................................................................................................................ 45

Configuring Camera Tampering Events ......................................................................................................................................... 47

Configuring Scene Change Events ................................................................................................................................................... 48

Configuring Audio Events ...................................................................................................................................................................... 49

Accessing Extensional Smart Function .......................................................................................................................................... 50

Configuring Face Detection Events.................................................................................................................................................. 52

Configuring People Counting Events .............................................................................................................................................. 53

People Counting................................................................................................................................................................................ 53

Report ..................................................................................................................................................................................................... 53

7. Configuring Recording Settings ..................................................................................................................................... 55

Configuring Recording Schedules .................................................................................................................................................... 55

Configuring Storage Settings .............................................................................................................................................................. 56

Configuri ng Storage Paths Configuring the Local SD Card for Storage Configuri ng an FTP Server for Storage Configuri ng an NAS Disk for St orage

8. Configuring System Settings ........................................................................................................................................... 60

Configure Multi Sensor ........................................................................................................................................................................... 62

9. Technical Specifications .................................................................................................................................................... 73

................................................................................................................................................................ 57

.............................................................................................................................................. 43

.................................................................................................................................... 44

.................................................................................................................................. 57

.......................................................................................................................................... 58

............................................................................................................................................. 58

vii

Page 10

Page 11

About This Document

This manual is intended for system installers, administrators, and users of Honeywell’s equIP® Series 4K Ultra HD network cameras and contains instructions for accessing, configuring, and operating the cameras.

Overview of Contents

This manual contains the following chapters and appendixes:

• Chapter 1, Accessing the Camera, describes how to access the camera remotely from a

web browser.

• Chapter 2, Logging In and Viewing Live Video, describes how to log in to the camera and

how to use the Live interface.

• Chapter 3, Playing Back Recorded Video, describes how to play back and export recorded video and snapshots.

• Chapter 4, Configuring Video and Audio Settings, describes how to set up video and audio streams.

• Chapter 5, Configuring Network Settings, describes how to set up the camera on a

network. (For advanced users only.)

• Chapter 6, Configuring Event Settings, provides instructions for configuring alarm

inputs/outputs, motion detection, audio detection, tampering detection, and system event settings.

• Chapter 7, Configuring Recording Settings, describes how to set up a recording

schedule and how to manage recording and storage settings.

• Chapter 8, Configuring System Settings, provides instructions for configuring language

and date and time options, managing user accounts and permissions, setting maintenance tasks, upgrading firmware, and resetting a came ra to its factory defaults.

• Chapter 9 Technical Specifications, lists camera specifications.

• Index, provides a searchable list of key terms used in the manual.

About This Document

Page 12

ULTRA HD IP Camera User Guide

Installation Guide

You can find these and other documents on the product webpages:

1. Accessing the Camera

This chapter contains the following sections:

• Installing the IPC Tool Utility, page 3

• Discovering Your Camera on the Network, page 3

• Assigning a New IP Address to Your Camera, page 4

• Upgrading the Camera’s Firmware, page 4

• Accessing the Camera from a Web Browser, page 5

Installing the IPC Tool Utility

To install the IPC Tool utility and create a desktop shortcut:

1. Insert the included Software and Document disc into your PC’s disc drive.

2. Install the IPC Tool utility to your PC. The shortcut is added to the desktop.

Accessing the Camera

Discovering Your Camera on the Network

To discover your network camera(s), open the IPC Tool utility , enter your user name and password, and then click Connect. Cameras that are online have a green connected icon

next to them. Cameras that are offline have a gray X next to them. To refresh the list, click Refresh.

Page 14

Ultra HD IP Camera User Guide

Assigning a New IP Address to Your Camera

The current IP address of your camera appears in the IP column of the devices list. If you want, you can assign a new static IP address to the camera.

To change the IP address of a single camera:

1. Select the camera that you want to configure from the devices list.

2. Click the Network tab.

3. Clear the DHCP check box.

4. Enter the new IP settings in the IP Address, Subnet Mask, and Default Gateway fields.

5. Click Apply to apply the settings.

To change the IP addresses of multiple cameras at the same time:

1. In the left-most pane of the IPC Tool utility, click Batch Setting.

2. Select all of the cameras that you want to configure from the devices list.

3. Click the Network tab.

4. Do one of the following:

• To assign dynamic IP addresses, select the Set all to DHCP check box, and then

click Apply.

• To assign static IP addresses, enter the settings in IP Range, Subnet Mask, and

Default Gateway fields, and then click Apply.

Upgrading the Camera’s Firmware

Before you begin using your camera, make sure you have the latest firmware installed. You can upgrade a single camera or multiple cameras at the same time.

To upgrade a single camera:

1. Select the camera that you want to upgrade from the devices list.

2. Click the Upgrade tab.

3. Click Browse, navigate to the directory that contains the firmware file (.bin), select the file, and then click Open. The firmware file appears in the Target File field.

4. Click Upgrade. When the upgrade is complete, the camera will reboot.

To upgrade multiple cameras at the same time:

1. In the left-most pane of the IPC Tool utility, click Batch Setting.

2. Select all of the cameras that you want to upgrade from the devices list.

3. Click the Upgrade tab.

4. Click Browse, navigate to the directory that contains the firmware file (.bin), select the file, and then click Open. The firmware file appears in the Target File field.

5. Click Upgrade. When the upgrade is complete, the cameras will reboot.

Page 15

Accessing the Camera from a Web Browser

To access the camera from a web browser:

1. Select the camera that you want to access from the devices list. The camera must be online .

2. On the Device Information tab, click Web Page. The web client opens in your default browser.

Accessing the Camera

Page 16

Ultra HD IP Camera User Guide

2. Logging In and Viewing Live Video

This chapter contains the following sections:

• Logging In to the Web Client, page 6

• Overview of the Live Interface, page 7

• Configuring the Live Interface, page 8

• Working in the Live Interface, page 9

• Logging Out of the Web Client, page 10

Logging In to the Web Client

If this is your first time logging in to the web client, on the login page, enter the default user name (admin) and password (1234), and then click Login.

Page 17

For security purposes, we strongly recommend that you create a new secure password.

The password must be at least 8 characters long and contain at least one lowercase letter, one number, and one special character. The password cannot be blank.

Overview of the Live Interface

Figure 2-1 shows the layout of the web client’s Live interface.

Figure 2-1 Live Interface

Logging In and Viewing Live Video

Page 18

Ultra HD IP Camera User Guide

Configuring the Live Interface

Note The first time you log into the web client, follow the on-screen instructions to

You can configure the Live interface using the configuration controls located in the lower left corner of the screen, immediately below the video window (Figure 2-2).

Figure 2-2 Live Configuration Toolbar

Table 2-1 Live Configuration Controls

Image

Original Size Displays the video at actual size (the exact dimensions are

download and install the web browser plug-in.

Opens the Image Adjustment panel.

Adjustment

Move the sliders to adjust the image brightness, contrast, hue, or saturation. Click the – and + signs to make fine adjustments. To restore the settings to their default values (64), click Reset.

Note These settings only apply to the

determined by the stream resolution).

client end. To change the settings at the camera end, go to Setup > Camera Setup > Conditions > Picture.

Full Screen

Width:Height Ratio

Displays the video in full-screen mode. Double-click (or press Esc) to exit full-screen mode.

Displays the video in its original size (Original) or fitted to your screen (Adaptive).

Fluency Sets the video fluency level (Realtime, Normal, or Fluency).

Select a fluency level based on the capabilities of your network. For example, if your connection is slow, selecting Fluency will prioritize smoothness over image quality.

Rules Info Tracks movement in the video window when intelligent video

surveillance (IVS) is enabled.

Zoom and Focus Note: Only for H4L6GR2 and HBL6GR2.

Opens the Zoom and Focus panel.

Move the sliders to adjust the zoom and focus settings. Click the – and + signs to make fine adjustments. The Step number determines the magnitude of the adjustment. To set the focus automatically, click Auto Focus. To restore the default zoom and focus settings, click Restore All. To focus on a specific region, click Regional Focus, and then drag your mouse over the area in the video window.

Page 19

Help

Displays online help for the Live interface.

Snapshot

Click to take a snapshot of the current video. The snapshot is saved to the location specified in Setup > Storage Setup >

Audio

Click to enable or disable the audio input stream.

Talk

Click to enable or disable bidirectional talk (audio must also be enabled).

Alarm Output

Click to generate or cancel an alarm output. The icon appears red when the alarm is active, gray when the alarm is inactive.

Working in the Live Interface

The toolbar in the upper left corner of the screen, immediately above the video window, provides quick access to commonly used controls (Figure 2-3).

Figure 2-3 Quick Access Toolbar

Table 2-2 Quick Access Controls

Logging In and Viewing Live Video

Easy Focus Note: Only for H4L6GR2 and HBL6GR2.

Displays the current video definition (AF Peak) and target video

definition (AF Max). For auto focus to work, the AF Peak and AF Max values must be close together. If the values are far apart, the camera must be re-aime d or focused manually.

Record Click to start or stop recording video. The icon appears red when

video is being recorded, gray when video is not being recorded. The recorded video is saved to the location specified in Setup >

Storage Setup > Destination > Path > Live Record.

Triple Snapshot Click to take three snapshots in quick succession (1 per

second). The snapshots are saved to the location specified in

Setup > Storage Setup > Destination > Path > Live Snapshot.

Destination > Path > Live Snapshot.

Digital Zoom When this function is enabled, you can drag your mouse over an

area of the video to enlarge that area. Right-click to return to the previous magnification.

Page 20

Ultra HD IP Camera User Guide

Setting Up Live Video Streaming

In the upper right corner of the screen, immediately above the video window, you can set the stream type and protocol for live video streaming.

Setting the Stream Type

To set the stream type, in the Stream Type list, select Main Stream, Sub Stream 1, or Sub Stream 2.

Main Stream Delivers high definition video for real-time monitoring, recording, and storage.

Sub Stream 1 Delivers low/standard definition video, typically for remote monitoring in lower

Sub Stream 2 Delivers low, standard, or high definition video.

The properties for each stream type are configured on the Setup > Compression Setup > Video page (see Configuring Streaming Settings on page 19).

Setting the Stream Protocol

Uses the most bandwidth.

network bandwidth environments.

To set the stream protocol, in the Protocol list, select TCP, UDP, or Multicast.

TCP Provides most reliable data transmission. Higher latency and bandwidth use

than UDP.

UDP Provides fastest data transmission. Lower latency and bandwidth use than

TCP but allows some data loss (such as dropped frames).

Multicast Provides the most efficient use of bandwidth if large numbers of clients are

viewing the video simultaneously.

Logging Out of the Web Client

To log out of the web client, in the upper right corner of the screen, click Logout.

Page 21

Playing Back Recorded Video

3. Playing Back Recorded Video

This chapter contains the following sections:

• Overview of the Playback Interface, page 11

• Playing Back Recorded Video, page 13

• Downloading Recorded Video, page 14

• Viewing Snapshots, page 15

Overview of the Playback Interface

Figure 3-1 shows the layout of the web client’s Playback interface.

Figure 3-1 Playback Interface

Page 22

Ultra HD IP Camera User Guide

Play/Pause

Click to play recorded video.

Pause

Click to pause playback.

Stop

Click to stop playback.

Next Frame

Click to advance to the next frame when playback is paused.

Slow Play

Click to slow down playback.

Fast Play

Click to speed up playback.

Volume

Click to enable sound.

Mute

Click to disable sound.

Volume Level Drag the slider to adjust the sound volume.

Playback Controls

The playback controls are located in the lower left corner of the screen, immediately below the video window. For instructions on how to play back video, see Playing Back Recorded

Video on page 13.

Figure 3-2 Playback Toolbar

Table 3-1 Playback Controls

Video Clip Controls

The video clip controls are located in the lower right corner of the screen, immediately below the file list button. For instructions on how to create and export a video clip, see Downloading

Recorded Video on page 14.

Figure 3-3 Video Clip Area

Table 3-2 Video Clip Controls

Clip Click to start/stop clipping video.

Download Click to download the video clip that you have created to a local

drive on your PC.

Page 23

Timeline

Playing Back Recorded Video

The timeline is located below the playback and video clip controls.

Figure 3-4 Timeline Area

Table 3-3 Timeline Controls

General Displays video saved during normally scheduled recording in the

timeline.

Motion Displays video saved during a motion detection event in the

Record

Type

Alarm Displays video saved during an alarm event in the timeline.

timeline.

Manual Displays video saved manually during live monitoring in the

timeline.

24hr Displays 24 hours of video in the timeline.

2hr Displays 2 hours of video in the timeline.

1hr Displays 1 hour of video in the timeline.

30min Displays 30 minutes of video in the timeline.

Playing Back Recorded Video

To play back recorded video:

1. From the File Type list, select dav.

2. From the Data Src list, select the location where the video files are stored.

The storage location is configured in Setup > Storage Setup > Destination (see Configuring Storage Settings on page 56).

3. Locate the file that you want to play back.

a. Above the calendar, select the month and year that

you want to search.

b. On the calendar, click the date that you want to

search. Recordings for the selected date appear in the timeline (color coded according to recording type).

c. Below the calendar, click the File List button to

narrow your search by time period and/or by download format.

Page 24

Ultra HD IP Camera User Guide

4. Play the file using one of the following methods:

• In the file list, double-click the file that you want to play.

• In the timeline, click a colored bar at the time that you want to start playing from

(click to zoom in on the timeline), and then click the Play button.

Downloading Recorded Video

There are two ways to download recorded video: you can download a complete video file (the maximum length is specified in Setup > Storage Setup > Record Control) or you can create and export a video clip that you have created.

To download a video file:

1. From the File Type list, select dav.

2. From the Data Src list, select the location where the video files are stored.

3. On the calendar, click the date that the video was recorded.

4. Click File List to display the list of video files for that date.

5. Set the Download Format to dav or mp4.

6. From the file list, click the download button of the file that you want to download.

The button changes to and the file is saved to the location specified in Setup >

Compression Setup > Path > Playback Download.

To create and export a video clip:

1. Open a video file in the playback window.

2. Pause the video at the time when you want to start the clip.

3. In the video clip area, click the Select Start Time button .

4. Resume playing the video.

5. Pause the video at the time when you want to stop the clip.

6. Click the Select Stop Time button .

7. Stop the video, and then click the Download button .

Note You cannot download the clip while the video file is still open in the web client.

The clip is saved to the location specified in Setup > Compression Setup > Path > Video Clips.

Page 25

Viewing Snapshots

You can take snapshots of video during playback by clicking the Snapshot button . The snapshot is saved to the location specified in Setup > Compression Setup > Path > Playback

Snapshot.

To view a snapshot that you have saved manually during live monitoring, go the directory specified in Setup > Compression Setup > Path > Live Snapshot and double-click the file to open it.

To view a snapshot that you have saved manually during playback, go the directory specified in Setup > Compression Setup > Path > Playback Snapshot and double-click the file to open it.

If you have configured the system to take snapshots on a schedule, or during motion detection or alarm events, you can view and download them.

To view or download a system-generated snapshot:

1. From the File Type list, select jpg.

2. From the Data Src list, select the location where the snapshot files are stored.

3. On the calendar, click the date that the snapshot was taken.

4. Click File List to display the list of snapshots for that date.

5. Double-click the snapshot file that you want to view. The file opens in the video window.

6. To download the file, click the download button . The file opens in a new browser window. Right-click the image and then click Save picture as or Save image as to save the snapshot to a local directory.

Playing Back Recorded Video

Page 26

Ultra HD IP Camera User Guide

4. Configuring Video and Audio Settings

This chapters contains the following sections:

• Configuring Video Settings, page 16

• Configuring Audio Settings, page 26

Configuring Video Settings

This section describes how to configure camera properties (picture, exposure, lighting compensation, white balance, day and night, IR light, and defog) and video streaming properties (format, resolution, frame rate, bit rate, and I-frame interval).

Configuring Camera Settings

You can configure camera properties on the Setup > Camera Setup > Properties page.

Profile

In the Profile box, select the camera profile that you want to configure settings for: Normal, Day, or Night.

Picture

In the Picture area, you can manually adjust the image brightness, contrast, saturation, sharpness, and gamma levels.

Drag the slider left or right to decrease or increase the value.

Click the – and + signs to make fine adjustments.

Brightness Adjusts the black level of the image.

Contrast Adjusts the white level of the image.

Saturation Adjusts the intensity of the image colors.

Sharpness Adjusts the edge sharpness of image elements. Keep in mind that increasing

sharpness in a moving image will create more noise, resulting in a larger bit stream and saved file size.

Gamma Adjusts the amount of gamma correction applied to the image. Use fine

adjustments to accent darker areas of the image.

Page 27

Configuring Video and Audio Settings

You can also change the image orientation (Note: Only for H4L6GR2 and HBL6GR2.):

• To reverse the image, set Mirror to ON.

• To rotate the image 90 degrees, 180 degrees, or 270 degrees, set AOV to 90° (Flip Mode

1), 180° Inverted, or 270° (Flip Mode 2) respectively.

If the camera is mounted on a pole or in an environment subject to vibration, you can set EIS (Electronic Image Stabilization) to ON to improve image stability.

Note: only for H4L6GR2 and HBL6GR2.

Click Save to apply the settings.

Exposure

In the Exposure area, you can set the anti-flicker mode, exposure mode, auto iris, and digital noise reduction level.

Set Anti-Flicker to Outdoor, 50Hz, or 60Hz.

Outdoor Minimizes flicker in outdoor applications. Works with auto, low noise, low motion

50Hz Minimizes flicker in indoor applications where the AC frequency is 50 Hz

60Hz Minimizes flicker in indoor applications where the AC frequency is 60 Hz

blur, and manual exposure modes

(generally PAL regions). Works with auto and manual exposure modes.

(generally NTSC regions). Works with auto and manual exposure modes.

Set Mode to Auto, Gain Priority, Shutter Priority, Iris Priority, or Manual.

Auto Exposure settings change automatically with changes in the scene's

lighting.

Gain Priority The shutter speed and iris are adjusted automatically for the specified gain

value.

Shutter Priority The iris and gain are adjusted automatically for the specified shutter speed.

Iris Priority The shutter speed and gain are adjusted automatically for the specified iris

value.

Manual Maximum shutter speed and maximum gain for normal light conditions are

set by the user.

3DNR (3D noise reduction) is enabled by default. Drag the Grade slider left or right to decrease or increase the level of digital noise reduction applied to the image. To disable 3D noise reduction, set 3DNR to OFF.

Click Save to apply the settings.

Lighting Compensation

In the Lighting Compensation area, you can apply backlight compensation (BLC), highlight compensation (HLC), digital wide dynamic range (DWDR), or smart scene adaptive (SSA) adjustment to the image.

Set Lighting Mode to OFF, BLC, HLC, DWDR, or SSA.

BLC Corrects the exposure of strongly backlit scenes. To apply BLC to the entire scene,

click Default. To apply BLC to a specific area of the scene, click Customized. A yellow rectangle appears in the preview window. To move it, drag the center of the frame. To resize it, drag one of the corner handles.

HLC Masks strong light sources in the scene. Drag the slider to adjust the HLC level.

Click the – and + signs to make fine adjustments.

Page 28

Ultra HD IP Camera User Guide

DWDR Corrects the exposure of overexposed and underexposed areas of the scene. Drag

the slider to adjust the DWDR level. Click the – and + signs to make fine adjustments.

SSA Automatically decreases the brightness of bright areas and increases the

brightness of dark areas according to the environmental lighting. Note: only for H4L6GR2 and HBL6GR2.

Click Save to apply the settings.

White Balance

White balance compensates for the different color temperatures of different light sources, ensuring consistent colors- in the image.

In the White Balance area, you can set the white balance mode to Auto, Natural, Street

Lamp, Outdoor, Manual or Customize Region.

Auto White balance is adjusted automatically.

Natural White balance is optimized for natural lighting.

Street Lamp White balance is optimized for yellow-tinted lighting.

Outdoor White balance is optimized for outdoor environments.

Manual Red gain and blue gain values are set by the user.

Customize Region White balance is applied to a user-defined area within the scene.

Click Save to apply the settings.

Day and Night

In the D&N Mode area, you can set the day and night mode, sensitivity, and delay time.

By default, the camera automatically outputs color video or black-and-white video depending on the amount of light in the scene. To output only color video, set Mode to Color. To output only black-and-white video, set Mode to Black & White.

Sensitivity controls the sensitivity to lighting changes that cause the camera to switch between day (color) and night (black-and-white) mode. Select Low, Medium, or High.

Delay defines the delay time before switching between modes. Select a value between 2s and 10s.

Click Save to apply the settings.

IR Light

In the IR Light area, you can set the infrared LED mode and other settings.

Set Mode to Manual, Zoom Priority, Smart IR, or OFF.

Manual：IR near and far distance brightness are set by the user.

Zoom Priority

Smart IR

If Mode is set to Manual, set the infrared LED brightness level. Drag the slider left or right to decrease or increase the value. Click the – and + signs to make fine adjustments.

：IR setti ngs are adjusted automatically based on the zoom setting. Note: only for H4L6GR2

and HBL6GR2.

：IR settings are adjusted automatically to prevent overexposure or underexposure.

If Mode is set to Zoom Priority, set the IR Correction level to correct focusing problems caused by bright IR light.

Note: only for H4L6GR2 and HBL6GR2.

Page 29

Defog

Configuring Video and Audio Settings

To enable the defog function, set Mode to OFF, Manual, or Auto .

If Mode is set to Manual, do the following:

1. Set Intensity to Low, Medium, or High.

2. Set Airlight Mode to Auto or Manual.

Click Save to apply the settings. Note: only for H4L6GR2 and HBL6GR2.

Managing Profiles

After you have configured the camera properties for each profile (Normal, Day, Night), you can set the profile(s) that you want the system to use on the Setup > Camera Setup > Profile

Management page.

Auto The defog function is enabled automatically when the scene is obscured by fog or

haze.

Manual The defog function is always enabled.

Auto The defog function is fine-tuned automatically (recommended).

Manual The defog function is fine-tuned by the user using the Grade slider.

Next to Profile Management, select Normal, Full Time, or Schedule. By default, the system has the Day profile always enabled.

Normal The Normal profile is always enabled.

Full Time The Day profile or Night profile is always enabled, depending on your selection.

Schedule The system switches between the Day profile and Night profile. Drag the sliders on

the left and right sides of the timeline to set the Night-to-Day and Day-to-Night switching times.

Click Save to apply the settings.

Configuring Streaming Settings

You can configure video streaming properties on the Setup > Compression Setup > Video page.

The page is divided into two sections: Main Stream and Sub Stream. In the Sub Stream section, two sub streams are configurable: Sub Stream 1 and Sub Stream 2. To enable a sub stream, select one of the sub streams, and then select the Enable check box.

Page 30

Ultra HD IP Camera User Guide

For each record type (General, Motion, Alarm), you can configure the encoding format, resolution, frame rate, bit rate, and I-frame interval settings. You can also apply a custom watermark to the main stream.

Format

H.264

H.264B Baseline Profile. Uses up to 50% less bandwidth than MPEG4 and up to 80% less

H.264H High Profile. Uses less bandwidth than Main Profile at the same quality. Lower

MJPEG Uses the most bandwidth but produces excellent image quality with access to

H.265

Main Profile. Uses less bandwidth than Baseline Profile at the same quality.

than MJPEG. Higher compression and lower quality than H.264.

compression and higher quality than H.264.

every image in the stream.

High Efficiency Video Coding. Supports 4K resolution. Twice as efficient as H.264.

Smart Codec

Set Smart Codec to ON or OFF.

By taking reference frames and applying them to refreshed frames, Smart Codec eliminates the need to transmit data for an unchanged image or parts of the image where there is no movement. Used together with H.264, Smart Codec can lead to storage savings of up to 60 percent and bandwidth savings of up to 40 percent over H.264 alone.

In the Format box, select H.264B, H.264, H.264H, MJPEG, or H.265.

Page 31

Configuring Video and Audio Settings

Resolution

In the Resolution box, select a resolution from the list. The available options differ between the main stream and sub streams.

Frame Rate

In the Frame Rate (FPS) box, select a frame rate within the available range (1–30 fps for NTSC cameras; 1–25 fps for PAL cameras).

Note

Only 1-25fps can be selected for main resolution of HM4L8GR1 and HMBL8GR1 in NTSC mode.

Bit Rate

In the Bit Rate Type box, select CBR or VB R.

CBR Constant bit rate. The bit rate remains constant (recommended for

low-bandwidth environments). Required if MJPEG compression is used.

VBR Variable bit rate. The bit rate changes according to the complexity of the scene.

Select a Quality level between 1 (lowest quality) and 6 (highest quality).

In the Bit Rate box, select a bit rate from the list using the Reference Bit Rate as a guide.

I-Frame Interval

In the I-Frame Interval box, enter a value between 1 and 150. The default I-frame interval is two times the frame rate. For example, if the frame rate is 30 fps, the I-frame interval will be 60.

Watermark

To apply a custom watermark to the main stream, select the Watermark Settings check box. In the Watermark Text box, enter the watermark text. The text cannot have any spaces but underscores (_), and hyphens (-) are acceptable.

Click Save to apply the settings.

Configuring Snapshot Settings

You can configure snapshot properties on the Setup > Compression Setup > Snapshot page.

Snapshot Type

Set the Snapshot Type to General or Event.

General Snapshots are taken according to a user-defined schedule.

Page 32

Ultra HD IP Camera User Guide

Event Snapshots are taken whenever an alarm, motion detection, camera tampering, or

Image Size

The image size is determined by the main stream resolution setting. It is not configurable. (See Resol ution on page 21).

Quality

Set the Quality to a value between 1 (lowest) and 6 (highest).

Interval

Select a snapshot frequency between 1 snapshot per second (1s) and 7 snapshots per second (7s), or click Customized to define a custom setting between 1 and 50,000 seconds.

Click Save to apply the settings.

Configuring Privacy Masks

You can configure privacy mask properties on the Setup > Compression Setup > Overlay > Privacy Masking page.

system event occurs.

To enable privacy masking, click Enable. Four privacy masks appear in the preview window.

Delete any masks that you don’t need. To delete a mask, right-click it or select it and then click Delete. To remove all the masks, click Remove All.

To move a mask, select it and drag the center of the mask.

Page 33

Configuring Video and Audio Settings

To resize a mask, drag one of the corner handles. To draw a new mask, drag your mouse anywhere in the preview window.

Click Save to apply the settings.

Configuring the Channel Title

You can configure the channel title properties on the Setup > Compression Setup > Overlay > Channel Title page.

To display the channel title, click Enable, and then click Save. By default, the channel title appears in the lower left corner of the video image.

To move the channel title, drag the yellow Channel Title box to the desired location in the preview window, and then click Save.

To modify the channel title, enter the new title in the Input Channel Title field, and then click Save.

To hide the channel title, click Disable, and then click Save.

Configuring the Time Title

You can configure the time title properties on the Setup > Compression Setup > Overlay > Time Title page.

To display the channel title, click Enable, and then click Save. By default, the channel title appears in the upper right corner of the video image.

To display the day of the week, select the Show Day of Week check box, and then click Save.

To move the time title, drag the yellow Time Title box to the desired location in the preview window, and then click Save.

To hide the time title, click Disable, and then click Save.

Page 34

Ultra HD IP Camera User Guide

Configuring Customized Text Overlays

You can configure customized text overlays on the Setup > Compression Setup > Overlay > Text Overlay page.

To display the text overly, click Enable, enter the desired text in the Input Text field, and then click Save. By default, the text overlay appears in the lower right corner of the video image.

Set Text Alignment to Left or Right.

To move the text overlay, drag the yellow Text Overlay box to the desired location in the preview window, and then click Save.

To hide the text overlay, click Disable, and then click Save.

Configuring Picture Overlays

You can configure picture overlays on the Setup > Compression

Setup > Overlay > Picture Overlay

page.

To display a picture overlay, click Enable, click Upload Picture, upload the picture, and then click Save. The file must be in BMP format, less than 16 KB, and no more than 128×128 pixels.

To move the picture overlay, drag the yellow frame to the desired location in the preview window, and then click Save.

To hide the picture overlay, click Disable, and then click Save.

Configuring Regions of Interest

You can configure regions of interest (ROI) on the Setup > Compression Setup > ROI page.

To enable the ROI function, click Enable.

In the preview window, drag your mouse over the portion of the scene that you want to designate as a region of interest, select an Image Quality level between 1 (lowest) and 6 (highest), and then click Save. You can add up to 4 regions of interest.

To delete a single region of interest, select it, and then click Delete. To delete all regions of interest, click Remove All.

Page 35

Configuring Video and Audio Settings

Configuring Zoom and Focus Settings

You can configure zoom and focus on the Setup > Zoom and Focus > Zoom and Focus page.

To adjust the zoom magnification, drag the slider right or left. Click the + and - signs to make fine adjustments. The Step number determines the magnitude of the adjustment.

To adjust the focus manually, drag the slider right or left. Click the + and - signs to make fine adjustments. The Step number determines the magnitude of the adjustment.

To set the focus automatically, click Auto Focus.

To restore the default zoom and focus settings, click Restore All.

Note: only for H4L6GR2 and HBL6GR2.

Page 36

Ultra HD IP Camera User Guide

Configuring Audio Settings

You can configure audio settings for Main Stream, Sub Stream 1, and Sub Stream 2 profiles on the Setup > Audio Setup > Audio page.

To enable audio for the stream, select the Enable check box, select the format (G.711A, G.711Mu, G.726, AAC), and then select a sampling frequency (8–64 kHz).

In the Properties area, enable or disable noise filtering, and adjust the microphone and/or speaker volumes by moving the sliders. Click the+ and - signs to make fine adjustments. Click Save to apply the settings.

Page 37

Configuring Network Settings

5. Configuring Network Settings

This chapter contains the following sections:

• Configuring TCP/IP, page 28

• Configuring Network Connections, page 30

• Configuring ONVIF, page 31

• Configuring PPPoE Settings, page 31

• Configuring DDNS Settings, page 32

• Filtering IP/MAC Addresses, page 33

• Configuring Email Settings, page 35

• Configuring UPnP Port Mapping, page 36

• Configuring SNMP Settings, page 37

• Configuring Bonjour, page 37

• Configuring Multicast Settings, page 38

• Configuring 802.1X Settings, page 38

• Configuring QoS Settings, page 39

• Working with Certificates, page 39

Page 38

Ultra HD IP Camera User Guide

Configuring TCP/IP

You can configure TCP/IP settings, including IPv4/IPv6 and ARP/Ping settings, on the Setup > Network Setup > TCP/IP page.

IPv4 Address Configuration

By default, the camera uses IPv4 and obtains IP settings automatically via DHCP.

In the Hostname field, enter a nickname for the camera that can be mapped to the IP address and used to identify the camera.

To manually assign IP address settings, set Mode to Static, and then replace the values in the IP Address, Subnet Mask, and Default Gateway fields.

To manually assign DNS server addresses, replace the values in the Preferred DNS Server and Alternate DNS Server fields.

Click Save to apply the settings.

Page 39

Configuring Network Settings

IPv6 Address Configuration

To enable IPv6, set IP Version to IPv6. Verify that the IP address and default gateway (router) address are in the same network segment. Click Save to apply the settings.

ARP/Ping

You can assign an IP address to the camera using the ARP/Ping service.

To enable ARP/Ping to set the IP address:

1. Obtain an unused IP address in the same LAN as your PC.

2. Write down the MAC address of the camera (it is listed on the label).

3. Select the Enable ARP/Ping check box, and then click Save.

Page 40

Ultra HD IP Camera User Guide

4. Open the Command Prompt window on your PC (in Windows 7, click Start > All Programs > Accessories > Command Prompt) and type the appropriate commands for your operating system:

5. Reboot the camera. If the setup was successful, the Command Prompt window will display “Reply from" and the IP address (for example, "Reply from 192.168.0.125 …”).

To verify that the IP address works, open your browser and type in the address bar http:// followed by the IP address (for example , http://192.168.0.125), then press Enter.

Configuring Network Connections

You can configure network connections and port settings on the Setup > Network Setup > Connection > Connection page.

By default, the maximum number of simultaneous connections the camera will support is set to 10. To change this setting, in the Max Connections field, enter a value between 1 and 20.

If you want, you can change the TCP, UDP, HTTP, RTSP, and HTTPS port numbers from their defaults.

Click Save to apply the settings.

Page 41

Configuring ONVIF

ONVIF (Open Network Video Interface Forum) is a global standard for the interoperability of IP-based physical security products.

You can enable or disable ONVIF authentication on the Setup > Network Setup > Connection > ONVIF page.

ONVIF login authentication is enabled by default. To disable it, next to Login Authentication, click OFF, and then click Save.

Configuring PPPoE Settings

Configuring Network Settings

You can configure Point-to-Point Protocol over Ethernet (PPPoE) settings on the Setup >

Network Setup > PPPoE page.

To enable PPPoE:

1. Select the Enable check box.

2. In the User Name and Password fields, enter the user name and password that you received from your Internet service provider (ISP).

3. Click Save to apply the settings. The camera will connect to the Internet via PPPoE after rebooting.

Page 42

Ultra HD IP Camera User Guide

Configuring DDNS Settings

You can configure Dynamic DNS (DDNS) settings on the Setup > Network Setup > DDNS page.

You can use a DDNS service to track and update your camera’s dynamic IP address, so that even when the numeric IP address changes the DDNS address always remains the same.

To access your camera using a DDNS service:

1. Register an account with a supported DDNS service, such as DynDNS or Honeywell’s free DDNS service (www.hennvr-ddns.com).

2. Select the Server Type check box.

3. Select your DDNS service from the Server Type drop-down list.

4. In the Domain Name field, enter the domain name (hostname) that you registered with the DDNS service (for example, mycamera.dyndns.org).

5. In the User Name and Password fields, enter the user name and password of the account that you registered in step 1.

6. In the Update Period field, enter the interval in minutes between address updates sent to the DDNS server.

Note If you selected Honeywell DDNS as your DDNS service, the domain name is set

to the camera’s MAC address by default and no user name or password are required. Set Mode to Auto or Manual. If you configure the domain name

7. Click Save to apply the settings. You can now access the camera by entering the domain name in your browser’s address bar.

manually, click Test to verify that the domain name is registered.

Page 43

Filtering IP/MAC Addresses

You can configure IP filter settings on the Setup > Network Setup > IP Filter page.

When the IP filter is enabled, remote access to the camera is restricted to specific IP or MAC addresses. You can add or remove addresses from the list at any time. If a user is accessing the camera over a WAN, enter the MAC address of the user's router instead of an IP address.

Adding IP/Mac Addresses to the List of Approved Users

Configuring Network Settings

To add an IP/MAC address:

1. Click Add IP/MAC.

2. In the Add IP/MAC window, select IP Address, IP Segment, or MAC from the drop-down list, enter the relevant address, and then click Save.

The address is added to the list of approved users.

3. Select the Approved Users check box, and then click Save to apply the settings.

Page 44

Ultra HD IP Camera User Guide

Editing IP/Mac Addresses

To edit an IP/MAC address:

1. In Address List, click the Modify icon of the address that you want to edit.

2. In the Modify IP/MAC window, edit the address as needed, and then click Save.

Deleting IP/Mac Addresses from the List of Approved Users

To delete a single IP/MAC address:

1. In the Address List, click the Delete icon of the address that you want to delete.

2. A confirmation message appears. Click OK to continue, and then click Save to apply the settings. The address is removed from the list of approved users.

To delete multiple IP/MAC addresses:

1. Click Remove All.

2. A confirmation message appears. Click OK to continue, and then click Save to apply the settings. All addresses are removed from the list of approved users.

Page 45

Configuring Email Settings

Configuring Network Settings

You can configure email notification settings on the Setup > Network Setup > SMTP page.

To set up email notifications:

1. In the SMTP Server and Port fields, enter the SMTP server and port information.

2. In the User Name and Password fields, enter the sender’s email user name and password. Alternatively, if the server supports anonymous login, you can select the Anonymous check box to log in without a user name and password.

3. In the Sender field, enter the sender’s email address.

4. From the Authentication list, select an encryption mode (SSL or TLS) or select None.

5. In the Title field, enter the text that you want to appear in the subject line of the email.

6. Select the Attachment check box if you want to enable snapshot attachments.

7. In the Mail Receiver field, enter the recipient’s email address, and then click the + sign to add it to the list. You can enter up to three email addresses. To remove an address from the list, select it, and then click the – sign.

8. In the Interval field, specify the interval between email notification messages. Enter a value between 0 (no interval) and 3600 seconds (60 minutes).

Note Setting an interval between email notifications reduces the load on the email

9. To have the system periodically verify that the email notification settings are working, select the Send Health Messages check box, and specify the Interval.

10. Click Save to apply the settings.

11. Click Email Test to send a test email to verify that the settings are configured properly.

server if multiple notifications are triggered simultaneously.

Page 46

Ultra HD IP Camera User Guide

Configuring UPnP Port Mapping

You can configure Universal Plug and Play (UPnP) settings on the Setup > Network Setup > UPnP page.

The UPnP protocol is used to detect network devices with clients running Windows.

To enable UPnP, select the Enable check box. The camera can now be detected by Windows' built-in network browser (My Network Places in Windows XP; Network in Windows 7).

To enable UPnP in Windows XP:

1. Go to Start > Control Panel > Add or remove programs.

2. Click Add or remove programs, then select Networking Services in the Windows Components Wizard.

3. Click Details, then select Internet Gateway Device Discovery and Control Client and UPnP User Interface.

4. Click OK to begin the installation.

To enable UPnP in Windows 7:

1. Go to Start > Control Panel > Network and Internet > Network and Sharing Center.

2. On the left pane, click Change advanced sharing settings.

3. On your current network profile, in the Network discovery area, click Turn on network discovery, and then click Save changes.

Page 47

Configuring SNMP Settings

You can configure Simple Network Management Protocol (SNMP) settings on the Setup > Network Setup > SNMP page.

SNMP is a protocol for collecting, organizing, and exchanging management information between managed devices on a network.

To enable SNMPv1 and/or SNMPv2:

Configuring Network Settings

1. Next to SNMP Version, select the SNMP version(s) that you want to use. You can select SNMPv1 only, SNMPv2 only, both SNMPv1 and SNMPv2, or SNMPv3 only.

2. By default, the SNMP Port is 161. To change the port, enter a number in the range 1–65535.

3. In the Trap Address field, enter the IP address of the SNMP server where trap notifications will be sent.

4. By default, the Trap Port is 162. To change the port, enter a number in the range 1–65535.

5. Click Save to apply the settings.

Configuring Bonjour

You can configure Bonjour settings on the Setup > Network Setup > Bonjour page.

Bonjour is a zero configuration networking application that allows you to create a network in which devices can discover each other without requiring any user configuration.

When this function is enabled, you can discover the camera on a Mac OS computer by opening Safari and going to Display All Bookmarks > Bonjour.

Bonjour is enabled by default. To disable it, clear the Enable check box, and then click Save.

Page 48

Ultra HD IP Camera User Guide

Configuring Multicast Settings

You can configure multicast settings on the Setup > Network Setup > Multicast page.

Multicast is a transmission mode for data packets that minimizes bandwidth use and CPU load whe n multiple computers are receiving the same data packet simultaneously. You can configure multicast for Main Stream, Sub Stream 1, and Sub Stream 2 profiles.

To enable multicast:

1. For each stream that you want to enable multicast in, select the Enable check box, and then enter a multicast address and port, using the suggested ranges as a guide.

2. Click Save to apply the settings.

To view video in multicast mode:

• In Live view, select Multicast from the Protocol drop-down list.

Configuring 802.1X Settings

You can configure 802.1X settings on the Setup > Network Setup > 802.1X page.

802.1X is a port-based network access control protocol for preventing unauthorized devices

from accessing the LAN. You can set up user name and password credentials for the camera so that it is not blocked by the network switch.

To enable 802.1X:

1. Select the Enable check box.

2. In the User Name field, enter the user name that will be used to authenticate the camera.

3. In the Password field, enter the password that will be used to authenticate the camera.

4. Click Save to apply the settings.

Page 49

Configuring QoS Settings

You can configure Quality of Service (QoS) settings on the Setup > Network Setup > QoS page.

QoS settings control bandwidth use by prioritizing certain data packets over others.

To enable QoS:

1. In the Realtime Monitor field, enter a DSCP (Differentiated Services Codepoint) value for live video packets. Select a value between 0 (lowest priority) and 63 (highest priority).

2. In the Command field, enter a DSCP (Differentiated Services Codepoint) value for non-video packets. Select a value between 0 (lowest priority) and 63 (highest priority).

3. Click Save to apply the settings.

Configuring Network Settings

Working with Certificates

You can configure certificate settings on the Setup > Network Setup > Certificate page.

To install a Honeywell-signed root certificate:

1. Click Export, navigate to the directory where you want to save the certificate (ca.crt) on your PC, and then click Save.

2. Go to the directory where you saved the certificate and double-click the certificate. The Certificate window opens.

3. In the Certificate window, on the General tab, click Install Certificate to open the Certificate Import Wizard.

4. Click Next to continue.

5. Click Place all certificates in the following store, click Browse, click Trusted Root Certification Authorities, and then click OK.

6. Click Next, and then click Finish to close the Certificate Import Wizard. A confirmation dialog box appears with the message “The import was successful.”

7. Click OK, and then click OK to close the Certificate window.

Page 50

Ultra HD IP Camera User Guide

To import a certificate or private key:

• Next to CA or Key, click Browse, navigate to the location of the certificate or key on your

PC, and then click Import.

Page 51

Configuring Event Settings

6. Configuring Event Settings

This chapter contains the following sections:

• Configuring Alarm Events, page 41

• Configuring System Events, page 43

• Configuring Motion Detection Events, page 45

• Configuring Camera Tampering Events, page 47

• Configuring Scene Change Events, page 48

• Configuring Audio Events, page 49

• Configuring Face Detection Events, page 52

• Configuring People Counting Events, page 53

Configuring Alarm Events

You can configure alarm event settings on the Setup > Alarm Setup > Alarm Setup page.

To enable the alarm function:

1. Select the Enable check box.

2. From the Alarm Input list, select the alarm input that you want to configure (Alarm1 or Alarm2).

Page 52

Ultra HD IP Camera User Guide

3. Next to Alarm Period, click Setup. The Alarm Period window opens.

4. Set the days and times when you want the alarm function to be active, and then click Save.

5. In the Anti-Dither field, enter the anti-dither time in seconds. Enter a value between 0 and 100 seconds. The system will only allow one alarm event within this period.

6. Set Sensor Type to NO (normally open) or NC (normally closed), depending on the alarm input type.

7. To start recording video when an alarm event is detected, select the Record check box.

8. In the Record Delay field, enter the number of seconds that the system will continue to record video after an alarm event has ended. Enter a value between 10 and 300.

9. To generate an alarm output when an alarm event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

10. In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after an alarm event has ended. Enter a value between 10 and

300.

11. To send an email notification when an alarm event is detected, select the Send Email check box. Email settings must be configured in Setup > Network Setup > SMTP (Email). See Configuring Email Settings on page 35.

12. To take a snapshot when an alarm event is detected, select the Snapshot check box.

Note For the snapshot to be attached to the email notification, the Attachment

check box must be selected in Setup > Network Setup > SMTP (Email).

13. Click Save to apply the settings.

See Configuring Email Settings on page 35.

Page 53

Configuring System Events

You can configure system event settings (for SD card and network errors and illegal login attempts) on the Setup > Alarm Setup > Event page.

Configuring SD Card Event Settings

There are three types of SD card events:

• No SD Card: There is no microSD card installed in the camera.

• SD Card Error: The installed microSD card is not working.

• Capacity Warning: The installed microSD card is full.

You can configure settings for each type of event.

Configuring Event Settings

To enable SD card event detection:

1. On the SD Card tab, select the event type that you want to configure from the Event Type list (No SD Card, SD Card Error, or Capacity Warning).

2. Select the Enable check box.

3. To generate an alarm output when an event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

4. In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after the event has ended. Enter a value between 10 and 300.

5. To send an email notification when the event is detected, select the Send Email check box. Email settings must be configured in Setup > Network Setup > SMTP (Email). See

Configuring Email Settings on page 35.

6. Click Save to apply the settings.

Configuring Network Event Settings

There are two types of network events:

• Network Disconnected: The camera is offline.

• IP Conflict: The camera has the same IP address as another device on the network.

Page 54

Ultra HD IP Camera User Guide

You can configure settings for each type of event.

To enable network event detection:

1. On the Network tab, select the event type that you want to configure from the Event Type list (Network Disconnected or IP Conflict).

2. Select the Enable check box.

3. In the IP Address field, enter the IP address of the headend, and in the Time field, enter the countdown time. If no connection is established with the IP address within the specified time, the system will will detect a network disconnection event.

4. To start recording video whe n the event is detected, select the Record check box.

5. In the Record Delay field, enter the number of seconds that the system will continue to record video after the event has ended. Enter a value between 10 and 300.

6. To generate an alarm output when an event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

7. In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after the event has ended. Enter a value between 10 and 300.

8. Click Save to apply the settings.

Configuring Illegal Access Event Settings

An illegal access event occurs when a specified number of unsuccessful login attempts is exceeded.

Page 55

To enable illegal access detection:

1. On the Illegal Access tab, select the Enable check box.

2. In the Failed Login Attempts field, enter the number of unsuccessful login attempts the system will allow before an illegal access event is detected. Enter a value between 3 and 10.

3. To generate an alarm output when an event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

4. In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after the event has ended. Enter a value between 10 and 300.

5. To send an email notification when an illegal access event is detected, select the Send

Email check box. Email settings must be configured in Setup > Network Setup > SMTP (Email), See Configuring Email Settings on page 35.

Configuring Motion Detection Events

You can configure motion detection event settings on the Setup > Video Analytics > Video Detection > Motion Detection page.

Configuring Event Settings

To enable motion detection:

1. Select the Enable check box.

2. Next to Alarm Period, click Setup. The Alarm Period window opens.

3. Set the days and times when you want the alarm function to be active, and then click Save.

4. In the Anti-Dither field, enter the anti-dither time in seconds. Enter a value between 0 and 100 seconds. The system will only allow one motion detection event within the Anti-Dither period.

5. Set up motion detection areas:

Page 56

Ultra HD IP Camera User Guide

a. Next to Area, click Setup. The Area window opens.

b. By default, the whole video window is configured as a motion detection area. To

c. You can define up to 4 motion detection profiles (regions), each with different

define a smaller area, drag your mouse over the area(s) that you want to deselect, or click Remove All, and then redraw the area(s) with your mouse.

sensitivity and threshold settings. Next to Region, click one of the solid color tiles to select a region. Drag the Sensitivity and Threshold sliders to the desired values. Click the – and + signs to make fine adjustments.

Sensitivity measures the amount of change in a scene that qualifies as motion. Threshold measures the amount of motion in a scene required to trigger a motion detection event.

d. Click Save to apply the settings.

6. To start recording video when motion is detected, ensure that the Record check box is selected.

7. In the Record Delay field, enter the number of seconds that the system will continue to record video after the event has ended. Enter a value between 10 and 300.

8. To generate an alarm output when motion is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

Page 57

9. In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after the event has ended. Enter a value between 10 and 300.

10. To send an email notification when motion is detected, select the Send Email check box. Email settings must be configured in Setup > Network Setup > SMTP (Email). See

Configuring Email Settings on page 35.

11. To take a snapshot when motion is detected, select the Snapshot check box.

Note For the snapshot to be attached to the email notification, the Attachment

check box must be selected in Setup > Network Setup > SMTP (Email). See Configuring Email Settings on page 35.

12. Click Save to apply the settings.

Configuring Camera Tampering Events

You can configure camera tampering event settings on the Setup > Video Analytics > Video Detection > Video Tampering page.

Configuring Event Settings

To enable camera tampering detection:

1. Select the Enable Tamper Detect and/or the Enable Defocus Detect check box(es).

2. Next to Alarm Period, click Setup. The Alarm Period window opens.

3. Set the days and times when you want the alarm function to be active, and then click Save.

4. To start recording video when a tampering event is detected, ensure that the Record check box is selected.

5. In the Record Delay field, enter the number of seconds that the system will continue to record video after a tampering event has ended. Enter a value between 10 and 300.

6. To generate an alarm output when a tampering event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

7. In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after a tampering event has ended. Enter a value between 10 and 300.

Page 58

Ultra HD IP Camera User Guide

8. To send an email notification when a tampering event is detected, select the Send

Email check box. Email settings must be configured in Setup > Network Setup > SMTP (Email). See Configuring Email Settings on page 35.

9. To take a snapshot when a tampering event is detected, select the Snapshot check box.

Note For the snapshot to be attached to the email notification, the Attachment

check box must be selected in Setup > Network Setup > SMTP (Email). See Configuring Email Settings on page 35.

10. Click Save to apply the settings.

Configuring Scene Change Events

You can configure scene change event settings on the Setup > Video Analytics > Video Detection > Scene Change page.

To enable scene change detection:

1. Select the Enable check box.

2. Next to Alarm Period, click Setup. The Alarm Period window opens.

3. Set the days and times when you want the alarm function to be active, and then click Save.

4. To start recording video when a scene change event is detected, select the Record check box.

5. In the Record Delay field, enter the number of seconds that the system will continue to record video after a scene change event has ended. Enter a value between 10 and 300.

6. To generate an alarm output when a scene change event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

7. In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after a scene change event has ended. Enter a value between 10 and 300.

Page 59

8. To send an email notification when an alarm event is detected, select the Send Email check box. Email settings must be configured in Setup > Network Setup > SMTP (Email). See Configuring Email Settings on page 35.

9. To take a snapshot when an alarm event is detected, ensure that the Snapshot check box is selected.

Note For the snapshot to be attached to the email notification, the Attachment

check box must be selected in Setup > Network Setup > SMTP (Email). See Configuring Email Settings on page 35.

10. Click Save to apply the settings.

Configuring Audio Events

You can configure audio event settings on the Setup > Video Analytics > Audio Detection page.

Configuring Event Settings

To enable audio event detection:

1. To detect faults in the audio input, select the Enable Input Abnormality check box.

2. To detect unusual changes in the audio input:

a. Select the Enable Intensity Change check box.

Page 60

Ultra HD IP Camera User Guide

b. Drag the Sensitivity and Threshold sliders to the desired values. Click the – and +

3. Next to Alarm Period, click Setup. The Alarm Period window opens.

4. Set the days and times when you want the alarm function to be active, and then click Save.

5. In the Anti-Dither field, enter the anti-dither time in seconds. Enter a value between 0 and 100 seconds. The system will only allow one audio event within the Anti-Dither period.

6. To start recording video when an audio event is detected, ensure that the Record check box is selected.

7. In the Record Delay field, enter the number of seconds that the system will continue to record video after an audio event has ended. Enter a value between 10 and 300.

8. To generate an alarm output when an audio event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

9. In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after an audio event has ended. Enter a value between 10 and

300.

10. To send an email notification when an audio event is detected, select the Send Email check box. Email settings must be configured in Setup > Network Setup > SMTP (Email). See

11. To take a snapshot when an audio event is detected, select the Snapshot check box.

signs to make fine adjustments. Sensitivity controls changes to the audio input volume. Threshold controls the amount of change allowed in the audio environment before an audio detection event is triggered.

Configuring Email Settings on page 35.

Note For the snapshot to be attached to the email notification, the Attachment

check box must be selected in Setup > Network Setup > SMTP (Email). See Configuring Email Settings on page 35.

12. Click Save to apply the settings.

Accessing Extensional Smart Function

IntrusionTrace, LoiteringTrace and License Plate Recognition are video analytics applications designed for 24/7 outdoor operation. You can access Extensional Smart Functions from the Setup > Video Analytics > Smart Plan page.

To access Extensional Smart Function:

1. Set Extensional smart function to ON.

2. Click the Extensional smart function tab.

Page 61

Configuring Event Settings

Note

3. Select the target function, click Save and then click Open correspondingly.

Only for H4L6GR2 and HBL6GR2

Page 62

Ultra HD IP Camera User Guide

Configuring Face Detection Events

You can configure face detection event settings on the Setup > Video Analytics > Face Detection page.

To enable face detection:

1. Select the Enable check box.

2. Click Draw Target to set up the face detection area. You can move or resize the area using your mouse. To move the area, drag one of the sides. To resize the area, drag one of the corner handles.

3. Next to Alarm Period, click Setup. The Alarm Period window opens.

4. Set the days and times when you want the alarm function to be active, and then click Save.

5. To enable face enhancement, select the Enable Face Enhancement check box.

6. To start recording video when an event is detected, select the Record check box.

7. In the Record Delay field, enter the number of seconds that the system will continue to record video after the event has ended. Enter a value between 10 and 300.

8. To generate an alarm output when an event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

9. In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after the event has ended. Enter a value between 10 and 300.

10. To send an email notification when an event is detected, select the Send Email check box. Email settings must be configured in Setup > Network Setup > SMTP (Email). See

Configuring Email Settings on page 35.

11. To take a snapshot when an event is detected, select the Snapshot check box.

Note For the snapshot to be attached to the email notification, the Attachment check box

must be selected in Setup > Network Setup > SMTP (Email). See Configuring Email Settings on page 35.

Page 63

12. Click Save to apply the settings.

Configuring People Counting Events

Note Only for H4L6GR2 and HBL6GR2.

People Counting

You can track the movement of people entering or leaving an area using the people counter function.

Configuring Event Settings

1. Select the Enable check box to enable the people counting function.

2. Click Draw Rule and then drag your mouse over the area of the video image that you want to monitor.

3. Click Draw Target, and then, next to Target Filter, select Max Size. Use your mouse to draw the maximum target size. Next, select Min Size, and use your mouse to draw the minimum target size.

4. Click Setup to to set the days and times when you want the people counting function to be active.

5. Enter a name for the rule.

6. Select the flow direction: A->B or B->A.

7. Enter the desired values for Enter Number, Leave Number, and Stranded Number. When any of the numbers is exceeded, an alarm is generated.

8. Select the check box to start recording video when an alarm is generated.

9. Enter the time that the system will continue recording video after an alarm is generated (10–300 seconds).

10. Select the Alarm Output check box to activate an alarm output when an alarm is generated.

11. Enter the time that the system will continue to generate an alarm output after an alarm

Page 64

Ultra HD IP Camera User Guide

is generated (10–300 seconds).

12. Select the check box to send an email notification when an alarm is generated. Email settings must be configured in Setup > Network Setup > SMTP (Email).

13. Select the check box to save a snapshot when an alarm is generated. The snapshot is saved to the location(s) specified in

Report

You can generate a report that displays people counting data for a specified range of time.

1. Report Type: Select the desired report type: Day, Month, or Year. To display the report as a bar chart or as a line chart, click the corresponding radio button.

2. Start Time: Enter the start date and time of the report.

3. End Time: Enter the end date and time of the report.

Setup > Storage Setup > Destination > Path.

4. Select the Flow Direction check boxes of the information that you want to include in the report. For example, to display the number of people entering, click the Enters check box and the Display Numbers check box.

5. Search: To view the report, click Search.

6. Export: To export and save the report to a local drive, click Export.

Page 65

7. Configuring Recording Settings

This chapter contains the following sections:

• Configuring Recording Schedules, page 55

• Configuring Storage Settings, page 56

• Configuring Recording Settings, page 59

Configuring Recording Schedules

You can set up both regular and holiday schedules for recording video and saving snapshots on the Setup > Storage Setup > Schedule page.

Configuring Recording Settings

Page 66

Ultra HD IP Camera User Guide

On the Record Schedule tab, click the Setup buttons to configure weekend, weekday, and holiday settings, for general video recording as well as motion detection and alarm recording.

You can configure up to 6 different recording periods per day. Click Save to apply the settings.

Follow the same procedure to configure the settings on the Snapshot Schedule tab.

On the Holiday Schedule tab, you can designate holidays by clicking dates on the calendar.

On the selected dates, the video recording/snapshot schedule will follow the holiday settings you configured in the Record Schedule and Snapshot Schedule tabs. Click Save to apply the settings.

Configuring Storage Settings

You can configure recording storage settings on the Setup > Storage Setup > Destination page.

Page 67

Configuring Recording Settings

Configuring Storage Paths

On the Path tab, you can specify where you want recorded video and snapshots—whether scheduled or triggered by a motion detection or alarm event—to be saved: to a local SD card, to an FTP server, or to an NAS disk.

Select which recorded events you want to save and where you want to save them, then click

Save to apply the settings.

Note Only one network storage option can be used at a time. FTP and NAS cannot

be used together.

Configuring the Local SD Card for Storage

If the camera has a microSD card installed, the Local tab displays the microSD card details.

You can set up the installed microSD card for read-only, read-and-write, or hot swap operation by clicking the corresponding button.

• Read Only: Data on card can be displayed but not modified.

• Read & Write: Data on card can be displayed and modified.

• Hot Swap: Card can be inserted or removed without turning off the camera.

If you want to erase all of the data on the microSD card, click Format. A confirmation message appears. Click OK to continue. The card is formatted and the camera reboots.

Page 68

Ultra HD IP Camera User Guide

Configuring an FTP Server for Storage

On the FTP tab, you can enable FTP storage and configure storage settings.

To enable FTP storage:

1. Select the Enable check box.

2. In the Server Address and Port fields, enter the address and port number of the FTP server.

3. In the User Name and Password fields, enter the user name and password of the server.

4. In the Remote Directory field, enter the directory on the server where the recorded video/snapshot files will be stored.

5. Click Save to apply the settings.

Panic Save

To save recorded video/snapshots to the camera's microSD card when the network connection to the FTP is offline or unavailable, select the Panic Save (Local) check box, and then click Save to apply the setting.

Configuring an NAS Disk for Storage

On the NAS tab, you can enable network attached storage and configure storage settings.

To enable network attached (NAS) storage:

1. Select the Enable check box.

2. In the Server Address field, enter the address of the NAS server.

3. In the Remote Directory field, enter the directory on the server where the recorded video/snapshot files will be stored.

4. Click Save to apply the settings.

Page 69

Configuring Recording Settings

You can configure recording settings on the Setup > Storage Setup > Record Control page.

By default, recorded video files are 8 minutes or 30 minutes long (depending on your camera model). To change this setting, enter a time between 1 and 120 minutes in the Record Length field.

By default, the pre-event record time (the number of seconds the system stores in a buffer) is 5 seconds. To change this setting, enter a time between 0 and 5 seconds in the Pre-Event Record field.

Configuring Recording Settings

From the Disk Full list, select Overwrite or Stop.

• Overwrite: Recording continues when disk capacity is reached and overwrites

previously saved video.

• Stop: Recording stops when disk capacity is reached. Nothing is overwritten and no

further video is recorded.

Set Record Mode to Auto, Manual, or Off.

• Auto: Video records continuously.

• Manual: Video recording must be initiated by user.

• Off: Video recording is disabled.

From the Record Stream list, select the stream profile that you want to use for recording video: Main Stream or Sub Stream.

Click Save to apply the settings.

Page 70

Ultra HD IP Camera User Guide

8. Configuring System Settings

This chapter contains the following sections:

• Configuring General System Settings, page 60

• Configuring Date and Time Settings, page 61

• Configuring Account Settings, page 63

• Resetting the Camera, page 68

• Backing Up/Restoring a Configuration, page 68

• Configuring Maintenance Settings, page 69

• Upgrading the Firmware, page 69

• Viewing Version Information, page 69

• Managing Logs, page 70

• Viewing Online Users, page 72

Configuring General System Settings

You can configure the device name, user interface language, video standard, analog output, and status LED settings on the Setup > System Setup > General page.

To change the device name, in the Device Name field, enter a new name, and then click Save.

To change the interface language, select a language from the

To change the video standard, select NTSC or PAL from the Video Standard list, and then click Save.

To change the analog output, select ON or OFF from the Analog Output list, and then click Save.

To change the Max Log Quantity, enter a value between 1 and 1024, and then click Save.

Language

list, and then click

Save

Page 71

The status LED is enabled by default. To disable it, set Save.

Configuring Date and Time Settings

You can configure the date and time settings on the Setup > System Setup > Date & Time page.

Status LED

Configuring System Settings

Control to OFF, and then click

Changing the Date and Time Format

You can change the format of the date and time that appear in the text overlay on the video.

To change the date format, select one of the following formats from the Date Format list: Year-Month-Day, Month-Day-Year, or Day-Month-Year. Click Save to apply the settings.

To change the time format, select 24_Hour_Standard or 12_Hour_Standard from the Time Format list.

Setting the Date and Time

There are three ways you can set the camera’s date and time. You can manually enter the date and time, synchronize with your PC’s internal clock, or set up the camera to synchronize automatically with a Network Time Protocol (NTP) server at regular intervals.

To manually set the date and time, enter the date and time in the Current Time fields, and then click Save.

To synchronize the date and time with your PC, click Sync PC. If the synchronization is successful, the message “Save succeeded” appears. You must manually click Sync PC each time you want the date and time to synchronize with the PC.

To synchronize the time with an NTP server:

1. From the Time Zone list, select your time zone.

2. If you are in an area that observes Daylight Saving Time (DST):

Page 72

Ultra HD IP Camera User Guide

a. Select the Enable DST check box.

b. Set DST Type to Week.

c. Set Start Time to Mar 2nd Sunday 02:00:00 AM.

d. Set End Time to Nov 1st Sunday 02:00:00 AM.

3. Select the Synchronize with NTP check box.

4. If you want, you can change the NTP Server from the default (time-a.nist.gov).

5. In Update Period field, enter the interval at which you want the camera’s date and time to synchronize with the NTP server. You can enter a value between 0 and 30.

6. Click Save to apply the settings.

Configure Multi Sensor

Note Only for HM4L8GR1 and HMBL8GR1.

You can configure the Multi Video Sensor to optimize the image stitching on the Setup > System Setup > Multi Video Sensor page

To configure the Multi Video Sensor:

1. When the camera installation is completed, let the lens focus on an open field.

2. Click Start.

Page 73

Configuring Account Settings

You can manage user accounts and permissions on the Setup > System Setup > Account page.

Managing Groups

Configuring System Settings

By default, there are two categories or “groups” of users: admin and user. If needed, you can create additional customized groups.

Page 74

Ultra HD IP Camera User Guide

Creating a Group

You can create a new custom group and assign permissions to it.

To create a group:

2. Enter a name for the group in the Group field.

3. If you want, you can enter a brief description in the Remark field.

4. From the Authority List, select permissions for the group (see Table 8-1).

1. On the Group tab, click Add Group to open the Add Group window.

Table 8-1 Permissions

Name Description

Live The user can view live video and access all of the controls in the Live interface.

Playback The user can play back recorded video and access all of the controls in the

Playback

Record Control The user can access the settings in Setup > Storage Setup > Record Control.

Backup The user can save and export video clips in the Playback interface.

User Management The user can access the settings in Setup > System Setup > Account.

Alarm The user can access the settings in Setup > Alarm Setup > Alarm.

Log Search The user can search logs in Setup > Information > Log.

Clear Log The user can clear logs in Setup > Information > Log.

Upgrade The user can upgrade firmware in Setup > System Setup > Upgrade.

Auto Maintain The user can access the settings in Setup > System Setup > Auto Maintain.

General The user can access the settings in Setup > System Setup > General.

Video/Audio The user can access the settings in Setup > Compression Setup > Video and in

Setup > Audio Setup.

Schedule/Destination The user can access the settings in Setup > Storage Setup > Schedule and in

Setup > Storage Setup > Destination.

Network The user can access the settings in Setup > Network Setup.

Event The user can access the settings in Setup > Alarm Setup > Event.

Video Detection The user can access the settings in Setup > Video Analytics > Video Detect.

Restore Defaults The user can access the settings in Setup > System S etup > Default.

Camera Properties The user can access the settings in Setup > Camera Setup > Properties.

IVS The user can access the settings in Setup > Video Analytics.

interface.

5. Click Save to apply the settings. The group is added to the list.

Page 75

Configuring System Settings

Modifying a Group

You can modify the permissions of the administrator group, user group, and any custom groups that you have created.

To modify a group:

1. On the Group tab, select the group that you want to modify (your selection will be highlighted yellow), and then click the Modify icon to open the Modify Group window.

2. If you want, you can edit the description in the Remark field.

3. From the Authority List, select or deselect specific permissions for the group (see

Table 8-1), or select the All check box to select/deselect all of the permissions.

4. Click Save to apply the settings.

Deleting a Group

You can delete any custom group that you have created (you cannot delete the administrator group or the user group).

To delete a group:

1. On the Group tab, select the group that you want to delete (your selection will be highlighted yellow), and then click the Delete icon .

2. A confirmation message appears. Click OK to continue. The group is removed from the list.

Page 76

Ultra HD IP Camera User Guide

Managing Users

You can create, modify, or delete a user account.

Creating a User Account

You can create a new user account and assign permissions to it.

To create a user account:

1. On the User Name tab, click Add User to open the Add User window.

2. Assign the account a user name and password.

a. In the User Name field, enter a unique user name.

b. In the Password field, enter a password. The password must be at least 8

characters in length and contain a combination of uppercase and lowercase letters, at least one number, and at least one special character.

3. Assign the account to a group (admin, user, or a custom group that you have created) chosen from the Group list.

4. If you want, you can enter a brief description in the Remark field.

5. From the Authority List, select permissions for the account (see Table 8-1).

Note Each user is assigned to a group. The individual user’s permissions cannot

exceed those of the group to which the user belongs. To modify permissions at the group level, see Modifying a Group on page 65.

6. Click Save to apply the settings. The user account is added to the list.

Page 77

Configuring System Settings

Modifying a User Account

You can modify the user name, password, and permissions of a user account.

To modify a user account:

1. On the User Name tab, select the user account that you want to modify (your selection will be highlighted yellow), and then click the Modify icon to open the Modify User window.

2. To change the password, select the Modify Password check box, enter the Old Password and the New Password in the corresponding fields, and then re-enter the new password in the Confirm Password field.

3. To change the group, select a group from the Group list.

4. If you want, you can edit the description in the Remark field.

5. From the Authority List, select or deselect specific permissions for the account (see

Table 8-1), or select All to select/deselect all of the available permissions.

Note Each user is assigned to a group. The individual user’s permissions cannot

exceed those of the group to which the user belongs. To modify permissions at the group level, see Modifying a Group on page 65.

6. Click Save to apply the settings.

Deleting a User Account

You can delete any user account that you have created (you cannot delete the admin user).

To delete a user account:

1. On the User Name tab, select the user account that you want to delete (your selection will be highlighted yellow), and then click the Delete icon .

2. A confirmation message appears. Click OK to continue. The user account is removed from the list.

Page 78

Ultra HD IP Camera User Guide

Resetting the Camera

You can reset the camera to its factory default settings on the Setup > System Setup > Default page.

Note Some configuration information, including the IP address, will be lost when the

To reset the camera:

1. Click Default.

2. A confirmation message appears. Click OK to continue. The camera reboots automatically and reverts to its factory default settings.

camera reverts to its factory default settings.

Backing Up/Restoring a Configuration

You can back up or restore configuration settings on the Setup > System Setup > Import/Export page.

To back up a configuration:

1. Click Export. The Save As window opens.

2. By default, the backup file is named DeviceConfig.backup. Rename the file if you want, navigate to the directory where you want to save the file, and then click Save. The file path is displayed under Backup Path.

To restore a saved configuration:

1. Click Import. The directory displayed under Backup Path opens in a new window.

2. Click the backup file (for example, DeviceConfig.backup). The configuration settings are applied immediately.

Page 79

Configuring Maintenance Settings

Two automatic maintenance functions are available on the Setup > System Setup > Auto Maintain page. You can set up the camera to reboot daily or weekly and delete old files

automatically.

To enable the auto reboot function, select the Auto Reboot check box, and then specify the reboot schedule (for example, every Tuesday at 2 a.m.). Click Save to apply the settings.

To enable the auto delete function, select the Auto Delete Old Files check box, and then specify the age (in days) of the files to be deleted. For example, if you enter 30, files that are 30 days old and older will be deleted automatically. Click Save to apply the settings.

Configuring System Settings

Upgrading the Firmware

You can upgrade the camera firmware on the Setup > System Setup > Upgrade page.

Note Before you begin, you will need to obtain the new firmware and save it to your

To upgrade the firmware:

1. Click Import.

2. Navigate to the location of the firmware file (.bin), select it, and then click Open. The file name appears in the Firmware File field.

3. Click Upgrade to install the firmware.

4. Reboot the camera.

PC or to an external drive.

Viewing Version Information

You can view the camera’s firmware version, web client version, ONVIF version, and serial number on the Setup > Information > Version page.

Page 80

Ultra HD IP Camera User Guide

Managing Logs

You can view, back up, and delete log files on the Setup > Information > Log page.

Viewing Logs

There are seven log types: System, Setting, Data, Event, Record, Account, and Clear Log.

To view logs by type:

1. Enter the Start Time and End Time search parameters.

2. From the All Types list, select the log type(s) that you want to retrieve, and then click Search. The logs are listed by time, user name, and event (if applicable).

Page 81

Configuring System Settings

3. To view detailed information about a specific log, click the log. The information is displayed in the System Log Information box.

Backing Up Logs

Deleting Logs

To back up a log:

1. Click Backup. The Save As window opens.

2. By default, the backup file is named LogBackup[YYYY-MM-DD].txt. Rename the file if you want, locate the directory whe re you want to save the file, and then click Save.

To delete all logs:

1. Click Clear.

2. A confirmation message appears. Click OK to continue. All of the logs that you have not backed up are deleted.

Page 82

Ultra HD IP Camera User Guide

Viewing Online Users

You can see which users are currently online on the Setup > Information > Online User page. The users are listed by user name, IP address, and login time. To refresh the list, click Refresh.

Page 83

Technical Specifications

Auto/Natural/Street Lamp/Outdoor/Manual/Customized Region

Electronic Image Stabilization

80×960)/720P(1280×720)(1~25/30fps)

TCP/IP, UDP, ICMP, IPv4, IPv6, SNMP v2c/v3, QoS, HTTP,

cast

9. Technical Specifications

H4L6GR2 Mini Dome Camera

Table A-1 H4L6GR2 Specifications

Camera

Video Standard NTSC/PAL

Image Sensor

Number of Pixels (H×V) 3072 x 2048

Minimum Illumination Color : 0.004Lux @F/1.53, B/W : 0Lux @F/1.53(IR on)

Lens 4.1~16.4 mm, MFZ, F1.53 (Max)

Horizontal Angle of View 107°–35°

S/N Ratio 50 dB or more

Electronic Shutter Speed Auto, Manual, 1/30–1/100 000 s

IR Distance Up to 164 ft (50 m)

Day/Night Auto(ICR)/Color/BW

Backlight Compensation BLC/HLC/DWDR/SSA

White Balance

Gain Control Auto/Manual

Noise Reduction 3DNR

Privacy Masking Up to 4 configurable areas

Defog Auto/Manual/Off

Audio Input/Output 1/1

Alarm Input/Output 2/1

Onboard Storage Up to 128 GB microSDHC card, Class 10 (not included)

Network

Video Compression H.265/H.264+/H.264/MJPEG

Resolution

Frame Rate

Audio Compression G.711a/G.711mu/AAC/G.726

Audio Stream Dual-Channel

Ethernet RJ-45 (100/1000Base-T)

1/1.8ʺ 6 MP progressive scan CMOS

Off/On

6M(3072×2048)/5M(2560×1920)/3M(2048×1536)/ 3M(2304x1296)/1080P(1920×1080)/1.3M(1280×960)/ 720P(1280×720)/D1(704×480)/VGA(640×480)/CIF(352 ×288/352×240)

Main Stream:6M(3072×2048)/5M(2560×1920)/3M(204 8×1536)/3M(2304x1296)/1080P(1920×1080)/1.3M(12

Sub Stream: D1/CIF/VGA(1 ~ 25/30fps)

Triple Stream: 1080P/720p/D1(1 ~ 25/30fps)

Protocols

DHCP, HTTPS, SSL, SMTP, FTP, RTSP, UPnP, DNS, DDNS, NTP, RTP, RTCP,PPPOE,Bonjour,802.1x, Multi-

Page 84

Ultra HD IP Camera User Guide

Multiple user access levels with enhanced password

RAL9003 (White) and RAL7022 (Gray)

Emissions: EN 55032 ， ANSI C63.4-2014,ICE 003

Safety: EN 60950-1, EN 60950-22, UL Listed to UL/CSA 60950-1, UL/CSA 60950-22

and greater)

Entry to Enterprise Level Network Video VMS (R450 and greater)

Compatibility ONVIF Profile S/G/Q

Max. Users 10 (Unicast)/20 (Multicast)

Supported Web Browsers Internet Explorer (11.0+), Firefox, Chrome

Supported OS Windows 7, 32-bit/64-bit

Security

policy ,IP filtering, IEEE 802.1x, Strong Digest authentication for Access permission, Force to HTTPS with secure protocol TLS1.2 only and highly strength encrypted algorithm AES-256, SSH/Telnet closed & FTP disabled for reducing the surface being attacked, Comply with PCI-DSS ,Cyber-security hardware chipset for private key.

Languages

General

Input Voltage PoE+ (802.3at) Class 4, 12 VDC/24 VAC (±25%)

Power Consumption 18 W max. (with IR LEDs on and motorized lens working)

Dimensions 6.3 × 4.6 in. (159 × 118mm)

Weight 2.7 lb (1.2 kg)

Construction Die-cast aluminum housing with powder coat

Color

Temperature –40°F to 140°F (–40°C to 60°C)

Relative Humidity Less than 95%, non-condensing

Ingress Protection IP67

Impact Resistance IK10

Regulatory

Integration

MAXPRO NVR Family

English, Arabic, Czech, Dutch, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Simplified Chinese, Spanish, Turkish

Rev6， AS/NZ CISPR 32:2013

Immunity: EN 50130-4

RoHS: EN 50581

Entry to Enterprise Level Network Video Recorders (4.5

MAXPRO VMS Family

DVM DVM R620

HUS HUS 5.1 SP

Accessories

HB4G-PM Pole Mount Adapter HB34G-CM Corner Mount Adapter H4G-PK Pendant Mount Bracket HD4CHIP-PK2 Penda nt Mount Bracket HD4CHIP-WK2 Wall Mount Bracket H4G-CB Replacement Dome (Clear) H4G-SB Replacement Dome (Smoke )

Page 85

Technical Specifications

Auto/Natural/Street Lamp/Outdoor/Manual/Customized Region

TCP/IP, UDP, ICMP, IPv4, IPv6, SNMP v2c/v3, QoS, HTTP,

cast

HBL6GR2 Bullet Camera

Table A-2 HBL6GR2 Specifications

Camera

Video Standard NTSC/PAL

Image Sensor

Number of Pixels (H×V) 3072 x 2048

Minimum Illumination Color : 0.004Lux @F/1.53, B/W : 0Lux @F/1.53(IR on)

Lens 4.1~16.4 mm, MFZ, F1.53 (Max)

Horizontal Angle of View 86°–35°

S/N Ratio 50 dB or more

Electronic Shutter Speed Auto, Manual, 1/30–1/100 000 s

IR Distance Up to 164 ft (50 m)

Day/Night Auto(ICR)/Color/BW

Backlight Compensation BLC/H LC/DWDR/SSA

White Balance

Gain Control Auto/Manual

Noise Reduction 3DNR

Privacy Masking Up to 4 configurable areas

Electronic Image Stabilization Off/On

Defog Auto/Manual/Off

Audio Input/Output 1/1

Alarm Input/Output 2/1

Onboard Storage Up to 128 GB microSDHC card, Class 10 (not included)

Network

Video Compression H.265/H.264+/H.264/MJPEG

Resolution

Frame Rate

Audio Compression G.711a/G.711mu/AAC/G.726

Audio Stream Dual-Channel

Ethernet RJ-45 (100/1000Base-T)

1/1.8ʺ 6 MP progressive scan CMOS

6M(3072×2048)/5M(2560×1920)/3M(2048×1536)/ 3M(2304x1296).1080P(1920×1080)/1.3M(1280×960)/ 720P(1280×720)/D1(704×480)/VGA(640×480)/CIF(352 ×288/352×240)

Main Stream: 6M(3072×2048)/5M(2560×1920)/3M(204 8×1536)/3M(2304x1296) 1080P(1920×1080)/1.3M(12 80×960)/720P(1280×720)(1~25/30fps)

Sub Stream: D1/CIF/VGA(1 ~ 25/30fps)

Triple Stream: 1080P/720p/D1(1 ~ 25/30fps)

Protocols

Compatibility ONVIF Profile S/G/Q

Max. Users 10 (Unicast)/20 (Multicast)

DHCP, HTTPS, SSL, SMTP, FTP, RTSP, UPnP, DNS, DDNS, NTP, RTP, RTCP,PPPOE,Bonjour,802.1x, Multi-

Page 86

Ultra HD IP Camera User Guide

Multiple user access levels with enhanced password

with PCI-DSS, cyber…

Simplified Chinese, Spanish, Turkish

Rev6， AS/NZ CISPR 32:2013

Safety: EN 60950-1, EN 60950-22, UL Listed to UL/CSA 60950-1, UL/CSA 60950-22

Entry to Enterprise Level Network Video Recorders (4.5 and greater)

greater)

Supported Web Browsers Internet Explorer (11.0+), Firefox, Chrome

Supported OS Windows 7, 32-bit/64-bit

Security

Languages

English, Arabic, Czech, Dutch, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian,

General

Input Voltage PoE+ (802.3at) Class 4, 12 VDC/24 VAC (±25%)

Power Consumption 18 W max. (with IR LEDs on and motorized lens working)

Dimensions 11.1 × 4.3 in. (281 × 110mm)

Weight 4.9 lb (2.2 kg)

Construction Die-cast aluminum housing with powder coat

Color RAL9003 (White) and RAL7022 (Gray)

Temperature –40°F to 140°F (–40°C to 60°C)

Relative Humidity Less than 95%, non-condensing

Ingress Protection IP67

Impact Resistance IK10

Regulatory

Emissions: EN 55032 ，

Immunity: EN 50130-4

ANSI C63.4-2014,ICE 003

RoHS: EN 50581

Integration

MAXPRO NVR Family

MAXPRO VMS Family

Entry to Enterprise Level Network Video VMS (R450 and

DVM DVM R620

HUS HUS 5.1 SP

Accessories

HBG-BB Back Box with Gasket HBG-FP Front Plate Replacement HB4G-PM Pole Mount Adapter HB34G-CM Corner Mount Adapter

Page 87

Technical Specifications

560/1024X452

Main Stream: 8M(4096x1800)/3840×1680 /2880×1264 (1~25fps)

NTP, RTP, RTCP,PPPOE,Bonjour,802.1x, Multi-cast

HM4L8GR1 Multi-Imager Dome Camera

Table A-3 HM4L8GR1 Specifications

Camera

Video Standard NTSC/PAL

Image Sensor

Number of Pixels (H×V) 4096 x 1800

Minimum Illumination 0.006Lux/F2.2( Color), 0Lux/F2.2(B/W, IR on)

Lens 5 mm/M12 (x4)

Horizontal Angle of View 180°

S/N Ratio 50 dB or more

Electronic Shutter Speed Auto, Manual, 1/3–1/100 000 s

IR Distance Up to 98 ft (30 m)

Day/Night Auto(ICR)/Color/BW

Backlight Compensation BLC/HLC/ DWDR

White Balance Auto/Natural/Street Lamp/Outdoor/Manual

Gain Control Auto/Manual

Noise Reduction 3DNR

Privacy Masking Up to 4 configurable areas

Audio Input/Output 1/1

Alarm Input/Output 2/2

Onboard Storage Up to 128 GB microSDHC card, Class 10 (not included)

Network

Video Compression H.265/H.264+/H.264/MJPEG

Resolution

1/1.9ʺ 2 MP progressive scan CMOS x4

8M(4096x1800)/3840×1680 /2880×1264/1920x832/1280x

Frame Rate

Audio Compression G.711a/G.711mu/AAC/G.726

Audio Stream Dual-Channel

Ethernet RJ-45 (100/1000Base-T)

Protocols

Compatibility ONVIF Profile S/G/Q

Max. Users 10 (Unicast)/20 (Multicast)

Supported Web Browsers Internet Explorer (11.0+), Firefox, Chrome

Supported OS Windows 7, 32-bit/64-bit

Sub Stream: 1024 x 452(1 ~ 25/30fps)

Triple Stream: 1920 x 832/1280x560 (1 ~ 25/30fps)

TCP/IP, UDP, ICMP, IPv4, IPv6, SNMP v2c/v3, QoS, HTTP, DHCP, HTTPS, SSL, SMTP, FTP, RTSP, UPnP, DNS, DDNS,

Page 88

Ultra HD IP Camera User Guide

RAL9003 (White)

Emissions: EN 55032 ， ANSI C63.4-2014,ICE 003 Rev6， AS/NZ CISPR 32:2013

Safety: EN 60950-1, EN 60950-22, UL Listed to UL/CSA 60950-1, UL/CSA 60950-22

Entry to Enterprise Level Network Video Recorders (4.5 and greater)

Entry to Enterprise Level Network Video VMS (R450 and greater)

Security

Multiple user access levels with enhanced password policy ,IP filtering, IEEE 802.1x, Strong Digest authentication for Access permission, Force to HTTPS with secure protocol TLS1.2 only and highly strength encrypted algorithm AES-256, SSH/Telnet closed & FTP disabled for reducing the surface being attacked, Comply with PCI-DSS , cyber-security...

Languages

General

Input Voltage PoE+ (802.3at) Class 4, 24 VAC (±25%)

Power Consumption 25 W max. (with IR LEDs on)

Dimensions 8.3 × 7.9 in. (212 × 201.6mm)

Weight 7.9 lb (3.6 kg)

Construction Die-cast aluminum housing with powder coat

Color

Temperature –40°F to 140°F (–40°C to 60°C)

Relative Humidity Less than 95%, non-condensing

Ingress Protection IP67

Impact Resistance IK10

Regulatory

Integration

English, Arabic, Czech, Dutch, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Simplified Chinese, Spanish, Turkish

Immunity: EN 50130-4

RoHS: EN 50581

MAXPRO NVR Family

MAXPRO VMS Family

DVM DVM R620

HUS HUS 5.1 SP

HDZJB Water-proof Junction Box HDZWM1 Wall Mount Bracket HDZWM2 Wall Mount Bracket with access hole

Accessories

HDZCMA Corner Mount Bracket HDZPMA Pole Mount Bracket HDZCM1 Ceiling Mount Bracket HDZCM2 220mm Extension Pole for HDZCM1 HDZCM3 420mm Extension Pole for HDZCM1

Page 89

Technical Specifications

8M(4096x1800)/3840×1680 /2880×1264/1920x832/1280x560/1024X452

(1~25fps)

TCP/IP, UDP, ICMP, IPv4, IPv6, SNMP v2c/v3, QoS, HTTP,

Multiple user access levels with enhanced password policy ,IP

hardware chipset for private key.

HMBL8GR1 Multi-Imager Bullet Camera

Table A-4 HMBL8GR1 Specifications

Camera

Video Standard NTSC/PAL

Image Sensor 1/2.8ʺ 2 MP progressive scan CMOS x4

Number of Pixels (H×V) 4096 x 1800

Minimum Illumination 0.008Lux/F2.1( Color), 0Lux/F2.1(B/W, IR on)

Lens 3 mm/M12(x4)

Horizontal Angle of View 180°

S/N Ratio 50 dB or more

Electronic Shutter Speed Auto, Manual, 1/3–1/100 000 s

IR Distance Up to 98 ft (30 m)

Day/Night Auto(ICR)/Color/BW

Backlight Compensation BLC/HLC/DWDR

White Balance Auto/Natural/Street Lamp/Outdoor/Manual

Gain Control Auto/Manual

Noise Reduction 3DNR

Privacy Masking Up to 4 configurable areas

Audio Input/Output 1/1

Alarm Input/Output 2/2

Onboard Storage Up to 128 GB microSDHC card, Class 10 (not included)

Network

Video Compression H.265/H.264+/H.264/MJPEG

Resolution

Frame Rate

Audio Compression G.711a/G.711mu/AAC/G.726

Audio Stream Dual-Channel

Ethernet RJ-45 (100/1000Base-T)

Protocols

Compatibility ONVIF Profile S/G/Q

Max. Users 10 (Unicast)/20 (Multicast)

Supported Web Browsers Internet Explorer (11.0+), Firefox, Chrome

Supported OS Windows 7, 32-bit/64-bit

Security

Main Stream: 8M(4096x1800)/3840×1680 /2880×1264

Sub Stream: 1024x452(1 ~ 25/30fps)

Triple Stream: 1920x832/1280x560 (1 ~ 25/30fps)

DHCP, HTTPS, SSL, SMTP, FTP, RTSP, UPnP, DNS, DDNS, NTP, RTP, RTCP,PPPOE,Bonjour,802.1x, Multi-cast

filtering, IEEE 802.1x, Strong Digest authentication for Access permission, Force to HTTPS with secure protocol TLS1.2 only and highly strength encrypted algorithm AES256, SSH/Telnet closed & FTP disabled for reducing the surface being attacked, Comply with PCI-DSS , cyber-security

Page 90

Ultra HD IP Camera User Guide

RAL9003 (White)

Emissions: EN 55032 ， ANSI C63.4-2014,ICE 003 Rev6， AS/NZ CISPR 32:2013

Safety: EN 60950-1, EN 60950-22, UL Listed to UL/CSA 60950-1, UL/CSA 60950-22

greater)

Entry to Enterprise Level Network Video VMS (R450 and greater)

Languages

General

Input Voltage PoE+ (802.3at) Class 4, 24 VAC (±25%)

Power Consumption 25 W max. (with IR LEDs on)

Dimensions 11.7 × 6.7 x 4.7 in. (298 × 171 x 120mm)

Weight 6.4 lb (2.9 kg)

Construction Die-cast aluminum housing with powder coat

Color

Temperature –40°F to 140°F (–40°C to 60°C)

Relative Humidity Less than 95%, non-condensing

Ingress Protection IP67

Impact Resistance IK10

Regulatory

Integration

MAXPRO NVR Family

English, Arabic, Czech, Dutch, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Simplified Chinese, Spanish, Turkish

Immunity: EN 50130-4

RoHS: EN 50581

Entry to Enterprise Level Network Video Recorders (4.5 and

MAXPRO VMS Family

DVM DVM R620

HUS HUS 5.1 SP

Accessories

HDZJB Water-proof Junction Box HDZCMA Corner Mount Bracket HDZPMA Pole Mount Bracket

Page 91

Index

Numerics

3DNR (3D digital noise reduction), 17

802.1X, 38

account settings, 63–67 adaptive screen mode, 8 AF Max 9 AF Peak 9 alarm output button, 9 alarm recording, 13,56 alarms

manually generating/canceling alarm output, 9

settings, 41–42 analog output, 60 anti-flicker, 17 ARP/ping, 29 audio

enabling/disabling audio input, 9

enabling/disabling bidirectional talk, 9

event detection, 49–50

properties, 26 audio button, 9 authority list, 64 auto delete, 69 auto focus, 8, 25 auto reboot, 69

backing up

configurations,68

logs,71 batch firmware upgrading, 4 bit rate, 21 BLC (backlight compensation), 17 Bonjour, 37 brightness, 8, 16

camera profile, 16, 19 camera specifications, 73–80 camera version information,69 CBR (constant bit rate), 21 certificates, 39 configuration settings

backing up,

restoring, 68 contrast, 8, 16 creating

user accounts, 66

user groups, 64

creating video clips, 14

date and time settings, 61-62 day and night settings, 18 DDNS (Dynamic DNS), 32 default settings, restoring, 68 defocus detection, 47 defog, 19 deleting

logs, 71 user accounts, 67

user groups, 65 device name, 60 digital zoom, 9 downloading

snapshots, 15

video clips, 14

video files, 14 DST (daylight saving time), 61

easy focus button, 9 EIS (electronic image stabilization), 17 email settings, 35

Page 92

Ultra HD IP Camera User Guide

events

alarm, 41–42 audio 49–50 camera tampering, 47–48 capacity warning, 43 illegal access, 44 IP conflict, 43 motion detection, 45–47 network disconnection, 43 no SD card, 43

scene change, 48 SD card error, 43 system, 43–45

exposure settings, 17

firmware

upgrading, 4, 69

version, 69 flip image, 17 fluency, 8 focusing 8 frame rate, 21 FTP storage, 58 full screen mode, 8

gamma, 16 general video recording, 13, 56 groups

assigning permissions, 64

creating, 64

deleting, 65

modifying, 65

H.264 (Main Profile), 20 H.264B (Baseline Profile),20 H.264H (High Profile), 20 HLC (highlight compensation),17 holiday schedule, 56 HTTP, 30

hue,

I-frame interval, 21 illegal access event settings,44 image adjustment panel, 8 image orientation, 17 image stabilization,17 IP address settings,28 IP filter settings, 33–34

-49

IPC Tool

assigning new IP address using, 4 discovering cameras using, 3 installing, 3 upgrading firmware using, 4

IVS (intelligent video surveillance), 8, 45–53

language, 60 latency, 10 list of symbols, v live interface

configuring, 8 controls, 8, 9

overview, 7 live video streaming setup, 10, 19 local storage, 57 login failure, 44 logs

backing up, 71

deleting, 71

viewing, 70

main stream, 10, 19 maintenance settings, 69 manual recording, 13 microphone. See audio mirror image, 17 MJPEG, 20 modifying

user accounts, 67

user groups, 65 motion detection recording, 13,56 motion detection settings, 45–47 multicast,

10, 38

NAS (network attached storage), 58 network

event settings, 43

IP settings, 28

maximum connections, 30

port settings, 30

security. See certificates

NTP (network time protocol),61

online users, 72 ONVIF (Open Network Video Interface Forum), 31 original screen mode, 8

panic save, 58

Page 93

picture settings

at camera end, 16

at client end, 8 playback controls, 12, 13 playback interface, 11 playing back video, 13 PPPoE (Point-to-Point Protocol over Ethernet), 31 privacy masks, 22 profile management, 19 protocols, 10

QoS (Quality of Service), 39

record button, 9 recording

path, 57

periods, 56

schedule, 56

settings, 59

storage, 56–58

type, 13 related documents, 2 resetting camera to defaults,68 resolution, 21 restoring

configuration, 68

factory defaults 68 ROI (regions of interest), 24 RTSP, 30

safety instructions, 80 saturation, 8, 16 scene change settings, 8, 48–49 screen modes, 8 SD card events,43 serial number, 69 sharpness, 16 smoothing. See fluency SMTP. See email settings snapshots

configuring settings, 21

downloading, 15

schedule, 56 taking snapshots of live video, 9 taking snapshots of recorded video,15 viewing, 15

SNMP (Simple Network Management Protocol),37 specifications, 73–80 status LED, 61 stream properties, 19 stream protocols, 10 stream type, 10 sub stream 1, 10, 19

sub stream 2, 10, 19 symbols used in document, v system event settings, 43–45

talk button, 9 tampering detection settings, 47–48 TCP, 10, 30 TCP/IP, 28 timeline

controls, 13 zooming in/out, 13

triple snapshot button, 9

UDP, 10, 30 upgrading firmware, 4, 69 UPnP (Universal Plug and Play), 36 user permissions, 64 users

assigning permissions, 66 creating, 66 deleting, 67 modifying, 67

VBR (variable bit rate), 21 video

creating clips, 14 day&night, 18 defog, 19 dowloading recorded video, 14 exporting clips, 14 exposure, 17 fluency, 8 focusing, 8 format, 20 holiday schedule, 56 lighting compensation, 17 manually recording live video, 9 playing back recorded video, 13 recording properties, 59 regular schedule, 56 setting stream type, 10 snapshot schedule, 56 storage, 56–58 streaming properties, 19 taking snapshots of live video, 9 taking snapshots of recorded video, 15 watermark, 21 white balance, 18 zooming in/out, 8, 25

video clips

controls, 12 creating, 14 exporting, 14

Index

Page 94

Ultra HD IP Camera User Guide

video standard, 60 viewing logs, 70

warranty, iv watermark, 21 WDR (wide dynamic range),17

web client

logging in, 6 logging out, 10

white balance settings, 18

zoom and focus panel, 8 zooming in/out, 8, 9, 25

Page 95

Honeywell Security Products Americas (Head Office)

2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA

www.honeywell.com/security

 +1 800 323 4576

Honeywell Security Europe/South Africa

Aston Fields Road, Whitehouse Industrial Estate Runcorn, WA7 3DL, United Kingdom

www.honeywell.com/security/uk

 +44 (0) 1928 754 028

Honeywell Security Products Americas Caribbean/Latin America

9315 NW 112th Ave. Miami, FL 33178, USA

www.honeywell.com/security/clar

 +1 305 805 8188

Honeywell Security Asia Pacific

35F Tower A, City Center, 100 Zun Yi Road Shanghai 200051, China

www.asia.security.honeywell.com

 +86 21 2219 6888

Honeywell Security Middle East/N. Africa

Emaar Business Park, Sheikh Zayed Road Building No. 2, Office No. 301 Post Office Box 232362 Dubai, United Arab Emirates

www.honeywell.com/security/me

 +971 (0) 4 450 5800

Honeywell Security Northern Europe

Ampèrestraat 41 1446 TR Purmerend, The Netherlands

www.honeywell.com/security/nl

 +31 (0) 299 410 200

Honeywell Security Deutschland

Johannes-Mauthe-Straße 14 72458 Albstadt, Germany

www.honeywell.com/security/de

 +49 (0) 7431 801-0

Honeywell Security France

Immeuble Lavoisier Parc de Haute Technologie 3-7 rue Georges Besse 92160 Antony, France

www.honeywell.com/security/fr

 +33 (0) 1 40 96 20 50

Honeywell Security Italia SpA

Via della Resistenza 53/59 20090 Buccinasco Milan, Italy

www.honeywell.com/security/it

 +39 (0) 2 4888 051

Honeywell Security España

Avenida de Italia, n° 7, 2 C.T. Coslada 28821 Coslada, Madrid, Spain

www.honeywell.com/security/es

 +34 902 667 800

planta

Honeywell Security Россия и СНГ

121059 Moscow, UI, Kiev 7 Russia

www.honeywell.com/security/ru

 +7 (495) 797-93-71

www.honeywell.com/security

+1 800 323 4576 (North America only)

https://www.honeywellsystems.com/ss/techsupp/index.html

© 2017 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes. For patent information, see www.honeywell.com/patents.

Document 800-23496 – Rev A – 07/2017