Honeywell HB73 User Manual
Dimensions (mm)
※ This Weatherproof IR Camera is
designed for Ceiling or Wall Mounting
126.0
122.0
Simple to install
Outdoor
Surveillance Camera
COMPOSITION:
As surroundings darken, it switches
automatically from color to black-and-white
mode to enhance sensitivity.
62.0
150.0
78.0 101.5
75.0
Regulatory Notice
!
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1)This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules.These limits are
designed to provide reasonable protection against harmful interference in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and use in accordance with the instructions, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause interference, in which case the user will be
required to correct the interference at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION - When this camera is installed near equipment, like a wireless
communication device that emits a strong electromagnetic field, some
irregularity such as noise on the monitor screen may happen.
L-Wrench
Operation Manual
Bracket Mounting Screws
SPECIFICATIONS:
Model
Signal System
Scanning System
Scanning Frequency (H
Scanning Frequency (V
Image Sensor
Total / Effective Pixels No.
S / N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity (F1.2)
Electronic Shutter
White Balance
AGC/ BLC/ D&N/ FL
DSS
D-ZOOM
DNR
Input / Output Connector
Operrating Temperature
Storage Temperature
Power Consumption
Dimensions (WxHxD
Weight
Call 1.800.796.CCTV for sales, service and customer support.
)
)
)
www.honeywellvideo.com
NTSC PAL
NTSC : 525 Lines PAL : 625 Lines
15.734kHz 15.625kHz
59.94Hz 50Hz
410K 470K
0.3 Lux (color)/ 0.008 Lux (DSS On) / 0 Lux (IR LED On)
1/60 ~ 120,000 Sec. 1 /50 ~ 120,000 Sec.
Power (Red Jack), Video (Yellow Jack)
12VDC (10V~15V), 0.3A/3.6W (Max)
2 : 1 Interlace
1/3 inch SONY Super HAD CCD
50dB Min. (AGC Off)
550 TV Lines
1.0 Vp-p (75 Ohms, composite)
Vari-focal Lens (F=1.2, f=3.8~9.5mm)
Manual
Internal
Auto
On / Off Selectable
On / Off (Max 32 times)
On / Off (2 x)
AUTO
-10°C ~ 45°C
-20°C ~ 65°C
75 x 78 x 150mm
Approx. 800g
Need Help?
Sun Visor Fastener
• 1/3" Sony Super HAD CCD
• High Resolution: 550 TV Lines
• Auto White Balance
• AGC, BLC, Flickerless On/Off
• 3.8 - 9.5 mm DC Vari-focal Auto Iris Lens
• Super Digital Noise Reduction (SDNR)
• Electronic Sensitivity-up(DSS) On/Off
18
/
• Weatherproof Housing
• IP65
Rev 0 03
P/N:3810-0054S
HB73
r
o
M
l
o
o
C
d
(
y
a
D
•
n
o
i
t
i
d
n
o
c
t
h
g
i
L
)
a
-
t
w
o
L
e
)
•
o
d
e
Series
N
i
g
h
t
(
B
/
W
M
Operation
Manual
READ AND KEEP THIS
OPERATION MANUAL
PRECAUTIONS:
!
Do not install the camera in extreme
temperature conditions.
Do use the camera under conditions where
temperatures are within -10°C to 45°C.
Be especially careful with ventilation under
high temperatures.
!
Do not install the camera under unstable
lighting conditions.
Severe lighting change or flicker can cause
the camera to work improperly.
!
Do not drop the camera or subject
to physical shock.
It can cause malfunctions to occur.
!
Never point the camera into strong
light or the sun.
It can damage CCD.
!
Note
If there is a bright spot light in the scene,
smearing or blooming may occur.
Confirm that the power supply provides
sufficient power before connecting the
camera.
1
Bright Adjustment V.R
Used to adjust video output level of DC driven auto iris lens.
When the brightness control of the monitor does not operate correctly,
you can optimize the picture picture by controlling the DC level of camera.
CONNECTION:
Connecting to Monitor and Power
#
1
Video
(Yellow)
Power- 12VDC
(Red)
#
2
Video Output
GND
NAME AND FUNCTION:
1
3
2
54
12VDC Power Type
• The wire is polarized.
• Use 12VDC power source.
No.
#1
Video Output
#2
Power Input
Function
Terminal Color
Yellow
Red
12VDC(10V~15V), 0.3A(Max)
Vari-focal Lens Type
2
Photo Sensor
3
IR LED
850nm / 30°(18EA)
4
Zoom Handle
Used to adjust zoom magnification by
turning.
5
Focus Handle
Used to provide for accurate focusing
of object within the lens field of view.
Remark
1.0 Vp-p
CAMERA SET-UP:
a
Service Monitor Connecter:
Use service monitor connector
to set camera angle & focus
when installing.
J504
VR501
a
OFF
OFF
ON
J505
SW501
ON
1 2 3 4 5 6
D/N
AGC
BLC
TROUBLESHOOTING:
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem,
contact an authorized technician.
The image does not
appear on the screen.
The image on the
screen is dim.
The camera does not work
properly, the surface of the
camera case is hot, and a black
line appears on the screen.
The screen blinks a lot.
b
Function Selection Switch:
•BLC(Back Light Compensation)
ON/OFF
•AGC(Auto Gain Control) ON/OFF
•D/N(Day & Night) ON/OFF
•DSS(Digital Slow Shutter) ON/OFF
•D.Z(Digital Zoom) ON/OFF
ONONOFF
OFF
OFFONONONOFF
FLK
D.Z
DSS
b
Check the power source for the monitor and
•
camera and ensure that the voltage and polarity
are correct.
Check if the lens is stained. If dirty, clean the lens with
•
a soft, clean cloth.
Adjust the Back Focus of the lens again.
•
Check if you have connected the camera to a proper
•
power source and If there is no problem with the power,
turn the unit off immediately and seek assistance from
our
Customer Service department
Check if the camera is pointed toward the sun or a
•
fluorescent lamp.
Adjust the angle or location of the camera if too much
•
light is coming into the screen.
•FLK(Flickerless) ON/OFF
CAUTION
D/N does not work because the
D/N switching function is
dependent on the AGC level.
: When AGC is off,
.
Loading...