Honeywell H3W2GR1V, H2W2GR1, H4L2GR1V, H3W4GR1V, HBL2GR1V User Manual

...

Download

Page 1

2MP/4MP Low Light WDR IP Camera

H4W2GR1V

H3W2GR1V

HBW2GR1V

HCL2GV

H2W2GR1

H4L2GR1V

H3W4GR1V

HBL2GR1V

HCW2GV

H4W4GR1V

HBW2GR3V

User Guide

Page 2

Page 3

Cautions and Warnings

CAUTION To ensure compliance with electrical safety standards, CSA

Listed LPS or Class 2 power adapters are required. Power over provided by listed information technology equipment standard. The PoE is not intended to be

CAUTION To comply with EN50130-4 requirements, a UPS should be

powering on the camera from 24 V AC.

CAUTION Installation and servicing should be performed only by qualified

experienced technicians to conform to all local codes and to maintain your

Regulatory Statements

FCC Compliance Statement

Information to the User: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Certified/UL

Ethernet (PoE) shall be

meeting the IEEE 802.3af PoE

connected to exposed (outside plant) networks.

employed when

and

warranty.

Changes or modifications not expressly approved by the party

Note

responsible for compliance could void the user’s authority to operate the equipment.

Canadian Compliance Statement

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.

Page 4

Manufacturer’s Declaration of Conformity

North America

The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-

Europe

The manufacturer declares that the equipment supplied is compliant with the European Parliament and Council Directive on the Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (2011/65/EU), General Product Safety Directive (2001/95/EC), and the essential requirements the EMC directive 2004/108/EC, conforming to the requirements of standards EN 55032 for emissions, EN 50130-4 for immunity, and EN 60950-1 for electrical equipment safety.

Waste Electrical and Electronic Equipment (WEEE)

Correct Disposal of this Product (applicable in the

European Union and other European countries with separate collection systems).

This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.

Safety Instructions

Before installing or operating the unit, read and follow all instructions. After installation, retain the safety and operating instructions for future reference.

1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.

2. INSTALLATION

• Install in accordance with the manufacturer’s instructions.

• Installation and servicing should be performed only by qualified and experienced

technicians to conform to all local codes and to maintain your warranty.

• Do not install the unit in an extremely hot or humid location, or in a place subject to

dust or mechanical vibration. The unit is not designed to be waterproof. Exposure to rain or water may damage the unit.

• Any wall or ceiling mounting of the product should follow the manufacturer’s

instructions and use a mounting kit approved or recommended by the manufacturer.

3. POWER SOURCES - This product should be operated only from the type of power source

indicated on the marking label. If you are not sure of the type of power supplied to your facility, consult your product dealer or local power company.

4. HEAT - Situate away from items that produce heat or are heat sources such as radiators,

heat registers, stoves, or other products (including amplifiers).

5. WATER AND MOISTURE - (Indoor models only) Do not use this unit near water or in an

unprotected outdoor installation, or any area classified as a wet location.

Page 5

6. MOUNTING SYSTEM - Use only with a mounting system recommended by the

manufacturer, or sold with the product.

7. ATTACHMENTS - Do not use attachments not recommended by the product

manufacturer

as they may result in the risk of fire, electric shock, or injury to persons.

8. ACCESSORIES - Only use accessories specified by the manufacturer.

9. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for

10. SERVICING - Do not attempt to service this unit yourself as opening or removing covers

cleaning.

may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

11. REPLACEMENT PARTS - When replacement parts are required, be sure the service

technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. Using replacement parts or accessories other than the original manufacturers may invalidate the warranty.

12. DAMAGE REQUIRING SERVICE - Unplug the unit from the outlet and refer servicing to

qualified service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the unit.

• If the unit has been exposed to rain or water.

• If the unit does not operate normally by following the operating instructions. Adjust

only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.

• If the unit has been dropped or the enclosure has been damaged.

• When the unit exhibits a distinct change in performance - this indicates a need for

service.

13. SAFETY CHECK - Upon completion of any service or repairs to this unit, ask the service

technician to perform safety checks to determine that the unit is in proper operating condition.

Warranty and Service

Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid.

In the event you have a problem with any Honeywell product, please call Customer Service at

1.800.323.4576 for assistance or to request a Return Merchandise Authorization (RMA) number. Be sure to have the model number, serial number, and the nature of the problem available for the technical service representative.

Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to Honeywell without a clearly identified Return Merchandise Authorization (RMA) number may be refused.

iii

Page 6

List of Symbols

The following table contains a list of symbols that may appear on the camera:

Symbol Explanation

The WEEE symbol.

This symbol indicates that when the end-user wishes to discard this product, it must be sent to separate collection facilities for recovery and recycling. By separating this product from other household-type waste, the volume of waste sent to incinerators or landfills will be reduced, and thus natural resources will be conserved.

The UL compliance logo.

This logo indicates that the product has been tested and is listed by the Underwriters Laboratories.

The FCC compliance logo.

This logo indicates that the product conforms to Federal Communication’s Commission compliance standards.

The direct current symbol.

This symbol indicates that the power input/output for the product is direct current.

The alternating current symbol.

This symbol indicates that the power input/output for the product is alternating current.

The RCM Compliance symbol.

This symbol indicates that the product conforms with the Australian RCM guidelines.

The CE Compliance logo.

This logo indicates that the product conforms to the relevant guidelines/standards for the European Union harmonization legislation.

This symbol is used to direct attention to important information.

The Protective Earth symbol.

This symbol indicates that the marked terminal is intended for connection to the protective earth/grounding conductor.

Page 7

Contents

About This Document ....................................................................................................................................................... viii

Overview of Contents .......................................................................................................................................................... viii

1 Accessing the Camera .......................................................................................................................................... 1

Installing the IPC Tool Utility .............................................................................................................................................. 1

Discovering Your Camera on the Network ................................................................................................................... 1

Assigning a New IP Address to Your Camera ............................................................................................................. 1

Upgrading the Camera’s Firmware ................................................................................................................................. 2

Accessing the Camera from a Web Browser ............................................................................................................... 2

2 Logging In and Viewing Live Video ................................................................................................................. 4

Logging In to the Web Client ............................................................................................................................................. 4

Overview of the Live Interface ............................................................................................................................................ 5

Configuring the Live Interface .......................................................................................................................................... 6

Working in the Live Interface ............................................................................................................................................. 7

Setting Up Live Video Streaming ..................................................................................................................................... 8

Setting the Stream Type Setting the Stream Protocol

Logging Out of the Web Client.......................................................................................................................................... 8

3 Playing Back Recorded Video ........................................................................................................................... 9

Overview of the Playback Interface ................................................................................................................................. 9

Playback Controls Video Clip Controls

Timeline ............................................................................................................................................................................. 10

Playing Back Recorded Video ......................................................................................................................................... 11

Downloading Recorded Video ........................................................................................................................................ 11

Viewing Snapshots .............................................................................................................................................................. 12

..................................................................................................................................................... 8

............................................................................................................................................. 8

................................................................................................................................................................ 9

........................................................................................................................................................... 10

4 Configuring Video and Audio Settings ........................................................................................................ 14

Configuring Video Settings .............................................................................................................................................. 14

Configuring Camera Settings

Managing Profiles

Configuring Streaming Settings

Configuring Snapshot Settings

Configuring Privacy Masks

Configuring the Channel Title

Configuring the Time Title

Configuring Customized Text Overlays

Configuring Picture Overlays

Configuring Regions of Interest

Configuring Zoom and Focus Settings

Configuring Audio Settings ............................................................................................................................................. 24

5 Configuring Network Settings ........................................................................................................................ 26

Configuring TCP/IP ............................................................................................................................................................. 26

IPv4 Address Configuration

IPv6 Address Configuration

ARP/Ping

Configuring Network Connections ............................................................................................................................... 28

Configuring ONVIF .............................................................................................................................................................. 29

............................................................................................................................................................................. 27

............................................................................................................................................................ 17

........................................................................................................................................ 14

................................................................................................................................... 18

.................................................................................................................................... 19

............................................................................................................................................ 20

....................................................................................................................................... 21

.............................................................................................................................................. 22

...................................................................................................................... 22

........................................................................................................................................ 23

................................................................................................................................... 23

....................................................................................................................... 23

........................................................................................................................................... 27

Page 8

Configuring RSTP ................................................................................................................................................................ 29

Configuring PPPoE Settings ........................................................................................................................................... 30

Configuring DDNS Settings ............................................................................................................................................ 30

Filtering IP/MAC Addresses ............................................................................................................................................ 31

Adding IP/Mac Addresses to the List of Approved Users

Editing IP/Mac Addresses

Deleting IP/Mac Addresses from the List of Approved Users

Configuring Email Settings ............................................................................................................................................. 33

Configuring UPnP Port Mapping .................................................................................................................................. 34

Configuring SNMP Settings ............................................................................................................................................ 35

Configuring Bonjour ........................................................................................................................................................... 36

Configuring Multicast Settings ..................................................................................................................................... 36

Configuring 802.1X Settings .......................................................................................................................................... 37

Configuring QoS Settings ................................................................................................................................................ 37

Working with Certificates .................................................................................................................................................. 38

Importing Certificates ................................................................................................................................................. 38

Certificate Request ....................................................................................................................................................... 39

6 Configuring Event Settings ............................................................................................................................. 40

Configuring Alarm Events ................................................................................................................................................ 40

Configuring System Events ............................................................................................................................................. 42

Configuring SD Card Event Settings

Configuring Network Event Settings

Configuring Illegal Access Event Settings

Configuring Motion Detection Events ........................................................................................................................ 44

Configuring Camera Tampering Events .................................................................................................................... 46

Configuring Scene Change Events .............................................................................................................................. 47

Configuring Audio Events ................................................................................................................................................ 48

Configuring Smart Plan .................................................................................................................................................... 49

Configuring IVS Analysis Events .................................................................................................................................. 50

Configuring Face Detection Events ............................................................................................................................. 51

Configuring People Counting Events ........................................................................................................................ 52

People Counting ............................................................................................................................................................ 52

Report ................................................................................................................................................................................. 53

Configuring Heat Map Events ....................................................................................................................................... 54

............................................................................................................................................. 32

........................................................................................................................... 42

................................................................................................................. 43

...................................................................................... 32

.............................................................................. 33

7 Intelligent Analytics System ........................................................................................................................... 55

8 Configuring Recording Settings .................................................................................................................... 56

Configuring Recording Schedules ............................................................................................................................... 56

Configuring Storage Settings ......................................................................................................................................... 57

Configuring Storage Paths

Configuring the Local SD Card for Storage

Configuring an FTP Server for Storage

Configuring an NAS Disk for Storage

Configuring Recording Settings .................................................................................................................................... 59

9 Configuring System Settings .......................................................................................................................... 61

Configuring General System Settings ........................................................................................................................ 61

Configuring Date and Time Settings ........................................................................................................................... 61

Changing the Date and Time Format

Setting the Date and Time

Configuring Account Settings ........................................................................................................................................ 63

Managing Groups

Managing Users

............................................................................................................................................................. 63

................................................................................................................................................................ 65

............................................................................................................................................ 57

............................................................................................................... 58

....................................................................................................................... 58

.......................................................................................................................... 59

......................................................................................................................... 62

............................................................................................................................................... 62

Page 9

Resetting the Camera......................................................................................................................................................... 67

Backing Up/Restoring a Configuration ..................................................................................................................... 68

Configuring Maintenance Settings ............................................................................................................................. 68

Upgrading the Firmware ................................................................................................................................................... 69

Viewing Version Information ........................................................................................................................................... 69

Managing Logs ..................................................................................................................................................................... 70

Viewing Logs

Backing Up Logs

Deleting Logs

Viewing Online Users .......................................................................................................................................................... 71

10 Appendix A Technical Specifications ........................................................................................................... 73

HBW2GR3V/HBW2GR1V/HBL2GR1V Bullet Camera ...................................................................................... 73

HCL2GV/HCW2GV Box Camera .................................................................................................................................. 76

H3W2GR1V/H3W4GR1V Indoor Dome Camera .................................................................................................. 79

H4W2GR1V/H4L2GR1V/H4W4GR1V Outdoor Dome Camera ................................................................... 82

H2W2GR1 Micro Dome Camera .................................................................................................................................. 84

...................................................................................................................................................................... 70

............................................................................................................................................................... 71

..................................................................................................................................................................... 71

vii

Page 10

Page 11

About This Document

This manual is intended for system installers, administrators, and users of Honeywell’s equIP® Series 2MP/4MP LOW LIGHT WDR IP cameras and contains instructions for accessing, configuring, and operating the cameras.

Overview of Contents

This manual contains the following chapters and appendixes:

• Chapter 1, Accessing the Camera, describes how to access the camera remotely from a web

browser.

• Chapter 2, Logging In and Viewing Live Video, describes how to log in to the camera and how

to use the Live interface.

• Chapter 3, Playing Back Recorded Video, describes how to play back and export recorded

video and snapshots.

• Chapter 4, Configuring Video and Audio Settings, describes how to set up video and audio

streams.

• Chapter 5, Configuring Network Settings, describes how to set up the camera on a network.

(For advanced users only.)

• Chapter 6, Configuring Event Settings, provides instructions for configuring alarm

inputs/outputs, motion detection, audio detection, tampering detection, and system event settings.

• Chapter 7, Intelligent Analytics System, describes how to access the Intelligent Analytics

System.

• Chapter 8, Configuring Recording Settings, describes how to set up a recording schedule

and how to manage recording and storage settings.

• Chapter 9, Configuring System Settings, provides instructions for configuring language and

date and time options, managing user accounts and permissions, setting maintenance tasks, upgrading firmware, and resetting a camera to its factory defaults.

• Chapter 10, Appendix A Technical Specifications, lists camera specifications.

Page 12

Page 13

1 Accessing the Camera

This chapter contains the following sections:

• Installing the IPC Tool Utility, page 1

• Discovering Your Camera on the Network, page 1

• Assigning a New IP Address to Your Camera, page 1

• Upgrading the Camera’s Firmware, page 2

• Accessing the Camera from a Web Browser, page 2

Installing the IPC Tool Utility

To install the IPC Tool utility and create a desktop shortcut:

1. Insert the included Software and Document disc into your PC’s disc drive.

Accessing the Camera

2. Install the IPC Tool utility to your PC. The shortcut is added to the desktop.

Discovering Your Camera on the Network

To discover your network camera(s), open the IPC Tool utility , enter your user name and password, and then click Connect. Cameras that are online have a green connected icon

next to them. Cameras that are offline have a gray X next to them. To refresh the list, click Refresh.

Assigning a New IP Address to Your Camera

The current IP address of your camera appears in the IP column of the devices list. If you want, you can assign a new static IP address to the camera.

To change the IP address of a single camera:

1. Select the camera that you want to configure from the devices list.

Page 14

2MP/4MP Low Light WDR IP Camera User Guide

2. Click the Network tab.

3. Clear the DHCP check box.

4. Enter the new IP settings in the IP Address, Subnet Mask, and Default Gateway fields.

5. Click Apply to apply the settings.

To change the IP addresses of multiple cameras at the same time:

1. In the left-most pane of the IPC Tool utility, click Batch Setting.

2. Select all of the cameras that you want to configure from the devices list.

3. Click the Network tab.

4. Do one of the following:

• To assign dynamic IP addresses, select the Set all to DHCP check box, and then click Apply.

• To assign static IP addresses, enter the settings in IP Range, Subnet Mask, and Default Gateway fields, and then click Apply.

Upgrading the Camera’s Firmware

Before you begin using your camera, make sure you have the latest firmware installed. You can upgrade a single camera or multiple cameras at the same time.

To upgrade a single camera:

1. Select the camera that you want to upgrade from the devices list.

2. Click the Upgrade tab.

3. Click Browse, navigate to the directory that contains the firmware file (.bin), select the file, and then click Open. The firmware file appears in the Target File field.

4. Click Upgrade. When the upgrade is complete, the camera will reboot.

To upgrade multiple cameras at the same time:

1. In the left-most pane of the IPC Tool utility, click Batch Setting.

2. Select all of the cameras that you want to upgrade from the devices list.

3. Click the Upgrade tab.

4. Click Browse, navigate to the directory that contains the firmware file (.bin), select the file, and then click Open. The firmware file appears in the Target File field.

5. Click Upgrade. When the upgrade is complete, the cameras will reboot.

Accessing the Camera from a Web Browser

To access the camera from a web browser:

1. Select the camera that you want to access from the devices list. The camera must be online .

Page 15

Accessing the Camera

2. On the Device Information tab, click Web Page. The web client opens in your default browser.

Page 16

2MP/4MP Low Light WDR IP Camera User Guide

2 Logging In and Viewing Live Video

This chapter contains the following sections:

• Logging In to the Web Client, page 4

• Overview of the Live Interface, page 5

• Configuring the Live Interface, page 6

• Working in the Live Interface, page 7

• Setting Up Live Video Streaming, page 8

• Logging Out of the Web Client, page 8

Logging In to the Web Client

If this is your first time logging in to the web client, on the login page, enter the default user name (admin) and password (1234), and then click Login.

For security purposes, you are required to create a new secure password.

Page 17

The password must be at least 8 characters long and contain at least one lowercase letter, one number, and one special character. The password cannot be blank.

Overview of the Live Interface

The following figure shows the layout of the web client’s Live interface.

Figure 2-1 Live Interface

Logging In and Viewing Live Video

Page 18

2MP/4MP Low Light WDR IP Camera User Guide



Setup  Conditions  Picture.

determined by the stream resolution).

press Esc) to exit full-screen mode.

Ratio

your screen (Adaptive).

will prioritize smoothness over image quality.

video surveillance (IVS) is enabled.

Configuring the Live Interface

Note

You can configure the Live interface using the configuration controls located in the lower left corner of the screen, immediately below the video window.

Figure 2-2 Live Configuration Toolbar

Table 2-1 Live Configuration Controls

The first time you log into the web client, follow the on-screen instructions to download and install the web browser plug-in.

Image Adjustment

Opens the Image Adjustment panel. Move the sliders to adjust the image

brightness, contrast, hue, or saturation. Click the – and + signs to make fine adjustments. To restore the settings to their default values (64), click Reset.

Note These settings only apply to the client end. To change the settings at the camera end, go to Setup

Camera

Original Size Displays the video at actual size (the exact dimensions are

Full Screen Displays the video in full-screen mode. Double-click (or

Width:Height

Fluency Sets the video fluency level (Realtime, Normal, or Fluency).

Rules Info Tracks movement in the video window when intelligent

Displays the video in its original size (Original) or fitted to

Select a fluency level based on the capabilities of your network.

For example, if your connection is slow, selecting Fluency

Page 19

window.

also be enabled).

focused manually.



Record.



Snapshot.



Setup  Destination  Path  Live Snapshot.

return to the previous magnification.

Logging In and Viewing Live Video

Zoom and Focus

Opens the Zoom and Focus panel. Move the sliders to adjust the zoom

and focus settings. Click the – and + signs to make fine adjustments. The Step number determines the magnitude of the adjustment. To set the focus automatically, click Auto Focus. To restore the default zoom and focus settings, click Restore All. To focus on a specific region, click Regional Focus, and then drag your mouse over the area in the video

Working in the Live Interface

The toolbar in the upper left corner of the screen, immediately above the video window, provides quick access to commonly used controls.

Figure 2-3 Quick Access Toolbar

Table 2-2 Quick Access Controls

Talk

Click to enable or disable bidirectional talk (audio must

Audio Click to enable or disable the audio input stream.

Easy Focus

Displays the current video definition (AF Peak) and target video definition (AF Max). For auto focus to work, the AF Peak and AF Max values must be close together. If the values are far apart, the camera must be re-aimed or

Record Click to start or stop recording video. The icon appears red

when video is being recorded, gray when video is not being recorded.

The recorded video is saved to the location specified in

Storage Setup  Destination  Path  Live

Triple Snapshot

Setup

Click to take three snapshots in quick succession (1 per second). The snapshots are saved to the location specified in Setup

Snapshot

Click to take a snapshot of the current video. The snapshot is saved to the location specified in Setup

Storage

Digital Zoom

When this function is enabled, you can drag your mouse over an area of the video to enlarge that area. Right-click to

Page 20

2MP/4MP Low Light WDR IP Camera User Guide

is inactive.

Delivers storage. Uses the most bandwidth.

Delivers in lower network bandwidth environments.

Sub Stream 2

Delivers low, standard, or high definition video.

Provides use than UDP.

Provides than TCP but allows some data loss (such as dropped frames).

Provides are viewing the video simultaneously.

Alarm Output

Help Displays online help for the Live interface.

Click to generate or cancel an alarm output. The icon appears red when the alarm is active, gray when the alarm

Setting Up Live Video Streaming

In the upper right corner of the screen, immediately above the video window, you can set the stream type and protocol for live video streaming.

Setting the Stream Type

To set the stream type, in the Stream Type list, select Main Stream, Sub Stream 1, or Sub Stream 2.

Main Stream

Sub Stream 1

high definition video for real-time monitoring, recording, and

low/standard definition video, typically for remote monitoring

The properties for each stream type are configured on the Setup > Compression Setup > Video page (see Configuring Streaming Settings on page 18).

Setting the Stream Protocol

To set the stream protocol, in the Protocol list, select TCP, UDP, or Multicast.

TCP

UDP

Multicast

most reliable data transmission. Higher latency and bandwidth

fastest data transmission. Lower latency and bandwidth use

the most efficient use of bandwidth if large numbers of clients

Logging Out of the Web Client

To log out of the web client, in the upper right corner of the screen, click Logout.

Page 21

Playing Back Recorded Video

3 Playing Back Recorded Video

This chapter contains the following sections:

• Overview of the Playback Interface, page 9

• Playing Back Recorded Video, page 11

• Downloading Recorded Video, page 11

• Viewing Snapshots, page 12

Overview of the Playback Interface

The following figure shows the layout of the web client’s Playback interface.

Figure 3-1 Playback Interface

Playback Controls

The playback controls are located in the lower left corner of the screen, immediately below the video window. For instructions on how to play back video, see Playing Back Recorded Video on page 9.

Page 22

2MP/4MP Low Light WDR IP Camera User Guide

paused.

local drive on your PC.

Figure 3-2 Playback Toolbar

Table 3-1 Playback Controls

Play/Pause Click to play recorded video.

Pause Click to pause playback.

Stop Click to stop playback.

Next Frame

Slow Play Click to slow down playback.

Fast Play Click to speed up playback.

Volume Click to enable sound.

Mute Click to disable sound.

Volume Level Drag the slider to adjust the sound volume.

Video Clip Controls

The video clip controls are located in the lower right corner of the screen, immediately below the file list button. For instructions on how to create and export a video clip, see Downloading

Recorded Video on page 11.

Figure 3-3 Video Clip Area

Table 3-2 Video Clip Controls

Clip Click to start/stop clipping video.

Download

Click to advance to the next frame when playback is

Click to download the video clip that you have created to a

Timeline

The timeline is located below the playback and video clip controls.

Figure 3-4 Timeline Area

Page 23

in the timeline.

the timeline.

Alarm

Displays video saved during an alarm event in the timeline.

the timeline.

24hr

Displays 24 hours of video in the timeline.

2hr

Displays 2 hours of video in the timeline.

1hr

30min

Displays 30 minutes of video in the timeline.



the timeline), and then click the Play button.

Table 3-3 Timeline Controls

Playing Back Recorded Video

Record Type General

Displays video saved during normally scheduled recording

Motion Displays video saved during a motion detection event in

Manual Displays video saved manually during live monitoring in

Displays 1 hour of video in the timeline.

Playing Back Recorded Video

To play back recorded video:

1. From the File Type list, select dav.

2. From the Data Src list, select the location where the video files

are stored.

The storage location is configured in Setup  Storage Setup

Destination (see Configuring Storage Settings on page 57).

3. Locate the file that you want to play back.

a. Above the calendar, select the month and year that you

want to search.

b. On the calendar, click the date that you want to search.

Recordings for the selected date appear in the timeline (color coded according to recording type).

c. Below the calendar, click the File List button to narrow

your search by time period and/or by download format.

4. Play the file using one of the following methods:

• In the file list, double-click the file that you want to play.

• In the timeline, click a colored bar at the time that you

want to start playing from

(click

Downloading Recorded Video

There are two ways to download recorded video: you can download a complete video file (the maximum length is specified in Setup and export a video clip that you have created.

 Storage Setup  Record Control) or you can create

to zoom in on

To download a video file:

Page 24

2MP/4MP Low Light WDR IP Camera User Guide

1. From the File Type list, select dav.

2. From the Data Src list, select the location where the video files are stored.

3. On the calendar, click the date that the video was recorded.

4. Click File List to display the list of video files for that date.

5. Set the Download Format to dav or mp4.

6. From the file list, click the download button of the file that you want to download.

The button changes to and the file is saved to the location specified in Setup 

Compression Setup

 Path  Playback Download.

To create and export a video clip:

1. Open a video file in the playback window.

2. Pause the video at the time when you want to start the clip.

3. In the video clip area, click the Select Start Time button .

4. Resume playing the video.

5. Pause the video at the time when you want to stop the clip.

6. Click the Select Stop Time button .

7. Stop the video, and then click the Download button .

Note

You cannot download the clip while the video file is still open in the web client.

The clip is saved to the location specified in Setup  Compression Setup  Path  Video Clips.

Viewing Snapshots

You can take snapshots of video during playback by clicking the Snapshot button . The snapshot is saved to the location specified in Setup

Playback Snapshot.

 Compression Setup  Path 

To view a snapshot that you have saved manually during live monitoring, go the directory specified in Setup

 Compression Setup  Path  Live Snapshot and double-click the file

to open it.

Page 25

Playing Back Recorded Video

To view a snapshot that you have saved manually during playback, go the directory specified in

Setup

 Compression Setup  Path  Playback Snapshot and double-click the file to open

it.

If you have configured the system to take snapshots on a schedule, or during motion detection or alarm events, you can view and download them.

To view or download a system-generated snapshot:

1. From the File Type list, select jpg.

2. From the Data Src list, select the location where the snapshot files are stored.

3. On the calendar, click the date that the snapshot was taken.

4. Click File List to display the list of snapshots for that date.

5. Double-click the snapshot file that you want to view. The file opens in the video window.

6. To download the file, click the download button . The file opens in a new browser

window. Right-click the image and then click Save picture as or Save image as to save the snapshot to a local directory.

Page 26

2MP/4MP Low Light WDR IP Camera User Guide

image.

4 Configuring Video and Audio Settings

This chapters contains the following sections:

• Configuring Video Settings, page 14

• Configuring Audio Settings, page 24

Configuring Video Settings

This section describes how to configure camera properties (picture, exposure, lighting compensation, white balance, day and night, IR light, and defog) and video streaming properties (format, resolution, frame rate, bit rate, and I-frame interval).

Configuring Camera Settings

You can configure camera properties on the Setup  Camera Setup  Properties page.

Profile

In the Profile list, select the camera profile that you want to configure settings for: Normal, Day, or Night.

Picture

In the Picture area, select a picture style from the Style list: Soft, Standard, or Vivid.

To adjust the image brightness, contrast, saturation, sharpness, or gamma settings, drag the slider left or right or click the – and + signs to make fine adjustments.

Brightness

Contrast

Saturation Adjusts the intensity of the image colors.

Sharpness

Keep in mind that increasing create more noise, resulting in a larger bit file size.

Adjusts the black level of the image.

Adjusts the white level of the image.

Adjusts the edge sharpness of image elements.

sharpness in a moving image will

stream and saved

Gamma

the image. Use fine

You can also change the image orientation:

• To reverse the image, set Mirror to ON.

Adjusts the amount of gamma correction applied to

adjustments to accent darker areas of the

Page 27

• To rotate the image 90 degrees, 180 degrees, or 270 degrees, set AOV to 90° (Flip Mode

Configuring Video and Audio Settings

1), 180° Inverted, or 270° (Flip Mode 2) respectively.

If the camera is mounted on a pole or in an environment subject to vibration, you can set EIS (Electronic Image Stabilization) to ON to improve image stability. Click Save to apply the settings.

Exposure

In the Exposure area, you can set the anti-flicker mode, exposure mode, auto iris, and digital noise reduction level.

Set Anti-Flicker to Outdoor, 50Hz, or 60Hz.

Outdoor

50Hz

Minimizes flicker in outdoor applications. Works with auto, low noise, low motion

blur, and manual exposure modes

Minimizes flicker in indoor applications where the AC frequency is 50 Hz

(generally PAL regions). Works with auto and manual

exposure modes.

60Hz

Minimizes flicker in indoor applications where the AC frequency is 60 Hz

(generally NTSC regions). Works with auto and manual

exposure modes.

Set Mode to Auto, Gain Priority, Shutter Priority, Iris Priority, or Manual.

Auto

Exposure settings change automatically with changes in the scene's

lighting.

Gain Priority The shutter speed and iris are adjusted automatically for the specified

value.

gain

Shutter Priority The iris and gain are adjusted automatically for the specified shutter speed.

Iris Priority The shutter speed and gain are adjusted automatically for the specified

iris

value.

Manual

Maximum shutter speed and maximum gain for normal light conditions are

set by the user.

3DNR (3D noise reduction) is enabled by default. Drag the Grade slider left or right to decrease or increase the level of digital noise reduction applied to the image. To disable 3D noise reduction, set 3DNR to OFF.

Click Save to apply the settings.

Lighting Compensation

In the Lighting Compensation area, you can apply backlight compensation (BLC), highlight compensation (HLC), wide dynamic range (WDR), or scene adaptive control (SAC) adjustment to the image.

Set Lighting Mode to OFF, BLC, HLC, WDR, or SAC.

BLC

HLC

Corrects the exposure of strongly backlit scenes. To apply BLC to the entire scene, Customized. A drag the center of the

click Default. To apply BLC to a specific area of the scene, click

yellow rectangle appears in the preview window. To move it,

frame. To resize it, drag one of the corner handles.

Masks strong light sources in the scene. Drag the slider to adjust the HLC level.

Page 28

2MP/4MP Low Light WDR IP Camera User Guide

Click the – and + signs to make fine adjustments.

WDR

SAC

Click Save to apply the settings.

Corrects the exposure of overexposed and underexposed areas of the scene.

the slider to adjust the WDR level. Click the – and + signs to make fine

Drag adjustments.

Automatically decreases the brightness of bright areas and increases

brightness of dark areas according to the environmental lighting.

the

White Balance

White balance compensates for the different color temperatures of different light sources, ensuring consistent colors- in the image.

In the White Balance area, you can set the white balance mode to Auto, Natural, Street Lamp, Outdoor, Manual or Customize Region.

Auto

Natural

Street Lamp White balance is optimized for yellow-tinted lighting.

Outdoor

Manual

Customize Region White balance is applied to a user-defined area within the scene.

Click Save to apply the settings.

White balance is adjusted automatically.

White balance is optimized for natural lighting.

White balance is optimized for outdoor environments.

Red gain and blue gain values are set by the user.

Day and Night

In the D&N Mode area, you can set the day and night mode, sensitivity, and delay time.

By default, the camera automatically outputs color video or black-and-white video depending on the amount of light in the scene. To output only color video, set Mode to Color. To output

only black-and-white video, set Mode to Black & White.

Sensitivity controls the sensitivity to lighting changes that cause the camera to switch between day (color) and night (black-and-white) mode. Select Low, Medium, or High.

Delay defines the delay time before switching between modes. Select a value between 2s and 10s.

Smart IR function is disabled by default. To enable it, click ON. Click Save to apply the settings.

IR Light

In the IR Light area, you can set the infrared LED mode and other settings. Set Mode to Manual, Zoom Priority, Smart IR, or OFF.

Manual

Zoom Priority IR settings are adjusted automatically based on the zoom setting.

SmartIR

IR near and far distance brightness are set by the user.

IR settings are adjusted automatically to prevent overexposure or

Page 29

the Grade slider.

underexposure.

If Mode is set to Manual, set the Near Light and Far Light brightness levels. Drag the slider left or right to decrease or increase the value. Click the – and + signs to make fine adjustments.

If Mode is set to Zoom Priority, set the IR Correction level to correct focusing problems caused by bright IR light.

Configuring Video and Audio Settings

Defog

To enable the defog function, set Mode to OFF, Manual, or Auto.

Auto

Manual

If Mode is set to Manual, do the following:

1. Set Intensity to Low, Medium, or High.

2. Set Airlight Mode to Auto or Manual.

Auto

Manual

Click Save to apply the settings.

The defog function is enabled automatically when the scene is obscured by fog or

haze.

The defog function is always enabled.

The defog function is fine-tuned automatically (recommended).

The defog function is fine-tuned by the user using

Managing Profiles

After you have configured the camera properties for each profile (Normal, Day, Night), you can set the profile(s) that you want the system to use on the Setup Management page.

 Camera Setup  Profile

Next to Profile Management, select Normal, Full Time, or Schedule. By default, the system has the Day profile always enabled.

Normal

Full Time The Day profile or Night profile is always enabled, depending on your selection.

Schedule

Click Save to apply the settings.

The Normal profile is always enabled.

The system switches between the Day profile and Night profile. Drag the sliders on

the left and right sides of the timeline to set the Night-to-Day and Day-to-

Night

switching times.

Page 30

2MP/4MP Low Light WDR IP Camera User Guide

Configuring Streaming Settings

You can configure video streaming properties on the Setup  Compression Setup  Video page.

The page is divided into two sections: Main Stream and Sub Stream. In the Sub Stream section, two sub streams are configurable: Sub Stream 1 and Sub Stream 2. To enable a sub stream, select one of the sub streams, and then select the Enable check box.

For each record type (General, Motion, Alarm), you can configure the encoding format, resolution, frame rate, bit rate, and I-frame interval settings. You can also apply a custom watermark to the main stream.

Format

In the Format box, select H.264B, H.264, H.264H, MJPEG, or H.265.

H.264 Main Profile. Uses less bandwidth than Baseline Profile at the same quality.

H.264B

H.264H

MJPEG

H.265 High Efficiency Video Coding. Supports 4K resolution. Twice as efficient as H.264.

Baseline Profile. Uses up to 50% less bandwidth than MPEG4 and up to 80% less than MJPEG. Higher compression and lower quality than H.264.

High Profile. Uses less bandwidth than Main Profile at the same quality. Lower compression and higher quality than H.264.

Uses the most bandwidth but produces excellent image quality with access to every image in the stream.

Smart Codec

Set Smart Codec to ON or OFF.

By taking reference frames and applying them to refreshed frames, Smart Codec eliminates the need to transmit data for an unchanged image or parts of the image where there is no

Page 31

movement. Used together with H.264, Smart Codec can lead to storage savings of up to 60 percent and bandwidth savings of up to 40 percent over H.264 alone.

Configuring Video and Audio Settings

Note

If Smart Codec is set to ON, video analytics will be unavailable.

Resolution

In the Resolution box, select a resolution from the list. The available options differ between the main stream and sub streams.

Frame Rate

In the Frame Rate (FPS) box, select a frame rate within the available range (1–60 fps for NTSC cameras; 1–50 fps for PAL cameras).

Bit Rate

In the Bit Rate Type box, select CBR or VBR.

CBR

VBR

In the Bit Rate box, select a bit rate from the list using the Reference Bit Rate as a guide.

Constant bit rate. The bit rate remains constant (recommended for low-bandwidth environments). Required if MJPEG compression is used.

Variable bit rate. The bit rate changes according to the complexity of the scene. Select a Quality level between 1 (lowest quality) and 6 (highest quality).

I-Frame Interval

In the I-Frame Interval box, enter a value between 1 and 150. The default I-frame interval is two times the frame rate. For example, if the frame rate is 30 fps, the I-frame interval will be 60.

Watermark

To apply a custom watermark to the main stream, select the Watermark Settings check box. In the Watermark Text box, enter the watermark text. The text cannot have any spaces but underscores (_), and hyphens (-) are acceptable.

Click Save to apply the settings.

Configuring Snapshot Settings

You can configure snapshot properties on the Setup  Compression Setup  Snapshot page.

Page 32

2MP/4MP Low Light WDR IP Camera User Guide

Snapshot Type

Set the Snapshot Type to General or Event.

General

Event

Snapshots are taken according to a user-defined schedule.

Snapshots are taken whenever an alarm, motion detection, camera tampering, or

system event occurs.

Image Size

The image size is determined by the main stream resolution setting. It is not configurable. (See Resolution on page 19).

Quality

Set the Quality to a value between 1 (lowest) and 6 (highest).

Interval

Select a snapshot frequency between 1 snapshot per second (1s) and 7 snapshots per second (7s), or click Customized to define a custom setting between 1 and 50,000 seconds.

Click Save to apply the settings.

Configuring Privacy Masks

You can configure privacy mask properties on the Setup  Compression Setup  Overlay  Privacy Masking page.

To enable privacy masking, click Enable. Four privacy masks appear in the preview window.

Page 33

You can configure the channel title properties on

preview window, and then click Save.

Configuring Video and Audio Settings

Delete any masks that you don’t need. To delete a mask, right-click it or select it and then click Delete. To remove all the masks, click Remove All.

To move a mask, select it and drag the center of the mask.

To resize a mask, drag one of the corner handles. To draw a new mask, drag your mouse anywhere in the preview window.

Click Save to apply the settings.

Configuring the Channel Title

the Setup  Compression Setup  Overlay  Channel Title page.

To display the channel title, click Enable, and then click Save. By default, the channel title appears in the lower left corner of the video image.

To move the channel title, drag the yellow Channel Title box to the desired location in the

To modify the channel title, enter the new title in the Input Channel Title field, and then click Save.

To hide the channel title, click Disable, and then click Save.

Page 34

2MP/4MP Low Light WDR IP Camera User Guide



Configuring the Time Title

You can configure the time title properties on the Setup  Compression Setup

To display the channel title, click Enable, and then click Save. By default, the channel title appears in the upper right

corner of the video image.

To display the day of the week, select the Show Day of Week check box, and then click Save.

To move the time title, drag the yellow Time Title box to the desired location in the preview window, and then click Save.

To hide the time title, click Disable, and then click Save.

Overlay  Time Title page.

Configuring Customized Text Overlays

You can configure customized text overlays on the Setup > Compression

Text Overlay page.

Setup  Overlay 

To display the text overly, click Enable, enter the desired text in the Input Text field, and then click Save. By default, the text overlay appears in the lower right corner of the video image.

Set Text Alignment to Left or Right.

To move the text overlay, drag the yellow Text Overlay box to the desired location in the preview window, and then click Save.

To hide the text overlay, click Disable, and then click Save.

Page 35



Configuring Picture Overlays

You can configure picture overlays on the

Setup

To display a picture overlay, click Enable, click Upload Picture, upload the picture, and then click Save. The file must be in BMP format, less than 16 KB, and no more than 128×128 pixels.

To move the picture overlay, drag the yellow frame to the desired location in the preview window, and then click Save.

To hide the picture overlay, click Disable, and then click Save.

Compression Setup  Overlay

Picture Overlay page.

Configuring Video and Audio Settings

Configuring Regions of Interest

You can configure regions of interest (ROI) on the Setup Compression Setup  ROI page. To enable the ROI function, click Enable.

In the preview window, drag your mouse over the portion of the scene that you want to designate as a region of interest, select an Image Quality level between 1 (lowest) and 6 (highest), and then click Save. You can add up to 4 regions of interest.

To delete a single region of interest, select it, and then click Delete. To delete all regions of interest, click Remove All.

Configuring Zoom and Focus Settings

You can configure zoom and focus on the Setup  Zoom and Focus  Zoom and Focus page.

Page 36

2MP/4MP Low Light WDR IP Camera User Guide

To adjust the zoom magnification, drag the slider right or left. Click the + and - signs to make fine adjustments. The Step number determines the magnitude of the adjustment.

To adjust the focus manually, drag the slider right or left. Click the + and - signs to make fine adjustments. The Step number determines the magnitude of the adjustment.

To set the focus automatically, click Auto Focus.

To restore the default zoom and focus settings, click Restore All.

Configuring Audio Settings

You can configure audio settings for Main Stream, Sub Stream 1, and Sub Stream 2 profiles on the Setup

 Audio Setup  Audio page.

Page 37

Configuring Video and Audio Settings

To enable audio for the stream, select the Enable check box, select the format (G.711A, G.711Mu, G.726, AAC), and then select a sampling frequency (8–64 kHz).

In the Properties area, select the audio input type (LineIn, Mic), enable or disable noise filtering, and adjust the microphone and/or speaker volumes by moving the sliders. Click the + and - signs to make fine adjustments. Click Save to apply the settings.

Page 38

2MP/4MP Low Light WDR IP Camera User Guide

5 Configuring Network Settings

This chapter contains the following sections:

• Configuring TCP/IP, page 26

• Configuring Network Connections, page 28

• Configuring ONVIF, page 29

• Configuring RSTP, page 29

• Configuring PPPoE Settings, page 30

• Configuring DDNS Settings, page 30

• Filtering IP/MAC Addresses, page 31

• Configuring Email Settings, page 33

• Configuring UPnP Port Mapping, page 34

• Configuring SNMP Settings, page 35

• Configuring Bonjour, page 36

• Configuring Multicast Settings, page 36

• Configuring 802.1X Settings, page 37

• Configuring QoS Settings, page 37

• Working with Certificates, page 38

Configuring TCP/IP

You can configure TCP/IP settings, including IPv4/IPv6 and ARP/Ping settings, on the Setup  Network Setup  TCP/IP page.

Page 39

Configuring Network Settings

IPv4 Address Configuration

By default, the camera uses IPv4 and obtains IP settings automatically via DHCP.

In the Hostname field, enter a nickname for the camera that can be mapped to the IP address and used to identify the camera.

To manually assign IP address settings, set Mode to Static, and then replace the values in the IP Address, Subnet Mask, and Default Gateway fields.

To manually assign DNS server addresses, replace the values in the Preferred DNS Server and Alternate DNS Server fields. Click Save to apply the settings.

IPv6 Address Configuration

To enable IPv6, set IP Version to IPv6. Verify that the IP address and default gateway (router) address are in the same network segment. Click Save to apply the settings.

ARP/Ping

You can assign an IP address to the camera using the ARP/Ping service.

To enable ARP/Ping to set the IP address:

1. Obtain an unused IP address in the same LAN as your PC.

2. Write down the MAC address of the camera (it is listed on the label).

3. Select the Enable ARP/Ping check box, and then click Save.

Page 40

2MP/4MP Low Light WDR IP Camera User Guide

4. Open the Command Prompt window on your PC (in Windows 7, click Start  All

Programs

for your operating system:

 Accessories  Command Prompt) and type the appropriate commands

5. Reboot the camera. If the setup was successful, the Command Prompt window will

display “Reply from" and the IP address (for example, "Reply from 192.168.0.125 …”).

To verify that the IP address works, open your browser and type in the address bar http:// followed by the IP address (for example, http://192.168.0.125), then press Enter.

Configuring Network Connections

You can configure network connections and port settings on the Setup  Network Setup  Connection

 Connection page.

Page 41

By default, the maximum number of simultaneous connections the camera will support is set to 10. To change this setting, in the Max Connections field, enter a value between 1 and 20.

If you want, you can change the TCP, UDP, HTTP, RTSP, and HTTPS port numbers from their defaults.

Click Save to apply the settings.

Configuring ONVIF

Configuring Network Settings

ONVIF (Open Network Video Interface Forum) is a global standard for the interoperability of IP-based physical security products.

You can enable or disable ONVIF authentication on the Setup  Network Setup 

Connection

ONVIF login authentication is enabled by default. To disable it, select OFF, and then click Save.

Note

 ONVIF page.

HTTPS is enabled by default. If your headend only supports ONVIF HTTP, you can disable HTTPS by clearing the HTTPS Setting check box and then clicking Save. A warning message will appear indicating that your connection is no longer secure.

Configuring RSTP

RTSP Over TLS is used to encrypt video stream transmit between browser and device or device and headend.

Page 42

2MP/4MP Low Light WDR IP Camera User Guide

Note

You can enable or disable RTSP Over TLS on the Setup RTSP page.

RTSP Over TLS is disabled by default. To enable it, click ON, and then click Save.

RTSP Over TLS is effective only for TCP protocol.

Configuring PPPoE Settings

You can configure Point-to-Point Protocol over Ethernet (PPPoE) settings on the Setup > Network Setup > PPPoE page.

 Network Setup  Connection 

To enable PPPoE:

1. Select the Enable check box.

2. In the User Name and Password fields, enter the user name and password that you

received from your Internet service provider (ISP).

3. Click Save to apply the settings. The camera will connect to the Internet via PPPoE after

rebooting.

Configuring DDNS Settings

You can configure Dynamic DNS (DDNS) settings on the Setup  Network Setup  DDNS page.

Page 43

Configuring Network Settings

You can use a DDNS service to track and update your camera’s dynamic IP address, so that even when the numeric IP address changes the DDNS address always remains the same.

To access your camera using a DDNS service:

1. Register an account with a supported DDNS service, such as DynDNS or Honeywell’s

free DDNS service (www.hennvr-ddns.com).

2. Select the Server Type check box.

3. Select your DDNS service from the Server Type drop-down list.

4. In the Domain Name field, enter the domain name (hostname) that you registered with

the DDNS service (for example, mycamera.dyndns.org).

5. In the User Name and Password fields, enter the user name and password of the

account that you registered in step 1.

6. In the Update Period field, enter the interval in minutes between address updates sent

to the DDNS server.

If you selected Honeywell DDNS as your DDNS service, the domain name is set to the camera’s MAC address by default and no user

Note

name or password are required. Set Mode to Auto or Manual. If you configure the domain name manually, click Test to verify that the domain name is registered.

7. Click Save to apply the settings. You can now access the camera by entering the

domain name in your browser’s address bar.

Filtering IP/MAC Addresses

You can configure IP filter settings on the Setup  Network Setup  IP Filter page.

Page 44

2MP/4MP Low Light WDR IP Camera User Guide

When the IP filter is enabled, remote access to the camera is restricted to specific IP or MAC addresses. You can add or remove addresses from the list at any time. If a user is accessing the camera over a WAN, enter the MAC address of the user's router instead of an IP address.

Adding IP/Mac Addresses to the List of Approved Users

To add an IP/MAC address:

1. Click Add IP/MAC.

2. In the Add IP/MAC window, select IP Address, IP Segment, or MAC from the

drop-down list, enter the relevant address, and then click Save.

The address is added to the list of approved users.

3. Select the Approved Users check box, and then click Save to apply the settings.

Editing IP/Mac Addresses

To edit an IP/MAC address:

1. In Address List, click the Modify icon of the address that you want to edit.

Page 45

2. In the Modify IP/MAC window, edit the address as needed, and then click Save.

Configuring Network Settings

Deleting IP/Mac Addresses from the List of Approved Users

To delete a single IP/MAC address:

1. In the Address List, click the Delete icon of the address that you want to delete.

2. A confirmation message appears. Click OK to continue, and then click Save to apply the

settings. The address is removed from the list of approved users.

To delete multiple IP/MAC addresses:

1. Click Remove All.

2. A confirmation message appears. Click OK to continue, and then click Save to apply the

settings. All addresses are removed from the list of approved users.

Configuring Email Settings

You can configure email notification settings on the Setup  Network Setup SMTP page.

To set up email notifications:

1. In the SMTP Server and Port fields, enter the SMTP server and port information.

2. In the User Name and Password fields, enter the sender’s email user name and

password. Alternatively, if the server supports anonymous login, you can select the

Page 46

2MP/4MP Low Light WDR IP Camera User Guide

Anonymous check box to log in without a user name and password.

3. In the Sender field, enter the sender’s email address.

4. From the Authentication list, select an encryption mode (SSL or TLS) or select None.

5. In the Title field, enter the text that you want to appear in the subject line of the email.

6. Select the Attachment check box if you want to enable snapshot attachments.

7. In the Mail Receiver field, enter the recipient’s email address, and then click the + sign

to add it to the list. You can enter up to three email addresses. To remove an address from the list, select it, and then click the – sign.

8. In the Interval field, specify the interval between email notification messages. Enter a

value between 0 (no interval) and 3600 seconds (60 minutes).

Setting an interval between email notifications reduces the load on

Note

the email server if multiple notifications are triggered simultaneously.

9. To have the system periodically verify that the email notification settings are working,

select the Send Health Messages check box, and specify the Interval.

10. Click Save to apply the settings.

11. Click Email Test to send a test email to verify that the settings are configured properly.

Configuring UPnP Port Mapping

You can configure Universal Plug and Play (UPnP) settings on the Setup  Network Setup  UPnP page.

The UPnP protocol is used to detect network devices with clients running Windows.

To enable UPnP, select the Enable check box. The camera can now be detected by Windows' built-in network browser (My Network Places in Windows XP; Network in Windows 7).

To enable UPnP in Windows XP:

1. Go to Start > Control Panel > Add or remove programs.

2. Click Add or remove programs, then select Networking Services in the Windows

Page 47

Components Wizard.

3. Click Details, then select Internet Gateway Device Discovery and Control Client and

UPnP User Interface.

4. Click OK to begin the installation.

To enable UPnP in Windows 7:

1. Go to Start > Control Panel > Network and Internet > Network and Sharing Center.

2. On the left pane, click Change advanced sharing settings.

3. On your current network profile, in the Network discovery area, click Turn on network

discovery, and then click Save changes.

Configuring SNMP Settings

You can configure Simple Network Management Protocol (SNMP) settings on the Setup  Network Setup

 SNMP page.

Configuring Network Settings

SNMP is a protocol for collecting, organizing, and exchanging management information between managed devices on a network.

To enable SNMP:

1. Next to SNMP Version, select the SNMP version(s) that you want to use. For best

security, use SNMPv3. You can select SNMPv1 only, SNMPv2 only, both SNMPv1 and SNMPv2, or SNMPv3 only.

Note If you select SNMPv1 or SNMPv2, a warning message will appear.

2. By default, the SNMP Port is 161. To change the port, enter a number in the range

1–65535.

3. In the Trap Address field, enter the IP address of the SNMP server where trap

notifications will be sent.

4. By default, the Trap Port is 162. To change the port, enter a number in the range

1–65535.

Page 48

2MP/4MP Low Light WDR IP Camera User Guide

5. If SNMPv3 is selected, for both read-only and read-write, enter a user name, select an

authentication method (MD5 or SHA), and create authentication and encryption passwords (must be at least 8 characters long).

6. Click Save to apply the settings.

Configuring Bonjour

You can configure Bonjour settings on the Setup  Network Setup  Bonjour page.

Bonjour is a zero configuration networking application that allows you to create a network in which devices can discover each other without requiring any user configuration.

When this function is enabled, you can discover the camera on a Mac OS computer by opening Safari and going to Display All Bookmarks > Bonjour.

Bonjour is enabled by default. To disable it, clear the Enable check box, and then click Save.

Configuring Multicast Settings

You can configure multicast settings on the Setup  Network Setup  Multicast page.

Multicast is a transmission mode for data packets that minimizes bandwidth use and CPU load when multiple computers are receiving the same data packet simultaneously. You can configure multicast for Main Stream, Sub Stream 1, and Sub Stream 2 profiles.

To enable multicast:

1. For each stream that you want to enable multicast in, select the Enable check box, and

then enter a multicast address and port, using the suggested ranges as a guide.

2. Click Save to apply the settings.

To view video in multicast mode:

• In Live view, select Multicast from the Protocol drop-down list.

Page 49

Configuring 802.1X Settings

You can configure 802.1X settings on the Setup  Network Setup  802.1X page.

802.1X is a port-based network access control protocol for preventing unauthorized devices

from accessing the LAN. You can set up user name and password credentials for the camera so that it is not blocked by the network switch.

To enable 802.1X:

1. Select the Enable check box.

2. In the User Name field, enter the user name that will be used to authenticate the camera.

3. In the Password field, enter the password that will be used to authenticate the camera.

Configuring Network Settings

4. Click Save to apply the settings.

Configuring QoS Settings

You can configure Quality of Service (QoS) settings on the Setup  Network Setup  QoS page.

QoS settings control bandwidth use by prioritizing certain data packets over others.

To enable QoS:

1. In the Realtime Monitor field, enter a DSCP (Differentiated Services Codepoint) value for

live video packets. Select a value between 0 (lowest priority) and 63 (highest priority).

2. In the Command field, enter a DSCP (Differentiated Services Codepoint) value for non-

video packets. Select a value between 0 (lowest priority) and 63 (highest priority).

3. Click Save to apply the settings.

Page 50

2MP/4MP Low Light WDR IP Camera User Guide

Working with Certificates

Importing Certificates

You can configure certificate settings on the Setup  Network Setup  Certificate page.

To install a Honeywell-signed root certificate:

1. Click Export, navigate to the directory where you want to save the certificate (ca.crt)

on your PC, and then click Save.

2. Go to the directory where you saved the certificate and double-click the certificate.

The Certificate window opens.

3. In the Certificate window, on the General tab, click Install Certificate to open the

Certificate Import Wizard.

4. Click Next to continue.

5. Click Place all certificates in the following store, click Browse, click Trusted Root

Certification Authorities, and then click OK.

6. Click Next, and then click Finish to close the Certificate Import Wizard. A confirmation

dialog box appears with the message “The import was successful.”

7. Click OK, and then click OK to close the Certificate window.

To import certificate from 3

1. Select a certificate type from the Type drop-down list.

2. In the File field, click Browse to select a certificate file you have already applied from 3rd

party:

party or CA domain.

3. In the Key field, click Browse to select a certificate key you have already applied from 3rd

party or CA domain.

4. Click Import button and reboot camera.

Supported certificate type: HTTPS protocol.

Note

Supported certificate file and Key: PEM format.

Page 51

Certificate Request

You can fill in certificate information and the certificate request file can be exported to the certificate issuing authority for signing and then being imported to camera.

1. Navigate to Setup  Network Setup  Certificate Request page.

2. Enter the required information and then click Export.

Configuring Network Settings

Page 52

2MP/4MP Low Light WDR IP Camera User Guide

6 Configuring Event Settings

This chapter contains the following sections:

• Configuring Alarm Events, page 40

• Configuring System Events, page 42

• Configuring Motion Detection Events, page 44

• Configuring Camera Tampering Events, page 46

• Configuring Scene Change Events, page 47

• Configuring Audio Events, page 48

• Configuring Smart Plan, page 49

• Configuring IVS Analysis Events, page 50

• Configuring Face Detection Events, page 51

• Configuring People Counting Events, page 52

• Configuring Heat Map Events, page 54

Configuring Alarm Events

You can configure alarm event settings on the Setup  Alarm Setup  Alarm Setup page.

To enable the alarm function:

1. Select the Enable check box.

2. From the Alarm Input list, select the alarm input that you want to configure (Alarm1 or

Alarm2).

3. Next to Alarm Period, click Setup. The Alarm Period window opens.

Page 53



Configuring Event Settings

4. Set the days and times when you want the alarm function to be active, and then click Save.

5. In the Anti-Dither field, enter the anti-dither time in seconds. Enter a value between 0

and 100 seconds. The system will only allow one alarm event within this period.

6. Set Sensor Type to NO (normally open) or NC (normally closed), depending on the

alarm input type.

7. To start recording video when an alarm event is detected, select the Record check box.

8. In the Record Delay field, enter the number of seconds that the system will continue to

record video after an alarm event has ended. Enter a value between 10 and 300.

9. To generate an alarm output when an alarm event is detected, select the Alarm Output

check box and select the alarm output(s) to be activated.

10. In the Alarm Delay field, enter the number of seconds that the system will continue to

generate an alarm output after an alarm event has ended. Enter a value between 10 and

300.

11. To send an email notification when an alarm event is detected, select the Send Email

check box. Email settings must be configured in Setup (Email). See

12. To take a snapshot when an alarm event is detected, select the Snapshot check box.

Configuring Email Settings on page 33.

 Network Setup  SMTP

For the snapshot to be attached to the email notification, the

Note

Attachment check box must be selected in Setup

Network Setup

SMTP (Email). See Configuring Email Settings on page 33.

13. Click Save to apply the settings.

Page 54

2MP/4MP Low Light WDR IP Camera User Guide

Configuring System Events

You can configure system event settings (for SD card and network errors and illegal login attempts) on the Setup

 Alarm Setup  Event page.

Configuring SD Card Event Settings

There are three types of SD card events:

• No SD Card: There is no microSD card installed in the camera.

• SD Card Error: The installed microSD card is not working.

• Capacity Warning: The installed microSD card is full.

You can configure settings for each type of event.

To enable SD card event detection:

1. On the SD Card tab, select the event type that you want to configure from the Event

Type list (No SD Card, SD Card Error, or Capacity Warning).

2. Select the Enable check box.

3. To generate an alarm output when an event is detected, select the Alarm Output check

box and select the alarm output(s) to be activated.

4. In the Alarm Delay field, enter the number of seconds that the system will continue to

generate an alarm output after the event has ended. Enter a value between 10 and 300.

5. To send an email notification when the event is detected, select the Send Email check

box. Email settings must be configured in Setup

Configuring Email Settings on page 33.

6. Click Save to apply the settings.

Configuring Network Event Settings

There are two types of network events:

• Network Disconnected: The camera is offline.

• IP Conflict: The camera has the same IP address as another device on the network.

You can configure settings for each type of event.

 Network Setup  SMTP (Email). See

Page 55

Configuring Event Settings

To enable network event detection:

1. On the Network tab, select the event type that you want to configure from the Event

Type list (Network Disconnected or IP Conflict).

2. Select the Enable check box.

3. In the IP Address field, enter the IP address of the headend, and in the Time field, enter

the countdown time. If no connection is established with the IP address within the specified time, the system will will detect a network disconnection event.

4. To start recording video when the event is detected, select the Record check box.

5. In the Record Delay field, enter the number of seconds that the system will continue to

record video after the event has ended. Enter a value between 10 and 300.

6. To generate an alarm output when an event is detected, select the Alarm Output check

box and select the alarm output(s) to be activated.

7. In the Alarm Delay field, enter the number of seconds that the system will continue to

generate an alarm output after the event has ended. Enter a value between 10 and 300.

8. Click Save to apply the settings.

Configuring Illegal Access Event Settings

An illegal access event occurs when a specified number of unsuccessful login attempts is exceeded.

To enable illegal access detection:

1. On the Illegal Access tab, select the Enable check box.

Page 56

2MP/4MP Low Light WDR IP Camera User Guide

2. In the Failed Login Attempts field, enter the number of unsuccessful login attempts the

system will allow before an illegal access event is detected. Enter a value between 3 and

10.

3. To generate an alarm output when an event is detected, select the Alarm Output check

box and select the alarm output(s) to be activated.

4. In the Alarm Delay field, enter the number of seconds that the system will continue to

generate an alarm output after the event has ended. Enter a value between 10 and 300.

5. To send an email notification when an illegal access event is detected, select the Send

Email check box. Email settings must be configured in Setup (Email), See

Configuring Email Settings on page 33.

Configuring Motion Detection Events

You can configure motion detection event settings on the Setup  Onboard Video Analytics  Video Detection  Motion Detection page.

 Network Setup  SMTP

To enable motion detection:

1. Select the Enable check box.

2. Next to Alarm Period, click Setup. The Alarm Period window opens.

3. Set the days and times when you want the alarm function to be active, and then click Save.

4. In the Anti-Dither field, enter the anti-dither time in seconds. Enter a value between 0

and 100 seconds. The system will only allow one motion detection event within this period.

5. Set up motion detection areas:

a. Next to Area, click Setup. The Area window opens.

Page 57

Configuring Event Settings

b. By default, the whole video window is configured as a motion detection area. To define

a smaller area, drag your mouse over the area(s) that you want to deselect, or click Remove All, and then redraw the area(s) with your mouse.

c. You can define up to 4 motion detection profiles (regions), each with different

sensitivity and threshold settings. Next to Region, click one of the solid color tiles to select a region. Drag the Sensitivity and Threshold sliders to the desired values. Click the – and + signs to make fine adjustments.

Sensitivity measures the amount of change in a scene that qualifies as motion. Threshold measures the amount of motion in a scene required to trigger a motion detection event.

d. Click Save to apply the settings.

6. To start recording video when motion is detected, ensure that the Record check box is

selected.

7. In the Record Delay field, enter the number of seconds that the system will continue to

record video after the event has ended. Enter a value between 10 and 300.

8. To generate an alarm output when motion is detected, select the Alarm Output check

box

and select the alarm output(s) to be activated.

9. In the Alarm Delay field, enter the number of seconds that the system will continue to

Page 58

2MP/4MP Low Light WDR IP Camera User Guide

generate an alarm output after the event has ended. Enter a value between 10 and 300.

10. To send an email notification when motion is detected, select the Send Email check box.

Email settings must be configured in Setup

 Network Setup  SMTP (Email). See

Configuring Email Settings on page 33.

11. To take a snapshot when motion is detected, select the Snapshot check box.

For the snapshot to be attached to the email notification, the

Note

Attachment check box must be selected in Setup > Network Setup > SMTP (Email). See Configuring Email Settings on page 33.

12. Click Save to apply the settings.

Configuring Camera Tampering Events

You can configure camera tampering event settings on the Setup  Onboard Video Analytics  Video Detection  Video Tampering page.

To enable camera tampering detection:

1. Select the Enable Tamper Detect and/or the Enable Defocus Detect check box(es).

2. Next to Alarm Period, click Setup. The Alarm Period window opens.

3. Set the days and times when you want the alarm function to be active, and then click Save.

4. To start recording video when a tampering event is detected, ensure that the Record check

box is selected.

5. In the Record Delay field, enter the number of seconds that the system will continue to

record video after a tampering event has ended. Enter a value between 10 and 300.

6. To generate an alarm output when a tampering event is detected, select the Alarm

Output check box and select the alarm output(s) to be activated.

7. In the Alarm Delay field, enter the number of seconds that the system will continue to

generate an alarm output after a tampering event has ended. Enter a value between 10 and 300.

8. To send an email notification when a tampering event is detected, select the Send Email

Page 59



check box. Email settings must be configured in Setup  Network Setup  SMTP (Email). See

9. To take a snapshot when a tampering event is detected, select the Snapshot check box.

Configuring Email Settings on page 33.

For the snapshot to be attached to the email notification, the

Note

Attachment check box must be selected in Setup

SMTP (Email). See Configuring Email Settings on page 33.

10. Click Save to apply the settings.

Configuring Scene Change Events

You can configure scene change event settings on the Setup  Onboard Video Analytics  Video Detection

 Scene Change page.

Configuring Event Settings

Network Setup

To enable scene change detection:

1. Select the Enable check box.

2. Next to Alarm Period, click Setup. The Alarm Period window opens.

3. Set the days and times when you want the alarm function to be active, and then click Save.

4. To start recording video when a scene change event is detected, select the Record

check box.

5. In the Record Delay field, enter the number of seconds that the system will continue to

record video after a scene change event has ended. Enter a value between 10 and 300.

6. To generate an alarm output when a scene change event is detected, select the Alarm

Output check box and select the alarm output(s) to be activated.

7. In the Alarm Delay field, enter the number of seconds that the system will continue to

generate an alarm output after a scene change event has ended. Enter a value between 10 and 300.

8. To send an email notification when an alarm event is detected, select the Send Email

check box. Email settings must be configured in Setup (Email). See

Configuring Email Settings on page 33.

 Network Setup  SMTP

Page 60

2MP/4MP Low Light WDR IP Camera User Guide



9. To take a snapshot when an alarm event is detected, ensure that the Snapshot check

box is selected.

For the snapshot to be attached to the email notification, the

Note

10. Click Save to apply the settings.

Attachment check box must be selected in Setup

SMTP (Email). See Configuring Email Settings on page 33.

Configuring Audio Events

You can configure audio event settings on the Setup  Onboard Video Analytics  Audio Detection page.

Network Setup

To enable audio event detection:

1. To detect faults in the audio input, select the Enable Input Abnormality check box.

2. To detect unusual changes in the audio input:

a. Select the Enable Intensity Change check box.

b. Drag the Sensitivity and Threshold sliders to the desired values. Click the – and +

signs to make fine adjustments. Sensitivity controls changes to the audio input volume. Threshold controls the amount of change allowed in the audio environment before an audio detection event is triggered.

Page 61



3. Next to Alarm Period, click Setup. The Alarm Period window opens.

4. Set the days and times when you want the alarm function to be active, and then click Save.

5. In the Anti-Dither field, enter the anti-dither time in seconds. Enter a value between 0 and

Configuring Event Settings

100 seconds. The system will only allow one audio event within this period.

6. To start recording video when an audio event is detected, ensure that the Record check

box is selected.

7. In the Record Delay field, enter the number of seconds that the system will continue to

record video after an audio event has ended. Enter a value between 10 and 300.

8. To generate an alarm output when an audio event is detected, select the Alarm Output

check box and select the alarm output(s) to be activated.

9. In the Alarm Delay field, enter the number of seconds that the system will continue to

generate an alarm output after an audio event has ended. Enter a value between 10 and

300.

10. To send an email notification when an audio event is detected, select the Send Email

check box. Email settings must be configured in Setup (Email). See

11. To take a snapshot when an audio event is detected, select the Snapshot check box.

Configuring Email Settings on page 33.

 Network Setup  SMTP

For the snapshot to be attached to the email notification, the

Note

Attachment check box must be selected in Setup

SMTP (Email). See Configuring Email Settings on page 33.

12. Click Save to apply the settings.

Configuring Smart Plan

Smart plan is a master switch for the intelligent analytics such as “Face Detection”, “Heat Map”, “IVS” and “People Counting” etc. The device intelligent functions can be valid after smart plan is enabled.

You can configure smart plan on the Setup  Event  Smart Plan page. Select the plan by clicking its icon and click Save.

Network Setup

Page 62

2MP/4MP Low Light WDR IP Camera User Guide

Configuring IVS Analysis Events

You can configure IVS analysis event settings on the Setup  Onboard Video Analytics  IVS Analysis page.

To enable IVS Analysis:

Select the check box of rules to be applied and set the rule type.

Click Draw Rule to set up an area for people counting. You can move or resize the area using the

Click Draw Target to set up the target size. You can move or resize the area using your mouse. To move the area, drag one of the sides. To resize the area, drag one of the

your mouse. To move the area, drag one of the sides. To resize the area, drag one of

corner handles.

corner

handles.

Next to Alarm Period, click Setup. The Alarm Period window opens.

Set the days and times when you want the alarm function to be active, and then click Save.

In the Duration field, enter the number of seconds of duration. Enter a value between 6 and 3600

To start recording video when an event is detected, select the Record check box.

In the Record Delay field, enter the number of seconds that the system will continue to record video after the event has ended. Enter a value between 10 and 300.

To generate an alarm output when an event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

10.

In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after the event has ended. Enter a value between 10 and 300.

11.

To send an email notification when an event is detected, select the Send Email check box. Email settings must be configured in Setup  Network Setup  SMTP (Email). See

Configuring Email Settings on page 33.

12.

To take a snapshot when an event is detected, select the Snapshot check box.

Page 63



For the snapshot to be attached to the email notification, the

Note

Attachment check box must be selected in Setup

SMTP (Email). See Configuring Email Settings on page 33.

13.

Click Save to apply the settings.

Configuring Face Detection Events

You can configure face detection event settings on the Setup  Onboard Video Analytics  Face Detection page.

Configuring Event Settings

Network Setup

To enable face detection:

Select the Enable check box.

Click Draw Target to set up the face detection area. You can move or resize the area using your mouse. To move the area, drag one of the sides. To resize the area, drag one of the corner handles.

Next to Alarm Period, click Setup. The Alarm Period window opens.

Set the days and times when you want the alarm function to be active, and then click Save.

To enable face enhancement, select the Enable Face Enhancement check box.

To start recording video when an event is detected, select the Record check box.

In the Record Delay field, enter the number of seconds that the system will continue to record video after the event has ended. Enter a value between 10 and 300.

To generate an alarm output when an event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after the event has ended. Enter a value between 10 and 300.

Page 64

2MP/4MP Low Light WDR IP Camera User Guide



10.

To send an email notification when an event is detected, select the Send Email check box. Email settings must be configured in Setup  Network Setup  SMTP (Email). See

Configuring Email Settings on page 33.

11.

To take a snapshot when an event is detected, select the Snapshot check box.

For the snapshot to be attached to the email notification, the

Note

12.

Click Save to apply the settings.

Attachment check box must be selected in Setup

SMTP (Email). See Configuring Email Settings on page 33.

Configuring People Counting Events

People Counting

Network Setup

You can configure IVS analysis event settings on the People Counting tab of the Setup  Onboard Video Analytics

To enable people counting:

 People Counting page.

Select the Enable check box.

Click Draw Rule to set up an area for people counting. You can move or resize the area using

your mouse. To move the area, drag one of the sides. To resize the area, drag one of

Page 65



corner handles.

the

Click Draw Target to set up the target size. You can move or resize the area using your mouse. To move the area, drag one of the sides. To resize the area, drag one of the

Configuring Event Settings

corner

handles.

To enable OSD which displays the Enter and Leave numbers, select the Enable OSD check box. To restore the numbers, click Clear.

Next to Alarm Period, click Setup. The Alarm Period window opens.

Set the days and times when you want the alarm function to be active, and then click Save.

In the Rule Name field, enter the name of rule.

In the Direction field, select the direction of people counting. You can select A->B or B->A, the arrow direction always means the entrance direction.

In the People Counting Alarm field, set the enter number, leave number, stranded number. It will trigger alarm when it exceeds the limited stranded number.

10.

To start recording video when an event is detected, select the Record check box.

11.

In the Record Delay field, enter the number of seconds that the system will continue to record video after the event has ended. Enter a value between 10 and 300.

12.

To generate an alarm output when an event is detected, select the Alarm Output check box and select the alarm output(s) to be activated.

13.

In the Alarm Delay field, enter the number of seconds that the system will continue to generate an alarm output after the event has ended. Enter a value between 10 and 300.

14.

To send an email notification when an event is detected, select the Send Email check box. Email settings must be configured in Setup  Network Setup  SMTP (Email). See

Configuring Email Settings on page 33.

15.

To take a snapshot when an event is detected, select the Snapshot check box.

16.

Report

You can run and export report of people counting on the Report tab of the Setup  Onboard Video Analytics

For the snapshot to be attached to the email notification, the

Note

Attachment check box must be selected in Setup

SMTP (Email). See Configuring Email Settings on page 33.

Click Save to apply the settings.

 People Counting page.

Network Setup

Page 66

2MP/4MP Low Light WDR IP Camera User Guide

To run a report, select the report type and set the criteria as needed. Click Search and the report will be displayed.

To export the report, click Export.

Configuring Heat Map Events

You can configure IVS analysis event settings on the Setup  Onboard Video Analytics  Heat Map page.

To enable heat map:

Select the Enable check box.

Next to Alarm Period, click Setup. The Alarm Period window opens. Set the days and times when you want the alarm function to be active, and then click Save.

Click Save to apply the settings.

Page 67

Intelligent Analytics System

7 Intelligent Analytics System

You can access the Intelligent Analytics System from the Setup  Intelligent Analytics

System page. Click to go to INTELLIGENT ANALYTICS SYSTEM webpage.

Page 68

2MP/4MP Low Light WDR IP Camera User Guide

8 Configuring Recording Settings

This chapter contains the following sections:

• Configuring Recording Schedules, page 56

• Configuring Storage Settings, page 57

• Configuring Recording Settings, page 59

Configuring Recording Schedules

You can set up both regular and holiday schedules for recording video and saving snapshots on the Setup

 Storage Setup  Schedule page.

On the Record Schedule tab, click the Setup buttons to configure weekend, weekday, and holiday settings, for general video recording as well as motion detection and alarm recording.

You can configure up to 6 different recording periods per day. Click Save to apply the settings.

Follow the same procedure to configure the settings on the Snapshot Schedule tab.

On the Holiday Schedule tab, you can designate holidays by clicking dates on the calendar.

Page 69

On the selected dates, the video recording/snapshot schedule will follow the holiday settings you configured in the Record Schedule and Snapshot Schedule tabs. Click Save to apply the settings.

Configuring Storage Settings

Configuring Recording Settings

You can configure recording storage settings on the Setup  Storage Setup  Destination page.

Configuring Storage Paths

On the Path tab, you can specify where you want recorded video and snapshots—whether scheduled or triggered by a motion detection or alarm event—to be saved: to a local SD card, to an FTP server, or to an NAS disk.

Select which recorded events you want to save and where you want to save them, then click

Save to apply the settings.

Note

Only one network storage option can be used at a time. FTP and NAS cannot be used together.

Page 70

2MP/4MP Low Light WDR IP Camera User Guide

Configuring the Local SD Card for Storage

If the camera has a microSD card installed, the Local tab displays the microSD card details.

You can set up the installed microSD card for read-only, read-and-write, or hot swap operation by clicking the corresponding button.

• Read Only: Data on card can be displayed but not modified.

• Read & Write: Data on card can be displayed and modified.

• Hot Swap: Card can be inserted or removed without turning off the camera.

If you want to erase all of the data on the microSD card, click Format. A confirmation message appears. Click OK to continue. The card is formatted and the camera reboots.

Configuring an FTP Server for Storage

On the FTP tab, you can enable FTP storage and configure storage settings.

To enable FTP storage:

1. Select the Enable check box.

2. In the Server Address and Port fields, enter the address and port number of the FTP

server.

3. In the User Name and Password fields, enter the user name and password of the server.

4. In the Remote Directory field, enter the directory on the server where the recorded

video/snapshot files will be stored.

5. Click Save to apply the settings.

Page 71

Configuring Recording Settings

Panic Save

To save recorded video/snapshots to the camera's microSD card when the network connection to the FTP is offline or unavailable, select the Panic Save (Local) check box, and then click Save to apply the setting.

Configuring an NAS Disk for Storage

On the NAS tab, you can enable network attached storage and configure storage settings.

To enable network attached (NAS) storage:

1. Select the Enable check box.

2. In the Server Address field, enter the address of the NAS server.

3. In the Remote Directory field, enter the directory on the server where the recorded

video/snapshot files will be stored.

4. Click Save to apply the settings.

Configuring Recording Settings

You can configure recording settings on the Setup  Storage Setup  Record Control page.

By default, recorded video files are 8 minutes or 30 minutes long (depending on your camera model). To change this setting, enter a time between 1 and 120 minutes in the Record Length field.

By default, the pre-event record time (the number of seconds the system stores in a buffer) is 5 seconds. To change this setting, enter a time between 0 and 5 seconds in the Pre-Event Record field.

In the Auto-Delete Old Files field, set the number of days to delete video files automatically.

From the Disk Full list, select Overwrite or Stop.

Page 72

2MP/4MP Low Light WDR IP Camera User Guide

• Overwrite: Recording continues when disk capacity is reached and overwrites

previously saved video.

• Stop: Recording stops when disk capacity is reached. Nothing is overwritten and no

further video is recorded.

Set Record Mode to Auto, Manual, or Off.

• Auto: Video records continuously.

• Manual: Video recording must be initiated by user.

• Off: Video recording is disabled.

From the Record Stream list, select the stream profile that you want to use for recording video: Main Stream or Sub Stream.

Click Save to apply the settings.

Page 73

Configuring System Settings

9 Configuring System Settings

This chapter contains the following sections:

• Configuring General System Settings, page 61

• Configuring Date and Time Settings, page 61

• Configuring Account Settings, page 63

• Resetting the Camera, page 67

• Backing Up/Restoring a Configuration, page 68

• Configuring Maintenance Settings, page 68

• Upgrading the Firmware, page 69

• Viewing Version Information, page 69

• Managing Logs, page 70

• Viewing Online Users, page 71

Configuring General System Settings

You can configure the device name, user interface language, video standard, analog output, and status LED settings on the Setup

To change the device name, in the Device Name field, enter a new name, and then click Save.

To change the interface language, select a language from the change the video standard, select NTSC or PAL from the Video Standard list, and then click Save.

To change the analog output, select ON or OFF from the Analog Output list, and then click Save. To change the Max Log Quantity, enter a value between 1 and 1024, and then click Save.

 System Setup  General page.

Language

list, and then click

Save. To

Configuring Date and Time Settings

You can configure the date and time settings on the Setup  System Setup  Date & Time page.

Page 74

2MP/4MP Low Light WDR IP Camera User Guide

Changing the Date and Time Format

You can change the format of the date and time that appear in the text overlay on the video. To change the date format, select one of the following formats from the Date Format list: Year-Month-Day, Month-Day-Year, or Day-Month-Year. Click Save to apply the settings.

To change the time format, select 24_Hour_Standard or 12_Hour_Standard from the Time Format list.

Setting the Date and Time

There are three ways you can set the camera’s date and time. You can manually enter the date and time, synchronize with your PC’s internal clock, or set up the camera to synchronize automatically with a Network Time Protocol (NTP) server at regular intervals.

To manually set the date and time, enter the date and time in the Current Time fields, and then click Save.

To synchronize the date and time with your PC, click Sync PC. If the synchronization is successful, the message “Save succeeded” appears. You must manually click Sync PC each time you want the date and time to synchronize with the PC.

To synchronize the time with an NTP server:

1. From the Time Zone list, select your time zone.

2. If you are in an area that observes Daylight Saving Time (DST):

a. Select the Enable DST check box.

b. Set DST Type to Week.

c. Set Start Time to Mar 2nd Sunday 02:00:00 AM.

d. Set End Time to Nov 1st Sunday 02:00:00 AM.

3. Select the Synchronize with NTP check box.

4. If you want, you can change the NTP Server from the default (time-a.nist.gov).

Page 75

5. In Update Period field, enter the interval at which you want the camera’s date and time

to synchronize with the NTP server. You can enter a value between 0 and 30.

6. Click Save to apply the settings.

Configuring Account Settings

You can manage user accounts and permissions on the Setup  System Setup  Account page.

Configuring System Settings

Managing Groups

By default, there are two categories or “groups” of users: admin and user. If you want, you can create additional custom groups.

Creating a Group

You can create a new custom group and assign permissions to it.

To create a group:

1. On the Group tab, click Add Group to open the Add Group window.

2. Enter a name for the group in the Group field.

Page 76

2MP/4MP Low Light WDR IP Camera User Guide

Name

Description

Live interface.

controls in the Playback interface.

Record Control.

interface.

Account.

Alarm.

Log Search

The user can search logs in Setup  Information  Log.

Clear Log

The user can clear logs in Setup  Information  Log.

Upgrade.

Auto Maintain.

General.

Setup  Video and in Setup  Audio Setup.

Schedule and in Setup  Storage Setup  Destination.

Network

The user can access the settings in Setup  Network Setup.

Event.

Video Detect.

Default.

Properties.

IVS

The user can access the settings in Setup  Video Analytics.

3. If you want, you can enter a brief description in the Remark field.

4. From the Authority List, select permissions for the group.

Table 9-1 Permissions

Live The user can view live video and access all of the controls in the

Playback The user can play back recorded video and access all of the

Record Control The user can access the settings in Setup  Storage Setup 

Backup The user can save and export video clips in the Playback

User Management The user can access the settings in Setup  System Setup 

Alarm The user can access the settings in Setup  Alarm Setup 

Upgrade The user can upgrade firmware in Setup  System Setup 

Auto Maintain The user can access the settings in Setup  System Setup 

General The user can access the settings in Setup  System Setup 

Video/Audio The user can access the settings in Setup  Compression

Schedule/Destination The user can access the settings in Setup  Storage Setup >

Event The user can access the settings in Setup  Alarm Setup >

Video Detection The user can access the settings in Setup  Video Analytics 

Restore Defaults The user can access the settings in Setup  System Setup 

Camera Properties The user can access the settings in Setup  Camera Setup 

5. Click Save to apply the settings. The group is added to the list.

Modifying a Group

You can modify the permissions of the administrator group, user group, and any custom groups that you have created.

To modify a group:

1. On the Group tab, select the group that you want to modify (your selection will be

Page 77

Configuring System Settings

highlighted yellow), and then click the Modify icon to open the Modify Group window.

2. If you want, you can edit the description in the Remark field.

3. From the Authority List, select or deselect specific permissions for the group (see

Table 9-1), or select the All check box to select/deselect all of the permissions.

4. Click Save to apply the settings.

Deleting a Group

You can delete any custom group that you have created (you cannot delete the administrator group or the user group).

To delete a group:

1. On the Group tab, select the group that you want to delete (your selection will be

highlighted yellow), and then click the Delete icon .

2. A confirmation message appears. Click OK to continue. The group is removed from

the list.

Managing Users

You can create, modify, or delete a user account.

Creating a User Account

You can create a new user account and assign permissions to it.

To create a user account:

1. On the User Name tab, click Add User to open the Add User window.

Page 78

2MP/4MP Low Light WDR IP Camera User Guide

page 64.

2. Assign the account a user name and password.

a. In the User Name field, enter a unique user name.

b. In the Password field, enter a password. The password must be at least 8

characters in length and contain a combination of uppercase and lowercase letters, at least one number, and at least one special character.

3. Assign the account to a group (admin, user, or a custom group that you have created)

chosen from the Group list.

4. If you want, you can enter a brief description in the Remark field.

5. From the Authority List, select permissions for the account (see Table 9-1).

Each user is assigned to a group. The individual user’s permissions

Note

cannot exceed those of the group to which the user belongs. To modify permissions at the group level, see Modifying a Group

6. Click Save to apply the settings. The user account is added to the list.

Modifying a User Account

You can modify the user name, password, and permissions of a user account.

To modify a user account:

1. On the User Name tab, select the user account that you want to modify (your selection

will be highlighted yellow), and then click the Modify icon to open the Modify User window.

Page 79

page 64..

Configuring System Settings

2. To change the password, select the Modify Password check box, enter the Old

Password and the New Password in the corresponding fields, and then re-enter the new password in the Confirm Password field.

3. To change the group, select a group from the Group list.

4. If you want, you can edit the description in the Remark field.

5. From the Authority List, select or deselect specific permissions for the account (see Table

8-1), or select All to select/deselect all of the available permissions.

Each user is assigned to a group. The individual user’s permissions

Note

cannot exceed those of the group to which the user belongs. To modify permissions at the group level, see Modifying a Group

6. Click Save to apply the settings.

Deleting a User Account

You can delete any user account that you have created (you cannot delete the admin user).

To delete a user account:

1. On the User Name tab, select the user account that you want to delete (your selection

will be highlighted yellow), and then click the Delete icon .

2. A confirmation message appears. Click OK to continue. The user account is removed

from the list.

Resetting the Camera

You can reset the camera to its factory default settings on the Setup  System Setup  Default page.

Page 80

2MP/4MP Low Light WDR IP Camera User Guide

To reset the camera, click:

• Default – Recover configurations to default except network IP address and user

management.

• Factory Default – Completely recover device parameters to factory default.

A confirmation message appears. Click OK to continue. The camera reboots automatically and reverts to its factory default settings.

Backing Up/Restoring a Configuration

You can back up or restore configuration settings on the Setup > System Setup > Import/Export page.

To back up a configuration:

1. Click Export. The Input Key window pops up and enter a key for encryption.

2. The Save As window opens. By default, the backup file is named DeviceConfig.backup.

Rename the file if you want, navigate to the directory where you want to save the file, and then click Save. The file path is displayed under Backup Path.

To restore a saved configuration:

1. Click Import. The Input Key window pops up and enter the key for decryption.

2. The directory displayed under Backup Path opens in a new window.

3. Click the backup file (for example, DeviceConfig.backup). The configuration settings

are applied immediately.

Configuring Maintenance Settings

Two automatic maintenance functions are available on the Setup  System Setup  Auto Maintain page. You can set up the camera to reboot daily or weekly and delete old files

automatically.

Page 81

To enable the auto reboot function, select the Auto Reboot check box, and then specify the reboot schedule (for example, every Tuesday at 2 a.m.). Click Save to apply the settings.

To enable the auto delete function, select the Auto Delete Old Files check box, and then specify the age (in days) of the files to be deleted. For example, if you enter 30, files that are 30 days old and older will be deleted automatically. Click Save to apply the settings.

Upgrading the Firmware

You can upgrade the camera firmware on the Setup  System Setup  Upgrade page.

Configuring System Settings

Note

To upgrade the firmware:

1. Click Import.

2. Navigate to the location of the firmware file (.bin), select it, and then click Open. The file

name appears in the Firmware File field.

3. Click Upgrade to install the firmware.

4. Reboot the camera.

Note

Before you begin, you will need to obtain the new firmware and save it to your PC or to an external drive.

If you attempt to install an older version of the firmware, a warning message will appear.

Viewing Version Information

You can view the camera’s firmware version, web client version, ONVIF version, and serial number on the Setup

 Information  Version page.

Page 82

2MP/4MP Low Light WDR IP Camera User Guide

Managing Logs

You can view, back up, and delete log files on the Setup  Information  Log page.

Viewing Logs

There are seven log types: System, Setting, Data, Event, Record, Account, and Clear Log.

To view logs by type:

1. Enter the Start Time and End Time search parameters.

2. From the All Types list, select the log type(s) that you want to retrieve, and then click

Search. The logs are listed by time, user name, and event (if applicable).

3. To view detailed information about a specific log, click the log. The information is

displayed in the System Log Information box.

Page 83

Configuring System Settings

Backing Up Logs

To back up a log:

1. Click Backup. The Save As window opens.

2. By default, the backup file is named LogBackup[YYYY-MM-DD].txt. Rename the file if

you want, locate the directory where you want to save the file, and then click Save.

Deleting Logs

To delete all logs:

1. Click Clear.

2. A confirmation message appears. Click OK to continue. All of the logs that you have not

backed up are deleted.

Viewing Online Users

You can see which users are currently online on the Setup  Information  Online User page. The users are listed by user name, IP address, and login time. To refresh the list, click Refresh.

Page 84

2MP/4MP Low Light WDR IP Camera User Guide

Page 85

OPERATIONAL

VIDEO STANDARD

NTSC/PAL

SCANNING SYSTEM

Progressive scan

IMAGE SENSOR

1/2.8" 2Megapixel progressive scan CMOS

NUMBER OF PIXELS (H × V)

2MP - 1920x1080

MINIMUM ILLUMINATION

Color: 0.001Lux @f/1.6, B/W: 0Lux @f/1.6(IR on)

S/N RATIO

50db minimum

ELECTRONIC SHUTTER SPEED

IR DISTANCE

60m

DAY/NIGHT

Mechanical ICR (ON / OFF / AUTO selectable)

BACKLIGHT COMPENSATION

BLC / HLC / WDR / SAC(Scene Adaptive Control)

Auto/Natural/Street Lamp/Outdoor/Manual/ Customize

GAIN CONTROL

Auto/Manual

NOISE REDUCTION

3DNR

PRIVACY MASKING

4 configurable windows

ELECTRONIC IMAGE STABILIZATION

HBL2GR1V: OFF/ON

DEFOG

Auto/Manual/Off

HBW2GR3V: 5-60mm MFZ, HALL IRIS(Extended Focal Depth), optical zoom 12x lens F1.6

HBW2GR1V: 2.7-13.5 mm MFZ, DC IRIS, optical zoom 5x lens F1.6

zoom 4x lens F1.6

HBW2GR3V: H: 62° - 6°, V: 34° - 4°

HBW2GR1V: H: 110° - 32°, V: 59° - 19°

HBL2GR1V: H: 102° - 35°, V: 54° - 21°

AUDIO/TWO-WAY

Line In/Out

ALARM INPUT/OUTPUT

2 In / 1 Out

ANALOG OUTPUT SUPPORT

Twin outputs (for adjustment only)

HBW2GR3V, HBW2GR1V: RJ-45 (10/100Base-T) HBL2GR1V: RJ-45 (100/1000Base-T)

Appendix A Technical Specifications

10 Appendix A Technical Specifications

HBW2GR3V/HBW2GR1V/HBL2GR1V Bullet Camera

Table 10-1 HBW2GR3V/HBW2GR1V/HBL2GR1V Specifications

Auto/Manual, 1/3(4) ~1/100000s

WIDE DYNAMIC RANGE (WDR)

WHITE BALANCE

LENS

ANGLE OF VIEW

ETHERNET

HBL2GR1V: 140dB (50/60fps off) HBW2GR1V/HBW2GR3V:

120dB (50/60fps off)

Region

HBW2GR3V, HBW2GR1V: Not supported

HBL2GR1V: 2.7-12 mm MFZ, HALL IRIS(Extended Focal Depth), optical

Page 86

2MP/4MP Low Light WDR IP Camera User Guide

IP SPECIFICATIONS

VIDEO COMPRESSION

H.265+, H.265, H.264 and MJPEG bit rate control (CBR and VBR)

16:9

1080p (1920×1080)/ 720p (1280×720)

4:3

1.3M (1280×960)/VGA (640×480)

OTHER

D1 (704×576/704×480)/ CIF (352×288/352×240)

MAIN SUB STREAM

D1 (1-50/60fps WDR off)

HBW2GR3V, HBW2GR1V: 1080P (1-25/30fps) HBL2GR1V: 1080P (1-50/60fps WDR off)

HBW2GR3V, HBW2GR1V: Simultaneous Main stream and Third stream

AUDIO COMPRESSION

G.711a/ G.711Mu/ AAC/G.726

AUDIO STREAM

Full duplex, simplex

SUPPORTED WEB BROWSERS

IE11/Chrome(with application)/Firefox(earlier than 52.0 version)

SUPPORTED OS

Windows® 7 32-bit/64-bit; Windows® 10 32-bit/64-bit

HTTP; HTTPs; TCP; ARP; RTSP; RTP; UDP; SMTP; FTP; DHCP; DNS;

ICMP;SNMP

COMPATIBILITY

ONVIF Profile S, G and Q

MAXIMUM USERS ACCESS

20 users

HEAT MAP

HBL2GR1V: Support

HBW2GR1V/HBW2GR3V: Motion Detection/Video Tampering/Face

EVENT LINKAGE

EVENT OUTPUT

Trigger line/Intrusion/Loitering available now (Please

ADVANCED

ANALYTICS

ANALYTICS OUTPUT

Capacity Max 128GB

Event trigger recording; Continuous and scheduled recording;

English, Arabic, Czech, Dutch, French, German, Italian, Japanese,

RESOLUTION

STREAM

FRAME RATE

THIRD STREAM

SUPPORTED PROTOCOLS SUPPORTED PROTOCOLS*

SECURITY

EVENT TYPE

BUILT-IN ALARM & EVENT

1080P (1-50/60fps WDR off)

at 1080P (Main stream +Third stream <=68fps, WDR off, 2nd stream off) HBL2GR1V: Simultaneous Main stream and Third stream at 1080P (Main stream at 50/60fps WDR off, Third stream at 50/60fps WDR off)

DDNS; PPPOE; IPv4/v6; QoS; UPnP; NTP; Bonjour; 802.1x; Multicast;

User account and password protection HTTPS, IP Filter, IEEE 802.1x, Digest authentication, User access log, TLS1.2, AES-256, SSH/Telnet closed, FTP disabled, PCI-DSS compliance, Hardware chipset for private key

Detection/SD Card Error/SD Card Capacity Warning/Audio Detection/ Object Abandoned/Object Missing/Tripwire/Intrusion HBL2GR1V: Motion Detection/Video Tampering/Face Detection/ SD Card Error/SD Card Capacity Warning/Audio Detection/Object Abandoned/Object Missing/People counting

Recording on SD card, Relay output, Email, Snapshot

ONVIF, ISOM

UPLOADABLE VIDEO ANALYTICS (HBL2GR1V ONLY)

MICRO SD

MICRO SD FUNCTION

LANGUAGES SUPPORTED

BASIC

LICENSED

download from www.honeywellvideo.com. Free of Charge, but please email to VAlicensing@Honeywell.com to get license.)

IntrusionTrace/LoiterTrace for advanced applications coming soon. ( Need to purchase separately)

ISOM event output, Metadata

Micro SDHC Capacity Max 32GB Micro SDXC

Automatic recording when network fails

Korean, Polish, Portuguese, Russian, Simplified Chinese, Spanish, Turkish

Page 87

ELECTRICAL

POWER SUPPLY

PoE+(802.3at) Class 4/12VDC/AC24V

LONG DISTANCE POE SUPPORT

3X POE (300m @100Mbps)

AC FREQUENCY

50/60 Hz

HBW2GR3V: Max 17.3W ; HBW2GR1V: Max 20.5W HBL2GR1V: Max 17W

AUXILIARY POWER SUPPLY

2.0W, DC12V (+/-5%)

MECHANICAL

DIMENSIONS

11.1 × 4.3 in. (281.0 × 110.0 mm)

Product weight: 4.70lb (2130g) Package Weight: 6.28lb (2847g)

CONSTRUCTION

Die-cast aluminum housing with powder coat

CONSTRUCTION COLOR

RAL 9003 (White) and RAL 7022 (Grey)

ENVIRONMENTAL

OPERATING TEMPERATURE

–40°F to 140°F (–40°C to 60°C)

RELATIVE HUMIDITY

0% to 95%, non-condensing

GORE VENTS

Yes

INGRESS PROTECTION

IP 67

IMPACT RESISTANCE

IK10

HEATER, FAN OPTION

Heater

REGULATORY

EMISSIONS

FCC Part 15, CE (EN 55032); Complies with RCM (AS/NZS)

IMMUNITY

CE (EN 50130-4)

ROHS

EN50581

POWER CONSUMPTION

WEIGHT

Appendix A Technical Specifications

SAFETY

North America UL Listed to UL/CSA 60950-1, CE (EN 60950-1); North America UL Listed to UL/CSA 60950-22, CE (EN 60950-22)

Page 88

2MP/4MP Low Light WDR IP Camera User Guide

OPERATIONAL

VIDEO STANDARD

NTSC/PAL

SCANNING SYSTEM

Progressive scan

IMAGE SENSOR

1/2.8” 2 Megapixel progressive scan CMOS

NUMBER OF PIXELS (H × V)

2MP - 1920x1080

MINIMUM ILLUMINATION

Color: 0.001Lux @f/1.6, B/W: 0.001Lux @f/1.6

S/N RATIO

50 db minimum

ELECTRONIC SHUTTER SPEED

Auto/Manual, 1/3~1/100000s

DAY/NIGHT

Mechanical ICR (ON / OFF / AUTO selectable)

BACKLIGHT COMPENSATION

BLC / HLC / WDR /SAC(Scene Adaptive Control)

HCL2GV: 140dB (50/60fps off) HCW2GV: 120dB (50/60fps off)

WHITE BALANCE

Auto/Natural/Street Lamp/Outdoor/Manual/Customize Region

GAIN CONTROL

Auto/Manual

NOISE REDUCTION

3D Noise Reduction (ON / OFF selectable)

PRIVACY MASKING

Up to 4 configurable areas

ELECTRONIC IMAGE STABILIZATION

DEFOG

Auto/Manual/Off

LENS

Option, support DC-Iris

AUDIO/TWO-WAY

Line In/Out, 1 built-in Mic

ALARM INPUT/OUTPUT

2 in / 1 out

ANALOG OUTPUT SUPPORT

Supported

HCW2GV: RJ-45 (10/100 Base-T) HCL2GV: RJ-45 (100/1000 Base-T)

HCL2GV/HCW2GV Box Camera

Table 10-2 HCL2GV/HCW2GV Specifications

WIDE DYNAMIC RANGE (WDR)

HCW2GV: Not supported HCL2GV: ON/OFF

ETHERNET

Page 89

IP SPECIFICATIONS

H.265+, H.265, H.264 and MJPEG bit rate control (CBR and VBR)

16:9

1080p (1920×1080)/ 720p (1280×720)

4:3

1.3M (1280×960)/VGA (640×480)

OTHER

D1 (704×576/704×480)/ CIF (352×288/352×240)

MAIN STREAM

1080P (1~50/60fps WDR off)

SUB STREAM

D1 (1~50/60fps WDR off)

HCL2GV: 1080P (1~50/60fps WDR off) HCW2GV: 1080P (1~25/30fps)

stream at 50/60fps WDR off, Third stream at 50/60fps WDR off)

AUDIO COMPRESSION

G.711a/ G.711Mu/ AAC/G.726

AUDIO STREAM

Full duplex, simplex

SUPPORTED WEB BROWSERS

IE11/Chrome(with application)/Firefox(earlier than 52.0 version)

SUPPORTED OS

Windows® 7 32-bit/64-bit; Windows® 10 32-bit/64-bit

HTTP; HTTPs; TCP; ARP; RTSP; RTP; UDP; SMTP; FTP; DHCP; DNS;

ICMP;SNMP

COMPATIBILITY

ONVIF Profile S, G and Q

MAXIMUM USERS ACCESS

20 users

User account and password protection HTTPS, IP Filter, IEEE 802.1x,

private key

HEAT MAP

HCL2GV: Support

HCW2GV: Motion Detection/Video Tampering/Face Detection/ SD

Abandoned/Object Missing/People counting

EVENT

Trigger line/Intrusion/Loitering available now (Please

ADVANCED

ANALYTICS

ANALYTICS OUTPUT

Capacity Max 128GB

Event trigger recording

Automatic recording when network fails

English, Arabic, Czech, Dutch, French, German, Italian, Japanese,

Turkish

VIDEO COMPRESSION

RESOLUTION

Appendix A Technical Specifications

FRAME RATE

THIRD STREAM

SUPPORTED PROTOCOLS*

SECURITY

EVENT TYPE BUILT-IN ALARM & EVENT

LINKAGE

OUTPUT

HCW2GV: Simultaneous Main stream and Third stream at 1080P (Main

stream +Third stream <=68fps, WDR off, 2nd stream off) HCL2GV: Simultaneous Main stream and Third stream at 1080P (Main

DDNS; PPPOE; IPv4/v6; QoS; UPnP; NTP; Bonjour; 802.1x; Multicast;

Digest authentication, User access log, TLS1.2, AES- 256, SSH/Telnet closed, FTP disabled, PCI-DSS compliance, Hardware chipset for

Card Error/SD Card Capacity Warning/Audio Detection/ Object Abandoned/Object Missing/Tripwire/Intrusion HCL2GV: Motion Detection/Video Tampering/Face Detection/ SD Card Error/SD Card Capacity Warning/Audio Detection/Object

Recording on SD card, Relay output, Email, Snapshot

ONVIF, ISOM

download from www.honeywellvideo.com. Free of Charge, but please email to VAlicensing@Honeywell.com to get license.)

IntrusionTrace/LoiterTrace for advanced applications coming soon. (

Need to purchase separately)

UPLOADABLE VIDEO ANALYTICS (HCL2GV ONLY)

BASIC

LICENSED

ISOM event output, Metadata

MICRO SD

MICRO SD FUNCTION

LANGUAGES SUPPORTED

Micro SDHC Capacity Max 32GB Micro SDXC

•

• Continuous and scheduled recording

•

Korean, Polish, Portuguese, Russian, Simplified Chinese, Spanish,

Page 90

2MP/4MP Low Light WDR IP Camera User Guide

ELECTRICAL

POWER SUPPLY

PoE(802.3af) Class 0/12VDC/24VAC

LONG DISTANCE POE SUPPORT

3X POE (300m @100Mbps)

AC FREQUENCY

50/60 Hz

HCW2GV: Max 10W HCL2GV: Max 9.5W

AUXILIARY POWER SUPPLY

2.0W, DC12V (+/-5%)

MECHANICAL

DIMENSIONS

125.0×75.8×69.0 mm (4.92×2.98×2.72 in.)

HCW2GV: Product weight: 535g (1.18lb); Package Weight:

755g (1.66lb)

CONSTRUCTION

Die-cast aluminum housing with powder coat

CONSTRUCTION COLOUR

RAL 9003 (White) and RAL 7022 (Grey)

ENVIRONMENTAL

OPERATING TEMPERATURE

–30°C to 60°C (–22°F to 140°F)

RELATIVE HUMIDITY

0% to 95%, non-condensing

REGULATORY

EMISSIONS

FCC Part 15, CE (EN 55032); Complies with RCM (AS/NZS)

IMMUNITY

CE (EN 50130-4)

60950-1)

ROHS

EN50581

POWER CONSUMPTION

WEIGHT

SAFETY

756g (1.67lb) HCL2GV: Product weight: 534g (1.18lb); Package Weight:

North America UL Listed to UL/CSA 60950-1, CE (EN

Page 91

OPERATIONAL

VIDEO STANDARD

NTSC/PAL

SCANNING SYSTEM

Progressive scan

H3W2GR1V: 1/2.8" 2Megapixel progressive scan CMOS

H3W4GR1V: 1/3" 4Megapixel progressive scan CMOS

NUMBER OF PIXELS (H × V)

H3W2GR1V: Color: 0.001Lux @f/1.6, B/W:0Lux@f/1.6(IR on)

H3W4GR1V: Color : 0.01Lux @f/1.6, B/W : 0Lux@f/1.6(IR on)

S/N RATIO

50db minimum

ELECTRONIC SHUTTER SPEED

IR DISTANCE

20m

DAY/NIGHT

Mechanical ICR (ON / OFF / AUTO selectable)

BACKLIGHT COMPENSATION

BLC / HLC / WDR /SAC(Scene Adaptive Control)

WIDE DYNAMIC RANGE(WDR)

120dB (50/60fps off)

WHITE BALANCE

Auto/Natural/Street Lamp/Outdoor/Manual/Customize Region

GAIN CONTROL

Auto/Manual

NOISE REDUCTION

3D Noise Reduction (ON / OFF selectable)

PRIVACY MASKING

Up to 4 configurable areas

DEFOG

Auto/Manual/Off

LENS

2.7-13.5 mm MFZ, DC IRIS, optical zoom 5x lens F1.6

H3W2GR1V: FOV depending on different resolution H: 110° - 32°, V: 59° - 19°

H3W4GR1V: FOV depending on different resolution H: 110° - 30°, V: 53° - 18°

AUDIO/TWO-WAY

Line In/Out, 1 built-in Mic

ALARM INPUT/OUTPUT

2 In / 1 Out

ANALOG OUTPUT SUPPORT

Supported

ETHERNET

RJ-45 (10/100Base-T)

Appendix A Technical Specifications

H3W2GR1V/H3W4GR1V Indoor Dome Camera

Table 10-3 H3W2GR1V/H3W4GR1V Specifications

IMAGE SENSOR

2MP - 1920x1080

MINIMUM ILLUMINATION

Auto/Manual, 1/3~1/100000s

ANGLE OF VIEW

Page 92

2MP/4MP Low Light WDR IP Camera User Guide

IP SPECIFICATIONS

VIDEO COMPRESSION

H.265+, H.265, H.264 and MJPEG bit rate control (CBR and VBR)

H3W2GR1V: 1080p (1920×1080)/ 720p (1280×720) H3W4GR1V: 3M (2304×1296)/1080p (1920×1080)/ 720p (1280×720)

4:3

1.3M (1280×960)/VGA (640×480)

H3W2GR1V: D1 (704×576/704×480)/ CIF (352×288/352×240)

(704×576/704×480)/ CIF(352×288/352×240)

MAIN STREAM

H3W2GR1V: 1080P(1~50/60fps WDR off) H3W4GR1V: 4M(1~25/30fps)

H3W2GR1V: D1(1-50/60fps WDR off) H3W4GR1V: D1(125/30fps)

THIRD STREAM

H3W2GR1V: 1080P(1-25/30fps) H3W4GR1V: 4M(1~25/30fps)

H3W2GR1V: Simultaneous Main stream and Third stream at 1080P (Main

stream +Third stream <=34fps, 2nd stream off)

AUDIO COMPRESSION

G.711a/ G.711Mu/ AAC/G.726

AUDIO STREAM

Full duplex, simplex

SUPPORTED WEB BROWSERS

IE11/Chrome(with application)/Firefox(earlier than

52.0 version)

SUPPORTED OS

Windows® 7 32-bit/64-bit; Windows® 10 32-bit/64-bit

HTTP; HTTPs; TCP; ARP; RTSP; RTP; UDP; SMTP;FTP; DHCP; DNS; DDNS;

ICMP;SNMP

COMPATIBILITY

ONVIF Profile S, G and Q

MAXIMUM USERS ACCESS

20 users

User account and password protection HTTPS, IP Filter, IEEE 802.1x,

key

Motion Detection/Video Tampering/Face Detection/ SD Card Error/SD

Missing/Tripwire/ Intrusion

EVENT LINKAGE

EVENT OUTPUT

ONVIF, ISOM

MICRO SD

Micro SDHC Capacity Max 32GB Micro SDXC Capacity Max 128GB

Event trigger recording

fails

English, Arabic, Czech, Dutch, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Simplified Chinese, Spanish, Turkish

ELECTRICAL

POWER SUPPLY

PoE(802.3af) Class 0/12VDC/24VAC

LONG DISTANCE POE SUPPORT

3X POE (300m @100Mbps)

AC FREQUENCY

50/60 Hz

H3W2GR1V: 11W H3W4GR1V: 10.5W

AUXILIARY POWER SUPPLY

2.0W, DC12V (+/-5%)

16:9

RESOLUTION

FRAME RATE

OTHER

SUB

STREAM

H3W4GR1V: 4M(2688x1520)/(2560x1440), /D1

SUPPORTED PROTOCOLS*

SECURITY

BUILT-IN ALARM & EVENT

MICRO SD FUNCTION

LANGUAGES SUPPORTED

EVENT TYPE

stream +Third stream <=68fps, WDR off, 2nd stream off) H3W4GR1V: Simultaneous Main stream and Third stream at 4MP (Main

PPPOE; IPv4/v6; QoS; UPnP; NTP; Bonjour; 802.1x; Multicast;

Digest authentication, User access log, TLS1.2, AES-256, SSH/Telnet closed, FTP disabled, PCI-DSS compliance, Hardware chipset for private

Card Capacity Warning/Audio Detection/ Object Abandoned/Object

Recording on SD card, Relay output, Email, Snapshot

Continuous and scheduled recording Automatic recording when network

POWER CONSUMPTION

Page 93

MECHANICAL

DIMENSIONS

4.96 × 4.80 in. (126.0 × 122.0 mm)

H3W2GR1V: Product weight: 1.14lb (519g) Package Weight: 2.07lb

CONSTRUCTION

Plastic

CONSTRUCTION COLOR

RAL 9003 (White)

ENVIRONMENTAL

OPERATING TEMPERATURE

–22°F to 140°F (–30°C to 60°C)

RELATIVE HUMIDITY

0% to 95%, non-condensing

REGULATORY

EMISSIONS

FCC Part 15, CE (EN 55032); Complies with RCM (AS/ NZS)

IMMUNITY

CE (EN 50130-4)

SAFETY

North America UL Listed to UL/CSA 60950-1, CE (EN 60950-1)

ROHS

EN50581

Appendix A Technical Specifications

WEIGHT

(937g) H3W4GR1V: Product weight: 1.14lb (516g) Package Weight:

2.04lb (924g)

Page 94

2MP/4MP Low Light WDR IP Camera User Guide

OPERATIONAL

VIDEO STANDARD

NTSC/PAL

SCANNING SYSTEM

Progressive scan

H4W2GR1V, H4L2GR1V: 1/2.8" 2 Megapixel

H4W4GR1V: 1/3" 4 Megapixel progressive scan CMOS

H4W2GR1V, H4L2GR1V:2MP - 1920x1080 H4W4GR1V: 4MP - 2560x1440/2688x1520

H4W2GR1V, H4L2GR1V: Color : 0.001Lux @f/1.6,

@f/1.6(IR on)

S/N RATIO

50 db minimum

ELECTRONIC SHUTTER SPEED

Auto/Manual, 1/3~1/100000s

IR DISTANCE

50m

DAY/NIGHT

Mechanical ICR (ON / OFF / AUTO selectable)

BACKLIGHT COMPENSATION

BLC/HLC/WDR/SAC(Scene Adaptive Control)

H4L2GR1V: 140 dB (50/60fps off) H4W4GR1V,H4W2GR1V: 120 dB (50/60fps off)

WHITE BALANCE

Auto/Natural/Street Lamp/Outdoor/Manual Customize Region

GAIN CONTROL

Auto/Manual

NOISE REDUCTION

3D Noise Reduction (ON / OFF selectable)

PRIVACY MASKING

Up to 4 configurable areas

ELECTRONIC IMAGE STABILIZATION

H4W2GR1V, H4W4GR1V: Not supported H4L2GR1V: Off/On

DEFOG

Auto/Manual/Off

H4W2GR1V, H4W4GR1V: 2.7-13.5 mm MFZ, DC

Focal Depth), optical zoom 4x lens F1.6

H4W2GR1V: FOV depending on different resolution, H: 110° - 32°, V:

53° - 18°

AUDIO/TWO-WAY

Line In/Out

ALARM INPUT/OUTPUT

2 In/1 Out

ANALOG OUTPUT SUPPORT

Supported

H4W2GR1V, H4W4GR1V: RJ-45 (10/100Base-T) H4L2GR1V: RJ-45 (100/1000Base-T)

H4W2GR1V/H4L2GR1V/H4W4GR1V Outdoor Dome Camera

Table 10-4 H4W2GR1V/H4L2GR1V/H4W4GR1V Specifications

IMAGE SENSOR

NUMBER OF PIXELS (H×V)

MINIMUM ILLUMINATION

WIDE DYNAMIC RANGE(WDR)

LENS

ANGLE OF VIEW

progressive scan CMOS

B/W : 0Lux @f/1.6(IR on) H4W4GR1V: Color : 0.01Lux @f/1.6, B/W : 0Lux

IRIS, optical zoom 5x lens F1.6 H4L2GR1V: 2.7-12 mm MFZ, HALL IRIS(Extended

59° - 19° H4L2GR1V: FOV depending on different resolution H: 102° - 35°, V: 54° - 21°

H4W4GR1V: FOV depending on different resolution H: 110° - 30°, V:

ETHERNET

Page 95

IP SPECIFICATIONS

VIDEO COMPRESSION

H.265+, H.265, H.264 and MJPEG bit rate control (CBR and VBR)

H4W2GR1V, H4L2GR1V: 1080p (1920×1080)/ 720p (1280×720)

(1280×720)

4:3

1.3M (1280×960)/VGA (640×480)

H4W2GR1V, H4L2GR1V: D1 (704×576/704×480)/ CIF

(704×576/704×480)/ CIF (352×288/352×240)

H4W2GR1V, H4L2GR1V: 1080P (1~50/60fps WDR off) H4W4GR1V: 4M (1~25/30fps)

H4W2GR1V, H4L2GR1V: D1 (1~50/60fps WDR off) H4W4GR1V: D1 (1~25/30fps)

H4W2GR1V: 1080P (1-25/30fps)

H4W4GR1V: 4M(1~25/30fps)

H4W2GR1V: Simultaneous Main stream and Third stream at 1080P

stream +Third stream <=34fps, 2nd stream off)

AUDIO COMPRESSION

G.711a/ G.711Mu/ AAC/G.726

AUDIO STREAM

Full duplex, simplex

SUPPORTED WEB BROWSERS

IE11/Chrome(with application)/Firefox(earlier than 52.0 version)

SUPPORTED OS

Windows® 10 32-bit/64-bit

HTTP; HTTPs; TCP; ARP; RTSP; RTP; UDP; SMTP; FTP; DHCP; DNS;

ICMP; SNMP

COMPATIBILITY

ONVIF Profile S, G and Q

MAXIMUM USERS ACCESS

20 users

User account and password protection HTTPS, IP Filter, IEEE 802.1x,

key

HEAT MAP

H4L2GR1V: Support

H4W2GR1V, H4W4GR1V: Motion Detection/Video Tampering/Face

Detection/Object Abandoned/Object Missing/People counting

EVENT LINKAGE

Recording on SD card, Relay output, Email, Snapshot

EVENT OUTPUT

ONVIF, ISOM

UPLOADABLE

Trigger line/Intrusion/Loitering available now

to get license.)

ANALYTICS

ANALYTICS OUTPUT

Micro SDXC Capacity Max 128GB

• Event trigger recording

• Automatic recording when network fails

English, Arabic, Czech, Dutch, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Simplified Chinese, Spanish, Turkish

Appendix A Technical Specifications

16:9

RESOLUTION

OTHER

MAIN STREAM

SUB STREAM

FRAME RATE

THIRD STREAM

SUPPORTED PROTOCOLS*

H4W4GR1V: 3M (2304×1296)/1080p (1920×1080)/720p

(352×288/352×240)

H4W4GR1V: 4M (2688x1520)/ (2560x1440), /D1

H4L2GR1V: 1080P(1-50/60fps WDR off)

(Main stream +Third stream <=68fps, WDR off, 2nd stream off) H4L2GR1V: Simultaneous Main stream and Third stream at 1080P (Main stream at 50/60fps WDR off, Third stream at 50/60fps WDR off) H4W4GR1V: Simultaneous Main stream and Third stream at 4MP (Main

Windows® 7 32-bit/64-bit;

DDNS; PPPOE; IPv4/v6; QoS; UPnP; NTP; Bonjour; 802.1x; Multicast;

SECURITY

BUILT-IN

EVENT TYPE ALARM & EVENT

BASIC

VIDEO ANALYTICS (H4L2GR1V

ADVANCED

LICENSED

ONLY)

MICRO SD

MICRO SD FUNCTION

LANGUAGES SUPPORTED

Digest authentication, User access log, TLS1.2, AES-256, SSH/Telnet closed, FTP disabled, PCI-DSS compliance, Hardware chipset for private

Detection/SD Card Error/SD Card Capacity Warning/Audio Detection/ Object Abandoned/Object Missing/Tripwire/Intrusion H4L2GR1V: Motion Detection/Video Tampering/Face

Detection/SD Card Error/SD Card Capacity Warning/Audio

(Please download from www.honeywellvideo.com. Free of Charge, but please email to VAlicensing@Honeywell.com

IntrusionTrace/LoiterTrace for advanced applications coming soon. ( Need to purchase separately)

ISOM event output, Metadata

Micro SDHC Capacity Max 32GB

• Continuous and scheduled recording

Page 96

2MP/4MP Low Light WDR IP Camera User Guide

ELECTRICAL

POWER SUPPLY

PoE+(802.3at) Class 4/12VDC/24VAC

LONG DISTANCE POE SUPPORT

AC FREQUENCY

50/60 Hz

H4W2GR1V: Max 22W H4L2GR1V: Max 20.5W H4W4GR1V: Max 15W

AUXILIARY POWER SUPPLY

2.0W, DC12V (+/-5%)

MECHANICAL

DIMENSIONS

6.2" × 4.6" ( 159.0 × 118.0 mm)

H4W2GR1V: Product weight: 2.46lb (1117g) Package Weight:

2.47lb (1119g) Package Weight: 4.40lb (1997g)

CONSTRUCTION

Die-cast aluminum housing with powder coat

CONSTRUCTION COLOUR

RAL 9003 (White)

ENVIRONMENTAL

OPERATING TEMPERATURE

–40°F to 140°F (–40°C to 60°C)

RELATIVE HUMIDITY

0% to 95%, non-condensing

GORE VENTS

Yes

INGRESS PROTECTION

IP 67

IMPACT RESISTANCE

IK10

HEATER, FAN OPTION

Heater, Fan

REGULATORY

EMISSIONS

FCC Part 15, CE (EN 55032); Complies with RCM (AS/NZS)

IMMUNITY

CE (EN 50130-4)

North America UL Listed to UL/CSA 60950-1, CE (EN 60950-1); North America UL Listed to UL/CSA 60950-22, CE (EN 60950-22)

ROHS

EN50581

OPERATIONAL

VIDEO STANDARD

NTSC/PAL

SCANNING SYSTEM

Progressive scan

IMAGE SENSOR

1/2.8” 2Megapixel progressive scan CMOS

NUMBER OF PIXELS (H × V)

2MP - 1920x1080

MINIMUM ILLUMINATION

Color : 0.001Lux @f/2.0, B/W : 0Lux @f/2.0(IR on)

S/N RATIO

50 db minimum

ELECTRONIC SHUTTER SPEED

Auto/Manual, 1/3~1/100000s

IR DISTANCE

15m

DAY/NIGHT

Mechanical ICR (ON / OFF / AUTO selectable)

BACKLIGHT COMPENSATION

BLC / HLC / WDR /SAC(Scene Adaptive Control)

WIDE DYNAMIC RANGE(WDR)

120dB (50/60fps off)

WHITE BALANCE

Auto/Natural/Street Lamp/Outdoor/Manual/ Customize Region

GAIN CONTROL

Auto/Manual

NOISE REDUCTION

3D Noise Reduction (ON / OFF selectable)

PRIVACY MASKING

Up to 4 configurable areas

DEFOG

Auto/Manual/Off

LENS

2.8mm, F2.0

ANGLE OF VIEW

H: 110°, V: 58°

AUDIO/TWO-WAY

1 Built-in Mic

ETHERNET

RJ-45 (10/100Base-T)

3X POE (300m @100Mbps)

POWER CONSUMPTION

WEIGHT

SAFETY

4.40lb (1994g) H4L2GR1V: Product weight: 2.49lb (1130g) Package Weight: 4.42lb (2007g) H4W4GR1V: Product weight:

H2W2GR1 Micro Dome Camera

Table 10-5 H2W2GR1 Specifications

Page 97

IP SPECIFICATIONS

H.265+, H.265, H.264 and MJPEG Bit rate control (CBR and VBR)

16:9

1080p (1920×1080)/ 720p (1280×720)

4:3

1.3M (1280×960)/VGA (640×480)

OTHER

D1 (704×576/704×480)/ CIF (352×288/352×240)

MAIN STREAM

SUB STREAM

D1(1~50/60fps WDR off)

THIRD STREAM

Simultaneous Main stream and Third stream at 1080P (Main stream +Third stream <=68fps, WDR off, 2nd stream off)

AUDIO COMPRESSION

G.711a/ G.711Mu/ AAC/G.726

AUDIO STREAM

Simplex

SUPPORTED WEB BROWSERS

IE11/Chrome(with application)/Firefox(earlier 52.0 version)

Windows® 10 32-bit/64-bit

HTTP; HTTPs; TCP; ARP; RTSP; RTP; UDP; SMTP;FTP; DHCP; DNS;

QoS; UPnP; NTP; Bonjour; 802.1x; Multicast; ICMP; SNMP

COMPATIBILITY

ONVIF Profile S, G and Q

MAXIMUM USERS ACCESS

20 users

User account and password protection HTTPS, IP Filter, IEEE 802.1x,

private key

IN ALARM

Motion Detection/Video Tampering/Face Detection/ SD Card

Abandoned/Object Missing/ Tripwire/Intrusion

EVENT LINKAGE

EVENT OUTPUT

Micro SDHC Capacity Max 32GB Micro SDXC Capacity Max 128GB

Event trigger recording

• Automatic recording when network fails

English, Arabic, Czech, Dutch, French, German, Italian, Japanese,

Turkish

ELECTRICAL

POWER SUPPLY

PoE(802.3af) Class 0/12VDC

POWER CONSUMPTION

Max 4.4W

MECHANICAL

DIMENSIONS

109.9 x 55.0mm (4.33 x 2.17in.)

WEIGHT

Product weight: 334g (0.74lb) Package Weight: 730g (1.61lb)

CONSTRUCTION

Die-cast aluminum housing with powder coat

CONSTRUCTION COLOUR

RAL 9003 (White)

ENVIRONMENTAL

OPERATING TEMPERATURE

–30°C to 60°C (–40°F to 140°F )

RELATIVE HUMIDITY

0% to 95%, non-condensing

GORE VENTS

Yes

INGRESS PROTECTION

IP67

IMPACT RESISTANCE

IK10

REGULATORY

EMISSIONS

FCC Part 15, CE (EN 55032); Complies with RCM (AS/NZS)

IMMUNITY

CE (EN 50130-4)

SAFETY

North America UL Listed to UL/CSA 60950-1, CE (EN 60950-1)

ROHS

EN50581

VIDEO COMPRESSION

RESOLUTION

Appendix A Technical Specifications

1080P(1~50/60fps WDR off)

FRAME RATE

SUPPORTED OS

SUPPORTED PROTOCOLS*

SECURITY

EVENT TYPE

BUILT& EVENT

MICRO SD

MICRO SD FUNCTION

1080P(1-25/30fps)

Windows® 7 32-bit/64-bit;

DDNS; PPPOE; IPv4/v6;

Digest authentication, User access log, TLS1.2, AES-256, SSH/Telnet closed, FTP disabled, PCI-DSS compliance, Hardware chipset for

Error/SD Card Capacity Warning/Audio Detection/ Object

Recording on SD card, Email, Snapshot

ONVIF, ISOM

•

• Continuous and scheduled recording

LANGUAGES SUPPORTED

Korean, Polish, Portuguese, Russian, Simplified Chinese, Spanish,

Page 98

2MP/4MP Low Light WDR IP Camera User Guide

Page 99

Page 100

New Zealand: +64 9 623 5050

Honeywell Security Products Americas (Head Office)

2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA

www.honeywell.com/security

 +1 800 323 4576

Honeywell Security Europe/South Africa

Aston Fields Road, Whitehouse Industrial Estate Runcorn, WA7 3DL, United Kingdom

www.honeywell.com/security/uk

 +44 (0) 1928 754 028

Honeywell Security Products Americas Caribbean/Latin America

9315 NW 112th Ave.

Miami, FL 33178, USA

www.honeywell.com/security/clar

 +1 305 805 8188

Honeywell Security Asia Pacific

Building #1, 555 Huanke Road, Zhang Jiang Hi-Tech Park, Pudong New Area, Shanghai, 201203, China

www.asia.security.honeywell.com

 +86 400 840 2233

Honeywell Security Middle East/N. Africa

Emaar Business Park, Sheikh Zayed Road Building No. 2, Office No. 301 Post Office Box 232362 Dubai, United Arab Emirates

www.honeywell.com/security/me

 +971 (0) 4 450 5800

Honeywell Security Northern Europe

Ampèrestraat 41 1446 TR Purmerend, The Netherlands

www.honeywell.com/security/nl

 +31 (0) 299 410 200

Honeywell Security Deutschland

Johannes-Mauthe-Straße 14 72458 Albstadt, Germany

www.honeywell.com/security/de

 +49 (0) 7431 801-0

Honeywell Security France

Immeuble Lavoisier Parc de Haute Technologie 3-7 rue Georges Besse 92160 Antony, France

www.honeywell.com/security/fr

 +33 (0) 1 40 96 20 50

Honeywell Security Italia SpA

Via della Resistenza 53/59 20090 Buccinasco Milan, Italy

www.honeywell.com/security/it

 +39 (0) 2 4888 051

Honeywell Security España

Avenida de Italia, n° 7, 2a planta

C.T. Coslada 28821 Coslada, Madrid, Spain

www.honeywell.com/security/es

 +34 902 667 800

Honeywell Security Россия и СНГ

121059 Moscow, UI, Kiev 7 Russia

www.honeywell.com/security/ru

 +7 (495) 797-93-71

Honeywell Security and Fire (ASEAN)

Honeywell International Sdn Bhd Level 25, UOA Corp Tower, Lobby B Avenue 10, The Vertical, Bangsar South City 59200, Kuala Lumpur, Malaysia Visit Partner Connect: www.partnerconnect.honeywell.com Email: hsf.comms@honeywell.com Order management: customersupportHSFASEAN@honeywell.com Technical support: Vietnam: +84 4 4458 3369 Thailand: +66 2 0182439 Indonesia: +62 21 2188 9000 Malaysia: +603 7624 1530 Singapore: +65 3158 6830 Philippines: +63 2 231 3380

Honeywell Home and Building Technologies (India)

HBT India Buildings Unitech Trade Centre, 5th Floor, Sector – 43, Block C, Sushant Lok Phase – 1, Gurgaon – 122002, Haryana, India Visit Partner Connect: Email: HBT-IndiaBuildings@honeywell.com Toll Free No: 1-800-103-0339  +91 124 4975000

www.partnerconnect.honeywell.com

Honeywell Security and Fire (Korea)

Honeywell Co., Ltd. (Korea) 5F SangAm IT Tower, 434, Worldcup Buk-ro, Mapo-gu, Seoul 03922, Korea Visit: http://www.honeywell.com Email: info.security@honeywell.com Customer support: HSG-CS-KR@honeywell.com; +82 1522-8779  +82-2-799-6114

Honeywell Security & Fire (Pacific)

Honeywell Ltd 9 Columbia Way BAULKHAM HILLS NSW 2153 Visit: www.honeywellsecurity.com.au Email: hsf.comms.pacific@Honeywell.com Technical support: Australia: 1300 220 345

© 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

www.honeywell.com/security

+1 800 323 4576 (North America only)

https://www.honeywellsystems.com/ss/techsupp/index.html

Document 800-24234 Rev A –06/2018

Honeywell H3W2GR1V, H2W2GR1, H4L2GR1V, H3W4GR1V, HBL2GR1V User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

2MP/4MP Low Light WDR IP Camera

User Guide

About This Document

Overview of Contents

1 Accessing the Camera

Installing the IPC Tool Utility

Discovering Your Camera on the Network

Assigning a New IP Address to Your Camera

Upgrading the Camera’s Firmware

Accessing the Camera from a Web Browser

2 Logging In and Viewing Live Video

Logging In to the Web Client

Overview of the Live Interface

Configuring the Live Interface

Working in the Live Interface

Setting Up Live Video Streaming

Setting the Stream Type

Setting the Stream Protocol

Logging Out of the Web Client

3 Playing Back Recorded Video

Overview of the Playback Interface

Playback Controls

Video Clip Controls

Timeline

Playing Back Recorded Video

Downloading Recorded Video

Viewing Snapshots

4 Configuring Video and Audio Settings

Configuring Video Settings

Configuring Camera Settings

Profile

Picture

Exposure

Lighting Compensation

White Balance

Day and Night

IR Light

Defog

Managing Profiles

Configuring Streaming Settings

Format

Smart Codec

Resolution

Frame Rate

Bit Rate

I-Frame Interval

Watermark

Configuring Snapshot Settings

Snapshot Type

Image Size

Quality

Interval

Configuring Privacy Masks

Configuring the Channel Title

Configuring the Time Title

Configuring Customized Text Overlays

Configuring Picture Overlays

Configuring Regions of Interest

Configuring Zoom and Focus Settings

Configuring Audio Settings

5 Configuring Network Settings

Configuring TCP/IP

IPv4 Address Configuration

IPv6 Address Configuration

ARP/Ping

Configuring Network Connections

Configuring ONVIF

Configuring RSTP

Configuring PPPoE Settings

Configuring DDNS Settings

Filtering IP/MAC Addresses

Adding IP/Mac Addresses to the List of Approved Users

Editing IP/Mac Addresses

Deleting IP/Mac Addresses from the List of Approved Users

Configuring Email Settings

Configuring UPnP Port Mapping