Honeywell DT8050M Quick Installation Manual
DT8050M DUAL TEC® Motion Sensor - Quick Installation Guide
DT8050M DUAL TEC® Motion Sensor - Quick Installation Guide (FR)
DT8050M DUAL TEC® Motion Sensor - Quick Installation Guide (SP)
DT8050M DUAL TEC® Motion Sensor - Quick Installation Guide (PG)
1
6' 9" - 8' 9"
(2.1 - 2.7 m)
7' 6"
(2.3 m)
Optimal
Optimal
Optimal
Optimal
2
3
2
1
3
#6
(3.5 mm)
A
A
A
B B
B B
B B
A
B
#6 x 1 1/4"
(3.5 mm x 32 mm)
X X
4
Microwave Range Adjustment
Réglage de la portée Hyperfréquence
Ajuste del rango de detección Microondas
Ajuste de Alcance Microondas
* Factory default / Réglage usine /
Defecto de fábrica / Padrão de fábrica
ON
LED
*
Not Used
Not Used
Not Used
Not Used
MW
SENSITIVITY
MAX
*
MIN
*
Internal EOL Resistor DIP Switches
Résistance interne EOL commutateur DIP
Interruptores DIP internos EOL Resistor
EOL interno Resistor DIP Switches
EOL
KOhm
ON
1 2.2 5.62
*
DT8050M
AM LED
EOL
PULL
TO DISABLE
LOOK DOWN
LOOK DOWN
ON
OFF
ON
W1
MW
SENSITIVITY
MAX
KOhm
ON
1 2 2.2 5.6
- 2 -
5
24-20 AWG
(0.2-0.52mm
2
)
2
1
2
Tamper
30 mA
25 VDC
Trouble
30 mA
25 VDC
Power
18 mA
9 - 15 VDC
Alarm
30 mA
25 VDC
LED
0 VDC - V
supply
1.8 mA max
LED TBL T C V-V
+
T NCTBL
9 8 6 4 2 15 37
EOL
KOhm
ON
1 2.2 5.62
EOL
WIRING EXAMPLES / WIRING EXAMPLES / WIRING EXAMPLES
To connect alarm and tamper outputs (NO trouble) to one zone input:
All alarm and tamper events are “alarms” when the system is armed or
“fault” when disarmed.
(FR) To connect alarm and tamper outputs (NO trouble) to one zone
input: All alarm and tamper events are “alarms” when the system is
armed or “fault” when disarmed.
(SP) To connect alarm and tamper outputs (NO trouble) to one zone
input: All alarm and tamper events are “alarms” when the system is
armed or “fault” when disarmed.
(PG) To connect alarm and tamper outputs (NO trouble) to one zone
input: All alarm and tamper events are “alarms” when the system is
armed or “fault” when disarmed.
Zone
COM
Ground +12V
Control Panel
Zone
#
LED TBL T C V-V
+
T NCTBL
9 8 6 4 2 15 37
Sensor
EOL
KOhm
ON
1 2.2 5.62
EOL
(On-Board, Internal EOLR)
To connect all three outputs (sensor alarm, tamper and trouble) to
one zone input: All alarm, tamper and trouble events are “alarms” when
the system is armed or “fault” when disarmed.
FR) To connect all three outputs (sensor alarm, tamper and trouble)
to one zone input: All alarm, tamper and trouble events are “alarms”
when the system is armed or “fault” when disarmed.
ES) To connect all three outputs (sensor alarm, tamper and trouble)
to one zone input: All alarm, tamper and trouble events are “alarms”
when the system is armed or “f
ault” when disarmed.
PG) To connect all three outputs (sensor alarm, tamper and trouble)
to one zone input: All alarm, tamper and trouble events are “alarms”
when the system is armed or “fault” when disarmed.
Zone
COM
Ground
Zone
#
+12V
Control Panel
(On-Board, Internal EOLR)
LED TBL T C V-V
+
T NCTBL
9 8 6 4 2 15 37
EOL
KOhm
ON
1 2.2 5.62
EOL
Sensor
Loading...