How
to Program your
Honeywell Timetracker
M
T
Timetracker™ Dual
Timetracker™
Timetracker™
Wall Switch, CL600B-1009
Tabletop, CL600D-1005
Plug
,
CL600A-1001
This device automatically turns your light or appliance on and
of
times a day. Use
the Timetracker option is recommended for sunset
off
up to four
scheduling to ensure that your light goes on at dusk, regardless of the hour at
which dusk occurs. Timetracker automatically adjusts for the changing hour of
sunset, allowing the light to come on every day at nightfall.
Once you have started setting and programming, Timetracker will lock itself
if
50
seconds pass without a press
of
a button.
If
this happens, press LOCK,
then FUNCTION until you reach the place where you left off and continue.
For this reason, please read and understand this entire instruction booklet before
you begin setting and programming.
IMPORTANT
On the CL600B-1009 wall switch model only,
if
the display does not show
when you are ready to begin programming, the unit’s battery needs
to
recharging. With the unit wired and connected
the wall, place the switch
to AUTO. (This model MUST be switched to AUTO to recharge the battery.)
24
The battery will recharge sufficiently to bring the display on in
hours, but
will take several days to become fully charged. When the display comes on,
press RESET, and proceed with programming according to page
4.
FEATURES
PRESS TO STEP THROUGH
GEOGRAPHIC LOCATION,
DATE, TIME SETTINGS.
PRESS TO SET GEOGRAPHIC
LOCATION AND TO STEP
THROUGH
8
DAILY PROGRAMS
FOR TIME TRACKER FEATURE,
PRESS WHILE PROGRAMMING.
PRESSTOCANCELALL
SETTINGS AND
PROGRAMS; START OVER.
IS
ON WHEN APPLIANCE
LIGHT
IS
ON; OFF WHEN APPLIANCE
IS
OFF (INCLUDED ON
CL600A
-
1001 AND CL600D-1005 ONLY
a
DURING PROGRAMMING, TIMETRACKER WlLL
IF NONE
OF
THE BUlTONS ARE TOUCHED
PRESS TO
SET
(FOR TIME),
(FOR DATE).
PRESS TO
(FOR
(FOR DATE).
PRESS TO
SAVINGS TIME
STANDARD TIME (STD).
PRESS TO UNLOCK BEFORE
SETTlNG AND PROGRAMMING,
AND
PROGRAMMING.
SWITCH OFF WHILE PROGRAMMING,
ON
OR
AUTO TO RESUME NORMAL PROGRAM.
AUTOMATICALLY LOCK
FOR
50
SECONDS.
HOURS
OR
MONTH
SET
MINUTES
TIME),
OR
DAY
SET
FOR
DAYLIGHT
(DST)
OR
TO
LOCK AFTER
a
OFF
TO OVERRIDE PROGRAM,
12,784
2
DETERMINE
YOUR PROGRAM
Fill in the times on the dial below.
Start programming with your first
program time after midnight.
-
first time is an ON
program
1,
1.
and start with
time, start with
If
it is an OFF-time, skip
2.
Continue
If
this
through the day and evening,
making sure that all program times
are
in
sequence, and don't overlap.
Your setting cannot be
midnight, but can be
12:Ol
a.m.
ON AND
THREE TIMEWDAY ONCE/DAY
?z::zG>
12:OO
1159
OFF
p.m. or
-
EXAMPLES
OFF
?ZO:ZGIG>
ON AND
lZO:E&>
OFF
ON-'
CHANGING
TO
DAYLIGHT-SAVING
❏
PressLOCK.
FROM
STANDARD
TIME
(AND BACK)
Press DST/STD. The DST/STD indictor in the display will change, followed
by the appropriate change in time.
Press LOCK again.
CHANGING THE CALENDAR
After several months have passed, your calendar will be a few days ahead,
since each month in the Timetracker'
update your calendar as follows:
Press LOCK.
❏
Press FUNCTION until calendar appears.
❏
Press MIN./DAY for correct day and HRSJMO. for correct month,
necessary.
❏
Press LOCK again.
IN CASE
A
built-in rechargeable battery ensures that your Timetracker's program is not
OF
POWER OUTAGE
lost in case of a power failure. The battery is automatically recharged when
the Timetracker is normally wired or plugged in, and switched to the AUTO
position.
If you have any questions regarding the Timetracker, please contact
Honeywell Consumer Affairs toll
a.m.-4:00 p.m. Central time.
S.M.
Rev.
7-90
"
has only
30
days. If desired, you may
if
-
free at 1-800-468-1502, Monday-Friday,
Form
Number
@Honeywell.
69-0451-2
7:30
Inc.
1990
Loading...