Honeywell 8000 User Manual

DONE

M24083

DONE

M24085

TEST NUMBER

SYSTEM STATUS

Setup functions Setting & Options (factory

69-1871-1

SCHED HOLD

FAN

AUTO

SYSTEM

HEAT

Inside

M24079

0520 U/V lamp change

0530 Adaptive Intel-

0540 Program periods 4 4 periods (Wake,

0580 Compressor

0600 Heat temperature

0610 Cool temperature

0640 Clock format 12 12-hour time

0650 Extended fan

0660 Extended fan

0670 Keypad Lockout 0 Unlocked

Table 1. Installer Setup

reminder

ligent Recovery

protection

range stop

timer (heat)

timer (cool)

default in bold)

0 Off

1 365 calendar days

1 On

0 Off

Leave, Return, Sleep)

2 2 periods (Wake, Sleep)

5 5-minute compressor

off time

[Other options: 0–4 minutes]

90 Max. heat temperature

setting is 90°F (32°C)

[Other options: 40-89°F (4°C to 32°C)]

50 Min. cool temperature

setting is 50°F (10°C)

[Other options: 51-99°F (11°C to 37°C)]

24 24-hour time

0 Off

90 Fan runs for 90 seconds

after call for heat ends

0 Off

90 Fan runs for 90 seconds

after call for cooling ends

1 Partially locked 2 Fully locked

Setup functions Setting & Options (factory

0680 Heat temperature

0690 Cool temperature

0700 Temperature

0710 RESET 0 No reset

Table 1. Installer Setup

control

display offset

default in bold)

2 Standard temperature

control (recommended)

1 Select if inside tempera-

ture is consistently over setting

3 Select if inside tempera-

ture is consistently under setting

2 Standard temperature

control (recommended)

1 Select if inside tempera-

ture is consistently over setting

3 Select if inside tempera-

ture is consistently under setting

0 No offset

[Other options: -3, -2,

-1, 1, 2, 3°F (-1.5°C to

1.5°C)]

1 Reset installer options

& program schedule to factory default

INSTALLER SYSTEM TEST

The Installer Test is part of the Installer Setup Menu.

Enter the Installer System Test by entering the Installer

1. Setup and pressing t repeatedly until “Test” appears.

Use arrow to change test and system status as

2. required.

Press DONE to exit.

SYSTEM TESTS

Test the system’s heating, cooling, fan and emergency heat. Available tests vary by thermostat and system type.

System Test

Number

Test 1 Cooling System

Test 2 Fan System

Test 3 Heating System

Test 4 Emergency

Press the DONE button to exit the Installer System Test.

caution

Table 2. Installer System Test

Test Type System Status Number

Test

Heat Test

EQUIPMENT DAMAGE HAZARD. Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the compressor quickly.

and Description

0 Off 1 Compressor and

fan on

2 Second stage

compressor on

0 Off 1 Fan on

0 Off 1 Heat on 2 Second stage heat

(Aux. heat) on

3 Third stage heat

(Auxiliary heat) on

0 Off 1 Em. Heat and fan on 2 Auxiliary heat on

VisionPRO® 8000

Thermostats

INSTALLER SETUP AND

SYSTEM TEST POCKET GUIDE

INSTALLER SETUP

Press SYSTEM.

6 7 8 9

Press and hold these two blank buttons until the

DONE

CANCEL

SYSTEM

HEAT

M24080

DONE

FUNCTION

SETTING

M24082

2. display changes.

Use arrows to change settings as required.

Press DONE to exit and save settings.

INSTALLER SETUP FUNCTIONS

Available option and default settings vary by thermostat.

Setup functions Setting & Options (factory

0120 Year (rst two

0130 Year (second two

0140 Month 6 [Other options 1-12]

0150 Day 15 [Other options 1-31]

0160 Schedule format 4 7-day programming

Table 1. Installer Setup

digits)

default in bold)

20 (2000-2099)

21 (2100-2178)

06 (2006) [Other options 0-99]

0 Non-programmable

Setup functions Setting & Options (factory

0170 System type 1 1 heat / 1 cool Conv.

0180 Fan control

(heating)

0190 Changeover valve

(O/B terminal)

0200 Auxiliary heat 0 Electric backup heat

0210 External fossil

0220 First stage

0230 Second stage

fuel kit

compressor cycle rate

default in bold)

2 1 heat / 1 cool heat

pump (no Aux. heat) 3 Heat only (2 wire) 4 Heat only with fan 5 Hot water Series 20 6 Cool only 7 2 heat / 1 cool heat

pump (with Aux. heat) 8 2 heat / 2 cool multistage 9 2 heat / 1 cool multistage 10 1 heat / 2 cool multistage 11 2 heat / 2 cool heat pump

(no Aux. heat) 12 3 heat / 2 cool heat

pump (with Aux. heat)

0 Gas/Oil heat (equipment

controls heating fan)

1 Electric furnace (thermo-

stat controls heating fan)

0 Controls valve in cooling

1 Controls valve in heating

1 Fossil fuel backup heat

1 External fossil fuel kit

controls backup heat

0 Thermostat controls

backup heat (outdoor

sensor required)

3 Recommended

[Other options: 1–6]

3 Recommended

[Other options: 1–6]

Table 1. Installer Setup

Setup functions Setting & Options (factory

0240 First stage heat

cycle rate

0250 Second stage

heat cycle rate

0260 Third stage heat

cycle rate

0270 Emergency heat

cycle rate

0280 Backlight 0 Backlight on keypress

0300 Manual/auto

changeover

default in bold)

5 Gas or oil furnaces of

less than 90%

efciency

1 Steam or gravity 3 Hot water systems or fur-

naces of 90%+ efciency

9 Electric furnaces

[Other options: 1–12]

5 Gas or oil furnaces of

less than 90% efciency

1 Steam or gravity 3 Hot water systems or fur-

naces of 90%+ efciency

9 Electric furnaces

[Other options: 1–12]

9 Electric auxiliary heat

or electric furnaces

1 Steam or gravity 3 Hot water systems or fur-

naces of 90%+ efciency

5 Gas or oil furnaces of

less than 90% efciency [Other options: 1–12]

9 Electric auxiliary heat

or electric furnaces

1 Steam or gravity 3 Hot water systems or fur-

naces of 90%+ efciency

5 Gas or oil furnaces of

less than 90% efciency [Other options: 1–12]

1 Continuous backlight (re-

quires 24VAC connection)

0 Manual changeover

(Heat/Cool/Off)

1 Automatic changeover

(Heat/Cool/Auto/Off)

Table 1. Installer Setup

Setup functions Setting & Options (factory

0310 Auto changeover

deadband

0320 Temperature

display

0330 Daylight savings 1 Auto-change to daylight

0340 Remote sensor 0 No remote sensor

0350 Heat pump com-

pressor lockout

0360 Heat pump auxil-

iary lockout

0380 Dehumidication

Control

0500 Furnace lter

change reminder

0510 Humidier pad

change reminder

default in bold)

3 Heat/cool tempera-

ture 3°F apart (1.5°C)

[Other options: 2-9 (2°F9°F/1°C-5°C)]

0 Fahrenheit

1 Celsius

savings time (through

2006)

2 Auto-change to daylight

savings time (2007 and beyond)

0 Daylight savings time is

turned off

1 Outdoor sensor (display

only)

2 Outdoor sensor for con-

trol (select heat pumps)

3 Indoor sensor

0 Off

[Other options: 15, 20, 25, 30, 35, 40°F (-9.5°C to 7°C)]

0 Off

[Other options: 40, 45, 50, 55, 60°F (4.5°C to

15.5°C)]

0 Off

1 A/C runs to help

dehumidify

0 Off

1 10-day run time

(about 1 month)

2 30-day run time

(about 3 months)

3 60-day run time

(about 6 months)

4 90-day run time

(about 9 months)

5 120-day run time

(about 1 year)

6 365-day run time

(about 3 years)

0 Off

1 90 calendar days 2 180 calendar days 3 365 calendar days

Table 1. Installer Setup

Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers.

Automation and Control Solutions

Honeywell International Inc.

1985 Douglas Drive North

Golden Valley, MN 55422

Honeywell Limited-Honeywell Limitée

35 Dynamic Drive

Toronto, Ontario M1V 4Z9

http://yourhome.honeywell.com

2 3 4 5

Honeywell 8000 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual