Honeywell 4230A User Manual
IMAGETEAM™ 4230 Quick Start
Guide
Disclaimer
Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Hand Held Products to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Hand Held Products.
Hand Held Products shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
This document contains proprietary information which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hand Held Products.
© 2005 Hand Held Products, Inc. All rights reserved. Web Address: www.handheld.com
Microsoft Pocket PC 2002, Windows, Windows NT, Windows 2000, Windows ME, Windows XP, ActiveSync, Outlook, and the Windows logo are trademarks or registered trademarks of Microsoft Corporation.
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc.
Table of Contents |
|
Getting Started |
|
IT4230 with Green LED Aimer |
|
Imager Identification................................................................. |
1 |
Reading Techniques ................................................................ |
2 |
IT4230 Models......................................................................... |
3 |
Cordless System: Main Components ....................................... |
3 |
About the Battery ..................................................................... |
3 |
Proper Disposal of the Battery ............................................ |
4 |
Using the Imager with Bluetooth Devices ............................... |
4 |
Tested Bluetooth Adapters ................................................ |
4 |
Example of Connecting IT4230 with a PC ........................ |
5 |
Changing Bluetooth PIN Code .......................................... |
6 |
Out-of-Range Alarm ............................................................... |
6 |
Useful Menu Bar Codes ........................................................... |
6 |
Manual/Serial Trigger Mode .................................................... |
6 |
Presentation Mode ................................................................... |
6 |
Suffix Selections ..................................................................... |
7 |
Resetting the Standard Product Defaults .................................. |
7 |
To Add a Test Code I.D. Prefix to All Symbologies................. |
7 |
Reset Imager ........................................................................... |
8 |
Show Software Revision .......................................................... |
8 |
Programming Codes................................................................. |
9 |
Beeper and LED Sequences and Meaning ............................. |
10 |
Repairs .................................................................................... |
10 |
Maintenance............................................................................. |
10 |
Cleaning the Imager’s Window ....................................... |
10 |
Inspecting Cords and Connectors..................................... |
11 |
Troubleshooting .................................................................... |
11 |
Obtaining Factory Service ..................................................... |
12 |
Technical Support ................................................................. |
12 |
Statement of Agency Compliance ......................................... |
13 |
Patents ............................................................................ |
15 |
Solids and Water Protection............................................. |
15 |
Limited Warranty................................................................... |
15 |
i
ii
Getting Started
IT4230 with Green LED Aimer
Imager Identification
IMAGETEAM™ 4230 Quick Start Guide |
1 |
Reading Techniques
The imager has a view finder that projects a bright red or green aiming beam that corresponds to the imager’s horizontal field of view. The aiming beam should be centered over the bar code, but it can be positioned in any direction for a good read.
Linear bar code |
2D Matrix symbol |
The aiming beam is smaller when the imager is closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit. Symbologies with larger bars or elements (mil size) should be read farther from the unit. To read single or multiple symbols (on a page or on an object), hold the imager at an appropriate distance from the target, pull the trigger, and center the aiming beam on the symbol. If the code being scanned is highly reflective (e.g., laminated), it may be necessary to tilt the code up 15° to 18° to prevent unwanted reflection.
2 |
IMAGETEAM™ 4230 Quick Start Guide |
IT4230 Models
About the Battery
Use only the Li-ion battery packs provided by Hand Held Products. The use of any battery pack not sold by Hand Held Products will void your warranty and may result in damage to your unit.
Power is supplied to the cordless imager by a rechargeable battery that is integrated in the imager handle. Each imager is shipped with a battery.
Charging Information
The battery is designed to charge using a wall adapter.
Only use the battery charger supplied with the imager. Using another power supply may damage the imager.
Plug the adapter into the bottom of the imager’s handle.
IMAGETEAM™ 4230 Quick Start Guide |
3 |
Loading...