The Honeywell trademark is used under license from Honeywell
International inc. Honeywell International inc. makes no
representations or warranties with respect to this product.
La marque déposée Honeywell est utilisée avec autorisation
d'Honeywell International Inc. Honeywell international Inc. ne fait
aucune affirmation et n’offre aucune garantie au sujet de ce produit.
La marca Honeywell se usa bajo licencia otorgada por Honeywell
International Inc. Honeywell International Inc. no hace ningún tipo de
representación ni garantía con respecto a este producto.
Models / Modèles / Modelos
2111-2115
DIGITAL STEEL FIRE & SECURITY SAFE
COFFRE-FORT D'ACIER NUMÉRIQUE À
L'ÉPREUVE DU VOL ET DES INCENDIES
CAJA DE SEGURIDAD DIGITAL
DE ACERO CONTRA INCENDIO
Read this manual carefully and never store it inside the safe!
Lire attentivement ce manuel et ne jamais le garder à l’intérieur du coffre-fort !
¡Lea este manual cuidadosamente y nunca lo guarde dentro de la caja fuerte!
Digital Steel Fire & Security Safe
PACKAGE CONTENTS
1 – Digital Steel Fire & Security Safe
1 – Operation Manual
2 – Entry Keys
4 – “AA” Batteries
1 – Silica Gel Pack
Models 2111-2115
DO NOT RETURN SAFE TO STORE!
If there are any missing parts or you have
difficulty setting up or operating your safe,
please contact our Consumer Assistance
Department by telephone:
1-877-354-5457
(USA & Canada)
Monday–Friday
7am - 5pm PST
SETUP & OPERATION
STEP 1: INSTALL BATTERIES
For your convenience, we have included 4 “AA” Batteries that provide the power
for the electronic controls. These must be installed before using your safe.
1. Remove the battery compartment cover
located on the right side of the control panel by
pushing in and to the right.
2. Install the 4 “AA” batteries in the battery
compartment as illustrated on the inside of the
compartment.
3. If the batteries are put in correctly, the safe will
beep and the LCD readout will flash, then it will
GOOD”
read “
1.
2.
3.
PRODUCT OVERVIEW
A - Entry Key Hole
B - LED Display panel
C - Battery Comp. Cover
D - Door Hinges
E - Rubber Feet
F - Electronic Digital Keypad
G - Safe Cabinet Body
H - Safe Door
I - Serial Number Label
4. Once the batteries are properly installed,
replace the battery compartment cover.
4.
REPLACE BATTERIES:
For best results, it is recommended to replace
the batteries when they become weak as
shown on the Battery Power Level Indicator
(A) or at least once a year.
NOTE: It is NOT RECOMMENDED to use
Non-alkaline or rechargeable batteries.
If the batteries are removed or fail, the keypad memory will NOT be erased
and the active programmed code will still work once power has been
restored.
SETUP & OPERATION
SETUP & OPERATION
STEP 2: SET CALENDAR AND CLOCK
Once batteries are installed and the control pad is powered, the next step is to
begin by programming the clock and calendar. READ ENTIRE DIRECTIONS
AND WRITE DOWN DATE/DAY/TIME BEFORE PROGRAMMING. NOTE:
You must enter all information without delays. If the light goes off, you must
begin programming again.
1. With the safe door closed and locked, press
” key followed by the “9” key.
the “
The LCD readout will glow amber.
EXAMPLE
2. Enter the Year – 2 Digits
3. Enter the Month – 2 Digits
4. Enter the Date – 2 Digits
5. Enter the Day – 1 Digit (see chart below)
6. Enter the Hour – 2 Digits (see chart below)
7. Enter the Minutes – 2 Digits
DAY
Monday 1
Tuesday 2
Wednesday 3
Thursday 4
Friday 5
Saturday 6
Sunday 7
#
HOUR
##
1:00 am 01
2:00 am 02
3:00 am 03
4:00 am 04
5:00 am 05
6:00 am 06
7:00 am 07
8:00 am 08
When correctly entered, the LCD
readout will stop glowing and should
display the information you just
programmed.
2.
February =
3.
4.
Monday =
5.
9:26 am =
6.
1.
2010 =
th
30
=
9:26 am =
7.
HOUR
##
HOUR
##
9:00 am 09 5:00 pm 17
10:00 am 10 6:00 pm 18
11:00 am 11 7:00 pm 19
12:00 pm 12 8:00 pm 20
1:00 pm 13 9:00 pm 21
2:00 pm 14 10:00 pm 22
3:00 pm 15 11:00 pm 23
4:00 pm 16 12:00 am 00
STEP 3: UNLOCK AND OPEN THE SAFE
This safe is equipped with a dual digital/key lock system that requires entering
an active user code to unlock it and an entry key to open. It allows for two
separate reprogrammable active user codes.
The preset factory user codes are “
1 2 3 4” and “1 2 3 4 5 6”.
1. Begin by inserting the entry key into the
1.
cylindrical key hole on the left side of the
control panel.
2. On the keypad enter the
#” key, then the user code “1 2 3 4”,
“
followed by “
#” key again.
2.
3. If correct code is entered, OPEN will
3.
appear on the LCD panel, and you’ll hear a
chime tone indicating the safe is unlocked.
4. Within 5 seconds, turn the key to the right
4.
(clockwise) and pull the door open.
TO LOCK THE SAFE:
Carefully close the door, turn the key
counterclockwise to the left and remove.
The safe is now locked and an active user
code will need to be re-entered to open.
Loading...