The following products and systems on your vehicle emit radio waves when in
operation:
• Audio system
• Blind spot information system*
• Immobilizer system
• Bluetooth
• Bluetooth HandsFreeLink
®
Audio
®
• Collision Mitigation Braking
™
System
(CMBS™)
• HomeLink
Transceiver*
• HondaLink
• Remote engine starter*
• Remote transmitter
• Smart entry system*
• Tire Pressure Monitoring System
®
Universal
®
Each of the above complies with the appropriate requirements or the required
standards of the FCC (Federal Communications Commission) and Industry Canada,
described below:
As required by the FCC:
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
As required by Industry Canada:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
California Perchlorate Contamination Prevention Act
The airbags, seat belt tensioners, and CR-type batteries in this vehicle may
contain perchlorate materials—special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for more information.
Event Data Recorders
This vehicle is equipped with an event data recorder (EDR). The main purpose of
an EDR is to record, in certain crash or near crash-like situations, such as an air
bag deployment or hitting a road obstacle, data that will assist in understanding
how a vehicle’s systems performed. The EDR is designed to record data related to
vehicle dynamics and safety systems for a short period of time, typically
30 seconds or less. The EDR in this vehicle is designed to record such data as:
• How various systems in your vehicle were operating;
• Whether or not the driver and passenger safety belts were buckled/fastened;
• How far (if at all) the driver was depressing the accelerator and/or brake
pedal; and,
• How fast the vehicle was traveling.
These data can help provide a better understanding of the circumstances in
which crashes and injuries occur. NOTE: EDR data are recorded by your vehicle
only if a non-trivial crash situation occurs; no data are recorded by the EDR under
normal driving conditions and no personal data (e.g., name, gender, age, and
crash location) are recorded. However, other parties, such as law enforcement,
could combine the EDR data with the type of personally identifying data routinely
acquired during a crash investigation.
To read data recorded by an EDR, special equipment is required, and access to
the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other
parties such as law enforcement that have the special equipment can read the
information if they have access to the vehicle or the EDR.
The data belong to the vehicle owner and may not be accessed by anyone else
except as legally required or with the permission of the vehicle owner.
Service Diagnostic Recorders
This vehicle is equipped with service-related devices that record information
about powertrain performance. The data can be used to verify emissions law
requirements and/or help technicians diagnose and solve service problems. It may
also be combined with data from other sources for research purposes, but
it remains confidential.
California Proposition 65 Warning
WARNING: This product contains or emits chemicals known to the state of
California to cause cancer and birth defects or other reproductive harm.
*if equipped
INTRODUCTIONTABLE OF CONTENTS
This Owner’s Guide is intended to help you quickly get acquainted with your
2017 Honda Pilot. It provides basic information and instructions on technology and
convenience features, as well as emergency procedures and how to get assistance.
This guide is for vehicles sold in the United States and Canada. It covers all models,
so you may find descriptions of features and equipment that are not in your vehicle.
Images throughout this guide are from U.S. vehicles and represent features and
equipment that are available on some, but not all, models.
This guide is not intended to be a substitute for the Owner’s Manual. The Owner
Information CD enclosed in your glove box kit includes the Owner’s Manual,
Navigation Manual, and vehicle and tire warranties in electronic format. This
information can be viewed on a computer (PC or Mac platform) and saved or printed
for your reference. You can also visit owners.honda.com (U.S.) or myhonda.ca
(Canada) to view the complete and most current information.
If you are the first registered owner of your vehicle, you may request a complimentary
printed copy of the Owner’s Manual, Navigation Manual, or Vehicle Warranty within
the first six months of vehicle purchase. To request a copy, visit owners.honda.com
and create or log in to your account. In Canada, please request a copy from your
Honda dealer.
American Honda Motor Company strives to be proactive in protecting our
environment and natural resources. By using electronic delivery for a considerable
portion of the information typically found in a vehicle owner’s manual, we are further
reducing our impact on the environment.
Honda Automobile Customer Service
Your authorized Honda dealer should be able to answer any questions you have
about your vehicle. However, if you are dissatisfied with the information you receive,
you can call Honda Automobile Customer Service (see page 167).
Call (800) 999-1009 (U.S.) or (888) 946-6329 (Canada)
Honda Roadside Assistance
24-hour emergency road service is available to you in the United States and Canada
throughout your 3-year/36,000-mile warranty term. Services include jump starting,
flat tire and lockout assistance, towing, and more (limitations apply).
VISUAL INDEX .............................................................1
Steering Wheel and Nearby Controls ...................1
Dashboard and Ceiling Controls ............................2
SAFETY INFORMATION .............................................3
Important Safety Information .................................3
VOICE COMMAND INDEX .....................................168
INDEX ........................................................................170
™
.........................................146
VISUAL INDEX
Quickly locate items in the vehicle’s interior.
Steering Wheel and Nearby Controls
1114
1
Lights/turn signals/LaneWatch
button* p. 38, p. 39, p. 121
2
Brightness control p. 38
3
Wipers/washers p. 42
4
Cruise control*/Adaptive Cruise
Control (ACC)*/Lane Keeping Assist
System (LKAS) buttons*
p. 118, p. 119, p. 122
5
Horn
6
Voice recognition buttons
p. 85, p. 88, p. 95
7
Audio controls p. 62
8
Instrument panel p. 24Multi-information display (MID)
p. 28
1
131210
74596
823
VISUAL INDEX
9
INFO/RESET buttons p. 28
10
ENGINE START/STOP button p. 111
11
Door mirror controls p. 52
12
Vehicle Stability Assist (VSA) OFF
button p. 117Parking sensor system button* p. 125
Collision Mitigation Braking System
(CMBS) OFF button* p. 124
Road Departure Mitigation (RDM)
button* p. 123
Heated windshield button* p. 56
13
Heated steering wheel button* p. 56
14
ECON button p. 117
*if equipped*if equipped
| 1
SAFETYVISUAL INDEX
Dashboard and Ceiling Controls
111213
9
10
87
1
Color audio system* p. 64Touchscreen* p. 69Navigation system* p. 95
2
Rearview mirror p. 52
3
Hazard warning button
4
Climate control system p. 55
5
Seat heater/ventilation buttons*
p. 57
6
USB port(s)* p. 60
Accessory power socket p. 61
7
Rear entertainment system* p. 82
8
Hood release handle p. 149
9
Fuel fill door release button p. 130
Power tailgate button* p. 33
2
341
14
65
10
Parking brake p. 115
11
Power window switches p. 35
Door lock switches p. 34
12
Shifting p. 112
Intelligent Traction Management
button* p. 116
Auto idle stop OFF button* p. 116
13
Driving Position Memory System*
p. 51
14
(inside center console)
USB port p. 60
Accessory power socket p. 61
Auxiliary input jack p. 61
SAFETY INFORMATION
Your safety—and the safety of others—is very important and operating this vehicle
safely is an important responsibility. While we strive to help you make informed
decisions about safety, it is not practical or possible to warn you about all the
hazards associated with operating or maintaining your vehicle. Therefore, you must
use your own good judgment.
Important Safety Information
This guide explains many of your vehicle’s safety features and how to use them.
Please read this information carefully. Following the instructions below will also help
to keep you and your passengers safe.
Important Safety Precautions
• Always wear your seat belt.
• Secure all children in the proper restraint system.
• Be aware of airbag hazards.
• Don’t drink and drive.
• Pay appropriate attention to the task of driving safely.
• Control your speed.
• Keep your vehicle in safe condition.
Engaging in cell phone conversation or other activities that keep you from paying
close attention to the road, other vehicles, and pedestrians could lead to a crash.
Remember, situations can change quickly, and only you can decide when it is safe
to divert some attention away from driving.
Important Handling Information
Your vehicle has higher ground clearance than a
passenger vehicle designed for use only on pavement.
Higher ground clearance has many advantages for
off-highway driving. It allows you to travel over bumps,
obstacles, and rough terrain. It also provides good
visibility so you can anticipate problems earlier.
These advantages come at some cost. Because your vehicle is taller and rides
higher off the ground, it has a higher center gravity making it more susceptible to
tipping or roll over if you make abrupt turns. Utility vehicles have a significantly
higher rollover rate than other types of vehicles. In a rollover crash, an unbelted
person is significantly more likely to die than a person wearing a seat belt. As a
reminder, make sure you and your passengers always wear seat belts.
*if equipped
2 || 3
SAFETYSAFETY
Safety Messages
When you see the following messages throughout this guide, pay close attention.
You WILL be KILLED or SERIOUSLY HURT if you don’t follow
DANGER
instructions.
You CAN be KILLED or SERIOUSLY HURT if you don’t follow
WARNING
instructions.
You CAN be HURT if you don’t follow instructions.
CAUTION
This information is intended to help you avoid damage to your
NOTICE
vehicle, other property, or the environment.
Carbon Monoxide Gas
The engine exhaust from this vehicle contains carbon monoxide, a colorless,
odorless, and highly toxic gas. As long as you properly maintain your vehicle and
follow the instructions set forth below, you will not accumulate dangerous levels
of carbon monoxide gas in the vehicle interior.
Have the exhaust system inspected for leaks whenever:
• The exhaust system is making an unusual noise.
• The exhaust system may have been damaged.
• The vehicle is raised for an oil change.
When you operate a vehicle with the tailgate open, airflow can pull exhaust gas
into the interior and create a hazardous condition. If you must drive with the
tailgate open, open all the windows and set the climate control system as shown
below.
1. Select the fresh air mode.
2. Select the
3. Set the fan speed to high.
4. Set the temperature control to a comfortable setting.
Adjust the climate control system in the same manner if you sit in your parked
vehicle with the engine running.
mode.
WARNING
Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and
even kill you.
Avoid any enclosed areas or activities that expose you to carbon monoxide.
An enclosed area such as a garage can quickly fill up with carbon monoxide gas.
Do not run the engine with the garage door closed. Even when the garage door is
open, drive out of the garage immediately after starting the engine.
Seat Belts
A seat belt is your best protection in all types of collisions. Airbags are designed to
supplement seat belts, not replace them. So even though your vehicle is equipped
with airbags, make sure you and your passengers always wear your seat belts and
wear them properly.
Lap/Shoulder Seat Belts
All seven or eight seating positions are equipped with lap/shoulder seat belts with
emergency locking retractors. In normal driving, the retractor lets you move freely
while keeping some tension on the belt. During a collision or sudden stop, the
retractor locks to restrain your body. The second- and third-row passenger’s seat
belts also have a lockable retractor for use with child seats.
The front seats are equipped with automatic seat belt tensioners to enhance
safety. The tensioners automatically tighten the front seat belts during a moderate
to severe frontal collision, sometimes even if the collision is not severe enough to
inflate the front airbags.
Proper Use of Seat Belts
Follow these guidelines for proper use:
• All occupants should sit upright, well back in the seat, and remain in that
position for the duration of the trip. Slouching and leaning reduces the
effectiveness of the belt and can increase the chance of serious injury in a
crash.
• Never place the shoulder part of a lap/shoulder seat belt under your arm or
behind your back. This could cause very serious injuries in a crash.
• Two people should never use the same seat belt. If they do, they could be very
seriously injured in a crash.
• Do not put any accessories on the seat belts. Devices intended to improve
comfort or reposition the shoulder part of a seat belt can reduce the protective
capability and increase the chance of serious injury in a crash.
• Regularly check the condition of your seat belts. Check for frays, cuts, burns,
and wear, and that the latches work smoothly and the belts retract easily.
• No one should sit in a seat with an inoperative seat belt or one that does not
appear to be working correctly. Using a seat belt that is not working properly
may not protect the occupant in a crash. Have a dealer check the belt as soon
as possible.
WARNING
Not wearing a seat belt properly increases the chance of a serious injury or
death in a crash, even though your vehicle has airbags.
Be sure you and your passengers always wear seat belts and wear them
properly.
4 || 5
SAFETYSAFETY
Seat Belt Inspection
Regularly check the condition of your seat belts as follows:
• Pull each belt out fully, and look for frays, cuts, burns, and wear.
• Check that the latch plates and buckles work smoothly and the belts retract
easily. If a belt does not retract easily, cleaning the belt may correct the
problem. Use only mild soap and warm water. Do not use bleach or cleaning
solvents. Make sure the belt is completely dry before allowing it to retract.
Any belt that is not in good condition or working properly will not provide proper
protection and should be replaced as soon as possible.
A belt that has been worn during a crash may not provide the same level of
protection in a subsequent crash. Have your seat belts inspected by a dealer after
any collision.
WARNING
Not checking or maintaining seat belts can result in serious injury or death if
the seat belts do not work properly when needed.
Check your seat belts regularly and have any problem corrected as soon as
possible.
Fastening a Seat Belt
Adjust your seat to the proper position (see page 44), and then follow the below
steps.
1. Pull the seat belt out slowly.
2. Insert the latch plate into the buckle, then tug
Pull out
slowly.
on the belt to make sure the buckle is secure.
Make sure that the belt is not twisted or caught
on anything.
3. Position the lap part of the belt as low as possible
across your hips, then pull up on the shoulder
part of the belt so the lap part fits snugly. This lets
Latch
plate
your strong pelvic bones take the force of a crash
and reduces the chance of internal injuries.
4. If necessary, pull up on the belt again to remove
Buckle
any slack, then make sure that the belt rests
across the center of your chest and over your
shoulder. This spreads the forces of a crash over
the strongest bones in your upper body.
Lap belt
as low as
possible.
To release the belt, push the red PRESS button
then guide the belt by hand until it has retracted
completely.
WARNING
Improperly positioning the seat belts can cause serious injury or death in a
crash.
Make sure all seat belts are properly positioned before driving.
Adjusting the Shoulder Anchor
The front seats have adjustable shoulder anchors to accommodate taller and
shorter occupants.
1. Move the anchor up and down while holding the
release button.
2. Position the anchor so that the belt rests across
the center of your chest and over your shoulder.
6 || 7
Push
SAFETYSAFETY
Seat Belt with Detachable Anchor
The seat belts for the second-row and third-row center seat is located in the
ceiling.
1. Pull out the seat belt’s small latch plate and
Small latch plate
the latch plate from each holding slot in the
ceiling.
Latch plate
2. Line up the triangle marks on the small latch plate
and anchor buckle. Make sure the seat belt is not
Small latch plate
twisted. Attach the belt to the anchor buckle.
Anchor buckle
3. Insert the latch plate into the buckle. Properly
fasten the seat belt the same way you fasten
Second-row seat*
Latch plate
the lap/shoulder seat belt.
To unlatch the detachable anchor, insert
the latchplate into the slot on the side of the
Latch plate
anchor buckle.
Small latch plate
WARNING
Using the seat belt with the detachable anchor unlatched increases the
chance of serious injury or death in a crash.
Before using the seat belt, make sure the detachable anchor is correctly
latched.
Buckle
Airbags
Your vehicle is equipped with three types of airbags: front airbags, side airbags, and
side curtain airbags.
Front Airbags (SRS)
The front SRS airbags inflate in a moderate-to-severe frontal collision to help
protect the head and chest of the driver and/or front passenger. They are housed
in the center of the steering wheel for the driver, and in the dashboard for the front
passenger. Both airbags are marked SRS AIRBAG.
SRS (Supplemental Restraint System) indicates that the airbags are designed to
supplement seat belts, not replace them. Seat belts are the occupant’s primary
restraint system.
Advanced Airbags
The front airbags have advanced features to help reduce the likelihood of airbagrelated injuries to smaller occupants.
The driver’s advanced airbag system includes a
seat position sensor. Based on information from this
sensor and the severity of the impact, the advanced
airbag system determines the optimal deployment of
the driver’s airbag.
The front passenger’s advanced airbag system has
weight sensors. We advise against allowing a child
age 12 or under to ride in the front passenger’s
seat. However, if you do allow a child age 12 or
under to ride in the front passenger’s seat, note
that the system will automatically turn off the front
passenger’s airbag if the sensors detect that the
child is approximately 65 lbs (29kg) or less.
Passenger’s
seat
weight
sensors
For the advanced airbags to work properly:
• Do not spill any liquid on or under the seats.
• Do not put any object under the passenger’s seat.
• Make sure any objects are positioned properly on the floor. Improperly
positioned objects can interfere with the advanced airbag sensors.
• All occupants should sit upright and wear their seat belts properly.
• Do not cover the passenger’s side dashboard with a cloth, towel, cover, etc.
• Make sure the floor mat behind the front passenger’s seat is hooked to the
floormat anchor. An improperly placed mat can interfere with the advanced
airbag sensors.
Driver’s
seat
position
sensor
*if equipped
8 || 9
SAFETYSAFETY
Side Airbags
The side airbags help protect the torso and pelvis of the driver or a front
passenger during a moderate-to-severe side impact. They are housed in the
outside edge of the driver’s and front passenger’s seat-backs. Both are marked
SIDE AIRBAG.
Side Curtain Airbags
Side curtain airbags help protect the heads of the driver and passengers in outer
seating positions during a moderate-to-severe side impact. The side curtain
airbags equipped in this vehicle are also designed to help reduce the likelihood
of partial and complete ejection of vehicle occupants through side windows in
crashes, particularly rollover crashes.
The side curtain airbags are located in the ceiling
above the side windows on both sides of the
vehicle.
The side curtain airbags are designed to deploy
in a rollover or moderate-to-severe side impact.
If the SRS control unit senses that your vehicle is
Side curtain airbag storage
about to roll over, it immediately deploys both side
curtain airbags and activates both front seat belt
tensioners. The airbag on the passenger’s side will
deploy, even if there are no passengers on that side
of the vehicle.
To get the best protection from the side curtain
Deployed side curtain airbag
airbags, occupants should wear their seat belts
properly and sit upright and well back in their seats.
When side curtain airbags deploy in a frontal collision
One or both side curtain airbags may inflate in a moderate-to-severe angled
frontal collision. In this case, the side curtain airbags will deploy slightly after the
front airbags.
Important Facts About Your Airbags
Always wear your seat belt properly, and sit upright and as far back from the
steering wheel as possible while allowing full control of the vehicle. A front
passenger should move their seat as far back from the dashboard as possible.
Do not place hard or sharp objects between yourself and a front airbag. Carrying
hard or sharp objects on your lap, or driving with a pipe or other sharp object in
your mouth, can result in injuries if your front airbag inflates.
Do not attach or place objects on the front airbag covers. Objects on the covers
marked SRS AIRBAG could interfere with the proper operation of the airbags or be
propelled inside the vehicle and hurt someone if the airbags inflate.
Do not attach accessories on or near the side airbags. They can interfere with the
proper operation of the airbags, or hurt someone if an airbag inflates.
Do not attach any objects to the side windows or roof pillars. They can interfere
with the proper operation of the side curtain airbags.
Do not cover or replace the front seat-back covers. This can prevent your side
airbags from properly deploying during a side impact.
WARNING
An open glove box can cause serious injury to your passenger in a crash,
even if the passenger is wearing the seat belt.
Always keep the glove box closed while driving.
Airbag System Indicators
If a problem occurs in the airbag system, the SRS indicator comes on and a
message appears on the multi-information display.
SRS (Supplemental Restraint System) indicator
If the indicator comes on at any other time besides
vehicle start-up, or does not come on at all, have the
system checked by a dealer as soon as possible. If
you don’t, your airbags and seat belt tensioners may
not work properly when they are needed.
WARNING
Ignoring the SRS indicator can result in serious injury or death if the airbag
systems or tensioners do not work properly.
Have your vehicle checked by a dealer as soon as possible if the SRS
indicator alerts you to a possible problem.
10 || 11
SAFETYSAFETY
12
6
79108
8
8
8
11
8
Passenger Airbag Off indicator
U.S. Canada
Airbag System Components
The indicator comes on to alert you that the front
passenger’s front airbag has been turned off. This
occurs when the front passenger’s weight sensors
detect 65 lbs (29 kg) or less, the weight of an infant
or small child, on the seat.
Infants and small children should always ride properly restrained in a back seat.
Objects placed on the seat can also cause the indicator to come on.
If the front passenger‘s seat is empty, the passenger’s front airbag will not deploy
and the indicator will not come on.
If the indicator comes on with no occupant or objects in the front passenger’s
seat, something may be interfering with the weight sensors, such as:
• An object hanging on the seat or in the seat-back pocket.
• A child seat or other object pressing against the rear of the seat-back.
• A rear passenger pushing or pulling on the back of the front passenger’s seat.
• The front seat or seat-back is forced against an object on the seat or floor
behind it.
• An object placed under the front passenger’s seat.
If none of these conditions exist, have your vehicle checked by a dealer as soon
as possible.
The passenger airbag off indicator may go on and off repeatedly if the total weight
on the seat is near the airbag cutoff threshold.
1
Two SRS (Supplemental Restraint
System) front airbags. The driver’s
airbag is stored in the center
of the steering wheel; the front
passenger’s airbag is stored in the
dashboard. Both are marked SRS
AIRBAG.
2
Two side airbags, one for the driver
and one for the front passenger.
The airbags are stored in the outer
edges of the seat-backs. Both are
marked SIDE AIRBAG.
3
Two side curtain airbags, one
for each side of the vehicle. The
airbags are stored in the ceiling,
above the side windows. The front
and rear pillars are marked SIDE
CURTAIN AIRBAG.
4
An electronic control unit that,
when the vehicle is on, continually
monitors information about the
various impact sensors, seat
and buckle sensors, rollover
sensor, airbag activators, seat
belt tensioners, and other vehicle
information. During a crash
event the unit can record such
information.
5
Automatic front seat belt
tensioners. The driver’s and front
passenger’s seat belts incorporate
sensors that detect whether or not
they are fastened.
6
A driver’s seat position sensor. If the
seat is too far forward, the airbag
will inflate with less force.
7
Weight sensors in the front
passenger’s seat. The front
passenger’s airbag will be turned off
if the weight on the seat is 65 lbs (29
kg) or less (the weight of an infant or
small child).
8
Impact sensors that can detect a
moderate-to-severe front or side
impact.
9
An indicator on the dashboard that
alerts you that the front passenger’s
front airbag has been turned off.
10
An indicator on the instrument panel
that alerts you to a possible problem
with the airbag system or seat belt
tensioners.
11
Safing sensor
12
A rollover sensor that can detect if
your vehicle is about to roll over and
signal the control unit to deploy both
side curtain airbags.
12 || 13
SAFETYSAFETY
Airbag Care
You do not need to, and should not, perform any maintenance on or replace any
airbag system components yourself. However, you should have your vehicle
inspected by a dealer in the following situations:
When the airbags have deployed
If an airbag has inflated, the control unit and other related parts must be replaced.
Similarly, once an automatic seat belt tensioner has been activated, it must be
replaced.
When the vehicle has been in a moderate-to-severe collision
Even if the airbags did not inflate, have your dealer inspect the following: the
driver’s seat position sensor, weight sensors in the passenger’s seat, front seat
belt tensioners, and each seat belt that was worn during the crash.
Do not remove or modify a front seat without first consulting a dealer
This would likely disable the driver’s seat position sensor or the weight sensors
in the passenger’s seat. If it is necessary to remove or modify a front seat to
accommodate a person with disabilities, contact a Honda dealer. For U.S.
vehicles, call Honda Automobile Customer Service at (800) 999-1009. For Canadian
vehicles, call Honda Canada Customer Relations at (888) 946-6329.
Child Safety
Each year, many children are injured or killed in vehicle crashes because they are
either unrestrained or not properly restrained. In fact, vehicle collisions are the
number one cause of death of children ages 12 and under.
The National Highway Traffic Safety Administration and Transport Canada
recommend that all children ages 12 and under be properly restrained in a rear seat.
Some states or provinces/territories have laws restricting where children may ride.
To reduce the number of child deaths and injuries, every state, Canadian province
and territory requires that infants and children be properly restrained when they ride
in a vehicle.
Protecting Child Passengers
• An inflating front or side airbag can injure or kill a child sitting in the front seat.
• A child in the front seat is more likely to interfere with the driver’s ability to
safely control the vehicle.
• Statistics show that children of all sizes and ages are safer when they are
properly restrained in a rear seat.
• Any child who is too small to wear a seat belt correctly must be restrained in an
approved child seat that is properly secured to the vehicle using either the lap
belt portion of the lap/shoulder belt or the lower anchors of the LATCH system.
• Never hold a child on your lap because it is impossible to protect them in the
event of a collision.
• Never put a seat belt over yourself and a child. During a crash, the belt would
likely press deep into the child and cause serious or fatal injuries.
• Never let two children use the same seat belt. Both children could be very
seriously injured in a crash.
• Do not allow children to operate the doors, windows, or seat adjustments.
• Do not leave children in the vehicle unattended, especially in hot weather when
the inside of the vehicle can get hot enough to kill them. They could also activate
vehicle controls, causing it to move unexpectedly.
WARNING
Children who are unrestrained or improperly restrained can be seriously
injured or killed in a crash.
Any child too small for a seat belt should be properly restrained in a child
seat. A larger child should be properly restrained with a seat belt, using a
booster seat if necessary.
14 || 15
SAFETYSAFETY
WARNING
Allowing a child to play with a seat belt or wrap one around their neck can
result in serious injury or death.
Instruct children not to play with any seat belt and make sure any unused seat
belt a child can reach is buckled, fully retracted, and locked.
Protecting Infants
An infant must be properly restrained in a rear-facing, reclining child seat until the
infant reaches the seat manufacturer’s weight or height limit for the seat, and the
infant is at least one year old. Many experts recommend use of a rear-facing seat
for a child up to two years old if the child’s height and weight are appropriate for a
rear-facing seat.
Child seats must be placed and secured in a rear
seating position. Rear-facing child seats should
never be installed in a forward-facing position.
When properly installed, a rear-facing child seat may prevent the driver or a front
passenger from moving their seat all the way back, or from locking their seat-back
in the desired position. If this occurs, we recommend that you install the child
seat directly behind the front passenger’s seat, move the seat as far forward as
needed, and leave it unoccupied. Or, you may wish to get a smaller rear-facing
child seat.
WARNING
Placing a rear-facing child seat in the front seat can result in serious injury or
death during a crash.
Always place a rear-facing child seat in the rear seat, not the front.
Protecting Smaller Children
If a child is at least one year old and within the weight range indicated by the child
seat manufacturer, the child should be properly restrained in a firmly secured
forward-facing child seat.
We strongly recommend placing a forward-facing
child seat in a rear seating position.
Placing a forward-facing child seat in the front seat
can be hazardous, even with advanced front airbags
that automatically turn the passenger’s front airbag
off. A rear seat is the safest place for a child.
WARNING
Placing a forward-facing child seat in the front seat can result in serious
injury or death if the front airbag inflates.
If you must place a forward-facing child seat in front, move the vehicle seat
as far back as possible, and properly restrain the child.
Selecting a Child Seat
Most child seats are LATCH-compatible (Lower Anchors and Tethers for CHildren).
Some have a rigid-type connector, while others have a flexible-type connector.
Both are equally easy to use. Some existing and previously owned child seats can
only be installed using the seat belt. Whichever type you choose, follow the child
seat manufacturer’s use and care instructions as well as the instructions in this
manual. Proper installation is key to maximizing your child’s safety.
In seating positions and vehicles not equipped with LATCH, a LATCH-compatible
child seat can be installed using the seat belt and a top tether for added security.
This is because all child seats are required to be designed so that they can be
secured with a lap belt or the lap part of a lap/shoulder belt. In addition, the
child seat manufacturer may advise that a seat belt be used to attach a LATCHcompatible seat once a child reaches a specified weight. Please read the child
seat owner’s manual for proper installation instructions.
Important considerations when selecting a child seat
Make sure the child seat meets the following three requirements:
• The child seat is the correct type and size for the child.
• The child seat is the correct type for the seating position.
• The child seat is compliant with Federal Motor Vehicle Safety Standard 213 or
Canadian Motor Vehicle Safety Standard 213.
16 || 17
SAFETYSAFETY
Second-row captain seat
Third row seat
Second-row bench seat
Second-row bench seat
Second-row captain seat
Third row seat
Installing a LATCH-Compatible Child Seat
A LATCH-compatible child seat can be installed in each of the second- and one of
the third-row seats. A child seat is attached to the lower anchors with either the
rigid or flexible type of connectors.
1. Locate the lower anchors under the marks.
Marks
Marks
Marks
3. For second-row outer seats: Raise the outer
head restraint to its highest position, then route
Tether strap hook
the tether strap between the head restraint legs,
and secure the tether strap hook onto the anchor.
Make sure the strap is not twisted.
For the center seat: Lower the center head
restraint to its lowest position, then route the
Anchor
tether strap over the top of the head restraint,
and secure the tether strap hook onto the anchor.
Tether strap hook
Make sure the strap is not twisted.
For third-row outer seat: Route the tether strap
hook between the head restraint legs, and secure
the tether strap hook onto the anchor. Make sure
Anchor
the strap is not twisted.
4. Tighten the tether strap according to the seat
Tether strap hook
maker’s instructions.
5. Make sure the child seat is firmly secured by
rocking it forward and back and side to side; little
Anchor
movement should be felt.
6. Make sure any unused seat belt that a child can reach is buckled, the lockable
retractor is activated, and the belt is fully retracted and locked.
2. Place the child seat on the vehicle seat, then
Lower anchors
attach the child seat to the lower anchors
according to the instructions that came with the
child seat. Make sure that the lower anchors
are not obstructed by the seat belt or any other
object.
18 || 19
Rigid type
Flexible type
SAFETYSAFETY
Second-row bench seat
Second-row captain seat
Second-row bench seat
Third row seat
Second-row captain seat
Third row seat
Installing a Child Seat with a Lap/Shoulder Seat Belt
1. Place the child seat on the vehicle seat.
2. Route the seat belt through the child seat
according to the seat manufacturer’s
instructions, and insert the latch plate into the
buckle. Insert the latch plate fully until it clicks.
3. Slowly pull the shoulder part of the belt all the
way out until it stops. This activates the lockable
retractor.
4. Let the seat belt completely wind up into the
retractor, then try to pull it out to make sure the
retractor is locked. If you are able to pull the
shoulder belt out, the lockable retractor is not
activated. Pull the seat belt all the way out, and
repeat steps 3 – 4.
5. Grab the shoulder part of the seat belt near the
buckle, and pull up to remove any slack from
the lap part of the belt. When doing this, place
your weight on the child seat and push it into the
vehicle seat.
6. Make sure the child seat is firmly secured by
rocking it forward and back and side to side; little
movement should be felt.
7. Make sure any unused seat belt that a child
can reach is buckled, the lockable retractor
is activated, and the belt is fully retracted and
locked.
To deactivate a lockable retractor, release the buckle and allow the seat belt to
wind up all the way.
Adding Security with a Tether
A tether anchorage point is provided behind each second- and third-row seating
position. If you have a child restraint system that comes with a tether but can be
installed with a seat belt, the tether may be used for additional security.
Using a second-row anchor
1. For outer positions: Raise the outer head
Tether anchorage points
restraint to its highest position, then route the
tether strap between the head restraint legs, and
secure the tether strap hook onto the anchor.
Make sure the strap is not twisted.
For the center position: Lower the center head
restraint to its lowest position, then route the
tether strap over the top of the head restraint,
Tether anchorage points
and secure the tether strap hook onto the anchor.
Make sure the strap is not twisted.
2. Tighten the tether strap as instructed by the child
seat manufacturer.
Tether anchorage points
Using a third-row anchor
1. Route the tether strap hook between the head
restraint legs, and secure the tether strap hook
onto the anchor. Make sure the strap is not
twisted.
Tether strap hook
2. Secure the tether strap hook onto the anchor.
3. Tighten the tether strap as instructed by the child
seat manufacturer.
Anchor
Tether strap hook
Anchor
20 || 21
Anchor
Tether strap hook
SAFETYSAFETY
Sun visor
U.S. models
Canadian models
Radiator cap
U.S. models
U.S. models only
Dashboard
Canadian models
Doorjambs
Air conditioner system
Sun visor
U.S. models only
Protecting Larger Children
When a child is too big for a child seat, secure the child in a rear seat using the
lap/shoulder seat belt.
Have the child sit upright and all the way back, then ensure the following:
• The child’s knees bend comfortably over the edge
of the seat.
• The shoulder belt crosses between the child’s
neck and arm.
• The lap part of the seat belt is as low as possible,
touching the child’s thighs.
• The child can stay seated for the whole trip.
If a lap/shoulder belt cannot be used properly, position the child in a booster seat
in a rear seating position. For the child’s safety, check that the child meets the
booster seat manufacturer’s recommendations.
Some U.S. states and Canadian provinces/territories require children to use a
booster seat until they reach a given age or weight (e.g., 6 years or 60 lbs). Be sure
to check current laws in the state or province/territory where you intend to drive.
WARNING
Allowing a child age 12 or under to sit in the front can result in injury or death
if the passenger’s front airbag inflates.
If a larger child must ride in front, move the vehicle seat as far to the rear as
possible, then have the child sit up properly and wear the seat belt properly,
using a booster seat if needed.
Safety Label Locations
Safety labels are in the locations shown. They warn you of potential hazards that
can cause serious injury or death. Read these labels carefully.
Reporting Safety Defects
In the U.S.
If you believe that your vehicle has a defect which could cause a crash or could
cause injury or death, you should immediately inform the National Highway Traffic
Safety Administration (NHTSA) in addition to notifying American Honda Motor Co.,
Inc.
If NHTSA receives similar complaints, it may open an investigation, and if it finds
that a safety defect exists in a group of vehicles, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in individual problems
between you, your dealer, or American Honda Motor Co., Inc.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-3274236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator,
NHTSA, 1200 New Jersey Avenue, SE., Washington, DC 20590. You can also obtain
other information about motor vehicle safety from http://www.safercar.gov.
In Canada
If you believe that your vehicle has a defect which could cause a crash or could
cause injury or death, you should immediately inform Honda Canada, Inc., and you
may also inform Transport Canada.
If Transport Canada receives similar complaints, it may open an investigation, and if
it finds that a safety defect exists in a group of vehicles, it may lead to a recall and
remedy campaign. However, Transport Canada cannot become involved in individual
problems between you, your dealer, or Honda Canada, Inc.
To contact Transport Canada’s Defect Investigations and Recalls Division, you may
call 1-800-333-0510. For more information on reporting safety defects or about motor
vehicle safety, go to http://www.tc.gc.ca/roadsafety.
22 || 23
INSTRUMENT PANELINSTRUMENT PANEL
Canada
INSTRUMENT PANEL
Learn about the indicators and displays related to driving the vehicle.
Indicators briefly appear with each engine start and then go out. Red and amber
indicators are most critical. Blue and green indicators are used for general
information.
Malfunction Indicators
These are the most critical indicators. If they come on and stay lit while driving or at
any other time, there may be a problem. See your dealer if necessary.
Brake system
U.S.
The brake fluid is low, or the brake system has a problem. Press the brake
pedal lightly to check pedal pressure. If normal, check the brake fluid level
Canada
when you stop. If abnormal, take immediate action. If necessary, downshift
the transmission to slow the vehicle using engine braking. Have your vehicle
repaired immediately.
Low oil pressure
Engine oil pressure is low. Stop in a safe place. Open the hood. Check the oil
level, and add oil if necessary (see page 152). If the indicator does not turn
off, have your vehicle repaired immediately.
Charging system
The battery is not charging. Turn off all electrical items, but do not turn off
the vehicle to prevent further battery discharge. Have your vehicle repaired
immediately.
Supplemental Restraint System (SRS)
There is a problem with one of the airbag systems or seat belt tensioners.
Smart Entry system*
There is a problem with the smart entry system.
Malfunction indicator lamp (check engine light)
The emissions control system may have a problem. Avoid high speeds. Have
your vehicle repaired immediately. If the indicator blinks, a misfire in the
engine’s cylinders is detected. Stop in a safe place and wait for the engine
to cool down.
Anti-lock Brake System (ABS)
There is a problem with the anti-lock brake system. Your vehicle still has
normal braking ability, but no anti-lock function.
Tire Pressure Monitoring System (TPMS)*
There is a problem with the tire pressure monitoring system, or the vehicle is
fitted with a spare tire.
Vehicle Stability Assist (VSA) system
There is a problem with the VSA or hill start assist system.
Brake system
SYSTEM
U.S.
There is a problem with one of the braking systems.
Collision Mitigation Braking System (CMBS)*
There is a problem with the system, the temperature is too high, or the
camera or sensor is blocked.
Road Departure Mitigation (RDM)*
There is a problem with the system, the temperature is too high, or the
camera is blocked.
Blind spot information (BSI)*
There is a problem with the system or the radar is blocked.
Electric power steering
There is a problem with the system. Stop the vehicle in a safe place, and
restart the engine.
All-Wheel Drive (AWD)*
There is a problem with the system. If the indicator blinks, the differential
temperature is too high. Stop in a safe place and let the engine idle until the
indicator goes off.
Auto idle stop*
If the indicator blinks, there is a problem with the system.
Adaptive Cruise Control (ACC)*
There is a problem with the system.
Lane Keeping Assist System (LKAS)*
There is a problem with the system.
24 || 25
*if equipped
*if equipped
On/Off Indicators
These indicators remind you when an item is on or off.
INSTRUMENT PANELINSTRUMENT PANEL
Condition Indicators
These indicators may require you to perform an action.
Parking brake
U.S.
Release the parking brake before driving. You will hear a beep if you drive
with it not fully released.
Canada
Seat belt reminder
Make sure seat belts are fastened for you and all passengers. The indicator
blinks and beeps sound continuously if you or your front passenger has not
fastened your seat belts when you begin driving. If the indicator remains on
after seat belts are fastened, see your dealer.
Low fuel
Refuel as soon as possible. If the indicator blinks, there is a problem with the
fuel gauge. See your dealer.
Low tire pressure
Stop in a safe place, check tire pressures, and inflate tire(s) if necessary.
The indicator also appears if your vehicle is fitted with a spare tire. Have
your regular tire repaired or replaced as soon as possible.
VSA off
VSA engaged (blinks)
CMBS* off
RDM* off
LKAS* on
BSI* off
CRUISE MAIN* on
CRUISE CONTROL* on
ACC* on
Turn signals/hazards on
Fog lights* on
High beams on
Exterior lights on
Auto High Beam System* on
ECON mode on
Auto idle stop* on
Auto idle stop* off
System message
When a condition or malfunction indicator comes on, a message also
appears on the multi-information display. Check the display for more
information.
Immobilizer
Your key or remote transmitter cannot be recognized by the vehicle. If the
indicator blinks, you may not be able to start the engine. Turn the vehicle off,
and then on again. If it continues to blink, there may be a problem with the
system. See your dealer.
*if equipped
26 || 27
VEHICLE CONTROLSINSTRUMENT PANEL
Multi-Information Display (MID)
Consists of several displays that provide you with useful information.
Main display (also shows
odometer, gear position,
and outside temperature*)
Info (p/q) buttons
RESET button
Press the Info (p/q) buttons on the steering wheel to change displays. Press the
RESET button to enter menu selections when applicable.
Main display
Distance, average fuel
economy, range, instant
fuel economy (Trip A)
Distance, average fuel
economy, range, instant
fuel economy (Trip B)
VEHICLE CONTROLS
Learn about the various controls necessary for operating and driving the vehicle.
Using the Remote Transmitter
Lock or unlock the doors and tailgate.
Models without remote engine start
Lock button: Press to lock
the doors and tailgate. Press
again for audible verification.
Models with remote engine start
Engine button: After pressing
the Lock button, press and
hold to remotely start the
engine (see page 110).
Unlock button: Press once
to unlock the driver’s door.
Press again to unlock all
doors and the tailgate.
Tailgate button: Press to
unlock the tailgate.
Panic button: Press to sound
the alarm for 30 seconds.
Press again to cancel.
Power tailgate button:
Press and hold to unlock
and open the power tailgate.
Press again to close it.
Tire pressures
Compass*
Turn-by-turn directions*Engine oil life
NOTICE
Leaving the remote transmitter in the vehicle can result in theft or accidental
movement of the vehicle. Always take the remote transmiter with you whenever
you leave the vehicle unattended.
*if equipped
28 || 29
VEHICLE CONTROLSVEHICLE CONTROLS
Smart Entry System
When you carry the remote transmitter (for example, in a pocket or purse) and it
is outside the vehicle and within range (about 32 inches or 80 cm), you can lock or
unlock the doors and tailgate without handling the transmitter.
Unlocking/Locking the Doors
To unlock: Grab the driver’s door handle when the
vehicle is off to unlock the driver’s door. Grab the
front passenger’s door handle to unlock all doors.
To lock: Press the door lock button on either front
door handle or the tailgate when the vehicle is off.
If the remote transmitter is inside the vehicle, the
doors will not lock.
Door lock button
Lock button
n Customizing Door Lock Settings
Customize the auto door-lock setting to your preference. Begin with the vehicle off.
Models with color audio
1.Apply the parking brake
2.Position the driver's door
To enable auto door lock: close the
driver's door
To disable auto door lock: open the
driver's door
3.Set your preference
a. Push ENGINE START/STOP twice (do not press the brake pedal)
b. Press the lock side of the master door lock switch until you hear a click
(~ 5 sec.)
c. Push ENGINE START/STOP twice (do not press the brake pedal)
Models with Display Audio
See Customized Features, page 58.
30 || 31
VEHICLE CONTROLSVEHICLE CONTROLS
Walk Away Auto Lock
When you walk away from the vehicle while carrying the remote transmitter, the
doors can automatically lock if the following conditions are met:
• The remote transmitter is within a range of 6 feet (2 m).
• All doors and the hood are closed.
• There is not an additional remote transmitter inside the vehicle.
Follow these steps (see diagram):
1. Exit the vehicle, close the door and stay near it.
Listen for a beep. The system is activated.
2. Walk at least 6 feet (2 m) away.
3. Listen for a beep and look for the lights to flash.
w
v
u
The doors lock.
To turn on this feature, follow the steps below:
1. From the HOME screen, select Settings.
2. Select Vehicle. The vehicle must be in Park (P).
3. Select Door/Window Setup.
4. Select Walk Away Auto Lock.
5. Select On.
6. Select BACK to exit the menus.
Tailgate Operation
When all the doors are unlocked, the tailgate is unlocked. See page 33 for power
tailgate operation.
Power Tailgate Operation*
Use these methods to operate the power tailgate.
Power Tailgate Button
The vehicle must be in Park (P) with all doors
unlocked.
Press and hold the power tailgate button on the door
to open the tailgate. Press it again at any time to close
it.
Tailgate Outer Handle
Press the tailgate outer handle. A beep sounds, and
the tailgate opens and lifts automatically.
Power Tailgate Close Button
Press the power tailgate close button to
automatically close the tailgate. Press it again at
any time to reverse the tailgate direction.
Manual Operation
Press and hold the tailgate outer handle until you
hear three beeps. The tailgate unlatches and you
can open it manually.
Tailgate release
button
To open the tailgate, press the tailgate release button
under the tailgate handle. Lift open the tailgate.
WARNING
Closing the power tailgate while anyone is in the path of the tailgate can
cause serious injury.
Make sure everyone is clear before closing the tailgate.
NOTICE
Do not push or pull on the power tailgate when it is being automatically opened
To close the tailgate, grab the inner handle, pull the
tailgate down, and push it closed from the outside.
Tailgate release
button
or closed. Forcibly opening or closing the power tailgate while in operation can
deform the tailgate frame.
Inner handle
*if equipped
32 || 33
*if equipped
VEHICLE CONTROLSVEHICLE CONTROLS
Door Operation
Use several methods to lock or unlock the doors.
Using the Lock Tab
To unlock: When you unlock either front door
using the lock tab, the specific door (driver’s or
passenger’s) unlocks.
To lock: When you lock the door using the lock tab
on the driver’s door, all the other doors and tailgate
lock at the same time. When you lock the door using
the lock tab on the front passenger’s door, only that
door locks.
Using the Front Door Inner Handle
When you pull either front door inner handle, the
door unlocks and opens.
Unlocking and opening the driver’s door from the
inner handle unlocks all the other doors.
Using the Master Door Lock Switch
To unlock: Press the unlock side of the switch to
unlock all doors and the tailgate.
To lock: Press the lock side of the switch to lock all
doors and the tailgate.
Childproof Door Locks
The childproof door locks prevent the rear doors
from being opened from the inside regardless of the
position of the lock tab.
Slide the lever in the rear door to the lock position,
and close the door.
Open the door using the outer door handle.
To lock
To unlock
Master door lock switch
To unlock
Lock tab
To lock
Unlock
Lock
Power Window Operation
The power windows can be opened and closed when the vehicle is on by using the
switches on the doors. The switches on the driver’s side can be used to open and
close all the windows.
Automatic Operation
To open: Push the switch down firmly.
To close: Pull the switch up firmly.
The window opens or closes completely. To stop
On
Off
Power window
lock button
the window at any time, push or pull the switch
again briefly.
Manual Operation
To open: Push the switch down lightly.
To close: Pull the switch up lightly.
Release the switch when the windows reach
the desired position.
Driver’s
window
switch
Rear window
switches
Front passenger’s
window switch
Power Window Lock
Push in the power window lock button so only the driver’s window can be
operated. An indicator appears in the button when window lock is on.
WARNING
Closing a power window on someone’s hands or fingers can cause serious
injury.
Make sure your passengers are away from the windows before closing them.
34 || 35
VEHICLE CONTROLSVEHICLE CONTROLS
Models without
panoramic roof
Models with
panoramic roof
Power Moonroof Operation*
The moonroof can be opened and closed when the vehicle is on by using the switch
on the ceiling.
Automatic Operation
To open: Push the switch back firmly to the second
detent, then release.
To close: Push the switch forward firmly to the
second detent, then release.
The moonroof opens or closes completely. To stop
the moonroof at any time, push the switch briefly.
Manual Operation
To open: Push and hold the switch back lightly to the
first detent until the desired position is reached.
To close: Push and hold the switch forward lightly to
the first detent until the desired position is reached.
Moonroof Tilt
To tilt: Push the center of the switch.
To close: Push the switch forward firmly, then release.
NOTICE
Opening the moonroof in below freezing temperatures or when it is covered with
snow or ice can damage the moonroof panel or motor.
Close
Close
Open
Tilt
Open
Tilt
Panoramic Glass Roof*
The ceiling cover in the second row can be opened and closed to reveal the glass
roof when the vehicle is on by using the switch on the ceiling.
Automatic Operation
To open: Push the switch back firmly, then release.
To close: Push the switch forward firmly, then
release.
Open
The cover opens completely. To stop the cover in
either direction, push the switch briefly.
Close
Manual Operation
To open: Push and hold the switch back lightly until the desired position is
reached.
To close: Push and hold the switch forward lightly until the desired position is
reached.
WARNING
Closing the cover on someone’s hands or fingers can cause serious injury.
Make sure your passengers are away from the cover before closing it.
WARNING
Closing the moonroof on someone’s hands or fingers can cause serious injury.
Make sure your passengers are away from the moonroof before closing it.
*if equipped
36 || 37
*if equipped
VEHICLE CONTROLSVEHICLE CONTROLS
Models without
panoramic roof
Models without
panoramic roof
Models with
panoramic roof
Models with
panoramic roof
Interior and Exterior Lights
Operate interior and exterior lights when the vehicle is on or off.
Brightness Control
Adjust instrument panel brightness when the
vehicle is on.
To brighten: Press the + button.
To dim: Press the - button.
A beep sounds when the brightness reaches
minimum or maximum.
Interior Lights
Change the interior light settings using the switch
on the ceiling.
ON position: Interior lights remain on.
Door-activated position: Interior lights come on
when any of the doors are opened, the driver’s door
is unlocked, or the vehicle is turned off.
OFF position: Interior lights remain off.
- button
Door-activated position
Off
+ button
Door-activated position
Off
On
On
Cargo Area Lights
Located on the rear ceiling in front of the tailgate.
ON position: Cargo lights remain on.
Door-activated position: Cargo lights turn on when
Dooractivated
Off
position
On
the tailgate is opened.
OFF position: Cargo area lights remain off.
Exterior Lights
Rotate the switches on the headlight lever to operate the exterior lights. Push the
lever forward to turn on the high beams. Return the lever to its original position for
low beams.
OFF: All exterior lights are off.
High beams
: Turn on exterior lights except headlights.
AUTO: Turn on the automatic lighting feature.
Headlights turn on or off depending on ambient
brightness when the vehicle is on. Headlights
automatically come on after the wipers are
engaged for a certain time.
Low
beams
Flash high
beams
Fog
lights*
: Turn on all exterior lights including headlights.
: Turn fog lights* on or off.
One-Touch Turn Signal
Map Lights
Press the front map lights to turn on or off.
There are also map lights located on the ceiling for
the second- and third-row seats. Turn them on or
off when the front interior light switch is in the dooractivated position.
38 || 39
Use this quick and convenient method to signal a lane change.
Lightly push the turn signal lever up or down for a
three-blink sequence.
Right turn
For a continuous signal, push the lever up or down
until it locks into place.
Left turn
*if equipped
VEHICLE CONTROLSVEHICLE CONTROLS
Auto High Beam System*
Automatically changes the low beam headlights to high beam headlights when
necessary.
How It Works
When you are driving at night above 25 mph (40 km/h) and the headlight lever is
in the low beam position with the switch rotated to AUTO, the system changes
between low and high beams depending on the brightness of the vehicle lights
ahead of you.
Oncoming
vehicle
Vehicle ahead
of you
Your vehicle
If a vehicle is detected ahead of you, the headlights stay in low beams. If the
system does not detect any vehicles ahead of you, the headlights change to high
beams.
Certain conditions, such as weather and brightness of other vehicles’ lights, can
affect system operation.
Turning the System On or Off
Make sure the headlight lever is in the low beam
position with the switch rotated to the AUTO
position. The auto high-beam system indicator
appears when the system is on.
The system is canceled temporarily when you
continuously drive at speeds below 25 mph (40
km/h), the vehicle speed is below 15 mph (24 km/h),
or the windshield wipers run at high speed for more
than a few seconds.
To disable the system: When the vehicle is on and parked, pull the headlight lever
towards you and hold it for 40 seconds. The auto high-beam indicator blinks twice.
To re-enable the system: When the vehicle is on and parked, pull the headlight
lever towards you and hold it for 30 seconds. The auto high-beam indicator blinks
once.
Headlight
switch
To temporarily cancel operation, do either of the following:
• Flash the high beams by moving the lever toward you. Flash the high beams
again to resume auto high beam operation.
• Engage high beams by moving the lever into the high beam position. Return the
lever to the low beam position to resume auto high beam operation.
• If you find the timing of beam changes inconvenient for driving, change the
beams manually.
For the system to work properly:
• Do not place an object that reflects light on the dashboard.
• Keep the windshield around the camera clean. When cleaning the windshield,
be careful not to apply windshield cleanser to the camera lens.
• Do not attach an object, sticker or film in the area around the camera.
• Do not touch the camera lens.
• If the camera receives a strong impact or requires repair, consult a dealer.
If the Cannot Operate message appears, park
your vehicle in a safe place. Wipe away debris
blocking the windshield, then start driving again.
If the message remains on even after driving for a
while with the clean windshield, have your vehicle
checked by a dealer.
*if equipped
40 || 41
VEHICLE CONTROLSVEHICLE CONTROLS
Wiper Operation
The windshield wipers and washers can be used when the vehicle is on.
Front Wipers
Move the wiper lever up or down to the desired position.
When the headlights are in the AUTO position, they automatically turn on when
the front wipers operate several times within a certain interval. The headlights
turn off shortly after the wipers are turned off, or if there is enough ambient light.
Intermittent (INT) Wipers*
1
When you move the lever to the INT position, the
wipers operate based on the delay adjustment.
Rotate the adjustment ring to adjust the wiper delay.
Automatic (AUTO) Intermittent Wipers*
When you move the lever to the AUTO position
while driving in rainy weather, the wipers operate
AUTO position
based on the amount of detected rainfall.
Put the lever in the AUTO position only when
driving in rainy weather.
Rotate the adjustment ring to adjust the rainfall
sensor sensitivity.
Rotate the
adjustment ring.
Return the lever to the OFF position when rain
stops.
Low sensitivity:
Heavy rain accumulation
needed for wipers to
sweep.
High sensitivity:
Light rain accumulation
needed for wipers to
sweep.
NOTICE
Always ensure the wiper lever is in the OFF position before entering a car wash to
prevent severe damage to the windshield wiper system.
Rear Wiper
Rotate the end of the wiper lever to operate the
rear wiper.
When you shift to Reverse (R) and the front
wipers are activated, the rear wiper activates
even if the switch is off.
Rotate the
adjustment ring.
Long delay
Short delay
OFF
INT: Intermittent
ON: Continuous wipe
Washer
NOTICE
Do not use the wipers when the windshield is dry. The windshield will get
scratched, or the rubber blades will get damaged.
In cold weather, the blades may freeze to the windshield, becoming stuck.
Operating the wipers in this condition may damage the wipers. Use the defroster
to warm the windshield, or manually clear the windshield of ice and snow before
turning on the wipers.
*1: models without automatic intermittent wipers; *2: models with automatic intermittent wipers
42 || 43
*models with automatic intermittent wipers
VEHICLE CONTROLSVEHICLE CONTROLS
Adjusting the Seats
Make seat adjustments before driving to ensure the best comfort and safety.
Adjusting the Front Seats
Adjust the driver’s seat as far back as possible while
allowing you to maintain full control of the vehicle.
You should be able to sit upright and well back in the
seat, adequately press the pedals without leaning
forward, and grip the steering wheel comfortably.
The passenger’s seat should be adjusted so that it
is as far back from the front airbag in the dashboard
as possible.
The National Highway Traffic Safety Administration and Transport Canada
recommend that drivers allow at least 10 inches (25 cm) between the center of the
steering wheel and the chest.
Front power seats*
Horizontal
position
adjustment
Height
adjustment*
Move back and allow
sufficient space.
Lumbar support
adjustment*
Seat-back
angle
adjustment
Front manual seats*
Height adjustment
(driver seat only)
Pull up or push down the lever
to raise or lower the seat.
Seat-back angle
Horizontal position
adjustment
Pull up on the bar to move the
seat, then release the bar.
adjustment
Pull up the lever to change
the angle of the seat-back.
WARNING
Reclining the seat-back too far can result in serious injury or death in a crash.
Adjust the seat-back to an upright position, and sit well back in the seat.
WARNING
Sitting too close to a front airbag can result in serious injury or death if the
front airbags inflate.
Always sit as far back from the front airbags as possible while maintaining
control of the vehicle.
WARNING
Sitting improperly or out of position can result in serious injury or death in a
crash.
Always sit upright, well back in the seat, with your feet on the floor.
*if equipped
44 || 45
*if equipped
VEHICLE CONTROLSVEHICLE CONTROLS
Adjusting the Head Restraints
Your vehicle is equipped with head restraints in all seating positions. Head
restraints are most effective for protection against whiplash and other rear-impact
crash injuries.
The center of the back of the occupant’s head
should rest against the center of the restraint. The
tops of the occupant’s ears should be level with the
center height of the restraint.
To raise the head restraint: Pull it upward.
To lower the head restraint: Push it down while
pressing the release button.
Front and second-row head restraints
To remove the head restraint: Pull the restraint up
as far as it will go. Then press the release button(s),
and pull the restraint up and out.
To reinstall a head restraint: Insert the legs back
in place, then adjust the head restraint to an
appropriate height while pressing the release
button(s). Pull up on the restraint to make sure it is
locked in position.
Folding down the third-row head restraints
To fold down: Pull the strap.
To return to upright position: Pull up the head and
push rearward until it latches.
Strap
For a head restraint system to work properly:
• Do not hang any items on the head restraints, or from the restraint legs.
• Do not place any object between an occupant and the seat-back.
• Install each restraint in its proper location.
Floor Mats
Position the front and second-row seat floor mats
properly, and anchor them. If they are not properly
positioned, the floor mats can interfere with the front
seat functions.
Do not put additional floor mats on top of the
anchored mats.
Unlock
Lock
WARNING
Improperly positioning head restraints reduces their effectiveness and
increases the likelihood of serious injury in a crash.
Make sure head restraints are in place and positioned properly before driving.
WARNING
Failure to reinstall, or correctly reinstall, the head restraints can result in
severe injury during a crash.
Always replace the head restraints before driving.
46 || 47
VEHICLE CONTROLSVEHICLE CONTROLS
Rear Seats
Adjust second-row seats, access third-row seats, or fold down seats for carrying
cargo.
Adjusting the Second-Row Passenger’s Seats
Seat-back angle adjustment
Horizontal position adjustment
Pull up the bar to move the seat,
then release the bar.
Folding Down the Second-Row Seat
Separately fold down the left and right halves of the second-row seat to make
room for cargo.
1. Store the center seat belt first. Insert the latch
plate into the slot on the side of the anchor
buckle.
2. Retract the seat belt into the holder on the ceiling
(see page 8).
3. Lower the center head restraint to its lowest
position. Put the armrest back into the seat-back.
4. Pull up on the seat-back angle adjustment lever.
To return the seat to the original position, pull up the seat-back in the upright
position until it latches. Reposition the seat belts as necessary.
Pull up the lever to change
the angle.
Lever
Adjusting the Third-Row Passenger’s Seats
Third-Row Seat Access
Using the button*
Press the button on the seat-back or seat cushion
when the vehicle is stopped. The whole seat slides
forward.
Using the lever or strap*
Pull up on the lever or strap. The whole seat slides
forward.
Seat-back angle adjustment
Pull the strap to change the
angle.
Strap
*if equipped
48 || 49
Loading...
+ 63 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.