Navigation Manual
2020 ODYSSEY
NOTICE
3
WARNING
The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd., reserves the right,
however, to discontinue or change specifications or design at any time without notice and without incurring any obligation.
Accessories Precautions
The GPS antenna is located on the roof. Trees, tall buildings, highway overpasses, tunnels, or overhead electrical power wires can easily interrupt or interfere GPS
reception.
Signal noise from devices such as radar detectors, vehicle tracking devices, remote starters, and additional amplifiers can disrupt the navigation system. If you
install any such item, install it away from the navigation display and antenna.
Important Safety Information
Using the navigation system while driving can take your
attention away from the road, causing a crash in which you
could be seriously injured or killed.
Only operate system controls when the conditions permit you
to safely do so.
Avoid focusing on the screen or manually operating the system controls while driving.
Certain on-screen controls are disabled when driving, however most of the voice commands continue to function. Pull to the side of the road if you need to devote
more attention and time to look at the screen or access additional menus.
Route guidance may conflict with street closures, road construction, detours, and out-of-date map data.
The system itself may also have limitations. Verify route information by carefully observing roads, signs, and signals. Always use your own judgment and obey
traffic laws.
System Limitations
2
This vehicle’s navigation display, if so equipped, includes mercury-containing components. Upon removal, please reuse, recycle, or dispose of as hazardous waste.
Clean the screen with a soft, damp cloth. You may use a mild cleaner intended for use on navigation screens.
00X31-THR-8200 2020 Odyssey Navigation Manual NM-10401
P. 106
2 System Setup P. 15
Start-up 16 Voice Control System 17 Personal Information 18 Display Mode Settings 30
Guidance Volume Settings 32 Map and Vehicle 33 Navigation 40 Traffic 48
Location History 49 About 50 Data Reset 51
2 Navigation P. 53
Entering a Destination 54 Calculating the Route 72 Driving to Your Destination 75 Map Operation 82
Changing Your Route 88 Changing Your Destination 94
Contents
Quick Reference Guide
System Setup
Navigation
P. 2
P. 15
P. 53
2 Troubleshooting P. 99
Troubleshooting 100
2 Reference Information P. 105
System Limitations 106 Customer Assistance 108 Legal Information 110
2 Voice Commands P. 117
Voice Commands 118 List of Categories 120
Troubleshooting
Reference Information
Voice Commands
Index
P. 99
P. 105
P. 117
P. 121
Quick Reference Guide
Quick Reference Guide
Store home address
(P18)
Register
1
home address.
Track route
(P75)
Follow your route in real-time with voice guidance.
Store contacts
(P19)
Store locations to use as the destination.
Enter destination
(P54)
Select your destination using several methods.
Select route
(P73)
Set route preferences and select one of the available routes.
Avoid certain areas
(P43)
Set streets and areas to detour around.
Add waypoints
(P90)
Add “pit stops” along your route.
Traffic Information* (P80)
View and avoid congestion and traffic incidents.
*: Available only in certain areas.
Overview—Functions at a Glance
Navigation
You can select any place/landmark as a destination by using the touchscreen. The navigation system gives you
turn-by-turn driving directions to your destination.
2
Quick Reference Guide
HOME Screen
(Home)
Display the HOME screen.
(Back)
Go back to the previous screen.
(Display Mode)
Switch between Day and Night modes manually.
VOL (Volume)
Increase or decrease the audio
volume.
Navigation
Display the navigation feature that was
used the last time.
At start-up, the map screen is displayed.
The system displays various functions from the HOME screen. Press the (Home) icon at any time to return to the main HOME screen.
3
Quick Reference Guide
Touchscreen Operation
You can operate the system using your finger on the touchscreen.
The touchscreen can be operated if you are wearing thin gloves, but it may be more difficult for the system to respond.
Tap
Touch the screen lightly with your finger to select an option on the
screen.
Swipe
Lightly sweep your finger side to side or up and down to scroll a list
or map.
You can change the touchscreen sensitivity setting.
2 Refer to the Owners Manual.
Slide
Move your finger slowly across the screen to scroll the map.
Pinch In/Out
Open or close your fingers on the screen in a pinching motion to
zoom in or out of the map.
4
Quick Reference Guide
On input search screens, the suggested search terms are
displayed. Select Done to display a list of possible entries.
How to Enter Information
You can enter information (e.g. city names, street names, numbers, and symbols) when prompted on the input screen.
Using Voice Commands
When you see in this manual, voice commands are available for
that feature.
The system recognizes only certain commands.
Available navigation commands (P118)
Press the (Talk) button, and say the command, phrase, letter,
number, or symbol (e.g., say “1”).
If a voice command is not recognized, a list is displayed with
possible options.
On list screens:
Say the number of the list item (e.g., say “Three” to select
item 3).
Say “Back” to return to the previous screen.
Say “Next” for next page.
Say “Previous” for previous page.
Say “Cancel” to end the voice command function.
Using the Touchscreen
Select a character or icon on the screen to select it.
Select to remove the last entered character.
Select to remove all entered characters.
Select to display upper/lower case characters.
Select Space to enter a space character.
Select to display other types of characters.
Select to change the keypad language.
5
Quick Reference Guide
Map Screen Legend
Map operation icons
(P82)
Current vehicle position
Streets
Landmark icons
Map scale (P82)
Map tools (P83)
Feature areas
Where To?
(P54)
The color of the map is different depending on the selected Map Theme.
6
Quick Reference Guide
Dashboards (P75)
Next guidance indicator (P75)
Distance to the next guidance point and street name of
next guidance point.
Select to get next voice guidance.
Queue indicator
Where To? (P54)
Calculated route
Speed limit
Current street name
Waypoint
Street name of next
guidance point
Distance to next
guidance point
Estimated time to
next guidance point
Day Mode Night Mode
Remaining
distance
Street name of next
guidance point
Next driving maneuver is
approaching.
During Route Guidance
During route guidance, route information is displayed on the map screen.
You can see the detailed information on the turn list screen.
Map Screen
Guidance Screen
Day or Night Mode
Press the (Display Mode) icon to
manually switch between Day and
Night modes.
Turn-by-Turn Directions
The next guidance point appears on
the Driver Information Interface.
7
Quick Reference Guide
Navigation—Home Addresses and Going Home
The “Home” feature automatically routes you to your home address from any location simply by selecting Go Home.
You can store one home address. (P18)
The order of the steps may change depending on the map data loaded on your system.
Storing Your Home Address
a Press the (Home) icon and then
select Navigation.
b Select .
c Select and then select Set Home
Location.
d Select Enter My Address.
e Enter a house number and street
name.
f Select Done or a suggestion.
g Select an address from the list.
h Select Select.
8
Going Home
a Press the (Home) icon and then
select Navigation.
b Select .
c Select Go Home.
Alternatively, you can say
“Navigation” and then “Go
Home” from any screen.
Quick Reference Guide
Navigation—Entering a Destination
Enter your destination using one of several methods, then follow route guidance on the map to your destination.
The order of the steps may change depending on the map data loaded on your system.
a Press the (Home) icon and then
select Navigation.
b Select .
c Select the search bar.
d Enter the house number and street
name.
e Select Done or a suggestion.
f Select an address from the list.
g Select Go!.
Route guidance to the destination
begins.
Routes: Choose one of multiple routes.
Info: Display the location information
and save a place.
9
Quick Reference Guide
Navigation—Changing Route or Destination
You can alter your route by adding waypoints to visit, or changing your destination during route guidance.
Adding a Waypoint (“Pit Stop”)
You can add waypoints along your route.
(P90)
a Press the (Home) icon and then
select Navigation.
b Select .
c Select a search method.
d Select the location to add to the
destination list and select Go!.
e Select Add as Next Stop or Add to
Active Route.
f If necessary, edit the order of the
destinations.
Changing Your Destination
There are several methods you can use to
specify a new destination during route
guidance.
Searching nearby hospitals, police
stations, gas stations, or tow services
(P95)
Select the vehicle icon and select an
option.
Selecting an icon on the map (P94)
Select a place/landmark icon or a new
area on the map twice.
Entering a new destination (P97)
Select Where To? and then enter a new
destination.
Canceling Your Route
a Select on the map.
b Select Stop.
Alternatively, you can say
“Navigation” and then “Stop
route” from any screen.
10
Quick Reference Guide
Voice Control Operation
Voice Portal Screen
a Press and release the (Talk)
button.
The system beeps when ready for a
command. Press the (Hang-Up)
button to cancel.
b Say “Navigation.”
The Voice Command screen is
displayed.
After that follow the voice prompt
and say a voice command.
The audio system is muted during voice
control mode.
You can use other voice commands on
the Voice Portal screen.
Carefully read the usage note for the
voice control.
Voice Control System (P17)
The system recognizes only certain
commands.
Available navigation commands
(P118)
Voice Command Screen
a After saying “Navigation” from
the Voice Portal screen, the below
screen appears.
b Listen for the voice prompt, then say a
voice command.
You do not need to press the (Talk)
button again in the Voice Command
screen.
Available voice commands are
highlighted on the screen.
11
Quick Reference Guide
Troubleshooting
For more Information
(P99)
Why does the vehicle position icon on the map appear
slightly off my actual position, especially at intersections?
This is normal. The navigation system is unaware of the
width of intersections. Large differences in vehicle position
can indicate a temporary loss of the GPS signal.
Why does the “Arrival time” display sometimes increase
even though I am getting closer to my destination?
The “Arrival time” is based on the speed limit on each
road. Depending on the traffic conditions, the “Arrival
time” may be calculated to be earlier or later.
Why does my clock frequently change the time forward
and backward by one hour?
The clock setting is automatically updated based on your
GPS location. If you are driving near a time zone border,
the automatic update likely is the reason.
How do I turn on the navigation system voice guidance?
●
Press the (Home) icon.
Select Navigation > > Guidance Volume.
Turn up the volume if it is low.
●
Adjust the volume using the volume knob during the
voice guidance.
How do I specify a destination when an entered city or
street could not be found?
Try selecting the destination directly from the map.
12
How to Use This Manual
Searching the Table of Contents
(P1)
First, find the general chapter related to
what you are looking for (e.g., entering
a destination from the Saved Places).
Then, go to that chapter to view a more
specific table of contents.
Searching the Index
(P121)
This more detailed table of contents
shows you exactly what information is
listed by section and title.
The Index consists of
main terms and subentries. The sub-entries
help you get to the
desired page depending
on what you are looking
for.
Table of Contents
Chapter Contents
Navigation Screen
Index
Two types of Tables of Contents help
you find your desired information.
Menu items displayed on the
navigation screen (e.g., Saved) can be
found individually in the Index.
More Detailed
Contents
Go to the
Next Page
This section explains different methods on how you can easily find information in this manual.
13
uuEntering a Destination uSaved
Navigation
Saved
H (Home) u Navigation uuSaved
Select a saved location to use as the destination.
1. Select your destination from the
list.
2. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
Recents
H (Home) u Navigation uuRecents
Select an address from a list of your 50 most recent destinations to use as the
1 Saved
You can add, edit, or delete the saved place.
2 Saved Locations P. 19
Using Voice Command
You can utilize a saved place by using voice
commands.
From the Voice Portal screen, say “Navigation.”
Say “Saved Places” on the voice command
screen, then say a saved place (e.g., “Honda”).
Say “Go” to set the route.
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
1 Recents
Select the item on the system
control panel.
Menu Tree
The menu tree helps guide you
through the system’s menu options.
To get to your desired function, follow
the menu tree in order of the steps
shown.
Select the menu option.
After following the menu
tree, step-by-step
instructions explain how to
achieve the desired result.
* Sample pages and images in this section may differ from the actual ones.
Select Saved.
(Home)
Saved
Navigation
14
System Setup
This section describes the start-up procedure and the navigation and setup functions.
Start-up ....................................................16
Voice Control System ..............................17
Voice Recognition ...................................17
Personal Information...............................18
Setting Home Location............................18
Saved Locations ......................................19
Saved Trips .............................................26
Display Mode Settings ............................30
Switching Display Mode Manually ...........30
Guidance Volume Settings......................32
Map and Vehicle ......................................33
Vehicle Selection.....................................34
Driving Map View (Map Orientation) .......35
Map Theme ............................................36
Map Layer...............................................37
myMaps................................................. 38
Map Updates ......................................... 39
Navigation............................................... 40
Calculation Mode................................... 41
Avoidances ............................................ 42
Custom Avoidances ............................... 43
Satellite Status ....................................... 47
Traffic....................................................... 48
Location History...................................... 49
About....................................................... 50
Data Reset ............................................... 51
Reset Factory Default Settings ................ 51
15
System Setup
Start-up
1 Start-up
Avoid focusing on the screen and drive safely.
When you use the navigation system, the system may
close other apps.
When you select Navigation, the system displays the
navigation feature that was used the last time. At
start-up, the map screen is displayed.
The navigation system starts automatically when you set the power mode to
ACCESSORY or ON. At start-up, the following confirmation screen is displayed.
Limitations for Manual Operation
■
Certain manual functions are disabled or inoperable while the vehicle is in motion.
You cannot select a grayed-out option until the vehicle is stopped.
Voice commands are still operable while the vehicle is in motion.
1. Select OK.
u The HOME screen is displayed.
u If you do not select OK, the
system will automatically select
OK after a certain period of
time.
u The system will automatically
start up the feature that was
last in use.
2. Select Navigation.
u The map screen is displayed.
16
System Setup
Voice Control System
1 Voice Control System
When you press the (Talk) button, the system
prompts you to say a voice command. Press and
release the (Talk) button again to bypass this
prompt and give a command.
1 Voice Recognition
The voice control system can only be used from the
driver’s seat because the microphone unit removes
noises from the front passenger’s side.
Your vehicle has a voice control system that allows hands-free operation of the
navigation system functions.
The voice control system uses the (Talk) and
steering wheel and a microphone near the map lights on the ceiling.
For details of the (Talk) button, (Hang-Up) button and microphone position,
see the Owner's Manual.
Voice Recognition
To achieve optimum voice recognition when using the navigation voice control
system:
• Make sure the correct screen is displayed for the voice command that you are
using. The system recognizes only certain commands.
Available navigation commands:
2 Voice Commands P. 118
• Close the windows and sunroof.
• Adjust the dashboard and side vents so air does not blow onto the microphone
on the ceiling.
• Speak in a clear, natural speaking voice without pausing between words.
• Reduce any background noise if possible. The system may misinterpret your
command if more than one person is speaking at the same time.
(Hang-Up) buttons on the
17
System Setup
Personal Information
1 Personal Information
The home location can be overwritten. Select
Change Home Location in step 1.
Setting Home Location
H (Home) u Navigation uu
Use the personal information menu to set your home location.
The following options are available:
• Enter My Address: Sets the home location by entering the address.
2 Storing Your Home Address P. 8
• Use Current Location: Sets your current location as your home location.
• Recently Found: Sets the home location from a recently found location.
• Saved Place: Sets the home location from a saved place.
1. Select Set Home Location.
2. Select an option.
u Select Use Current Location
to set home location.
u If selecting Enter My Address,
Recently Found or Saved
Place, proceed to steps 3 and 4.
3. Select the home location.
4. Select Select.
18
System Setup
Saved Locations
You can save locations so you can quickly find them and create routes to them.
■
H (Home) u Navigation u
uuPersonal InformationuSaved Locations
Saving a Location
1. Select a search method.
u Find a location that you want to
save.
2 Entering a Destination P. 54
2. Select Info.
3. Select Save.
4. Enter a name and select Done.
Continued
19
uuPersonal Information u Saved Locations
System Setup
Saving a Location Manually
■
H (Home) u Navigation
1. Select a destination from the map.
2 Map Input P. 71
2. Select the destination name at the
bottom of the map.
3. Select Save.
4. Enter the place name and select
Done.
20
System Setup
Saving Your Current Location
1 Saving Your Current Location
Vehicle position may not be displayed when:
•
The vehicle is traveling off-road.
•
The vehicle position data cannot be updated.
■
H (Home) u Navigation
uuPersonal InformationuSaved Locations
1. Select the vehicle icon.
2. Select Save.
3. Enter a name of the location.
4. Select Done.
Continued
21
uuPersonal Information u Saved Locations
System Setup
Editing a Saved Location
■
H (Home) u Navigation uuSaved
1. Select a saved location you want
to edit.
2. Select Info.
3. Select .
4. Select Edit.
22
System Setup
The following options are available:
• Name: Enters a new name for the location.
• Phone Number: Enters a phone number.
• Map Symbol: Select a symbol.
uuPersonal InformationuSaved Locations
5. Select an option.
Continued
23
uuPersonal Information u Saved Locations
System Setup
Deleting a Saved Location
■
H (Home) u Navigation uuSaved
1. Select a saved location you want
to delete.
2. Select Info.
3. Select .
4. Select Delete.
5. Select Delete.
24
System Setup
■
H (Home) u Navigation uuSaved
uuPersonal InformationuSaved Locations
Deleting Saved Locations
1. Select .
2. Select Delete Saved Places.
3. Select a saved location you want
to delete.
u Select Select All to delete all
saved locations.
4. Select Delete.
5. Select Delete.
25
uuPersonal Information u Saved Trips
System Setup
Saved Trips
You can use myTrips feature to create and save a route with multiple destinations.
Creating Your Trip
■
H (Home) u Navigation uumyTrips u Create Trip u Add Starting
Point
1. Select a method to enter a new
destination.
2 Entering a Destination P. 54
2. Select Select if necessary.
3. Select Add Destinations to add
additional locations.
u Repeat steps 1 and 2 to enter
the destination.
u Select and hold , or and
then move the destination to
the desired position.
26
System Setup
Editing a Saved Trip
1 Editing a Saved Trip
The route preference is just for the trip. If you want to
change the route preference for routing, change the
navigation settings.
2 Calculation Mode P. 41
2 Avoidances P. 42
■
H (Home) u Navigation uumyTrips
The following options are available:
• Trip Name: Enters a new name for the saved trip.
• Optimize Order: Automatically orders the waypoints in the destination list.
• Calculation Mode: Changes the route preferences (calculating method).
• Avoidances: Changes preferences for route options to avoid.
uuPersonal InformationuSaved Trips
1. Select a saved trip you want to
edit.
2. Select Trip Settings.
3. Select an option.
Continued
27
uuPersonal Information u Saved Trips
System Setup
■ Reordering Destinations
■ Deleting a Destination
1. Select a trip from myTrips list.
2. Select Edit Destinations.
3. Select and hold , or and
then move the destination to the
desired position.
u Select Add Destinations to
add a new location.
u The route is automatically
recalculated.
1. Select a trip from myTrips list.
2. Select Edit Destinations.
3. Select .
4. Select Remove Destinations.
5. Select the location to delete.
u Select Select All to delete all
destinations.
6. Select Remove.
28
System Setup
■
H (Home) u Navigation uumyTrips
■
H (Home) u Navigation uumyTrips
uuPersonal InformationuSaved Trips
Deleting a Saved Trip
1. Select a trip.
2. Select .
3. Select Delete Trip.
Deleting Saved Trips
1. Select .
2. Select Delete Trips.
3. Select a trip to delete.
u Select Select All to delete all
trips.
4. Select Delete.
29
System Setup
Display Mode Settings
1 Switching Display Mode Manually
You can also adjust the display brightness by sliding
or swiping on the brightness bar.
You can change the touchscreen sensitivity setting.
2 Refer to the Owners Manual.
Switching Display Mode Manually
Set the screen brightness separately for Day and Night modes. Press the
(Display Mode) icon to cycle through the display modes (Day to Night to Off).
Press the (Display Mode) icon.
u The brightness bar is displayed for
a few seconds.
u Select or to adjust the
brightness.
30
uuDisplay Mode Settingsu Switching Display Mode Manually
System Setup
* Not available on all models
Illumination
control
(Display
Mode) icon
Sunlight sensor
*
(see your Owner’s
Manual for
location)
Dash illumination
adjustment knob
(see your Owner’s
Manual for
location)
Headlights (Auto/
On/Off)
Operation
Selects Day or Night display mode when the user
wants to change the brightness of the display
temporarily.
Remember: This icon overrides all other display
brightness adjustments either set automatically by
the sunlight sensor or manually from the System
settings screen.
If the sunlight sensor detects daylight and the
headlights are turned on, the system automatically
overrides the Night display and displays the Day
display mode.
Remember: If desired, use the (Display Mode)
icon to override this automatic choice.
When the headlights are turned on, and you wish to
have the Day display mode, adjust the illumination
to the full brightness (beeps).
Remember: Adjust the dash brightness back to
midrange to allow auto switching by sensing the
headlights are on or off.
When turned on, the display changes to Night
display mode.
The previous three controls listed above can
“cancel” this function.
Remember: Use the (Display Mode) icon, to
adjust the dash illumination to full brightness, or set
the display to your desired choice.
31
System Setup
Guidance Volume Settings
1 Guidance Volume Settings
You can also adjust the volume by sliding or swiping
on the volume bar.
This option is accessible on any screen that includes
the options menu icon.
Select to open the options menu, and then select
Guidance Volume.
During the voice guidance, you can adjust the
guidance volume using the volume knob.
H (Home) u Navigation uuGuidance Volume
Adjust the navigation system volume level.
Select or to adjust the
guidance volume.
u Select Mute to mute the
guidance.
32
System Setup
Map and Vehicle
H (Home) u Navigation uuSettings u Map and Vehicle
Change the map settings.
The following options are available:
• Vehicle Selection: Changes the icon to represent your position on the map.
• Driving Map View: Sets the perspective on the map.
• Map Theme: Changes the color of the map data.
• Map Layer: Sets the data that appears on the map.
• myMaps: View installed maps the system uses.
• Map Updates:View the instructions for map updates.
Select an option.
2 Vehicle Selection P. 34
2 Driving Map View (Map Orientation) P. 35
2 Map Theme P. 36
2 Map Layer P. 37
2 myMaps P. 38
2 Map Updates P. 39
33
uuMap and Vehicleu Vehicle Selection
System Setup
1 Vehicle Selection
The factory default is set to .
Vehicle Selection
H (Home) u Navigation uuSettings u Map and Vehicle u Vehicle
Selection
You can choose your vehicle icon.
1. Select or to choose the
desired icon.
2. Select Save.
34
System Setup
Driving Map View (Map Orientation)
H (Home) u Navigation uuSettings u Map and Vehicle u Driving
Map View
uuMap and VehicleuDriving Map View (Map Orientation)
Select the map orientation.
The following options are available:
• 3D (factory default): Displays the map in 3D with your direction of travel facing
• Track Up: Displays the map with your direction of travel facing upwards.
• North Up: Displays the map with north always pointing up.
1. Select an option.
2. Select Save.
upwards.
35
uuMap and Vehicleu Map Theme
System Setup
Map Theme
H (Home) u Navigation uuSettings u Map and Vehicle u Map
Theme
Changes the color of the map data.
1. Select an option.
2. Select Save.
36
System Setup
Map Layer
1 Map Layer
Off-Road Breadcrumbs is set to off as factory
default.
You can set the categories of places appear along the
road on the map screen.
Select beside Places along the road, select the
categories to show, and then select Save.
H (Home) u Navigation uuSettings u Map and Vehicle u Map
Layer
uuMap and VehicleuMap Layer
Sets the data that appears on the map screen.
1. Select an option(s).
2. Select Save.
37
uuMap and Vehicleu myMaps
System Setup
myMaps
H (Home) u Navigation uuSettings u Map and Vehicle u myMaps
View installed maps the system uses.
Select an item.
38
System Setup
Map Updates
1 Map Updates
For information on navigation updates for your
vehicle, please visit:
•
U.S.: www.hondanavi.navigation.com
•
Canada: www.honda.ca/owners/honda-services/
navigation
2 Obtaining a Navigation Update P. 108
H (Home) u Navigation uuSettings u Map and Vehicle u Map
Updates
uuMap and Vehicleu Map Updates
Check and install map updates.
Follow the on-screen instructions.
39
System Setup
Navigation
1 Navigation
GPS Simulator is set to off as factory default.
You can access the navigation settings from any
screen includes the options menu icon.
Select to open the options menu, and then select
Navigation Settings.
H (Home) u Navigation uuSettings u Navigation
Changes the navigation settings.
The following options are available:
• Calculation Mode: Sets route preference.
2 Calculation Mode P. 41
• Avoidances: Sets road features to avoid on a route.
2 Avoidances P. 42
• Custom Avoidances: Allows you to avoid specific roads or areas.
2 Custom Avoidances P. 43
• Satellite Status: Displays the satellite' status.
2 Satellite Status P. 47
• GPS Simulator: Stops the system from receiving a GPS signal.
40
System Setup
Calculation Mode
H (Home) u Navigation uuSettings u Navigation u Calculation
Mode
uuNavigationu Calculation Mode
Sets the route preference.
The following options are available:
• Faster Time (factory default): Calculates routes that are faster to drive but can be
• Shorter Distance: Calculates routes that are shorter in distance but can take
• Less Fuel: Calculates routes that could use less fuel than other routes.
1. Select an option.
2. Select Save.
longer in distance.
more time to drive.
41
uuNavigationu Avoidances
System Setup
1 Avoidances
Highways, Tolls and Fees, and Ferries are set to off
as factory default.
Avoidances
H (Home) u Navigation uuSettings u Navigation u Avoidances
Set preferences for route options to avoid.
The following options are available:
• U-Turns: Avoids u-turns.
• Highways: Avoids highways.
• Tolls and Fees: Avoids toll roads.
• Ferries: Avoids ferries.
• Carpool Lanes: Avoids car share lanes.
• Unpaved Roads: Avoids unpaved roads.
• Custom Avoidances: Avoids specific areas and roads.
2 Custom Avoidances P. 43
1. Select an option(s).
2. Select Save.
42
System Setup
Custom Avoidances
H (Home) u Navigation uuSettings u Navigation u Custom
Avoidances
uuNavigationu Custom Avoidances
Allows you to avoid specific areas and sections of road. You can enable and disable
custom avoidances as needed.
The following options are available:
• Avoid Area: Sets an area to avoid.
• Avoid Road: Sets a road to avoid.
1. Select Add Avoidance.
2. Select an option.
2 Adding an Avoid Area P. 44
2 Adding an Avoid Road P. 45
Continued
43
uuNavigationu Custom Avoidances
System Setup
Adding an Avoid Area
■
H (Home) u Navigation uuSettings u Navigation u Custom
Avoidances u Add Avoidance u Avoid Area
1. Select the upper-right (left) corner
of the area to avoid. Select Next.
u The icon is displayed on the
map.
2. Select the lower-left (right) corner
of the area to avoid. Select Next.
3. Select Done.
44
System Setup
■
H (Home) u Navigation uuSettings u Navigation u Custom
uuNavigationu Custom Avoidances
Adding an Avoid Road
Avoidances u Add Avoidance u Avoid Road
1. Select the starting point of the
section of road to avoid. Select
Next.
u The icon is displayed on the
map.
2. Select the ending point of the road
section. Select Next.
3. Select Done.
Continued
45
uuNavigationu Custom Avoidances
System Setup
Editing a Custom Avoidance
■
H (Home) u Navigation uuSettings u Navigation u Custom
Avoidances
1. Select the area or road to edit
from the list.
2. Select an item.
The following items are available:
• Enable: Sets whether to enable the avoidance.
• Rename: Enters a new name.
• Delete: Deletes a selected area or road.
46
System Setup
Satellite Status
H (Home) u Navigation uuSettings u Navigation u Satellite
Status
uuNavigation u Satellite Status
View the satellites’ status.
47
System Setup
Traffic
H (Home) u Navigation uuSettings u Traffic
Sets the traffic feature.
The following options are available:
• Traffic: Enables the traffic feature.
2 Traffic Information P. 80
• Traffic Alert: Sets whether to receive an alert when traffic may cause a delay.
• Automatic Route Optimization: Sets whether to use optimized alternate
routes.
• Current Provider: Sets the traffic provider to use for traffic data.
• Subscriptions: Displays the lists of the current traffic subscriptions.
Select an option.
48
System Setup
Location History
H (Home) u Navigation uuSettings u Location History
Set the history data usage or clear the travel data.
The following options are available:
• Travel Data Recording: Allows the system to record your travel data used for
• Predicted Destination Alert: Sets whether the system provides the predicted
• Remove All myTrends Places: Deletes all myTrends places.
• Clear Off-Road Breadcrumbs: Clears off-road breadcrumbs appear on the
Select an option.
predictions.
destination.
2 Predicted Destination P. 70
map.
49
System Setup
About
H (Home) u Navigation uuSettings u About
Select an option.
The following options are available:
• System Information: Displays the system information.
• EULAs: Displays end-user license agreements.
• Copyright and Acknowledgments: Displays copyright and acknowledgments
information.
• Restore Navigation Settings: Restores navigation settings to the factory
defaults.
2 Reset Factory Default Settings P. 51
50
System Setup
Data Reset
1 Reset Factory Default Settings
When you want to reset the following options, see
the below references:
•
Home
2 Deleting Saved Locations P. 25
•
Saved
2 Saved Locations P. 19
•
Recents
2 Recents P. 68
•
myTrips
2 Saved Trips P. 26
When you transfer the vehicle to a third party, reset
all settings to default and delete all personal data.
Reset Factory Default Settings
H (Home) u Navigation uuSettings u About
You can restore all settings to the factory default values.
1. Select Restore Navigation
Settings.
2. Select Restore.
51
52
Navigation
This section describes how to enter a destination, select a route to take, and follow the
route to your destination. It also describes how to change your route or destination along
the way.
Entering a Destination ............................54
Search Tools ...........................................60
Categories ..............................................67
Saved......................................................68
Recents...................................................68
myTrips...................................................69
myTrends................................................70
Map Input...............................................71
Calculating the Route ..............................72
Viewing and Selecting the Routes ...........73
Viewing the Location Information ...........74
Driving to Your Destination ...................75
Viewing the Route ..................................75
Traffic Information ..................................80
Map Operation........................................ 82
Map Tools.............................................. 83
Changing Your Route............................. 88
Stopping the Route ................................ 88
Taking a Detour ..................................... 89
Adding Waypoints ................................. 90
Editing the Route ................................... 91
Changing Your Destination ................... 94
Selecting a Destination on the Map ........ 94
Searching Near Establishment ................ 95
Entering a New Destination.................... 97
53
Navigation
Entering a Destination
1 Entering a Destination
The Display Audio system can only provide route
guidance from one navigation system at a time.
When setting a destination on one system, any active
route guidance with the other system is canceled,
and the system you are currently using will direct you
to your destination.
If you press the (Home) button on the steering
wheel, select Navigation and then press the ENTER
button, the following items are available. Use the
steering wheel buttons to select the items.
•
Go Home
•
Saved
•
Recent
When en route, the following item is available.
•
Cancel Route
(Home) Button
H (Home) u Navigation u
This section describes how to enter a destination for route guidance.
The following options are available:
• Keyword or Address, State: Sets a destination by entering a keyword, address
or state name.
2 Using the Search Bar P. 56
• Searching near: Selects the city to search near.
2 Changing the Search Area P. 57
• Go Home: Sets your home address as the destination.
2 Going Home P. 8
• Search Tools: Sets a destination by searching for a place.
2 Search Tools P. 60
• Categories: Sets a destination by selecting a category.
2 Categories P. 67
• Saved: Sets a destination by selecting a place stored in the Saved list.
2 Saved P. 68
• Recents: Sets a destination by selecting a previous destination.
2 Recents P. 68
• myTrips: Sets a destination by selecting a saved route.
2 myTrips P. 69
Select an option.
54
uuEntering a Destinationu
Navigation
• myTrends: Sets a destination by selecting a place in the list of frequently-visited
destinations.
2 myTrends P. 70
• Add Shortcut: Adds shortcuts to the Where To? menu.
2 Adding Shortcuts P. 58
Continued
55
uuEntering a Destination u
Navigation
1 Using the Search Bar
Using Voice Command
You can say the names of popular, well-known
locations.
From the Voice Portal screen, say “Navigation.”
Say “Find Place,” then say a place name (e.g.,
“Honda”).
Say the line number of screen (e.g., “1”).
Say “Go” to set the route.
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
•
To search for a type of business, enter a category
name, such as “movie theaters.”
•
To search for a business by name, enter all or part
of the name.
•
To search for an address near you, enter the street
number and street name.
•
To search for an address in another city, enter the
street number, street name, city, and state.
•
To search for a city, enter the city and state.
If you want to delete the search history, reset the
navigation settings to default.
2 Reset Factory Default Settings P. 51
You can change the order of search results.
Select and then select Sort POI Results.
Using the Search Bar
■
H (Home) u Navigation uuKeyword or Address, State
You can use the search bar to search for locations by entering a keyword, address,
or state name.
1. Enter a search term.
u The search history is displayed
below the search bar.
u Suggested search terms appear
below the search bar as you
type.
2. Select Done or a suggested search
term.
3. Select your destination from the
list.
4. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
56
uuEntering a Destinationu
Navigation
1 Changing the Search Area
My Active Route and My Destination can be set
when the route is active.
Changing the Search Area
■
H (Home) u Navigation uuSearching near
By default, your system finds locations closest to your current location. You can find
a location near another city or location.
Select an option.
The following options are available:
• My Active Route: Searches along your current route.
• My Destination: Searches near your current destination.
• My Current Location: Searches near your current location.
• A Different City: Searches near the city you select.
• Recent Places: Searches near a recent destination.
• Saved Places: Searches near a saved place.
Continued
57
uuEntering a Destination u
Navigation
Adding Shortcuts
■
H (Home) u Navigation uuAdd Shortcut
Up to 50 shortcut icons can be stored.
Select an option you want to add as
a shortcut.
58
uuEntering a Destinationu
Navigation
Deleting Shortcuts
■
H (Home) u Navigation uuuRemove Shortcut(s)
1. Select a shortcut to delete.
u Select Select All to delete all
shortcuts.
2. Select Remove.
59
uuEntering a Destination uSearch Tools
Navigation
Search Tools
H (Home) u Navigation uuSearch Tools
Find a location to set as the destination by searching for an address, intersection,
city, dealership, coordinates or phone number.
Select an option.
The following options are available:
• Address: Sets a destination by entering an address.
2 Finding an Address P. 61
• Intersections: Sets a destination by finding an intersection.
2 Finding a Location by Intersections P. 62
• Cities: Sets a nearby city as the destination.
2 Finding a City P. 63
• Dealerships: Sets a nearby Honda authorized dealer as the destination.
2 Finding a Dealership P. 64
• Coordinates: Sets a destination by entering coordinates.
2 Finding a Location Using Coordinates P. 65
• Phone Number: Sets a destination by entering a phone number.
2 Finding a Location by Phone Number P. 66
60
Navigation
Finding an Address
1 Finding an Address
Using Voice Command
You can say the entire address at once using voice
commands.
From the Voice Portal screen, say “Navigation.”
Say “Find Address” on the voice command
screen, then say the entire address. (e.g., “1-2-3-4
Main Street, Los Angeles, California”).
Say “Change Country” if you want to change the
country.
The system interprets the address.
Say “Yes” or a line number of a screen if the
destination list appears (e.g., “1”).
Say “Go” to set the route.
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
The order of the steps may change depending on the
map data loaded on your system.
■
H (Home) u Navigation uuSearch Tools u Address
Enter an address to use as the destination.
uuEntering a Destination u Search Tools
1. Enter the house number and street
name.
u Select Searching near if you
want to search different city.
2. Select Done or a suggestion.
3. Select your destination from the
list.
4. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
Continued
61
uuEntering a Destination uSearch Tools
Navigation
1 Finding a Location by Intersections
Using Voice Command
You can find intersections by the street name using
voice commands.
From the Voice Portal screen, say “Navigation.”
Say “Find Intersection” on the voice command
screen and then say a city name.
Say a street name 1, then say a line number of a
screen (e.g., “1”).
Say a street name 2, then say a line number of a
screen (e.g., “1”).
Say “Go” to set the route.
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
Finding a Location by Intersections
■
H (Home) u Navigation uuSearch Tools u Intersections
Select the intersection of two streets as the destination.
1. Enter two street names.
u A list of matching hits is
automatically displayed after
you enter several letters with
the closest match at the top of
the list.
2. Select Done or a suggestion.
3. Select the intersection from the
list.
4. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
62
Navigation
Finding a City
1 Finding a City
Using Voice Command
You can find a city by using voice commands.
From the Voice Portal screen, say “Navigation.”
Say “Find City” on the voice command screen,
then say a city name. (e.g., “Los Angeles”).
Say a line number of a screen (e.g., “1”).
Say “Go” to set the route.
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
■
H (Home) u Navigation uuSearch Tools u Cities
Selects your destination city.
uuEntering a Destination u Search Tools
1. Select a city.
u Cities near your current
position are listed.
Select Enter City and State
and enter city and state names
if you want to find different
city.
2. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
Continued
63
uuEntering a Destination uSearch Tools
Navigation
Finding a Dealership
■
H (Home) u Navigation uuSearch Tools u Dealerships
Find any Honda authorized dealers to set as a destination.
1. Select the desired name from the
list.
u Select the search bar and enter
a dealership name to narrow
down the number of matches.
2. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
64
Navigation
Finding a Location Using Coordinates
1 Finding a Location Using Coordinates
If you want to change the coordinate format, select
and then select Coordinate Format.
You can add the coordinates location to the saved
location list by selecting Save.
■
H (Home) u Navigation uuSearch Tools u Coordinates
You can find a location using latitude and longitude coordinates. This can be helpful
when geocaching.
uuEntering a Destination u Search Tools
1. Select Change.
2. Select the latitude coordinate and
enter the new coordinate.
u Select N/S if necessary.
3. Select the longitude coordinate
and enter the new coordinate.
u Select E/W if necessary.
4. Select Done.
5. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
Continued
65
uuEntering a Destination uSearch Tools
Navigation
Finding a Location by Phone Number
■
H (Home) u Navigation uuSearch Tools u Phone Number
Search for your destination by entering a phone number.
1. Enter the phone number.
u Select Searching in and select
another area if you want to
change the search area.
2. Select Done or a suggestion.
3. Select your destination from the
list.
4. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
66
Navigation
Categories
1 Categories
This option is convenient if you do not know the
exact name of a place or if you want to narrow down
the number of matches returned for places with a
common name.
Select the category of a place (e.g., Restaurants, Gas Stations, Shopping) stored in
the map database to search for the destination.
Finding a Location by Category
■
H (Home) u Navigation uuCategories
uuEntering a Destination u Categories
1. Select a category.
2. Select a subcategory.
u If the subcategory screen is not
displayed, proceed to step 3.
3. Select a place name from the list.
4. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
67
uuEntering a Destination uSaved
Navigation
1 Saved
You can add, edit, or delete the saved place.
2 Saved Locations P. 19
Using Voice Command
You can utilize a saved place by using voice
commands.
From the Voice Portal screen, say “Navigation.”
Say “Saved Places” on the voice command
screen, then say a saved place (e.g., “Honda”).
Say “Go” to set the route.
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
1 Recents
You can delete a recent destination. Select a destination
to delete, select , and then select
Delete
.
If you want to delete all recent destinations, select
without selecting any destination in the list, and
then select Clear All Recent Places.
Using Voice Command
You can utilize a recent destination by using voice
commands.
From the Voice Portal screen, say “Navigation.”
Say “Recent Places” on the voice command
screen, then say a line number of a screen (e.g.,
“1”).
Say “Go” to set the route.
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
Saved
H (Home) u Navigation uuSaved
Select a saved location to use as the destination.
Recents
H (Home) u Navigation uuRecents
1. Select your destination from the
list.
2. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
Select a location from a list of your 50 most recent destinations to use as the
destination. The list is displayed with the most recent destination at the top.
68
1. Select your destination from the
list.
2. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
Navigation
myTrips
1 myTrips
You can create, edit, or delete trips.
2 Saved Trips P. 26
H (Home) u Navigation uumyTrips
Set the route to your destination selecting a saved trip.
uuEntering a DestinationumyTrips
1. Select a trip.
2. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
u Select Turn List to display turn-
by-turn instructions and
information for each turn.
69
uuEntering a Destination umyTrends
Navigation
1 myTrends
Set Travel Data Recording to On to use myTrends
feature.
2 Location History P. 49
You can delete myTrends location. Select the location
to remove, select and then select Remove.
To delete all myTrends locations, select without
selecting any location and then select Remove All in
the myTrends list screen.
1 Predicted Destination
To use this feature, set Predicted Destination Alert
to On.
2 Location History P. 49
The notification will be queued in the queue indicator
after a certain period of time. Select the indicator to
display the predicted destination.
myTrends
H (Home) u Navigation uumyTrends
Select a frequently-visited place to use as the destination.
Predicted Destination
■
When you start the vehicle, the system predicts the most-likely destination based on
your travel data. It displays the notification window to offer the destination and
show related information.
1. Select your destination from the
list.
2. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
Select Go! to accept the predicted
destination.
70
Navigation
Map Input
1 Map Input
“Show Map”
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
You can customize the map as you like using ,
, , or .
2 Map Operation P. 82
H (Home) u Navigation
Scroll the map to manually select an icon or a location as the destination.
uuEntering a Destination uMap Input
1. Tap on the map screen and then
select any point on the map, a
street, intersection, or category
icon.
u Return to the current location
when you press the (Back)
icon.
2. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
71
Navigation
Calculating the Route
1 Calculating the Route
If the route is very long, the system will calculate the
route to the first guidance point and start the
guidance. The system will then continue calculation
to final destination as you proceed.
Select to view the map with the location
centered.
This section describes how to calculate your route.
The following options are available:
• Routes: Displays different routes.
2 Viewing and Selecting the Routes P. 73
• Info: Displays detailed location information.
2 Viewing the Location Information P. 74
Select Go!.
u The system calculates and displays
the route line on the map screen.
72
uuCalculating the RouteuViewing and Selecting the Routes
Navigation
Viewing and Selecting the Routes
View and select different routes to your destination.
1. Select your desired route.
u The estimated arrival time and
travel distance are displayed for
each route.
2. Select Go!.
u The system calculates and
displays the route line on the
map screen.
73
uuCalculating the Route uViewing the Location Information
Navigation
Viewing the Location Information
1. Select an option.
2. Select Go!.
u The system calculates and
displays the route line on the
map screen.
The following options are available:
• Save: Adds the destination to the saved location list.
2 Saved Locations P. 19
• Set Location: Sets the vehicle position when you are indoors or not receiving
satellite signals.
You can use this feature when GPS Simulator is set to on.
2 Navigation P. 40
• Routes: Displays different routes to the destination.
2 Viewing and Selecting the Routes P. 73
• Routes Settings: Changes the route preferences.
2 Navigation P. 40
74
Navigation
Driving to Your Destination
1 Viewing the Route
When your phone is connected to Bluetooth®
HandsFreeLink®, the navigation screen will switch to
the incoming call screen when receiving a call.
Speed limit icon
The speed limit shown on the map may be different
from the actual speed limit.
The speed limit icon is not displayed on all roads.
Select the vehicle icon to view the Where Am I?
screen.
2 Viewing the Current Location Information
P. 87
You can stop your vehicle en route (e.g., to rest, stop
for gas, etc.), and then continue on your route.
If you did not complete your route, the navigation
restarts when you restart your vehicle.
When LaneWatch
*
is activated, the navigation screen
will switch to the LaneWatch screen.
The next guidance indicator does not appear in the
following cases.
•
The vehicle speed is 3 mph (4.8 km/h) or less
•
The GPS signal is weak
•
The vehicle position on the map and current vehicle
position do not match
Next guidance indicator
Speed limit icon
Dashboards
Queue indicator
* Not available on all models
Viewing the Route
This section describes how to follow the route guidance to your destination.
Map Screen
■
The following options are available:
• Select the next guidance indicator to replay the voice guidance for the next
maneuver.
• Select the text bar on the top of the map to display the turn list screen.
2 Turn List Screen P. 77
• Select the queue indicator to display queued notifications.
2 Alert and Notification Banners P. 78
• Select to display the map tools window.
2 Map Tools P. 83
After calculating the route to your
destination, the route is displayed on
the map screen.
2 During Route Guidance P. 7
As you drive, the system tracks your
position on the map in real time and
provides guidance as you approach
each guidance point on the route.
Continued
75
uuDriving to Your Destination u Viewing the Route
Navigation
1 Viewing the Route
Turn-by-Turn Directions
The next guidance point appears on the Driver
Information Interface.
The Turn-by-Turn directions may not be displayed if
the information cannot be received correctly.
• Select the map dashboards when you want to change the information that is
displayed. Select the following options:
Elevation, Direction, Location, Arrival, Distance, Arrive In, Via Arrival, Via
Distance, Via In.
Intersection View Screen
■
The intersection view screen displays a view of the upcoming intersection and which
lane you should be driving.
76
uuDriving to Your Destinationu Viewing the Route
Navigation
1 Turn List Screen
When you are on the multi-destination route, the list
is separated for each route leg. You can skip from the
current route leg to another route leg by selecting
Go! displayed on the top of each route leg.
Turn List Screen
■
The turn list screen displays turn-by-turn instructions and the distance between
turns.
1. Select the text bar on the top of
the map.
2. Select a turn to display on the
map.
Full Route Screen
■
The full route screen displays the entire route and current vehicle position.
1. Select the text bar on the top of
the map.
2. Select .
3. Select View Full Route.
Continued
77
uuDriving to Your Destination u Viewing the Route
Navigation
1 Alert and Notification Banners
After a certain time of period, the alert or notification
is queued in the queue indicator.
You can view the alert or notification again by
selecting the queue indicator.
If the notifications center window is displayed, select
the notification from the list.
Alert and Notification Banners
■
The slide-in banner appears on the top of the map screen when the system provides
an alert or notification.
■ School Zone Proximity Alert
A proximity alert for school zone is displayed when the system receives the
information.
■ Parking Reminder Notification
A parking reminder notification is displayed when you approach your destination.
Select the banner to display the
distance to the alert point, speed
limit, and map preview with the alert
point centered.
Select the banner to display the list of
parking near the destination.
78
uuDriving to Your Destinationu Viewing the Route
Navigation
1 Off-Road Breadcrumbs Display
You can delete the off-road breadcrumbs.
2 Location History P. 49
2 Reset Factory Default Settings P. 51
Off-Road Breadcrumbs Display
■
If you set the off-road breadcrumbs to show, a series of lines (breadcrumbs) are
displayed to track your movement on a off-road.
2 Map Layer P. 37
Deviating From the Planned Route
■
If you leave the calculated route, the system automatically recalculates a route to the
set destination based on your current location and direction.
If your vehicle is off a road segment, the system shows a dotted line indicating the
direction back to the calculated route.
79
uuDriving to Your Destination u Traffic Information
Navigation
1 Traffic Information
Continuously updated traffic information is available
in major metropolitan areas across contiguous United
States and some cities in Canada.
You can change the traffic information settings.
2 Traffic P. 48
1 Viewing Traffic Alert
The notification will be queued in the queue indicator
after a certain period of time. Select the indicator to
display the notification again.
Traffic Information
When you set the traffic feature, the system examines traffic conditions and
optimizes the route for the shortest time. If a severe traffic delay occurs while you
are navigating, the system searches for a faster route. If it finds one, the system will
automatically alter the route and display the reroute notification banner on the map
screen.
The system may route you through a traffic delay if a better alternative route does
not exist. The delay time is added into your estimated time of arrival automatically.
Viewing Traffic Alert
■
The traffic alert window is displayed on the map screen when traffic may cause a
delay.
Select the reroute notification banner
to view the saved time and avoided
traffic events.
u Select Use Original Route to use
the original route.
Select the window to view detailed
information and the map.
80
uuDriving to Your Destinationu Traffic Information
Navigation
Viewing Traffic Delays Manually
■
H (Home) u Navigation uuTraffic
View the traffic flow and delays on nearby roads.
Viewing Traffic Legends
■
H (Home) u Navigation uuTraffic uuTraffic Legend
See an overview of the icons and colors used on the traffic map.
Select the traffic information window
to view detailed information and
map.
The system displays the traffic
legend.
81
Navigation
Map Operation
Customize the map, set a destination, and save a place from the map.
1. Select any point on the map.
2. Select an option.
u If you want to set a destination
or save a location in the map,
The following options are available:
• : Zooms in to the map.
• : Zooms out of the map.
• : Switches the map to 2D or 3D.
• : Rotates the 3D map.
• : Sets the data that appears on the map.
2 Map Layer P. 37
scroll the map and select the
desired location.
2 Saved Locations P. 19
2 Map Input P. 71
82
Navigation
Map Tools
1 Map Tools
You can rearrange the order of menu icons.
Select and hold the icon and move it to the desired
position.
H (Home) u Navigation u
The following options are available:
• Stop: Cancels the route guidance and removes your current route.
• Detour: Calculates a detour route.
2 Taking a Detour P. 89
• Exit Services: Displays a list of the exit services for the route.
2 Viewing Exit Services P. 84
• Guidance Volume: Adjusts the guidance volume.
2 Guidance Volume Settings P. 32
• Up Ahead: Displays the list of upcoming services along the road where you are
travelling.
2 Viewing Services Up Ahead P. 85
• Traffic: Displays traffic information.
2 Traffic Information P. 80
• Where Am I?: Displays the information about your current location.
2 Viewing the Current Location Information P. 87
• Settings: Changes settings for navigation functions.
2 System Setup P. 15
uuMap OperationuMap Tools
Select an option.
Continued
83
uuMap OperationuMap Tools
Navigation
Viewing Exit Services
■
H (Home) u Navigation uuExit Services
You can view exit services (e.g., whether the exit is near gas stations, restaurants,
etc.) and add new destinations or waypoints to the calculated route.
1. Select an exit.
2. Select a category.
3. Select a service.
4. Select an option.
2 Calculating the Route P. 72
2 Adding Waypoints P. 90
84
uuMap OperationuMap Tools
Navigation
1 Viewing Services Up Ahead
You can change the order of search results.
Select in the service list screen, select Sort POI
Results and then select an option.
Viewing Services Up Ahead
■
H (Home) u Navigation uuUp Ahead
You can view the list of upcoming services along the road where you are travelling.
1. Select a category.
2. Select a service from the list.
3. Select an option.
2 Calculating the Route P. 72
2 Adding Waypoints P. 90
Continued
85
uuMap OperationuMap Tools
Navigation
1 Customizing the Up Ahead Categories
You can change the order of categories.
Select and hold , or and then move the
category to the desired position.
■ Customizing the Up Ahead Categories
You can change the category to display.
1. Select in the service list screen.
2. Select Up Ahead Options.
3. Select the category to change.
4. Select a category to display.
u Select a subcategory if
necessary.
u Select Custom Search, and
enter the name of category to
create a custom category.
86
uuMap OperationuMap Tools
Navigation
1 Viewing the Current Location Information
Vehicle position may not be displayed when:
•
The vehicle is traveling off-road.
•
The vehicle position data cannot be updated.
When you deviated from the planned route, the
closest route-able road is also displayed.
Viewing the Current Location Information
■
H (Home) u Navigation uuWhere Am I?
You can confirm your current location, address, and nearest intersection.
Select an option.
The following options are available:
• Save: Saves your current location.
2 Saving Your Current Location P. 21
• Hospitals/Police Stations/Gas Stations/Tow Services: Searches for a hospital,
police station, gas station or tow service around your current location.
2 Searching Near Establishment P. 95
87
Navigation
Changing Your Route
1 Stopping the Route
“Stop route”
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
Stopping the Route
Stop the route guidance and remove the destination and all waypoints.
1. Select on the map screen.
2. Select Stop.
88
Navigation
Taking a Detour
1 Taking a Detour
“Detour”
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
If your current route is the only reasonable option,
the system might not calculate a detour.
H (Home) u Navigation uuDetour (when en route)
Calculates a new route to avoid something ahead of you. The system creates a new
route if possible. The system attempts to get you back on your original route as
quickly as possible.
Taking a Detour Around Specified Areas
■
You can take a detour for a specified distance along your route or detour around
specific roads. This is useful if you encounter construction zones, closed roads, or
poor road conditions.
The following options are available:
• Skip Next Turn: Calculates a new route by avoiding the next turn on your route.
• 0.5 mi.: Calculates a new route by avoiding the next 0.5 mile on your route.
• 2 mi.: Calculates a new route by avoiding the next 2 miles on your route.
• 5 mi.: Calculates a new route by avoiding the next 5 miles on your route.
uuChanging Your RouteuTaking a Detour
Select an option.
89
uuChanging Your RouteuAdding Waypoints
Navigation
1 Adding Waypoints
When you add a waypoint, the system may take
some time to update the arrival time.
Select Start New Route to set the location as your
new destination.
Select Add as Last Stop to add the location to the
end of your route.
2 Entering a New Destination P. 97
Adding Waypoints
Add waypoints (pit stops) along the route to your destination.
1. While en route, select a search
method to add a new destination
or waypoint.
2 Entering a Destination P. 54
2. Select a place. Select Go!.
3. Select Add as Next Stop or Add
to Active Route.
u Select Add as Next Stop to set
the location as your next
waypoint. The route is
automatically recalculated and
displayed on the map screen.
u If selecting Add to Active
Route, proceed to steps 4 and 5.
4. Select and hold , or and
then move the destination to the
desired position.
5. Select Go!.
u The route is automatically
recalculated and displayed on
the map screen.
90
uuChanging Your RouteuEditing the Route
Navigation
Editing the Route
You can edit destinations on your route and save the route as your favorite trip.
Reordering Destinations
■
H (Home) u Navigation
1. Select the text bar on the top of
the map.
2. Select .
3. Select Edit Destinations.
4. Select and hold , or and
then move the destination to the
desired position.
u Select Add Destinations to
add a new location.
5. Select .
u The route is automatically
recalculated.
Continued
91
uuChanging Your RouteuEditing the Route
Navigation
Deleting a Destination
■
H (Home) u Navigation
1. Select the text bar on the top of
the map.
2. Select .
3. Select Edit Destinations.
4. Select .
5. Select Remove Destinations.
6. Select the location to delete.
u Select Select All to delete all
destinations.
7. Select Remove.
8. Select .
u The route is automatically
recalculated.
92
Navigation
Saving Your Current Route
1 Saving Your Current Route
You can use the saved trip from myTrips screen.
2 myTrips P. 69
You can also save your current route from myTrips
screen. Select on the routing map, and then
select myTrips. Select Save.
■
H (Home) u Navigation
You can add the current route to myTrips list.
uuChanging Your RouteuEditing the Route
1. Select the text bar on the top of
the map.
2. Select .
3. Select Save Route.
4. Enter a name.
5. Select Done.
93
Navigation
Changing Your Destination
Selecting a Destination on the Map
Select a new destination when en route by selecting a location on the map.
1. Select any point on the map, or a
street, intersection, or category
icon.
2. Select Go!.
3. Select an option.
The following options are available:
• Start New Route: Sets the location as your new destination.
• Add as Next Stop: Sets the location as the next waypoint.
• Add as Last Stop: Adds the location as your last destination.
• Add to Active Route: Sets the location as the waypoint and edits the order of
destinations in your route.
2 Adding Waypoints P. 90
94
Navigation
Searching Near Establishment
1 Searching Near Establishment
You can also search for nearby establishment by
selecting on the map screen and select Where
Am I?.
H (Home) u Navigation
Search for a hospital, police station, gas station or tow service around your current
location.
uuChanging Your DestinationuSearching Near Establishment
1. Select your vehicle icon.
u You can also confirm your
current location, address, and
nearest intersection.
2. Scroll down to the bottom, and
then select a category type.
3. Select a place.
4. Select Go!.
Continued
95
uuChanging Your DestinationuSearching Near Establishment
Navigation
5. Select an option.
The following options are available:
• Start New Route: Sets the location as your new destination.
• Add as Next Stop: Sets the location as the next waypoint.
• Add as Last Stop: Adds the location as your last destination.
• Add to Active Route: Sets the location as the waypoint and edits the order of
destinations in your route.
2 Adding Waypoints P. 90
96
uuChanging Your DestinationuEntering a New Destination
Navigation
Entering a New Destination
H (Home) u Navigation u
Enter a new destination using the destination menu screen even when you are en
route.
1. Select a search method to enter a
The following options are available:
• Start New Route: Sets the location as your new destination.
• Add as Next Stop: Sets the location as the next waypoint.
• Add as Last Stop: Adds the location as your last destination.
• Add to Active Route: Sets the location as the waypoint and edits the order of
destinations in your route.
2 Adding Waypoints P. 90
new destination.
2 Entering a Destination P. 54
2. Select a place and then select Go!.
3. Select an option.
97
98
Loading...