The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd., reserves the right,
NOTICE
3
WARNING
however, to discontinue or change specifications or design at any time without notice and without incurring any obligation.
Accessories Precautions
The GPS antenna is located in the dashboard. Metallic front or side window tinting can seriously degrade or obstruct GPS reception.
Signal noise from devices such as radar detectors, vehicle tracking devices, remote starters, and additional amplifiers can disrupt the navigation system. If you
install any such item, install it away from the navigation display and antenna.
Important Safety Information
Using the navigation system while driving can take your
attention away from the road, causing a crash in which you
could be seriously injured or killed.
Only operate system controls when the conditions permit you
to safely do so.
Avoid focusing on the screen or manually operating the system controls while driving.
Certain on-screen controls are disabled when driving, however most of t
more attention and time to look at the screen or access additional menus.
Route guidance may conflict with street closures, road construction,
The system itself may also have limitations. Verify route information by carefully observing roads, signs, and signals. Always use your own judgment an
traffic laws.
System Limitations
2
This vehicle’s navigation display, if so equipped, includes mercury-containing components. Upon removal, please reuse, recycle, or dispose of as hazardous waste.
Clean the screen with a soft, damp cloth. You may use a mild cleaner intended for use on navigation screens.
P. 106
he voice co
detours, and out-of-date map data.
mmands continue to function. Pull to the side of the road if you need to devote
Start-up 16Voice Control System 17Personal Information 18Display Mode Settings 30
Guidance Volume Settings 32Map and Vehicle 33Navigation 40Traffic 48
Location History 49About 50Data Reset 51
2 Navigation P. 53
Entering a Destination 54Calculating the Route 72Driving to Your Destination 75Map Operation 82
Changing Your Route 88Changing Your Destination 94
Contents
Quick Reference Guide
System Setup
Navigation
P. 2
P. 15
P. 53
2 Troubleshooting P. 99
Troubleshooting 100
2 Reference Information P. 105
System Limitations 106Customer Assistance 108Legal Information 110
2 Voice Commands P. 117
Voice Commands 118List of Categories 121
Troubleshooting
Reference Information
Voice Commands
Index
P. 99
P. 105
P. 117
P. 122
Quick Reference Guide
Quick Reference Guide
Store home address
(P18)
Register
1
home address.
Track route
(P75)
Follow your route in real-time with voice guidance.
Store contacts
(P19)
Store locations to use as the destination.
Enter destination
(P54)
Select your destination using several methods.
Select route
(P73)
Set route preferences and select one of the available routes.
Avoid certain areas
(P43)
Set streets and areas to detour around.
Add waypoints
(P90)
Add “pit stops” along your route.
Traffic Information* (P80)
View and avoid congestion and traffic incidents.
*: Available only in certain areas.
Overview—Functions at a Glance
Navigation
You can select any place/landmark as a destination by using the touchscreen. The navigation system gives you
turn-by-turn driving directions to your destination.
2
Quick Reference Guide
HOME Screen
(Home)
Display the HOME screen.
(Back)
Go back to the previous screen.
(Display Mode)
Switch between Day and Night modes manually.
VOL (Volume)
Increase or decrease the audio/
guidance volume.
Navigation
Display the navigation feature that was
used the last time.
At start-up, the map screen is displayed.
(Map)
Display the map screen.
The system displays various functions from the HOME screen. Press the (Home) button at any time to return to the main HOME screen.
3
Quick Reference Guide
Touchscreen Operation
You can operate the system using your finger on the touchscreen.
The touchscreen can be operated if you are wearing thin gloves, but it may be more diff
icult for the system to respond.
Tap
Touch the screen lightly with your finger to select an option on the
screen.
Swipe
Lightly sweep your finger side to side or up and down to scroll a list
or map.
You can change the touchscreen sensitivity setting.
2 Refer to the O
wners Manual.
Slide
Move your finger slowly across the screen to scroll the map.
Pinch In/Out
Open or close your fingers on the screen in a pinching motion to
zoom in or out of the map.
4
Quick Reference Guide
On input search screens, the suggested search terms are
displayed. Select Done to display a list of possible entries.
How to Enter Information
You can enter information (e.g., city names, street names, numbers, and symbols) when prompted on the input screen.
Using Voice Commands
When you see in this manual, voice commands are available for
that feature.
The system recognizes only certain co
Available navigation commands (P118)
Press the button, and say the command, phrase, letter,
number, or symbol (e.g., say “1”).
If a voice command is not recognized, a list is displayed with
possible options.
mmands.
On list screens:
Say the number of the list item (e.g., say “Three” to select
item 3).
Say “Back”
Say “Next”
Say “Previo
Say “Can
to return to the previous screen.
for next page.
us” for previous page.
cel” to end the voice command function.
Using the Touchscreen
Select a character or icon on the screen to select it.
Select to remove the last entered character.
Select to remove all entered characters.
Select to display upper/lower case characters.
Select Spa
Select to display other types of characters.
Select to change the keypad language.
ce to enter a space character.
5
Quick Reference Guide
Map Screen Legend
Map operation icons
(P82)
Current vehicle position
Streets
Landmark icons
Map scale (P82)
Map tools (P83)
Feature areas
Where To?
(P54)
The color of the map is different depending on the selected Map Theme.
6
Quick Reference Guide
Dashboards (P75)
Next guidance indicator (P75)
Distance to the next guidance point and street name of
next guidance point.
Select to get next voice guidance.
Queue indicator
Where To? (P54)
Calculated route
Current street name
Waypoint
Street name of next
guidance point
Distance to next
guidance point
Estimated time to
next guidance point
Day ModeNight Mode
Remaining
distance
Street name of next
guidance point
Next driving maneuver is
approaching.
During Route Guidance
During route guidance, route information is displayed on the map screen.
You can see the detailed information on the turn list
screen.
Map Screen
Guidance Screen
Day or Night Mode
Press the button to manually
switch between Day and Night modes.
Turn-by-Turn Directions
The next guidance point appears on
the Driver Information Interface.
7
Quick Reference Guide
Navigation—Home Addresses and Going Home
The “Home” feature automatically routes you to your home address from any location simply by selecting Go Home.
You can store one home address. (P18)
The order of the steps may change depending on the map data loaded on your system.
Storing Your Home Address
a Press the button.
b Select .
c Select and then select Set Home
Location.
d Select Enter My Address.
e Enter a house number and street
name.
f Select Done or a suggestion.
g Select an address from the list.
h Select Select.
Going Home
a Press the button.
b Select .
c Select Go Home.
Alternatively, you can say
vigation” and then “Go
“NaHome”
from any screen.
8
Quick Reference Guide
Navigation—Entering a Destination
Enter your destination using one of several methods, then follow route guidance on the map to your destination.
The order of the steps may change depending on the map data loaded on your system.
a Press the button.
b Select .
c Select the search bar.
d Enter the house number and street
name.
e Select Done or a suggestion.
f Select an address from the list.
g Select Go!.
Route guidance to the destination
ins.
beg
Routes: Choose one of multiple routes.
Info: Display the location information
save a place.
and
9
Quick Reference Guide
Navigation—Changing Route or Destination
You can alter your route by adding waypoints to visit, or changing your destination during route guidance.
Adding a Waypoint (“Pit Stop”)
You can add waypoints along your route.
(P90)
a Press the button.
b Select .
c Select a search method.
d Select the location to add to the
destination list and select Go!.
e Select Add as Next Stop or Add to
Active Route.
f If necessary, edit the order of the
destinations.
Changing Your Destination
There are several methods you can use to
specify a new destination during route
guidance.
Searching nearby hospitals, police
stations, gas stations
(P95)
Select the vehicle icon and select an
tion.
op
Selecting an icon on the map (P94)
Select a place/landmark icon or a new
n the map twice.
area o
Entering a new destination (P97)
Select Wh
destination.
ere To? and then enter a new
, or tow services
Canceling Your Route
a Select .
Alternatively, you can say
vigation” and then “Stop
“Naroute” from
any screen.
10
Quick Reference Guide
Voice Control Operation
Voice Portal Screen
a Press and release the button.
The system beeps when ready for a
mmand. Press the button to
co
cancel.
b Say “Navigation.”
The Voice Command screen is
disp
layed.
After that follow the voice prompt
an
d say a voice command.
The audio system is muted during voice
control mode.
You can use other voice commands on
ice Portal screen.
the Vo
Carefully read the usage note for the
The system recognizes only certain
ontrol.
voice c
Voice Control System(P17)
co
mmands.
Available navigation commands
)
(P118
Voice Command Screen
a After saying “Navigation” from
the Voice Portal screen, the below
screen ap
b Listen for the voice prompt, then say a
voice command.
You do not need to press the
button again in the Voice Command
screen.
Available voice commands are
hig
pears.
hlighted on the screen.
11
Quick Reference Guide
Troubleshooting
For more Information
(P99)
Why does the vehicle position icon on the map appear
slightly off my actual position, especially at intersections?
This is normal. The navigation system is unaware of the
width of intersections. Large differences in vehicle position
can indicate a temporary loss of the GPS signal.
Why does the “Arrival time” display sometimes increase
even though I am getting closer to my destination?
The “Arrival time” is based on the speed limit on each
road. Depending on the traffic conditions, the “Arrival
time” may be calculated to be earlier or later.
Why does my clock frequently change the time forward
and backward by one hour?
The clock setting is automatically updated based on your
GPS location. If you are driving near a time zone border,
the automatic update likely is the reason.
How do I turn on the navigation system voice guidance?
●
Adjust the volume using the volume knob during the
voice guidance.
●
Press the button.
Select Settings > System > System Vol
umes >
System Volumes.
Turn up volume level of Navi
gation On Guidance if it
is low.
How do I specify a destination when an entered city or
street could not be found?
Try selecting the destination directly from the map.
12
How to Use This Manual
Searching the Table of Contents
(P1)
First, find the general chapter related to
what you are looking for (e.g., entering
a destination from the Saved Places).
Then, go to that chapter to view a more
specific table of contents.
Searching the Index
(P122 )
This more detailed table of contents
shows you exactly what information is
listed by section and title.
The Index consists of
main terms and subentries. The sub-entries
help you get to the
desired page depending
on what you are looking
for.
Table of Contents
Chapter Contents
Navigation Screen
Index
Two types of Tables of Contents help
you find your desired information.
Menu items displayed on the
navigation screen (e.g., Saved) can be
found individually in the Index.
More Detailed
Contents
Go to the
Next Page
This section explains different methods on how you can easily find information in this manual.
13
uuEntering a Destination uSaved
Navigation
Saved
HuuSaved
Select a saved location to use as the destination.
1. Select your destination from the
list.
2. Select Go! to set the route to your
destination.
2 Calculating the Route P. 72
Recents
HuuRecents
Select a location from a list of your 50 most recent destinations to use as the
1 Saved
You can add, edit, or delete the saved place.
2 Saved Locations P. 19
Using Voice Command
You can utilize a saved place by using voice
commands.
From the Voice Portal screen, say “Navigation.”
Say “Saved Places” on the voice command
screen, then say a saved place (e.g., “Honda”).
Say “Go” to set the route.
2 Using Voice Commands P. 5
2 Voice Control Operation P. 11
Select the item on the system
control panel.
Menu Tree
The menu tree helps guide you
through the system’s menu options.
To get to your desired function, follow
the menu tree in order of the steps
shown.
Select the menu option.
After following the menu
tree, step-by-step
instructions explain how to
achieve the desired result.
* Sample pages and images in this section may differ from the actual ones.
Select Saved.
Saved
14
System Setup
This section describes the start-up procedure and the navigation and setup functions.
When you use the navigation system, the system may
close other apps.
When you select Navigation, the system displays the
navigation feature that was used the last time. At
start-up, the map screen is displayed.
The navigation system starts automatically when you set the power mode to
ACCESSORY or ON. At start-up, the following confirmation screen is displayed.
Limitations for Manual Operation
■
Certain manual functions are disabled or inope
You cannot select a grayed-out option until the vehicle is stopped.
Voice commands are still operable while the vehicle is in motion.
1. Select OK.
u The HOME screen is displayed.
u If you do not select OK, the
system will automatically select
OK after a certain period of
time.
u The system
start up the feature that was
last in use.
2. Press the button.
u The map screen is displayed.
rable while the vehicle is in motion.
will automatically
16
System Setup
Voice Control System
1 Voice Control System
When you press the button, the system prompts
you to say a voice command. Press and release the
button again to bypass this prompt and give a
command.
1 Voice Recognition
The voice control system can only be used from the
driver’s seat because the microphone unit removes
noises from the front passenger’s side.
Your vehicle has a voice control system that allows hands-free operation of the
navigation system functions.
The voice control system uses the and buttons on the steering wheel and a
microphone near the map lights on the ceiling.
For details of the button, button and microphone position, see the Owner's
Manual.
Voice Recognition
To achieve optimum voice recognition when using the navigation voice control
system:
• Make sure the correct screen is displayed for the voice command that you are
using. The system recognizes only certain commands.
Available navigation commands:
2 Voice Commands P. 118
• Close the windows and moonroof.
• Adjust the dashboard and side vents so air does not blow onto the microphone
on the ceiling.
• Speak in a clear, natural speaking voice without pausing between words.
• Reduce any background noise if possible. The
command if more than one person is speaking at the same time.
system may misinterpret your
17
System Setup
Personal Information
1 Personal Information
The home location can be overwritten. Select
Change Home Location in step 1.
Setting Home Location
H u u
From any location, select Go Home and the system will provide you with one or
more return routes to your home.
Before you can use this feature, you need to re
system.
gister your home address with the
1. Select Set Home Location.
The following options are available:
nter My Address: Sets the home location by entering the address.
• E
2 Storing Your Home Address P. 8
• Use Current Location: Sets your current location as your home location.
• Recently Found: Sets the home location from a recently found location.
• Saved Place: Sets the home location from a saved place.
18
2. Select an
u Select Use Current Location
u If sel
3. Select
4. Select Select.
option.
to set home location.
ecting Enter My Address,
Recently Found or Saved
Place, proceed to steps 3 and 4.
the home location.
System Setup
Saved Locations
You can save locations so you can quickly find them and create routes to them.
■
H u
uu Personal Information u Saved Locations
Saving a Location
1. Select a search method.
u Find a location that you want to
save.
2 Entering a Destination P. 54
2. Select Info.
3. Select Save.
4. Enter a name and select Done.
Continued
19
uu Personal Information u Saved Locations
System Setup
Saving a Location Manually
■
H
1. Select
2. Select the destination name at the
3. Select Save.
a destination from the map.
2 Map Input P. 71
bottom of the map.
20
4. Enter
Done.
the place name and select
System Setup
Saving Your Current Location
1 Saving Your Current Location
Vehicle position may not be displayed when:
•
The vehicle is traveling off-road.
•
The vehicle position data cannot be updated.
■
H
uu Personal Information u Saved Locations
1. Select the vehicle icon.
2. Select Save.
3. Enter a name of the location.
4. Select Done.
Continued
21
uu Personal Information u Saved Locations
System Setup
Editing a Saved Location
■
H u u Saved
1. Select a
to edit.
2. Select Info.
3. Select .
4. Select Edit.
saved location you want
22
System Setup
The following options are available:
• Na
• Phone Number: Enters a phone number.
• Map Symbol: Select a symbol.
uu Personal Information u Saved Locations
5. Select an option.
me: Enters a new name for the location.
Continued
23
uu Personal Information u Saved Locations
System Setup
Deleting a Saved Location
■
H u u Saved
1. Select a
to delete.
2. Select Info.
3. Select .
4. Select De
5. Select Delete.
saved location you want
lete.
24
System Setup
■
H u u Saved
Deleting Saved Locations
1. Select .
2. Select Delet
uu Personal Information u Saved Locations
e Saved Places.
3. Select a
to delete.
u Select Select All to delete all
4. Select Delet
5. Select Delete.
saved location you want
saved locations.
e.
25
uu Personal Information u Saved Trips
System Setup
Saved Trips
You can use myTrips feature to create and save a route with multiple destinations.
Creating Your Trip
■
H u u myTrips u Create Trip u Add Starting Point
1. Select a method to enter a new
destination.
2 Entering a Destination P. 54
2. Select Select if necessary.
3. Select Add Destinations to add
additional locations.
u Repeat steps 1 and 2 to enter
the destination.
u Select and
then move the destination to
the desired position.
hold , or and
26
System Setup
Editing a Saved Trip
1 Editing a Saved Trip
The route preference is just for the trip. If you want to
change the route preference for routing, change the
navigation settings.
2 Calculation Mode P. 41
2 Avoidances P. 42
■
H u u myTrips
The following options are available:
• Trip Name: Enters a new name for the saved trip.
• Optimize Order: Automatically orders the waypo
• Calculation Mode: Changes the route preferences (calculating method).
• Avoidances: Changes preferences for route options to avoid.
1. Select a
saved trip you want to
edit.
2. Select Trip Settings.
3. Select an option.
ints in the destination list.
uu Personal Information u Saved Trips
Continued
27
uu Personal Information u Saved Trips
System Setup
■ Reordering Destinations
■ Deleting a Destination
1. Select a trip from myTrips list.
2. Select Edit Desti
nations.
3. Select and hold , or and
then move the destination to the
desired position.
u Select Add Des
tinations to
add a new location.
u The route is automatically
recalculat
ed.
1. Select a trip from myTrips list.
2. Select Edit Destinations.
3. Select .
4. Select Remove D
estinations.
5. Select the location to delete.
u Select Select All to delete all
destinations.
6. Select Re
move.
28
Loading...
+ 97 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.