T-IO
■
à Pàrh Liât
<S>/
Ht
Ж
mm
m
Ж
PART NO. 24739
mnEKs
Safety
□ □ □
□ Know the controls and how to stop quickly-READ THE
OWNER'S MANUAL.
□ Do not allow children to operate vehicle. Do not allow
adults to operate it without proper instruction.
D Do not carry passengers. Keep children and pets a safe
distance away.
□ Clear work area of objects which might be picked up and
thrown.
□ Disengage all attachment clutches and shift into neutral
before attempting to start engine (motor).
D Disengage power to attachments and stop engine (motor)
before leaving operator position.
□ Disengage power to attachment(s) and stop engine
(motor) before making any repairs or adjustments.
□ Disengage power to attachments when transporting or
not in usa
□ Take all possible precautions when leaving vehicle un
attended; such as disengaging power-take-off, lowering
attachments, shifting into neutral, setting parking brake,
stopping engine and removing key.
□ Do not stop or start suddenly when going uphill or down
hill. Mow up and down the face of steep slopes; never
across the face.
□ Reduce speed on slopes and in sharp turns to prevent
tipping or loss of control. Exercise extreme caution when
changing direction on slopes.
□ Stay alert for holes in terrain and other hidden hazards.
□ Use care when pulling loads or using heavy equipment.
A. Use only approved drawbar hitch points.
B. Limit loads to those you can safely control.
C. Do not turn sharply. Use care when backing.
D. Use counterweight(s) or wheel weights when
suggested in owner's manual.
□ Watch out for traffic when crossing or near roadways.
□ When using any attachments never direct discharge of
material toward bystanders nor allow anyone near vehicle
while in operation.
□ Handle gasoline with care — it is highly flammable.
A. Use approved gasoline container.
B. Never remove cap or add gasoline to a run
ning or hot engine or fill fuel-tank indoors.
Wipe up spilled gasoline.
C. Open doors if engine is run in garage — ex
haust fumes are dangereous. Do not run
engine (motor) indoors.
D Keep vehicle and attachments in good operating condi
tion and keep safety devices in place.
□ Keep all nuts, bolts, and screws tight to be sure equip
ment is in safe working condition.
□ Never store equipment with gasoline in the tank inside a
building where fumes may reach an open flame or spark.
□ Allow engine to cool before storing in any enclosure.
□ To reduce fire hazard keep engine free of grass, leaves or
excessive grease.
D Vehicle and attachment should be stopped and inspected
for damage after striking a foreign object and the damage
should be repaired before restarting and operating the
equipment.
□ Do not change engine governor settings or overspeed
engine.
□ When using vehicle with mower:
(1) Mow only in daylight or in good artificial
light.
(2) Never make a cutting height adjustment
while engine (motor) is running if operator
must dismount to do so.
(3) Shut engine (motor) off when removing grass
catcher and/or unclogging chute.
(4) Check blade mounting bolts for proper tight
ness at frequent intervals.
□ Check grass catcher bags frequently for wear or deteri
oration, Replace with new bags for safety protection.
PTO Idler Assembly
1- SUPPORT ASSEMBLY LM-16070-64 1
2 SCREW-hex hd.-cap, 3/8-16 x 1-1/4 LM-09174-00 1
3 WASHER-lock, 3/8 LM-09169-65 4
4 NUT-hex, 3/8-16 LM-09169-50 3
5 BRACKET ASSEMBLY-idier LM-16070-73 2
6 PULLEY-idler LM-01010-96 2
7 WASHER-Uat LM-09249-40 6
8 SCREW-hex hd. cap, 3/8-16 x 1-1/2 LM-09193-60 2
9 CLEVIS ASSEMBLY LM-16070-56 1
10 PlN-spring LM-09160-01 2
11 WASHER-flat LM-09169-60 2
12 COTTER PIN LM-09184-52 3
13 ARM ASSEMBLY-pivot LM-16070-66 1
14 BEARlNG-nylon LM-16104-56 2
15 WASHER-nyton LM-01591-34 2
16 SCREW-speciai, cap LM-16071-24 1
17 NUT-hex lock, 3/8-16 LM-09234-28 1
18 KNOE-ball LM-16010-42 1
19 SCREW-hex hd. cap, 3/8-16 X 7/8 LM-09193-57 1
20 SPRING-extension LM-01737-47 1
21 WASHER-flat LM-09193-87 ' 2
22 BRACKET ASSEMBLY LM-16070-60 1
23 PLATE-reinfoi-cement LM-16070-61 1
24 BOLT-carriage, 5/16-18 x 1 LM-09211-58 2
25 WASHER-lock, 5/16 LM-09173-56 3
26 NUT-hex, 5/16-18 LM-09173-72 2
27 WASHER-flat LM-09176-42 1
28 SCREW-hex hd. cap, 5/16-18 X 2-1/2 LM-09234-23 1
29 PIN-rd.hd. LM-01563-06 2
30 PIN-quick LM-09181-96 2
ALWAYS FURNISH MODEL AND SERIAL NUMBER WHEN ORDERING PARTS.
Arbor Assembly
34
39 27
yin
30
ALWAYS FURNISH MODEL AND SERIAL NUMBER WHEN ORDERING PARTS.
f"—
©<—-—
—-31
f 1-
28
r
No. Description Part No.
CENTER ARBOR & HOUSING (notshown) LM-16075-82
CENTER ARBOR & HOUSING (notshown) LM-16075-83
Includes: (each)
1
2
3
4
5 WASHER-special
6 SHEAVE-mower spindle
7 WASHER-flat
8 SHEAVE-mower
9 KEY-woodruff
10
11
12 WASHER-lock, 7/16
13 WASHER-shoulder
14
15
16
17 WASHER-Hat, 5/16
18
19
ARBOR TUBE ASSEMBLY-center LM-16022-59
^ BEARING LM-01082-02
SPACER LM-16022-65
ARBOR ASSEMBLY
LM-16073-66
LM-01084-72 X
LM-16028-81LM-09250-84
LM-16076-38
SHEAVE-mower
LM-16076-37LM-09183-12 X
NUT-jam hex lock
SCREW-hex hd. cap, 7/16-20 x 1-1/2
LM-16070-21
LM-09280-66
LM-09181-99 X X
LM-16075-85
WASHER-Belleville
LM-16035-92
SCREW-hex hd. cap, 5/16-18 x 3/4 LM-09173-97
WASHER-lock, 5/16
LM-09173-56 X X
LM-09176-42
NUT-hex, 5/16-18
BLADE-mower (42”)
BLADE-mower (48”)
LM-09173-72
LM-16075-36
LM-16073-69
SIDE ARBOR & HOUSING LM-16075-84
Includes:
20
21
22
23 ARBOR ASSEMBLY
24 WASHER-special
25 SHEAVE-mower spindle
26 KEY-woodruff
27
28
29
30
31
32
33 WASHER-flat
34 WASHER-lock
35
36 LEVER ASSEMBLY-idler
37 WASHER-flat
38
39 PULLEY-idler
40
41
42
43 V-BELT ARBOR DRIVE
ARBOR TUBE ASSEMBLY LM-16022-59 X
BEARING f
SPACER
LM-01082-02
LM-16022-65 X X
LM-16073-67
LM-01084-72 X X
LM-16028-81
LM-09183-12
NUT-jam hex LM-16070-21
SCREW-hex cap, 7/16-20 x 1-1/2 LM-09280-66
WASHER-lock, 7/16
WASHER-shoulder
WASHER-belleville
STUD
LM-09181-99
LM-16075-85 X X
LM-16035-92
LM-16041-37 X
LM-09226-11
LM-09169-65
NUT-hex LM-09169-50
LM-16030-88 X
LM-09249-40
NUT-hex lock LM-09180-06
LM-16035-15 X X
SPACER
SCREW-hex hd. cap, 3/8-16 x 1-3/4
SPRING
LM-16104-04 X X
LM-09193-61
LM-16015-13 X X
LM-16030-77 X
V-BELT ARBOR DRIVE LM-16030-75
44
CLIP-spring LM-16030-90
45
BELT-front, PTO drive LM-16072-84
BELT-front. PTO drive LM-01085-08
ALWAYS FURNISH MODEL AND SERIAL NUMBER WHEN ORDERING PARTS.
X
X
X X
X X
X X
X X
X X
X X
X X
X X
X X
X X
X X
X
X
X X
X X
X X
X X
X
X X
X X
X X
X X
X X
X X
X X
X
X X
X X
X X
X
00
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Qtj
1
1
1
2
1
1
2
1
1
1
1
2
1
1
1
1
1
18
18
18
18
3
3
2
2
4
2
2
4
2
2
2
2
2
2
2
1
2
2
2
1
4
1
1
1
1
, 1
1
1
1
1
1
Mower Housing
ALWAYS FURNISH MODEL AND SERIAL NUMBER WHEN ORDERING PARTS.
No.
Description
Part No.
00
(M
Qty.
No. Description
Part No.
Qty.
1 GUIDE-belt (R. H.)
GUIDE-belt, (L. H.)
2
BOLT-rd.hd., 5/16-18x3/4
3
WASHER-flat, 5/16
4
WASHER-lock
5
NUT-hex, 5/lp x 18
6
LEG ASSEMBLY-arbor cover (outer)
7
LEG ASSEMBLY-arbor cover (inner)
8
>
>
<
'J)
Tl
C
33
s
c/>
X
o
u
m
>
□
C/5
m
>
1”
Z
c
COVER-arbor (R. H.)
9
WASHER- flat
10
WASHER-lock
11
NUT-hex
12
COVER-arbor (L. H:)
13
HOOK-mower lift
14
WASHER-flat
15
WASHER-lock
16
17 NUT-hex
CABLE ASSEMBLY-lift
18
PIN-cotter
19
GUARD ASSEMBLY-discharge
20
GUARD ASSEMBLY-discharge
21
BOLT-round head
LM-16042-80
X X
LM-16042-79 X X
LM-09194-14 X X
10
LM-09176-42 X X 8
LM-09173-56 X X
10
LM-09173-72 X X 10
LM-16042-77 X X
LM-16042-78
X
X 4
LM-16042-75 X X
LM-09182-64
LM-09169-64 X
LM-09166-22
X 6
X
X 14
X X 14
LM-16042-74 X X
LM-16064-93 X X
LM-09184-30 X
LM-09181-99 X
LM-09182-13
LM-16064-73
X
X
X X 2
X X
LM-09184-52 X X
LM-16033-62
X
LM-16033-65 X
LM-09221-10 X X
1
1
2
1
1
1
1
1
1
1
1
1
1
WASHER-lock
22
23 NUT-hex
CLIP-baffle
24
BOLT-rd.hd.
25
SCREW-hex hd. cap
26
WASHER-flat
27
28
HOUSING-mower (42")
HOUSING-mower (48")
BAFFLE-mower (42")
29
BAFFLE-mower (48')
BOLT-rd.hd., 3/8-16 x 1
30
BOLT-rd. hd.
LM-09109-65 X X
LM-09169-50 X X
LM-16015-58 X X 4
LM-09169-43 X X 4
LM-09077-27 X X 4
LM-09173-77 X X
LM-16028-38 X
LM-16028-78 X
LM-16032-68
LM-16033-6S X
LM-09232-32 X
LM-09221-10 X 2
Accessories
TRANSFER-patent
TRANSFER-caution
LM-16019-19 X X
LM-01749-36 X X
DECAL-quadrant LM-16075-19 X X
PAINT-blue, 14 oz. spray can
PAINT-black, 12 oz. spray can
DECAL- OPEI
LM-16076-89 X X
22772
LM-01729-80 X X
X
X X
3
3
4
1
1
1
1
2
1
2
1
1
1
1
Roller Assembly
M
/
No. Description
1
SHAFT ASSEMBLY-roller LM-16076-14 X 1
Part No.
SHAFT ASSEMBLY-roller LM-16076-07
2
ROLLER ASSEMBLY-long LM-16029-48
ROLLER ASSEMBLY-long
LM-16029-48 X 5
Includes:
3 BUSHING
LM-01084-19 X 6
BUSHING LM-01084-19
4 ROLLER ASSEMBLY-short
ROLLER ASSEMBLY-short
LJ&-01084-31 X 3
LM-01084-31 X
Includes:
5 BUSHING LM-01084-19
BUSHING LM-01084-19
6 SPACER-roller
7 WASHER-flat
8 PIN-cotter, 3/16 X 1
9 BRACKET-center roller
10
BOLT-rd.hd., 5/16-18x1
11 LOCKWASHER-5/16
12
NUT-hex, 5/16-18
13
SHAFT ASSEMBLY-center roller LM-16033-09
LM-16029-46 X X 6
LM-09193-87
LM-09184-58 X X 2
LM-16032-69 X X
LM-09189-95 X
LM-09173-56
LM-09173-72 X X 4
CO
(N!
Qty
X
X 3
X
X 6
X
X 11
X
X
X X 4
X X
1
10
1
2
1
4
1
ALWAYS FURNISH MODEL AND SERIAL NUMBER WHEN ORDERING PARTS.
Hitch Assembly
V—12
No.
1
2
3
4
5
ä
7
8
9
10
11
12
13
14
15 BOLT-shoulder
16
17 : BRACKET-front (L.H.) LM-16029-42 1
18 ERACKET-front (R. H.) LM-16029-43 1
Description Part No.
ARM ASSEMBLY-mower
BRACKET-pivot (L. H.) LM-16032-59 1
QUADRA NT-mower control
BOLT-rd.M., 3/8-16x3/4
WASHER-lock. 3/8 LM-09169-65 21
NUT-hex, 3/8-16
LEVER- control LM-16074-14 1
PEN-eotter, 1/8 x 1
SPRING-mower quadrant LM-16032-62 1
RIVET-pop
"E" RING
KNOB
BRACKET-roller support LM-16032-64 2
EAR-roller
WASHER-flat, 7/16 LM-09184-30 4
ALWAYS FURNISH MODEL AND SERIAL NUMBER WHEN ORDERING PARTS.
LM-16065-32 1
LM-16032-60 1
LM-09221-10 15
LM-09169-50 21
LM-09184-52 4
LM-16020-93 2
LM-09277-94
LM-16102-53 1
LM-16032-63
LM-16021-86 4
Qty.
No.
19
20
21
22 WASHER-nat
23 ROD-adjusting (R. H.) 42" Mower
24
25
26 PIN-yoke, 1/2
1
27 PIN-quick
28
29
1
30
31
Description
SPACER-pivot
LINK ASSEMBLY-mower
SCREW-hex hd. cap, 3/8-16 x 1-3/4
ROD-adjusting (R. H.) 48" Mower
ROD-adjusting (L. H.) 42" Mower
ROD-adjusting (L, H.) 48" Mower
YOKE-rod end adjusting
NUT-jam hex. 1/2-20
WASHER-flat, 25/32 x 1-1/8
SUPPORT-shaft (L. H.)
SUPPORT-shaft (R.H.)
PIN-rd.hd.
Part No.
LM-16032-70
LM-16070-79
LM-09193-61
LM-09227-55
LM-16032-56
LM-16033-66
LM-16032-57
LM-16033-67
LM-01576-31
LM-09192-62
LM-01543-05
LM-09181-96
LM-09243-68
LM-16070-53
LM-16070-52
LM-01563-06
Qty.
2
1
2
2
1
1
1
1
2
2
2
4
1
1
1
2
Attaching Rotary Momr
Remove contents from carton. The height adjustment
control lever is taped to the adjusting rod. Remove the
lever and proceed as follows;
1. Apply a light coat of grease to the control lever.
2. Pass the lever down through the quadrant, behind the
spring, and secure to roller shaft with the two cotter pins
supplied (see photo).
7 Attach one end of the lift cable to the lift shaft located on
the underside of the unit. Route the cable over and onto the
small idler pulley and secure the other end to the "L" shaped
stud on top of the mower deck using a cotter pin. NOTE: Be
sure lift is all the way in the down position.
NOTE: THE FOLLOWING STEPS ARE AS IF YOU ARE
FACING THE FRONT OF THE UNIT.
3. Pull the drive belt toward the front of the mower
housing and keeping it tight, adjust the belt stops on the
mower deck to within 1/8 in. of the belt.
4. Park the unit on aflat level surface and slide the mower
under the unit from the right side.
5. Raise the front of the mower housing and support it
using a block of wood.
1. Pull the belt between the two idler pulleys.
2. Unlatch and raise the hood.
3. Loosen the two nuts securing the right idler pulley and back
off on the adjusting screw on front of the PTO bracket, releasing
the pulley.
4. Place the belt in the right pulley, the belt may have to be
twisted 90° clockwise.
5. Route the belt up through the frame, around the engine
pulley and back down to the left idler pulley.
6. Pull the black, tension release knob forward and secure the
drive belt around the pulley.
7. Looking straight down at the pulleys, turn the adjusting
screw clockwise, until both pulleys are lined up. (see
illustration).
6. Secure mower link bracket to the rear holes in the
hitch extension (on the frame) with the clevis pin and
quick pin.
10
/
8. Tighten the two nuts securely.
NOTE: Due to belt wear, periodically check alignment of
pulleys. This will keep proper tension on the belt and
prevent any slipage.
Mower Adjustments
Loosen the locknut on the adjusting rods. Remove the quick
pin and clevis pin from each clevis. Rotate each clevis the same
amount of turns to obtain a height of 1/8" to 1/4" higher at
point "A” than point "B".
NOTE: To raise the front of the mower, turn the clevis
clockvi/ise. Be sure to recheck point "B" after
obtaining proper height at point "A".
CAUTION: Remove key and disconnect spark plug wire
before making the following adjustments.
For proper grass cutting, the Rotary Mowers must be set so the
front of the blade is approximately 1/8" to 1/4" higher than
the rear. Proceed as follows:
1. Park the unit on a flat level surface. Place the cutting height
lever in the uppermost position.
2. Measure the distance at point "A" and point "B". if point
"A" is not 1/8" to 1/4" higher than point "B" proceed as
follows:
Every mower must be checked and adjusted in accordance
with the above instructions prior to operation of the
unit.
REPLACEMENT PARTS
Replacement parts for your HOMELITE equipment should be
purchased from your HOMELITE Dealer. 'Be prepared to give
him the tractor name, model, and the serial number.
USE ONLY HOMELITE BELTS AND BLADES.
CAUTION: Always check mower for broken parts immediately
after striking any solid object. If a blade is bent, it should be
replaced rather than straightened and reused. Any broken
parts should be replaced. Replacement blades should be
ordered only from your HOMELITE dealer.
11
Part No.
Description
Qty.
Part No. Description Qty.
22772
LM 01010
LM 01082
LM 01084
LM 01084
LM 01085
LM 01543
LM 01563
LM 01576
LM 01729
LM 01737 47 Spring- extens ion
LM 01749
LM 09160 01 Pin-spring
LM 09183
LM 09277 94
LM 16010
LM 1601S
LM 16015
LM 16019
LM 16020
LM 16022
LM 16022 65
LM 16028
LM 16028 78
LM 16028
LM 16029
LM 16029
LM 16029 46 Spacer-roller
LM 16029 48 Roller Assembly
LM 16030
LM 16030 77
LM 16030
LM 16030
LM 16032
LM 16032
LM 16032 59 Bracket-pivot
LM 16032
LM 16032
LM 16032
LM 16032
LM 16032
LM 16032 69
LM 16032
LM 16033
LM 16033
LM 16033
LM 16033
LM 16033
LM 16033
LM 16035
LM 16041
LM 16042 74 Cover-arbor
LM 16042
LM 16042
LM 16042
LM 16042 79
LM 16042
LM 16064
LM 16064
LM 16065 32 Arm Assembly
LM 16070 52 Support-shaft
LM 16070
LM 16070 56 Clevis Assembly
LM 16070
LM 16070
LM 16070 64
LM 16070
Paint-black, 12 oz.
96 Pulley“ idler
02 Bearing-ball
19
Bushing
31 Roller Assembly
08 Belt-front
05 Pin-yoke
06 Pin-3/S X 1-1/2
31 Yoke-rod end
80 Decal-safety
36
Film-caution
12
Key-woodruff
"E" Ring-retaining
42
Knob-ball
13
Spring
58 Clip-baffle
19 Trans fer-patent
93 Rivet-pop
59
Arbor îhbe
Spacer
Housing-42" mower 1
38
Housmg~48" mower 1
81
Sheave-mower
42 Bracket-front
43 Bracket-front
75
"V" Belt
"V'Belt
88
Lever Assembly
90 Clip-spring
56
Rod-adjusting
57 Rod-adjusting
60 Quadrant
62
Spring
63 Bar-roller
64
Bracket-roller
68 Baffle-42" mower
Bracket-roller
70
Spacer-pivot
09
Shaft Assembly
62
Guard Assembly
65 Guard Assembly
66
Rod-ad jus ting
67
Rod- adjusting
68
Baffle
15
Pulley-idler
37
Stud
75
Cover-arbor
77
Leg Assembly
78
Leg Assembly
Guide-belt (L. H.).
80
Guide-belt (R. H.)
73
Cable Assembly
93
Hook-mower lift
53 Support-shaft
60
Bracket Assembly
61
Plate-reinforce ment 1
Support Assembly
66
Arm Assembly
2
6
14 LM 16073 66
3
1
2
4
2
1
1
2
2
4
1
1
1
4
1
2
3
3
3
1
1
6
5
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
.1
2
4
1
1
1
1
1
1
1
1
1
1
1
LM 16070 73 Bracket Assembly
LM 16070 79
LM 16072 84
LM 16073 67 Arbor Assembly
LM 16073 69
LM 16074 14 Lever-control
LM 16075 19 Decal-quadrant
LM 16075 36
LM 16075 82 Center Arbor-42"
LM 16075 83
LM 16075 84
LM 16076 07 Shaft Assembly
LM 16076 14
LM 16076 37
LM 16076 38
LM 16076 89
LM 16102 53
LM 16104 04
LM 16104 56
FASTENING PARTS
LM 01084 72 Washer-special
LM 01591 34 Washer-special
LM 09077 27
LM 09166 22
LM 09169 43 Bolt-carriage
LM 09169 50
LM 09169 60
LM 09169 64
LM 09169 65
LM 09173 56
LM 09173 72
LM 09173 77
LM 09173 97
LM 09174 00
LM 09176 42
LM 09180 06
LM 09181 96
LM 09181 99
LM 09182 13 Nut-7/lG-14
LM 09182 64
LM 09184 30
LM 09184 52
LM 09184 58
LM 09189 95 Bolt-5/16-18 X 1
LM 09192 62
LM 09193 57 3/8-16 X 7/8
LM 09193 60 3/8-16 X 1-1/2 2
LM 09193 61
LM 09193 87 Washer-flat 13
LM 09194 14
LM 09211 58
LM 09221 10 Bolt-3/8-16 X 3/4 18
LM 09226 11
LM 09227 55 Washer-flat 2
LM 09232 32 Bolt-3/8-16 X 1 2
LM 09234 23 5/16-18 X 2-1/2
LM 09234 28
LM 09243 68
LM 09249 40
LM 09250 84 Washer-Rat
LM 09280 66 7/16-20 X 1-1/2 3
LM 16021 86
LM 16035 92
LM 16070 21 Nut-3/4-16
LM 16071 24
LM 16075 85 Washer-shoulder
Link Assembly
Belt-front
Arbor Assembly
Blade- 48" mower
Blade-mower 42"
Center Arbor- 48"
Side Arbor
Shaft Assembly
Sheave
Sheave
Paint-blue, 14 oz.
Knob-ball
Spacer
Bushing
1/4-20 X 5/S
Nut-1/4-20
Nut-3/8-16
Washer
Washer-1/4 14
Washer-3/8 30
Washer-5/16 35
Nut-hex, 5/16-18
Washer-flat, 1/4 4
5/16-18 X 3/4
3/8-16 X 1-1/4
Washer-5/16 27
Nut-3/8-16
Pin-quick
Washer-7/16 4
Washer-1/4 6
Washer-7/16 5
Pin-cotter, 1/8 X 1
Pin-cotter
Nut-1/2-20
3/8-16 X 1-3/4
Bolt-5/16-18 X 3/4 10
Bolt-5/lG-18 X 1
Washer-flat. 2
Nut-3/8-16
Washer-Rat
Washer
Bolt-shoulder
Washer
Screw-cap
2
1
1
1
2
3
1
1
1
1
1
2
1
1
1
1
1
1
2
6
2
4
14
4
29
2
34
18
1
O
1
6
2
8
2
4
2
1
3
1
1
1
1
10
1
4
3
3
1
3
PRINTED IN U. S. A.
» tflxtroni
PORT CHESTER, NEW YORK, U.S.A. 10573
DIVISION
E1275EZ
Loading...