Hitachi P50H401A, P55H401, P42H4011, P50H401, P42H401 User Manual

PLASMA TELEVISION

SPANISH

Operating Guide for P42H401, P42H401A P50H401, P50H401A, P55H401, P42H4011

P42H4011A, P50H4011, P50H4011A and P55H4011

IMPORTANT SAFETY INSTRUCTIONS .................................................................................................................. 2-3

FIRST TIME USE .................................................................................................................................................... 4-22

THE REMOTE CONTROL ..................................................................................................................................... 23-31

ON-SCREEN DISPLAY ......................................................................................................................................... 32-54

USEFUL INFORMATION ...................................................................................................................................... 55-64

OPERATING GUIDE IN SPANISH ...................................................................................................................... 65-128

END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE .......................................................... 129-137

APPENDIXES ................................................................................................................................................... 138-139

INDEX ....................................................................................................................................................................... 140

Important Safety Instructions

SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI PLASMA TELEVISION

Our reputation has been built on the quality, performance, and ease of service of HITACHI plasma televisions.

Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI plasma television.

Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the improbable event that a safety problem should be discovered in your product model.

Follow all warnings and instructions marked on this plasma television.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended

to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to a person.

The exclamation point within an equilateral

triangle, is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the literature accompanying the appliance.

READ BEFORE OPERATING EQUIPMENT

Follow all warnings and instructions marked on this plasma television.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use the attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod,

bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.

Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.Televisions are designed to comply with the

recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury.

16.Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.

17. An outdoor antenna should not be located in the vicinity of overhead power lines or other electrical circuits.

18. If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding for the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of

grounding connectors, location of antenna discharge unit, connection to grounding electrodes and

requirements for the grounding electrode.

NEC National Electric Code

Note to the CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-44 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Important Safety Instructions

Public viewing of copyrighted material

Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require prior authorization from the broadcaster or owner of the video program material.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized, and is intended for home and other limited consumer uses only unless otherwise authorized. Reverse

If still images are left on the screen for more than 2.5 minutes, protection function will work automatically so that contrast reduces to minimize image retention on plasma display panel.

Please note that this is not a malfunction but it helps to minimize image retention. The original contrast will restore after moving images are displayed for about 6 minutes. Original contrast can be

Power source

This plasma television is designed to operate on 120 volts 60 Hz, AC current. Insert the power cord into a 120 volt 60 Hz outlet. The mains plug is used as the disconnect device and shall remain readily operable.

To prevent electric shock, do not use the plasma television’s (polarized) plug with an extension cord, receptacle, or other outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.

Never connect the plasma television to 50 Hz, direct current, or anything other than the specified voltage.

Caution

Never remove the back cover of the plasma television as this can expose you to very high voltages and other hazards. If

the television does not operate properly, unplug the plasma television and call your authorized dealer or service center.

Caution

Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by HITACHI could void the user’s

warranty.

Warning

• To reduce the risk of fire or electric shock, do not

expose this apparatus to rain or moisture.

• The plasma television should not be exposed to

dripping or splashing and objects filled with liquids, such as vases, should not be placed on the television.

• This apparatus shall be connected to a mains

socket outlet with a protective earthing connection.

engineering or disassembly is prohibited.

Note

This digital television is capable of receiving analog basic, digital basic cable television programming by direct connection to a cable system providing such programming. Certain advanced and interactive digital cable services such as video-on-demand, a cable operator’s enhanced program guide and data-enhanced television services may require the use of a set-top box. For more information call your local cable company.

Note

• There are no user serviceable parts inside the

plasma television.

• Model and serial numbers are indicated on back side

and right side of the plasma television.

Prevention of screen damages

Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed (non-moving) patterns can be permanently imprinted onto your TV screen. Such “SCREEN DAMAGES” constitute misuse and are NOT COVERED by your HITACHI Factory Warranty.

restored quickly by turning power Off/On with remote control or power switch on unit.

Lead Notice

This product contains lead. Dispose of this product in accordance with applicable environmental laws. For

product recycling and disposal information, contact your local government agency or www.eRecycle.org (in California), the Electronic Industries Alliance at www.eiae.org (in the US) or the Electronic Product Stewardship Canada at www.epsc.ca (in Canada).

FOR MORE INFORMATION, CALL 1-800-HITACHI.

Accessories

Check to make sure you have the following accessories before disposing of the packing material.

쐃

Remote Control

First time use

쐇쐏

Two “AA” size,

1.5V batteries

Table Top Stand

쐋

(50" included)

Power Cord

쐄

Wire Clamp

(50" models only)

쐋

Table Top Stand

(42” included)

For U.S. models:

For optional accessories, please access our web site at: www.hitachi.us/tv

Note : The accessories for models H4011, H4011A series are similar as the H401, H401A series.

CAUTION: 1. Ceiling mounting is not recommended. Mounting the panel on the ceiling does not

provide adequate ventilation for the electronics or proper support for the front glass panel. This plasma television product is designed for a maximum tilting angle of 45

degrees from vertical.

2. This stand for use only with Hitachi P42H401, P42H401A, P50H401 and P50H401A models. The use of other apparatus is capable of resulting in instability

causing possible injury.

3. The wall mount unit for the 50" and 42" models is WM07S and for the 55" models is WM07L. Please see page 7 for important information related to the wall mount. Wall Mount unit is an optional accessory (Not Included).

쐃 Remote Control Unit CLU-4371UG2 (Part No HL02075 only H401 series)

Remote Control Unit CLU-4372UG2 (Part No HL02076 only H4011 series)

쐇 Two "AA" size, 1.5V batteries . 쐋 Table Top Stand (UX27661 42" model)

(UX27281 50" models).

쐏 Power Cord (P# EV01841).

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

Open the battery cover of the remote control by pushing down and sliding the back cover off.

Insert two new “AA” size batteries for the remote contr springs and lift them out.

3. Match the batteries to the (+) and (-) marks in the battery compartment.

Insert the bottom of the battery compartment first, push towards the springs and insert the top of the battery battery into the battery compartment.

5. Replace the cover.

CAUTION: Do not insert batteries with ‘+’ and ‘-’ polarities reversed as this may cause the batteries to swell or rupture resulting in leakage.

, the (+) side, into place. Do not for

, the (-) side, into th e battery

ol. When r

ce the

eplacing old batteries, push them towards the

Bottom View (Remote Control)

Lift up on tab to r

Note: Please visit our website for optional accessories.

쐄 Wire Clamp (50" models only)

emo ve back cover.

How To Set Up Your New Hitachi Plasma Television

To take measures to prevent the Plasma Television from tipping over and prevent possible injury it is important to mount the unit in a stable and flat surface.

Securing to a table-top

1. Using wood screws (two) fasten the set to the clamping screw holes on the rear of the Plasma

TV stand as shown below.

2. Using commercially available wood screws, secure the set firmly in position.

Wire

55”

Wood screw two places

Securing to a Wall

1. Keep the Plasma television 4 inches away from the wall except when mounted using the wall mount bracket.

2. Secure the television to the wall as shown.

42"

4 in.

10 cm

50"

4 in.

10 cm

55"

4 in.

10 cm

* Please adjust the wire length to avoid touching the wall when turning the TV.

NOTES: 1. Do not block the ventilation holes of the

Plasma Television. Blocking the ventilation holes might cause fire or defect.

2. In case of an abnormal symptom, unplug the AC cord.

3. If you purchased the wall mount bracket

option, please ask for professional installer. Do not install by yourself.

4. Install the unit at a proper area where it does

not expose anyone to any danger of hitting

themselves (for example their hands, head

or face, etc.) against the edge of the unit and cause personal injury.

NOTE: The Table Top Stand for model P55H401 and

P55H4011 is not included (Optional).

ANTENNA

Unless your Plasma Television is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient.

LOCATION

Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. In order to prevent an internal temperature increase, maintain a space of 10 cm (4 inches) from the sides/back of the Television, and 30 cm (12 inches) from the top of the television to the wall. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.

First time use

Caution when moving the main unit

As this product is heavy, whenever it is moved, two

people are required to transport it safely. Whenever the

unit is moved it should be lifted forward using the top and base on both sides of the Television for stability.

When moving the Television, lift the handles , then support the top frame as shown below.

42” 50”

10 cm (4 inches)

30 cm (12 inches)

10 cm (4 inches)

How to set up your new HITACHI Plasma Television

AC CORD INSTALLATION INSTRUCTION

The AC cord provided with your new Plasma Television needs to be installed correctly to avoid the AC cord from disconnecting when rotating the TV on its Table top stand. Located on the back of the TV are 2 plastic clamps to hold the AC cord. Please follow the

instructions below.

쐃

Pass the AC cord through Clamp #1 and connect

it to the TV. Pull on the clamp to tighten the

AC cord to the TV.

쐇

First time use

The AC cord and the signal cables can all be held together with Clamp #2.

쐋

Depend on the model size 42",50" or 55", the clamp may be different shapes. Only for 50" models the clamp #2 will be included on the accessories bag.

Clamp #1 : Pass the AC cord through this clamp ;

쐃

then pull the clamp to tighten the AC cord to the TV.

Clamp #2: Use this clamp to hold the AC cord and

쐇

the signal cables. For 50 " model please

assemble this Clamp on the middle hole of the base metal.

AC CORD

How to set up your new HITACHI Plasma Television

SETTING FOR WALL MOUNTING ON 50" & 55" MODELS

STEP (1) :

Please locate the STAND METAL on the back of the TV . This metal is use to hold the TV and the Base ; so it needs to remove 4 screws from the STAND base in order to separate the TV from the Base.

STAND METAL

STEP (2):

Please remove the 4 screws of the STAND metal from the TV, now the TV STAND can be separated from the TV. For dimensions of the WALL MOUNT assembly please refer to page 61 & 62.

First time use

4 SCREWS

STAND METAL

TV STAND BASE

For Model P50H401, P50H401A, P50H4011 and P50H4011A

CAUTION- This Plasma Display Panel for use only with Hitachi WM07S Wall Mount. Use with other

Wall Mount is capable of resulting in instability causing possible injury.

For Model P55H401 and P55H4011

CAUTION- This Plasma Display Panel for use only with Hitachi WM07L Wall Mount. Use with other

Wall Mount is capable of resulting in instability causing possible injury.

NOTE: Use the specified WALL MOUNT unit for the Plasma TV depending on the size of your TV.

Please access our web site at: www.hitachi.us/tv for recommended accessories for your tv.

How to set up your new HITACHI Plasma Television

SETTING FOR WALL MOUNTING ON 42" MODELS

STEP (1) :

Please locate the STAND METAL on the back of the TV . This metal is use to hold the TV and the Base ; so it needs to remove 6 screws from the STAND base in order to separate the TV from the Base.

First time use

STAND METAL

STEP (2):

Please remove the 2 screws of the STAND metal from the TV, then remove 4 screws that hold the TV STAND BASE; now the TV STAND can be separated from the TV.For dimensions of the WALL MOUNT assembly please refer to page 60.

2 SCREWS

STAND METAL

Remove these 2 screws

first to separate the TV

rom the stand metal.

Then put these 2 screws

back to the TV.

Remove these 4 screws

to separate the TV from

TV STAND BASE

the stand base.

For Model P42H401, P42H401A, P42H4011 and P42H4011A

CAUTION- This Plasma Display Panel for use only with Hitachi WM07S Wall Mount. Use with other

Wall Mount is capable of resulting in instability causing possible injury.

NOTE: Use the specified WALL MOUNT base for the Plasma TV depending on the size of your TV.

Please access our web site at: www.hitachi.us/tv for recommended accessories for your tv.

How to set up your new HITACHI Plasma Television

VIEWING

The best picture is seen by sitting directly in front of the TV and about 10 to 18 feet from the screen.

During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the TV can be located in a different section of the room.

If the TV’s audio output will be connected to a Hi-Fi system’s external speakers, the best audio performance will be obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround speakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker placement for best performance.

4" Minimum

BEST HORIZONTAL

10'

VIEWING ANGLE

15' 20'

First time use

ANTENNA CONNECTIONS TO REAR JACK PANEL

VHF (75-Ohm) antenna/CATV (Cable TV)

When using a 75-Ohm coaxial cable system, connect CATV coaxial cable to the AIR/CABLE (75-Ohm) terminal. Or if you have an antenna, connect the coaxial cable to the same AIR/CABLE terminal.

AIR / CABLE

To CATV cable

VHF (300-Ohm) antenna/UHF antenna

When using a 300-Ohm twin lead from an outdoor

antenna, connect the VHF or UHF antenna leads to screws of the VHF or UHF adapter. Plug the adapter

To outdoor antenna

into the antenna terminal on the TV.

AIR / CABLE

When both VHF and UHF antennas are connected

Attach an optional antenna cable mixer to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your dealer or service store for the antenna mixer.

To UHF antenna

AIR / CABLE

To outdoor VHF or UHF antenna

To outdoor antenna or CATV system

Antenna Mixer

NOTE: Connecting a 300-Ohm twin lead connector may cause interference. Using a 75-Ohm coaxial

cable is recommended.

Hook-up Cables and Connectors

Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output and input connector types required by the various components and the length of each cable.

300-Ohm Twin Lead

Cable

This outdoor antenna cable must be connected to an antenna adapter (300-Ohm to 75-Ohm).

Phono or RCA

Cable

Used on all standard video and audio cables which

First time use

connect to inputs and outputs located on the

television’s rear jack panel and front control panel.

“F” Type 75-Ohm Coaxial Antenna

For connecting RF signals (antenna or cable TV) to the antenna jack on the television.

S-Video (Super Video)

Cable

This connector is used on camcorders, VCRs and laserdisc players with an S-Video feature in place of the standard video cable to produce a high quality picture.

Optical Cable

This cable is used to connect to an audio amplifier with an Optical Audio In jack. Use this cable for the best sound quality.

HDMI Cable

This cable is used to connect your external devices such as Set-Top-Boxes or DVD players equipped with an HDMI output connection to the TV’s HDMI input.

Stereo Cable (3.8mm plug to 3.5mm plug)

Used on all standard video and audio cable which connect to inputs and outputs located on the rear jack

panel and front control panel.

AUDIO OUT

3.8mm STEREO MINI-PLUG

2 RCA TYPE PLUGS

Quick Reference Remote Control Buttons and Functions

In addition to controlling all of the functions on your HITACHI Plasma TV, the new remote control is

designed to operate different types of devices, such as, DVD Players, CBL (Cable Boxes), set-top-boxes, satellite

receivers, and VCRs. The remote control must be programmed to control the chosen device. Please see pages 2331 for a complete description of all features and programming of the Remote Control.

(TV, CBL, VCR, DVD, SAT)

POWER BUTTON

Turns the selected device on

and off.

INPUTS BUTTON (TV)

Accesses the INPUTS menu

system.

ASPECT BUTTON (TV)

Changes the aspect ratio while

watching TV.

MENU BUTTON

(CBL, DVD, SAT, TV)

Accesses the OSD menu

system.

CURSOR/SELECT BUTTONS

(TV, DVD, CBL, SAT)

The CURSOR buttons are used

to navigate the cursor through

the OSD and INPUTS menu

systems, and the SELECT

button is used to

Select/Activate the highlighted

menu item.

VOLUME BUTTONS (TV)

Adjusts the audio level of your

TV.

MUTE BUTTON (TV)

Reduces the audio level to 50%

if pressed once, and to

complete mute if pressed twice.

Press it a third time to restore

audio level.

NUMERIC BUTTONS

(TV, DVD, CBL, SAT, VCR)

Used to manually enter the TV

channel, and used for numeric

entry when navigating through

the OSD menu system.

(-) BUTTON (TV, SAT)

The (-) button is used when the remote is in Set-Top-Box (STB)

mode or when the TV uses a

digital input.

SOURCE ACCESS BUTTONS (TV, DVD, VCR, CBL, SAT)

Changes the mode of the Universal Remote Control to control the device selected.

DAY/NIGHT BUTTON (TV)

Select picture mode settings between DAY and NIGHT mode.

CC BUTTON (TV)

Press to show and change the Closed Caption mode.

EXIT BUTTON (TV, CBL, SAT)

Exits out of the OSD or INPUTS menu systems if their menu is displayed.

FAVORITE CHANNEL (FAV CH) button (TV)

Press to enter/access Favorite Channel (FAV) mode.

GUIDE BUTTON (SAT/STB, CBL)

Accesses the program guide of other devices.

INFO BUTTON (TV, CBL, SAT)

Displays various information on the screen.

CHANNEL BUTTONS (TV, CBL, SAT, VCR)

Changes the channel.

LAST CHANNEL (LC) BUTTON (TV, CBL, SAT)

Switches between the current and last channel viewed.

DVD/VCR CONTROL BUTTONS (DVD, VCR)

Controls the precode functions of your VCR and DVD.

First time use

RECORD BUTTON (VCR)

Press twice (2 times) to record

programs.

LEGEND TV — Television VCR — Video Cassette Recorder/Player

SAT — Satellite Receiver

CBL — Cable Box DVD — Digital Video Disc Player

NOTES: 1. The TV’s remote control sensor is located on the right bottom portion of the TV screen. To

control TV functions, please point the remote control directly at the remote control sensor for best results.

Front Panel Controls

FRONT VIEW

First time use

햺

햻

PUSH TO OPEN CONTROL DOOR

UPGRADE CARD

(SERVICE USE ONLY)

PUSH EJECT

햸

FRONT PANEL CONTROLS

햹

햲 FRONT POWER button

Press this button to turn the Plasma Television ON/OFF. It can also be turned ON/OFF by remote control. The “MAIN POWER” button must be at stand-by mode.

햳 MENU/SELECT button

This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode.

햴

HDMI-FRONT

Use the front HDMI input for extrenal devices such as Set-Top-Boxes or DVD players equipped with an HDMI output connection (see page 15 for reference).

햵 INPUT/EXIT button

Press this button to access the INPUT menu. Press again to exit the MENU mode.

햶 CHANNEL selector

Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as the cursor down () and up () buttons when in MENU mode.

햷 VOLUME level

Press these buttons to adjust the sound level. The volume level will be displayed on the TV screen. These buttons also serve as the cursor left () and right () buttons when in MENU mode.

햴

햳

햷

햽

햸 POWER button

Television MAIN POWER button

This power button is for the complete system, and must be turned ON/OFF manually. It is recommended to leave the “MAIN POWER” to ON condition (lights red) for stand-by mode.

햵

햶

햲

The Main Power button is located on the broadside bottom, under the mark " ".

NOTE: When the “MAIN POWER” button is set to

OFF or the TV is unplugged, the clock will stop and may eventually reset itself.

햹

Upgrade Card

This card slot is for future software upgrades. Hitachi will notify you if a software upgrade is required for your TV. In order to receive written notification, please complete and return your warranty card.

Front Panel Controls

햺

POWER light indicator

To turn the TV ON, press the main power switch located on the lower right side of the TV. A red stand-by indicator lamp located on the lower right corner of the front bezel will illuminate. The Plasma TV is now ready for remote ON/OFF operation.

Indicating Lamp Power Status Operating

햺

Indicating Lamp

햻

R/C sensor

First time use

Off

Lights

Red

Lights

Blue

Lights

Orange

Blinking

Blue

햻

REMOTE CONTROL sensor

Point your remote at this area when selecting channels, adjusting volume, etc.

INPUT-FRONT JACKS

햽

INPUT-FRONT provide composite Video jacks for connecting equipment with this capability, such as a DVD player or Camcorders.

OFF. When the main power switch is set to Off.

OFF.

(Stand-by)

Off

(Power Saving)

When the main power switch on the TV is ON.

TV MAIN POWER is ON ; picture is shown.

TV MAIN POWER is ON with no signal input

except antenna (no sync. signal).

On When TV receives the IR signal from R/C.

NOTES: 1. Your HITACHI Plasma TV will appear to be turned OFF (lights orange) if there is no video input

when INPUT : 1, 2, 3, Front or HDMI : 1, 2, Front is selected. Check the Power Light to make sure the TV is turned off or in Stand-by mode (lights red) when not in use.

2. Remote Control can not turn ON/OFF the “MAIN POWER” of the TV.

Rear Panel Connections

햲 Antenna Input

To switch between Cable and Air input, go to the Channel Manager option to change the signal source CABLE or AIR.

햳 Audio/Video Inputs 1, 2 and 3

By using the INPUTS button, the CURSOR PAD ( and ), and the SELECT button or CURSOR PAD  of the remote control, you can select each video source. Use the audio and video inputs to connect

햶

햺 햹

햲

햴

external devices, such as VCRs, camcorders,

First time use

laserdisc players, DVD players etc. (if you have

햷

햳

mono sound, insert the audio cable into the left audio jack).

햴 MONITOR OUT & AUDIO OUT

These jacks provide fixed audio and video signals (CABLE/AIR or INPUTS ) which are used for recording. Use the S-VIDEO output for high quality video output. Component signal

햸

NOTE: 1. The HDMI input is not intended for use

with personal computers.

2. Only DTV formats such as 1080p, 1080i, 720p, 480i and 480p are available for HDMI input.

햵

to Input 2 and 3, and HDMI inputs will not have monitor output.

햵 Optical Out (Digital Audio)

This jack provides Digital Audio Output for your audio device that is Dolby

® Digital and PCM

compatible, such as an audio amplifier.

햸 Component: Y-P

INPUTS 2 and 3 provide Y-P

connecting equipment with this capability, such as a DVD player or Set Top Box. You may use composite video signal for both inputs.

NOTE: 1. Do not connect composite VIDEO and

BPR Inputs

BPR jacks for

S-VIDEO to INPUT 1 at the same time.

NOTE: *Manufactured under license from Dolby

Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

S-VIDEO has priority over VIDEO input.

2. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s P

input and the components R-Y output to

햶 S-VIDEO Input 1

Input 1 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.

NOTE: 1. You may use VIDEO or S-VIDEO inputs to

connect to INPUT 1 , but only one of these inputs may be used at a time.

2. S-VIDEO output may be used for recording, only when the input is of S-VIDEO type.

the TV’s P

3. Your component outputs may be labeled Y-C C

B output to the TV’s PB input and the

component C

4. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-P

5. To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPR jacks and HDMI

R input.

BCR. In this case, connect the component

R output to the TV’s PR input.

BPR inputs (see page 34).

Input.

햷 HDMI 1, 2 (High Definition Multimedia

Interface)

ABOUT HDMI – HDMI is the

6. INPUT 2 , and 3 (Y/VIDEO) can be used for composite video and component video input.

next-generation all digital interface for consumer electronics. HDMI enables the secure distribution of uncompressed high-definition video and multichannel audio in a single cable. Because digital

햹 For Special AV control use only. 햺 For Factory use only.

television (DTV) signals remain in digital format, HDMI assures that pristine high-definition images retain the highest video quality from the source all the way to your television screen.

Use the HDMI input for your external devices such as Set-Top-Boxes or DVD players equipped with an HDMI output connection.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.

Connecting External Video Sources

The FRONT panel jacks are provided as a convenience to allow you to easily connect HDMI or DVI signals from a DVD, Set Top Box , Video Game as shown in the following examples (When connecting DVI signal it will

need to connect the audio output into the Front Audio Input jacks) :

A) Connecting HDMI signal.

FRONT INPUT PANEL

UPGRADE CARD

(SERVICE USE ONLY)

PUSH EJECT

HDMI DIGITAL

OUTPUT CAPABILITY

DVD , Set Top Box,

Video Game Console.

B) Connecting DVI signal.

FRONT INPUT PANEL

First time use

Note : Special device cables will be

according to the own device specifications.

UPGRADE CARD

(SERVICE USE ONLY)

PUSH EJECT

DVI to HDMI

Cab le

Note : Special device cables will be

DIGIT AL O UT P UT

OUTPUT

L R

according to the own device specifications.

Back of HDTV Set-Top-Box or DVD Player

DVI DIGITAL

OUTPUT CAPABILITY

DVD , Set Top Box,

Video Game Console.

NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back

picture may be abnormal.

Connecting External Video Sources

The FRONT panel jacks are provided as a convenience to allow you to easily connect a camcorder , DVD, Video Game and a VCR as shown in the following examples:

FRONT INPUT PANEL

UPGRADE CARD

(SERVICE USE ONLY)

PUSH EJECT

First time use

Note : Special device cables will be

according to the own device

specifications.

Note : For Monoaural devices, please

connect Audio signal cable into L/Mono input jack .

OUTPUT

Video

L R

COMPOSITE VIDEO

Video Game

OUTPUT CAPABILITY

DVD , Video Game

Console.

Video Camera

NOTE:1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the

played back picture may be abnormal.

The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your Plasma TV is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs.

The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your particular assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded wire.

Before Operating External Video Source

Connect an external source to one of the INPUT terminals, then press the INPUTS button to show the

INPUTS menu. Use the CURSOR PAD ( and ) to select the Input of your choice. Then press the SELECT button or the CURSOR PAD  to confirm your choice (see page 26).

INPUTS

HDMI 2 HDMI-Front

Cable

Air /

Input 1 Input 2

Move SEL Sel.

Rear Panel Connections

VCR #2

V L R

S-VIDEO

INPUT

Optional

Outside Antenna

Cable TV coaxial cable

2-Way signal splitter

ANT IN

Optional

S-VIDEO

VCR #1

OUTPUT

VLR

First time use

HDMI

HDMI OUTPUT

HDMI DIGITAL

OUTPUT CAPABILITY

DVI

HDMI

DIGITAL OUTPUT

DIGITAL

OUTPUT CAPABILITY

AUDIO OUT

NOTE: Cables are optional, except when specified.

B/CBPR/CR

DVD Player

OUTPUT

L R

Y P

OUTPUT

HDTV Set-Top Box

L R

Tips on Rear Panel Connections

• S-VIDEO, Y-PBPR, or HDMI connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature.

• If your device has only one audio output (mono sound), connect it to the left audio jack on (L/(MONO)) the Rear Panel.

• Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.

• A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line

output (INPUT: 1 in the example on page 17). Refer to your VCR operating guide for more information on

First time use

line input-output connections.

• Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack.

• COMPONENT: Y-P DVD players and set-top-boxes. Use these connections in place of the standard video connection if your device has this feature.

• Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PBinput and the components R-Y output to the TV’s PRinput.

• Your component outputs may be labeled Y-C TV’s P

• It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPRinputs. (See

page 34).

• To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-P

HDMI input jacks.

• Input HDMI 1, HDMI 2 or HDMI FRONT can accept HDMI signal.

• S-VIDEO monitor output may be used for recording only when the input is of S-VIDEO type.

• When using a HDMI input from a Set-Top-Box, it is recommended to use a 1080p, 1080i or 720p input signal.

• When HDMI input a 1080p signal, it is recommended that the length of the cable should be less than 5 meters.

INSTALLATION RECOMMENDATION:

1. Video signals fed through a VCR may be affected by copyright protection systems and the picture will be distorted on the television.

2. Connecting the television directly to the Audio /Video output of a Set-Top-Box will assure a more normal picture.

input and the components CRoutput to the TV’s PRinput.

(Input 2 & 3) connections are provided for high performance components, such as

BPR

. In this case, connect the components CBoutput to the

BCR

BPR and

Connecting External Video Sources

CONNECTING A VIDEO AND STEREO AUDIO

SOURCE TO INPUT1 ~ INPUT-FRONT

1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT

Cable or Air signal

(VIDEO) jack, as shown on the Rear Panel to the right.

2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

4. Press the INPUTS button, then select INPUT 1 2,3 or Front from the INPUTS menu to view the program from the VCR or laserdisc player.

Back of

5. Select CABLE or AIR from the INPUTS menu to

VCR

Video

OUTPUT

return to the last channel tuned.

VCR

NOTE: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and

sound that is played back will be abnormal if the connection is loose.

2. A single VCR can be used for VCR #1 and VCR #2 (see page 17) but note that a VCR cannot record

its own video or line output. Refer to your VCR operating guide for more information on line inputoutput connections.

3. When INPUT 2 or 3 are used, it is necessary to connect the video output of the device to the Y/VIDEO input jack of the TV .

First time use

CONNECTING AN S-VIDEO AND STEREO AUDIO SOURCE TO INPUT 1

1. Connect the cable from the S-VIDEO OUT of the S-VHS VCR or the laserdisc player to the

Cable or Air signal

INPUT (S-VIDEO) jack, as shown on the Rear Panel to the right.

2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

4. Press the INPUTS button, then select INPUT 1 from the INPUTS menu to view the program from the VCR or laserdisc player.

5. Select CABLE or AIR from the INPUTS menu to return to the last channel tuned.

Back of VCR or

Laserdisc Player

Video L R

S-VIDEO

OUTPUT

VCR or Laserdisc Player

NOTE: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and

sound that is played back will be abnormal if the connection is loose.

2. A single VCR can be used for VCR #1 and VCR #2 (see page 17), but note that a VCR cannot record

its own video or line output. Refer to your VCR operating guide for more information on line inputoutput connections.

Connecting External Video Sources

CONNECTING A COMPONENT SOURCE WITH HDMI OR DVI CAPABILITY TO HDMI 1, HDMI 2 OR HDMI FRONT

NOTE: 1. Completely insert the connection cord

plugs when connecting to rear panel jacks. The picture and sound that is played back

1. Connect the HDMI or DVI to HDMI connection cable from the output of the HDTV set top box

or DVD player to the HDMI input as shown

on the Rear panel below.

2. With DVI output, connect the cable from the AUDIO OUT R of the HDTV set top box or DVD player to the INPUT (AUDIO/R) jack as shown on

First time use

the Rear Panel below.

3. With DVI output, connect the cable from the AUDIO OUT L of the HDTV set top box or DVD player to the INPUT (AUDIO/L) jack as shown on the Rear Panel below.

4. Press the INPUTS button, then select HDMI 1, 2 or FRONT to view the program from the HDTV SET TOP BOX or DVD player.

will be abnormal if the connection is loose.

2. The HDMI input on HDMI 1 , 2 and FRONT contains the copy protection system called High-bandwidth Digital Content Protection (HDCP). HDCP is a cryptographic system that encrypts video signals when using HDMI connections to prevent illegal

copying of video contents.

3. HDMI is not a “NETWORK” technology. It establishes a one-way point-to-point

connection for delivery of uncompressed video to a display.

The connected digital output device controls the HDMI interface so proper set-up of device user settings determines final

video appearance.

5. When using a DVI to HDMI cable, connect the Audio Out L and R cables at the same INPUT

5. Select CABLE or AIR from the INPUTS menu to return to the last channel viewed.

(1 , 2 or Front) as your HDMI INPUT(1 , 2 or Front). (For FRONT INPUT see page 15 for reference).

HDMI input

HDTV Set-Top-Box or DVD Player

DIGITAL OUTPUT

HDMI Cable

DVI to HDMI Input

HDTV Set-Top-Box or DVD Player

Back of HDTV Set-Top-Box or DVD Player

OUTPUT

Back of HDTV Set-Top-Box or DVD Player

DIGITAL OUTPUT

CABLE

Air signal

CABLE

Air signal

DVI to HDMI

Cable

+ 44 hidden pages