POWER TOOLS
TECHNICAL DATA
AND
SERVICE MANUAL
HAMMER
H 30PV
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
LIST No. E460
Jan. 2001
H
MODEL
H 30PV
Notice for use
Specifications and parts are subject to change for improvement.
Refer to Hitachi Power Tool Technical News for further information.
1. PRODUCT NAME .........................................................................................................................1
2. MARKETING OBJECTIVE ...........................................................................................................1
3. APPLICATIONS............................................................................................................................1
4. SELLING POINTS ........................................................................................................................1
4-1. Selling Point Descriptions ............................................................................................................. 2
5. SPECIFICATIONS ........................................................................................................................3
5-1. Optional Accessories .................................................................................................................... 4
6. COMPARISONS WITH SIMILAR PRODUCTS ............................................................................5
6-1. Specification Comparisons ........................................................................................................... 5
6-2. Demolishing Performance Comparisons ...................................................................................... 6
7. PRECAUTIONS IN SALES PROMOTION ...................................................................................6
7-1. Handling Instructions .................................................................................................................... 6
7-2. Caution Plate ................................................................................................................................ 6
7-3. Grease Replacement .................................................................................................................... 7
7-4. O-Ring Replacement .................................................................................................................... 7
8. REFERENCE INFORMATION ......................................................................................................8
8-1. Striking Operation ......................................................................................................................... 8
8-2. Idling-proof Mechanism................................................................................................................. 8
8-3. Sealed and Dustproof Construction .............................................................................................. 9
8-4. Tool Retainer ............................................................................................................................... 10
8-5. Adjusting Mechanism for Tool Swivel Angle ................................................................................ 10
9. REPAIR GUIDE .......................................................................................................................... 11
9-1. Precautions and Suggestions for Disassembly and Reassembly of Main Body..........................11
10. STANDARD REPAIR TIME (UNIT) SCHEDULES ...................................................................17
Assembly Diagram for H 30PV
CONTENTS
Page
--- 1 ---
1. PRODUCT NAME
Hitachi Electric Hammer, Model H 30PV
2. MARKETING OBJECTIVE
The Hitachi hammer Model H 30PV has been developed intended for faster and easier completion of light-duty
jobs such as stripping mortar and tiles and allows use of SDS-plus shank tools. Main specifications are as
follows:
(1) Easy-to-handle tool holder specially designed for single-step installation of the hammer bit
(2) Simple turning method, variable lock mechanism for easy working-angle adjustment of chisels, etc.
(3) A highly reliable mechanism for prevention of idle hammering results in prolonged service life.
3. APPLICATIONS
Stripping mortar and tiles.
Demolishing and chiseling of concrete.
Grooving and cutting of bricks
4. SELLING POINTS
A highly reliable mechanism for prevention of
idle hammering results in prolonged service life
Easy-to-handle tool holdr specially designed
for single-step installlation fo the hammer bit
Simple turning method, variable lock mechanism
for easy working-angle adjustment of chisels, etc.
Soft-touch grip for
easier handling
Maker • Model Weight Overall length
Hitachi H 30PV 4.2 kg (9.2 lbs.) 395 mm (15-9/16")
D 3.5 kg (7.7 lbs.) 350 mm (13-25/32")
C 3.5 kg (7.1 lbs.) 315 mm (18-3/8")
(Shown with optional cutter)
--- 2 ---
4-1. Selling Point Descriptions
4-1-1. A highly reliable mechanism for prevention of idle hammering results in prolonged service life
Conventional mechanism for prevention of idle hammering is to open and close the air holes according to the
movement of the striker. The Model H 30PV has air holes located at the position unaffected by the rebound of the
striker at no load. The air holes are opened and closed by the movement of the sleeve provided around the
cylinder that interlocks with the tool and the second hammer to prevent idle hammering. This mechanism
securely prevents idle hammering even in wall hammering works or even if a tool that can cause great rebound on
the striker such as a cutter is used. Thanks to the highly reliable mechanism for prevention of idle hammering, the
service life of the Model H 30PV is prolonged and hammering works requiring much attention not to break the
surroundings can be efficiently performed with the Model H 30PV.
4-1-2. Easy-to-handle tool holder specially designed for single-step installation of the hammer bit
The commercially available SDS-plus shank bits can be used in the Model H 30PV. Thanks to the single-step tool
retainer provided for the Model H 30PV, the SDS-plus shank bits can be installed just by adjusting the groove
position and pushing in.
4-1-3. Simple turning method, variable lock mechanism for easy working-angle adjustment of chisels, etc.
The tool swivel angle can be changed in 12 steps by turning the grip 60 degrees. The tool is securely locked at
the changed step by turning the grip back to the original position.
4-1-4. Soft-touch grip for easier handling
The double-layer molded handle consists of a plastic resin base covered with a soft plastic layer to ensure a soft
touch and firm, non-slip grip of the handles.
--- 3 ---
Housing Grass-fiber reinforced resin (green)
Grip, Handle
Crank case cover Glass-fiber reinforced resin (black)
Cylinder case cover
Variable speed control switch
D-shaped handle
6.9 A (110 V), 6.3 A (120 V), 3.4 A (220 V), 3.3 A (230 V), 3.2 A (240 V)
720 W
No-load: 0 to 4,200/min.
Full-load: 0 to 3,800/min.
Product: 4.2 kg (9.2 lbs.); excluding cord
Packed: 6.4 kg (14.1 lbs.)
Corrugated cardboard box with plastic tool case
Plastic tool case
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
1 pc.
Single-phase AC 50/60 Hz
110, 120, 220, 230, 240
AC single-phase series commutator motor
Double insulation
Power source
Voltage (V)
Motor type
Insulation structure
Enclosure
Type of switch
Type of handle
Full-load current
Power input
Striking speed
Weight
Packaging
Standard accessories
5. SPECIFICATIONS
H 30PV
Item
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
--- 4 ---
+
+
5-1. Optional Accessories
5-1-1. Demolition work
(1) Bull point (round type)
(SDS-plus shank)
5-1-2. Groove digging and edging work
(1) Cold chisel
(SDS-plus shank)
5-1-3. Grooving work
+
Code No.
316659
Overall length
250 mm (10")
Grooving chisel
(SDS-plus shank)
(2) Bull point (square type)
(SDS-plus shank)
Overall length
250 mm (10")
250 mm (10")
Code No.
303046
316656
No.
1
2
(2) Cutter
(SDS-plus shank)
Overall length
250 mm (10")
250 mm (10")
No.
1
2
Width
20 mm (3/4")
40 mm (1-9/16")
Code No.
316657
316658
--- 5 ---
(Note)
Code numbers listed above are subject to change. Please refer to periodic Technical News Bulletins.
5-1-4. Grease for impact drill
500 g (1.1 lbs.) Can
70 g (2.5 oz) Tube
Code No. 308471Code No. 980927
30 g (1 oz) Tube
Code No. 981840
6. COMPARISONS WITH SIMILAR PRODUCTS
6-1. Specification Comparisons
*: These values are listed on the catalog.
Maker
Model name
Power input
Power output
Full-load impact rate
Dimensions
5.2
8.6
2.2
8.0*
6.5*
W
W
/min
mm
mm
mm
HITACHI
H 30PV
720 (6.3 A)
940
550
---
505
---
kg
dB(A)
m/s
2
---
kg/min
(index)
Striking energy per stroke
Full-load vibration level
Insulation structure
No-load noise level
Weight (without cord)
3.9
Double insulation
Double insulation
Double insulation
DC
0 to 3,800 0 to 3,800 0 to 3,200
315
(12-13/32")
395
(15-9/16")
226
(8-7/8")
102
(4")
350
(13-25/32")
180
(7-1/8")
85
(3-11/32")
196
(7-23/32")
85
(3-11/32")
85 83 86
Length
Width
Height
Demolition performance
J
0.71
(57.3)
1.23
(100)
0.58
(47.0)
3.2
(7.1 lbs.)
4.2
(9.2 lbs.)
3.5
(7.7 lbs.)
--- 6 ---
6-2. Demolishing Performance Comparisons
The data shown in Fig. 1 are obtained in actual factory tests, and are for reference only. Demolished amount may
vary in accordance with operating conditions, operator skill, etc.
Fig. 1
7. PRECAUTIONS IN SALES PROMOTION
In the interest of promoting the safest and most efficient use of the Model H 30PV Hammer by all of our
customers, it is very important that at the time of sale the salesperson carefully ensures that the buyer seriously
recognizes the importance of the contents of the Handling Instructions, and fully understands the meaning of the
precautions listed on the Caution Plate attached to each tool.
7-1. Handling Instructions
Although every effort is made in each step of design, manufacture, and inspection to provide protection against
safety hazards, the dangers inherent in the use of any electric tool cannot be completely eliminated. Accordingly,
general precautions and suggestions for the use of electric power tools, and specific precautions and suggestions
for the use of the Hammer are listed in the Handling Instructions to enhance the safe, efficient use of the tool by
the customer. Salespersons must be thoroughly familiar with the contents of the Handling Instructions to be able
to offer appropriate guidance to the customer during sales promotion.
7-2. Caution Plate
The Model H 30PV unit is provided with a Nameplate (illustrated below) which lists basic safety precautions in its
use. Carefully ensure that the customer fully understands and follows these precautions before using the tool.
For Australia
H 30PV
D
C
17 (37 lbs.)
37 (82 lbs.)
21 (46 lbs.)
50
10
20
30
40
Demolished amount
(kg/30 min.)
Demolished weight
for 30 min. (kg)
At rated
voltage
--- 7 ---
7-3. Grease Replacement
The striking portion and the speed reduction portion of the Model H 30PV respectively use different types of
grease. Grease replacement is required if the unit is disassembled for maintenance or O-rings become damaged
or worn as described in 7-4.
The striking portion uses special grease. If the striking portion (inside the cylinder case and crank case) is
disassembled, thoroughly remove all of the old grease from each part. On reassembly, insert 40 g (1.4 oz) of new
grease into the crank case (connecting rod side). Do not exceed the designated amount of grease. Excessive
grease insertion may cause reduced striking performance.
The speed reduction portion (inside the gear cover) uses Hitachi Motor Grease No. 29 (Code No. 930035).
The proper supply volume is 50 g (1.8 oz). Never use the striking portion special grease in the speed reduction
portion. Special grease would leak into the motor portion and cause subsequent trouble.
7-4. O-Ring Replacement
The O-rings (mounted on the striker and piston) are extremely important to ensure adequate sealing of the air
pressure. Although the O-rings are made of special rubber to give them a long service life, they do nonetheless
become worn, and should be replaced by new ones periodically depending on frequency of use of the tool. With
average use, it is recommended that the O-rings be replaced at least every six months to ensure maximum
effectiveness.
For the U.S.A. and Canada
For Taiwan
--- 8 ---
8. REFERENCE INFORMATION
Structure:
Fig. 2
8-1. Striking Operation
The rotation of the armature is transferred to the crank shaft and connecting rod, which in turn cause the piston to
reciprocate inside the cylinder. As the piston reciprocates, the changing air pressure inside the air chamber
between the piston and the striker causes the striker to continuously strike against the end of the second hammer.
At the same time, the air-cushion effect within the air chamber absorbs the impact of the second hammer. Should
the air escape from the air chamber, the air-cushion effect would cease, and the impact energy would not be
absorbed. Accordingly, the O-rings mounted on the striker and piston play an extremely important role in sealing
the air within the air chamber.
Second hammer
Crank case cover
Cylinder
Air chamber
Connecting rod
Piston
O-rings
Striker
Armature
Crank shaft
8-2. Idling-proof Mechanism
When the bull point is released from the concrete surface, the second hammer moves to the position illustrated in
Fig. 3, and the sleeve moves out of striking position. When this occurs, the air holes are opened and the pressure
within the air chamber remains unchanged even though the piston continues to reciprocate, thereby preventing
striking operation.
--- 9 ---
Second hammer
Sleeve
Air
chamber
Air hole
Crank case
Housing
O-ring
Forward movement of
second hammer & striker
Front cap
Cylinder case
Fig. 4
Switch handle
O-ring
Oil
seal
8-3. Sealed and Dustproof Construction
The crank case and cylinder case are sealed by five O-rings, and an oil seal which serve to prevent leakage of the
grease, as well as to prevent dust and dirt from entering the mechanism.
Fig. 3
O-ring
O-ring
Retainer
sleeve
O-ring
Front cover
--- 10 ---
8-4. Tool Retainer
The Model H 30PV adopts the single-step tool retainer. Clean the shank portion of tool. (Fig. 5)
Adjust the groove position by turning the tool and push it in direction until it latches itself. (Fig. 6)
Check the latching by pulling on the tool. When removing the tool, pull Front Cap in direction (Fig. 7), and pull
out the tool (Fig. 8).
Fig. 8
Fig. 7
B
Front cap
Front cap
Tool shank
Fig. 5 Fig. 6
8-5. Adjusting Mechanism for Tool Swivel Angle
The tool can be turned every 30 degrees and can be fixed at the position of 12 steps. Grip (B) is turned 60
degrees in direction (Fig. 9), the tool swivel angle can be changed freely to any desired position. (Fig. 10)
It is locked completely by returning Grip (B) back to the original position.
Fig. 10
Fig. 9
(Note) Initially, grip (B) may not turn smoothly.
A
B
A
Grip (B)
--- 11 ---
9. REPAIR GUIDE
9-1. Precautions and Suggestions for Disassembly and Reassembly of Main Body
The numbers in [Bold] below correspond to the item numbers in the Parts List and exploded assembly diagrams.
9-1-1. Disassembly
Retainer disassembly
Remove the Front Cap [1] (since the Front Cap is made of rubber, grasp its outer face and strongly pull it to
remove). This allows Grip (A) [2] to be separated from the Retainer Sleeve [12]. (Fig. 11)
When the Retaining Ring D40 [3] is removed by means of the snap ring remover, Grip (B) [4], Ball Spring (A)
[5], Steel Ball D7.0 [9] (3 pcs.), Ball Holder [7], Ball Spring (B) [6] and Grip (C) [8] can be removed from the
Front Cover [10]. (Fig. 12)
Fig. 11
Front Cap
Fig. 12
Grip (A)
Grip (B) Ball Spring (A)
Ball Holder
Front Cover
Steel Ball
(3 pcs.)
Retaining Ring
Grip (C)Ball Spring (B)
--- 12 ---
Fig. 14
Retainer
Sleeve
Steel
Ball (2 pcs.)
Second
Hammer
Front
Cover
Piston and Striker O-rings
After removal of Grip (C) [8], secure the main body. Put the wrench (special repair tool J-123, Code No.
970885) on the width across flat portion of the Front Cover [10] and turn it counterclockwise to remove the
Front Cover [10] (Fig. 13).
Fig. 13
Front Cover
Wrench (J-123)
Spring (A)
Connecting Rod
Piston
Spring (A)
Damper (B)
Crank Shaft
Sleeve (A)
Hammer
Holder (B)
Cylinder
Holder
Striker
Cylinder
Washer
Damper (A)
Cylinder
Case
Crank Case Cover
Hammer
Holder (A)
The Retainer Sleeve [12], Steel Ball D7.0 [9], Spring (A) [13], Washer [14], Damper (A) [15], Hammer Holder
(A) [16] and Second Hammer [19] can be removed together with the Front Cover [10]. Remove Damper (B)
[20], Hammer Holder (B) [21] and Cylinder Holder [22] from the Cylinder Case [46], and tilt the orifice of the
Cylinder Case [46] downward. Then Sleeve (A) [50], Spring (B) [51] and Cylinder [52] come out of the
Cylinder Case [46]. If the Cylinder [52] does not come out, slightly tap the orifice of the Cylinder Case [46]
with a plastic hammer. Remove the Striker [48] from the Cylinder [52] (Fig. 14).
--- 13 ---
First gear disassembly
Remove the grease from the First Gear [42] side of the Crank Case Ass'y [35]. Then, use a bearing puller
(Special repair tool J-30, Code No. 970804), to remove the First Gear [42]. (Fig. 13)
Fig. 15
Remove the four Seal Lock Hex. Socket Hd. Bolts M4 x 10 [30] from the Crank Case Cover [31] and pull the
Crank Case Cover [31] upward to remove it. Remove the Connecting Rod [55] from the Crank Shaft [34].
Then the Piston [53] can be removed.
Retaining
Ring
Crank
Case
Hook
First Gear
Bearing Puller
Ball
Bearing
Crank
Shaft
--- 14 ---
Lubrication
Apply special grease (grease for electric impact drills) to the inner portion of the Connecting Rod [55],
the O-Rings [49] of the Striker [48] and the Piston [53], the inside diameter portion of Sleeve (A) [50] and
Hammer Holder (A) [16], the sliding portion of the Second Hammer [19], and Oil Seal (B) [39]. Seal 40 g of
special grease inside the Crank Case Ass'y [35] (Connecting Rod [55] side). Apply Hitachi Motor Grease
No. 29 to the Needle Bearing (HK0810) and the pinion portion of the Armature Ass'y [59]. Insert 50 g of the
Hitachi Motor Grease No. 29 into the Crank Case Ass'y [35] (First Gear [42] side).
Oil seals
Be very careful not to damage the O-Ring [33], O-Rings (I.D 19.2) [49], Oil Seal (B) [39], O-Ring (1AS-50)
[47], O-Ring (S-48) [11], O-Ring (S-15) [17] and O-Ring (S-38) [18].
9-1-3 Screw locking agent TB1401
Apply screw locking agent TB1401 to all hex. socket hd. bolts M4 and M5, and screw of Front Cover [10] (M48).
Note: If bolts are loosened by vibration, it could cause damage to the hammer. Ensure without fail that screw
locking agent is applied to threaded portions prior to assembly.
9-1-4. Tightening torque
(1) Hex. socket hd. bolts M4
(2) Hex. socket hd. bolts M5
(3) Tapping screws D4
(4) Tapping screws D5
(5) Housing mounting bolt (M5 x L35)
(6) Screws M5
(7) Screw of front cover (M48 pitch = 1.5)
9-1-2. Reassembly
Reassembly can be accomplished by following the disassembly procedures in reverse. However, special
attention should be given to the following items.
4.41
0.49
N•m (45 5 kgf•cm) (39.1
4.3
in-lbs.)
4.9
1.96
N•m (50 20 kgf•cm) (43.4
17.4
in-lbs.)
1.96
0.49
N•m (20 5 kgf•cm) (17.4
4.3
in-lbs.)
2.94
0.49
N•m (30 5 kgf•cm) (26.1
4.3
in-lbs.)
3.43
1.47
N•m (35
15
kgf•cm) (30.5
13.1
in-lbs.)
2.94
0.49
N•m (30 5 kgf•cm) (26.1
4.3
in-lbs.)
147
9.8
N•m (1500
100
kgf•cm) (1305 86 in-lbs.)
+
0
+
0
+
0
+
0
+
0
+
0
+
+
+
+
+ +
+
+
+
+
+
+
+
+
+
--- 15 ---
M2
Stator
Plug (A)
Noise
suppressor
Fig. 17
9-1-5. Wiring diagram
For products with noise suppressor
Fig. 16
Plug (B)
Stator
Switch
C2
C1
M1
1
2
M2
Stator
Plug (A)
Plug (B)
Stator
Switch
C2
C1
M1
1
2
For products without noise suppressor
--- 16 ---
Fig. 18
9-1-6. Wiring of variable speed control switch
Insert each cord into the terminal 1 and terminal 2 of the speed control switch as shown in Fig. 18 and tighten
the screw [tightening torque: 0.6 0.2 N•m (6 2 kg•cm, 5.2 1.7 in-lbs.)]. Insert each lead wire (black) coming
from Plug (B) into the terminals M1 and M2. Insert each lead wire (black) coming from the noise suppressor into
the terminals C1 and C2. After insertion, pull each lead wire slightly to check the lead wires do not come off. To
disconnect the lead wires, insert a small flatblade screwdriver into the slots near the terminals and pull out the
lead wires. (Fig. 16)
Noise suppressor (Black)
Noise suppressor (Black)
Plug (B) (Black)
Plug (B) (Black)
Cord (Black or brown)
Cord (White or blue)
9-1-7. Insulation Tests
On completion of reassembly after repair, measure the insulation resistance and conduct the dielectric strength
test.
Insulation resistance: 7 M Ω or more with DC 500 V Megohm Tester
Dielectric strength: AC 4,000 V/1 minute, with no abnormalities 220 V --- 240 V (and 110 V for U.K. products)
AC 2,500 V/1 minute, with no abnormalities 110 V --- 127 V (except for U.K. products)
9-1-8. No-load current values
After no-load operation for 30 minutes, the no-load current value should be as follows:
Voltage (V)
Current (A) max.
110
4.2
120
4.0
220
2.0
230
2.0
240
1.9
--- 17 ---
10. STANDARD REPAIR TIME (UNIT) SCHEDULES
MODEL 10 20 30 40
Fixed
Variable
H 30PV
Work Flow
Front Cover
O-Ring (S-48)
Retainer Sleeve
Spring (A)
Washer
Damper (A)
Hammer Holder
O-Ring (S-15)
O-Ring (S-38)
Second Hammer
Damper (B)
Hammer
Holder (B)
Cylinder Holder
O-Ring (S-25)
60 min.
50
Gear Cover
Needle Bearing
Armature Ass'y
Ball Bearing
(6001DD)
Ball Bearing
(608VV)
Washer (B)
Washer (A)
Tail Cover
Bearing
Bushing (B)
General Assembly
Front Cap
Grip (A)
Grip (B)
Ball Spring (A)
Ball Spring (B)
Ball Holder
Grip (C)
Cylinder Case
Sleeve (A)
Spring (B)
Cylinder
Housing Ass'y
Stator Ass'y
Handle
Plug (A)
Plug (B)
Crank Shaft
Feather Key
(4 x 4 x 12)
Ball Bearing
(6002DD)
Oil Seal (B)
First Gear
Crank Case
Ass'y
Striker
O-Ring x 2
Piston
Piston Pin
Connecting
Rod
Crank Case
Cover
O-Ring
Switch
Cord
ELECTRIC TOOL PARTS LIST
LIST NO.
HAMMER
Model H 30PV
2001 • 1 • 15
(E1)
E460
*
ALTERNATIVE PARTS
ITEM
NO.
CODE NO.
DESCRIPTION
REMARKS
NO.
USED
PARTS H 30PV
1 -- 01
1 319-554 FRONT CAP 1
2 319-555 GRIP (A) 1
3 318-582 RETAINING RING D40 1
4 319-556 GRIP (B) 1
5 319-560 BALL SPRING (A) 1
6 319-561 BALL SPRING (B) 1
7 319-562 BALL HOLDER 1
8 319-557 GRIP (C) 1
9 959-156 STEEL BALL D7.0 (10 PCS.) 5
10 319-559 FRONT COVER 1
11 980-715 O-RING (S-48) 1
12 319-558 RETAINER SLEEVE 1
13 319-563 SPRING (A) 1
14 319-565 WASHER 1
15 319-566 DAMPER (A) 1
16 319-564 HAMMER HOLDER (A) 1
17 319-567 O-RING (S-15) 1
18 980-717 O-RING (S-38) 1
19 319-568 SECOND HAMMER 1
20 319-569 DAMPER (B) 1
21 319-571 HAMMER HOLDER (B) 1
22 319-570 CYLINDER HOLDER 1
23 319-572 O-RING (S-25) 1
24 319-574 CYLINDER CASE COVER 1
25 HITACHI LABEL 1
26 319-928 SLEEVE (B) 1
27 931-008 FEATHER KEY 4X4X12 1
28 319-584 CRANK CASE CAP 1
29 319-572 O-RING (S-25) 1
30 878-356 SEAL LOCK HEX. SOCKET HD. BOLT M4X10 4
31 319-575 CRANK CASE COVER 1
* 32 NAME PLATE 1
33 314-030 O-RING 1
34 319-586 CRANK SHAFT 1
35 319-583 CRANK CASE ASS’Y 1 INCLUD.26,28,29,36-38
36 306-353 O-RING (S-22) 1
37 319-929 BUSHING 1
38 983-748 RETAINING RING FOR D24 HOLE 1
39 981-851 OIL SEAL (B) 1
40 600-2DD BALL BEARING 6002DDCMPS2L 1
41 948-001 RETAINING RING FOR D32 HOLE 1
42 319-588 FIRST GEAR 1
43 670-714 NEEDLE BEARING (HK0810) 1
44 319-591 GEAR COVER 1
45 992-253 HEX. SOCKET HD. BOLT (W/FLANGE) M5X25 4
46 319-573 CYLINDER CASE 1
47 990-067 O-RING (1AS-50) 1
48 319-576 STRIKER 1
49 319-577 O-RING (I.D 19.2) 2
50 319-578 SLEEVE (A) 1
51 319-579 SPRING (B) 1
*
ALTERNATIVE PARTS
ITEM
NO.
CODE NO.
DESCRIPTION REMARKS
NO.
USED
PARTS
H 30PV
1 -- 01
52 319-582 CYLINDER 1
53 319-580 PISTON 1
54 319-581 PISTON PIN 1
55 319-585 CONNECTING ROD 1
56 600-1DD BALL BEARING 6001DDCMPS2L 1
57 971-736 WASHER (B) 1
58 319-930 FAN 1
* 59 360-550U ARMATURE ASS’Y 110V-115V 1 INCLUD.56-58,72,73
* 59 360-550E ARMATURE ASS’Y 220V-230V 1 INCLUD.58
* 59 360-550F ARMATURE ASS’Y 240V 1 INCLUD.58
60 980-931 FAN GUIDE 1
61 992-509 HEX. HD. TAPPING SCREW D5X45 2
* 62 340-498C STATOR ASS’Y 110V 1 INCLUD.63
* 62 340-498G STATOR ASS’Y 115V 1 INCLUD.63
* 62 340-498E STA TOR ASS’Y 220V-230V 1 INCLUD.63
* 62 340-498F STATOR ASS’Y 240V 1 INCLUD.63
63 930-703 BRUSH TERMINAL 2
64 319-590 HOUSING ASS’Y 1 INCLUD.68,69
65 319-589 HEX. SOCKET HD. BOLT (W/FLANGE) M5X35 4
66 945-161 BRUSH CAP 2
* 67 999-073 CARBON BRUSH (AUTO STOP TYPE) (1 PAIR) 2
* 67 999-043 CARBON BRUSH (1 PAIR) 2 FOR TPE
68 958-900 BRUSH HOLDER 2
69 938-477 HEX. SOCKET SET SCREW M5X8 2
70 319-587 TAIL COVER 1
71 307-811 TAPPING SCREW (W/FLANGE) D4X16 (BLACK) 2
72 982-631 WASHER (A) 1
73 608-VVM BALL BEARING 608VVC2PS2L 1
74 310-111 BEARING BUSHING (B) 1
75 959-140 CONNECTOR 50091 (10 PCS.) 1
76 981-500 INTERNAL WIRE 1
77 307-294 MACHINE SCREW (W/WASHERS) M5X16 (BLACK) 4
78 319-597 HANDLE 1
79 319-594 TRIGGER 1
* 80 319-592 SWITCH (B) (2P PILLAR TYPE) W/O LOCK 1
* 80 319-593 SWITCH (A) (2P PILLAR TYPE) W/O LOCK 1 FOR TPE,GBR (110V),USA,CAN
* 81 994-273 NOISE SUPPRESSOR 1 EXCEPT FOR USA,CAN
* 82 317-492 SUPPORT (B) 1 EXCEPT FOR USA,CAN
83 319-598 HANDLE COVER 1
84 301-653 TAPPING SCREW (W/FLANGE) D4X20 (BLACK) 2
* 85 981-373 TUBE (D) 2 FOR CORD
86 937-631 CORD CLIP 1
87 984-750 TAPPING SCREW (W/FLANGE) D4X16 2
88 305-558 TAPPING SCREW (W/FLANGE) D5X25 (BLACK) 2
* 89 953-327 CORD ARMOR D8.8 1
* 89 938-051 CORD ARMOR D10.1 1
* 90 500-424Z CORD 1 (CORD ARMOR D8.8) FOR SIN
* 90 500-439Z CORD 1 (CORD ARMOR D8.8) FOR AUS
* 90 500-446Z CORD 1 (CORD ARMOR D10.1) FOR HKG,GBR (230V)
* 90 500-465Z CORD 1 (CORD ARMOR D8.8) FOR GBR (110V)
* 90 500-390Z CORD 1 (CORD ARMOR D8.8)
--- 21 ---
*
ALTERNATIVE PARTS
ITEM
NO.
CODE NO.
DESCRIPTION REMARKS
NO.
USED
PARTS
STANDARD ACCESSORIES
ITEM
NO.
CODE NO.
DESCRIPTION REMARKS
NO.
USED
OPTIONAL ACCESSORIES
ITEM
NO.
CODE NO.
DESCRIPTION REMARKS
NO.
USED
* 90 500-391Z CORD 1 (CORD ARMOR D10.1) FOR SUI
* 90 500-214Z CORD 1 (CORD ARMOR D10.1) FOR TPE
* 90 500-249Z CORD 1 (CORD ARMOR D8.8) FOR USA,CAN
91 313-092 PLUG (A) 1
* 92 319-595 PLUG (B) 1
* 92 319-596 PLUG (B) 1 FOR USA,CAN
501 319-599 CASE 1
601 981-840 GREASE (A) FOR HAMMER.HAMMER DRILL (30G) 1
602 308-471 GREASE FOR HAMMER.HAMMER DRILL (70G) 1
* 603 980-927 GREASE FOR HAMMER.HAMMER DRILL (500G) 1 EXCEPT FOR USA,CAN
604 303-046 BULL POINT (SDS+) 250MM(ROUND SHANK TYPE) 1
605 302-976 ANCHOR SETTING ADAPTER A (SDS+)W1/4X260L 1
606 302-975 ANCHOR SETTING ADAPTER A(SDS+)W5/16X260L 1
607 303-621 ANCHOR SETTING ADAPTER A (SDS+)W3/8X160L 1
608 302-974 ANCHOR SETTING ADAPTER A (SDS+)W3/8X260L 1
609 302-979 ANCHOR SETTING ADAPTER B (SDS+)W1/4X260L 1
610 302-978 ANCHOR SETTING ADAPTER B(SDS+)W5/16X260L 1
611 303-622 ANCHOR SETTING ADAPTER B (SDS+)W3/8X160L 1
612 302-977 ANCHOR SETTING ADAPTER B (SDS+)W3/8X260L 1
Printed in Japan
(010115N)
1 -- 01
H 30PV
Loading...