Hitachi G10SR2, G12SR2, G13SR2, G 12SA2, G 13SB2 Handling Instructions Manual

G12SR2
Disc Grinder Model G10SR2•G12SR2•G13SR2
Handling instructions
NOTE:
Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an important reference when using this power tool.
1
GENERAL OPERATIONAL PRECAUTIONS
WARNING! When using electric tools, basic safety
precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following. Read all these instructions before operating this product and save these instructions. For safe operations:
1. Keep work area clean. Cluttered areas and benches invite injuries.
2. Consider work area environment. Do not expose power tools to rain. Do not use power tools in damp or wet locations. Keep work area well lit. Do not use power tools where there is risk to cause fire or explosion.
3. Guard against electric shock. Avoid body contact with earthed or grounded surfaces. (e.g. pipes, radiators, ranges, refrigerators).
4. Keep children and infirm persons away. Do not let visitors touch the tool or extension cord. All visitors should be kept away from work area.
5. Store idle tools. When not in use, tools should be stored in a dry, high or locked up place, out of reach of children and infirm persons.
6. Do not force the tool. It will do the job better and safer at the rate for which it was intended.
7. Use the right tool. Do not force small tools or attachments to do the job of a heavy duty tool. Do not use tools for purposes not intended; for example, do not use circular saw to cut tree limbs or logs.
8. Dress properly. Do not wear loose clothing or jewelry, they can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protecting hair covering to contain long hair.
9. Use eye protection. Also use face or dust mask if the cutting operation is dusty.
10. Connect dust extraction equipment. If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used.
11. Do not abuse the cord. Never carry the tool by the cord or yank it to disconnect it from the receptacle. Keep the cord away from heat, oil and sharp edges.
12. Secure work. Use clamps or a vise to hold the work. It is safer than using your hand and it frees both hands to operate tool.
13. Do not overreach. Keep proper footing and balance at all times.
14. Maintain tools with care. Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubrication and changing accessories. Inspect tool cords periodically and if damaged, have it repaired by authorized service center. Inspect extension cords periodically and replace, if damaged. Keep handles dry, clean, and free from oil and grease.
15. Disconnect tools. When not in use, before servicing, and when changing accessories such as blades, bits and cutters.
16. Remove adjusting keys and wrenches. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.
17. Avoid unintentional starting. Do not carry a plugged-in tool with a finger on the switch. Ensure switch is off when plugging in.
18. Use outdoor extension leads. When tool is used outdoors, use only extension cords intended for outdoor use.
19. Stay alert. Watch what you are doing. Use common sense. Do not operate tool when you are tired.
20. Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in this handling instructions. Have defective switches replaced by an authorized service center. Do not use the tool if the switch does not turn it on and off.
21. Warning The use of any accessory or attachment, other than those recommended in this handling instructions, may present a risk of personal injury.
22. Have your tool repaired by a qualified person. This electric tool is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts. Otherwise this may result in considerable danger to the user.
PRECAUTIONS ON USING DISC GRINDER
1. Never operate these power tools without Wheel
Guards.
2. Check that speed marked on the wheel is equal to
or greater than the rated speed of the grinder. Use only depressed center wheels rated at 80m/s (72m/s only for 100 mm disc grinders) or more.
3. Ensure that the wheel dimensions are compatible
with the grinder and that the wheel fits the spindle.
4. Abrasive wheels shall be stored and handled with
care in accordance with manufacturer’s instructions.
5. Inspect the depressed center wheel before use, do
not use chipped, cracked or otherwise defective products.
6. Always hold the body handle and side handle of
the power tool firmly. Otherwise the counterforce produced may result in inaccurate and even dangerous operation.
7. Do not use cutting-off wheels for side grinding.
8. Do not use of separate reducing bushings or adapters
to adapt large hole abrasive wheels.
9. The wheel continues to rotate after the tool is
switched off.
2
SPECIFICATIONS
*Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Wrench ........................................................................1
(2) Side handle ................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
Removal of casting fin and finishing of various types of steel, bronze and aluminum materials and castings.
Grinding of welded sections or sections cut by
means of a cutting torch.
Grinding of synthetic resins, slate, brick, marble, etc.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If the plug is connected to a receptacle while the power switch is in the ON position, the power tool will start operating immediately, which could cause a serious accident.
3. Extension cord
When the work area is removed from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.
4. Fitting and adjusting the wheel guard
The wheel guard is a protective device to prevent injury should the depressed center wheel shatter during operation. Ensure that the guard is properly fitted and fastened before commencing grinding operation. By slightly loosening the setting screw, the wheel guard can be turned and set at any desired angle for maximum operational effectiveness. Ensure that the setting screw is thoroughly tightened after adjusting the wheel guard.
5. Ensure that mounted wheels and points are fitted in accordance with the manufacturers instructions. Ensure that the depressed center wheel to be utilized is the correct type and free of cracks or surface
defects. Also ensure that the depressed center wheel is properly mounted and the wheel nut is securely tightened, Refer to the section on Depressed Center Wheel Assembly Ensure that blotters are used when they are provided with the bonded abrasive product and when they are required. Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels. For tools intended to be fitted with threaded hole wheel, ensure that the thread in the wheel is long enough to accept the spindle length. Do not use cutting off wheel for side grinding.
6. Conducting a trial run
Ensure that the abrasive products is correctly mounted and tightened before use and run the tool at no-load for 30 seconds in a safe position, stop immediately if there is considerable vibration or if other defects are detected. If this condition occurs, check the machine to determine the cause.
7. Confirm the push button.
Confirm that the push button is disengaged by pushing push button two or three times before switching the power tool on (See Fig. 2).
8. Fixing the side handle
Screw the side handle into the gear cover.
PRACTICAL GRINDER APPLICATION
1. Pressure
To prolong the life of the machine and ensure a first class finish, it is important that the machine should not be overloaded by applying too much pressure. In most applications, the weight of the machine alone is sufficient for effective grinding. Too much pressure will result in reduced rotational speed, inferior surface finish, and overloading which could reduce the life of the machine.
2. Grinding angle
Do not apply the entire surface of the depressed center wheel to the material to be ground. As shown in Fig. 1, the machine should be held at an angle of 15° – 30° so that the external edge of the depressed center wheel contacts the material at an optimum angle.
Model G10SR2 G12SR2 G13SR2 Voltage (by areas)* (110V, 120V, 220V, 230V, 240V) Power Input* 650 W No-load speed 11000 min
-1
10000 min
-1
Outer dia. × hole dia. 100 × 16 mm 115 × 22 mm 125 × 22 mm
Wheel
Peripheral speed 72 m/s 80 m/s
Weight (Only main body) 1.4 kg
3
Fig. 1
3. To prevent a new depressed center wheel from digging into the workpiece, initial grinding should be performed by drawing the grinder across the workpiece toward the operator (Fig. 1 direction B). Once the leading edge of the depressed center wheel is properly abraded, grinding may be conducted in either direction.
4. Precautions immediately after finishing operation
The wheel continues to rotate after the tool is switched off. After switching off the machine, do not put it down until the depressed center wheel has come to a complete stop. Apart from avoiding serious accidents, this precaution will reduce the amount of dust and swarf sucked into the machine.
CAUTIONS
Check that the work piece is properly supported.Ensure that ventilation openings are kept clear when
working in dusty conditions. If it should become necessary to clear dust, first disconnect the tool from the mains supply (use non­metallic objects) and avoid damaging internal parts.
Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite flammable substances.
Always use protective safety glasses and hearing
protectors, use other personal protective equipment such as gloves, apron and helmet when necessary.
Always use eye and ear protection.
Other personal protective equipment such as dust mask, gloves, helmet and apron should be worn when necessary. If in doubt, wear the protective equipment.
When the machine is not use, the power source
should be disconnected.
ASSEMBLING AND DISASSEMBLING THE DEPRESSED CENTER WHEEL (Fig. 2)
CAUTION Be sure to switch OFF and disconnect the
attachment plug from the receptacle to avoid a serious accident.
1. Assembling (Fig. 2)
(1) Turn the disc grinder upsidedown so that the spindle
is facing upward.
(2) Align the across flats of the wheel washer with the
notched part of the spindle, then attach them.
(3) Fit the protuberance of the depressed center wheel
onto the wheel washer.
(4) Screw the wheel nut onto the spindle.
(5) While pushing the push button with one hand, lock
the spindle by turning the depressed center wheel slowly with the other hand. Tighten the wheel nut by using the supplied wrench as shown in Fig. 2.
2. Disassembling
Follow the above procedures in reverse.
CAUTIONS
Comfirm that the depressed center wheel is mounted
firmly.
Confirm that the push button is disengaged by
pushing push button two or three times before switching the power tool on.
Fig. 2
MAINTENANCE AND INSPECTION
1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of cracks and surface defects.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard.
3. Inspecting the carbon brushes
For your continued safety and electrical shock protection, carbon brush inspection and replacement on this tool should ONLY be performed by a Hitachi Authorized Service Center.
4. Replacing supply cord
If the supply cord of tool is damaged, the tool must be returned to Hitachi Authorized Service Center for the cord to be replaced.
5. Maintenance of the motor
The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding
15° – 30°
AB
Wrench
Wheel nut
Depressed center wheel
Wheel washer
Wheel guard
Spindle
Push button
4
does not become damaged and/or wet with oil or water.
6. Service parts list CAUTION
Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts may be changed without prior notice.
NOTE
Due to HITACHIs continuing program of research and development, the specifications herein are subject to change without prior notice.
5
Item
Part Name
Qty
No.
1 TAPPING SCREW D5 × 25 1
2 GUARD PLATE 1
3 PUSHING BUTTON 1
4 GEAR COVER ASS
Y
1
5 SPECIAL NUT M7 1
6 PINION 1
7
SLOTTED HD. SCREW
(SEAL LOCK) M4 × 10
2
8
BALL BEARING
608VVC2PS2L
1
9 INNER COVER 1
10 ARMATURE 1
11 FAN GUIDE 1
12
HEX. HD. TAPPING
SCREW D4 × 70
2
13 STATOR 1
14 DUST SEAL 2
15
BALL BEARING
626VVC2PS2L
1
16 RUBBER BUSHING 1
17 LOCK PIN 1
18
RETAINING RING
FOR D11 SHAFT
1
19 WAVE WASHER 1
20 GEAR 1
21
SEAL LOCK SCREW
(W/SP. WASHER) M4 × 10
3
22 BEARING COVER (B) 1
23
BALL BEARING
6001VVCMPS2L
1
24 FELT PACKING 1
25 PACKING GLAND 1
26
SEAL LOCK SCREW
(W/SP. WASHER) M4 × 12
4
27 WOODRUFF KEY 1
28 SPINDLE 1
29
MACHINE SCREW
(W/SP. WASHER) M5 × 16
2
30 SET PLATE 1
31 WHEEL GUARD ASS
Y
1
32 WHEEL WASHER 1
33 D. C. WHEELS 1
Item
Part Name
Qty
No.
34 WHEEL NUT M14 1
35 GEAR AND PINION SET 1
36 SLIDE KNOB 1
37 HOUSING ASS
Y
1
38 NAME PLATE 1
39 EARTH TERMINAL 1
40 TERMINAL 1
41 NOISE SUPPRESSOR 1
42 SWITCH HOLDER 1
43 PILLAR TERMINAL 1
44 SPRING 1
45 SLIDE BAR 1
45 SLIDE BAR 1
46 HITACHI LABEL 1
47 BRUSH CAP 2
48 CARBON BRUSH 2
49 BRUSH HOLDER 2
50 SWITCH 1
51
MACHiNE SCREW
(W/WASHER) D3.5 × 6
2
52 TERMINAL 1
53 CORD CLIP 1
54
TAPPING SCREW
(W/FLANGE) D4 × 16
1
55 CORD ARMOR 1
56 TAIL COVER 1
57
TAPPING SCREW
(W/FLANGE) D4 × 45
4
58 CORD 1
501 WRENCH 1
502 SIDE HANDLE 1
501
502
1
2
3
4
6
7
5
8
9
10
171819
202122
23
24
25
26
27
28
29
30
31
32
33
34
35
36
38
37
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
11
12
14
15
16
13
6
212 Code No. C99119111 Printed in China
Loading...