Hitachi DTTA-371010, DTTA-371290, DTTA-371440 Quick installation guide

IBM storage products

Quick installation guide

Deskstar 14GXP

AT/IDE

Models: DTTA-371010

DTTA-371290
DTTA-371440

Handling precautions

1. Do not cover the breather hole! Covering the
breather hole may result in loss of data.

2. Do not press on the drive! Do not apply any force
to the drive during handling or installation.

3. Always handle the drive with care to prevent
damage from shock, vibration, or electrostatic
discharge (ESD).

4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.

5. Turn off and unplug your computer. Remove the
cover.

6. When installing the drive, touch a grounded,
unpainted metal surface with the static-protective
package containing the drive for at least two seconds.
(This drains static electricity from the package and
from your body.)

7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.

8. Save the drive packaging material including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it in
the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.

Quick installation procedure

Note: It is advisable to backup all data before
proceeding with the installation.

If your system BIOS cannot handle large capacity
drives (due to inadequate address locations, most
systems are limited to accessing drives with a
capacity of 8.4GB or less), you may need to use a
disk overlay program such as Ontrack’s Disk
Manager. The following procedure uses the Ontrack
Disk Manager software. Information on obtaining a
copy of Ontrack’s Disk Manager can be found on the
Web at www.ibm.com/harddrive.

Setting the jumpers

1. Refer to your computer manual to determine if you
require the 15- or 16-head logical architecture.

2. In a one drive system, configure your new drive as
Master (Device 0).

3. In a two drive system, one drive must be desig­nated as the Master, the other as the Slave (Device 1)

4. When installing the new drive as a Slave, check the
Master drive to determine if a jumper change is
required to indicate that a Slave drive is present.

5. Consult your manual to see if your computer
supports Cable Select before choosing this option.

16 head logical architecture

Jumper pins
Master A-B & G-H
Slave A-B & C-D
Cable Select A-B & E-F
Slave Present E-F & G-H

39 19 1 I G E C A

15 head logical architecture

Jumper pins
Master A-C & G-H
Slave A-C
Cable Select A-C & E-F
Slave Present A-C, E-F

& G-H

40 20 2 H F D B

IBM Hard Disk Drive Technical Support Center version 3.1

Page 1

IBM storage products

Attaching the drive

1. Turn off the computer, unplug the power cord, and
open the case.

2. Match pin 1 of the 40-pin cable to pin 1 of the drive
interface connector. Pin 1 is usually denoted by a
stripe along the edge of the cable.

3. Insert a power plug in either the 3- or 4-pin power
connector.

Mounting the Drive

1. Mount the drive securely, using the appropriate
brackets or rails, in any axes, using four 6-32 UNC
metric screws in either bottom or side mounting
holes.

2. The maximum screw insertion depth for the bottom
mounting is 4 mm and for side mounting 4.5 mm.

Configuring your computer

1. If your computer has a plug-in IDE card with a drive

installation procedure, follow the manufacturer’s in­structions.

2. Plug in the power cord and power on your com-

puter. Your computer may detect a configuration
change and prompt you to proceed to the Setup
screen. If so, proceed to step 4.

3. If your computer does not prompt you to reconfig-

ure, enter your computer’s Setup, typically by key
selection or keyboard combinations during power-on
or during a reboot. Refer to your computer’s docu­mentation for the proper key sequence. If the com­puter fails to boot up, power off, remove the new hard
drive and reconfigure your system to its original con­figuration. Reboot and enter your computer’s Setup.
Follow the directions in step 4, then reattach the new
hard drive.

4. Select “Auto Detect” if your computer Setup sup-

ports this feature. If your computer does not Auto
Detect the drive, select the appropriate UDT (User
Definable Type) for the model being installed.
Then run Disk Manager.

number

HeadsCylindersIBM model

Sector
/Track

Capacity

14.4GB631516,383DTTA-371440

12.9GB631516,383DTTA-371290

10.1GB631516,383DTTA-371010

9.1GB631516,383clip version

remove the new drive to return to your original
configuration and contact technical support.

®

© International Business Machines Corporation 2002

www.ibm.com/harddrive

IBM Hard Disk Drive Technical Support Center

Dept. D8M
3605 Highway 52 North
Rochester, MN 55901
Telephone: 888.IBM.5214 or 507.253.4110
Fax: [phone]
E-mail: [e-mail]

Singapore Technical Support Center

Telephone: [phone]
E-mail: [e-mail]

IBM Systems Storage Division

5600 Cottle Road
San Jose, CA 95193
www.ibm.com/storage

Asia-Pacific Headquarters: 65.320.1234
European Headquarters: 44.01.705.561.871
Japan Sales Branch Office: 81.46645.1039

Printed in the United States of America
01-99
All Rights Reserved
IBM is the registered trademark of International Business Machines Corporation.

Other company, product, and service names may be trademarks or service marks of others.
Produced by the IBM Hard Disk Drive Technical Support Center.
OEM Hard Disk Drive Specifications for DTTA-3xxxxx, revision 2.0
Product Description data represents IBM’s design objectives and is provided for

comparative purposes; actual results may vary based on a variety of factors. This product
data does not constitute a warranty. Questions regarding IBM’s warranty terms or
methodology used to derive this data should be referred to the IBM Hard Disk Drive
Technical Support Center. Data subject to change without notice.

Date:26 November 2002

Running Disk Manager

1. Insert the Ontrack diskette and reboot your

computer.

2. Type DM and press [ENTER] to run Disk Manager.

3. Under “Select an Installation Option”, select (E)asy

Disk Installation.

4. Select a drive for installation; Disk Manager will

partition and format the drive.

5. A status dialog will indicate a successful instal-

lation.
If, after complete installation, your system will not

boot up, recheck all settings. If it still will not boot up,

IBM Hard Disk Drive Technical Support Center version 3.0

Page 2