Hitachi DH30PC, DH30PB User Manual

MODEL ROTARY HAMMER MODÈLE MARTEAU ROTATIF MODELO MARTILLO GIRATORIO

DH 30PB • DH 30PC

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious

bodily injury! This manual contains important information about product safety. Please read and understand this manual BEFORE operating the power tool. Please keep this manual available for other users and owners before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort ou de sérieuses blessures corporelles! Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar en lesiones de gravedad o la muerte! Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.

DOUBLE INSULATION DOUBLE ISOLATION AISLAMIENTO DOBLE

English

IMPORTANT INFORMATION ............. 3

MEANINGS OF SIGNAL WORDS ...... 3

SAFETY ................................................... 4

GENERAL SAFETY RULES ................. 4

SPECIFIC SAFETY RULES AND SYMBOLS DOUBLE INSULATION FOR SAFER

OPERATION ................................... 8

FUNCTIONAL DESCRIPTION ................ 9

MANE OF PARTS ................................ 9

SPECIFICATIONS ................................ 9

Français

INFORMATIONS IMPORTANTES .... 26

SIGNIFICATION DES MOTS

D’AVERTISSEMENT .................... 26

SECURITE ............................................. 27

REGLES GENERALES DE SECURITE REGLES DE SECURITE SPECIFIQUES ET SYMBOLES DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR

DESCRIPTION FONCTIONNELLE ........ 33

NOM DES PARTIES .......................... 33

SPECIFICATIONS .............................. 33

TABLE DES MATIERES

CONTENTS

Page

ASSEMBLY AND OPERATION ............ 10

..... 6

MAINTENANCE AND INSPECTION .... 18

ACCESSORIES ...................................... 20

Page

ASSEMBLAGE ET FONCTIONNEMENT

..... 27

.. 29

ENTRETIEN ET INSPECTION ............... 43

...... 32

ACCESOIRES ........................................ 45

Page

APPLICATIONS ................................. 10

PRIOR TO OPERATION..................... 10

HOW TO USE .................................... 12

HOW TO USE THE CORE BIT (FORLIGHT LOAD) ....

STANDARD ACCESSORIES ........... 20

OPTIONAL ACCESSORIES............. 20

APPLICATIONS ................................. 34

AVANT L’UTILISATION .................... 34

UTILISATION..................................... 37

COMMENT UTILISER LA COURONNE

(POUR UNE CHARGE LEGERE)

ACCESSOIRES STANDARD ............. 45

ACCESSOIRES SUR OPTION ........... 45

............ 41

Page

.... 34

Español

INFORMACIÓN IMPORTANTE ............ 51

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN .............................. 51

SEGURIDAD ......................................... 52

NORMAS GENERALES DE SEGURIDAD NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD AISLAMIENTO DOBLE PARA OFRECER UNA

OPERACIÓN MÁS SEGURA

DESCRIPCIÓN FUNCIONAL ................ 58

NOMENCLATURA ......................... 58

ESPECIFICACIONES ...................... 58

................ 57

ÍNDICE

Página

...... 52

.... 54

MONTAJE Y OPERACIÓN ................... 59

APLICACIONES .............................. 59

ANTES DE LA OPERACIÓN ........... 59

COMO SE USA............................... 61

MANTENIMIENTO E INSPECCIÓN ..... 68

ACCESORIOS ....................................... 70

Página

MODO DE USAR LA BARRENA TUBULAR

(PARACARGAS LIGERAS)

ACCESORIOS ESTÁNDAR.......... 70

ACCESORIOS OPCIONALES ...... 70

................... 65

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result

in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

English

SAFETY

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust of fumes.

(3) Keep bystanders children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety (1) Double Insulated tools are equipped with a polarized plug (one blade is

wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double Insulation

wire grounded power cord and grounded power supply system.

(2) Avoid body contact with grounded surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is

grounded.

(3) Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

(4) Do not abuse the cord. Never use the cord to carry the tools or pull the

plug from a receptacle. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

(5) When operating a power tool outside, use an outdoor extension cord

marked “W-A” or “W”. These cords are rated for outdoor use and reduce

the risk of electric shock.

3. Personal Safety (1) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating

power tools may result in serious personal injury.

eliminates the need for the three

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying

tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench

or a key that is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear protective glasses. Dust mask, non-

skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

4. Tool Use and Care (1) Use clamps or other practical way to secure and support the workpiece to

a stable platform. Holding the work by hand or against your body is unstable

and may lead to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool

will do the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be

controlled with the switch is dangerous and must be repaired.

(4) Disconnect the plug form the power source before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures

reduce the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hands of untrained users.

(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

(7) Check for misalignment or binding of moving parts, breakage of parts, and

any other condition that may affect the tool's operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly

maintained tools.

(8) Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool, may become hazardous

when used with another tool.

5. Service (1) Tool service must be performed only by a qualified repair personnel. Service

or maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow

instructions in the Maintenance section of this manual. Use of unauthorized

parts or failure to follow Maintenance Instruction may create a risk of electric shock or injury.

English

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a

“live” wire will make exposed metal parts of the tool “live” and shock the operator.

2. ALWAYS wear ear protectors when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

3. NEVER touch the tool bit with bare hands after operation.

4. NEVER wear gloves made of stuff liable to roll up such as cotton, wool, cloth or

string, etc.

5. ALWAYS attach the side handle and securely grip the Rotary Hammer.

6. NEVER touch moving parts. NEVER place your hands, fingers or other body parts near the tool’s moving

parts.

7. NEVER operate without all guards in place. NEVER operate this tool without all guards or safety features in place and in

proper working order. If maintenance or servicing requires the removal of a guard or safety feature, be sure to replace the guard or safety feature before resuming operation of the tool.

8. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool. Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting tree limbs or logs.

9. NEVER use a power tool for applications other than those specified. NEVER use a power tool for applications other than those specified in the

Instruction Manual.

10. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw the tool. NEVER allow the tool to be operated by children, individuals unfamiliar with its operation or unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

12. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not be used until repaired.

English

13.Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and accessories which have been mounted to the tool should be secure and tight.

14. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check for dust build-up frequently.

15. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its nameplate. If using the power tool at a higher voltage than the rated voltage, it will result in abnormally fast motor revolution and may damage the unit and the motor may burn out.

16. NEVER use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise appears defective, stop using it immediately and arrange for repairs by a Hitachi authorized service center.

17. NEVER leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

18. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may be deformed, cracked, or damaged.

19. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may damage and crack plastic parts. Do not wipe them with such solvents. Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry thoroughly.

20. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI Standard Z87.1.

21. ALWAYS be careful with buried object such as an underground wiring.

Touching these active wiring or electric cable with this tool, you may receive an electric shock. Confirm if there are any buried object such as electric cable within the wall, floor or ceiling where you are going to operate here after.

22. Definitions for symbols used on this tool

V ............volts

Hz .......... hertz

A ............ amperes

o ........... no load speed

English

W ........... watt

........... Class II Construction

---/min ... revolutions per minute

.......... Alternating current

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation “ means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “ nameplate. Although this system has no external grounding, you must still follow the normal electrical safety precautions given in this Instruction Manual, including not using the power tool in wet environments. To keep the double insulation system effective, follow these precautions: 䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble

this power tool, and only genuine HITACHI replacement parts should be installed.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy

water, and dry thoroughly. Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve.

” or the words “Double insulation” appear on the power tool or on the

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool.

NAME OF PARTS

English

Drill Bit

Stopper

Grip

Side Handle

Housing

(Under the Tail Cover)

Change Lever

Set Screw

Fig. 1

Tail Cover

Nameplate

Brush Cap (Inside the Tail Cover)

Trigger

Handle

SPECIFICATIONS

Model DH30PB DH30PC Motor Single-Phase, Series Commutator Motor Power Source Single-Phase, 120V 60Hz Current 7.4A Capacity Concrete: 5/32" – 1-3/16" (4mm – 30mm)

Steel: 1/2"(13mm)

Wood: 1-1/4" (32mm) No-Load Speed 0 – 850/min. Full-load Impact Rate 0 – 3700/min. Weight 10.4 lbs (4.7 kg) 10.6 lbs (4.8 kg)

English

ASSEMBLY AND OPERATION

APPLICATIONS

Rotation and striking function

䡬 Drilling anchor holes 䡬 Drilling holes in concrete 䡬 Drilling holes in tile

Rotation only function

䡬 Drilling in steel or wood (with optional accessories). 䡬 Tightening machine screws, wood screws (with optional accessories).

Striking only function

䡬 Light-duty chiselling of concrete, groove digging and edging.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while the switch is in the ON position, the power tool will start operating immediately and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING:

Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact a licensed electrician to make appropriate repairs. If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard.

English

5. Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to prescribed precautions.

6. Mounting the drill bit (Fig. 2)

(1) To attach a drill bit (SDS-plus shank),

Part of SDS-plus shank

Front cap

fully pull the grip in the direction of the arrow as shown in Fig. 2 and insert the drill bit as far as it will go while manually turning.

Drill bit

Grip

(2) By releasing the grip, the drill bit will

be secured.

(3) To remove the drill bit, fully pull the

Fig. 2

grip in the direction of the arrow and pull out the drill bit.

7. Installation of dust cup or dust

Dust Cup

collector (B) (Optional accessories) (Fig. 3, Fig. 4)

When using a rotary hammer for upward drilling operations attach a dust cup or dust collector (B) to collect dust or particles for easy operation.

䡬 Installing the dust cup

Use the dust cup by attaching to the drill bit a shown in Fig. 3.

Dust Collector (B)

When using a bit which has big diameter, enlarge the center hole of the dust cup with this rotary hammer.

䡬 Installing dust collector (B)

When using dust collector (B), insert dust collector (B) from the tip of the bit by aligning it to the groove on the grip (Fig. 4)

CAUTION:

䡬 The dust cup and dust collector (B) are for exclusive use of concrete drilling

work. Do not use them for wood or metal drilling work.

䡬 Insert dust collector (B) completely into the chuck part of the main unit. 䡬 When turning the rotary hammer on while dust collector (B) is detached from

a concrete surface, dust collector (B) will rotate together with the drill bit. Make sure to turn on the switch after pressing dust cup on the concrete surface.

Fig. 3

Fig. 4

English

(When using dust collector (B) attached to a drill bit that has more than 7-15/ 32" (190 mm) of overall length, dust collector (B) cannot touch the concrete surface but rotates. Therefore please use dust collector (B) by attaching to drill bits which have 6-17/32" (166 mm), 6-19/64" (160 mm) and 4-21/64" (110 mm) overall length.

䡬 Dump particles after every two or three holes when drilling. 䡬 Please replace the drill bit after removing dust collector (B).

8. Selecting the driver bit

Screw heads or bits will be damaged should an inappropriate bit for the screw diameter be employed to drive in the screws.

9. Selecting the function mode

You can switch functions to the 3 modes of “strike only, “rotation + strike”, and “rotation only” by turning the change lever while pressing the push button. Set the

CAUTION:

䡬 Before operating the change lever, check and make sure that the motor has

stopped. A failure can occur if it is operated while the motor is running.

䡬 If the change lever does not move up to the mark position of each mode, carry

out switching while turning the grip end to left and right. Also, it can become difficult to change the mode at low temperature, and therefore perform warming-up.

䡬 To operate the change lever, press the push button, and release the lock of the

change lever. Also, check and make sure after operation that the push button has returned and that the change lever has been locked.

䡬 Switch the change lever without mistake. If it is used at a position halfway,

there is a fear that the service life of the switching mechanism may be shortened.

䡬 Note that it is impossible to switch from “rotation only” to “strike only” or

from “strike only” to “rotation only”. Switch over via “rotation + strike”. (DH30PC)

mark position of the change lever to that of the mode to be used.

HOW TO USE

CAUTION:

䡬 To prevent accidents, make sure to turn the switch off and disconnect the plug

from the receptacle when the drill pits and other various parts are installed or removed. The power switch should also be turned off during a work break and after work.

1. Switch operation

The rotation speed of the drill bit can be controlled steplessly by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the switch is pulled more.

2. Rotation + Striking

This rotary hammer can be set to rotation and striking mode by pressing the push button and turning the

change lever to (1) Mount the drill bit. (2) Pull the trigger switch after applying

the drill bit tip to the drilling position

(Fig. 6) (3) Pushing the rotary hammer forcibly is

not necessary at all. Pushing slightly

so that drill dust comes out gradually

is just sufficient.

CAUTION:

䡬 When the drill bit touches an iron

reinforcing rod, the bit will stop

immediately and the rotary hammer

will react to revolve. Therefore please

grip the side handle and handle tightly

as shown in Fig. 6.

mark. (Fig. 5)

English

Push Button

Change Lever

Fig. 5

Fig. 6

Push Button

3. Rotation only

This rotary hammer can be set to

rotation only mode by pressing the

push button and turning the change

lever to

To drill a wood or metal material using

the separately sold drill chuck and

chuck adaptor, proceed as follows.

Installing drill chuck and chuck adaptor

(Fig. 8): (1) Mount the drill chuck to the chuck

adaptor. (2) The part of the SDS-plus shank is the

same as the drill bit. Therefore, refer

to the item of “Mounting the drill bit”

for attaching it.

mark. (Fig. 7)

Drill Chuck

Chuck Adaptor

Change Lever

Fig. 7

Front Cap

Part of SDS-plus shank

Fig. 8

Grip

English

CAUTION:

䡬 Application of force more than necessary will not only reducing drilling efficiency

at all, but will deteriorate the tip edge of the drill bit and reduce the service life

of the rotary hammer in addition. 䡬 Drill bit may snap off while disengaging the rotary hammer from the jammed

hole. For disengaging, it is important to use a pushing motion or turn the drill

bit counterclockwise. 䡬 Do not attempt to drill anchor holes or holes in concrete with the main unit in

the rotation only function. 䡬 Do not attempt to use the rotary hammer in the rotation and striking function

with the drill chuck and chuck adaptor attached. This would seriously shorten

the service life of every components of the machine.

4. When driving machine screws

(Fig. 9)

First, insert the bit into the socket in

the end of chuck adaptor (D).

Next, mount chuck adaptor (D) on the

main unit using procedures described

in 6 (1), (2), (3), put the tip of the bit in

the slots in the head of the screw,

grasp the main unit and tighten the

screw.

CAUTION:

䡬 Exercise care not to excessively

prolong driving time, otherwise, the

screws may be damaged by excessive

force. 䡬 Apply the rotary hammer perpendicularly to the screw head when driving a

screw; otherwise, the screw head or bit will be damaged, or driving force will

not be fully transferred to the screw. 䡬 Do not attempt to use the rotary hammer in the rotation and striking function

with chuck adaptor (D) and bit attached.

Bit

Socket

Chuck Adaptor (D)

Front Cap

Grip

Fig. 9

5. When driving wood screws (Fig. 9)

(1) Selecting a suitable driver bit

Employ phillips screws, if possible, since the driver bit easily slips off the heads

of slotted-head screws. (2) Driving in wood screws 䡬 Prior to driving in wood screws, make pilot holes suitable for them in the wooden

board. Apply the bit to the screw head grooves and gently drive the screws into

the holes. 䡬 After rotating the rotary hammer at low speed for a while until a wood screw in

partly driven into the wood, squeeze the trigger more strongly to obtain the

optimum driving force.

English

CAUTION:

䡬 Exercise care in preparing a pilot hole suitable for the wood screw taking the

hardness of the wood into consideration. Should the hole be excessively small

or shallow, requiring much power to drive the screw into it, the thread of the

wood screw may sometimes be damaged.

Change Lever

6. Striking only (DH30PC)

This rotary hammer can be set to

striking only mode by pressing the

push button and turning the change

lever to

mark. (Fig. 10) (1) Mount the bull point or cold chisel. (2) Press the push button and set the

change lever to

mark or mark. Then rotation is released, turn the grip and adjust the cold chisel to desired position. (Fig. 11)

(3) Turn the change lever to

mark. (Fig.

Push Button

Fig. 10

10) Then bull point or cold chisel is locked.

7. Using the stopper (Fig. 12)

(1) Loosen the side handle, and insert the

stopper into the handle bolt hole.

(2) Adjust the stopper position according

to the depth of the hole and tighten

Grip

the side handle securely.

8. How to use the drill bit (taper

Fig. 11

shank) and the taper shank adaptor.

(1) Mount the taper shank adaptor to the

rotary hammer. (Fig. 13)

(2) Mount the drill bit (taper shank) to the

taper shank adaptor. (Fig. 13)

(3) Turn the switch ON, and drill a hole in

prescribed depth.

(4) To remove the drill bit (taper shank),

insert the cotter into the slot of the taper shank adaptor and strike the head of the cotter with a manual hammer supporting on the rests. (Fig.

14)

Stopper

Handle Bolt

Knob on Side Handle

Fig. 12

English

9. Using the side handle

When you wish to change a position of the side handle, turn grip of the side handle counterclockwise to loosen it, and then fasten it firmly.

CAUTION:

When boring a hole, there can be a case where the machine attempts to rotate by the reaction at the time of penetrating a concrete wall and/or when a tip of the blade comes in contact with the rebar. Firmly fasten the side handle and hold the machine with both of your hands. Unless you hold it securely, an accident can occur.

Drill Bit

Taper shank Adaptor

Cotter

Fig. 14

Front Cap Grip

Fig. 13

Taper Shank Adaptor

Rests

HOW TO USE THE CORE BIT (FOR LIGHT LOAD)

When boring penetrating large hole use the core bit (for light load). At that time use with the center pin and the core bit shank provided as optional accessories.

1. Mounting

CAUTION:

䡬 Be sure to turn power OFF and disconnect the plug from the receptacle.

(1) Mount the core bit to the core bit

shank. (Fig. 15) Lubricate the thread of the core bit shank to facilitate disassembly.

(2) Mount the core bit shank to the rotary

hammer. (Fig. 16)

(3) Insert the center pin into the guide

plate until it stops.

Core Bit

Thread

Core Bit Shank

Fig. 15

English

(4) Engage the guide plate with the core bit, and turn the guide plate to left or right

so that it does not fall even if it faced downward. (Fig. 17)

Guide Plate

Center Pin

Core Bit

Core Bit Tip

Fig. 16 Fig. 17

2. How to bore (Fig. 18)

(1) Connect the plug to the power source. (2) A spring is installed in the center pin.

Push it lightly to the wall or the floor perpendicularly. Connect all over the surface of the core bit tip and start operating.

(3) When boring about 3/16" (5 mm) in

depth the position of the hole will establish. Bore after that removing the center pin and the guide plate from core bit.

(4) Application of excessive force will not only expedite the work, but will deteriorate

the tip edge of the drill bit, resulting in reduced service life of the rotary hammer.

CAUTION:

䡬 When removing the center pin and the guide plate, turn OFF the switch and

disconnect the plug form the receptacle.

Fig. 18

3. Dismounting. (Fig. 19)

Remove the core bit shank from the rotary hammer and strike the head of the core bit shank strongly two or three times with the manual hammer holding the core bit, then the thread becomes loose and the core bit can be removed.

Core Bit shank

Fig. 19

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted.

2. Inspecting the screws

Regularly inspect all screws and ensure that they are properly tightened. Should any of the screws be loosened, retighten them immediately.

WARNING: Using this rotary hammer with loosened screws is extremely

dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes: (Fig. 20)

The motor employs carbon brushes which are consumable parts. When they become worn to or near “wear limit”, it could result in motor trouble. When an auto-stop carbon brush is equipped, the motor will stop automatically. At that time, replace both carbon brushes with new ones which have the same carbon brush Nos. shown in the figure. In addition, always keep carbon brushes clean and ensure that they slide freely within the brush holders.

CAUTION: Using this rotary hammer with a carbon brush which is worn in

excess of the wear limit will damage the motor.

Wear limit

No. of carbon brush

0.28" (7 mm)

0.67" (17 mm)

Fig. 20

NOTE: Use HITACHI carbon brush No.73 indicated in Fig. 20.

䡬 Replacing carbon brushes:

(For parts name, refer to Fig. 1) Loosen the two set screws and remove the tail cover. Remove the brush caps and carbon brushes. After replacing the carbon brushes, tighten the brush caps securely and to install the tail cover with securely tightening two set screws.

5. How to replase grease

This machine is full air-tight construction to protect against dust and to prevent lubricant leakage. Therefore, the machine can be used without lubrication for long periods. Replace the grease as described below.

䡬 Grease replacement period

You should look at the grease when you change the carbon brush. (See item 4 in the section MAINTENANCE AND INSPECTION.) Ask for grease replacement at the nearest HITACHI Authorized Service Center. Proceed for replacement of grease.

䡬 Grease replenishment

CAUTION: Before replenishing the grease, turn the power off and pull out the

power plug.

English

(1) Disassemble the crank cover and

thoroughly wipe off the old grease inside. (FIg. 21)

(2) Supply 30g (the standard volume to

cover the connecting rod) of Hitachi Electric Hammer Grease A in the crank case.

(3) After replacing the grease, reassemble

the crank cover securely. At this time, do not damage or lose the oil seal.

NOTE: The HITACHI Electric Hammer

Grease A is of the lower viscosity type. When the supplied grease tube is consumed, purchase from a HITACHI Autorized Service Center.

Crank Case Cover

Fig. 21

6. Service and repairs

All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY.

English

ACCESSORIES

WARNING: ALWAYS use Only authorized HITACHI replacement parts and

accessories. NEVER use replacement parts or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1) Case (Molded plastic) (Code No. 307786).............................................................1

(2) Side Handle (Code No. 303659).............................................................................1

(3) Stopper (Code No. 971786)....................................................................................1

(4) Dust Cup (Code No. 971787)..................................................................................1

(5) Syringe (Code No. 318085) ....................................................................................1

OPTIONAL ACCESSORIES........sold separately

1. Drilling anchor holes (Rotation + Striking)

䡬 Drill Bit (Taper shank) and taper shank adaptor

(1) Drill Bit (Taper Shank)

(2) Taper Shank Adaptor

(SDS-plus shank)

Cotter (Code No. 944477)

English

External dia. Code No.

7/16"

(11 mm)

31/64"

(12.3 mm)

1/2"

(12.7 mm)

9/16"

(14.3 mm)

73/128"

(14.5 mm)

11/16"

(17.5 mm)

27/32"

(21.5 mm)

944460

944461

993038

944462

944500

944463

944464

Taper mode Code No. Applicable drill bit

7/16" (11 mm)

31/64" (12.3 mm)

1/2" (12.7 mm)

9/16" (14.3 mm)

73/128" (14.5 mm)

11/16" (17.5 mm)

Morse taper

(No. 1)

Morse taper

(No. 2)

A-taper 303619

B-taper 303620

303617

303618 27/32" (21.5 mm)

Drill bit

(Taper shank)

Drill bit

(Taper shank)

Taper shank adaptor formed Ataper or B-taper is provided as an optional accessory, but drill bit for it is not provided.

2. Knock-in anchor (Striking only) (DH30PC)

Anchor Setter (for anchor setting) (SDS-plus shank)

nchor size

Overall Length

Code No. 302976 302975 303621 302974

W 1/4" W 5/16" W 3/8"

(6.3 mm) (8 mm) (9.5 mm)

10-15/64" 10-15/64" 6-19/64" 10-15/64"

(260 mm) (260 mm) (160 mm) (260 mm)

nchor size

Overall Length

Code No. 302979 302978 303622 302977

W 1/4" W 5/16" W 3/8"

(6.3 mm) (8 mm) (9.5 mm)

10-15/64" 10-15/64" 6-19/64" 10-15/64"

(260 mm) (260 mm) (160 mm) (260 mm)

Anchor setting adaptor (for manual hammer)

English

<Outer wedge type with

the female screw>

Anchor size Code No.

W1/4"

(6.3 mm)

W5/16" (8 mm)

W3/8"

(9.5 mm)

W1/2"

(12.7 mm)

W5/8"

(15.9 mm)

971794

971795

971796

971797

971798

<Inner wedge type with

the headless screw>

Anchor size Code No.

W1/4"

(6.3 mm)

W5/16"

(8 mm)

W3/8"

(9.5 mm)

W1/2"

(12.7 mm)

W5/8"

(15.9 mm)

3. Large hole boring (Rotation + Striking)

Guide Plate

Center pin Core Bit

Center

Code No.

––

(A) 982684 1-3/8" (35 mm) 982675 11-13/18"

(B) 982685 (B) 2-9/16" (65 mm) 982679 (B)

Core bit (outer diameter) Core bit shank

63/64"(25 mm) 982672 Overall length

1-9/64" (29 mm) 982673 4-1/8" 303625

(A) 1-1/4" (32 mm) 982674 (A) (105 mm)

1-1/2" (38 mm) 982676 (300 mm) 1-25/32" (45 mm) 982677 1-31/32" (50 mm) 982678

3-5/32" (80 mm) 982680

3-17/32" (90 mm) 982681

Core bit Shank (SDS-plus shank)

Code No. Code No.

11-13/18" (300 mm)

971799

971800

971801

971802

971803

303626

303627

Guide plate

Core bit

(outer diameter)

1-1/4" (32 mm) 1-3/8" (35 mm) 1-1/2" (38 mm)

1-25/32" (45 mm)

Code No.

982686 982687 982688 982689

Core bit

(outer diameter)

1-31/32" (50 mm)

2-9/16" (65 mm) 3-5/32" (80 mm)

3-17/32" (90 mm)

Code No.

982690 982691 982692 982693

4. Demolishing operation (Striking only)(DH30PC)

Bull point (Round type) (SDS-plus shank) Code No. 303046

Bull point (Square type) (SDS-plus shank) Code No. 316656

5. Groove digging and edging (Striking only)(DH30PC)

Cold chisel (SDS-plus shank) Code No. 316657

Cutter (SDS-plus shank) Code No. 316658

6. Grooving (Striking only)(DH30PC)

Grooving Chisel (SDS-plus shank)(DH30PC) Code No. 316659

English

7. Bolt placing operation with Chemical Anchor. (Rotation + Striking)

Standard socket

(

on the market

(SDS-plus shank)

)

1/2" (12.7 mm) Chemical Anchor Adapter

3/4" (19 mm) Chemical Anchor Adapter

(Code No.303044)

(Code No. 303045)

+ 53 hidden pages