Hitachi CP-X200, CP-X300, CP-X400 User Manual

Download

Page 1

Projector

CP-X200/CP-X300/CP-X400

User's Manual (detailed) Operating Guide

Thank you for purchasing this projector.

WARNING ►Before using this product, please read all manuals for this

product. Be sure to read “Safety Guide” rst. After reading them, store them in a safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING This symbol indicates information that, if ignored, could possibly

result in personal injury or even death due to incorrect handling.

CAUTION This symbol indicates information that, if ignored, could possibly

result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



NOTE • The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgment

• Mac is registered trademarks of Apple Computer, Inc.

• VESA and SVGA are trademarks of the Video Electronics Standard Association.

• Windows is a registered trademark of Microsoft Corporation.

All other trademarks are the properties of their respective owners.

Page 2

Content

 

About this manual . . . . . . . . . . 1

Content . . . . . . . . . . . . . . . . . . 2

Projector features . . . . . . . . . . 3

Preparations . . . . . . . . . . . . . . 3

Contents of package . . . . . . . . . . . . .3

Fastening the lens cover . . . . . . . . . .3

Part names . . . . . . . . . . . . . . . 4

Projector . . . . . . . . . . . . . . . . . . . . . .4

Control panel . . . . . . . . . . . . . . . . . . .5

Rear panel . . . . . . . . . . . . . . . . . . . . .5

Remote control . . . . . . . . . . . . . . . . .6

Setting up . . . . . . . . . . . . . . . . 7

Arrangement . . . . . . . . . . . . . . . . . . .7

Connecting your devices . . . . . . . . .10

Connecting power supply . . . . . . . .12

Using the security bar and slot . . . .12

Remote control . . . . . . . . . . . 13

Putting batteries . . . . . . . . . . . . . . .13

About the remote control signal . . . .13

Changing the frequency of remote

control signal

Using as a

simple PC mouse & keyboard . . .14

Power on/off . . . . . . . . . . . . . 15

Turning on the power . . . . . . . . . . . .15

Turning off the power . . . . . . . . . . . .15

Operating . . . . . . . . . . . . . . . 16

Adjusting the volume . . . . . . . . . . . .16

Temporarily muting the sound . . . . .16

Selecting an input signal . . . . . . . . .16

Searching an input signal . . . . . . . .17

Selecting an aspect ratio . . . . . . . . .17

Adjusting the projector's elevator . .18

Adjusting the zoom and focus . . . . .18

Using the automatic adjustment feature

Adjusting the position . . . . . . . . . . .19

Correcting the keystone distortions

Using the magnify feature . . . . . . . .20

Freezing the screen . . . . . . . . . . . . .21

Temporarily blanking the screen . . .21

Using the menu function . . . . . . . . .22

. . . . . . . . . . . . . . . . .14

. .19

. .20

EASY MENU. . . . . . . . . . . . . . 24

spect

, A

eystone

ontrast

hisper

anguage

uto keystone

, P

, C

olor

, M

irror

, G

o to Advanced Menu...

icture mode

, T

int

, S

harpness

, R

eset

, F

execute

, B

rightness

ilter time

PICTURE menu . . . . . . . . . . . 26

Brightness, Contrast, Gamma, Color temp, Color, Tint, Sharpness, My memory

IMAGE menu . . . . . . . . . . . . . 29

Aspect, Over scan, V position, H position, H phase, H size, Auto adjust execute

INPUT menu . . . . . . . . . . . . . 31

rogressive

omponent

rame lock

esolution

, V

ideo nr

, V

ideo format

, C

omputer in

, C

olor space

SETUP menu . . . . . . . . . . . . . 34

uto keystone

hisper

peaker

, M , A

irror

udio

, V

execute

olume

, K

eystone

SCREEN menu . . . . . . . . . . . . 36

Language, Menu position, Blank, Start up, M

yScreen

, M

yScreen Lock

Message, Source name

OPTION menu . . . . . . . . . . . . 40

Auto search, Auto keystone , Auto on, Auto off, Lamp time, Filter time, My button, Service,

Security

Maintenance . . . . . . . . . . . . . 51

Lamp . . . . . . . . . . . . . . . . . . . . . . . .51

Air lter . . . . . . . . . . . . . . . . . . . . . .53

Other care . . . . . . . . . . . . . . . . . . . .54

Troubleshooting . . . . . . . . . . 55

Related messages . . . . . . . . . . . . . .55

Regarding the indicator lamps . . . . .56

Shutting the projector down . . . . . . .57

Resetting all settings . . . . . . . . . . . .57

Phenomena that may be easy

to be mistaken for machine defects

. .58

Specications . . . . . . . . . . . . 60

Page 3

Projector features / Preparations

Projector features

This projector has a capability to project various picture signals onto a screen. This projector requires only a minimal amount of space for installation and can produce a large projected image from even a short distance. This projector boasts a variety of I/O port and low noise. These features provide you with the broad use of this projector.

Preparations

Contents of package

Please see the “Contents of package” in the “User’s Manual (concise)” which is a book. Your projector should come with the items shown there. Contact immediately your dealer if anything is missing.

NOTE • Keep the original packing materials, for future reshipment. Be sure to use the original packing materials when moving the projector. Use special caution for the lens.

Fastening the lens cover

To avoid losing the lens cover, please fasten the lens cover to the projector using the enclosed strap.

Fix the strap to the strap hole of the lens cover.

Thread one end of the strap through the strap hole of the lens cover and make the loop at the end, and let the other end of the strap through the loop. Not have a knot in the strap at either end.

Fix the strap to the strap hole of the projector.

Thread the other end of the strap through the strap hole of the projector and make

the loop there. Let the lens cover with the one end of strap though the loop.

Page 4

Part names

Projector

(1) (2) (3) (4)

HOT!

(1) Lamp cover (

The lamp unit is inside. (2) Focus ring ( (3) Zoom ring ( (4) Control panel ( (5) Elevator buttons (x 2) ( (6) Elevator feet (x 2) ( (7) Remote sensor ( (8) Lens ( (9) Lens cover ( (10) Intake vents (11) Filter cover (

(12) Speaker ( (13) Exhaust vent (14) AC inlet ( (15) Power switch ( (16) Rear panel ( (17) Security bar ( (18) Security slot (



The air lter and intake vent are inside.



18, 54)



35)

12)



18)



51)



53)



13)

15)

12)



18)

(6)

(9)

HOT!

(18)

(8)

(13)

(16)

(4)

(17)

(6)

(7)

(13)

(6)

(1)

(5)

(12)

(11)

(10)

(6)

(10)

(11)

(14)

(15)

WARNING ►HOT! : Do not touch around the lamp cover and the exhaust

vents during use or just after use, since it is too hot. ►Do not look into the lens or vents while the lamp is on, since the strong light is not good for your eyes. ►Do not handle the elevator buttons without holding the projector, since the projector may drop down.

CAUTION ►

Maintain normal ventilation to prevent the projector from heating up. Do not cover, block or plug up the vents. Do not place anything that can stick or be sucked to the vents, around the intake vents. Clean the air lter periodically.

Page 5

Part names

Control panel

(1) STANDBY/ON button ( (2) INPUT button ( (3) MENU button (

It consists of four cursor buttons. (4) POWER indicator ( (5) TEMP indicator ( (6) LAMP indicator (

 

16, 22)

22)



56)



56)



15, 56)

Rear panel

(1) AUDIO IN1 port ( (2) AUDIO IN2 port ( (3) AUDIO OUT port ( (4) COMPUTER IN1 port ( (5) COMPUTER IN2 port ( (6) MONITOR OUT port ( (7) Shutdown switch (

 



10)

 



57)

10)

15)

10)

(8) CONTROL port ( (9) USB port (

(10) COMPONENT

(Y, Cb/Pb, Cr/Pr) port ( (11) VIDEO port ( (12) S-VIDEO port ( (13) AUDIO IN3 (L,R) ports (

(1)

(3) (4) (7)

(10)

(6) (5) (4)

(1) (2)(3)

10)



10)



10)



10)



(6)(5)



10)

(2)

(9)(8) (11)

(12)(13)

CAUTION ►Do not use the security bar and slot to prevent the projector

from falling down, since it is not designed for it. ►Use the shutdown switch only when the projector is not turned off by normal procedure, since pushing this switch stops operation of the projector without cooling it down.

Page 6

Part names

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

Remote control

(1) VIDEO button (

(2) COMPUTER button (

(3) SEARCH button (

(4) STANDBY/ON button (

(5) ASPECT button (

(6) AUTO button (

(7) BLANK button (

(8) MAGNIFY - ON button (

(9) MAGNIFY - OFF button (

(10) HOME button (

(11) END button (

(12) PAGE UP button (

(13) PAGE DOWN button (

(14) VOLUME button (

(15) MUTE button (

(16) FREEZE button (

(17) MY BUTTON - 1 button (

(18) MY BUTTON - 2 button (

(19) KEYSTONE button (

(20) POSITION button (

(21) MENU button (

(22) ▲/▼/◄/► cursor buttons (

(23) ENTER button (

(24) ESC button (

(25) RESET button (

(26) Battery cover (



17)



19)

21)



14)



14, 22)



16)



17)



17)



14)



16)



14, 16)

21)



19, 22)



22)

14, 22, 23)

13)

15)



14)

 

20)

20) 14, 20)

42)



14, 22, 23)

(2) (1) (5)

(10)

(8)

(9) (11) (16) (17) (20) (22)

(24)

the remote control

(3) (4) (6)

(7) (12) (14) (15) (13) (19) (18) (21) (23) (25)

Back of

(26)

Page 7

Setting up

Install the projector according to the environment and manner the projector will be used in.

Arrangement

Refer to the illustrations and tables below to determine screen size and projection distance.

<CP-X200 / CP-X400>

The values shown in the table are calculated for a full size screen: 1024×768. (a) Screen size (diagonal) (b) Projection distance (±10%) (c1), (c2) Screen height (±10%)

On a horizontal surface

Suspended from the ceiling

• Keep a space of 30 cm or more between the sides of the projector and other objects such as walls.

• Consult with your dealer before a special installation such as suspending from a ceiling.

Screen size

(diagonal)

inch m m inch m inch cm inch cm inch m inch m inch cm inch cm inch

30 0.8 0.9 34 1.1 41 41 16 5 2 1.0 38 1.1 45 39 15 -1 0 40 1.0 1.2 46 1.4 56 55 22 6 2 1.3 50 1.5 61 51 20 -2 -1 50 1.3 1.5 58 1.8 70 69 27 8 3 1.6 63 1.9 76 64 25 -2 -1 60 1.5 1.8 70 2.1 84 82 32 9 4 1.9 76 2.3 91 77 30 -2 -1 70 1.8 2.1 81 2.5 98 96 38 11 4 2.3 89 2.7 107 90 35 -3 -1 80 2.0 2.4 93 2.8 112 110 43 12 5 2.6 102 3.1 122 103 41 -3 -1

90 2.3 2.7 105 3.2 126 123 49 14 5 2.9 115 3.5 138 116 46 -4 -1 100 2.5 3.0 117 3.6 140 137 54 15 6 3.2 127 3.9 153 129 51 -4 -2 120 3.0 3.6 140 4.3 169 165 65 18 7 3.9 153 4.7 184 154 61 -5 -2 150 3.8 4.5 176 5.4 211 206 81 23 9 4.9 192 5.8 230 193 76 -6 -2 200 5.1 6.0 235 7.2 282 274 108 30 12 6.5 256 7.8 307 257 101 -8 -3 250 6.4 7.5 294 9.0 353 343 135 38 15 8.1 320 9.8 384 322 127 -10 -4 300 7.6 9.0 352 10.8 423 411 162 46 18 9.8 384 11.7 461 386 152 -12 -5

Projection distance

min. max.

4 : 3 screen 16 : 9 screen

c1 c2

Screen

height

Screen

height

Projection distance

min. max.

Screen

height

Screen

height

Page 8

Setting up

Arrangement (continued)

<CP-X300>

The values shown in the table are calculated for a full size screen: 1024×768. (a) Screen size (diagonal) (b) Projection distance (±10%) (c1), (c2) Screen height (±10%)

On a horizontal surface

Suspended from the ceiling

• Keep a space of 30 cm or more between the sides of the projector and other objects such as walls.

• Consult with your dealer before a special installation such as suspending from a ceiling.

Screen size

(diagonal) inch m m inch m inch cm inch cm inch m inch m inch cm inch cm inch

30 0.8 0.9 35 1.1 43 41 16 5 2 1.0 39 1.2 47 39 15 -1 0

40 1.0 1.2 47 1.4 57 55 22 6 2 1.3 52 1.6 62 51 20 -2 -1

50 1.3 1.5 59 1.8 71 69 27 8 3 1.6 65 2.0 78 64 25 -2 -1

60 1.5 1.8 71 2.2 86 82 32 9 4 2.0 78 2.4 94 77 30 -2 -1

80 2.0 2.4 95 2.9 115 110 43 12 5 2.6 104 3.2 125 103 41 -3 -1

90 2.3 2.7 107 3.3 129 123 49 14 5 3.0 117 3.6 141 116 46 -4 -1 100 2.5 3.0 119 3.6 144 137 54 15 6 3.3 130 4.0 156 129 51 -4 -2 120 3.0 3.6 143 4.4 172 165 65 18 7 4.0 156 4.8 188 154 61 -5 -2 150 3.8 4.6 179 5.5 216 206 81 23 9 4.9 195 6.0 235 193 76 -6 -2 200 5.1 6.1 239 7.3 288 274 108 30 12 6.6 261 8.0 314 257 101 -8 -3 250 6.4 7.6 299 9.1 360 343 135 38 15 8.3 326 10.0 392 322 127 -10 -4 300 7.6 9.1 359 11.0 432 411 162 46 18 9.9 391 12.0 471 386 152 -12 -5

Projection distance

min. max.

1.8 2.1 83 2.5 100 96 38 11 4 2.3 91 2.8 109 90 35 -3 -1

4 : 3 screen

Screen

height

c1 c2

Screen

height

Projection distance

min. max.

16 : 9 screen

Screen

height

Screen

height

Page 9

Setting up

WARNING ►Place the projector in a stable horizontal position. If the

projector falls or is knocked over it could cause injury and/or damage to the projector. Using a damaged projector could then result in re and/or electric shock.

• Do not place the projector on an unstable, slanted or vibrational surface such

as a wobbly or inclined stand.

• Do not place the projector on its side, front or rear position.

• Consult with your dealer before a special installation such as suspending

from a ceiling. ►Place the projector in a cool place, and ensure that there is sufcient ventilation. The high temperature of the projector could cause re, burns and/ or malfunction of the projector.

• Do not stop-up, block or otherwise cover the projector's vents.

• Keep a space of 30 cm or more between the sides of the projector and other

objects such as walls.

• Do not place the projector on metallic thing or anything weak in heat.

• Do not place the projector on carpet, cushions or bedding.

• Do not place the projector in direct sunlight or near hot objects such as

heaters.

• Do not anything near the projector lens or vents, or on top of the projector.

• Do not place anything that may be sucked into or stick to the vents on the

bottom of the projector. This projector has some intake vents also on the

bottom. ►Do not place the projector anyplace where it may get wet. Getting the projector wet or inserting liquid into the projector could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector in a bathroom or the outdoors.

• Do not place anything containing liquid near the projector.

CAUTION ►Avoid placing the projector in smoky, humid or dusty place.

Placing the projector in such places could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector near humidiers, smoking spaces or a kitchen. ►Position the projector to prevent light from directly hitting the projector's remote sensor.

Page 10

Setting up

AUDIO IN

Y CB/PB CR/PR

COMPONENT VIDEO OUT

L R

AUDO IN OUT

VIDEO OUT

L R

AUDO IN OUT

L R

AUDO IN OUT

S-VIDEO OUT

AUDIO OUT

RGB OUT

AUDIO OUT

USB

RGB OUT

RS-232C

RGB IN

Connecting your devices

Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them.

Speakers

VCR/DVD

player

Monitor

WARNING ►Do not disassemble or modify the projector and accessories.

►Be careful not to damage the cables, and do not use damaged cables.

CAUTION ►Turn off all devices and unplug their power cords prior to

connecting them to projector. Connecting a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction or damage to the device and the projector. ►Use appropriate accessory or otherwise designed cables. Ask your dealer about non-accessory cables which may have to be of a specic length or equipped with a core. For cables with a core only at one end, connect the end with the core to the projector. ►Make sure that devices are connected to the correct ports. An incorrect connection may result in malfunction or damage to the device and the projector.

Page 11

Setting up

Connecting your devices (continued)

NOTE • Be sure to read the manuals for devices before connecting them to the

projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution.

- Some signal may need an adapter to input this projector.

- Some PCs have multiple screen display modes that may include some signals which are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA (1600X1200),

the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical.

• While connecting, make sure that the shape of the cable's connector ts the port to

connect with. And be sure to tighten the screws on connectors with screws.

• When connecting a laptop PC to the projector, be sure to activate the PC’s external

RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT display.) For details on how this is done, please refer to the instruction manual of the corresponding laptop PC.

• When the picture resolution is changed on a pc depending on an input, automatic

adjustment function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution.

• In some cases, this projector may not display a proper picture or display any picture on

screen. For example, automatic adjustment may not function correctly with some input signals. An input signal of composite sync or sync on G may confuse this projector, so the projector may not display a proper picture.

About Plug-and-Play capability

Plug-and-Play is a system composed of a PC, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-andPlay can be used by connecting this projector to a pc that is VESA DDC (display data channel) compatible.

• Take advantage of this feature by connecting an RGB cable to the COMPUTER IN1

port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

• Please use the standard drivers in your pc as this projector is a Plug-and-Play monitor.

Page 12

Setting up

Connecting power supply

At rst, make sure that the power switch of the projector is set to OFF position (marked "O").

Put the connector of the power cord into

the AC inlet of the projector. Firmly plug the power cord’s plug into the

outlet.

AC inlet

WARNING ►Please use extra caution when connecting the power cord, as

incorrect or faulty connections may result in re and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, contact

your dealer to newly get correct one.

• Only plug the power cord into an outlet rated for use with the power cord's

specied voltage range. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

• Never modify the power cord.

Power cord

Using the security bar and slot

A commercial anti-theft chain or wire up to 10 mm in diameter can be attached to the security bar on the projector. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool.

WARNING ►Do not use the security bar and slot to prevent the projector

from falling down, since it is not designed for it.

CAUTION ►Do not place anti-theft chain or wire near the exhaust vents. It

may become too hot.

NOTE • The security bar and slot is not comprehensive theft prevention

measures. It is intended to be used as supplemental theft prevention measure.

Page 13

Remote control

Putting batteries

Please set the batteries to the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

Holding the hook part of the battery

cover, remove it. Align and insert the two AA batteries

according to their plus and minus terminals

as indicated in the remote control.

Replace the battery cover in the direction of the arrow and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as

directed. Improper use may result in battery explosion, cracking or leakage, which could result in re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different

types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not allow a battery in a re or water. Keep batteries in a dark, cool and dry place.

•

If you observe battery leakage, wipe out the leakage and then replace a battery. If the

leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

About the remote control signal

The remote control w or ks with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active: 60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

NOTE • The remote control signal reected in the screen or the like may

be available. If it is difcult to send the signal to the sensor directly, attempt to make the signal reect.

• The remote control uses infrared light to send signals to the projector (Class 1 LED),

so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter uorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

Approx.

3 m

30º

Page 14

Remote control

USB

USB STORAGE

AUDIO OUT

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency. In order to set the Mode, please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds. (1) Set to Mode 1:NORMAL... MUTE and RESET buttons (2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons Please remember that the REMOTE FREQ. in the SERVICE item of the OPTION menu (

44) of the projector to be controlled



should be set to the same mode as the remote control.

Using as a simple PC mouse & keyboard

The enclosed remote control works as a simple mouse and keyboard of the PC, when the projector's USB port (B type) connects with the PC's USB port (A type) port via a mouse cable.

(1) HOME key: Press HOME button. (2) END key: Press END button. (3) PAGE UP key: Press PAGE UP button. (4) PAGE DOWN key: Press PAGE DOWN button. (5) Mouse left button: Press ENTER button. (6) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►. (7) ESC key: Press ESC button. (8) Mouse right button: Press RESET button.

USB port

(2)

(1)(2)

(3)(1)

(4)

CAUTION ►Improper use of the simple mouse

& keyboard function could damage your equipment.

(5)

While using this function, please connect this product only to a PC. Be sure to check your PC’s manuals

(7)

before connecting this product to the PC.

NOTE •

When the simple mouse & keyboard function of this product does not work

correctly, please check the following.

- When the mouse cable connects this projector with a PC having a built-in pointing device (e.g. track ball) like a notebook PC, open BIOS setup menu, then select the external mouse and disable the built-in pointing device, because the built-in pointing device may have priority to this function.

- Windows 95 OSR 2.1 or higher is required for this function. And also this function may not work depending on the PC’s congurations and mouse drivers.

- You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

- This function is activated only when the projector is working properly. This function is not available while the lamp is warming up (the POWER indicator blinks green), and while adjusting the volume and display, correcting for keystone, zooming in on the

screen, using the BLANK function, or displaying the menu screen.

(6)

(8)

Page 15

Power on/off

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

Power on/off

Turning on the power

Make sure that the power cord is rmly and correctly

connected to the projector and the outlet. Remove the lens cover, and set the power switch to

ON position (marked “ I “).

The POWER indicator will light up in steady orange (

56). Then wait several seconds because the



buttons may not function for these several seconds.

Press STANDBY/ON button on the projector or the

remote control.

The projection lamp will light up and POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green (



56).

To display the picture, select an input signal according to the section “Selecting an input signal” (



16).

Turning off the power

Press the STANDBY/ON button on the projector or the remote control. The message

“Power off?” will appear on the screen for about 5 seconds.

Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete(

Make sure that POWER indicator lights in steady orange, and set the

power switch to OFF position (marked “O“).

POWER indicator will go off. Attach the lens cover.

Do not turn the projector on for about 10 minutes or more after turning it off. Turning the projector on again too soon could shorten the lifetime of some consumable parts of the projector.



56).

WARNING

►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings. ►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE • Turn the power on/off in right order. Please power on the projector prior

to the connected devices. Power off the projector after all of connected devices are powered off.

•

The projector has the AUTO ON function, which can make the projector automatically

turn on. For more information, please see AUTO ON item of OPTION menu

• Use the shutdown switch (57) only when the projector is not turned off by

normal procedure.

(



40).

Page 16

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

COMPUTER

Operating

Adjusting the volume

Press VOLUME button on the remote control.

A dialog will appear on the screen to aid you in adjusting the

volume.

Use the ▲/▼ cursor buttons to adjust the volume.

To close the dialog and complete the operation, press the VOLUME button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● When is selected for current picture input port, the volume adjustment is disable. Please see AUDIO item of SETUP menu

(

35)



▲/▼

Temporarily muting the sound

Press MUTE button on the remote control.

A dialog will appear on the screen indicating that you have muted the sound. To restore the sound, press the MUTE or VOLUME button. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● When is selected for current picture input port, the sound is

(

35)

always muted. Please see AUDIO item of SETUP menu



Selecting an input signal

Press INPUT button on the projector.

Each time you press the button, the projector switches its input port as below.

COMPUTER IN 1  COMPUTER IN 2 VIDEO  S-VIDEO



COMPONENT (Y, Cb/Pb, Cr/Pr)

VOLUME

MUTE

Press COMPUTER button on the remote control.

Each time you press the button, the projector switches its input port as below.

COMPUTER IN 1  COMPUTER IN 2

●

If COMPUTER button is pushed to switch from a signal from VIDEO, S-VIDEO or COMPONENT port, when TURN ON is selected for AUTO SEARCH item in OPTION menu projector will check COMPUTER IN1 port rst. If no input is detected at the port, the projector will check COMPUTER IN2 port.

(continued on next page)

COMPUTER

(

40)



, the

Page 17

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

COMPUTER

Selecting an input signal (continued)

Press VIDEO button on the remote control.

Each time you press the button, the projector switches its input port as below.

COMPONENT(Y, Cb/Pb, Cr/Pr)  S-VIDEO  VIDEO

● If VIDEO button is pushed to switch from a signal from COMPUTER IN1 or 2 port, when TURN ON is selected for AUTO

(

40)

SEARCH item in OPTION menu



, the projector will check COMPONENT port rst. If no input is detected at the port, the projector will check the other port in above order.

Searching an input signal

Press SEARCH button on the remote control.

The projector will start to check its input ports in order to nd any input signals. When an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

COMPUTER IN 1  COMPUTER IN 2 VIDEO  S-VIDEO

Selecting an aspect ratio

Press ASPECT button on the remote control.

Each time you press the button, the projector switches the



COMPONENT (Y, Cb/Pb, Cr/Pr)

mode for aspect ratio in turn.

For a computer signal



NORMAL

4:3  16:9  SMALL



For a video signal, s-video signal or component video



signal

4:3  16:9  14:9  SMALL

For no signal



4:3 (xed)

● ASPECT button does not work when no proper signal is inputted.

● NORMAL mode keeps the original aspect ratio setting.

VIDEO

ASPECT

Page 18

Operating

Adjusting the projector's elevator

When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 10 degrees. This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is adjustable while pushing the elevator button on the same side as it.

Holding the projector, push the elevator buttons to loose the elevator feet.

Position the front side of the projector to the desired height.

Release the elevator buttons in order to lock the elevator feet.

After making sure that the elevator feet are locked, put the projector gently.

If necessary, the elevator feet can be manually twisted to make more precise

adjustments. Hold the projector when twisting the feet.

To loose an elevator foot, push the elevator button on the same side as it.

CAUTION ►Do not handle the elevator buttons without holding the

projector, since the projector may drop down. ►Do not tilt the projector other than it elevating its front within 10 degrees using the adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables, or the projector itself.

Adjusting the zoom and focus

Use the zoom ring to adjust the screen size.

Use the focus ring to focus the picture.

To nely adjust, twist the foot.

Focus ring

Zoom ring

Page 19

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

COMPUTER

Using the automatic adjustment feature

Press AUTO button on the remote control.

Pressing this button performs the following.

For a computer signal



The vertical position, the horizontal position and the horizontal phase will be automatically adjusted. And the horizontal size

will be automatically set to the default.

Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

For a video signal, s-video signal or component video signal



The video format best suited for the respective input signal will be selected automatically. This function is available only when AUTO is selected for

(

32)

VIDEO FORMAT item in INPUT menu



The vertical position and horizontal position will be automatically set to the default. For a component video signal, also the horizontal phase will be automatically set to the default.

● The automatic adjustment operation requires several seconds. Also please

note that it may not function correctly with some input. When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

●

The items adjusted by this function may vary when FINE or DISABLE is

selected for AUTO ADJUST item of SERVICE item in OPTION menu

AUTO

(

43)



Adjusting the position

Press POSITION button on the remote control when no menu

is indicated.

The “POSITION” indication will appear on the screen.

Use the ▲/▼/◄/► cursor buttons to adjust the picture position.

When you want to reset the operation, press RESET button on the remote control during the operation. To complete this operation, press POSITION button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● When this function is performed on a video signal, s-video signal or component video signal, some image such as an extra-line may appear at outside of the picture.

● When this function is performed on a video signal, s-video signal or component video signal, the range of this adjustment depends on OVER SCAN in IMAGE

(

29)

● If POSITION button is pressed when a menu is indicated on screen, the displayed picture does not move its position but the menu does.



setting. It is not possible to adjust when OVER SCAN is set to 10.

POSITION

Page 20

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

COMPUTER

Correcting the keystone distortions

Press KEYSTONE button on the remote control. A dialog will

appear on the screen to aid you in correcting the distortion. Use the ▲/▼ cursor buttons to select AUTO or MANUAL

operation, and press the ► button to perform the following.

(1) AUTO executes automatic vertical keystone correction.

(2) MANUAL displays a dialog for keystone correction.

Use the ▲/▼ buttons for adjustment.

To close the dialog and complete this operation, press KEYSTONE button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● The adjustable range of this correction will vary among inputs. For some input, this function may not work well.

● When V:INVERT or H&V:INVERT is selected for MIRROR item in SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly.

● When the zoom adjustment is set to TELE (telephoto focus), the automatic keystone distortion correction may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.

● When the projector is placed on the level (about ±0°), the automatic keystone distortion correction may not work.

● When the projector is inclined to near ±30 degree or over, this function may not work well.

● This function will be unavailable when Transition Detector is on (

KEYSTONE

49).



Using the magnify feature

Press the ON button of MAGNIFY on the remote control.

The “MAGNIFY” indication will appear on the screen and the projector will go into the MAGNIFY mode. The indication will disappear in several seconds with no operation.

Use the ▲/▼ cursor buttons to adjust the zoom level.

To move the zoom area, press POSITION button in the MAGNIFY mode, then use the ▲/▼/◄/► cursor buttons to move the area. And to nalize the zoom area, press POSITION button again.

To exit from the MAGNIFY mode and restore the screen to normal, press the OFF button of MAGNIFY on the remote control.

● The projector automatically exits from the MAGNIFY mode when the input signal is changed or when the display condition is changed.

● In the MAGNIFY mode, the keystone distortion condition may vary, it will be restored when the projector exits from the MAGNIFY mode.

NOTE • The zoom level can be nely adjusted. Closely watch the screen to

nd the level you want.

MAGNIFY

ON/OFF

Page 21

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

COMPUTER

Freezing the screen

Press FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen (however,

the indication will not appear when TURN OFF is selected for

(

39)

MESSAGE item in SCREEN menu



), and the projector will go into the FREEZE mode. To exit the FREEZE mode and restore the screen to normal, press FREEZE button again.

● The projector automatically exits from the FREEZE mode when one of the projector’s buttons or remote control buttons of STANDBY/ON, SEARCH, COMPUTER, VIDEO, BLANK, AUTO, VOLUME,

MUTE, KEYSTONE, MENU, MAGNIFY and MY BUTTON1/2(except

(

42)

MY MEMORY or PICTURE MODE is assigned to)



is pressed.

● If the projector continues projecting a still image for a long time, the LCD panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long.

FREEZE

Temporarily blanking the screen

Press BLANK button on the remote control.

The blank screen will be displayed instead of the screen of

input signal. Please refer to BLANK item in SCREEN menu

(

36).



To exit from the blank screen and return to the input signal screen, press BLANK button again.

● The projector automatically returns to the input signal screen when one of the projector’s buttons or the remote control buttons (except ASPECT, POSITION, MAGNIFY or FREEZE button, also except MY BUTTON1/2 if AUTO KEYSTONE EXECUTE or MY MEMORY or

(

42)

PICTURE MODE is assigned to



) is pressed.

BLANK

NOTE • The sound is not connected with the blank screen function.

If necessary, set the volume or mute rst.

Page 22

Operating

HOM

PAGE UP

PAGE DOWN

VIDE

FREEZ

MAGNIFY

ASPECT

AUT

BLANK

MUT

VOLUME

KEYS

MY BUTTO

POSITIO

1 2

ENTE

RESET

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

Using the menu function

This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, OPTION and EASY MENU.

EASY MENU consists of functions often used, and the other menus are classied into each purpose and brought together as Advanced Menu. Each of these menus is operated using the same methods. The basic operations of these menus are as follows.

MENU button

ENTER button MENU button

Cursor buttons

ESC button

Press the MENU button on the remote control or the projector.

The Advanced Menu or EASY MENU, which has priority just after powered

RESET button

on will appear.

If you want to move the menu position, use the cursor buttons after pressing the POSITION button. While the projector is displaying any menu, MENU button on the projector works as the cursor buttons.

In the EASY MENU

If you want to change it to the Advanced Menu,

select the “Go to Advanced Menu...” Use the ▲/▼ cursor buttons to select an item to

operate.

Use the ◄/► cursor buttons to operate the item.

(continued on next page)

EASY MENU

Page 23

Operating

Using the menu function (continued)

In the Advanced Menu

Use the ▲/▼ cursor buttons to select a menu.

If you want to change it to the EASY MENU, select

EASY MENU.

Then press the ► cursor button, or ENTER button to select an item. The lower layer menu of the selected item will appear.

Use the ▲/▼ cursor buttons to select an item to

operate.

Then press the ► cursor button, or ENTER button to progress. The operation menu of the selected item will appear.

Use the ▲/▼ cursor buttons to operate the item.

● Some functions cannot be performed when a certain input port is selected, or when a certain input signal is displayed.

● When you want to reset the operation, press RESET button on the remote control during the operation. Note that some items (ex. LANGUAGE, H PHASE, VOLUME) cannot be reset.

● In the Advanced Menu, when you want to return to the previous display, press the ◄ cursor button or ESC button on the remote control.

Press MENU button on the remote control again to close the menu and

complete this operation. Even if you do not do anything, the dialog will

automatically disappear after about 10 seconds.

Advanced Menu

Page 24

EASY MENU

From the EASY MENU, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table.

Item Description

ASPECT

AUTO

KEYSTONE

EXECUTE

KEYSTONE

Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu (



29).

Using the ► button executes the auto keystone function. See AUTO KEYSTONE EXECUTE item in SETUP menu (

Using the ◄/► buttons corrects the vertical keystone distortion.

See KEYSTONE

item in SETUP menu (

Using the ◄/► buttons switches the picture mode. The picture modes are combinations of GAMMA and COLOR

TEMP settings. Choose a suitable mode according to the projected source.

NORMAL ó CINEMA ó DYNAMIC ó BOARD(BLACK)



34).



34).

DAYTIME ó WHITEBOARD ó BOARD(GREEN)

NORMAL #2 MID DEFAULT #1 DEFAULT

PICTURE MODE

CINEMA #3 LOW DEFAULT #2 DEFAULT DYNAMIC #1 HIGH DEFAULT #3 DEFAULT BOARD(BLACK) #4 Hi-BRIGHT-1 DEFAULT #4 DEFAULT BOARD(GREEN) #5 Hi-BRIGHT-2 DEFAULT #4 DEFAULT WHITEBOARD #2 MID DEFAULT #5 DEFAULT DAYTIME #6 Hi-BRIGHT-3 DEFAULT #6 DEFAULT

• When the combination of GAMMA and COLOR TEMP differs

from pre-assigned modes above, the display on the menu for the PICTURE MODE is “CUSTOM”. Please refer to GAMMA ( COLOR TEMP (

• When this function is performed, a certain extra such as a line

may appear.

(continued on next page)

COLOR TEMP GAMMA

26) items in PICTURE menu.



26) and



Page 25

EASY MENU (continued)

Item Description

BRIGHTNESS

CONTRAST

COLOR

TINT

SHARPNESS

WHISPER

MIRROR

RESET

FILTER TIME

LANGUAGE

Go to

Advanced Menu...

Using the ◄/► buttons adjusts the brightness. See BRIGHTNESS item in PICTURE menu (

Using the ◄/► buttons adjusts the contrast. See CONTRAST item in PICTURE menu (

Using the ◄/► buttons adjusts the strength of whole color. See COLOR item in PICTURE menu (

Using the ◄/► buttons adjusts the tint. See TINT item in PICTURE menu (

Using the ◄/► buttons adjusts the sharpness. See SHARPNESS item in PICTURE menu (

Using the ◄/► buttons turns off/on the whisper mode. See WHISPER item in SETUP menu (

Using the ◄/► buttons switches the mode for mirror status. See MIRROR item in SETUP menu (

Performing this item resets all of EASY MENU items except FILTER TIME and LANGUAGE. A dialog is displayed for conrmation. Selecting RESET using the ▲ button performs resetting.

Performing this item resets the lter time which counts usage time of the air lter. A dialog is displayed for conrmation. Selecting RESET using the ▲ button performs resetting. See FILTER TIME item in OPTION menu (

Using the ◄/► buttons changes the display language. See LANGUAGE item in SCREEN menu (

Select “Go to Advanced Menu…” on the menu, and press the or ENTER button to use the menu of PICTURE, IMAGE, INPUT, SETUP, SCREEN or OPTION.



26).



35).



26).



35).

26).



36).



27).

41).

EASY MENU

26).

►

Page 26

PICTURE Menu

#1 DEFAULT  #1 CUSTOM  #2 DEFAULT  #2 CUSTOM



#3 DEFAULT



CUSTOM



#5 DEFAULT

 #5

CUSTOM

 #4

DEFAULT

 #4

CUSTOM



DEFAULT



CUSTOM



#2 MID CUSTOM



#3 LOW DEFAULT



#3 LOW CUSTOM



#1 HIGH DEFAULT  #1 HIGH CUSTOM  #2 MID DEFAULT



#6 Hi-BRIGHT-3 CUSTOM



#6 Hi-BRIGHT-3 DEFAULT



#5 Hi-BRIGHT-2 CUSTOM



#5 Hi-BRIGHT-2 DEFAULT



#4 Hi-BRIGHT-1 CUSTOM



#4 Hi-BRIGHT-1 DEFAULT

PICTURE Menu

From the PICTURE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the

► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

BRIGHTNESS

CONTRAST

GAMMA

Using the ▲/▼ buttons adjusts the brightness.

Light ó Dark

Using the ▲/▼ buttons adjusts the contrast.

Strong ó Weak

Using the ▲/▼ buttons switches the gamma mode.

To adjust the "CUSTOM" modes, see "To adjust CUSTOM function in GAMMA and COLOR TEMP" (



28).

Using the ▲/▼ buttons switches the color temperature mode.

COLOR TEMP

To adjust the "CUSTOM" modes, see "To adjust CUSTOM function in GAMMA and COLOR TEMP" (

Using the ▲/▼ buttons adjusts the strength of whole color.

COLOR

Strong ó Weak

• This item can be selected only for a video signal, s-video or

component video signal.

Using the ▲/▼ buttons adjusts the tint.

TINT

Greenish ó Reddish

• This item can be selected only for a video signal, s-video or

component video signal.

(continued on next page)

28).



Page 27

PICTURE Menu (continued)

Item Description

Using the ▲/▼ buttons adjusts the sharpness.

SHARPNESS

MY MEMORY

Strong ó Weak

• There may be some noise and/or the screen may icker for a

moment when an adjustment is made. This is not a malfunction.

This projector has 4 memories for adjustment data (for all the items of PICTURE menu). Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER button performs each function.

LOAD-1, LOAD-2, LOAD-3, LOAD-4

Performing a LOAD function loads the data from the memory linked in the number included in the function’s name, and adjusts the picture automatically depending on the data.

• The LOAD functions whose linked memory has no data are skipped.

• Remember that the current adjusted condition will be lost by loading data. If you want to keep the current adjustment, please save it before performing a LOAD function.

• There may be some noise and the screen may icker for a moment when loading data. This is not malfunction.

• You can perform the LOAD function using MY BUTTONs. Please see MY BUTTON item in OPTION menu (

SAVE-1, SAVE-2, SAVE-3, SAVE-4

Performing a SAVE function saves the current adjustment data into the memory linked in the number included in the function’s name.

• Remember that the current data being stored of a memory will be lost by saving a new data into the memory.

PICTURE Menu

LOAD-1 ó LOAD-2 ó LOAD-3 ó LOAD-4

SAVE-4 óSAVE-3 ó SAVE-2 ó SAVE-1

42).



Page 28

PICTURE Menu

PICTURE Menu (continued)

To adjust CUSTOM function in GAMMA and COLOR TEMP

Sel e ctin g a m ode wh o se na m e i n clud e s CUSTOM in GAMMA or COLOR TEMP item and then pressing th e ► b utton or ENTER button displays a dialog to aid you in adjusting the mode. Choose an item using the ◄/► buttons, and adjust the level using the ▲/▼ buttons.

• When this function is performed, lines or other

distortion may appear.

You can display a test pattern on the top of the screen for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.

No pattern  Gray scale of 9 steps



Ramp  Gray scale of 15 steps

• You can also adjust each function without displaying test patterns.

for adjusting GAMMA

You can change the brightness of particular tones. The eight equalizing bars correspond to eight tone levels of the test pattern (Gray scale of 9 steps) except the darkest in the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalizing adjustment bar “1”. The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar.

for adjusting COLOR TEMP

You can change the intensity of each of 3 colors (Red, Green, Blue). OFFSET adjustments change the color intensity on the whole tones of the test pattern. GAIN adjustments mainly affect color intensity on the brighter tones of the test pattern.



GAMMA COLOR TEMP

test pattern

Page 29

IMAGE Menu

From the IMAGE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ▲/▼ buttons switches the mode for aspect ratio. For a computer signal

ASPECT

OVER SCAN

V POSITION

H POSITION

NORMAL

For a video signal, s-video signal or component video signal

4:3 ó 16:9 ó 14:9

For no signal

4:3 (xed)

• This item can be selected only for a proper signal.

• NORMAL mode keeps the original aspect ratio setting.

Using the ▲/▼ buttons adjusts the over-scan ratio.

Large (It reduces picture) ó Small (It magnies picture)

•

This item can be selected only for a video, s-video and component video signal.

• When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case, please adjust small.

Using the ▲/▼ buttons adjusts the vertical position.

Up ó Down

•

Over-adjusting the vertical position may cause noise to appear on the

screen. If this occurs please reset the vertical position to the default setting.

Pressing RESET button when V POSITION is selected will reset V POSITION to the default setting.

•

When this function is performed on a video signal, s-video signal, or component video signal, the range of this adjustment depends on OVER SCAN

(



set to 10.

Using the ▲/▼ buttons adjusts the horizontal position.

Left ó Right

•

Over-adjusting the horizontal position may cause noise to appear on the

screen. If this occurs please reset the horizontal position to the default setting.

Pressing RESET button when H POSITION is selected will reset H POSITION to the default setting.

•

When this function is performed on a video signal, s-video signal, or component video signal, the range of this adjustment depends on OVER SCAN

(



set to 10.

4:3 ó 16:9

above)

setting. It is not possible to adjust when OVER SCAN is

above)

setting. It is not possible to adjust when OVER SCAN is

SMALL

IMAGE Menu

(continued on next page)

Page 30

IMAGE Menu

IMAGE Menu (continued)

Item Description

Using the ▲/▼ buttons adjusts the horizontal phase to eliminate icker.

H PHASE

H SIZE

AUTO ADJUST

EXECUTE

Right ó Left

• This item can be selected only for a computer signal or component video signal.

Using the ▲/▼ buttons adjusts the horizontal size.

Large ó Small

• This item can be selected only for a computer signal.

• When this adjustment is excessive, the picture may not be

displayed correctly. In such a case, please reset the adjustment by pressing the RESET button during this operation.

Executing this item performs the automatic adjustment feature.

For a computer signal

The vertical position, the horizontal position and the horizontal phase (

will be automatically set to the default.

Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

For a video signal, s-video signal or component video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to VIDEO FORMAT item in INPUT menu ( The vertical position and horizontal position will be automatically set to the the default.

For a component video signal, also the horizontal phase will be automatically set to the default.

• The automatic adjustment operation requires several seconds.

Also please note that it may not function correctly with some input. When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

•

The items adjusted by this function may vary when FINE or DISABLE is selected for AUTO ADJUST item of SERVICE item in OPTION menu

43) will be automatically adjusted. And the horizontal size



32).



(

43).



Page 31

INPUT Menu

From the INPUT menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ▲/▼ buttons switches the progress mode.

TV ó FILM ó TURN OFF

• This function is performed only for an interlaced signal of a video,

PROGRESSIVE

VIDEO NR

COLOR SPACE

COMPONENT

s-video or component video of 525i (480i) or 625i (576i) signal.

• When TV or FILM is selected, the screen image will be sharp.

FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select TURN OFF, even though the screen image may lose the sharpness.

Using the ▲/▼ buttons switches the noise reduction mode.

HIGH ó MID ó LOW

• This function performs only for a video, s-video or component

video of 525i(480i) or 625i(576i) signal.

• When this function is excessive, it may cause a certain

degradation of the picture.

Using the ▲/▼ buttons switches the mode for color space.

AUTO ó RGB ó SMPTE240 ó REC709 ó REC601

• This item can be selected only for a computer signal or component

video signal except SCART RGB signal.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well at some signals. In such a

case, it might be good to select a suitable mode except AUTO.

Using the ▲/▼ buttons switches the function of the COMPONENT (Y, Cb/Pb, Cr/Pr) port.

COMPONENT

When the SCART RGB is selected, COMPONENT (Y, Cb/Pb, Cr/ Pr) and VIDEO ports will function as a SCART RGB port. A SCART cable is required for a SCART RGB input to the projector. For your reference, see the TECHNICAL part.

SCART RGB

INPUT Menu

(continued on next page)

Page 32

INPUT Menu

INPUT Menu (continued)

Item Description

The video format for S-VIDEO port and VIDEO port can be set. (1) Use the ◄/► buttons to select the input port. (2) Using the ▲/▼ buttons switches the mode

for video format.

AUTO ó NTSC

VIDEO FORMAT

FRAME LOCK

COMPUTER IN

N-PAL ó M-PAL ó NTSC4.43

• This item is performed only for a video signal

from VIDEO port or S-VIDEO port.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well for some signals. If the

picture becomes unstable (e.g. an irregular picture, lack of color), please select the mode according to the input signal.

Using the ▲/▼ buttons turns the frame lock function on/off.

TURN ON ó TURN OFF

• This item can be performed only on a computer signal with a

vertical frequency of 50 to 60 Hz.

• When the TURN ON is selected, a moving pictures are displayed

more smoothly.

• This function may cause a certain degradation of the picture. In

such a case, please select TURN OFF.

The computer input signal type for COMPUTER IN1 and IN2 ports can be set. (1) Use the ◄/► buttons to select the input

port to be set.

COMPUTER (IN)1 ó COMPUTER (IN)2

(2) Use the ▲/▼ buttons to select the

computer input signal type.

SYNC ON G ON ó SYNC ON G OFF

Selecting SYNC ON G ON allows reception of sync on Green signal.

• When SYNC ON G ON is selected, the picture may be distorted with certain input signals. In such a case, remove the signal connector rst and select SYNC ON G OFF on the menu, and then reconnect the signal.

(continued on next page)

PAL

SECAM

Page 33

INPUT Menu (continued)

Item Description

The resolution for the COMPUTER IN1 and IN2 input signals can be set on this projector.

(1) In INPUT menu select RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUTION menu will be displayed.

(2) In the RESOLUTION menu, select the resolution you wish to display using the ▲/▼ buttons. Selecting AUTO will set a resolution appropriate to the input signal.

(3) STANDARD Pressing the ► or ENTER button when selecting a STANDARD resolution will automatically adjust the horizontal and vertical positions, clock phase and horizontal size and automatically select an aspect ratio.

(3) CUSTOM

(3)-1 To set a custom resolution use the

RESOLUTION

▲/▼ buttons to select the CUSTOM and the CUSTOM RESOLUTION box will be displayed. Set the horizontal (HORZ) and vertical (VERT) resolutions using the ▲ /▼/◄/► buttons. Although not all resolutions are guaranteed.

(3)-2 To save the setting place the

cursor on the right-most digit and press the ► button.

The horizontal and vertical positions,

clock phase and horizontal size will be automatically adjusted and an aspect ratio will be automatically selected.

(3)-3 To revert back to the previous

resolution without saving changes place the cursor on the left-most digit and press the ◄ button.

The screen will then return to the

RESOLUTION menu displaying the previous resolution.

• For some pictures, this function may not work well.

INPUT Menu

STANDARD

↓

CUSTOM

↓

Page 34

SETUP Menu

From the SETUP menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table.

Item Description

Selecting this item performs the automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself.

This function will be executed only once when selected in the menu. When the slant of the projector is changed, execute this function again.

• The adjustable range for correction will vary among inputs. For

some input, this function may not work well.

AUTO

KEYSTONE

EXECUTE

KEYSTONE

(continued on next page)

• When V:INVERT or H&V:INVERT is selected to the MIRROR item

in the SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly.

• When the zoom adjustment is set to the TELE (telephoto focus),

this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.

• When the projector is placed on the level (about ±0°), this function

may not work.

• When the projector is inclined to near ±30 degree or over, this

function may not work well.

• This function will be unavailable when the Transition Detector is

on (

49).



Using the ▲/▼ buttons corrects the vertical keystone distortion.

Shrink the top of the image ó Shrink the bottom of the image

• The adjustable range of this function will vary with the type of input

signal. For some input, this function may not work well.

• This function will be unavailable when the Transition Detector is

on (

49).



Page 35

SETUP Menu (continued)

Item Description

Using the ▲/▼ buttons turns off/on the whisper mode.

WHISPER

NORMAL ó WHISPER

• When WHISPER is selected, acoustic noise and screen brightness

are reduced.

Using the ▲/▼ buttons switches the mode for mirror status.

SETUP Menu

MIRROR

VOLUME

SPEAKER

AUDIO

NORMAL ó H:INVERT ó V:INVERT ó H&V:INVERT

If the Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm ( projector is restarted after the power switch is turned off.

Using the ▲/▼ buttons adjusts the volume.

High ó Low

Using the ▲/▼ buttons turns on/off the built-in speaker.

TURN ON ó TURN OFF

When TURN OFF is selected, the built-in speaker does not work.

Allocates the audio ports. (1) Choose a picture input port using the

▲/▼ buttons.

COMPUTER (IN)1

VIDEO

(2) Select the audio port to be interlocked

with the input port using the ◄/► buttons.

1 ó 2 ó 3 ó

When is selected to an input port, any audio ports do not work

interlocking with the input port, and any items in AUDIO menu are invalid.

S-VIDEO

COMPUTER (IN)2

COMPONENT

49) will be displayed when



Page 36

SCREEN Menu



TÜRKÇE



POLSKI



SUOMI



ENGLISH  FRANÇAIS  DEUTSCH  ESPAÑOL  ITALIANO



NORSK



NEDERLANDS



PORTUGUÊS



РУССКИЙ  SVENSKA  뼑鞵  㐕储Ё᭛  ㅔԧЁ᭛  ᣣᧄ⺆

SCREEN Menu

From the SCREEN menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ▲/▼ buttons switches the OSD (On Screen Display) language.

LANGUAGE

Using the ▲/▼/◄/► buttons adjusts the menu position.

MENU POSITION

BLANK

(continued on next page)

To quit the operation, press MENU button on the remote control or keep no operation for about 10 seconds.

Using the ▲/▼ buttons switches the mode for the blank screen. The blank screen is a screen for the temporarily blanking feature (

21). It is displayed by pressing BLANK button.



MyScreen ó ORIGINAL

BLUE

WHITE ó BLACK

Feature

MyScreen

ORIGINAL Screen preset as the standard screen.

BLUE, WHITE,

BLACK

Screen can be registered by the MyScreen item

(

38)



Plain screens in each color.

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL

screen will change to the plain black screen after several minutes.

Page 37

SCREEN Menu (continued)

Item Description

Using the ▲/▼ buttons switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected.

MyScreen ó ORIGINAL ó TURN OFF

MyScreen

START UP

ORIGINAL Screen preset as the standard screen.

TURN OFF Plain black screen.

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the BLANK screen ( minutes. If also the BLANK screen is the MyScreen or ORIGINAL, the plain black screen is instead used.

• When the TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION menu ( MyScreen.

(continued on next page)

SCREEN Menu

Feature Screen can be registered by the MyScreen item

(

38)



36) after several



46), the START UP is fixed to



Page 38

SCREEN Menu

SCREEN Menu (continued)

Item Description

This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.

1. Selecting this item displays a dialog

titled “MyScreen”. It will ask you if you start capturing an image from

the current screen. Please wait for the target image to be displayed, and press the ENTER button when the image is displayed. The image will freeze and the frame for capturing will appear. To stop performing, press the RESET or ESC button.

2. Using the ▲/▼/◄/► buttons adjusts

the frame position.

Please move the frame to the position

of the image which you want to use.

MyScreen

MyScreen Lock

The frame may not be able to be

moved for some input signals.

To start registration, press the ENTER

button.

To restore the screen and return to

the previous dialog, press the RESET

or ESC button.

Registration takes several minutes.

When the registration is completed, the registered screen and the following message are displayed for several seconds:

“MyScreen registration is nished.”

If the registration failed, the following message is displayed:

“A capturing error has occurred. Please try again.”

• This function cannot be selected when the TURN ON is selected to the MyScreen Lock item (

• This function cannot be selected when TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION menu (

46).



Using the ▲/▼ buttons turns on/off the MyScreen lock function.

TURN ON ó TURN OFF

When the TURN ON is selected, the MyScreen item is locked. Use this function for protecting the current MyScreen.

• This function cannot be selected when TURN ON is selected to

the MyScreen PASSWORD of SECURITY item in OPTION menu (

46).



below).

(continued on next page)

Page 39

SCREEN Menu (continued)

Item Description

Using the ▲/▼ buttons turns on/off the message function.

TURN ON ó TURN OFF

When the TURN ON is selected, the following message function works.

“AUTO IN PROGRESS” while automatically adjusting “NO INPUT IS DETECTED” “SYNC IS OUT OF RANGE” “Searching…” while searching for the input

MESSAGE

SOURCE NAME

“Detecting…” while an input signal is detected The indication of the input signal displayed by changing The indication of the aspect ratio displayed by changing The indication of the PICTURE MODE displayed by changing The indication of the MY MEMORY displayed by changing The indication of “FREEZE” and “II” while freezing the screen by pressing FREEZE button.

• When TURN OFF is selected, please remember if the picture is

freezing. Do not mistake freezing for a malfunction (

Each input port for this projector can have a name applied to it. (1) Use the

select SOURCE NAME and press the ► button. The SOURCE NAME menu will be displayed.

(2) Use the ▲/▼ buttons on the SOURCE NAME menu to select the port to be named and press the ► button. Right side of the menu is blank until a name is specied. The SOURCE NAME dialog will be displayed.

(3) The current name will be displayed on the rst line. Use the ENTER or INPUT button to select and enter characters. The RESET button can be used to erase 1 character at a time. The name can be a maximum of 16 characters.

(4) To change an already inserted character, press the ▲ button while the cursor is on the [A-N] row to move the cursor to the name displayed on the rst line and use the character to be changed. Once a character in the name is selected use the ▼ button to move the cursor back down to the character entry area to select and enter characters as described above.

(5) Select and press ENTER or INPUT buttons when nished entering text. To revert to the previous name without saving changes press the ESC or ◄ button and the INPUT button simultaneously.

▲/▼

buttons on the SCREEN menu to

▲/▼/◄/►

buttons and the

◄/►

buttons to select

SCREEN Menu

21).



Page 40

OPTION Menu

From the OPTION menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table.

Item Description

Using the ▲/▼ buttons turns on/off the automatic signal search function.

TURN ON ó TURN OFF

When the TURN ON is selected, detecting no signal automatically cycles through input ports in the following order. The search is

AUTO SEARCH

started from the current port. Then when an input is found, the

projector will stop searching and display the image.

COMPUTER IN1  COMPUTER IN2

Using the ▲/▼ buttons turns on/off the automatic keystone function.

TURN ON ó TURN OFF

TURN ON : Automatic keystone distortion correction will be executed whenever changing the slant of the projector.

AUTO

KEYSTONE

AUTO ON

TURN OFF : This function is disabled. Please execute the AUTO KEYSTONE EXECUTE in the SETUP Menu for automatic keystone distortion correction.

• When the projector is suspended from the ceiling this feature will not function properly so select the TURN OFF.

• This function will be unavailable when the Transition Detector is on (

Using the ▲/▼ buttons turns on/off the AUTO ON function.

TURN ON ó TURN OFF

When set to the TURN ON, the lamp in projector will be automatically turned on without the usual procedure ( when the projector is supplied with the power after the power was cut while the lamp was on.

• This function does not work as long as the power has been supplied to the projector while the lamp is off.

• After turning the lamp on by the AUTO ON function, if neither input nor operation is detected for about 30 minutes, the projector is turned off, even though the AUTO OFF function (

(continued on next page)

VIDEO

49).





S-VIDEO

COMPONENT



15), only



41) is disabled.



Page 41

OPTION Menu (continued)

Item Description

Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off.

Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE)

OPTION Menu

AUTO OFF

LAMP TIME

FILTER TIME

When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with nosignal or an unsuitable signal reaches at the set time, the projector lamp will be turned off. If one of the projector's buttons or the remote control buttons is pressed or one of the commands (except get commands) is transmitted to the CONTROL port during the corresponding time, projector will not be turned off. Please refer to the section “Turning off the power” (

The lamp time is the time counted after the last resetting. It is shown in OPTION menu as the usage time of the lamp. Pressing RESET button or the ► button displays a dialog.

To reset the lamp time, select RESET using the ▲ button.

RESET  CANCEL

• Please reset the lamp time only when you have replaced the lamp,

for a suitable indication about the lamp.

• For the lamp replacement, see the section "Lamp" (51).

The lter time is the time counted after the last resetting. It is shown in the OPTION menu as the usage time of the air lter. Pressing the RESET button or the ► button displays a dialog.

To reset the lter time, select the RESET using the ▲ button.

RESET  CANCEL

•

Please reset the lter time only when you have cleaned or replaced

the air lter, for a suitable indication about the air lter.

• For the air lter cleaning, see the section "Air lter" (53).

(continued on next page)



15).

Page 42

OPTION Menu

OPTION Menu (continued)

Item Description

This item is to assign one of the following functions to MY BUTTON 1 and 2 on the remote control ( Choose 1 or 2 on the MY BUTTON menu using the ◄/► button rst. Then using the ▲/▼ buttons sets one of the following functions to the chosen button.

• COMPUTER1: Sets port to COMPUTER IN1.

• COMPUTER2: Sets port to COMPUTER IN2.

• COMPONENT: Sets port to COMPONENT(Y, Cb/Pb, Cr/Pr)

• S-VIDEO: Sets port to S-VIDEO.

• VIDEO: Sets port to VIDEO.

•

INFORMATION: Displays a dialog of INPUT INFORMATION

• AUTO KEYSTONE EXECUTE: Performs automatic keystone distortion correction (

• MY MEMORY:

MY BUTTON

Loads one of adjustment data stored (

When the current adjustment is not saved to memory a dialog is displayed.

If you want to keep the current adjustment, please press the ◄ button to quit. Otherwise the current adjusted condition will be lost by loading a data.

• PICTURE MODE: Changes the PICTURE MODE (

• FILTER RESET: Displays the lter time reset conrmation dialogue (

• VOLUME+: Set the volume up.

• VOLUME-: Set the volume down.

Selecting this item displays the SERVICE menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button to execute the item.

FAN SPEED

AUTO ADJUST

GHOST



6).

34).



27).



When no data is saved in memory, a dialog is displayed.

24).



FILTER MESSAGE ó KEY LOCK

41).

(



44).

SERVICE

FAN SPEED

Using the ▲/▼ buttons switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc. Note that the projector is noisier when the HIGH is selected.

HIGH ó NORMAL

(continued on next page)

FACTORY RESET

I NFORMATION

REMOTE FREQ.

Page 43

OPTION Menu (continued)

Item Description

AUTO ADJUST

Using the ▲/▼ buttons enables/disables the automatic adjustment. When DISABLE is selected, the automatic adjustment feature is disabled, although rough adjustment is automatically performed depending on the basic setting.

FINE ó FAST ó DISABLE

FINE: Finer tuning including H.SIZE adjustment. FAST: Faster tuning, setting H.SIZE to prearranged data for the

• Depending on conditions, such as input image, signal cable to

the projector, environment around the projector, etc., the automatic adjustment may not work correctly. In such a case, please choose DISABLE to disable the automatic adjustment, and make adjustment manually.

GHOST

1. Select a color element of ghost using the ◄/► buttons.

SERVICE

(continued)

Adjust the selected element using the ▲/▼ buttons to disappear ghost.

FILTER MESSAGE

Use the ▲/▼ button to set the timer for the interval to show the message for cleaning up the air lter.

50h ó 100h ó 200h ó 300h ó 400h ó 500h TURN OFF ó 800h ó 700h ó 600h

After choosing a choice except “TURN OFF”, the message “REMINDER *** HRS PASSED AFTER THE LAST FILTER CHECK” will appear after the timer reaches the interval time set by this feature ( When the “TURN OFF” is chosen, the message will not appear. Utilize this feature to keep the air lter clean, setting the suitable time according to your environment of this projector.

• Please check and clean the air lter periodically, even if there is no

message. If the air lter becomes to be blocked by dust or others, the internal temperature will rise, which could cause malfunction, or reduce the lifetime of the projector.

• Please be careful with the operating environment of the projector

and the condition of the air lter.

(continued on next page)

input signal.

OPTION Menu

55).



Page 44

OPTION Menu

OPTION Menu (continued)

Item Description

KEY LOCK

Using the ▲/▼ buttons turns on/off the key lock feature. When TURN ON is selected, the buttons on the projector except the STANDBY/ON button are locked.

TURN ON ó TURN OFF

• Please use to avoid a mischief and touching accidentally. This

function does not have any effect on the remote control.

REMOTE FREQ.

Use the ▲/▼ button to change the projector's remote sensor setting.

1:NORMAL ó 2:HIGH

Items with a checkmark are on. The factory default setting is for both 1:NORMAL and 2: HIGH to be on. If the remote control does not function correctly set this to either only 1 or

SERVICE

(continued)

only 2 ( Neither can be turned off at the same time.

INFORMATION

Selecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.



14).

• The “FRAME LOCK” message on the dialog means the frame lock

function is working (32).

• This item can't be selected for no signal and sync out.

FACTORY RESET

Selecting RESET using the button ▲ performs this function. By this function, all the items in all of menus will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME, LANGUAGE and SECURITY are not reset.

RESET  CANCEL

(continued on next page)

Page 45

OPTION Menu (continued)

Item Description

This projector is equipped with security functions. User registration is required before using the security functions. Please contact your local dealer.

1. Using Security Features

1.1 Inputting the PASSWORD

1.1-1 Use the ▲/▼ buttons on the OPTION

menu to select SECURITY and press the ► button. The ENTER PASSWORD box

will be displayed. The factory default PASSWORD is 8471.

This PASSWORD can be changed (1.2 Changing the PASSWORD).

• It is strongly recommended the factory default PASSWORD to be changed as soon as possible.

1.1-2 Use the ▲/▼/◄/► buttons to enter

the registered PASSWORD. Move the cursor to the right side of the ENTER PASSWORD box and press the ► button to display the SECURITY menu.

If an incorrect PASSWORD is input the

ENTER PASSWORD box will be displayed again. If incorrect

SECURITY

PASSWORD is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PASSWORD is input.

OPTION Menu

1.2 Changing the PASSWORD

1.2-1 Use the ▲/▼ buttons on the SECURITY

1.2-2 Use the ▲/▼/◄/► buttons to enter the new PASSWORD.

1.2-3 Move the cursor to the right side of the

1.2-4 Move the cursor to the right side of the NEW

• Please do not forget your PASSWORD.

(continued on next page)

menu to select SECURITY PASSWORD CHANGE and press the ► button to display the ENTER NEW PASSWORD box.

ENTER NEW PASSWORD box and press the ► button to display the NEW PASSWORD AGAIN box, enter the same PASSWORD again.

PASSWORD AGAIN box and press the ► button and the NOTE NEW PASSWORD box will be displayed for about 20 seconds, please make note of the PASSWORD during this time. Pressing the ENTER button will close the NOTE NEW PASSWORD box.

Page 46

OPTION Menu

OPTION Menu (continued)

Item Description

1.3 If you have forgotten your PASSWORD

1.3-1 Follow the procedure in 1.1-1 to display the

ENTER PASSWORD box.

1.3-2 While the ENTER PASSWORD box is

displayed, press and hold the RESET button for about 3 seconds or press and hold the INPUT and ► buttons on the projector for about 3 seconds. The 10-digit Inquiring Code will be displayed.

• If there is no key input for about 55 seconds while the Inquiring Code is displayed the menu will close. If necessary repeat the process from 1.3-1.

1.3-3 Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD

will be sent after your user registration information is conrmed.

2. Using the MyScreen PASSWORD Function

The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.

SECURITY

(continued)

2.1 Turning on the MyScreen

2.1-1 Use the ▲/▼ buttons on the SECURITY

menu to select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/off menu.

PASSWORD

Function

2.2 Setting the PASSWORD

2.2-1 Display the MyScreen PASSWORD on/off menu using the procedure

2.2-2 Use the ▲/▼ buttons on the MyScreen

The ENTER PASSWORD box (small) will be displayed.

2.2-3 Use the ▲/▼/◄/► buttons to enter the

(continued on next page)

in 2.1-1.

PASSWORD on/off menu to select TURN ON.

PASSWORD.

Move the cursor to the right side of the ENTER PASSWORD box (small) and press the ► button to display the PASSWORD AGAIN box, enter the same PASSWORD again.

Page 47

OPTION Menu (continued)

Item Description

2.2-4 Move the cursor to the right side of the

PASSWORD AGAIN box and press the ► button to display the PASSWORD for about 20 seconds, please make note of the

PASSWORD during this time. Pressing the ENTER button will return to MyScreen PASS WORD on/off menu. When a PASSWORD is set for MyScreen:

The MyScreen registration function (and menu) will be unavailable.

•

The MyScreen Lock function (and menu) will be unavailable.

•

The START UP setting will be locked on MyScreen (and the menu will

•

be unavailable). Turning the MyScreen PASSWORD off will allow normal operation of both functions.

Please do not forget your MyScreen PASSWORD.

•

2.3 Turning the PASSWORD off

2.3-1 Follow the procedure in 2.1-1 to display the MyScreen PASSWORD

on/off menu.

2.3-2 Select TURN OFF to display the ENTER PASSWORD box (large). Enter the registered PASSWORD and the screen will return to the

SECURITY

(continued)

MyScreen on/off menu.

If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from 2.3-1.

2.4 If you have forgotten your PASSWORD

2.4-1 Follow the procedure in 2.1-1 to display the MyScreen PASSWORD on/off menu.

2.4-2 Select TURN OFF to display the ENTER

PASSWORD box (large). The 10-digit

Inquiring Code will be displayed inside the box.

2.4-3 Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD will be sent after your user registration information is conrmed.

3. Using the PIN LOCK Function

PIN LOCK is a function which prevents the projector from being used unless a registered Code is input.

3.1 Registering the PIN Code

3.1-1 Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.

(continued on next page)

OPTION Menu

Page 48

OPTION Menu

OPTION Menu (continued)

Item Description

3.1-2 Use the ▲/▼ buttons on the PIN LOCK on/off menu to select TURN ON and the PIN BOX will be displayed.

3.1-3 Input a 4 part PIN Code using the ▲, ▼, ◄, ►, COMPUTER and INPUT buttons.

A PIN Code again box will appear. Reenter the same PIN Code. This will complete the PIN Code registration.

If there is no key input for about 55 seconds while the PIN BOX or the

•

PIN Code again box are displayed the menu will close. If necessary repeat the process from 3.1-1. Afterwards, anytime the projector is restarted after AC power is turned off the PIN BOX will be displayed. Enter the registered PIN Code. The projector can be used after entering the registered PIN Code. If an incorrect PIN Code is input the PIN BOX will be displayed again. If an incorrect PIN Code is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PIN Code is input. The projector will also turn off if there is no key input for about 5 minutes while the PIN BOX is displayed.

SECURITY

(continued)

This function will activate only when the projector is started after AC power is turned off.

Please do not forget your PIN Code.

•

3.2 Turning Off the PIN LOCK Function

3.2-1 Follow the procedure in 3.1-1 to display the PIN LOCK on/off menu. Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be displayed.

Enter the registered PIN Code to turn the PIN LOCK function off. If an incorrect PASSWORD is entered the menu will close.

3.3 If you have forgotten your PIN Code

3.3-1 While the PIN BOX is displayed, press and

If it passes for about 5 minutes after the PIN BOX is displayed the

•

projector will turn off.

3.3-2 Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD

(continued on next page)

hold the RESET button for 3 seconds or press and hold the INPUT and ► buttons for 3 seconds. The 10-digit Inquiring Code will be displayed.

will be sent after your user registration information is conrmed.

Page 49

OPTION Menu (continued)

Item Description

4. Using the Transition Detector Function

While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below.

• Transition Detector alarm shown below might appear on screen, if the

projector has been moved or re-installed.

• Transition Detector alarm might appear on screen, if the MIRROR setting

has been changed.

• Keystone adjustment feature has been prohibited as long as the Transition

Detector function is ON.

4.1 Turning On the

4.1-1

Us e the ▲/▼ button s on the SECURIT Y menu to select TRANSITION DETECTOR and press the ► or the ENTER button to display

the TRANSITION DETECTOR on/off menu.

Select TURN ON and the current angle and mirror setting will be recorded.

• This feature may not function properly if the projector is not in a stable position when TURN ON is selected.

4.1-2 If this function is s et to TURN ON when the vertical angle of the projector or mirror setting at which the projector is turned on

SECURITY

(continued)

is different than the previously recorded the Transition Detector Alarm will be displayed and the projector will not display the input signal.

Set the Transition Detector off in the SECURITY menu to display the input signal. If the Transition Detector ALARM is displayed for about 5 minutes the lamp will turn off. This function will activate only when the projector is started after turning off the AC power.

4.2 Setting the

4.2-1 Use the ▲/▼ buttons on the SECURITY menu to select TRANSITION DETECTOR and press the ► or the ENTER button to display the TRANSITION DETECTOR on/off menu.

4.2-2 Use the ▲/▼ buttons on the TRANSITION DETECTOR on/off menu to select TURN ON. The ENTER PASSWORD box (small) will be displayed.

4.2-3 Use the ▲/▼/◄/► buttons to enter a PASSWORD. Move the cursor to the right side of the ENTER PASSWORD box (small) and press the ► button to display the PASSWORD AGAIN box, enter the same PASSWORD again.

(continued on next page)

Transition Detector

OPTION Menu

Function

PASSWORD

Page 50

OPTION Menu

OPTION Menu (continued)

Item Description

4.2-4 Move the cursor to the ri ght side of the PASSWO RD AGAI N box and pr ess th e ► button to display the PASSWORD for about 20 seconds, please make note of the PASSWORD during this time.

Pressing the ENTER button will return to the TRANSITION DETECTOR on/off menu.

• Please do not forget your Transition Detector PASSWORD.

4.3 Setting the Transition Detector off

4.3-1 Follow the procedure in 4.1-1 to display the TRANSITION DETECTOR on/off menu.

SECURITY

(continued)

4.3-2 Select TURN OFF to display the ENTER PASSWORD box (large). Enter the registered PASSWORD and the screen will return to the TRANSITION DETECTOR on/off menu. If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from 4.3-1.

4.4 If you have forgotten your PASSWORD

4.4-1 Follow the procedure in 4.1-1 to display the TRANSITION DETECTOR on/off menu.

4.4-2 Select TURN OFF to display the ENTER PAS SWORD box (l arge) . The 1 0- digit Inquiring Code will be displayed inside the box.

4.4-3 Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD will be sent after your user registration information is conrmed.

Page 51

Maintenance

Lamp

A lamp has nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different

lifetime, and some may burst or burn out soon after you start using them.

Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, contact your dealer and tell the lamp type number.

Type number : DT00841

Replacing the lamp

Turn the projector off, and unplug the power cord.

Allow the projector to cool for at least 45 minutes.

Prepare a new lamp.

If the projector is mounted on a ceiling, or if the lamp

has broken, also ask the dealer to replace the lamp.

In case of replacement by yourself, follow the following procedure.

Loosen the screw (marked by arrow) of the lamp cover

and then slide the lamp cover to the side to remove it.

Loosen the 2 screws (marked by arrow) of the

lamp, and slowly pick up the lamp by the handles.

Insert the new lamp, and retighten rmly the

2 screws of the lamp that are loosened in the

previous process to lock it in place.

Slide the lamp cover back in place and rmly

fasten the screw of the lamp cover.

Turn the projector on and reset the lamp time

using the LAMP TIME item in the OPTION menu. (1) Press the MENU button to display a menu. (2) Point at the “Go to Advanced Menu …” in the menu

using the ▼/▲ button, then press the ► button.

(3) Point at the “OPTION” in the left column of the menu

using the ▼/▲button, then press the ► button.

(4) Point at the “LAMP TIME” using the ▼/▲ button, then press the ► button. A

dialog will appear.

(5) Press the ▲ button to select “RESET” on the dialog. It performs resetting the

lamp time.

CAUTION ►Do not touch any inner space of the projector, while the lamp

is taken out.

Lamp cover

Handles

NOTE • Please reset the lamp time only when you have replaced the lamp,

for a suitable indication about the lamp.

Page 52

Maintenance

Lamp (continued)

Lamp warning

HIGH VOLTAGE

WARNING

►The projector uses a high-pressure mercury glass lamp. The

HIGH TEMPERATURE HIGH PRESSURE

lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to y into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

►About disposal of a lamp: This product contains a mercury lamp; do not put

it in a trash. Dispose of it in accordance with environmental laws.

• For lamp recycling, go to www.lamprecycle.org. (in the US)

• For product disposal, contact your local government agency

or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does),

unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

Disconnect

the plug from the

power

• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, turn the projector off and unplug the power

outlet

cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

• Use only the lamp of the specied type.

• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

•

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• Using the lamp for long periods of time could cause it dark, not to light up or to burst. When the pictures appear dark, or when the color tone is poor, please replace the lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

Page 53

Maintenance

Air lter

Please check and clean the air lter periodically. When the indicators or a message prompts you to clean the air lter, comply with it as soon as possible. Replace the air lter when it is damaged or too soiled. To prepare a new air lter, contact your dealer and tell the air lter type number.

Type number : MU04951

When you replace the lamp, please replace the air lter. An air lter of specied type will come together with a replacement lamp for this projector.

Cleaning the air lter

Turn the projector off, and unplug the power cord.

Allow the projector to sufciently cool down. Use a vacuum cleaner on and around the lter

cover. Pull the lter cover knobs while lifting it. The lter

unit which consists of the lter’ cover, air lter and

lter frame will come off.

Use a vacuum cleaner for the lter vent of the

projector and the lter frame side of the lter unit.

If the air lter is damaged or too soiled, replace it according to the following procedure number 5 to 7. Otherwise, please jump to the procedure number 8.

Pull the lter frame’ knob up while holding the lter

cover. The lter frame will come off and the air

lter will appear.

Replace the air lter with new one.

Put the lter frame back.

Put the lter unit back into the projector.

Turn the projector on and reset the lter time using

the FILTER TIME item in the EASY MENU. (1) Press the MENU button to display a menu. (2)

Point at the “FILTER TIME” using the ▼/▲ button, then press the ► button. A dialog will appear.

(3) Press the ▲ button to select “RESET” on the dialog. It performs resetting the lter time.

Filter cover

Filter cover knobs

Filter unit

Filter frame

Air lter

Filter cover

WARNING ►Before taking care of the air lter, make sure the power cable

is not plugged in, then allow the projector to cool sufciently. ►

Use only the air lter of the specied type. Do not use the projector without the air lter or the lter cover. It could result in a re or malfunction to the projector ►

Clean the air lter periodically. If the air lter becomes clogged by dust or the like, internal temperatures rise and could cause a re, a burn or malfunction to the projector.

NOTE • Please reset the lter time only when you have cleaned or

replaced the air lter, for a suitable indication about the air lter.

• The projector may display the message such as “CHECK THE AIR FLOW” or turn off the projector, to prevent the internal heat level rising.

Page 54

Maintenance

Other care

Inside of the projector

In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year.

Caring for the lens

If the lens is awed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of handling.

Turn the projector off, and unplug the power cord. Allow the projector to cool

sufciently. After making sure that the projector is cool adequately, lightly wipe the lens

with a commercially available lens-cleaning wipe. Do not touch the lens

directly with your hand.

Caring for the cabinet and remote control

Incorrect care could have adverse inuence such as discoloration, peeling paint, etc.

Turn the projector off, and unplug the power cord. Allow the projector to cool

sufciently. After making sure that the projector is cool adequately, lightly wipe with gauze

or a soft cloth.

If the projector is extremely dirty, dip soft cloth in water or a neutral cleaner diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.

WARNING ►Before caring, make sure the power cable is not plugged in,

and then allow the projector to cool sufciently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. ►Never try to care for the inside of the projector personally. Doing is so dangerous. ►Avoid wetting the projector or inserting liquids in the projector. It could result in a re, an electric shock, and/or malfunction to the projector.

• Do not put anything containing water, cleaners or chemicals near the projector.

• Do not use aerosols or sprays.

CAUTION ►Please take right care of the projector according to the

following. Incorrect care could cause not only an injury but adverse inuence such as discoloration, peeling paint, etc. ►Do not use cleaners or chemicals other than those specied in this manual. ►Do not polish or wipe with hard objects.

Page 55

Troubleshooting

NO INPUT IS DETECTED



SYNC IS OUT OF RANGE

 fH kHz fV Hz

Troubleshooting

If an abnormal operation should occur, stop using the projector immediately.

WARNING ►Never use the projector if abnormal operations such as

smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company.

Otherwise if a problem occurs with the projector, the following checks and

measures are recommended before requesting repair.

If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied.

Related messages

When some message appears, check and cope with it according to the following table. Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message Description

There is no input signal.

Please conrm the signal input connection, and the status of the signal source.

The horizontal or vertical frequency of the input signal

is not within the specied range.

Please conrm the specs for your projector or the signal source specs.

The internal temperature is rising.

Please turn the power off, and allow the projector to cool down at least 20 minutes. After having conrmed the

CHECK THE AIR FLOW

REMINDER

*** HRS PASSED AFTER THE

LAST FILTER CHECK.

FILTER MAINTENANCE IS ESSENTIAL

TO REMOVE WARNING MESSAGE,

RESET FILTER TIMER.

SEE MANUAL FURTHER INFO.

following items, please turn the power ON again.

• Is there blockage of the air passage aperture?

• Is the air lter dirty?

• Does the peripheral temperature exceed 35°C?

If the same indication is displayed after the remedy, please set FAN SPEED of the SERVICE item in the OPTION menu to HIGH.

A note of precaution when cleaning the air lter.

Please immediately turn the power off, and clean or change the air lter referring to the “Air Filter” section of this manual. After you have cleaned or changed the air lter, please be sure to reset the lter timer (



53).

Page 56

Troubleshooting

Regarding the indicator lamps

When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table.

POWER

indicator

Lighting

In Orange

Blinking

In Green

Lighting

In Green

Blinking

In Orange

Blinking

In Red

Blinking

In Red

Lighting

In Red

Blinking

In Red

Lighting

In Red

Blinking

In Red

Lighting

In Red

(continued on next page)

LAMP

indicator

Turned

off

Turned

off

Turned

off

Turned

off

(discretionary)

Lighting

In Red

Blinking

In Red

Turned

off

TEMP

indicator

Turned

off

Turned

off

Turned

off

Turned

off

(discretionary)

Turned

off

Turned

off

Blinking

In Red

Description

The projector is in a standby state.

Please refer to the section “Power on/off”.

The projector is warming up.

Please wait.

The projector is in an on state.

Ordinary operations may be performed.

The projector is cooling down.

Please wait.

The projector is cooling down. A certain error has been detected.

Please wait until POWER indicator nishes blinking, and then perform the proper measure using the item descriptions below.

The lamp does not light, and there is a possibility that interior portion has become heated.

Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufciently cooled down, please make conrmation of the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air lter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the remedy, please change the lamp referring to the section “Lamp”.

The lamp cover has not been properly xed.

Please turn the power off, and allow the projector to cool down at least 45 minutes. After the projector has sufciently cooled down, please make conrmation of the attachment state of the lamp cover. After performing any needed maintenance, turn the power on again. If the same indication is displayed after the remedy, please contact your dealer or service company.

The cooling fan is not operating.

Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufciently cooled down, please make conrmation that no foreign matter has become caught in the fan, etc., and then turn the power on again. If the same indication is displayed after the remedy, please contact your dealer or service company.

Page 57

Regarding the indicator lamps (continued)

NOTE •

When the interior portion has become overheated, for safety purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufciently cooled down, please make conrmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

Shutting the projector down

Only when the projector can not be turned off by usual procedure

(



15)

, please push the shutdown switch using a pin or similar, and disconnect the power plug from the power outlet. Before turning it on again, wait at least 10 minutes to make the projector cool down enough.

Resetting all settings

When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu

(



44)

can reset all settings(except LANGUAGE,

FILTER TIME, LAMP TIME, FILTER MESSAGE and etc.) to the factory default.

Shutdown switch

Troubleshooting

POWER

indicator

Blinking

In Red

Lighting

In Red

Lighting

In Green

Lighting

In Green

LAMP

indicator

Turned

off

Simultaneous

blinking in Red

Alternative

blinking in Red

TEMP

indicator

Lighting

In Red

Description

There is a possibility that the interior portion has become heated.

• Is there blockage of the air passage aperture?

• Is the air lter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the remedy, please set FAN SPEED of SERVICE item in OPTION menu to HIGH

(

42)



It is time to clean the air lter.

Please immediately turn the power off, and clean or change the air lter referring to the section “Air Filter”. After cleaning or changing the air lter, please be sure to reset the lter timer. After the remedy, reset the power to ON.

There is a possibility that the interior portion has become overcooled.

Please use the unit within the usage temperature

parameters (5°C to 35°C).

After the treatment, reset the power to ON.

Page 58

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects

About the phenomenon confused with a machine defect, check and cope with it according to the following table.

Phenomenon Cases not involving a machine defect

The electrical power cord is not plugged in.

Correctly connect the power cord.

The main power source has been interrupted during operation such as by a power outage (blackout), etc.

Please disconnect the power plug from the power outlet,

Power does not

come on.

and allow the projector to cool down at least 10 minutes, then turn the power on again.

Either there is no lamp and/or lamp cover, or either

of these has not been properly xed.

Please turn the power off and disconnect the power plug from the power outlet, and allow the projector to cool down at least 45 minutes. After the projector has sufciently cooled down, please make conrmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

The signal cables are not correctly connected.

Correctly connect the connection cables.

Neither sounds

nor pictures are

outputted.

Signal source does not correctly work.

Correctly set up the signal source device by referring to the manual of the source device.

The input changeover settings are mismatched.

Select the input signal, and correct the settings.

The signal cables are not correctly connected.

Correctly connect the audio cables.

The MUTE function is working.

Restore the sound pressing MUTE or VOLUME button on

Sound does not

come out.

the remote control.

The volume is adjusted to an extremely low level.

Adjust the volume to a higher level using the menu function or the remote control.

The AUDIO/SPEAKER setting is not correct.

Correctly set the AUDIO/SPEAKER in SETUP menu.

The lens cover is attached.

No pictures are

displayed.

Remove the lens cover.

The signal cables are not correctly connected.

Correctly connect the connection cables.

Reference

page

12, 15

51, 52

–

16, 17

4, 15

(continued on next page)

Page 59

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon Cases not involving a machine defect

The brightness is adjusted to an extremely low level.

Adjust BRIGHTNESS to a higher level using the menu function.

No pictures are

displayed.

(continued)

The computer cannot detect the projector as a plug and play monitor.

Make sure that the computer can detect a plug and play monitor using another plug and play monitor.

The BLANK screen is displayed.

Press BLANK button on the remote control.

Video screen

display freezes.

The FREEZE function is working.

Press FREEZE button to restore the screen to normal.

Color settings are not correctly adjusted.

Colors have a

faded- out

appearance, or

Color tone is

poor.

Perform picture adjustments by changing the COLOR TEMP, COLOR, TINT and/or COLOR SPACE settings, using the menu functions.

COLOR SPACE setting is not suitable.

Change the COLOR SPACE setting to AUTO, RGB, SMPTE240, REC709 or REC601.

The brightness and/or contrast are adjusted to an

extremely low level.

Adjust BRIGHTNESS and/or CONTRAST settings to a higher level using the menu function.

Pictures appear

dark.

The WHISPER function is working.

Select NORMAL for WHISPER item in the SETUP menu.

The lamp is approaching the end of its product lifetime.

Replace the lamp.

Either the focus and/or horizontal phase settings are not properly adjusted.

Pictures appear

blurry.

Adjust the focus using the focus ring, and/or H PHASE using the menu function.

The lens is dirty or misty.

Clean the lens referring to the section “Caring for the lens”.

Reference

page

25, 26

25, 26,

25, 26

25, 35

51, 52

18, 30

NOTE • Although bright spots or dark spots may appear on the screen, this

is a unique characteristic of liquid crystal displays, and it does not constitute or imply a machine defect.

Page 60

Specications

Specications

Specication

Item Specication

Product name Liquid crystal projector

Liquid Crystal Panel

Lens

Lamp 220W UHB

Audio output 7 W

Power supply AC 100-120V/3.5A, AC220-240V/1.5A Power consumption 320W

Temperature range 5 ~ 35°C (Operating)

Size

Weight (mass) approx. 3.5 kg

Ports

Optional parts

Panel size 1.6 cm (0.63 type) Drive system TFT active matrix Pixels 786,432 pixels (1024 horizontal x 768 vertical)

Zoom lens,

<CP-X200>

F=1.7 ~ 1.9

f = 18.9~ 22.6 mm

340 (W) x 100 (H) x 270 (D) mm * Not including protruding parts. Please refer to the following gure.

Computer input port

COMPUTER IN1 ................................D-sub 15 pin mini x1

COMPUTER IN2 ................................D-sub 15 pin mini x1

Computer output port

MONITOR OUT ...................................D-sub 15 pin mini x1

Video input port

Y, Cb/Pb, Cr/Pr (Component video) ........................ RCA x3

S-VIDEO ................................................... mini DIN 4 pin x1

VIDEO ..................................................................... RCA x1

Audio input/output port

AUDIO IN1 .....................................................Stereo mini x1

AUDIO IN2 .....................................................Stereo mini x1

AUDIO IN3 ............................................................... RCA x2

AUDIO OUT ...................................................Stereo mini x1

Others

USB ......................................................................USB-B x1

CONTROL .................................................... D-sub 9 pin x1

Lamp: DT00841 Air lter: MU04951

* For more information, please consult your dealer.

<CP-X300>

F=1.7 ~ 1.9

f = 19.5~ 23.4 mm

<CP-X400>

F=1.6 ~ 1.8

f = 18.9~ 22.6 mm

(approximately)

Page 61









Specications (continued)

Specications

[unit: mm]