Hitachi CP-WX8 Operating Guide

Download

Page 1

Projector

CPWX8

User's Manual (detailed) Operating Guide

Thank you for purchasing this projector.

WARNING

product. Be sure to read “Safety Guide” rst. After reading them, store them in a safe place for future reference.

►Before using this product, please read all manuals for this

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING

CAUTION

NOTICE This entry notices of fear of causing trouble.

NOTE

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgment

• Mac

• Microsoft®, Internet Explorer®, Windows® and Windows Vista® are registered trademarks of Microsoft Corporation in the U.S. and/or other countries.

• VESA and DDC are trademarks of the Video Electronics Standard Association.

• HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

• Blu-ray Disc

All other trademarks are the properties of their respective owners.

• The information in this manual is subject to change without notice.

is a registered trademark of Apple Inc.

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



and Blu-rayTM are trademarks of Blu-ray Disc Association.

Page 2

Read this Safety Guide first.

Projector

User's Manual - Safety Guide

Thank you for purchasing this projector.

WARNING •

correct usage through understanding. After reading, store them in a safe place for future reference. Incorrect handling of this product could possibly result in personal injury or physical damage. The manufacturer assumes no responsibility for any damage caused by mishandling that is beyond normal usage defined in these manuals of this projector.

Before using, read these user's manuals of this projector to ensure

NOTE

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transmission or use of this document or contents is not permitted without express written authority.

• The information in this manual is subject to change without notice.

About The Symbols

Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the user and others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the contents.

This symbol indicates information that, if ignored, could

WARNING

CAUTION

Typical Symbols

This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.

possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due to incorrect handling.

This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left indicates that disassembly is prohibited).

This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left indicates that the power plug should be disconnected from the power outlet).

Page 3

Safety Precautions

WARNING

Never use the projector if a problem should occur.

Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock. In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be dangerous.

• The power outlet should be close to the projector and easily accessible.

Use special caution for children and pets.

Incorrect handling could result in fire, electrical shock, injury, burn or vision problem. Use special caution in households where children and pets are present.

Do not insert liquids or foreign object.

Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children are present. If liquids or foreign object should enter the projector, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer.

• Do not place the projector near water (ex. a bathroom, a beach, etc.).

• Do not expose the projector to rain or moisture. Do not place the projector outdoors.

• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the projector.

• Do not place metals, combustibles, etc on or around the projector.

• To avoid penetration of foreign objects, do not put the projector into a case or bag together with any thing except the accessories of the projector, signal cables and connectors.

Never disassemble and modify.

The projector contains high voltage components. Modification and/or disassembly of the projector or accessories could result in fire or electrical shock.

• Never open the cabinet.

• Ask your dealer to repair and clean insider.

Do not give the projector any shock or impact.

If the projector should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock. If the projector is shocked, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer.

Do not place the projector on an unstable surface.

If the projector should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.

• Do not place the projector on an unstable, slant or vibrant surface such as

a wobbly or inclined stand.

• Use the caster brakes placing the projector on a stand with casters.

• Do not place the projector in the side up position, the lens up position or

the lens down position.

• In the case of a ceiling installation or the like, contact your dealer before

installation.

Disconnect the

plug from the power outlet.

Do not

disassemble.

Page 4

Safety Precautions (continued)

WARNING

Be cautious of High temperatures of the projector.

High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present. Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn. Take care of ventilation.

• Keep a space of 30 cm or more between the sides and other objects such

as walls.

• Do not place the projector on a metallic table or anything weak in heat.

• Do not place anything about the lens, air fans and ventilation openings of

the projector.

• Never block the air fan and ventilation openings.

• Do not cover the projector with a tablecloth, etc.

• Do not place the projector on a carpet or bedding.

Never look through the lens or openings when the lamp is on.

The powerful light could adversely affect vision. Use special caution in households where children are present.

Use only the correct power cord and the correct power outlet.

Incorrect power supply could result in fire or electrical shock.

• Use only the correct power outlet depending on the indication on the

projector and the safety standard.

• The enclosed power cord must be used depending on the power outlet to

be used.

Be cautious of the power cord connection.

Incorrect connection of the power cord could result in fire or electrical shock.

• Do not touch the power cord with a wet hand.

• Check that the connecting portion of the power cord is clean (with no dust),

before using. Use a soft and dry cloth to clean the power plug.

• Insert the power plug into a power outlet firmly. Avoid using a loose,

unsound outlet or contact failure.

Be sure to connect with ground wire.

Connect the ground terminal of AC inlet of this unit with the ground terminal provided at the building using the correct power cord; otherwise, fire or electric shock can result.

• Don’t take the core of power cord away.

Surely connect

the ground wire.

Page 5

Safety Precautions (continued)

WARNING

Be careful in handling the light source lamp.

The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”. Be careful in handling the power cord and external connection

cables.

If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension to the power cord and cables. If the power cord or cables is damaged (exposed or broken core wires, etc.), contact your dealer.

• Do not place the projector or heavy objects on the power cord and cables.

Also, do not place a spread, cover, etc, over them because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.

• Do not pull the power cord and cables. When connecting and

disconnecting the power cord or cables, do it with your hand holding the plug or connector.

• Do not place the cord near the heater.

• Avoid bending the power cord sharply.

• Do not attempt to work on the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.

• Keep the battery away from children and pets. If swallowed consult a

physician immediately for emergency treatment.

• Do not allow the battery in a fire or water.

• Avoid fire or high-temperature environment.

• Do not hold the battery with the metallic tweezers.

• Keep the battery in a dark, cool and dry play.

• Do not short circuit the battery.

• Do not recharge, disassemble or solder the battery.

• Do not give the battery a physical impact.

• Use only the battery specified in the other manual of this projector.

• Make sure the plus and minus terminals are correctly aligned when loading

the battery.

• If you observe a leakage of the battery, wipe out the flower and then

replace the battery. If the flower adheres your body or clothes, rinse well with water.

• Obey the local laws on disposing the battery.

Page 6

Safety Precautions (continued)

CAUTION

Be careful in moving the projector.

Neglect could result in an injury or damage.

• Do not move the projector during use. Before moving, disconnect the

power cord and all external connections, and close the slide lens door or attach the lens cap.

• Avoid any impact or shock to the projector.

• Do not drag the projector.

• For moving the projector, use the enclosed case or bag if provided.

Do not put anything on top of the projector.

Placing anything on the projector could result in loss of balance or falling, and cause an injury or damage. Use special caution in households where children are present.

Do not attach anything other than specified things to the projector.

Neglect could result in an injury or damage.

• Some projector has a screw thread in a lens part. Do not attach anything

other than specified options (such as conversion lens) to the screw thread.

Avoid a smoky, humid or dusty place.

Placing the projector in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.

• Do not place the projector near a smoky, humid or dusty place (ex.

a smoking space, a kitchen, a beach, etc.). Do not place the projector outdoors.

• Do not use a humidifier near the projector.

Take care of the air filter to normal ventilate.

The air filter should be cleaned periodically. If the air filter becomes clogged by dust or the like, internal temperature rises and could cause malfunction. The projector may display the message such as “CHECK THE AIR FLOW” or turn off the projector, to prevent the internal heat level rising.

• When the indicators or a message prompts you to clean the air filter, clean

the air filter as soon as possible.

• If the soiling will not come off the air filter, or it becomes damaged, replace

the air filter.

• Use the air filter of the specified type only. Please order the air filter

specified in the other manual of this projector to your dealer.

• When you replace the lamp, replace also the air filter. The air filter may be

attached when you buy a replacement lamp for this projector.

• Do not turn on the projector without air filter.

Avoid a high temperature environment.

The heat could have adverse influence on the cabinet of the projector and other parts. Do not place the projector, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.

Avoid Magnetism.

Manufacture strongly recommends to avoid any magnetic contact that is not shielded or protected on or near the projector itself. (ie.,. Magnetic Security Devices, or other projector accessory that contains magnetic material that has not been provided by the manufacture etc.) Magnetic objects may cause interruption of the projector's internal mechanical performance which may interfere with cooling fans speed or stopping, and may cause the projector to completely shut down

Page 7

Safety Precautions (continued)

CAUTION

Remove the power cord for complete separation.

• For safety purposes, disconnect the power cord if the projector is not to be

used for prolonged periods of time.

• Before cleaning, turn off and unplug the projector. Neglect could result in

fire or electrical shock.

Ask your dealer to cleaning inside of the projector about every year.

Accumulations of dust inside the projector cause result in fire or malfunction. Cleaning inside is more effective if performed before every humid periods such as rainy season.

• Do not clean inside yourself because it is dangerous.

NOTE

Do not give the remote control any physical impact.

A physical impact could cause damage or malfunction of the remote control.

• Take care not to drop the remote control.

• Do not place the projector or heavy objects on the remote control.

Take care of the lens.

• Close the slide lens door or attach the lens cap to prevent the lens surface being

scratched when the projector is not used.

• Do not touch the lens to prevent fog or dirt of the lens that cause deterioration of display

quality.

• Use commercially available lens tissue to clean the lens (used to clean cameras,

eyeglasses, etc.). Be careful not to scratch the lens with hard objects.

Take care of the cabinet and the remote control.

Incorrect care could have adverse influence such as discoloration, peeling paint, etc.

• Use a soft cloth to clean the cabinet and control panel of the projector and the remote

control. When excessively soiled dilute a neutral detergent in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth. Do not use undiluted detergent directly.

• Do not use an aerosol sprays, solvents, volatile substances or abrasive cleaner.

• Before using chemical wipes, be sure to read and observe the instructions.

• Do not allow long-term close contact with rubber or vinyl.

About bright spots or dark spots.

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.

Be careful of printing of the LCD panel.

If the projector continues projecting a still image, inactive images or 16:9 aspect images in case of 4:3 panel, etc., for long time, the LCD panel might possibly be printed.

Disconnect the

plug from the power outlet.

Page 8

Safety Precautions (continued)

NOTE

About consumables.

Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans have a different lifetime in each. These parts may need to be replaced after a long usage time.

• This product isn’t designed for continuous use of long time. In the case of continuous use

for 6 hours or more, or use for 6 hours or more every day (even if it isn’t continuous), or repetitious use, the lifetime may be shortened, and these parts may need to be replaced even if one year has not passed since the beginning of using.

• Any inclining use beyond the adjustment range explained in these user’s manuals may shorten the lifetimes of the consumables.

Before turning on the power, make the projector cool down adequately.

After turning the projector off, pushing the restart switch or interrupting of the power supply, make the projector cool down adequately. Operation in a high temperature state of the projector causes a damage of the electrode and un-lighting of the lamp.

Avoid strong rays.

Any strong ray (such as direct rays of the sun or room lighting) onto the remote control sensors could invalidate the remote control.

Avoid radio interference.

Any interfering radiation could cause disordered image or noises.

• Avoid radio generator such as a mobile telephone, transceiver, etc. around the projector.

About displaying characteristic.

The display condition of the projector (such as color, contrast, etc.) depends on characteristic of the screen, because the projector uses a liquid crystal display panel. The display condition can differ from the display of CRT.

• Do not use a polarized screen. It can cause red image.

Turn the power on/off in right order.

To prevent any trouble, turn on/off the projector in right order mentioned below unless specifying.

• Power on the projector before the computer or video tape recorder.

• Power off the projector after the computer or video tape recorder.

Take care not to fatigue your eyes.

Rest the eyes periodically.

Set the sound volume at a suitable level to avoid bothering other people.

• It is better to keep the volume level low and close the windows at night to protect the

neighborhood environment.

Connecting with notebook computer

When connecting with notebook computer, set to valid the RGB external image output (setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of the notebook for more information.

Page 9

Lamp

WARNING

The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws. For lamp recycling, go to www.lamprecycle.org. (in USA) For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

Disconnect

the plug from

the power

outlet

• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

• Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

• Use the lamp of the specified type only.

• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• Using the lamp for long periods of time, could cause it dark, not to light up or to burst. When the pictures appear dark, or when the color tone is poor, please replace the lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

Page 10

Regulatory Notices

FCC Statement Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC

(Federal Communication Commission) equipment provided that the following conditions are met. Some cables have to be used with the core set. Use the accessory cable or a designated-type cable for the connection. For cables that have a core only at one end, connect the core to the projector.

CAUTION: Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

For the Customers in CANADA NOTICE: This Class B digital apparatus complies with Canadian ICES-003.

Warranty And After-Service

Unless seen any abnormal operations (mentioned with the first paragraph of WARNING in this manual), when a problem occurs with the equipment, first refer to the “Troubleshooting” section of the “Operating Guide”, and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied.

Page 11

Contents



Introduction . ..............3

Features Checking the contents of package

Part names . ...............4

Projector . .....................4

Control panel ...................5

Rear panel . ...................5

Remote control .................6

Setting up . ................7

Arrangement ...................7

Connecting your devices ..........9

Connecting power supply . ....... 11

Using the security bar and slot . . . . 11

Remote control ............12

Installing the batteries ...........12

About the remote control signal . . . 12

Power on/off . .............13

Turning on the power . ..........13

Turning off the power . ..........13

Operating . ...............15

Adjusting the volume ............15

Temporarily muting the sound .....15

Selecting an input signal .........15

Searching an input signal . .......17

Selecting an aspect ratio .........17

Adjusting the projector's elevator . . 18

Adjusting the zoom and focus .....18

Using the automatic adjustment feature

Adjusting the position . ..........19

Correcting the keystone distortions

Using the magnify feature ........21

Temporarily freezing the screen . . . 22 Temporarily blanking the screen . . 22

Using the menu function . .......23

EASY MENU...............25

ASPECT, AUTO KEYSTONE,KEYSTONE, PICTURE MODE, F

ILTER TIME,LANGUAGE,ADVANCED MENU,

XIT

......................3

... 3

... 19

.. 20

ECO MODE,MIRROR,RESET,



PICTURE menu . ...........27

BRIGHTNESS,CONTRAST,GAMMA, C

OLOR TEMP,COLOR,TINT,SHARPNESS,

Y MEMORY

IMAGE menu . .............30

ASPECT,OVER SCAN,VPOSITION,HPOSITION, H

PHASE,HSIZE, AUTO ADJUST EXECUTE

INPUT menu . .............33

PROGRESSIVE,VIDEO NR,COLOR SPACE, V

IDEO FORMAT,HDMI FORMAT,HDMI RANGE,

OMPUTER IN,FRAME LOCK,RESOLUTION

SETUP menu ..............37

AUTO KEYSTONE,KEYSTONE, AUTO ECO MODE

CO MODE,MIRROR,STANDBY MODE,

E M

ONITOR OUT

AUDIO menu . .............39

VOLUME,SPEAKER, AUDIO SOURCE,

DMI AUDIO

SCREEN menu.............40

LANGUAGE,MENU POSITION, BLANK, S

TAR T UP,

ESSAGE,SOURCE NAME,TEMPLATE,C.C.

yScreen

, M

yScreen Lock

OPTION menu . ............46

AUTO SEARCH, AUTO KEYSTONE, D

IRECT POWER ON, AUTO POWER OFF,

AMP TIME, FILTER TIME,MY BUTTON,

Y SOURCE,SERVICE

SECURITY menu ...........51

SECURITY PASSWORD CHANGE,

T M

PASSWORD,PIN LOCK,

yScreen

RANSITION DETECTOR,MY TEXT PASSWORD,

Y TEXT DISPLAY,MY TEXT WRITING

Maintenance ..............57

Replacing the lamp .............57

Cleaning and replacing the air lter . . 59

Other care ....................61

Troubleshooting . ..........62

Related messages . ............62

Regarding the indicator lamps . . . . 63

Resetting all settings ............64

Phenomena that may be easy

to be mistaken for machine defects

.. 65

Speciﬁcations .............69

Page 12

Introduction

Features

The projector provides you with the broad use by the following features.

9 This projector has a variety of I/O ports that supposedly cover for any

business scene. The HDMI port can support various image equipment which have digital interface to get clearer pictures on a screen.

9 This projector realizes the large projection image, even if in a small space. 9 The new double layer lter system is expected to function longer and offers

you less maintenance frequency.

9 This compact, lightweight projector uses a front exhaust system that keeps

the user comfortable by directing hot air away from the user.

Checking the contents of package

Please see the Contents of package section in the User’s Manual (concise) which is a book. Require of your dealer immediately if any items are missing.

NOTE

to use the original packing materials when moving the projector. Use special caution for the lens.

• Keep the original packing materials, for future reshipment. Be sure

Page 13

Part names

Projector

(1) Lamp cover (57)

The lamp unit is inside.

(2) Focus ring (18) (3) Zoom ring (18) (4) Control panel (5) (5) Elevator buttons (x 2) (18) (6) Elevator feet (x 2) (18) (7) Remote sensor (12) (8) Lens (61) (9) Intake vents (10) Filter cover (59)

The air lter and intake vent are inside.

(11) Speaker (39) (12) Exhaust vent (13) AC IN (AC inlet) (11) (14) Rear panel (5) (15) Security bar (11) (16) Security slot (11)

(6)

HOT!

(13)

HOT!

(12)

(1)

(2) (3) (4)

(16)

(8)

(14)

(7)

(11)

(9)

(15)

(10) (5)

(6)

(5)

(9)

WARNING

►HOT! : Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot. ►Do not look into the lens or vents while the lamp is on, since the strong light is not good for your eyes. ►Do not handle the elevator buttons without holding the projector, since the projector may drop down. ►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it.

CAUTION

►Maintain normal ventilation to prevent the projector from heating up. Do not cover, block or plug up the vents. Do not place anything that can stick or be sucked to the vents, around the intake vents. Clean the air lter periodically.

Page 14

Control panel

(1) STANDBY/ON button (13) (2) INPUT button (15, 23) (3) MENU button (23)

It consists of four cursor buttons. (4) BLANK button (22) (5) POWER indicator (11, 13, 63) (6) TEMP indicator (63) (7) LAMP indicator (63)

Rear panel (9)

%/$1.

0<%87721

(4)

(1) (3)(2)

Part names

(7)(6)

(5)

(1) VIDEO port (2) S-VIDEO port (3) AUDIO IN1 port (4) AUDIO IN2 port (5) AUDIO OUT port

(6) COMPUTER IN port (7) HDMI port (8) CONTROL port (9) MONITOR OUT port

(2) (3) (6) (7)

(8)(9) (4)(5)(1)

Page 15

Part names

Remote control

(1) VIDEO button (16) (2) COMPUTER button (16) (3) SEARCH button (17) (4) STANDBY/ON button (13) (5) ASPECT button (17) (6) AUTO button (19) (7) BLANK button (22) (8) MAGNIFY - ON button (21) (9) MAGNIFY - OFF button (21) (10) MY SOURCE/DOC.CAMERA button (16, 48) (11) VOLUME - button (15) (12) PAGE UP button * (13) PAGE DOWN button * (14) VOLUME + button (15) (15) MUTE button (15) (16) FREEZE button (22) (17) MY BUTTON - 1 button (48) (18) MY BUTTON - 2 button (48) (19) KEYSTONE button (20) (20) POSITION button (19, 24) (21) MENU button (23) (22) ▲/▼/◄/► cursor buttons (23) (23) ENTER button (23) (24) ESC button (23) (25) RESET button (23) (26) Battery cover (12)

(2) (1) (6) (5) (16) (8) (9) (19) (17) (20) (22)

(24)

COMPUTER

VIDEO

AUTO

ASPECT SEARCH

FREEZE

MAGNIFY

OFF

KEYSTONE

MY BUTTON

POSITION

ENTER

ESC

MY SOURCE/ DOC.CAMERA

PAGE UP

DOWN

BLANK

VOLUME

MUTE

(10) (4) (3) (7) (12)

㧗

(14)

࡯

(11) (13) (15) (18) (21)

RESET

(23) (25)

(26)

Back of

the remote control

• Any button marked with “*” is not supported on this projector (62).NOTE

Page 16

Setting up

Install the projector according to the environment and manner the projector will be used in.

Arrangement

Refer to the illustrations and tables below to determine screen size and projection distance.

The values shown in the table are calculated for a full size screen: 1280 x 800 a Screen size (diagonal) b

c1 , c2 Screen height (±10%)

Projection distance (±10%, from the projector's end)

On a horizontal surface

Suspended from the ceiling

• Keep a space of 30 cm or more between the sides of the projector and other objects such as walls.

• For the case of installation in a special state such as ceiling mount, the specied mounting accessories (

69) and service may

be required. Before installing the projector, consult your dealer about your installation.

Screen size

(diagonal)

type

(inch)

30 0.8 0.9 36 1.1 44 40 16 0 0 1.0 41 1.3 50 47 18 -1 0 40 1.0 1.2 49 1.5 59 54 21 0 0 1.4 56 1.7 67 62 25 -1 -1 50 1.3 1.6 61 1.9 74 67 26 0 0 1.8 70 2.1 84 78 31 -2 -1 60 1.5 1.9 74 2.3 89 81 32 0 0 2.1 84 2.6 101 93 37 -2 -1 70 1.8 2.2 87 2.7 105 94 37 0 0 2.5 99 3.0 119 109 43 -2 -1 80 2.0 2.5 100 3.0 120 108 42 0 0 2.9 113 3.5 136 124 49 -3 -1

90 2.3 2.9 112 3.4 135 121 48 0 0 3.2 127 3.9 153 140 55 -3 -1 100 2.5 3.2 125 3.8 150 135 53 0 0 3.6 142 4.3 170 156 61 -3 -1 120 3.0 3.8 150 4.6 181 162 64 0 0 4.3 170 5.2 205 187 74 -4 -2 150 3.8 4.8 188 5.8 200 5.1 6.4 252 7.7 303 269 106 0 0 7.2 285 8.7 343 311 123 -6 -3 250 6.4 8.0 315 9.6 379 337 132 0 0 9.1 357 10.9 429 389 153 -8 -3 300 7.6 9.6 379 11.6 455 404 159 0 0 10.9 429 13.1 515 467 184 -10 -4

Projection distance

min. max. min. max.

m m inch m inch cm inch cm inch m inch m inch cm inch cm inch

16 : 10 screen 4 : 3 screen

227 202 79 0 0 5.4 214 6.5 257 233 92 -5 -2

c1 c2

Screen

height

Screen

height

Projection distance

Screen

height

Screen

height

Page 17

Setting up

Arrangement (continued)

WARNING

►Place the projector in a stable horizontal position. If the projector falls or is knocked over, it could cause injury and/or damage to the projector. Using a damaged projector could then result in re and/or electric shock.

• Do not place the projector on an unstable, slanted or vibrational surface such

as a wobbly or inclined stand.

• Do not place the projector on its side, front or rear position.

• Consult with your dealer before a special installation such as suspending from

a ceiling or somewhere else. ►Place the projector in a cool place, and ensure that there is sufcient ventilation. The high temperature of the projector could cause re, burns and/or malfunction of the projector.

• Do not place or attach anything that would block the lens or vent holes.

• Keep a space of 30 cm or more between the sides of the projector and other

objects such as walls.

• Do not place the projector on metallic thing or anything weak in heat.

• Do not place the projector on carpet, cushions or bedding.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

• Do not place anything near the projector lens or vents, or on top of the

projector.

•

Do not place anything that may be sucked into or stick to the vents on the

bottom of the projector. This projector has some intake vents also on the bottom. ►Do not place the projector anyplace where it may get wet. Getting the projector wet or inserting liquid into the projector could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector in a bathroom or the outdoors.

• Do not place anything containing liquid near the projector. ►Do not place the projector where any oils, such as cooking or machine oil, are used. ►Use only the mounting accessories the manufacturer specied, and leave installing and removing the projector with the mounting accessories to the service personnel.

• Read and keep the user’s manual of the mounting accessories used.

CAUTION

►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector near humidiers, smoking spaces or a kitchen. Also

do not use an ultrasonic humidier near the projector. Otherwise chlorine and minerals contained in tap water are atomized and could be deposited in the

projector causing image degradation or other problems. ►Position the projector to prevent light from directly hitting the projector's remote sensor.

Page 18

Setting up

Connecting your devices

Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them. To input component video signal to COMPUTER IN port, please see the description of the COMPUTER IN item of the INPUT menu (35).

PCMonitor

RGB IN

AUDIO OUT

RGB OUT

AUDIO OUT

RS-232C

L R

AUDIO OUT

VIDEO OUT

AUDIO OUT

S-VIDEO OUT

HDMI

L R

AUDIO OUT

COMPONENT VIDEO OUT

L R

AUDIO IN

Y CB/PB CR/PR

Speakers

(with an

amplier)

VCR/DVD/Blu-ray Disc player

WARNING

►Do not disassemble or modify the projector and accessories.

►Be careful not to damage the cables, and do not use damaged cables.

CAUTION

►Turn off all devices and unplug their power cords prior to connecting them to projector. Connecting a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction or damage to the device and the projector. ►Use appropriate accessory or designated cables. Ask your dealer about nonaccessory cables which may be required a specic length or a ferrite core by the regulations. For cables with a core only at one end, connect the end with the core to the projector. ►Make sure that devices are connected to the correct ports. An incorrect connection may result in malfunction or damage to the device and the projector.

NOTICE

►Use the cables with straight plugs, not L-shaped ones, as the

input ports of the projector are recessed.

Page 19

Setting up

Connecting your devices (continued)

NOTE

• Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution.

- Some signal may need an adapter to input this projector.

- Some PCs have multiple screen display modes that may include some signals

which are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA

(1600X1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical.

• While connecting, make sure that the shape of the cable's connector ts the port to connect with. And be sure to tighten the screws on connectors with screws.

• When connecting a laptop PC to the projector, be sure to activate the PC’s external RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT display.) For details on how this is done, please refer to the instruction manual of the corresponding laptop PC.

• When the picture resolution is changed on a PC depending on an input, automatic adjustment function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution.

• In some cases, this projector may not display a proper picture or display any picture on screen. For example, automatic adjustment may not function correctly with some input signals. An input signal of composite sync or sync on G may confuse this projector, so the projector may not display a proper picture.

About Plug-and-Play capability

Plug-and-Play is a system composed of a PC, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-Play can be used by connecting this projector to a PC that is VESA DDC (display data channel) compatible.

• Take advantage of this feature by connecting a computer cable to the COMPUTER IN port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

• Please use the standard drivers in your PC as this projector is a Plug-andPlay monitor.

Page 20

Setting up

Connecting power supply

Put the connector of the power cord into the

AC IN (AC inlet) of the projector. Firmly plug the power cord’s plug into the

outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.

Please remember that when the DIRECT POWER

ON function activated (46), the connection of

the power supply make the projector turn on.

WARNING

incorrect or faulty connections may result in re and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one.

• Only plug the power cord into an outlet whose voltage is matched to the power cord. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

• Never modify the power cord.

►Please use extra caution when connecting the power cord, as

AC IN

Power cord

Using the security bar and slot

A commercially available anti-theft chain or wire can be attached to the security bar on the projector. Refer to the gure to choose an anti-theft chain or wire. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool.

12 mm

18 mm

10 mm

WARNING

from falling down, since it is not designed for it.

CAUTION

may become too hot.

NOTE

measures. It is intended to be used as supplemental theft prevention measure.

• The security bar and slot is not comprehensive theft prevention

►Do not use the security bar and slot to prevent the projector

►Do not place anti-theft chain or wire near the exhaust vents. It

Installation surface

Security slot

Security bar

Anti-theft chain or wire

Page 21

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

Holding the hook part of the battery

cover, remove it. Align and insert the two AA batteries

(HITACHI MAXELL, Part No.LR6 or R6P) according to their plus and minus terminals as indicated in the remote control. Replace the battery cover in the direction of the arrow and snap it back into place.

213

WARNING

directed. Improper use may result in battery explosion, cracking or leakage, which could result in re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

• If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

►Always handle the batteries with care and use them only as

About the remote control signal

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

•

NOTE

If it is difcult to send the signal to the sensor directly, attempt to make the signal reect.

• The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

The remote control may not work correctly if strong light (such as direct sun

• light) or light from an extremely close range (such as from an inverter uorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

The remote control signal reected in the screen or the like may be available.

Approx.

3 m

30º

Page 22

Power on/off

Turning on the power

Make sure that the power cord is rmly and

correctly connected to the projector and the outlet. Make sure that the POWER indicator is

steady orange (63). Then remove the lens cover.

Press STANDBY/ON button on the

projector or the remote control. The projection lamp will light up and POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green (63).

To display the picture, select an input signal according to the section “Selecting an input signal” (15).

STANDBY/ON button POWER indicator

MY SOURCE/

COMPUTER

DOC.CAMERA

VIDEO

AUTO

ASPECT SEARCH

BLANK

PAGEUPVOLUME

FREEZE

MAGNIFY

DOWN

KEYSTONE

MY BUTTON

MUTE

POSITION

ENTER

ESC

㧗

࡯ONOFF

RESET

Turning off the power

Press the STANDBY/ON button on the projector or the remote control. The

message “Power off?” will appear on the screen for about 5 seconds. Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete (63).

Attach the lens cover, after the POWER indicator turns in steady orange.

Do not turn the projector on for about 10 minutes or more after turning it off. Also, do not turn the projector off shortly after turning it on. Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

WARNING

►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings. ►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE

• Turn the power on/off in right order. Please power on the projector

prior to the connected devices.

•

This projector has the function that can make the projector automatically turn on/ off. Please refer to the DIRECT POWER ON items of the OPTION menu.

(46)

and AUTO POWER OFF

(47)

Page 23

Power on/off

Precaution for lens cover attachment and removal

When you attach or remove the lens cover, move it vertically up and down while keeping the knob to the right as illustrated in the gure.

Page 24

Operating

Adjusting the volume

Use the VOLUME +/VOLUME - buttons to adjust the volume.

A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after a few seconds.

● When

is selected for current picture input port, the volume

VOLUME +/- button

MY SOURCE/

COMPUTER

DOC.CAMERA

VIDEO

AUTO

ASPECT SEARCH

FREEZE

MAGNIFY

OFF

KEYSTONE

MY BUTTON

adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (39).

POSITION

● Even if the projector is in the standby state, the volume can be adjusted when both of following conditions are satised.

- NORMAL is selected for the STANDBY MODE in the SETUP menu (38).

- An item other than is selected for the AUDIO OUT STANDBY of the

AUDIO SOURCE in the AUDIO menu (39).

Temporarily muting the sound

Press MUTE button on the remote control.

A dialog will appear on the screen indicating that you have muted the sound. To restore the sound, press the MUTE, VOLUME + or VOLUME - button. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● When is selected for current picture input port, the sound

MUTE button

MY SOURCE/

COMPUTER

DOC.CAMERA

VIDEO

AUTO

ASPECT SEARCH

FREEZE

MAGNIFY

OFF

KEYSTONE

MY BUTTON

POSITION

is always muted. Please see AUDIO SOURCE item of AUDIO menu (39).

● C.C. (Closed Caption) is automatically activated when sound is muted and an input signal containing C.C. is received. This function is available only when the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPUTER IN, and when AUTO is selected for DISPLAY in the C.C. menu under the SCREEN menu (45).

Selecting an input signal

Press INPUT button on the projector.

Each time you press the button, the projector switches its input port from the current port as below.

INPUT button

BLANK

PAGE

VOLUME

㧗

DOWN

࡯

MUTE

BLANK

PAGE

VOLUME

㧗

DOWN

࡯

MUTE

COMPUTER IN Æ HDMI

VIDEO Æ S-VIDEO

● While ON is selected for AUTO SEARCH item in OPTION menu (46), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

(continued on next page)

Page 25

Operating

Selecting an input signal (continued)

Press COMPUTER button on the remote control to

select the COMPUTER IN port.

Press VIDEO button on the remote control.

Each time you press the button, the projector switches its input port from the current port as below.

HDMI

S-VIDEO Æ VIDEO

●

While ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till an input signal is detected (46). If VIDEO button is pressed when COMPUTER IN port is selected, the projector will check HDMI port rst.

Press the MY SOURCE / DOC. CAMERA button on

the remote control. The input signal will be changed into the signal you set as MY SOURCE (48).

● This function also can use for document camera. Select the input port that connected the document camera.

COMPUTER button

MY SOURCE/

COMPUTER

DOC.CAMERA

VIDEO

AUTO

ASPECT SEARCH

MAGNIFY

OFF

KEYSTONE

POSITION

FREEZE

MY BUTTON

PAGE UP

DOWN

BLANK

VOLUME

MUTE

㧗

࡯

VIDEO button

MY SOURCE/

COMPUTER

DOC.CAMERA

VIDEO

AUTO

ASPECT SEARCH

MAGNIFY

OFF

KEYSTONE

POSITION

FREEZE

MY BUTTON

PAGE UP

DOWN

BLANK

VOLUME

MUTE

㧗

࡯

MY SOURCE / DOC. CAMERA button

MY SOURCE/

COMPUTER

DOC.CAMERA

VIDEO

AUTO

ASPECT SEARCH

MAGNIFY

OFF

KEYSTONE

FREEZE

MY BUTTON

PAGE UP

DOWN

BLANK

VOLUME

MUTE

㧗

࡯

POSITION

Page 26

Operating

Searching an input signal

Press SEARCH button on the remote control.

The projector will start to check its input ports as below in order to nd any input signals. When an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

COMPUTER IN Æ HDMI

VIDEO Æ S-VIDEO

SEARCH button

COMPUTER

VIDEO

ASPECT SEARCH

FREEZE

MAGNIFY

OFF

KEYSTONE

POSITION

● While ON is selected for AUTO SEARCH item in OPTION menu (46), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

Selecting an aspect ratio

Press ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

 For a computer signal

NORMAL Æ 4:3 Æ 16:9 Æ 16:10 Æ NATIVE

 For an HDMI signal

NORMAL Æ 4:3 Æ 16:9 Æ 16:10 Æ 14:9 Æ NATIVE

ASPECT button

COMPUTER

VIDEO

ASPECT SEARCH

FREEZE

MAGNIFY

OFF

KEYSTONE

POSITION

AUTO

MY BUTTON

AUTO

MY BUTTON

MY SOURCE/ DOC.CAMERA

PAGE UP

DOWN

MY SOURCE/ DOC.CAMERA

PAGE UP

DOWN

BLANK

VOLUME

MUTE

BLANK

VOLUME

MUTE

㧗

࡯

㧗

࡯

 For a video signal, s-video signal or component video

signal

4:3 Æ 16:9 Æ 16:10 Æ 14:9 Æ NATIVE

 For no signal

16:10 (xed)

● ASPECT button does not work when no proper signal is inputted.

● NORMAL mode keeps the original aspect ratio setting.

Page 27

Operating

12°

Adjusting the projector's elevator

When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 12 degrees. This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is adjustable while pulling up the elevator knob on the same side as it.

Holding the projector, pull the elevator knobs up to loose the elevator feet.

Position the front side of the projector to the desired height.

Release the elevator knobs in order to lock the elevator feet.

After making sure that the elevator feet are locked, put the projector down

gently. If necessary, the elevator feet can be manually twisted to make more precise

adjustments. Hold the projector when twisting the feet.

To loose an elevator foot, pull up the elevator knob on the same side as it.

CAUTION

projector, since the projector may drop down. ►Do not tilt the projector other than elevating its front within 12 degrees using the adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables, or the projector itself.

►Do not handle the elevator buttons without holding the

Adjusting the zoom and focus

Use the zoom ring to adjust the screen size.

Use the focus ring to focus the picture.

To nely adjust, twist the foot.

Zoom ring

Focus ring

Page 28

Operating

Using the automatic adjustment feature

Press AUTO button on the remote control.

Pressing this button performs the following.

 For a computer signal

The vertical position, the horizontal position and the horizontal phase will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

 For a video signal and s-video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT menu (

34). The vertical position and

horizontal position will be automatically set to the default.

 For a component video signal

The vertical position and horizontal position will be automatically set to the default. The horizontal phase will be automatically adjusted.

● The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input.

● When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

● When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the PC model. The items adjusted by this function may vary when the FINE or DISABLE is selected

● for the AUTO ADJUST item of the SERVICE item in the OPTION menu (

AUTO button

COMPUTER

VIDEO

AUTO

ASPECT SEARCH

FREEZE

MAGNIFY

OFF

KEYSTONE

POSITION

49).

MY SOURCE/ DOC.CAMERA

PAGE UP

MY BUTTON

BLANK

VOLUME

㧗

DOWN

࡯

MUTE

Adjusting the position

KEYSTONE

POSITION

ESC

MY BUTTON

ENTER

Press POSITION button on the remote control when no menu is

indicated. The “POSITION” indication will appear on the screen.

Use the ▲/▼/◄/► cursor buttons to adjust the picture position.

When you want to reset the operation, press RESET button on the remote control during the operation. To complete this operation, press POSITION button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

When this function is performed on a video signal or s-video signal or component

●

POSITION button

video signal, some image such as an extra-line may appear at outside of the picture.

● When this function is performed on a video signal or an s-video signal, the range of this adjustment depends on OVER SCAN in IMAGE menu (

30) setting. It is

not possible to adjust when OVER SCAN is set to 10.

● If POSITION button is pressed when a menu is indicated on screen, the displayed picture does not move its position but the menu does.

● This function is unavailable for a signal from the HDMI port.

MUTE

RESET

Page 29

Operating

Correcting the keystone distortions

Press KEYSTONE button on the remote

control. A dialog will appear on the screen to aid you in correcting the distortion.

Use the ▲/▼ cursor buttons to select AUTO or MANUAL

operation, and press the ► button to perform the following.

KEYSTONE button

MY SOURCE/

COMPUTER

DOC.CAMERA

VIDEO

AUTO

ASPECT SEARCH

PAGE

FREEZE

MAGNIFY

DOWN

OFF

KEYSTONE

MY BUTTON

(1) AUTO executes automatic vertical keystone correction. (2) MANUAL displays a dialog for keystone correction.

Use the ◄/► buttons for adjustment.

To close the dialog and complete this operation, press KEYSTONE button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● The adjustable range of this function will vary among inputs. For some input, this function may not work well.

● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, automatic vertical keystone correction may not work correctly.

● When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.

● When the projector is placed on the level (about ±

4°), the automatic keystone

distortion correction may not work.

● When the projector is inclined to near ±30 degree or over, this function may not work well.

● This function will be unavailable when Transition Detector is on (

54).

BLANK

VOLUME

㧗

࡯

MUTE

Page 30

Operating

Using the magnify feature

Press the MAGNIFY ON button on the remote control. The

picture will be magnied, and the MAGNIFY dialog will appear on the screen. When the MAGNIFY ON button is pressed for the rst time after the projector is turned on, the picture will be zoomed by 1.5 times. On the dialog, triangle marks to show each direction will be displayed.

While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor buttons

to shift the magnifying area.

A magnifying glass icon will be displayed on the dialog when the MAGNIFY ON

button is pressed while the dialog with the triangles is displayed.

While the magnifying glass icon is displayed on the dialog, use the ▲/▼ cursor

buttons to adjust the magnication ratio. The magnication ratio will be adjusted

MAGNIFY ON/OFF button

MY SOURCE/

COMPUTER

DOC.CAMERA

VIDEO

AUTO

ASPECT SEARCH

PAGE

FREEZE

MAGNIFY

DOWN

OFF

KEYSTONE

MY BUTTON

with ne steps. And changes in the ratio in single steps are subtle so they may be hard to recognize.

Press the MAGNIFY OFF button on the remote control to exit magnication.

● The MAGNIFY dialog will automatically disappear in several seconds with no operation. The dialog will appear again if the MAGNIFY ON button is pressed when the dialog has automatically disappeared.

● While the MAGNIFY dialog is displayed, press the MAGNIFY ON button to switch the dialog between magnifying area shifting (with the triangles) and magnication ratio adjustment (with the magnifying glass icon).

● The magnication is automatically disabled when the displaying signal or its display condition is changed.

● While the magnication is active, the keystone distortion condition may vary. It will be restored when the magnication is disabled.

● Some horizontal stripes might be visible on the image while magnication is active.

BLANK

VOLUME

MUTE

㧗

࡯

Page 31

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

Temporarily freezing the screen

Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen (however,

FREEZE button

the indication will not appear when the OFF is selected for the MESSAGE item in the SCREEN menu (

42)), and the projector will go into the FREEZE mode, which the picture is frozen. To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again.

● The projector automatically exits from the FREEZE mode when some control buttons are pressed.

● If the projector continues projecting a still image for a long time, the LCD panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long.

● Images might appear degraded when this function is operated, but it is not a malfunction.

Temporarily blanking the screen

Press the BLANK button on the control panel or the remote

control. The BLANK screen will be displayed instead of

the screen of input signal. Please refer to BLANK item in SCREEN menu (40). To exit from the BLANK screen and return to the input signal screen, press BLANK button again.

● The projector automatically exits from the

BLANK

mode

when some control buttons are pressed.

● You can change the function assigned to the BLANK button on the control panel by the MY BUTTON function. Please refer to MY BUTTON item in OPTION menu (48).

BLANK button

%/$1.

0<%87721

CAUTION

►If you wish to have a blank screen while the projector's lamp is on, use the BLANK function above. Any other method of blocking the projection light, such as attaching something to the lens or placing something in front of the lens, may cause the damage to the projector.

•

NOTE

necessary, set the volume or mute rst. To display the BLANK screen and mute the sound at one time, use AV MUTE function

The sound is not connected with the BLANK screen function. If

(48).

Page 32

Operating

Using the menu function

This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, SECURITY and EASY MENU. EASY MENU consists of functions often used, and the other menus are classied into each purpose and brought together as the ADVANCED MENU. Each of these menus is operated using the same methods. While the projector is displaying any menu, the MENU button on the projector works as the cursor buttons. The basic operations of these menus are as follows.

INPUT button

ENTER button MENU button

Cursor buttons

ENTER

RESET

VIDEO

ASPECT SEARCH

MAGNIFY

KEYSTONE

POSITION

ESC

MENU button

POSITION

ESC

(Cursor buttons)

ESC button

To start the MENU, press the MENU button. The MENU you last used (EASY

or ADVANCED) will appear. EASY MENU has priority to appear just after

RESET button

powered on.

In the EASY MENU

(1) Use the ▲/▼ cursor buttons to select an item to

operate. If you want to change it to the ADVANCED MENU, select the ADVANCED MENU.

(2) Use the ◄/► cursor buttons to operate the item.

In the ADVANCED MENU

(1) Use the ▲/▼ cursor buttons to select a menu.

If you want to change it to the EASY MENU, select the EASY MENU. The items in the menu appear on the right side.

(2) Press the ► cursor button or ENTER button to

move the cursor to the right side. Then use the ▲/▼ cursor buttons to select an item to operate and press the ► cursor button or ENTER button to progress. The operation menu or dialog of the selected item will appear.

(3) Use the buttons as instructed in the OSD to operate the item.

MY SOURCE/

COMPUTER

DOC.CAMERA

AUTO

BLANK

PAGE

VOLUME

FREEZE

㧗

DOWN

࡯ONOFF

MY BUTTON

MUTE

ENTER

RESET

(continued on next page)

Page 33

Operating

Using the menu function (continued)

To close the MENU, press the MENU button again or select EXIT and press

the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds.

●

If you want to move the menu position, use the cursor buttons after pressing the POSITION button.

● Some functions cannot be performed when a certain input port is selected, or when a certain input signal is displayed.

● When you want to reset the operation, press RESET button on the remote control during the operation. Note that some items (ex. LANGUAGE, VOLUME) cannot be reset.

● In the ADVANCED MENU, when you want to return to the previous display, press the ◄ cursor button or ESC button on the remote control.

Indication in OSD (On Screen Display)

The meanings of the general words on the OSD are as follows.

Indication Meaning

EXIT

RETURN Selecting this word returns the menu to the previous menu.

CANCEL or NO

OK or YES

Selecting this word nishes the OSD menu. It's the same as pressing the MENU button.

Selecting this word cancels the operation in the present menu and returns to the previous menu.

Selecting this word executes the prepared function or shifts the menu to the next menu.

Page 34

EASY MENU

From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table.

Item Description

ASPECT

AUTO KEYSTONE

KEYSTONE

Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGEmenu

Using the ► button executes the auto keystone function. See the AUTO KEYSTONE item in SETUP menu (37).

Using the ◄/► buttons corrects the vertical keystone distortion. See the KEYSTONE item in SETUP menu

Using the ◄/► buttons switches the picture mode. The picture modes are combinations of GAMMA and COLOR

TEMP settings. Choose a suitable mode according to the projected source.

NORMAL Ù CINEMA Ù DYNAMIC Ù BOARD(BLACK)

(30).

(37).

EASY MENU

PICTURE MODE

• When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and COLOR TEMP (

• Lines or other noise might appear on the screen when this function is operated, but it is not a malfunction.

(continued on next page)

DAYTIME Ù WHITEBOARD Ù BOARD(GREEN)

GAMMA COLOR TEMP NORMAL 1 DEFAULT 2 MID CINEMA 2 DEFAULT 3 LOW DYNAMIC 3 DEFAULT 1 HIGH BOARD(BLACK) 4 DEFAULT 4 Hi-BRIGHT-1 BOARD(GREEN) 4 DEFAULT 5 Hi-BRIGHT-2 WHITEBOARD 5 DEFAULT 2 MID DAYTIME 6 DEFAULT 6 Hi-BRIGHT-3

27, 28) items in PICTURE menu.



Page 35

EASY MENU

Item Description

ECO MODE

MIRROR

Using the ◄/► buttons changes the eco mode setting. See the ECO MODE item in SETUP menu (

Using the ◄/► buttons switches the mode for mirror status. See the MIRROR item in SETUP menu (

Performing this item resets all of the EASY MENU items except the

RESET

FILTER TIME and LANGUAGE. A dialog is displayed for conrmation. Selecting the OK using the button performs resetting.

The usage time of the air lter is shown in the menu. Performing this item resets the lter time which counts usage time

FILTER TIME

of the air lter. A dialog is displayed for conrmation. Selecting the OK using the button performs resetting. See the FILTER TIME item in OPTION menu (

LANGUAGE

ADVANCED MENU

EXIT Press the

Using the ◄/► buttons changes the display language. See the LANGUAGE item in SCREEN menu

Press the ► or ENTER button to use the menu of PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION or SECURITY.

◄ or

ENTER

button to nish the OSD menu.



38).



(40).

38).



47).

►

Page 36

PICTURE menu

From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

BRIGHTNESS

CONTRAST

Using the

Dark Ù Light

Using the

Weak Ù Strong

Using the ▲/▼ buttons switches the gamma mode.

DEFAULT-1Ù CUSTOM-1 Ù DEFAULT-2Ù CUSTOM-2 Ù DEFAULT-3

CUSTOM-6 CUSTOM-3

ÙÙ

◄/►

buttons adjusts the brightness.

◄/►

buttons adjusts the contrast.

PICTURE menu

ÙÙ

Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones.

Choose an item using the ◄/► buttons, and adjust the level using the ▲/▼ buttons.

GAMMA

(continued on next page)

You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.

No pattern Ö Gray scale of 9 steps Ramp Õ Gray scale of 15 steps

The eight equalizing bars correspond to eight tone levels of the test pattern (Gray scale of 9 steps) except the darkest in the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalizing adjustment bar “1”. The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar.

• Lines or other noise might appear on the screen when this function is operated, but it is not a malfunction.

DEFAULT-6

To adjust CUSTOM

CUSTOM-5 Ù DEFAULT-5Ù CUSTOM-4 Ù DEFAULT-4

Page 37

PICTURE menu

1 HIGH Ù 1 CUSTOM Ù2 MID Ù 2 CUSTOM

3 LOW

5 CUSTOM

5 Hi-BRIGHT-2Ù4 CUSTOMÙ4 Hi-BRIGHT-1

6 CUSTOM

ÙÙÙ

6 Hi-BRIGHT-3

3 CUSTOM

Item Description

Using the ▲/▼ buttons switches the color temperature mode.

To adjust CUSTOM

Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and

COLOR TEMP

GAIN of the selected mode. OFFSET adjustments change the color intensity

on the whole tones of the test pattern. GAIN adjustments mainly affect color intensity

on the brighter tones of the test pattern. Choose an item using the ◄/► buttons, and adjust the level using

the ▲/▼ buttons. You can display a test pattern for checking the effect of your

adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.

No pattern Ö Gray scale of 9 steps

•

Lines or other noise might appear on the screen when

Ramp Õ Gray scale of 15 steps

this function is operated, but it is not a malfunction. Using the ◄/► buttons adjusts the strength of whole color.

Weak Ù Strong

• This item can be selected only for a video, s-video and component

COLOR

video signal.

•

For an HDMI signal, this item can also be selected if either (1) or (2) applies.

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO. (2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

Using the ◄/► buttons adjusts the tint.

Reddish Ù Greenish

• This item can be selected only for a video, s-video and component

TINT

(continued on next page)

video signal.

•

For an HDMI signal, this item can also be selected if either (1) or (2) applies.

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO. (2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

Page 38

Item Description

Using the ◄/► buttons adjusts the sharpness.

SHARPNESS

Weak Ù Strong

• There may be some noise and/or the screen may icker for a moment when an adjustment is made. This is not a malfunction.

This projector has 4 memories for adjustment data (for all the items of the PICTURE menu). Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER button performs each function.

SAVE-1 Ù SAVE-2 Ù SAVE-3 Ù SAVE-4 LOAD-4 ÙLOAD-3 Ù LOAD-2 Ù LOAD-1

SAVE-1, SAVE-2, SAVE-3, SAVE-4 Performing a SAVE function saves the current adjustment data into the memory linked in the number included in the function’s name.

• Remember that the current data being stored of a memory will be lost by saving new data into the memory.

MY MEMORY

LOAD-1, LOAD-2, LOAD-3, LOAD-4 Performing a LOAD function loads the data from the memory linked in the number included in the function’s name, and adjusts the picture automatically depending on the data.

• The LOAD functions whose linked memory has no data are skipped.

• Remember that the current adjusted condition will be lost by loading data. If you want to keep the current adjustment, please save it before performing a LOAD function.

• There may be some noise and the screen may icker for a moment when loading data. This is not malfunction.

• You can perform the LOAD function using MY BUTTONs. Please see MY BUTTON item in OPTION menu (



PICTURE menu

48).

Page 39

IMAGE menu

From the IMAGE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ▲/▼ buttons switches the mode for aspect ratio.

For a computer signal

NORMAL Ù 4:3 Ù 16:9 Ù 16:10 Ù NATIVE

For an HDMI signal

NORMAL Ù 4:3 Ù 16:9 Ù 16:10 Ù 14:9 Ù NATIVE

ASPECT

OVER SCAN

(continued on next page)

For a video signal, s-video signal or component video signal

4:3 Ù 16:9 Ù 16:10 Ù 14:9 Ù NATIVE

For no signal

16:10 (xed)

• The NORMAL mode keeps the original aspect ratio of the signal. Using the ◄/► buttons adjusts the over-scan ratio.

Small (It magnies picture) Ù Large (It reduces picture)

• This item can be selected only for a video, s-video and component video signal.

•

For an HDMI signal, this item can also be selected if either (1) or (2) applies.

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO. (2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

Page 40

Item Description

Using the ◄/► buttons adjusts the vertical position.

• Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs, please reset the vertical position to the

V POSITION

default setting. Pressing the RESET button when the V POSITION is selected will reset the V POSITION to the default setting.

• When this function is performed on a video signal or an s-video

signal, the range of this adjustment depends on OVER SCAN (

setting. It is not possible to adjust when OVER SCAN is set to 10.

• This function is unavailable for a signal from the HDMI port. Using the ◄/► buttons adjusts the horizontal position.

• the screen. If this occurs, please reset the horizontal position to the

H POSITION

default setting. Pressing the RESET button when the H POSITION is selected will reset the H POSITION to the default setting.

• When this function is performed on a video signal or an s-video

signal, the range of this adjustment depends on OVER SCAN (

setting. It is not possible to adjust when OVER SCAN is set to 10.

• This function is unavailable for a signal from the HDMI port.

(continued on next page)

IMAGE menu

Down Ù Up

30)



Right Ù Left

Over-adjusting the horizontal position may cause noise to appear on

30)



Page 41

IMAGE menu

Item Description

Using the

◄/►

buttons adjusts the horizontal phase to eliminate icker.

Right Ù Left

H PHASE

• This item can be selected only for a computer signal or a component video signal.

• This function is unavailable for a signal from the HDMI port. Using the ◄/► buttons adjusts the horizontal size.

Small Ù Large

• This item can be selected only for a computer signal.

• This function is unavailable for a signal from the HDMI port.

H SIZE

• When this adjustment is excessive, the picture may not be displayed correctly. In such a case, please reset the adjustment by pressing the RESET button on the remote control during this operation.

• Images might appear degraded when this function is operated, but it is not a malfunction.

Selecting this item performs the automatic adjustment feature.

For a computer signal

For a video signal and s-video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT

AUTO ADJUST

EXECUTE

menu ( automatically set to the default.

For a component video signal

34). The vertical position and horizontal position will be



The vertical position and horizontal position will be automatically set to the default. The horizontal phase will be automatically adjusted.

• The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input.

• When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

• When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the PC model.

• The items adjusted by this function may vary when the FINE or DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu (



49).

Page 42

INPUT menu

From the INPUT menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ▲/▼ buttons switches the progress mode.

TV Ù FILM Ù OFF

• This function works only for a video signal, s-video signal,

PROGRESSIVE

VIDEO NR

COLOR SPACE

(continued on next page)

component video signal (of 480i@60 or 576i@50) and an HDMI signal (of 480i@60 or 576i@50).

• When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select OFF, even though the screen image may lose sharpness.

Using the ▲/▼ buttons switches the noise reduction mode.

HIGH Ù MID Ù LOW

• This function works only for a video signal, s-video signal, component video signal (of 480i@60 or 576i@50) and an HDMI signal (of 480i@60 or 576i@50).

Using the ▲/▼ buttons switches the mode for color space.

AUTO Ù RGB Ù SMPTE240 Ù REC709 Ù REC601

• This item can be selected only for a computer signal or a component video signal.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well at some signals. In such a case, it might be good to select a suitable mode except AUTO.

INPUT menu

Page 43

INPUT menu

Item Description

The video format for S-VIDEO port and VIDEO port can be set. (1) Use the ▲/▼ buttons to

(2) Using the ◄/► buttons

VIDEO FORMAT

• This item is performed only for a video signal from the VIDEO port or the S-VIDEO port.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well for some signals. If the picture becomes unstable (e.g. an irregular picture, lack of color), please select the mode according to the input signal.

Using the ▲/▼ cursor buttons switches the video format for an input from the HDMI port.

HDMI FORMAT

• When the COMPUTER is selected, the functions COLOR (PICTURE menu), TINT (PICTURE menu) and OVER SCAN (IMAGE menu) are unavailable.

Using the ▲/▼ cursor buttons changes the digital range for input from the HDMI port.

HDMI RANGE

• If the contrast of the screen image is too strong or too weak, try nding a more suitable mode.

(continued on next page)

select the input port.

S-VIDEO Ù VIDEO

switches the mode for video format.

AUTO Ù NTSC Ù PAL Ù SECAM N-PAL Ù M-PAL Ù NTSC4.43

AUTO Ù VIDEO Ù COMPUTER

Feature AUTO automatically sets the optimum mode. VIDEO sets the suitable mode for DVD signals. COMPUTER sets the suitable mode for computer signals.

AUTO Ù NORMAL Ù ENHANCED

Feature AUTO automatically sets the optimum mode. NORMAL s ENHANCED

ets the suitable mode for DVD signals. (16-

235)

sets the suitable mode for computer signals. (0-255)

Page 44

Item Description

Use the ◄/► buttons to select the computer input signal type.

• Selecting the AUTO mode allows you to input a sync on G signal

COMPUTER IN

or component video signal from the port. To input component video signal to the projector, an RCA to D-sub cable or adapter is required.

• In the AUTO mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and select the SYNC ON G OFF, and then reconnect the signal.

Set the frame lock function on/off for each port. (1) Use the ▲/▼ buttons to select the input ports.

(2) Use the ◄/► buttons to turn the

FRAME LOCK

• This item can be performed only on a signal with a vertical frequency of 50 to 60 Hz.

• When ON is selected, moving pictures are displayed more smoothly.

(continued on next page)

INPUT menu

AUTO Ù SYNC ON G OFF

COMPUTER IN Ù HDMI

frame lock function on/off .

ON Ù OFF

Page 45

INPUT menu

Item Description

The resolution for the COMPUTER IN input signals can be set on this projector.

(1) In the INPUT menu select the RESOLUTION using the ▲/▼

buttons and press the ► button. The RESOLUTION menu will be displayed.

(2) In the RESOLUTION menu select the

resolution you wish to display using the ▲/▼ buttons. Selecting AUTO will set a resolution appropriate to the input signal.

(3) Pressing the ► or ENTER button when

selecting a STANDARD resolution will automatically adjust the horizontal and vertical positions, clock phase and

horizontal size. The INPUT_INFORMATION dialog will be displayed.

(4) To set a custom resolution use the ▲/▼ buttons to select

RESOLUTION

the CUSTOM and the RESOLUTION_CUSTOM box will be

displayed. Set the horizontal (HORZ) and vertical (VERT) resolutions using the ▲/▼/◄/► buttons. This function may not support all resolutions.

(5) Move the cursor to OK on screen and press the ► or ENTER

button. The message “ARE YOU SURE YOU WISH TO

CHANGE RESOLUTION?” appears. To save the setting, press

the ► button.

The horizontal and vertical positions, clock phase and horizontal

size will be automatically adjusted. The INPUT_INFORMATION dialog will be displayed.

(6) To revert back to the previous resolution without saving

changes, move the cursor to CANCEL on screen and press the

◄ or ENTER button.

The screen will then return to the RESOLUTION menu

displaying the previous resolution.

• For some pictures, this function may not work well.

STANDARD

↓

CUSTOM

↓

Page 46

SETUP menu

From the SETUP menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Selecting this item performs the Automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself. This function will be executed only once when selected in the menu. When the slant of the projector is changed, execute this function again.

• The adjustable range of this function will vary among inputs. For some input, this function may not work well.

• When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled

AUTO KEYSTONE

KEYSTONE

AUTO ECO

MODE

(continued on next page)

downward, this function may not work correctly.

• When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.

• When the projector is placed on the level (about ±4°), this function may not work.

• When the projector is inclined to near ±30 degree or over, this function may not work well.

• This function will be unavailable when the Transition Detector is on (

54).



Using the ◄/► buttons corrects the vertical keystone distortion.

Shrink the bottom of the image Ù Shrink the top of the image

• The adjustable range of this function will vary among inputs. For some input, this function may not work well.

• This function will be unavailable when the Transition Detector is on (

54).



Using the ▲/▼ buttons turns on/off the AUTO ECO MODE.

ON Ù OFF

• When ON is selected, the projector will always be set to Eco mode at start-up regardless of the ECO MODE ( message “AUTO ECO MODE” will be displayed for tens of seconds when the projector starts with this function activated.

SETUP menu

38) setting. An OSD



Page 47

SETUP menu

Item Description

Using the ▲/▼ buttons changes the eco mode setting.

ECO MODE

NORMAL Ù ECO

• When the ECO is selected, acoustic noise and screen brightness are reduced.

Using the ▲/▼ buttons switches the mode for mirror status.

MIRROR

STANDBY MODE

MONITOR OUT

NORMAL Ù H:INVERT Ù V:INVERT Ù H&V:INVERT

If the Transition Detector is on and MIRROR status is changed, TRANSITION DETECTOR ON alarm (

54) will be displayed when



projector is restarted after the AC power is turned off. Using ▲/▼ buttons switches the standby mode setting between

NORMAL and SAVING.

NORMAL Ù SAVING

• When SAVING is selected and the projector is in the standby state, the power consumption is lowered with some functional restrictions as below.

- The RS-232C communication control is disabled except turning the projector on and changing the STANDBY MODE setting.

- The STANDBY of the MONITOR OUT (

below) is invalid, and no



signal is output from the MONITOR OUT port.

- The AUDIO OUT STANDBY of the AUDIO SOURCE ( invalid, and no signal is output from the AUDIO OUT ports (



39) is



5).

While the image signal from the input port chosen in step (1) is projected, the image signal from the input port selected in step (2) is output to MONITOR OUT port. (1) Choose a picture input port using

▲/▼ buttons.

Choose STANDBY to select the picture output in the standby mode.

(2) Select the output signal from the

MONITOR OUT port using ◄/►

buttons.

Select OFF to disable the MONITOR

OUT port for the input port or standby

mode chosen in the step (1).

• If you have changed the setting of STANDBY, it applies only to the current standby mode, NORMAL or SAVING, selected under STANDBY MODE, without changing the setting of the other mode. The factory settings are as follows:

- COMPUTER IN for the NORMAL mode of STANDBY MODE

- OFF for the SAVING mode of STANDBY MODE

Page 48

AUDIO menu

From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table.

Item Description

VOLUME

SPEAKER

AUDIO SOURCE

HDMI AUDIO

Using the ◄/► buttons adjusts the volume.

Low Ù High

Using the ▲/▼ buttons turns on/off the built-in speaker.

ON Ù OFF

When OFF is selected, the built-in speaker does not work. While the image signal from the input port chosen in step (1) is

projected, the audio signal from the input port selected in step (2) is output to both the AUDIO OUT port and built-in speaker of this projector. However, the built-in speaker does not work when SPEAKER is set to OFF.

(1) Choose a picture input port using

the ▲/▼ buttons.

Choose AUDIO OUT STANDBY to select the sound output in the standby mode.

(2) Select one of the AUDIO IN ports

using ◄/► buttons.

Select

mode chosen in the step (1).

• In the AUDIO SOURCE window, “H” symbolizes the audio signal from the HDMI port. It can be selected only for the picture input from the HDMI port.

• C.C. (Closed Caption) is automatically activated when and an input signal containing C.C. is received. This function is available only when the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPUTER IN, and when AUTO is selected for DISPLAY in the C.C. menu under the SCREEN menu (

• AUDIO OUT STANDBY is automatically set to OFF when SAVING is selected for the STANDBY MODE item in the SETUP menu.

Using the ▲/▼ buttons switches the mode for the HDMI audio. Check each of the two modes provided and select the suitable one for your HDMI audio device.

1 Ù 2

to mute the sound from the input port or in the standby

AUDIO menu

is selected

45).



Page 49

SCREEN menu

From the SCREEN menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ▲/▼/◄/► buttons switches the OSD (On Screen Display) language.

LANGUAGE

MENU POSITION

BLANK

START UP

(continued on next page)

ENGLISH Ù FRANÇAIS Ù DEUTSCH Ù ESPAÑOL

(shown in the LANGUAGE dialog)

Press the ENTER or INPUT button to save the language setting. Using the ▲/▼/◄/► buttons adjusts the menu position.

To quit the operation, press the MENU button on the remote control or keep no operation for about 10 seconds.

Using the ▲/▼ buttons switches the mode for the blank screen. The blank screen is a screen for the temporarily blanking feature (22). It is displayed by pressing the BLANK button on the remote control.

MyScreen Ù ORIGINAL Ù BLUE Ù WHITE Ù BLACK

MyScreen : ORIGINAL : Screen preset as the standard screen. BLUE, WHITE, BLACK : Plain screens in each color.

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the plain black screen after several minutes.

Using the ▲/▼ buttons switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected.

MyScreen Ù ORIGINAL Ù OFF

MyScreen : ORIGINAL : Screen preset as the standard screen. OFF : Plain black screen.

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the BLANK screen ( minutes. If also the BLANK screen is the MyScreen or ORIGINAL, the plain black screen is instead used.

• When the ON is selected to the MyScreen PASSWORD item in the SECURITY menu (

Screen can be registered by the MyScreen item (41).

52), the START UP is fixed to MyScreen.



22) after several



Page 50

Item Description

This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.

1. Selecting this item displays a dialog

2. Using the ▲/▼/◄/► buttons adjusts

MyScreen

• This function cannot be selected when the ON is selected to the MyScreen Lock item (

• This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu (

• This function is unavailable for a signal from the HDMI port.

(continued on next page)

SCREEN menu

titled “MyScreen”. It will ask you if you start capturing an image from

the current screen. Please wait for the target image to be displayed, and press the ENTER or INPUT button when the image is displayed. The image will freeze and the frame for capturing will appear. To stop performing, press the RESET button on the remote control.

the frame position.

Please move the frame to the position

of the image which you want to use. The

frame may not be able to be moved for

some input signals.

To start registration, press the ENTER

or INPUT button on the remote control. To restore the screen and return to the previous dialog, press the RESET button on the remote control. Registration takes several minutes. When the registration is completed, the registered screen and the following message is displayed for several seconds:

“MyScreen registration is nished.”

If the registration failed, the following message is displayed:

“A capturing error has occurred. Please try again.”

42).



52).



Page 51

SCREEN menu

Item Description

Using the ▲/▼ buttons turns on/off the MyScreen lock function.

MyScreen Lock

When the ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen.

• This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu (

Using the ▲/▼ buttons turns on/off the message function.

When the ON is selected, the following message function works.

MESSAGE

• When the OFF is selected, please remember if the picture is frozen. Do not mistake freezing for a malfunction (

(continued on next page)

ON Ù OFF

52).



ON Ù OFF

“AUTO IN PROGRESS” while automatically adjusting “NO INPUT IS DETECTED” “SYNC IS OUT OF RANGE” “INVALID SCAN FREQ.” “NOT AVAILABLE” “Searching….” while searching for the input “Detecting….” while an input signal is detected “AUTO ECO MODE” while starting up with AUTO ECO MODE The indication of the input signal displayed by changing The indication of the aspect ratio displayed by changing The indication of the PICTURE MODE displayed by changing The indication of the MY MEMORY displayed by changing The indication of “FREEZE” and “II” while freezing the screen by pressing the FREEZE button. The indication of the TEMPLATE displayed by changing.

22).



Page 52

Item Description

Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE

(2) Use the ▲/▼ buttons on the SOURCE

(3) Select an icon you'd like to assign to the

(4) Select a number you'd like to assign for

(5) If you'd like to modify the name assigned

SOURCE NAME

(6) The current name will be displayed on

(7)

(8) To nish entering text, move the cursor to the OK on screen and

(continued on next page)

SCREEN menu

NAME and press the ► or ENTER button. The SOURCE NAME menu will be displayed.

NAME menu to select the port to be named and press the ► button. The SOURCE NAME dialog will be displayed. Right side of the menu is blank until a name is specied.

port in the SOURCE NAME dialog. The name assigned to the port will also be automatically switched according to your icon selection. Press the ► or ENTER button to determine your icon selection.

the port along with the icon. You can select the number either from blank (no number assigned), 1, 2, 3, or 4.

to the port, select CUSTOM NAME and press the ► button.

the rst line. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button or press the ◄ and INPUT button at the same time. Also if you move the cursor to DELETE or ALL CLEAR on screen and press the ENTER or INPUT button, 1 character or all characters will be erased. The name can be a maximum of 16 characters.

To change an already inserted character, press the ▲ button to move the cursor to the rst line, and use the ◄/► buttons to move the cursor on the character to be changed.

After pressing the ENTER or INPUT button, the character is selected. Then, follow the same procedure as described at the item (6) above.

press the ►, ENTER or INPUT button. To revert to the previous name without saving changes, move the cursor to the CANCEL on screen and press the ◄, ENTER or INPUT button.

Page 53

SCREEN menu

Item Description

Using the ▲/▼ buttons switches the mode for the template screen. Press the ► button to display the selected template, and press the ◄ button to close the displayed screen. The last selected template is displayed when the MY BUTTON allocated to the TEMPLATE function is pressed (

TEMPLATE

You can turn a map upside down and scroll it horizontally when MAP1 or MAP2 is selected. To invert or scroll the map, display the guidance by pressing the RESET button on the remote control three seconds or more when MAP1 or MAP2 appears. While the guidance is displayed:

• Press the ▲ cursor button and then press the ENTER or INPUT button to place the Northern Hemisphere on the top.

• Press the ▼ cursor button and then press the ENTER or INPUT button to place the Southern Hemisphere on the top.

• Press the ◄/► cursor button and then press the ENTER or INPUT button to scroll the map horizontally.

(continued on next page)

48).



TEST PATTERN Ù DOT-LINE1 Ù DOT-LINE2 Ù DOT-LINE3

MAP2 Ù MAP1 Ù CIRCLE2 Ù CIRCLE1 Ù DOT-LINE4

Page 54

Item Description

The C.C. is the function that displays a transcript or dialog of the audio portion of a video, les or other presentation or other relevant sounds. It is required to have NTSC format video or 480i@60 format component video source supporting C.C. feature to utilize this function. It may not work properly, depending on equipment or signal source. In this case, please turn off the Closed Caption.

DISPLAY

Select Closed Caption DISPLAY setting from following options using ▲/▼ buttons.

AUTO Ù ON Ù OFF

AUTO : Closed Caption automatically displays when the volume

is muted. ON : Closed Caption is on. OFF : Closed Caption is off.

• The caption is not displayed when the OSD menu is active.

• The Closed Caption is the function to display the dialogue, narration, and / or sound effects of a television program or other

C.C.

(Closed Caption)

video sources. The Closed Caption availability is depending upon broadcaster and/or content.

MODE

Select Closed Caption MODE setting from following options using ▲/▼ buttons.

CAPTIONS Ù TEXT CAPTIONS : Display Closed Caption.

TEXT : Display Text data, which is for additional information such

as news reports or a TV program guide. The information covers the entire screen. Not all of the C.C. program has Text information.

CHANNEL

Select Closed Caption CHANNEL from following options using ▲/▼ buttons.

1 Ù 2 Ù 3 Ù 4

SCREEN menu

1: Channel 1, primary channel / language 2: Channel 2 3: Channel 3 4: Channel 4

The channel data may vary, depending on the content. Some channel might be used for secondary language or empty.

Page 55

OPTION menu

From the OPTION menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table.

Item Description

Using the ▲/▼ buttons turns on/off the automatic signal search function.

ON Ù OFF

AUTO SEARCH

AUTO

KEYSTONE

DIRECT POWER

(continued on next page)

When the ON is selected, detecting no signal automatically cycles through input ports in the following order. The search is started from the current port. Then when an input is found, the projector will stop searching and display the image.

COMPUTER IN Ö HDMI VIDEO

Using the ▲/▼ buttons turns on/off the automatic keystone function.

ON Ù OFF ON : Automatic keystone distortion correction will be executed

whenever changing the slant of the projector.

OFF : This function is disabled. Please execute the AUTO

KEYSTONE in the SETUP menu for automatic keystone distortion correction.

• When the projector is suspended from the ceiling this feature will not function properly so select the OFF.

• This function will be unavailable when the Transition Detector is on

(54)

Using the ▲/▼ buttons turns on/off the DIRECT POWER ON function.

ON Ù OFF

When set to the ON, the lamp in projector will be automatically turned on without the usual procedure ( projector is supplied with the power after the power was cut while the lamp was on.

• This function does not work as long as the power has been supplied to the projector while the lamp is off.

•

After turning the lamp on by the DIRECT POWER ON function, if neither input nor operation is detected for about 30 minutes, the projector is turned off, even though the AUTO POWER OFF function

(

47) is disabled.



S-VIDEO



13), only when the



Page 56

Item Description

Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off.

Long (max. 99 minutes) Ù Short (min. 0 minute = DISABLE)

OPTION menu

AUTO POWER

OFF

LAMP TIME

FILTER TIME

(continued on next page)

When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with nosignal or an unsuitable signal reaches at the set time, the projector lamp will be turned off. If one of the projector's buttons or the remote control buttons is pressed or one of the commands (except get commands) is transmitted to the CONTROL port during the corresponding time, projector will not be turned off. Please refer to the section “Turning off the power”

The lamp time is the usage time of the lamp, counted after the last resetting. It is shown in the OPTION menu. Pressing the RESET button on the remote control or the ► button of the projector displays a dialog.

To reset the lamp time, select the OK using the ► button.

• Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.

• For the lamp replacement, see the section "Replacing the lamp"

(



The lter time is the usage time of the air lter, counted after the last resetting. It is shown in the OPTION menu. Pressing the RESET button on the remote control or the ► button of the projector displays a dialog.

To reset the lter time, select the OK using the ► button.

• the air lter, for a suitable indication about the air lter.

• For the air lter cleaning, see the section “Cleaning and replacing the air lter” (

(13).



59, 60).

CANCEL

57, 58).

CANCEL

Please reset the lter time only when you have cleaned or replaced

Page 57

OPTION menu

Item Description

You can use this item to assign one of the following functions to the BLANK button on the control panel ( buttons on the remote control (

(1) Choose a button to assign a function from BLANK, MY

(2) Then using the ▲/▼/◄/► buttons sets one of the following

• COMPUTER IN: Sets port to COMPUTER IN.

• HDMI: Selects input from HDMI port.

• S-VIDEO: Sets port to S-VIDEO.

• VIDEO: Sets port to VIDEO.

• INFORMATION: Displays the INPUT_INFORMATION (

• AUTO KEYSTONE : Performs automatic keystone distortion

• MY MEMORY: Loads one of adjustment data stored (

MY BUTTON

• PICTURE MODE: Changes the PICTURE MODE (

• FILTER RESET: Displays the lter time reset conrmation dialogue

• TEMPLATE: Makes the template pattern selected to the

• AV MUTE: Turns the picture and audio on/off.

• RESOLUTION: Turns on/off the RESOLUTION dialog. (

• ECO MODE: Turns on/off the ECO MODE dialog. (

• BLANK: Turns on/off the blank function. (BLANK only)

• FREEZE: Turns on/off the freeze function. (BLANK only)

• VOLUME: Turns on/off the volume dialog. (BLANK only)

• AUTO: Using ▲/▼ buttons selects the picture input port to be selected with

pressing the MY SOURCE/DOC.CAMERA button on the remote

MY SOURCE

control. Select the picture input that is connected with a document camera.

(continued on next page)

5) and the MY BUTTON 1/2



6).



BUTTON-1 and MY BUTTON-2. Use the ▲/▼ buttons to select the desired button on the menu and press the ► button.

functions to the chosen button. Press the ENTER or INPUT button to save the setting.

50) or



the SYSTEM_INFORMATION or nothing.

correction (



37).



29). When more than one data are saved, the adjustment changes every time the MY BUTTON is pressed. When no data is saved in memory, the dialog "No saved data" appears. When the current adjustment is not saved to memory, the dialog as shown in the right appears. If you want to keep the current adjustment, please press the ► button to exit. Otherwise loading a data will overwrite the current adjusted condition.

25).



(

47).



TEMPLATE item(

44) appear or disappear.



38)



36)

Performs the automatic adjustment function. (BLANK only)

COMPUTER IN Ù HDMI VIDEO Ù S-VIDEO

Page 58

Item Description

Selecting this item displays the SERVICE menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button on the remote control to execute the item.

FAN SPEED

Using the ▲/▼ buttons switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc. Note that the projector is noisier when the HIGH is selected.

AUTO ADJUST

Using the ▲/▼ buttons to select one of the mode. When the DISABLE is selected, the automatic adjustment feature is disabled.

• projector, environment around the projector, etc., the automatic adjustment

SERVICE

may not work correctly. In such a case, please choose DISABLE to disable the automatic adjustment, and make adjustment manually.

GHOST

1. Select a color element of ghost using

2. Adjust the selected element using the

FILTER MESSAGE

Use the ▲/▼ button to set the timer for notifying by the message when to replace the lter unit

After choosing an item except OFF, the message “REMINDER

***HRS PASSED .....” will appear after the timer reaches the interval

time set by this feature ( When the OFF is chosen, the message will not appear. Utilize this feature to keep the air lter clean, setting the suitable time according to your environment of this projector.

• air lter becomes to be blocked by dust or other matter, the internal temperature will rise, which could cause malfunction, or reduce the lifetime of the projector.

• Please be careful with the operating environment of the projector and the condition of the lter unit.

(continued on next page)

OPTION menu

HIGH Ù NORMAL

FINE Ù FAST Ù DISABLE

FINE: Finer tuning including H.SIZE adjustment. FAST: Faster tuning, setting H.SIZE to prearranged data for the

input signal.

Depending on conditions, such as input image, signal cable to the

the ◄/► buttons.

▲/▼ buttons to disappear ghost.

100h Ù 200h Ù 500h Ù 1000h Ù 2000h Ù 3000h Ù 4000h Ù 5000h Ù OFF

62).



Please take care of the lter unit periodically, even if there is no message. If the

Page 59

OPTION menu

Item Description

KEY LOCK

Using the ▲/▼ buttons turns on/off the key lock feature. When ON is selected, the buttons on the projector except the STANDBY/ON button are locked.

ON Ù OFF

• Please use this function to prevent tampering or accidental operation. This function does not have any effect on the remote control.

INFORMATION

Selecting this item displays a dialog titled “INPUT_INFORMATION”. It shows the information about the current input.

SERVICE

(continued)

• The “FRAME LOCK” message on the dialog means the frame lock function is working.

• This item can't be selected for no signal and sync out.

• When the MY TEXT DISPLAY is set to ON, the MY TEXT is displayed together with the input information in the INPUT_ INFORMATION box (



56).

FACTORY RESET

Selecting OK usingthe ► button performs this function. By this function, all the items in all of menus will collectively return to the initial setting. Note that the LAMP TIME, FILTER TIME, LANGUAGE, FILTER MESSAGE, SECURITY settings, and others are not reset.

CANCEL

Page 60

SECURITY menu

This projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed. To use SECURITY menu: User registration is required before using the security functions.

Enter the SECURITY menu

1. Use the ▲/▼ buttons on the SECURITY menu to select ENTER PASSWORD and press the ► button. The ENTER PASSWORD box will be displayed.

2. Use the ▲/▼/◄/► buttons to enter the registered password. The factory default password is 4610. This password can be changed ( PASSWORD box and press the ► button to display the SECURITY menu.

• It is strongly recommended the factory default password to be changed as soon as possible.

• If an incorrect password is input, the ENTER PASSWORD box will be displayed again. If incorrect password is input 3 times, the projector will turn off. Afterwards the projector will turn off every time an incorrect password is input.

3. Items shown in the table below can be performed.

If you have forgotten your password

(1). While the ENTER PASSWORD box is displayed, press and hold

the RESET button on the remote control for about 3 seconds or press and hold the INPUT button for 3 seconds while pressing the ► button on the projector.

(2). The 10 digit Inquiring Code will be displayed. Contact your dealer

with the 10 digit Inquiring Code. Your password will be sent after your user registration information is conrmed.

• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will close. If necessary, repeat the process from (1).

below). Move the cursor to the right side of the ENTER



Item Description

(1) Use the ▲/▼ buttons on the SECURITY menu

(2) Use the ▲/▼/◄/► buttons to enter the new password. (3) Move the cursor to the right side of the

SECURITY

PASSWORD

CHANGE

(4)

• Please do not forget your password.

(continued on next page)

to select SECURITY PASSWORD CHANGE and press the ► button to display the ENTER NEW PASSWORD box.

ENTER NEW PASSWORD box and press the ► button to display the NEW PASSWORD AGAIN box, enter the same password again. Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button and the NOTE NEW PASSWORD box will be displayed for about 30 seconds, please

make note of the password during this time. Pressing the ENTER button on the remote control or ► button on the projector will close the NOTE NEW PASSWORD box.

Page 61

SECURITY menu

Item Description

The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.

1 Turning on the MyScreen PASSWORD

1-1 Use the ▲/▼ buttons on the SECURITY menu to

1-2 Use the ▲/▼ buttons on the MyScreen

1-3 Use the ▲/▼/◄/► buttons to enter the

1-4 Move the cursor to the right side of the

MyScreen

PASSWORD

(continued on next page)

When a password is set for MyScreen:

•

unavailable). Turning the MyScreen PASSWORD off will allow normal operation of these functions.

•

2 Turning off the MyScreen PASSWORD

2-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off

2-2

If an incorrect PASSWORD is input, the menu will close. If necessary, repeat the process from 2-1.

3 If you have forgotten your password

3-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off

3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit

3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will

select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/ off menu.

PASSWORD on/off menu to select ON. The ENTER NEW PASSWORD box (small) will be displayed.

password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box, enter the same PASSWORD again.

NEW PASSWORD AGAIN box and press the ► button to display the NOTE NEW PASSWORD box for about 30 seconds, please make note of the password during this time. Pressing the ENTER button on the remote control or ► button on the projector will return to MyScreen PASSWORD on/off menu.

The MyScreen registration function (and menu) will be unavailable. The MyScreen Lock menu will be unavailable. The START UP setting will be locked on MyScreen (and the menu will be

Please do not forget your MyScreen PASSWORD.

menu. Select OFF to display the ENTER PASSWORD box (large). Enter the registered password and the screen will return to the MyScreen PASSWORD on/off menu.

menu.

Inquiring Code will be displayed inside the box.

be sent after your user registration information is conrmed.

ENTER NEW PASSWORD

box (small)

ENTER PASSWORD box

(large)

Page 62

Item Description

PIN LOCK is a function which prevents the projector from being used unless a registered Code is input.

1 Turning on the PIN LOCK

1-1 Use the ▲/▼ buttons on the SECURITY menu

1-2 Use the ▲/▼ buttons on the PIN LOCK on/

1-3 Input a 4 part PIN code using the ▲/▼/◄/►,

Afterwards, anytime the projector is restarted after AC power is turned off the Enter PIN Code box will be displayed. Enter the registered PIN code. The projector can be used after entering the registered PIN code. If an incorrect PIN code is input, the Enter PIN code box will be displayed again.

PIN LOCK

If an incorrect PIN Code is input 3 times, the projector will turn off. Afterwards the projector will turn off every time an incorrect PIN code is input. The projector will also turn off if there is no key input for about 5 minutes while the Enter PIN code box is displayed. This function will activate only when the projector is started after AC power is turned off.

•

2 Turning off the PIN LOCK

2-1 Follow the procedure in 1-1 to display the PIN LOCK on/off menu. 2-2 Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be

If an incorrect PIN Code is input 3 times, the menu will close.

3 If you have forgotten your PIN Code

3-1 While the Enter PIN Code box is displayed, press and hold the RESET

3-2 Contact your dealer with the 10 digit Inquiring Code. Your PIN Code will

(continued on next page)

SECURITY menu

to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/ off menu.

off menu to select ON and the Enter PIN Code box will be displayed.

COMPUTER or INPUT button. The PIN Code again box will appear. Reenter the same PIN code. This will complete the PIN code registration.

If there is no key input for about 55 seconds

•

while the Enter PIN Code box or the PIN Code again box is displayed,

the menu will close. If necessary, repeat the process from 1-1.

Please do not forget your PIN code.

displayed. Enter the registered PIN code to turn the PIN LOCK function off.

button for three seconds or press and hold the INPUT button for 3 seconds while pressing the ► button on the projector. The 10 digit Inquiring Code will be displayed.

If there is no key input for about 5 minutes

•

while the Inquiring Code is displayed, the

projector will turn off.

be sent after your user registration information is conrmed.

Page 63

SECURITY menu

Item Description

If this function is set to ON when the vertical angle of the projector or MIRROR setting at which the projector is turned on is different than the previously recorded, the TRANSITION DETECTOR ON alarm will be displayed and the projector will not display the input signal.

• To display the signal again, set this function OFF.

• After about 5 minutes of displaying the TRANSITION DETECTOR ON alarm, the lamp will turn off.

• Keystone adjustment feature has been prohibited as long as the Transition Detector function is on.

1 Turning on the TRANSITION DETECTOR

1-1 Use the ▲/▼ buttons on the SECURITY menu

1-2

1-3 Use the ▲/▼/◄/► buttons to enter a

TRANSITION

DETECTOR

1-4

• Please do not forget your TRANSITION DETECTOR password.

• This function will activate only when the projector is started after turning off the AC power.

• This feature may not function properly if the projector is not in a stable position when ON is selected.

2 Turning off the TRANSITION DETECTOR

2-1 2-2

If an incorrect password is input, the menu will close. If necessary, repeat the process from 2-1.

3 If you have forgotten your password

3-1 3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit

3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will

(continued on next page)

to select TRANSITION DETECTOR and press the ► or the ENTER button to display the TRANSITION DETECTOR on/off menu. Use the ▲/▼ buttons on the TRANSITION DETECTOR on/off menu to select ON. Select ON and the current angle and MIRROR setting will be recorded. The ENTER NEW PASSWORD box (small) will be displayed.

password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box, enter the same password again. Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button to display the NOTE NEW PASSWORD box for about 30 seconds, please make note

of the password during this time. Pressing the ENTER button on the remote control or the ► button on the projector will return to the TRANSITION DETECTOR on/off menu.

Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.

Select OFF to display the ENTER

PASSWORD box (large). Enter the registered

password and the screen will return to the

TRANSITION DETECTOR on/off menu.

Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.

Inquiring Code will be displayed inside the box.

be sent after your user registration information is conrmed.

ENTER NEW PASSWORD

box (small)

ENTER PASSWORD box

(large)

Page 64

Item Description

The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT;

• The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the DISPLAY setting.

• The MY TEXT WRITING menu will be unavailable, which can prevent the MY TEXT from being overwritten.

1 Turning on the MY TEXT PASSWORD

1-1 Use the ▲/▼ buttons on the SECURITY menu to

1-2 Use the ▲/▼ buttons on the MY TEXT

1-3 Use the ▲/▼/◄/► buttons to enter the

1-4 Move the cursor to the right side of the

MY TEXT

PASSWORD

Pressing the ENTER button on the remote control or ► button on the projector will return to the MY TEXT PASSWORD on/off menu.

2 Turning off the MY TEXT PASSWORD

2-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off

2-2 Select OFF to display the ENTER

If an incorrect password is input, the menu will close. If necessary, repeat the process from 2-1

3 If you have forgotten your password

3-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off

3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit

3-3 Contact your dealer with the 10 digit inquiring code. Your password will

(continued on next page)

SECURITY menu

select the MY TEXT PASSWORD and press the

► button to display the MY TEXT PASSWORD

on/off menu.

PASSWORD on/off menu to select ON. The

ENTER NEW PASSWORD box (small) will

be displayed.

ENTER NEW PASSWORD

password. Move the cursor to the right side

of the ENTER NEW PASSWORD box (small)

and press the ► button to display the NEW

PASSWORD AGAIN box, and then enter the

same password again.

NEW PASSWORD AGAIN box and press

► button to display the NOTE NEW

PASSWORD box for about 30 seconds,

then please make note of the password

during this time.

menu.

PASSWORD box (large). Enter the

registered password and the screen will

return to the MY TEXT PASSWORD on/off

menu.

inquiring code will be displayed inside the box.

be sent after your user registration information is conrmed.

box (small)

ENTER PASSWORD box

(large)

Page 65

SECURITY menu

Item Description

(1) Use the ▲/▼ buttons on the SECURITY menu to

select the MY TEXT DISPLAY and press the ► button to display the MY TEXT DISPLAY on/off menu.

(2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select

on or off.

MY TEXT DISPLAY

MY TEXT WRITING

ON Ù OFF

When it is set ON, the MY TEXT will be displayed on the START UP screen and the INPUT_ INFORMATION when the INFORMATION on the SERVICE menu is chosen.

• This function is available only when the MY TEXT PASSWORD function is set to the OFF.

(1) Use the ▲/▼ buttons on the

SECURITY menu to select the MY TEXT WRITING and press the ► button. The MY TEXT WRITING dialog will be displayed.

(2) The current MY TEXT will be displayed

on the rst 3 lines. If not yet written, the lines will be blank. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button or press the ◄ and INPUT button at the same time. Also if you move the cursor to DELETE or ALL CLEAR on screen and press the ENTER or INPUT button, 1 character or all characters will be erased. The MY TEXT can be input up to 24 characters on each line.

(3) To change an already inserted

character, press the ▲/▼ button to move the cursor to one of the rst 3 lines, and use the ◄/► buttons to move the cursor on the character to be changed. After pressing the ENTER or INPUT button, the character is selected. Then, follow the same procedure as described at the item (2) above.

(4) To nish entering text, move the cursor to the OK on screen and press

the ►, ENTER or INPUT button. To revert to the previous MY TEXT without saving changes, move the cursor to the CANCEL on screen and press the ◄, ENTER or INPUT button.

The MY TEXT WRITING function is available only when the MY TEXT

•

PASSWORD function is set to OFF.

Page 66

Maintenance

Replacing the lamp

A lamp has nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, make contact with your dealer and tell the lamp type number.

Type number : DT01141

Replacing the lamp

Turn the projector off, and unplug the power cord.

Allow the projector to cool for at least 45 minutes. Prepare a new lamp. If the projector is mounted on a

ceiling, or if the lamp has broken, also ask the dealer to replace the lamp.

In case of replacement by yourself, follow the following procedure.

Loosen the screw (marked by arrow) of the lamp

cover and then slide and lift the lamp cover to the side to remove it.

Loosen the 2 screws (marked by arrow) of the

lamp, and slowly pick up the lamp by the handle. Never loosen any other screws.

Insert the new lamp, and retighten rmly the

2 screws of the lamp that are loosened in the

previous process to lock it in place. While putting the interlocking parts of the lamp cover

and the projector together, slide the lamp cover back in place. Then rmly fasten the screw of the lamp cover.

Turn the projector on and reset the lamp time using

the LAMP TIME item in the OPTION menu.

(1) Press the MENU button to display a menu. (2) Point at the ADVANCED MENU in the menu using

the ▼/▲ button, then press the ► button.

(3) Point at the OPTION in the left column of the menu

using the ▼/▲ button, then press the ► button. Point at the LAMP TIME using the ▼/▲ button, then press the ► button. A dialog will appear.

(4) (5)

Press the ► button to select “OK” on the dialog. It performs resetting the lamp time.

CAUTION

is taken out.

►Do not touch any inner space of the projector, while the lamp

㧡

Lamp cover

Handle

㧠



NOTE

for a suitable indication about the lamp.

• Please reset the lamp time only when you have replaced the lamp,

Page 67

Maintenance

Replacing the lamp (continued)

Lamp warning

HIGH VOLTAGE

►

WARNING

The projector uses a high-pressure mercury glass lamp. The lamp

HIGH TEMPERATURE

can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, if the bulb bursts, it is possible for shards of glass to y into the lamp housing, and for gas containing mercury and dust containing ne particles of glass to escape from the projector’s vent holes. ►About disposal of a lamp: This product contains a mercury lamp; do not put it in a trash. Dispose of it in accordance with environmental laws.

• For lamp recycling, go to www.lamprecycle.org (in the US).

• For product disposal, consult your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, call your dealer.

•

Disconnect

the plug

from the

power

outlet

If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to inhale the gas or ne particles that come out from the projector's vent holes, and not to get them into your eyes or mouth.

• Before replacing the lamp, turn the projector off and unplug the power cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover while the projector is suspended from a ceiling. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

•

Use only the lamp of the specied type. Use of a lamp that does not meet the lamp

specications for this model could cause a re, damage or shorten the life of this product.

• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, consult your local dealer or a service representative.

•

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

HIGH PRESSURE

Page 68

Maintenance

Cleaning and replacing the air ﬁlter

The air lter unit of this projector consists of a lter cover, two kinds of lters, and a lter frame. The new double large lters system is expected to function longer. However, please check and clean it periodically to keep ventilation needed for normal operation of the projector. When the indicators or a message prompts you to clean the air lter, comply with it as soon as possible. Replace the lters when they are damaged or too soiled. To prepare new lters, make contact with your dealer and tell the following type number.

Type number : UX36761 (Filter set)

When you replace the lamp, please replace the air lter. An air lter of specied type will come together with a replacement lamp for this projector.

Turn the projector off, and unplug the power cord.

Allow the projector to sufciently cool down.

Use a vacuum cleaner on and around the lter cover.

Pick and pull up the lter cover knobs to take it off.

Use a vacuum cleaner for the lter vent of the

projector.

Take the ne meshed lter out while holding the

lter cover. It is recommended to leave the coarse meshed lter in the lter cover as it is.

Use a vacuum cleaner on both sides of the ne

meshed lter while holding it so it will not be sucked in. Use a vacuum cleaner for the inside of the lter cover to clean up the coarse meshed lter. If the lters are damaged or heavily soiled, replace them with new ones.

Put the ne meshed lter on the coarse meshed

one, turning its stitched side up.

Put the lter unit back into the projector.

(continued on next page)

Filter cover

Filter cover knobs

Intake vent

Filter (coarse meshed)

Filter (ne meshed)

Stitched side

Page 69

Maintenance

Cleaning and replacing the air lter (continued)

Turn the projector on and reset the lter time using the FILTER TIME item in

the EASY MENU. (1) Press the MENU button to display a menu. (2) Point at the FILTER TIME using the ▼/▲ button, then press the ► button.

A dialog will appear.

(3) Press the ► button to select “OK” on the dialog. It performs resetting the

lter time.

WARNING

is not plugged in, then allow the projector to cool sufciently. Taking care of the air lter in a high temperature state of the projector could cause an electric shock, a burn or malfunction to the projector. ►Use only the air lter of the specied type. Do not use the projector without the air lter or the lter cover. It could result in a re or malfunction to the projector. ►Clean the air lter periodically. If the air lter becomes clogged by dust or the like, internal temperatures rise and could cause a re, a burn or malfunction to the projector.

NOTE

• When you replace the projection lamp, please replace the air lter. An air lter of specied type will come together with a replacement lamp for this projector.

• Please reset the lter time only when you have cleaned or replaced the air lter, for a suitable indication about the air lter.

• The projector may display the message such as “CHECK THE AIR FLOW” or turn off the projector, to prevent the internal heat level rising.

• Please replace the air lter when it is damaged or too soiled.

►Before taking care of the air lter, make sure the power cable

Page 70

Maintenance

Other care

Inside of the projector

In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year.

Caring for the lens

If the lens is awed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of handling.

Turn the projector off, and unplug the power cord. Allow the projector to cool

sufciently. After making sure that the projector is cool adequately, lightly wipe the lens

with a commercially available lens-cleaning wipe. Do not touch the lens directly with your hand.

Caring for the cabinet and remote control

Incorrect care could have adverse inuence such as discoloration, peeling paint, etc.

Turn the projector off, and unplug the power cord. Allow the projector to cool

sufciently. After making sure that the projector is cool adequately, lightly wipe with gauze

or a soft cloth. If the projector is extremely dirty, dip soft cloth in water or a neutral cleaner diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.

WARNING

and then allow the projector to cool sufciently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. ►Never try to care for the inside of the projector personally. Doing is so dangerous. ►Avoid wetting the projector or inserting liquids in the projector. It could result in a re, an electric shock, and/or malfunction to the projector.

• Do not put anything containing water, cleaners or chemicals near the projector.

• Do not use aerosols or sprays.

CAUTION

following. Incorrect care could cause not only an injury but adverse inuence such as discoloration, peeling paint, etc.

►Do not use cleaners or chemicals other than those specied in this manual. ►Do not polish or wipe with hard objects.

►Before caring, make sure the power cord is not plugged in,

►Please take right care of the projector according to the

Page 71

Troubleshooting

If an abnormal operation should occur, stop using the projector immediately.

►

WARNING

Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact to your dealer or service company.

Otherwise if a problem occurs with the projector, the following checks and measures are recommended before requesting repair. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied.

Related messages

When some message appears, check and cope with it according to the following table. Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message Description

There is no input signal.

Please conrm the signal input connection, and the status of the signal source.

The horizontal or vertical frequency of the input signal is

not within the specied range.

Please conrm the specs for your projector or the signal source specs.

An improper signal is input.

Please conrm the specs for your projector or the signal source specs.

The internal temperature is rising.

Please turn the power off, and allow the projector to cool down at least 20 minutes. After having conrmed the following items, please turn the power ON again.

• Is there blockage of the air passage aperture?

• Is the air lter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the remedy, please set FAN SPEED of the SERVICE item in the OPTION menu to HIGH.

A note of precaution when cleaning the air lter.

Please immediately turn the power off, and clean or change the air lter referring to the “Cleaning and replacing the air lter” section of this manual. After you have cleaned or changed the air lter, please be sure to reset the lter timer

(

47).



The button operation is not available (



6).

Page 72

Troubleshooting

Regarding the indicator lamps

When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table.

POWER

indicator

Lighting

In Orange

Blinking

In Green

Lighting

In Green

Blinking

In Orange

Blinking

In Red

Blinking

In Red

Lighting

In Red

Blinking

In Red

Lighting

In Red

Blinking

Red

Lighting

In Red

(Continued on next page)

LAMP

indicator

Turned

off

Turned

off

Turned

off

Turned

off

(discretionary)

Lighting

In Red

Blinking

In Red

Turned

off

TEMP

indicator

Turned

off

Turned

off

Turned

off

Turned

off

(discretionary)

Turned

off

Turned

off

Blinking

In Red

Description

The projector is in a standby state.

Please refer to the section “Power on/off”.

The projector is warming up.

Please wait.

The projector is in an on state.

Ordinary operations may be performed.

The projector is cooling down.

Please wait.

The projector is cooling down. A certain error has been detected.

Please wait until POWER indicator nishes blinking, and then perform the proper measure using the item descriptions below.

The lamp does not light, and there is a possibility that interior portion has become heated.

Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufciently cooled down, please make conrmation of the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air lter dirty?

•

Does the peripheral temperature exceed 35°C? If the same indication is displayed after the remedy, please change the lamp referring to the section “Replacing the lamp”.

The lamp cover has not been properly xed.

Please turn the power off, and allow the projector to cool down at least 45 minutes. After the projector has sufciently cooled down, please make conrmation of the attachment state of the lamp cover. After performing any needed maintenance, turn the power on again. If the same indication is displayed after the remedy, please contact your dealer or service company.

The cooling fan is not operating.

Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufciently cooled down, please make conrmation that no foreign matter has become caught in the fan, etc., and then turn the power on again. If the same indication is displayed after the remedy, please contact your dealer or service company.

Page 73

Troubleshooting

Regarding the indicator lamps (continued)

POWER

indicator

LAMP

indicator

TEMP

indicator

Description

There is a possibility that the interior portion has become heated.

Blinking

In Red

Lighting

In Red

Turned

off

Lighting

In Red

• Is there blockage of the air passage aperture?

• Is the air lter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the remedy, please set FAN SPEED of SERVICE item in OPTION menu to HIGH

(49)

It is time to clean the air lter.

Lighting

In Green

Simultaneous

blinking in Red

Please immediately turn the power off, and clean or change the air lter referring to the section “Cleaning and replacing the air lter”. After cleaning or changing the air lter, please be sure to reset the lter timer. After the remedy, reset the power to ON.

There is a possibility that the interior portion

Lighting

In Green

NOTE

Alternative

blinking in Red

•

When the interior portion has become overheated, for safety

has become overcooled.

Please use the unit within the usage temperature parameters (5°C to 35°C). After the treatment, reset the power to ON.

purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufciently cooled down, please make conrmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

Resetting all settings

When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu (50) can reset all settings(except LANGUAGE, FILTER TIME, LAMP TIME, FILTER MESSAGE and SECURITY settings and etc.) to the factory default.

Page 74

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects

About the phenomenon confused with a machine defect, check and cope with it according to the following table.

Phenomenon Cases not involving a machine defect

The electrical power cord is not plugged in.

Correctly connect the power cord.

The main power source has been interrupted during operation such as by a power outage (blackout), etc.

Please disconnect the power plug from the power outlet,

Power does not

come on.

and allow the projector to cool down at least 10 minutes, then turn the power on again.

Either there is no lamp and/or lamp cover, or either

of these has not been properly xed.

Please turn the power off and disconnect the power plug from the power outlet, and allow the projector to cool down at least 45 minutes. After the projector has sufciently cooled down, please make conrmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

The signal cables are not correctly connected.

Correctly connect the connection cables.

Signal source does not correctly work.

Correctly set up the signal source device by referring to the manual of the source device.

Neither sounds

nor pictures are

outputted.

The input changeover settings are mismatched.

Select the input signal, and correct the settings.

The BLANK function for pictures and the MUTE function for sounds are working.

AV MUTE may be active. Refer to the item “Sound does not come out” and “No

pictures are displayed” on the next page to turn off the MUTE and BLANK functions.

(Continued on next page)

Reference

page

11, 13

57, 58

–

15, 16

15, 22,

Page 75

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon Cases not involving a machine defect

The signal cables are not correctly connected.

Correctly connect the audio cables.

The MUTE function is working.

Restore the sound pressing the MUTE or VOLUME +/- button on the remote control.

The volume is adjusted to an extremely low level.

Sound does not

come out.

Adjust the volume to a higher level using the menu function or the remote control.

The AUDIO SOURCE/SPEAKER setting is not correct.

Correctly set the AUDIO SOURCE/SPEAKER in the AUDIO menu.

The mode selected for HDMI AUDIO is not suitable.

Check each of the two modes provided and select the suitable one for your HDMI audio device.

The lens cover is attached.

Remove the lens cover.

The signal cables are not correctly connected.

Correctly connect the connection cables.

The brightness is adjusted to an extremely low level.

No pictures are

displayed.

Adjust the BRIGHTNESS to a higher level using the menu function.

The computer cannot detect the projector as a plug and play monitor.

Make sure that the computer can detect a plug and play monitor using another plug and play monitor.

The BLANK screen is displayed.

Press the BLANK button on the control panel or the remote control.

Video screen

display freezes.

The FREEZE function is working. Press the FREEZE button to restore the screen to normal.

Color settings are not correctly adjusted.

Colors have a

faded- out

appearance, or

Color tone is

poor.

(Continued on next page)

Perform picture adjustments by changing the COLOR TEMP, COLOR, TINT and/or COLOR SPACE settings, using the menu functions.

The COLOR SPACE setting is not suitable.

Change the COLOR SPACE setting to the AUTO, RGB, SMPTE240, REC709 or REC601.

Reference

page

28, 33

Page 76

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon Cases not involving a machine defect

The brightness and/or contrast are adjusted to an

extremely low level.

Adjust the BRIGHTNESS and/or CONTRAST settings to a higher level using the menu function.

Pictures appear

dark.

The ECO MODE function is working.

Select the NORMAL for the ECO MODE item in the SETUP menu.

The lamp is approaching the end of its product lifetime.

Replace the lamp.

Either the focus and/or horizontal phase settings are not properly adjusted.

Pictures appear

blurry.

Adjust the focus using the focus ring, and/or the H PHASE using the menu function.

The lens is dirty or misty.

Clean the lens referring to the section “Caring for the lens”.

No signal is

output from the

MONITOR OUT

and AUDIO

OUT ports.

RS-232C does

not work.

The SAVING function is working in the standby state.

Select the NORMAL for the STANDBY MODE item in the SETUP menu.

When the projector is operating in Eco mode,

ickering may appear on screen.

Some kind

of image

degradation

such as

ickering or stripes appear on the screen.

Set ECO MODE to NORMAL, and set AUTO ECO MODE to OFF, in the SETUP menu.

The OVER SCAN ratio is too big.

Adjust OVER SCAN in the IMAGE menu smaller.

Excessive VIDEO NR.

Change the setting of VIDEO NR in the INPUT menu.

The FRAME LOCK function cannot work on the current input signal.

Set FRAME LOCK in the INPUT menu to OFF.

(Continued on next page)

Reference

page

57, 58

18, 32

37, 38

Page 77

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

NOTE

• Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and it does not constitute or imply a machine defect.

• The projector may make a rattling sound when tilted, moved or shaken, since a ap to control the air ow inside of the projector has moved. Be aware that this is not a failure or malfunction.

Page 78

Specications

Speciﬁcations

Item Specication

Product name Liquid crystal projector Liquid Crystal Panel 1,024,000 pixels (1280 horizontal x 800 vertical) Lamp 200 W UHB Speaker 1 W Power supply AC 100-120 V/2.9 A, AC 220-240 V/1.4 A Power consumption AC 100-120 V/290 W, AC 220-240 V/270 W Temperature range 5 ~ 35 °C (Operating)

Size

Weight (mass) approx. 2.2 kg

Ports

Optional parts

306 (W) x 77 (H) x 221 (D) mm * Not including protruding parts. Please refer to the following gure.

Computer input port

COMPUTER IN ..................................D-sub 15 pin mini x1

Computer output port

MONITOR OUT ..................................D-sub 15 pin mini x1

HDMI input port

HDMI ....................................................HDMI connector x1

Video input port

S-VIDEO ...................................................mini DIN 4 pin x1

VIDEO ..................................................................... RCA x1

Audio input/output port

AUDIO IN1 .....................................................Stereo mini x1

AUDIO IN2 .....................................................Stereo mini x1

AUDIO OUT ..................................................Stereo mini x1

Others

CONTROL .................................................... D-sub 9 pin x1

Lamp: DT01141 Filter set: UX36761 Mounting accessary

Laser remote control: RC-R008

* For more information, please consult your dealer.

: HAS-X1 (Bracket for ceiling mount)

HAS-204L (Fixing adaptor for low ceilings) HAS-304H (

Fixing adaptor for high ceilings

Speciﬁcations

)

Page 79

Speciﬁcations

Specications (continued)

221

306

[unit: mm]

Page 80

Projector

CPWX8

User's Manual (detailed) Operating Guide – Technical

Example of PC signal

Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode

720 x 400 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.9 72.8 VESA VGA (72Hz) 640 x 480 37.5 75.0 VESA VGA (75Hz) 640 x 480 43.3 85.0 VESA VGA (85Hz) 800 x 600 35.2 56.3 VESA SVGA (56Hz) 800 x 600 37.9 60.3 VESA SVGA (60Hz) 800 x 600 48.1 72.2 VESA SVGA (72Hz) 800 x 600 46.9 75.0 VESA SVGA (75Hz) 800 x 600 53.7 85.1 VESA SVGA (85Hz)

832 x 624 49.7 74.5 Mac 16” mode 1024 x 768 48.4 60.0 VESA XGA (60Hz) 1024 x 768 56.5 70.1 VESA XGA (70Hz) 1024 x 768 60.0 75.0 VESA XGA (75Hz) 1024 x 768 68.7 85.0 VESA XGA (85Hz) 1152 x 864 67.5 75.0 VESA 1280 x 768 47.7 60.0 VESA W-XGA (60Hz) 1280 x 800 49.7 60.0 VESA 1280 x 960 60.0 60.0 VESA

1280 x 1024 64.0 60.0 VESA SXGA (60Hz) 1280 x 1024 80.0 75.0 VESA SXGA (75Hz) 1280 x 1024 91.1 85.0 VESA SXGA (85Hz) 1680 x 1050 65.3 60.0 VESA WSXGA+ (60Hz)

1440 x 900 55.9 59.9 VESA WXGA+ (60Hz)

1600 x 1200 75.0 60.0 VESA UXGA (60Hz)

37.9 85.0 VESA TEXT

1152 x 864 (75Hz)

1280 x 800 (60Hz) 1280 x 960 (60Hz)

NOTE • Be sure to check jack type, signal level, timing and resolution

before connecting this projector to a PC.

• Some PCs may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

• Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above.

• Although the projector can display signals with resolution up to UXGA (1600x1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical.

• Automatic adjustment may not function correctly with some input signals.

• The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G.

Page 81

Initial set signals

The following signals are used for the initial settings. The signal timing of some PC models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu.

Back porch (B) Front porch (D) Back porch (b) Front porch (d)

Data Data H. Sync. V. Sync.

Sync (A) Sync (a)

Resolution

(H x V)

720 x 400 640 x 480 3.8 1.9 25.4 0.6 2 33 480 10 VGA (60Hz) 640 x 480 1.3 4.1 20.3 0.8 3 28 480 9 VGA (72Hz) 640 x 480 2.0 3.8 20.3 0.5 3 16 480 1 VGA (75Hz) 640 x 480 1.6 2.2 17.8 1.6 3 25 480 1 VGA (85Hz) 800 x 600 2.0 3.6 22.2 0.7 2 22 600 1 SVGA (56Hz) 800 x 600 3.2 2.2 20.0 1.0 4 23 600 1 SVGA (60Hz) 800 x 600 2.4 1.3 16.0 1.1 6 23 600 37 SVGA (72Hz) 800 x 600 1.6 3.2 16.2 0.3 3 21 600 1 SVGA (75Hz) 800 x 600 1.1 2.7 14.2 0.6 3 27 600 1 SVGA (85Hz)

832 x 624 1.1 3.9 14.5 0.6 3 39 624 1 Mac 16" mode 1024 x 768 2.1 2.5 15.8 0.4 6 29 768 3 XGA (60Hz) 1024 x 768 1.8 1.9 13.7 0.3 6 29 768 3 XGA (70Hz) 1024 x 768 1.2 2.2 13.0 0.2 3 28 768 1 XGA (75Hz) 1024 x 768 1.0 2.2 10.8 0.5 3 36 768 1 XGA (85Hz)

1152 x 864 1.2 2.4 10.7 0.6 3 32 864 1 1152 x 864 (75Hz) 1280 x 768 1.7 2.5 16.0 0.8 3 23 768 1 W-XGA (60Hz) 1280 x 800 1.6 2.4 15.3 0.8 3 24 800 1 W-XGA (60Hz) 1280 x 960 1.0 2.9 11.9 0.9 3 36 960 1 W-XGA (60Hz)

1280 x 1024 1.0 2.3 11.9 0.4 3 38 1024 1 SXGA (60Hz) 1280 x 1024 1.1 1.8 9.5 0.1 3 38 1024 1 SXGA (75Hz) 1280 x 1024 1.0 1.4 8.1 0.4 3 44 1024 1 SXGA (85Hz) 1680 x 1050 1.2 1.9 11.5 0.7 6 30 1050 3 WSXGA+ (60Hz)

1440 x 900 1.4 2.2 13.5 0.8 6 25 900 3 WXGA+ (60Hz)

1600 x 1200 1.2 1.9 9.9 0.4 3 46 1200 1 UXGA (60Hz)

Active video (C)

Horizontal signal timing (μs) Vertical signal timing (lines)

(A) (B) (C) (D) (a) (b) (c) (d)

2.0 3.0 20.3 1.0 3 42 400 1 TEXT

Active video (c)

Signal mode

Page 82

Connection to the ports





 

Connection to the ports

NOTICE

►Use the cables with straight plugs, not L-shaped ones, as the

input ports of the projector are recessed.

COMPUTER IN, BMONITOR OUT

D-sub 15pin mini shrink jack <Computer signal>

• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)

• H/V. sync. signal: TTL level (positive/negative)

• Composite sync. signal: TTL level <Component video signal>

• Video signal:

-Y, Analog, 1.0±0.1Vp-p with composite sync, 75Ω terminated

-Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated

-C

r/Pr

, Analog, 0.7±0.1Vp-p 75Ω terminated

System: 480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60, 1080i@50/60, 1080p@50/60

Pin Signal Pin Signal

Video Red, Cr/Pr

(No connection)

2 Video Green, Y 10 Ground

3 Video Blue, Cb/Pb 11 (No connection)

4 (No connection)

5 Ground

: SDA (DDC data), (No connection)

: (No connection)

6 Ground Red, Ground Cr/Pr 13 H. sync / Composite sync., (No connection)

7 Ground Green, Ground Y 14 V. sync., (No connection)

8 Ground Blue, Ground Cb/Pb

: SCL (DDC clock), (No connection)

: (No connection)

Page 83

Connection to the ports (continued)

19 17 15 13 11 9 7 5 3 1

18 16 14 12 10 8 6 4 2

C E

S-VIDEO

Mini DIN 4pin jack

• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL (60Hz) Pin Signal

Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator

Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator

2 Brightness signal, 1.0Vp-p, 75Ω terminator

3 Ground

4 Ground

VIDEO

RCA jack

• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL (60Hz)

• 1.0±0.1Vp-p, 75Ω terminator

HDMI

• Type :Digital audio/video connector

• Audio signal : Linear PCM (Sampling rate; 32/44.1/48 kHz)

Pin Signal Pin Signal Pin Signal

1 T.M.D.S. Data2 + 8 T.M.D.S. Data0 Shield 15 SCL 2 T.M.D.S. Data2 Shield 9 T.M.D.S. Data0 - 16 SDA 3 T.M.D.S. Data2 - 10 T.M.D.S. Clock + 17 DDC/CEC Ground 4 T.M.D.S. Data1 + 11 T.M.D.S. Clock Shield 5 T.M.D.S. Data1 Shield 12 T.M.D.S. Clock - 19 Hot Plug Detect 6 T.M.D.S. Data1 - 13 CEC 7 T.M.D.S. Data0 + 14 Reserved(N.C. on device)

+5V Power

Page 84

Connection to the ports (continued)

AUDIO IN1, GAUDIO IN2

Ø3.5 stereo mini jack

• 200 mVrms 47kΩ terminator

AUDIO OUT

Ø3.5 stereo mini jack

• 200 mVrms 1kΩ output impedance

Page 85

Connection to the ports (continued)

CONTROL

D-sub 9pin plug

• About the details of RS-232C communication,

54321

987

please refer to the following page.

Pin Signal Pin Signal Pin Signal

1 (No connection) 4 (No connection) 7RTS 2 RD 5 Ground 8 CTS 3 TD 6 (No connection) 9 (No connection)

Page 86

Connection to the ports (continued)

To input component video signal to COMPUTER IN ports

ex.

D-sub plug

Y CB/PB C R/PR

COMPONENT VIDEO OUT

VCR/DVD/Blu-ray

Disc player

RCA plugs

RCA connectors

To input component video signal to the COMPUTER IN port of the projector, use a RCA to D-sub cable or adapter. For about the pin description of the required cable or adapter, refer to the descriptions about COMPUTER IN port (3).

Page 87

RS-232C Communication

When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer.

For details of RS-232C commands, refer to RS-232C Communication command

10).

table (

Connection

Turn off the projector and the computer.

Connect the projector's CONTROL port and the computer's RS-232C port

with a RS-232C cable (cross). Use the cable that ful lls the speci cation shown in  gure.

Turn the computer on, and after the computer has started up turn the projector

on.

RS-232C

RS-232C Cable

(cross)

CONTROL

RS-232C port

of the computer



CD (1) (1) RD(2) (2) RD TD (3) (3) TD DTR (4) (4) GND (5) (5) GND DSR (6) (6)

RTS (7) (7) RTS

DTS (8) (8) CTS

RI (9) (9)

CONTROL port

of the projector

987

54321

−

Page 88

Communication settings

1. Protocol

19200bps,8N1

RS-232C Communication (continued)

2. Command format

Byte Number

Command

Action

<SET>

Change setting to desired value [(cL)(cH)] by [(eL)(eH)].

<GET>

Read projector internal setup value [(bL) (bH)] .

<INCREMENT> Increment setup value [(bL)(bH)] by 1.

<DECREMENT> Decrement setup value [(bL)(bH)] by 1.

<EXECUTE> Run a command [(bL)(bH)].

("h" shows hexadecimal)

01 2 3456

Header Data

Header

code

L H L H L H L H L H L H

BEh EFh 03h 06h 00h

Packet

Data

size

CRC

ag

(aL) (aH) 01h 00h (bL) (bH) (cL) (cH)

(aL) (aH) 02h 00h (bL) (bH) 00h 00h

(aL) (aH) 04h 00h (bL) (bH) 00h 00h

(aL) (aH) 05h 00h (bL) (bH) 00h 00h

(aL) (aH) 06h 00h (bL) (bH) 00h 00h

789101112

Action Type

[Header code], [Packet], [Data size]

Set [BEh, EFh, 03h, 06h, 00h] to byte number 0

[CRC ag]

For byte number

5, 6,

refer to

RS-232C Communication command table

[Action]

Set functional code to byte number 7, 8.

<SET> = [01h, 00h], <GET> = [02h, 00h], <INCREMENT> =[04h, 00h] <DECREMENT> = [05h, 00h], <EXECUTE> = [06h, 00h] Refer

the

command table above.

[Type], [Setting code]

For byte number

9〜12

, refer to

RS-232C Communication command table

Setting

code

Page 89

RS-232C Communication command table

Names Operation Type Header

Power Set Turn off BE EF 03 06 00 2A D3 01 00 00 60 00 00

Turn on BE EF 03 06 00 BA D2 01 00 00 60 01 00

Get BE EF 03 06 00 19 D3 02 00 00 60 00 00

[Example return]

00 00 01 00 02 00

[Off] [On] [Cool down]

Input Source Set COMPUTER IN BE EF 03 06 00 FE D2 01 00 00 20 00 00

HDMI BE EF 03 06 00 0E D2 01 00 00 20 03 00

S-VIDEO BE EF 03 06 00 9E D3 01 00 00 20 02 00

VIDEO BE EF 03 06 00 6E D3 01 00 00 20 01 00

Get BE EF 03 06 00 CD D2 02 00 00 20 00 00

Error Status Get BE EF 03 06 00 D9 D8 02 00 20 60 00 00

[Example return]

00 00 01 00 02 00 03 00

[Normal] [Cover error] [Fan error] [Lamp error]

04 00 05 00 07 00 08 00

 >7HPSHUURU@ >$LUÀRZHUURU@ >&ROGHUURU@ >)LOWHUHUURU@

MAGNIFY Get BE EF 03 06 00 7C D2 02 00 07 30 00 00

Increment BE EF 03 06 00 1A D2 04 00 07 30 00 00

Decrement BE EF 03 06 00 CB D3 05 00 07 30 00 00

FREEZE Set NORMAL BE EF 03 06 00 83 D2 01 00 02 30 00 00

FREEZE BE EF 03 06 00 13 D3 01 00 02 30 01 00

Get BE EF 03 06 00 B0 D2 02 00 02 30 00 00

PICTURE MODE Set NORMAL BE EF 03 06 00 23 F6 01 00 BA 30 00 00

CINEMA BE EF 03 06 00 B3 F7 01 00 BA 30 01 00

DYNAMIC BE EF 03 06 00 E3 F4 01 00 BA 30 04 00

BOARD(BLACK) BE EF 03 06 00 E3 EF 01 00 BA 30 20 00

BOARD(GREEN) BE EF 03 06 00 73 EE 01 00 BA 30 21 00

WHITEBOARD BE EF 03 06 00 83 EE 01 00 BA 30 22 00

DAYTIME BE EF 03 06 00 E3 C7 01 00 BA 30 40 00 Get BE EF 03 06 00 10 F6 02 00 BA 30 00 00

[Example return]

00 00 01 00 04 00 10 00

[Normal] [Cinema] [Dynamic] [Custom]

20 00 21 00 22 00 40 00

[BOARD(BLACK)] [BOARD(GREEN)] [WHITEBOARD] [DAY TIME]

BRIGHTNESS Get BE EF 03 06 00 89 D2 02 00 03 20 00 00

Increment BE EF 03 06 00 EF D2 04 00 03 20 00 00

Decrement BE EF 03 06 00 3E D3 05 00 03 20 00 00

BRIGHTNESS Reset Execute BE EF 03 06 00 58 D3 06 00 00 70 00 00

CONTRAST Get BE EF 03 06 00 FD D3 02 00 04 20 00 00

Increment BE EF 03 06 00 9B D3 04 00 04 20 00 00

Decrement BE EF 03 06 00 4A D2 05 00 04 20 00 00

CONTRAST Reset Execute BE EF 03 06 00 A4 D2 06 00 01 70 00 00

CRC Action Type Setting Code

Command Data

(continued on next page)

Page 90

RS-232C Communication command table (continued)

Names Operation Type Header

GAMMA Set DEFAULT-1 BE EF 03 06 00 07 E9 01 00 A1 30 20 00

User Gamma Pattern Set Off BE EF 03 06 00 FB FA 01 00 80 30 00 00

User Gamma Point 1 Get BE EF 03 06 00 08 FE 02 00 90 30 00 00

User Gamma Point 1 Reset

User Gamma Point 2 Get BE EF 03 06 00 F4 FF 02 00 91 30 00 00

User Gamma Point 2 Reset

User Gamma Point 3 Get BE EF 03 06 00 B0 FF 02 00 92 30 00 00

User Gamma Point 3 Reset

User Gamma Point 4 Get BE EF 03 06 00 4C FE 02 00 93 30 00 00

User Gamma Point 4 Reset

User Gamma Point 5 Get BE EF 03 06 00 38 FF 02 00 94 30 00 00

User Gamma Point 5 Reset

User Gamma Point 6 Get BE EF 03 06 00 C4 FE 02 00 95 30 00 00

User Gamma Point 6 Reset

User Gamma Point 7 Get BE EF 03 06 00 80 FE 02 00 96 30 00 00

User Gamma Point 7 Reset

CUSTOM-1 BE EF 03 06 00 07 FD 01 00 A1 30 10 00 DEFAULT-2 BE EF 03 06 00 97 E8 01 00 A1 30 21 00 CUSTOM-2 BE EF 03 06 00 97 FC 01 00 A1 30 11 00 DEFAULT-3 BE EF 03 06 00 67 E8 01 00 A1 30 22 00 CUSTOM-3 BE EF 03 06 00 67 FC 01 00 A1 30 12 00 DEFAULT-4 BE EF 03 06 00 F7 E9 01 00 A1 30 23 00 CUSTOM-4 BE EF 03 06 00 F7 FD 01 00 A1 30 13 00 DEFAULT-5 BE EF 03 06 00 C7 EB 01 00 A1 30 24 00 CUSTOM-5 BE EF 03 06 00 C7 FF 01 00 A1 30 14 00 DEFAULT-6 BE EF 03 06 00 57 EA 01 00 A1 30 25 00 CUSTOM-6 BE EF 03 06 00 57 FE 01 00 A1 30 15 00

Get BE EF 03 06 00 F4 F0 02 00 A1 30 00 00

9 steps gray scale BE EF 03 06 00 6B FB 01 00 80 30 01 00

15 steps gray scale BE EF 03 06 00 9B FB 01 00 80 30 02 00

Ramp BE EF 03 06 00 0B FA 01 00 80 30 03 00

Get BE EF 03 06 00 C8 FA 02 00 80 30 00 00

Increment BE EF 03 06 00 6E FE 04 00 90 30 00 00

Decrement BE EF 03 06 00 BF FF 05 00 90 30 00 00

Execute BE EF 03 06 00 58 C2 06 00 50 70 00 00

Increment BE EF 03 06 00 92 FF 04 00 91 30 00 00

Decrement BE EF 03 06 00 43 FE 05 00 91 30 00 00

Execute BE EF 03 06 00 A4 C3 06 00 51 70 00 00

Increment BE EF 03 06 00 D6 FF 04 00 92 30 00 00

Decrement BE EF 03 06 00 07 FE 05 00 92 30 00 00

Execute BE EF 03 06 00 E0 C3 06 00 52 70 00 00

Increment BE EF 03 06 00 2A FE 04 00 93 30 00 00

Decrement BE EF 03 06 00 FB FF 05 00 93 30 00 00

Execute BE EF 03 06 00 1C C2 06 00 53 70 00 00

Increment BE EF 03 06 00 5E FF 04 00 94 30 00 00

Decrement BE EF 03 06 00 8F FE 05 00 94 30 00 00

Execute BE EF 03 06 00 68 C3 06 00 54 70 00 00

Increment BE EF 03 06 00 A2 FE 04 00 95 30 00 00

Decrement BE EF 03 06 00 73 FF 05 00 95 30 00 00

Execute BE EF 03 06 00 94 C2 06 00 55 70 00 00

Increment BE EF 03 06 00 E6 FE 04 00 96 30 00 00

Decrement BE EF 03 06 00 37 FF 05 00 96 30 00 00

Execute BE EF 03 06 00 D0 C2 06 00 56 70 00 00

CRC Action Type Setting Code

Command Data

(continued on next page)

Page 91

RS-232C Communication command table (continued)

Names Operation Type Header

User Gamma Point 8 Get

User Gamma Point 8 Reset

COLOR TEMP Set 1 HIGH

COLOR TEMP GAIN R

Reset

COLOR TEMP GAIN G

Reset

COLOR TEMP GAIN B

Reset

COLOR TEMP

OFFSET R

COLOR TEMP

OFFSET R Reset

COLOR TEMP

OFFSET G

COLOR TEMP

OFFSET G Reset

COLOR TEMP

OFFSET B

COLOR TEMP

OFFSET B Reset

Increment

Decrement

Execute

1 CUSTOM

2 MID

2 CUSTOM

3 LOW

3 CUSTOM

4 Hi-BRIGHT-1

4 CUSTOM

5 Hi-BRIGHT-2

5 CUSTOM

6 Hi-BRIGHT-3

6 CUSTOM

Get BE EF 03 06 00 C8 F5 02 00 B0 30 00 00 Get BE EF 03 06 00 34 F4 02 00 B1 30 00 00

Increment BE EF 03 06 00 52 F4 04 00 B1 30 00 00

Decrement BE EF 03 06 00 83 F5 05 00 B1 30 00 00

Execute BE EF 03 06 00 10 C6 06 00 46 70 00 00

Get BE EF 03 06 00 70 F4 02 00 B2 30 00 00

Increment BE EF 03 06 00 16 F4 04 00 B2 30 00 00

Decrement BE EF 03 06 00 C7 F5 05 00 B2 30 00 00

Execute BE EF 03 06 00 EC C7 06 00 47 70 00 00

Get BE EF 03 06 00 8C F5 02 00 B3 30 00 00

Increment BE EF 03 06 00 EA F5 04 00 B3 30 00 00

Decrement BE EF 03 06 00 3B F4 05 00 B3 30 00 00

Execute BE EF 03 06 00 F8 C4 06 00 48 70 00 00

Get BE EF 03 06 00 04 F5 02 00 B5 30 00 00

Increment BE EF 03 06 00 62 F5 04 00 B5 30 00 00

Decrement BE EF 03 06 00 B3 F4 05 00 B5 30 00 00

Execute BE EF 03 06 00 40 C5 06 00 4A 70 00 00

Get BE EF 03 06 00 40 F5 02 00 B6 30 00 00

Increment BE EF 03 06 00 26 F5 04 00 B6 30 00 00

Decrement BE EF 03 06 00 F7 F4 05 00 B6 30 00 00

Execute BE EF 03 06 00 BC C4 06 00 4B 70 00 00

Get BE EF 03 06 00 BC F4 02 00 B7 30 00 00

Increment BE EF 03 06 00 DA F4 04 00 B7 30 00 00

Decrement BE EF 03 06 00 0B F5 05 00 B7 30 00 00

Execute BE EF 03 06 00 C8 C5 06 00 4C 70 00 00

CRC Action Type Setting Code

Command Data

BE EF 03 06 00 7C FF 02 00 97 30 00 00 BE EF 03 06 00 1A FF 04 00 97 30 00 00 BE EF 03 06 00 CB FE 05 00 97 30 00 00 BE EF 03 06 00 2C C3 06 00 57 70 00 00 BE EF 03 06 00 0B F5 01 00 B0 30 03 00 BE EF 03 06 00 CB F8 01 00 B0 30 13 00 BE EF 03 06 00 9B F4 01 00 B0 30 02 00 BE EF 03 06 00 5B F9 01 00 B0 30 12 00 BE EF 03 06 00 6B F4 01 00 B0 30 01 00 BE EF 03 06 00 AB F9 01 00 B0 30 11 00 BE EF 03 06 00 3B F2 01 00 B0 30 08 00 BE EF 03 06 00 FB FF 01 00 B0 30 18 00 BE EF 03 06 00 AB F3 01 00 B0 30 09 00 BE EF 03 06 00 6B FE 01 00 B0 30 19 00 BE EF 03 06 00 5B F3 01 00 B0 30 0A 00 BE EF 03 06 00 9B FE 01 00 B0 30 1A 00

(continued on next page)

Page 92

RS-232C Communication command table (continued)

Names Operation Type Header

COLOR Get BE EF 03 06 00 B5 72 02 00 02 22 00 00

Increment BE EF 03 06 00 D3 72 04 00 02 22 00 00

Decrement BE EF 03 06 00 02 73 05 00 02 22 00 00

COLOR Reset Execute BE EF 03 06 00 80 D0 06 00 0A 70 00 00

TINT Get BE EF 03 06 00 49 73 02 00 03 22 00 00

Increment BE EF 03 06 00 2F 73 04 00 03 22 00 00

Decrement BE EF 03 06 00 FE 72 05 00 03 22 00 00

TINT Reset Execute BE EF 03 06 00 7C D1 06 00 0B 70 00 00

SHARPNESS Get BE EF 03 06 00 F1 72 02 00 01 22 00 00

Increment BE EF 03 06 00 97 72 04 00 01 22 00 00

Decrement BE EF 03 06 00 46 73 05 00 01 22 00 00

SHARPNESS Reset Execute BE EF 03 06 00 C4 D0 06 00 09 70 00 00

MY MEMORY Load Set 1 BE EF 03 06 00 0E D7 01 00 14 20 00 00

2 BE EF 03 06 00 9E D6 01 00 14 20 01 00 3 BE EF 03 06 00 6E D6 01 00 14 20 02 00 4 BE EF 03 06 00 FE D7 01 00 14 20 03 00

MY MEMORY Save Set 1 BE EF 03 06 00 F2 D6 01 00 15 20 00 00

2 BE EF 03 06 00 62 D7 01 00 15 20 01 00 3 BE EF 03 06 00 92 D7 01 00 15 20 02 00 4 BE EF 03 06 00 02 D6 01 00 15 20 03 00

ASPECT Set 4:3 BE EF 03 06 00 9E D0 01 00 08 20 00 00

16:9 BE EF 03 06 00 0E D1 01 00 08 20 01 00 14:9 BE EF 03 06 00 CE D6 01 00 08 20 09 00

16:10 BE EF 03 06 00 3E D6 01 00 08 20 0A 00

Native BE EF 03 06 00 5E D7 01 00 08 20 08 00 NORMAL BE EF 03 06 00 5E DD 01 00 08 20 10 00 Get BE EF 03 06 00 AD D0 02 00 08 20 00 00

OVER SCAN Get BE EF 03 06 00 91 70 02 00 09 22 00 00

Increment BE EF 03 06 00 F7 70 04 00 09 22 00 00

Decrement BE EF 03 06 00 26 71 05 00 09 22 00 00

OVER SCAN Reset Execute BE EF 03 06 00 EC D9 06 00 27 70 00 00

V POSITION Get BE EF 03 06 00 0D 83 02 00 00 21 00 00

Increment BE EF 03 06 00 6B 83 04 00 00 21 00 00

Decrement BE EF 03 06 00 BA 82 05 00 00 21 00 00

V POSITION Reset Execute BE EF 03 06 00 E0 D2 06 00 02 70 00 00

H POSITION Get BE EF 03 06 00 F1 82 02 00 01 21 00 00

Increment BE EF 03 06 00 97 82 04 00 01 21 00 00

Decrement BE EF 03 06 00 46 83 05 00 01 21 00 00

H POSITION Reset Execute BE EF 03 06 00 1C D3 06 00 03 70 00 00

H PHASE Get BE EF 03 06 00 49 83 02 00 03 21 00 00

Increment BE EF 03 06 00 2F 83 04 00 03 21 00 00

Decrement BE EF 03 06 00 FE 82 05 00 03 21 00 00

CRC Action Type Setting Code

Command Data

(continued on next page)

Page 93

RS-232C Communication command table (continued)

Names Operation Type Header

H SIZE Get BE EF 03 06 00 B5 82 02 00 02 21 00 00

H SIZE Reset Execute BE EF 03 06 00 68 D2 06 00 04 70 00 00

AUTO ADJUST

EXECUTE

PROGRESSIVE Set OFF BE EF 03 06 00 4A 72 01 00 07 22 00 00

VIDEO NR Set LOW BE EF 03 06 00 26 72 01 00 06 22 01 00

COLOR SPACE Set AUTO BE EF 03 06 00 0E 72 01 00 04 22 00 00

S-VIDEO FORMAT Set AUTO BE EF 03 06 00 E6 70 01 00 12 22 0A 00

C-VIDEO FORMAT Set AUTO BE EF 03 06 00 A2 70 01 00 11 22 0A 00

HDMI FORMAT Set AUTO BE EF 03 06 00 BA 77 01 00 13 22 00 00

HDMI RANGE Set AUTO BE EF 03 06 00 86 D8 01 00 22 20 00 00

COMPUTER IN Set AUTO BE EF 03 06 00 CE D6 01 00 10 20 03 00

Increment BE EF 03 06 00 D3 82 04 00 02 21 00 00

Decrement BE EF 03 06 00 02 83 05 00 02 21 00 00

Execute BE EF 03 06 00 91 D0 06 00 0A 20 00 00

TV BE EF 03 06 00 DA 73 01 00 07 22 01 00

FILM BE EF 03 06 00 2A 73 01 00 07 22 02 00

Get BE EF 03 06 00 79 72 02 00 07 22 00 00

MID BE EF 03 06 00 D6 72 01 00 06 22 02 00

HIGH BE EF 03 06 00 46 73 01 00 06 22 03 00

Get BE EF 03 06 00 85 73 02 00 06 22 00 00

RGB BE EF 03 06 00 9E 73 01 00 04 22 01 00

SMPTE240 BE EF 03 06 00 6E 73 01 00 04 22 02 00

REC709 BE EF 03 06 00 FE 72 01 00 04 22 03 00 REC601 BE EF 03 06 00 CE 70 01 00 04 22 04 00

Get BE EF 03 06 00 3D 72 02 00 04 22 00 00

NTSC BE EF 03 06 00 86 74 01 00 12 22 04 00

PAL BE EF 03 06 00 16 75 01 00 12 22 05 00

SECAM BE EF 03 06 00 16 70 01 00 12 22 09 00

NTSC4.43 BE EF 03 06 00 26 77 01 00 12 22 02 00

M-PAL BE EF 03 06 00 86 71 01 00 12 22 08 00 N-PAL BE EF 03 06 00 76 74 01 00 12 22 07 00

Get BE EF 03 06 00 75 76 02 00 12 22 00 00

NTSC BE EF 03 06 00 C2 74 01 00 11 22 04 00

PAL BE EF 03 06 00 52 75 01 00 11 22 05 00

SECAM BE EF 03 06 00 52 70 01 00 11 22 09 00

NTSC4.43 BE EF 03 06 00 62 77 01 00 11 22 02 00

M-PAL BE EF 03 06 00 C2 71 01 00 11 22 08 00 N-PAL BE EF 03 06 00 32 74 01 00 11 22 07 00

Get BE EF 03 06 00 31 76 02 00 11 22 00 00

VIDEO BE EF 03 06 00 2A 76 01 00 13 22 01 00

COMPUTER BE EF 03 06 00 DA 76 01 00 13 22 02 00

Get BE EF 03 06 00 89 77 02 00 13 22 00 00

NORMAL BE EF 03 06 00 16 D9 01 00 22 20 01 00

ENHANCED BE EF 03 06 00 E6 D9 01 00 22 20 02 00

Get BE EF 03 06 00 B5 D8 02 00 22 20 00 00

SYNC ON G OFF BE EF 03 06 00 5E D7 01 00 10 20 02 00

Get BE EF 03 06 00 0D D6 02 00 10 20 00 00

CRC Action Type Setting Code

Command Data

(continued on next page)

Page 94

RS-232C Communication command table (continued)

Names Operation Type Header

FRAME LOCK –

COMPUTER IN

FRAME LOCK –

HDMI

AUTO KEYSTONE V

EXECUTE

KEYSTONE V Get BE EF 03 06 00 B9 D3 02 00 07 20 00 00

KEYSTONE V Reset Execute BE EF 03 06 00 08 D0 06 00 0C 70 00 00

AUTO ECO MODE Set OFF BE EF 03 06 00 FB 27 01 00 10 33 00 00

ECO MODE Set NORMAL BE EF 03 06 00 3B 23 01 00 00 33 00 00

MIRROR Set NORMAL BE EF 03 06 00 C7 D2 01 00 01 30 00 00

STANDBY MODE Set NORMAL BE EF 03 06 00 D6 D2 01 00 01 60 00 00

MONITOR OUT -

COMPUTER IN

MONITOR OUT -

S-VIDEO

MONITOR OUT -

VIDEO

MONITOR OUT -

HDMI

MONITOR OUT -

STANDBY

VOLUME -

COMPUTER IN

Set OFF BE EF 03 06 00 3B C2 01 00 50 30 00 00

ON BE EF 03 06 00 AB C3 01 00 50 30 01 00

Get BE EF 03 06 00 08 C2 02 00 50 30 00 00

Set OFF BE EF 03 06 00 7F C2 01 00 53 30 00 00

ON BE EF 03 06 00 EF C3 01 00 53 30 01 00

Get BE EF 03 06 00 4C C2 02 00 53 30 00 00

Execute BE EF 03 06 00 E5 D1 06 00 0D 20 00 00

Increment BE EF 03 06 00 DF D3 04 00 07 20 00 00

Decrement BE EF 03 06 00 0E D2 05 00 07 20 00 00

ON BE EF 03 06 00 6B 26 01 00 10 33 01 00

Get BE EF 03 06 00 C8 27 02 00 10 33 00 00

ECO BE EF 03 06 00 AB 22 01 00 00 33 01 00

Get BE EF 03 06 00 08 23 02 00 00 33 00 00

H:INVERT BE EF 03 06 00 57 D3 01 00 01 30 01 00

V:INVERT BE EF 03 06 00 A7 D3 01 00 01 30 02 00

H&V:INVERT BE EF 03 06 00 37 D2 01 00 01 30 03 00

Get BE EF 03 06 00 F4 D2 02 00 01 30 00 00

SAVING BE EF 03 06 00 46 D3 01 00 01 60 01 00

Get BE EF 03 06 00 E5 D2 02 00 01 60 00 00

Set COMPUTER IN BE EF 03 06 00 3E F4 01 00 B0 20 00 00

OFF BE EF 03 06 00 CE B5 01 00 B0 20 FF 00

Get BE EF 03 06 00 0D F4 02 00 B0 20 00 00

Set COMPUTER IN BE EF 03 06 00 86 F5 01 00 B2 20 00 00

OFF BE EF 03 06 00 76 B4 01 00 B2 20 FF 00

Get BE EF 03 06 00 B5 F5 02 00 B2 20 00 00

Set COMPUTER IN BE EF 03 06 00 C2 F5 01 00 B1 20 00 00

OFF BE EF 03 06 00 32 B4 01 00 B1 20 FF 00

Get BE EF 03 06 00 F1 F5 02 00 B1 20 00 00

Set COMPUTER IN BE EF 03 06 00 7A F4 01 00 B3 20 00 00

OFF BE EF 03 06 00 8A B5 01 00 B3 20 FF 00

Get BE EF 03 06 00 49 F4 02 00 B3 20 00 00

Set COMPUTER IN BE EF 03 06 00 2A F7 01 00 BF 20 00 00

OFF BE EF 03 06 00 DA B6 01 00 BF 20 FF 00 Get BE EF 03 06 00 19 F7 02 00 BF 20 00 00 Get BE EF 03 06 00 CD CC 02 00 60 20 00 00

Increment BE EF 03 06 00 AB CC 04 00 60 20 00 00

Decrement BE EF 03 06 00 7A CD 05 00 60 20 00 00

CRC Action Type Setting Code

Command Data

(continued on next page)

Page 95

RS-232C Communication command table (continued)

Names Operation Type Header

VOLUME - S-VIDEO Get BE EF 03 06 00 75 CD 02 00 62 20 00 00

VOLUME - VIDEO Get BE EF 03 06 00 31 CD 02 00 61 20 00 00

VOLUME - HDMI Get BE EF 03 06 00 89 CC 02 00 63 20 00 00

VOLUME -

AUDIO OUT STANDBY

MUTE Set OFF BE EF 03 06 00 46 D3 01 00 02 20 00 00

SPEAKER Set ON BE EF 03 06 00 FE D4 01 00 1C 20 01 00

AUDIO SOURCE -

COMPUTER IN

AUDIO SOURCE -

HDMI

AUDIO SOURCE -

S-VIDEO

AUDIO SOURCE -

VIDEO

AUDIO OUT STANDBY Set AUDIO IN1 BE EF 03 06 00 7A DF 01 00 3F 20 01 00

HDMI AUDIO Set 1 BE EF 03 06 00 AE C6 01 00 40 20 01 00

Increment BE EF 03 06 00 13 CD 04 00 62 20 00 00

Decrement BE EF 03 06 00 C2 CC 05 00 62 20 00 00

Increment BE EF 03 06 00 57 CD 04 00 61 20 00 00

Decrement BE EF 03 06 00 86 CC 05 00 61 20 00 00

Increment BE EF 03 06 00 EF CC 04 00 63 20 00 00

Decrement BE EF 03 06 00 3E CD 05 00 63 20 00 00

Get BE EF 03 06 00 D9 CF 02 00 6F 20 00 00

Increment BE EF 03 06 00 BF CF 04 00 6F 20 00 00

Decrement BE EF 03 06 00 6E CE 05 00 6F 20 00 00

ON BE EF 03 06 00 D6 D2 01 00 02 20 01 00

Get BE EF 03 06 00 75 D3 02 00 02 20 00 00

OFF BE EF 03 06 00 6E D5 01 00 1C 20 00 00

Get BE EF 03 06 00 5D D5 02 00 1C 20 00 00

Set AUDIO IN1 BE EF 03 06 00 6E DC 01 00 30 20 01 00

AUDIO IN2 BE EF 03 06 00 9E DC 01 00 30 20 02 00

OFF BE EF 03 06 00 FE DD 01 00 30 20 00 00

Get BE EF 03 06 00 CD DD 02 00 30 20 00 00

Set OFF BE EF 03 06 00 BA DD 01 00 33 20 00 00

AUDIO IN1 BE EF 03 06 00 2A DC 01 00 33 20 01 00 AUDIO IN2 BE EF 03 06 00 DA DC 01 00 33 20 02 00

AUDIO_HDMI BE EF 03 06 00 7A C4 01 00 33 20 20 00

Get BE EF 03 06 00 89 DD 02 00 33 20 00 00

Set AUDIO IN1 BE EF 03 06 00 D6 DD 01 00 32 20 01 00

AUDIO IN2 BE EF 03 06 00 26 DD 01 00 32 20 02 00

OFF BE EF 03 06 00 46 DC 01 00 32 20 00 00

Get BE EF 03 06 00 75 DC 02 00 32 20 00 00

Set AUDIO IN1 BE EF 03 06 00 92 DD 01 00 31 20 01 00

AUDIO IN2 BE EF 03 06 00 62 DD 01 00 31 20 02 00

OFF BE EF 03 06 00 02 DC 01 00 31 20 00 00

Get BE EF 03 06 00 31 DC 02 00 31 20 00 00

AUDIO IN2 BE EF 03 06 00 8A DF 01 00 3F 20 02 00

OFF BE EF 03 06 00 EA DE 01 00 3F 20 00 00

Get BE EF 03 06 00 D9 DE 02 00 3F 20 00 00

2 BE EF 03 06 00 5E C6 01 00 40 20 02 00

Get BE EF 03 06 00 0D C7 02 00 40 20 00 00

CRC Action Type Setting Code

Command Data

(continued on next page)

Page 96

RS-232C Communication command table (continued)

Names Operation Type Header

LANGUAGE * Set ENGLISH BE EF 03 06 00 F7 D3 01 00 05 30 00 00

MENU POSITION H Get BE EF 03 06 00 04 D7 02 00 15 30 00 00

MENU POSITION H

Reset

MENU POSITION V Get BE EF 03 06 00 40 D7 02 00 16 30 00 00

MENU POSITION V

Reset

BLANK Set MyScreen BE EF 03 06 00 FB CA 01 00 00 30 20 00

FRANÇAIS BE EF 03 06 00 67 D2 01 00 05 30 01 00

DEUTSCH BE EF 03 06 00 97 D2 01 00 05 30 02 00

ESPAÑOL BE EF 03 06 00 07 D3 01 00 05 30 03 00 ITALIANO BE EF 03 06 00 37 D1 01 00 05 30 04 00

NORSK BE EF 03 06 00 A7 D0 01 00 05 30 05 00

NEDERLANDS BE EF 03 06 00 57 D0 01 00 05 30 06 00

PORTUGUÊS BE EF 03 06 00 C7 D1 01 00 05 30 07 00

SVENSKA BE EF 03 06 00 C7 D4 01 00 05 30 0B 00

3ɍ&&.ɂɃ BE EF 03 06 00 F7 D6 01 00 05 30 0C 00

SUOMI BE EF 03 06 00 67 D7 01 00 05 30 0D 00

POLSKI BE EF 03 06 00 97 D7 01 00 05 30 0E 00

TÜRKÇE BE EF 03 06 00 07 D6 01 00 05 30 0F 00

DANSK BE EF 03 06 00 A7 DF 01 00 05 30 11 00

ý(6.< BE EF 03 06 00 57 DF 01 00 05 30 12 00 MAGYAR BE EF 03 06 00 C7 DE 01 00 05 30 13 00 520Æ1Ă BE EF 03 06 00 F7 DC 01 00 05 30 14 00

SLOVENSKI BE EF 03 06 00 67 DD 01 00 05 30 15 00

HRVATSKI BE EF 03 06 00 97 DD 01 00 05 30 16 00

ǼȁȁǾȃǿȀǹ BE EF 03 06 00 07 DC 01 00 05 30 17 00

/,(789,Ǐ BE EF 03 06 00 F7 D9 01 00 05 30 18 00

EESTI BE EF 03 06 00 67 D8 01 00 05 30 19 00

LATVIEŠU BE EF 03 06 00 97 D8 01 00 05 30 1A 00

ไทย

ﺍﻝﻝﻍﺓ ﺍﻝﻉﺭﺏﯼﺓ

ﻑﺍﺭﺱﻯ

PORTUGUÊS BRA BE EF 03 06 00 57 DA 01 00 05 30 1E 00

Get BE EF 03 06 00 C4 D3 02 00 05 30 00 00

Increment BE EF 03 06 00 62 D7 04 00 15 30 00 00

Decrement BE EF 03 06 00 B3 D6 05 00 15 30 00 00

Execute BE EF 03 06 00 DC C6 06 00 43 70 00 00

Increment BE EF 03 06 00 26 D7 04 00 16 30 00 00

Decrement BE EF 03 06 00 F7 D6 05 00 16 30 00 00

Execute BE EF 03 06 00 A8 C7 06 00 44 70 00 00

ORIGINAL BE EF 03 06 00 FB E2 01 00 00 30 40 00

BLUE BE EF 03 06 00 CB D3 01 00 00 30 03 00 WHITE BE EF 03 06 00 6B D0 01 00 00 30 05 00 BLACK BE EF 03 06 00 9B D0 01 00 00 30 06 00

Get BE EF 03 06 00 08 D3 02 00 00 30 00 00

BE EF 03 06 00 37 D4 01 00 05 30 08 00 BE EF 03 06 00 A7 D5 01 00 05 30 09 00 BE EF 03 06 00 37 DE 01 00 05 30 10 00 BE EF 03 06 00 57 D5 01 00 05 30 0A 00

BE EF 03 06 00 07 D9 01 00 05 30 1B 00 BE EF 03 06 00 37 DB 01 00 05 30 1C 00 BE EF 03 06 00 A7 DA 01 00 05 30 1D 00

CRC Action Type Setting Code

Command Data

* Not all of the languages in the table are supported.

(continued on next page)

Page 97

RS-232C Communication command table (continued)

Names Operation Type Header

BLANK On/Off Set OFF BE EF 03 06 00 FB D8 01 00 20 30 00 00

ON BE EF 03 06 00 6B D9 01 00 20 30 01 00

Get BE EF 03 06 00 C8 D8 02 00 20 30 00 00

START UP Set MyScreen BE EF 03 06 00 CB CB 01 00 04 30 20 00

ORIGINAL BE EF 03 06 00 0B D2 01 00 04 30 00 00

OFF BE EF 03 06 00 9B D3 01 00 04 30 01 00

Get BE EF 03 06 00 38 D2 02 00 04 30 00 00

MyScreen Lock Set OFF BE EF 03 06 00 3B EF 01 00 C0 30 00 00

ON BE EF 03 06 00 AB EE 01 00 C0 30 01 00

Get BE EF 03 06 00 08 EF 02 00 C0 30 00 00

MESSAGE Set OFF BE EF 03 06 00 8F D6 01 00 17 30 00 00

ON BE EF 03 06 00 1F D7 01 00 17 30 01 00

Get BE EF 03 06 00 BC D6 02 00 17 30 00 00

TEMPLATE Set TEST PATTERN BE EF 03 06 00 43 D9 01 00 22 30 00 00

DOT-LINE1 BE EF 03 06 00 D3 D8 01 00 22 30 01 00 DOT-LINE2 BE EF 03 06 00 23 D8 01 00 22 30 02 00 DOT-LINE3 BE EF 03 06 00 B3 D9 01 00 22 30 03 00 DOT-LINE4 BE EF 03 06 00 83 DB 01 00 22 30 04 00

CIRCLE 1 BE EF 03 06 00 13 DA 01 00 22 30 05 00 CIRCLE 2 BE EF 03 06 00 E3 DA 01 00 22 30 06 00

MAP 1 BE EF 03 06 00 83 D4 01 00 22 30 10 00 MAP 2 BE EF 03 06 00 13 D5 01 00 22 30 11 00

Get BE EF 03 06 00 70 D9 02 00 22 30 00 00

TEMPLATE On/Off Set OFF BE EF 03 06 00 BF D8 01 00 23 30 00 00

ON BE EF 03 06 00 2F D9 01 00 23 30 01 00

Get BE EF 03 06 00 8C D8 02 00 23 30 00 00

C. C. - DISPLAY Set OFF BE EF 03 06 00 FA 62 01 00 00 37 00 00

ON BE EF 03 06 00 6A 63 01 00 00 37 01 00

AUTO BE EF 03 06 00 9A 63 01 00 00 37 02 00

Get BE EF 03 06 00 C9 62 02 00 00 37 00 00

C. C. - MODE Set CAPTIONS BE EF 03 06 00 06 63 01 00 01 37 00 00

TEXT BE EF 03 06 00 96 62 01 00 01 37 01 00

Get BE EF 03 06 00 35 63 02 00 01 37 00 00

C. C. - CHANNEL Set 1 BE EF 03 06 00 D2 62 01 00 02 37 01 00

2 BE EF 03 06 00 22 62 01 00 02 37 02 00 3 BE EF 03 06 00 B2 63 01 00 02 37 03 00 4 BE EF 03 06 00 82 61 01 00 02 37 04 00

Get BE EF 03 06 00 71 63 02 00 02 37 00 00

AUTO SEARCH Set OFF BE EF 03 06 00 B6 D6 01 00 16 20 00 00

ON BE EF 03 06 00 26 D7 01 00 16 20 01 00

Get BE EF 03 06 00 85 D6 02 00 16 20 00 00

AUTO KEYSTONE Set OFF BE EF 03 06 00 EA D1 01 00 0F 20 00 00

ON BE EF 03 06 00 7A D0 01 00 0F 20 01 00

Get BE EF 03 06 00 D9 D1 02 00 0F 20 00 00

DIRECT POWER ON Set OFF BE EF 03 06 00 3B 89 01 00 20 31 00 00

ON BE EF 03 06 00 AB 88 01 00 20 31 01 00

Get BE EF 03 06 00 08 89 02 00 20 31 00 00

CRC Action Type Setting Code

Command Data

(continued on next page)

Page 98

RS-232C Communication command table (continued)

Names Operation Type Header

AUTO POWER OFF Get BE EF 03 06 00 08 86 02 00 10 31 00 00

Increment BE EF 03 06 00 6E 86 04 00 10 31 00 00

Decrement BE EF 03 06 00 BF 87 05 00 10 31 00 00

LAMP TIME Get BE EF 03 06 00 C2 FF 02 00 90 10 00 00

LAMP TIME Reset Execute BE EF 03 06 00 58 DC 06 00 30 70 00 00

FILTER TIME Get BE EF 03 06 00 C2 F0 02 00 A0 10 00 00

FILTER TIME Reset Execute BE EF 03 06 00 98 C6 06 00 40 70 00 00

MY BUTTON-1 Set COMPUTER IN BE EF 03 06 00 3A 33 01 00 00 36 00 00

HDMI BE EF 03 06 00 CA 33 01 00 00 36 03 00

S-VIDEO BE EF 03 06 00 5A 32 01 00 00 36 02 00

VIDEO BE EF 03 06 00 AA 32 01 00 00 36 01 00

INFORMATION BE EF 03 06 00 FA 3E 01 00 00 36 10 00

AUTO KEYSTONE BE EF 03 06 00 6A 3F 01 00 00 36 11 00

MY MEMORY BE EF 03 06 00 9A 3F 01 00 00 36 12 00

PICTURE MODE BE EF 03 06 00 0A 3E 01 00 00 36 13 00

FILTER RESET BE EF 03 06 00 3A 3C 01 00 00 36 14 00

AV MUTE BE EF 03 06 00 AA 38 01 00 00 36 19 00

TEMPLATE BE EF 03 06 00 CA 39 01 00 00 36 1B 00

RESOLUTION BE EF 03 06 00 9A 3A 01 00 00 36 1E 00

ECO MODE BE EF 03 06 00 0A 25 01 00 00 36 37 00

Get BE EF 03 06 00 09 33 02 00 00 36 00 00

MY BUTTON-2 Set COMPUTER IN BE EF 03 06 00 C6 32 01 00 01 36 00 00

HDMI BE EF 03 06 00 36 32 01 00 01 36 03 00

S-VIDEO BE EF 03 06 00 A6 33 01 00 01 36 02 00

VIDEO BE EF 03 06 00 56 33 01 00 01 36 01 00

INFORMATION BE EF 03 06 00 06 3F 01 00 01 36 10 00

AUTO KEYSTONE BE EF 03 06 00 96 3E 01 00 01 36 11 00

MY MEMORY BE EF 03 06 00 66 3E 01 00 01 36 12 00

PICTURE MODE BE EF 03 06 00 F6 3F 01 00 01 36 13 00

FILTER RESET BE EF 03 06 00 C6 3D 01 00 01 36 14 00

AV MUTE BE EF 03 06 00 56 39 01 00 01 36 19 00

TEMPLATE BE EF 03 06 00 36 38 01 00 01 36 1B 00

RESOLUTION BE EF 03 06 00 66 3B 01 00 01 36 1E 00

ECO MODE BE EF 03 06 00 F6 24 01 00 01 36 37 00

Get BE EF 03 06 00 F5 32 02 00 01 36 00 00

CRC Action Type Setting Code

Command Data

(continued on next page)

Page 99

RS-232C Communication command table (continued)

Names Operation Type Header

MY BUTTON-BLANK Set COMPUTER IN BE EF 03 06 00 5A 31 01 00 08 36 00 00

HDMI BE EF 03 06 00 AA 31 01 00 08 36 03 00

S-VIDEO BE EF 03 06 00 3A 30 01 00 08 36 02 00

VIDEO BE EF 03 06 00 CA 30 01 00 08 36 01 00

INFORMATION BE EF 03 06 00 9A 3C 01 00 08 36 10 00

AUTO KEYSTONE BE EF 03 06 00 0A 3D 01 00 08 36 11 00

MY MEMORY BE EF 03 06 00 FA 3D 01 00 08 36 12 00

PICTURE MODE BE EF 03 06 00 6A 3C 01 00 08 36 13 00

FILTER RESET BE EF 03 06 00 5A 3E 01 00 08 36 14 00

AV MUTE BE EF 03 06 00 CA 3A 01 00 08 36 19 00

TEMPLATE BE EF 03 06 00 AA 3B 01 00 08 36 1B 00

RESOLUTION BE EF 03 06 00 FA 38 01 00 08 36 1E 00

ECO MODE BE EF 03 06 00 6A 27 01 00 08 36 37 00

BLANK BE EF 03 06 00 9A 00 01 00 08 36 40 00

FREEZE BE EF 03 06 00 0A 01 01 00 08 36 41 00

VOLUME BE EF 03 06 00 FA 01 01 00 08 36 42 00

AUTO BE EF 03 06 00 6A 00 01 00 08 36 43 00

Get BE EF 03 06 00 69 31 02 00 08 36 00 00

MY SOURCE Set COMPUTER IN BE EF 03 06 00 FA 38 01 00 20 36 00 00

HDMI BE EF 03 06 00 0A 38 01 00 20 36 03 00

S-VIDEO BE EF 03 06 00 9A 39 01 00 20 36 02 00

VIDEO BE EF 03 06 00 6A 39 01 00 20 36 01 00

Get BE EF 03 06 00 C9 38 02 00 20 36 00 00

Magnify Position H Get BE EF 03 06 00 C8 D7 02 00 10 30 00 00

Increment BE EF 03 06 00 AE D7 04 00 10 30 00 00

Decrement BE EF 03 06 00 7F D6 05 00 10 30 00 00

Magnify Position V Get BE EF 03 06 00 34 D6 02 00 11 30 00 00

Increment BE EF 03 06 00 52 D6 04 00 11 30 00 00

Decrement BE EF 03 06 00 83 D7 05 00 11 30 00 00

CRC Action Type Setting Code

Command Data

Page 100

Projector

CPWX8

User's Manual (concise)

Thank you for purchasing this projector. Please read through this manual before using this product, in order to use safely

and utilize well the product.

WARNING ►Before using this product, be sure to read all manuals for this

product. See “Using the CD manual” (15) to read the manuals in the CD. After reading them, store them in a safe place for future reference.

►Heed all the warnings and cautions in the manuals or on the product. ►Follow all the instructions in the manuals or on the product.

NOTE • In this manual, unless any comments are accompanied, “the

manuals” means all the documents provided with this product, and “the product”

means this projector and all the accessories came with the projector.

Contents



First of all............................................ 2

Entries and graphical symbols explanation ...... 2

Important safety instruction ..............................2

Regulatory notices.............................. 3

About Electro-Magnetic Interference................3

About Waste Electrical and Electronic Equipment

Contents of package........................... 4

Preparations ....................................... 5

Loading batteries into the remote control ......... 5

Arrangement....................................... 6

Connecting your devices .................... 7

Connecting power supply ................... 8

Turning on the power.......................... 8

Adjusting the projector's elevator ....... 9

Displaying the picture ....................... 10

Turning off the power........................ 11

...4

Replacing the lamp........................... 12

Cleaning and replacing the air lter.. 14

Using the CD manual .......................15

Specications ...................................16

Troubleshooting

- Warranty and after-service........... 17

ENGLISH



Hitachi CP-WX8 Operating Guide

Specifications and Main Features

Frequently Asked Questions

User Manual