Hitachi CP-S830W-E User Manual

ENGLISH

This Liquid Crystal Projector can display various

computer signals and NTSC/PAL/SECAM video

signals.

Outline

(1) High brightness

A highly efficient optical system with a UHB lamp ensures

high brightness.

(2) High resolution

Three separate high-definition liquid crystal panels are

used for the R, G and B signals.

(3) Compact size, light weight for portability
(4) RGB output terminal
(5) RS232C Communication
(6)

Mouse emulation

(7)

Complies with VESA DDC1/2B specifications

Contents

Page

Features

Before use ............................3

Names and functions of each

part ................................7

Installation ..........................11

Basic operations..................12

Adjustments and functions ..14
Connection to the video signal

terminals......................18

Connection to the RGB signal

terminal........................18

Connection to the control

signal terminal ............21

Example of system setup ....26

Cleaning the air filter ..........27

Lamp ..................................28

Message table ....................29

When you think something

wrong ..........................30

Specifications ......................31

Liquid Crystal Projector

Model name

Thank you very much for purchasing this Hitachi Liquid Crystal Projector.

Please read this operating guide to use correctly. After reading this manual, keep it carefully for

future reference.

OPERATING GUIDE

CP-S830W/E

As these colours may not correspond with the coloured makings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is

marked with the letter E or by the earth symbol or coloured Green or Green and Yellow.

The wire coloured Blue must be connected to the terminal marked with the letter N or coloured BLUE or

BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or

coloured BROWN or RED.

FOR THE CUSTOMERS IN U.K

THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE.

FOR THE U.K PLEASE REFER TO THE NOTES ON THIS PAGE.

IMPORTANT FOR UNITED KINGDOM

WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which

is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS

1362 fuse must be used of the same rating. If the fuse cover is detachable never use the plug with the cover

omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin

face of the plug. Fuse covers are available from your dealer.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points

in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved

extension lead or consult your dealer.

Should it be necessary to change the mains plugs, this must be carried out by a competent person,

preferable a qualified electrician.

If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having

first removed the fuse, to avoid a possible shock hazard by inadvertent connection to the mains supply.

2

Green & Yellow to Earth

Fuse

Cord Clamp

Brown to Live

Blue to Neutral

WARNING: THIS EQUIPMENT MUST BE EARTHED
IMPORTANT:

The wires in the mains lead are coloured in accordance with the following code:

Green and Yellow=Earth, Blue=Neutral, Brown=Live.

3

ENGLISH

Before use

Examples of

illustrated marks

(Before Use)

Illustrated marks Various illustrated marks are used in this product and instruction manual so

the product is used correctly and safely, and also to protect you and others from

danger and your property from being damaged.

This shows that a person could be killed or injured if the

wrong operation is done by ignoring this indication.

This shows that a person could be injured or material may be

damaged if the wrong operation is done by ignoring this

indication.

The mark informs you that there is a warning (including caution).

The concrete details of the warning (the left diagram shows the

caution for an electric shock hazard) is shown in the diagram.

The mark informs you of a prohibited action. The concrete

prohibited action (the left diagram shows the prohibition of

disassembly) is drawn in the diagram or near it.

The mark informs you of actions you must do. The concrete

instruction details (the left diagram shows "Disconnect the power

plug from the power outlet") is drawn in the diagram.

Warning
Caution

WARNING:This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications,

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

Instructions to Users:

This equipment complies with the requirements of FCC (Federal Communication Commission)

Class A equipments provided that following conditions are met.

(1) Video signal cables:

Double shielded coaxial cables (so called FCC shield cable) must be used and the outer shield must be

connected to the ground. Or, if normal coaxial cables are used, the cables must be enclosed in metal

pipes or similar way to reduce the interference noise radiation.

(2) Power cord:

Shielded power cord must be used. The outer shield must be connected to the ground.

(3) Video inputs:

The input signal amplitude must no exceed the specified level.

Warning

4

If any abnormality occurs.

· When there is an abnormal smell or smoke, if

you use this unit as it is, this could cause a

fire or electric shock, etc. When an

abnormality is found, immediately turn off the

power switch and pull out the power plug

from the power outlet. Check that there is no

smoke, etc., then contact your dealer to repair

the unit. Do not repair it yourself as it is very

dangerous.

· Do not use this unit as it

is after trouble has

occurred, such as "No

picture", "No sound", "Abnormal

sound", etc. This may cause a fire,

electric shock, etc. In this case

immediately turn off the power

switch and disconnect the power plug, then

contact your dealer to repair the unit.

· If water, etc. enters inside the unit, turn off the

power switch of the unit first and disconnect

the power plug and then contact your dealer.

If you use it as it is, it may cause a fire,

electric shock, etc.

Do not insert any foreign object.

· Do not insert a metal or flammable

object inside through the ventilation

holes, etc. This may cause a fire,

electric shock, etc.

· If foreign matter enters inside, turn

the power switch off and disconnect

the power plug from the power

outlet and contact your dealer. If

you use as it is, it may cause a fire,

electric shock, etc. Be careful

especially if children could touch the unit.

Pull out the
power plug
from the
power
outlet.

Do not put a container, etc. with

liquid on this unit.

Do not put a vase, flowerpot,

cosmetic container, medicine or

water and small metal objects on this unit. If

liquid spills and enter inside the unit, it may

cause a fire, electric shock, etc.

Do not apply any shock.

If you drop this unit or if the cabinet

is broken, turn off the power switch,

disconnect the power plug and

contact your dealer. If you use it as

it is, it may cause a fire, electric

shock, etc.

(Safety precaution)

Do not install this unit in an unstable place.

Avoid placing it in an unstable place

such as weak base, inclined floor, etc.

This may cause it to drop or fall over,

resulting in injury.

Do not open the cabinet.

Do not open the cabinet.

There are high voltage

parts inside the cabinet

and this may cause an

electric shock. Ask your

dealer to check inside and adjust and

repair the unit.

Do not remodel this unit.

Do not remodel this unit. It may

cause a fire, electric shock, etc.

Do not use this in a bathroom, etc.

Do not use this unit in a bathroom,

etc. This may cause a fire, electric

shock, etc.

Do not use
near water

Do not look directly at the lens when

the lamp is lit.

Do not look directly at the lens when

the lamp is lit. Since a strong light

is used, it could damage you vision, etc.

Especially pay attention if children are present.

Do not use power supplies other

than that specified.

Do not use this unit with a power

voltage other than specified power

supply voltage. It may cause a fire, electric

shock, etc.

Prohibition
of
disassembly

Electric shock
hazard

Pull out the
power plug
from the
power
outlet.

Pull out the
power plug
from the
power
outlet.

Prohibition
of
disassembly

· If the cord is damaged (core wire is

exposed, disconnected, etc.), ask

your dealer to replace it. It may

cause a fire, electric shock, etc.

· Check that no dirt adheres to the power plug

and fully insert without any play. If dirt

adheres or the connection is incomplete, it

may cause a fire, electric shock,

etc.

· The outer shield of power cord must

be connected to ground.
If you do not, it may cause a electric shock.

5

ENGLISH

Be careful in handling the power cord.

· Do not scratch, damage or process the power
cord. Do not bend it forcibly. Also do not put a
heavy object on it, do not heat it and do not pull
it. If you do, the power cord may be damaged
and it may cause a fire, electric shock, etc.

× Do not pull the cord.
× Do not put a heavy object on it.
× Do not damage the cord.
× Do not put it near a heating

device.

· Be careful that this unit is not placed
on the power cord. The power cord may be
damaged and it may cause a fire, electric shock,
etc. If the cord is covered with a carpet, etc. a
heavy object may be put on it without your
realizing it.

Warning

Caution

Do not step on this unit or do not put a

heavy object on it.

· Do not step on this unit. Especially
pay attention if children are
present. If you do, the unit may fall
over or may be broken causing an injury.

· Do not put a heavy object on this unit. If you
do, the unit may fall due to its imbalance or it
may drop, causing an injury.

Do not block the ventilation holes.

Do not block the ventilation holes. If
the ventilation holes are blocked, the
heat inside may build up and it may
cause a fire. Do not use this unit in
the following ways: On its side. In a
poorly ventilated, narrow place. On
a carpet or bedspread. Covered with a
tablecloth. Place this unit so that the
ventilation holes are kept 10cm or more away
from the wall.

Do not place this unit in a moist or dusty place.

· Do not place this unit in a moist or dusty place.
It may cause a fire, electric shock, etc.

· Do not place this unit where it would
be exposed to soot or steam, near a
cooking stove or humidifier, etc. It
may cause a fire, electric shock, etc.

Set the caster stoppers.

When this unit is installed on the
table with casters, set the caster
stoppers. If the table moves, it may
fall over, causing an injury.

Handle the power cord carefully.

· Do not bring the power cord near a heating
device. The shield of the cord may melt and it
may cause a fire, electric shock, etc.

· Do not insert / disconnect the power
plug with wet hands. It may cause
an electric shock.

· When the power plug is to be
disconnected, do not pull the
power cord. The power cord
may be damaged and it may
cause a fire, electric shock, etc.
Be sure to hold the power plug.

Cleaning

Be sure to pull out the power plug

from the power outlet for safety

when cleaning.

Pull out the power
plug from the
power outlet.

Caution when carrying it.

When this unit is to be moved, apply
a cover to the lens and be sure to
disconnect the power plug from the
power outlet and check that all
external connection cords are
removed before moving it. If not, the
cord may be damaged and it may
cause a fire, electric shock, etc.

Pull out the
power plug
from the power
outlet.

ENGLISH

6

Do not place this unit where it gets hot.

Be careful since if you place the unit
outdoors, in a place exposed to direct
sunlight or near a heating device,
the cabinet and parts could be
affected.

Cleaning the lens.

To clean the lens, use a generally­available lens cleaning tissue (used
for cleaning lens of camera, glasses,
etc.). Be careful not to scratch the
lens with a hard object.

Volume.

Use at the proper volume level so that it does
not bother persons in the neighborhood.
Especially, since the sound is likely to carry
well at the night even at a low volume, consider
the neighborhood to a good living environment.

(General cautions)

Cleaning the cabinet.

· Since many plastic materials are used on the
surface of the cabinet, if the surface is cleaned
using benzene, thinner, etc., it may change in
quality or the coating may be peeled off.
Avoid using chemicals.

· When a chemically-teated cloth is used, follow
the cautions that come with the cloth.

· Do not spray a volatile agent such as
insecticide on the unit. Do not leave a rubber
or vinyl object touching the cabinet for a long
time. It may cause the cabinet to change in
quality or the coating to peel off.

· Clean the dirt from the cabinet and operation
panel by dusting lightly with a soft cloth. If
the dirt is conspicuous, wipe off with a cloth
moistened with detergent diluted with water,
then wipe off with a dry soft cloth.

Rest your eyes occasionally when
viewing for a long time.

When you are not going to use

for a long time.

When you are not going use this unit
for a long time because you are going
on a trip, etc., be sure to pull out the
power plug from the power outlet for
safety. And also apply cover to the
lens so that the lens is not damaged.

Clean inside the unit at least once two years.

Ask your dealer to clean inside the unit at least
once two years. If the unit is left
with too much dust inside as it is for
a long this without cleaning, it may
cause a fire. Especially it is effective
to clean before the rainy season
starts. Consult your dealer for the cost of the
cleaning the inside the unit.

Pull out the
power plug
from the
power
outlet.

Caution

Use of batteries.

· Do not use batteries not specified
for this unit. Do not use new
batteries mixed together with old
ones. This may cause a fire, injury
due to burst of battery, liquid
leakage.

· When inserting batteries in this unit, pay
attention to the direction of the
and polarity indications and
insert the batteries correctly. If the
polarities are confused, it may
cause injury or damage near the
unit due to burst batteries, liquid

Caution when replacing the lamp.

· When replacing the lamp, turn off the power of
the projector and disconnect the power plug
from the power outlet. Then wait
for 45 minutes to allow the lamp
cool: Failure to do so could result in
a burn.

·

For disposal of used lamp, treat

according to the instruction of
community authorities.

· Since the lamp is made of glass, do
not apply shock to it and do not
scratch it.

· Also, do not use old lamp. This could also
cause explosion of the lamp.

· If it is probable that the lamp has exploded
(explosive sound is heard), disconnect the
power plug from the power outlet and ask
your dealer to replace lamp. The lamp is
covered by front glass and air-tight structure,
but, in rare cases, the reflector and the inside
of the projector may be damaged by scattered
broken pieces of glass, and broken pieces
could cause injury when being handled.

· When the lamp has been replaced, reset the
accumulated operation time of the lamp.
Do not reset if the lamp has not been replaced.

Pull out the
power plug
from the
power
outlet.

Reflector

Front glass

Lamp

7

ENGLISH

Main unit

Lens

Speaker

Speaker

Remote control
sensor

· Use the remote control transmitter within
the range of about 16 feet from the remote
control sensor and within 30° to both the
left and right.

Cooling fan

(exhaust)

Names and functions of each part

Handle

ON indicator

This blinks in the standby mode and lights
in the operation mode.(See page 30)

STANDBY / ON button

Power ON/OFF button.
OFF sets the unit in standby mode.
(see page 12~13)

LAMP indicator

This lights or blinks when the lamp does
not light. (See page 30)

TEMP indicator

This lights or blinks when temperature
inside the projector is too high or when fan
is abnormal.(See page 30)

INPUT button

To select the input source.
Each time this button is pressed, the input
source is changed in sequence as shown
below.

ZOOM knob

Adjusts picture size.
(See page 12)

FOCUS ring

Adjusts focus.
(See page 12)

MENU button

Picture adjustments.
Refer to page 14~17 for details.

RESET button

Resets unit to factory settings.
(See page 14)

Lens cap

MUTE button

Silences the sound. (Cancels the mute
when the unit is set in mute mode.)

RGB1

RGB2 VIDEO1

VIDEO2

RESET

MENU

MUTE INPUT

LAMP TEMP

ON

STANDBY/ON

8

Names and functions of each part (continued)

RGB input terminal

D-sub 15pin shrink terminal(1/2)

VIDEO input terminal

(on video-equipped models only)

S-VIDEO input terminal

Mini DIN 4pin connector(1/2)

VIDEO input terminal

RCA Jack(1/2)

AUDIO L/R input terminal

RCA Jack(1/2)

AC IN socket

Connect the provided power cord.

MAIN POWER switch

Main power ON/OFF switch.

:OFF
:ON

RGB output terminal

D-sub 15pin shrink terminal
RGB output can be displayed
even in the standby mode.

CONTROL terminal

D-sub 15pin shrink
terminal

AUDIO input terminal

Stereo mini jack(1/2)

AUDIO output terminal
(RGB/VIDEO)

Stereo mini jack

Remote control sensor

RGB IN



AUDIO

IN

OUT

RGB OUT

CONTROL

1

2

12

INPUT

S-VIDEO

VIDEO

AUDIO

L

R

1

1

1

2

2

2

9

ENGLISH

Remote control transmitter

MENU STICK SWITCH

When menu screen is being displayed, an
adjustment item can be selected and
adjustment can also be done using this
switch. (See page 14)
When menu screen is not displayed, this
switch can move mouse cursor and also can
work as left click. (See page 21)
While pressing POSITION button, picture can
be moved up, down, left or right by moving
MENU STICK switch up, down, left or right.

CONTRAST button

Adjusts contrast.
(See page 15)

VOLUME button

Adjusts volume. The sound is loud or low
while pressing the Ò Ó or Ò Ó button.

MUTE button

Silences the sound. (cancels the mute when
the unit is set in mute mode.)
When indication shown below is red, sound is
muted. When it is green, sound is output.

MENU ON / OFF button

Displays or removes the on-screen menus.
(See page 14~17)

BRIGHT button

Adjusts bright.
(See page 15)

STANDBY / ON button

Power ON/OFF button.
OFF sets the unit in standby mode.
(See page 12, 13)

INPUT SELECT button

Selects the input source.
(See page 12)

Names and functions of each part (continued)

TIMER ON / OFF button

Displays the setting time by count down.
See page 17 ÒTIMEÓ of menu when you set
the minutes of timer.

BLANK ON / OFF button

Blanks picture: Refer to page 16 for setting of
BLANK.
Pressing the button again and keeping it
pressed will reveal picture from top to bottom.

RESET / RIGHT button

When displays the on-screen menus, resets
the menu item to factory settings.
(See page 14)
When removes the on-screen menus, works
as right quick button.

*1 Icon of POSITION

When the POITION button is pressed, the icon indicating picture
moving position will be displayed at the bottom right of the
screen.
In the video mode, the icon is displayed but has no function.

POSITION button

Moves the picture by MENU STICK SWITCH
when pressing the POSITION button.*1
Pressing only this button for 2 seconds
continuously returns the picture position to
initial setting.

RIGHT

RESET

STANDBY/ON







TIMER

BLANK

POSITION

VIDEO1/2

INPUT



RGB1/2

MENU



VOL

MUTE

VOLUME

10

Caution

Cautions on use of batteries

· Do not use batteries not specified for this unit.

Also do not use old and new batteries together.

It may cause a fire, injury due to burst of

battery or liquid leakage.

· When inserting batteries, pay attention to the

direction of the and polarity indications

and insert the batteries correctly. If the

polarities are confused, it may cause injury or

damage near the unit due to a burst of battery

How to insert batteries

Insert the provided batteries (AA or R6P) into the remote control transmitter.

Remove the battery
compartment cover.

Slide the battery compartment cover

in the direction of the arrow while

pressing slightly down on it.

Caution

· Do not drop the remote control transmitter or

apply any shock to it.

· Do not let the remote control transmitter get

wet and do not put it on a wet object. It may

cause a malfunction.

· If you are not going to use it for a long time,

remove the batteries from the remote control

transmitter.

· If operation of the remote control becomes

difficult, replace the batteries.

Cautions on use

Insert the batteries
as illustrated inside
the battery compartment.

Replace the cover.

Names and functions of each part (continued)

123

Please basically use liquid crystal projector at the
horizontal position.
If you use liquid crystal projector by the lens up
position, the lens down position and the side up
position, this may cause the heat inside to build up and
become the cause of damage.
Be especially careful not to install it with ventilation
holes blocked.

11

ENGLISH

Determine picture size and projection distance as illustrated below.

a:Distance from the projector to the screen.
(tolerance : 10%)

This screen size is full-screen size.(800 dots X 600 dots)

a

Screen

Installation

View from the top

View from the side

Adjust the projection position using the foot adjusters at the bottom of the projector.

View from the front

· Do not unlock the foot adjusters while you do not support the projector, to avoid falling of
the projector and causing an injury.

· Do not revolve the foot adjusters by force, the foot adjusters is damaged.

· Securely lock the adjuster.

· Do not apply unnecessary force from the upper side when lifting the projector. Otherwise,

projector may be damaged or a finger could be caught and cause injury.

1. Lift up the projector and press the button of the adjuster to release the lock.

2. Adjust the projection angle, release the button of the adjuster and securely lock it.

3. To adjust the angle slightly, revolve the foot adjusters.

Foot adjuster

Lens center

View from the side

A viewing angle of 0û~9û can be changed.

Installation of liquid crystal projector

Caution

Example of the projector and screen installation

How to use foot adjusters

Screen (inch)

a (inch)

Minimum Maximum

40 67 87

60 98 130

80 130 173

100 165 217

120 197 260

150 248 327

200 331

12

7

Press the INPUT button or the INPUT SELECT (VIDEO or
RGB) button to select the source of the signal to be projected
on the screen.

· The selected signal input is displayed at the bottom right of the screen
for 3 seconds.

Power on all connected equipment.

The method of connecting various equipment, see on the page 18~26.

Turn the MAIN POWER switch of the projector on.[ I : ON]

· The ON indicator will light up orange.

1

Press the STANDBY/ON button.

· The ON indicator blinks (green) and then lights (green).

· The ON indicator will blink green during warm-up and light up.

· Power cannot be turned on even if the STANDBY/ON button is pressed within 60 seconds after

power is turned off, since the lamp has cooled preparing for next lighting.

2

Adjust picture size using the projection lens ZOOM knob.

4

Adjust focus using the projection lens FOCUS ring.

5
6

Example on-screen display

Basic operations

3

Remove the lens cap.

RGB1

To project the picture

4

5

7

2

1

RIGHT

RESET

STANDBY/ON

MENU









TIMER



BLANK

VOL

MUTE

POSITION

VIDEO1/2

RGB1/2

INPUT

2

3

7

RESET

MENU

MUTE INPUT

LAMP TEMP

ON

STANDBY/ON

13

ENGLISH

Basic operations (continued)

· To reduce temperature inside the projector (cooling down), fan will rotate for about 1 minute
after the lamp is turned off.

· Do not turn off the MAIN POWER switch during the lamp on because the lamp is damaged.

Press the STANDBY/ON button, for 1 second.

· The ON indicator lights up orange and the lamp turns off. (About 1 minute later), the fan stops and
the indicator blinks orange.

· Press the STANDBY/ON button for short time (less than 1 second), the projector do not set in
standby mode.

1

Turn the MAIN POWER switch of the projector off.[ : OFF]

2
3

Install the lens cap.

Caution

This projector complies with VESA DDC1/2B specifications. PLUG&PLAY is a system with computer,

peripherals (including projectors), and operating system.

It works when the projector is connected to DDC (Display Data Channel) ready computer that is running

an operating system software that incorporates plug & play functionality.

(Only RGB 1)

To turn off the power

PLUG&PLAY

1

2

RIGHT

RESET

STANDBY/ON

MENU









TIMER



BLANK

VOL

MUTE

POSITION

VIDEO1/2

RGB1/2

INPUT

1

3

RESET

MENU

MUTE INPUT

LAMP TEMP

ON

STANDBY/ON

14

Press the MENU ( ) buttons or the MENU ON /
OFF button.

· On-screen menus are displayed on the screen.

1

Select the menu to be adjusted using the MENU ( )
buttons or MENU STICK SWITCH.

· Menu displayed in green is selected.

2

Select the item to be adjusted using the MENU ( )
buttons or MENU STICK SWITCH.

· Item displayed in green can be adjusted.

When no operation is done for about 5 ~ 10 seconds, menu screen will go off.

3

Individual memory functions are provided for the VIDEO1, VIDEO2, RGB1 and RGB2 input terminals.

Adjustments are saved after power off.

· Resetting menu items (SETUP, INPUT, IMAGE, OPT.)

(1)

Select the menu item to return to the initial setting.

(2)

Press the RESET button.

(3)

Select the DEFAULT (To select the CANCEL is not changed).

(Display shown on the right will appear.)

· Resetting adjustment items (VOLUME, BRIGHT etc.)

(1)

Select the adjustment item to return to the initial setting.

(2)

Press the RESET button.

Adjustments and functions

Memory function

To return to the initial setting

1

2, 3

1, 2, 3

RIGHT

RESET

STANDBY/ON

MENU









TIMER



BLANK

VOL

MUTE

POSITION

RESET

MENU

MUTE INPUT

ON

LAMP TEMP

STANDBY/ON

SETUP INPUT IMAGE OPT.

VOLUME
BRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
COLOR BAL

RESET 'SETUP'

DEFAULT
CANCEL

R B

15

ENGLISH

RGB signal input VIDEO signal input

The menu SET UP serves for the change of parameters influencing the picture and for the move picture

position.

Adjustments and functions (continued)

· When start up screen is displayed (''NO INPUT IS DETECTED'' or ''SYNC IS OUT OF
RANGE'' is displayed), SETUP menu items other than VOLUME cannot be set.

· TINT cannot be adjusted with PAL/SECAM video signal input.

· TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input.

· V.POSIT, H.POSIT, H.PHASE and H.SIZE cannot be adjusted with a VIDEO signal input.

SET UP

Caution

SETUP INPUT IMAGE OPT.

VOLUME
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL

121

57

7

800

R B

SETUP INPUT IMAGE OPT.

VOLUME
BRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
COLOR BAL

R B

Adjustment Item Details of adjustment

VOLUME Decrease Increase

BRIGHT

(BRIGHTNESS)

Dark Bright

CONTRAST Lower Higher

SHARPNESS Soft Sharp

COLOR Less More

TINT Red Green

V.POSIT

(V.POSITION)

Moves the picture up or down.

H.POSIT

(H.POSITION)

Moves the picture left or right.

H.PHASE Decreases the picture flicker.

H.SIZE Widens of Narrow the horizontal size of the picture.

COLOR BAL

(COLOR BALANCE)

for Red for Blue

16

Adjustments and functions (continued)

The menu INPUT serves for the selection of input source.

The menu IMAGE serves of the picture inversion.

SETUP INPUT IMAGE OPT.

MESSAGE

TURN ON
TURN OFF

SETUP INPUT IMAGE OPT.

MIRROR
BLANK
REVEAL
MESSAGE

SETUP INPUT IMAGE OPT.

BLANK

WHITE
BLUE
BLACK

SETUP INPUT IMAGE OPT.

REVEAL

FAST

MEDIUM

SLOW

SETUP INPUT IMAGE OPT.

MIRROR

NORMAL
H : INVERT
V : INVERT
H&V :
INVERT

INPUT

IMAGE

Adjustment Item Details of adjustment

RGB 1 Selects the RGB 1 terminal.

RGB 2 Selects the RGB 2 terminal.
VIDEO 1 Selects the VIDEO 1 terminal.
VIDEO 2 Selects the VIDEO 2 terminal.

SYSTEM

Selects the video signal systems.
When the picture (Video) is abnormal (no color or out of sync.), selects the input
signal mode (NTSC, PALM, SECAM, NTSC4.43 and M-PAL).

Adjustment Item Details of adjustment

MIRROR

Inverts the picture horizontally or vertically.

NORMAL Not invert.
H:INVERT Inverts the picture horizontally.
H:INVERT Inverts the picture vertically.
H&V:INVERTInverts the picture horizontally and vertically.

BLANK

Selects the blank color of signal or pressing BLANK ON button.
When start up screen is displayed, screen will blank out 5 minutes later.

REVEAL Selects the speed or revelation. See page 9 "BLANK ON button.

MESSAGE Turn off the on-screen message. (VOLUME, Input selection display)

SETUP INPUT IMAGE OPT.

RGB1
RGB2
VIDEO1
VIDEO2

SETUP INPUT IMAGE OPT.

SYSTEM

RGB1
RGB2
V I DEO1
V I DEO2

AUTO
NTSC
PAL
SECAM
NTSC4.43
M-PAL

17

ENGLISH

The menu OPT. allows you to control communication function etc.

Adjustments and functions (continued)

SETUP INPUT IMAGE OPT.

COM. SPEED
COM. BITS
TIMER
LANGUAGE
AUTO OFF
START UP

SETUP INPUT IMAGE OPT.

7N1
8N1

COM. BITS

SETUP INPUT IMAGE OPT.

1200
2400
4800
9600

19200

COM. SPEED

(bps)

SETUP INPUT IMAGE OPT.

LANGUAGE

ENGLISH
FRAN‚AIS
DEUTSCH
ESPA„OL
ITALIANO
NORSK
NEDERLANDS

SETUP INPUT IMAGE OPT.

TIMER

15 min.

SETUP INPUT IMAGE OPT.

START UP

TURN ON
TURN OFF

SETUP INPUT IMAGE OPT.

AUTO OFF

0 min.
STOP

OPT.

Adjustment Item Details of adjustment

COM. SPEED

(COMMUNICATION SPEED)

Selects the data speed of transmission. (five kinds)

COM. BITS

(COMMUNICATION BITS)

Selects the data format or transmission
7N1...7 data bits, No parity, 1 stop bit.
8N1...8 data bits, No parity, 1 stop bit.

TIMER Sets the minutes of timer. (0~99)

LANGUAGE

Selects the language on-screen menu.
(English, Francais, Deutsch, Espanol, Italiano, Norsk, Nederlands)

AUTO OFF

Sets time (minutes) from the start of displaying start up screen (No input is
detected or sync is out of range) to turning the power OFF.
"0" is stop and another "1~99"

START UP

Sets/releases start up screen displayed when power is turned on, or when no
input is detected or sync is out of range.

18

1. Input / output signal

Connection to the RGB signal terminal

2. Signal input / output terminal

51

10

6

15

11

D-sub 15pin shrink terminal
(Female)

1. Input signal

Connection to the video signal terminals

2. Signal input terminal

Ground

Luminance signal

S VIDEO input (Mini DIN4 pin)

Ground

Chrominance signal

Caution

Video input signal terminals have priority in the following order.

S-VIDEO input terminal RCA jack input terminal

2

1

Caution

Do not use RGB cable other than that specified.

Some RGB cable may not operate DDC (Display Data Channel)
because there are not connect from pin NO. to pin NO. .

12

15

S-VIDEO signal

Luminance signal 1.0Vp-p, 75W termination
Chrominance signal 0.286Vp-p (burst signal), 75W termination

VIDEO signal

1.0Vp-p, 75W termination

AUDIO signal

Input

200mVrms, 20kW below (MAX 3.0Vp-p)

Output

0~200mVrms, 1kW

Video signal

Analog 0.7Vp-p 75W termination (Positive polarity)

Horizontal sync signal TTL level (Positive/negative polarity)

Vertical sync signal TTL level (Positive/negative polarity)

Composite sync signal TTL level

Audio signal

Input

200mVrms, 20kW below (MAX 3.0Vp-p)

Output

0~200mVrms, 1kW

1 Video signal (Red)

2 Video signal (Green)

3 Video signal (Blue)

4 N.C

5 N.C

6 Ground (for R)

7 Ground (for G)

8 Ground (for B)

9 N.C

10 Ground

11 N.C

12

DDC (Display Data channel) RGB1 only

13 Horizontal/Composite sync signal

14 Vertical sync signal

15

DDC (Display Data channel) RGB1 only

19

ENGLISH

3. Example of computer signal

Note 1: Signal mode

Note 2: MAC adapter is necessary to the resolution mode.

Projector is compatible with 13 inch mode and 16 inch mode.

MAC13"mode=switch 1, switch 5 and switch 6 are ON.

MAC16"mode=switch 2, switch 5 and switch 6 are ON.

Note 3:Display mode

Connection to the RGB signal terminal(continued)

ON

1 2 3 4 5 6

(Example 16inch mode)

Caution

· Some input source may not be displayed properly because they are not compatible with the
projector.

· Some input source may not be displayed in full size as shown "Display Dots".

Resolution

HXV

fH

(kHz)

fV

(Hz)

Standard

Type

Note 1 Note 2 Note 3

Display Dots

HXV

640X350 31.5 70.1 VGA-1 Expanded 800X490

640X400 24.8 56.4

NEC

PC9800

Expanded 800X560

640X400 31.5 70.1 VGA-2 Expanded 800X560

640X480 43.3 85.0 VESA Expanded 800X600

640X480 31.5 59.9 VESA VGA-3 Expanded 800X600

640X480 35.0 66.7

Mac13"

mode

SW 1 ON
SW 5 ON
SW 6 ON

Expanded 800X600

640X480 37.9 72.8 VESA Expanded 800X600

640X480 37.5 75.0 VESA Expanded 800X600

800X600 35.2 56.3 VESA SVGA (56Hz) 800X600

800X600 37.9 60.3 VESA SVGA (60Hz) 800X600

800X600 48.1 72.2 VESA SVGA (72Hz) 800X600

800X600 46.9 75.0 VESA SVGA (75Hz) 800X600

800X600 53.7 85.1 VESA SVGA (85Hz) 800X600

832X624 49.7 74.5

Mac16"

mode

SW 2 ON
SW 5 ON
SW 6 ON

Partial 800X600

1024X768 48.4 60.0 VESA XGA (60Hz) Compressed 768X576

1024X768 56.5 70.1 VESA XGA (70Hz) Compressed 768X576

1024X768 60.0 75.0 VESA XGA (75Hz) Compressed 768X576

20

4. Initial set signals

The following signals are initially set. The settings may be different depending on the computer type. In

this case, adjust the settings referring to pages 14, 15.

Connection to the RGB signal terminal(continued)

Back porch(b)

Back porch(b)

DATA

HSYNC

DATA

VSYNC

Sync.(a)

Front porch(d)

Active(c)

Sync.(a)

Front porch(d)

Active(c)

Computer/signal

Horizontal Timing (µs)

abcd

VGA-1 3.8 1.9 25.4 0.6

PC-9800 3.0 3.8 30.4 3.0

VGA-2 3.8 1.9 25.4 0.6

VESA (85Hz) 1.6 2.2 17.8 1.6

VGA-3 3.8 1.9 25.4 0.6

Mac 13inch mode 2.1 3.2 21.2 2.1

VESA (72Hz) 1.3 4.1 20.3 0.8
VESA (75Hz) 2.0 3.8 20.3 0.5
SVGA (56Hz) 2.0 3.6 22.2 0.7

Computer/signal

Horizontal Timing (µs)

abcd
SVGA (60Hz) 3.2 2.2 20.0 1.0
SVGA (72Hz) 2.4 1.3 16.0 1.1
SVGA (75Hz) 1.6 3.2 16.2 0.3
SVGA (85Hz) 1.1 2.7 14.2 0.6

Mac 16inch mode 1.1 3.9 14.5 0.6

XGA VESA (60Hz)

2.1 2.5 15.8 0.4

XGA VESA (70Hz)

1.8 1.9 13.7 0.3

XGA VESA (75Hz)

1.2 2.2 13.0 0.2

Computer/signal

Horizontal Timing (µs)

abcd

VGA-1 3.8 1.9 25.4 0.6

PC-9800 3.0 3.8 30.4 3.0

VGA-2 3.8 1.9 25.4 0.6

VESA (85Hz) 1.6 2.2 17.8 1.6

VGA-3 3.8 1.9 25.4 0.6

Mac 13inch mode 2.1 3.2 21.2 2.1

VESA (72Hz) 1.3 4.1 20.3 0.8
VESA (75Hz) 2.0 3.8 20.3 0.5
SVGA (56Hz) 2.0 3.6 22.2 0.7

Computer/signal

Horizontal Timing (µs)

abcd
SVGA (60Hz) 3.2 2.2 20.0 1.0
SVGA (72Hz) 2.4 1.3 16.0 1.1
SVGA (75Hz) 1.6 3.2 16.2 0.3
SVGA (85Hz) 1.1 2.7 14.2 0.6

Mac 16inch mode 1.1 3.9 14.5 0.6

XGA VESA (60Hz)

2.1 2.5 15.8 0.4

XGA VESA (70Hz)

1.8 1.9 13.7 0.3

XGA VESA (75Hz)

1.2 2.2 13.0 0.2

21

ENGLISH

1. Control signal terminal

Connection to the control signal terminal

2. Mouse emulation

51

10

6

15

11

D-sub 15pin shrink terminal (Male)

Caution

Turn off the power of both the projector and computer before connecting.

Connect the computer to the control terminal of the projector using an appropriate cable.

Refer to the instruction manual of each device before connecting.

(1) Connect the projector and the mouse terminal of computer using an appropriate cable, while the

projector and the computer are turn off.

(2) Turn the power of the projector on and press the STANDBY/ON switch. The indicator will light.

(The ON indicator will light up orange.).

(3) Press the INPUT of the projector or RGB 1/2 button of the remote control transmitter and select the

input connection.

(4) Turn on the computer.

(5) Start mouse emulation mode.

If can not start mouse emulation, reset the computer. (With soft reset or reset switch)

(6) See on the page 9 about to operate the remote control transmitter.

Caution : Mouse cannot be operated while start up screen or menu screen is being displayed.

Caution

·

In some note computers which have internal pointing device, mouse emulation don't work

without setting the internal pointing device disabled. In this case, set the internal pointing

device disabled in BIOS setting. After setting in BIOS, operate (1) ~ (5) Please check its

hardware manuals to disable internal pointing device in BIOS setting.

·

In some computers, mouse emulation don't work without the utility program. In this case,

see and check the operating manuals of the computer.

.oNniPC232-SR

esuoM

2/SPBDAlaireS

1MDT

2KLCATADS

3ATAD

4

5

60LES0LES

71LES1LES

8YDAER

9

01DNGDNGDNGDNG

11

21V5+V5+

31PDR

41PDT

51

22

Connection to the control signal terminal (continued)

PS/2 mouse

ADB (Mac) mouse

Serial mouse

2

1

4

3

6

5

2

1

4

3

6

5

8

7

10

9

12

11

14

13

15

XA,CLK,SDATA

XB,DATA

SW-L,SEL0

SW-R,SEL1

READY

GND

+5V

DATA

GND
+5V
CLK

TDM

YA
YB

RDP

TDP

2

1

4

3

6

5

2

1

4

3

8

7

10

9

12

11

14

13

15

XA,CLK,SDATA

TDM

SW-R,SEL1

GND

+5V

DATA

GND

+5V

(

POWER ON

)

XB,DATA

YA

YB

SW-L,SEL0

READY

RDP

TDP

2

1

4

3

6

5

2

1

4

3

6

5

8

7

10

9

8

7

9

12

11

14

13

15

RI

CD

RD

TD
DTR
GND
DSR

CTS

RTS

XA,CLK,SDATA

TDM

SW-R,SEL1

GND

+5V

XB,DATA

YA

YB

SW-L,SEL0

READY

RDP

TDP

1

2

3

4

5

6

1

2

3

4

45

2

3

9

1

7

6

8

Projector Computer

Mini Din 6pin

Mini Din 4pin

Projector Computer

PS/2 cable

ADB cable

D-sub 9pin

Projector Computer

Serial cable

(Cbale side)

(Cable side)

(Cable side)

Caution

Serial mouse cannot be operated with provided RS-232C cable.

Purchase exclusive serial mouse cable separately.

Type name : SC-MS200 (Serial mouse) Parts No. : EW02881

23

ENGLISH

Connection to the control signal terminal (continued)

3. Communication

(1) Connect the projector and computer using RS 232C cable.

(2) Turn off the computer and after computer is setting up, turn on the projector.

(3) Select the data speed (COM.SPEED) and the data format (COM.BITS) of the projector. (See page 17)

(4) Start communication.

4. Control command table

Control command table

2

1

4

3

6

5

2

1

4

3

6

5

8

7

10

9

8

7

9

12

11

14

13

15

RI

CD

RD

TD
DTR

GND
DSR

CTS

RTS

XA,CLK,SDATA

TDM

SW-R,SEL1

GND

+5V

XB,DATA

YA

YB

SW-L,SEL0

READY

RDP

TDP

45

2

3

9

1

7

6

8

Projector Computer

D-sub 9pin

RS232C cable

(Cable side)
(Reference)

Projector®Computer Computer®Projector

Item

Reply code Ask code Set code Default code

1st 1st 1st 1st
MOUSE 11h 20h 31h 40h
COMMUNICATE 11h 20h 31h 40h
POWER 11h 20h 31h
MIRROR 11h 20h 31h 40h
INPUT 11h 20h 31h 40h
(VIDEO) SYSTEM

12h 20h 32h 40h
VOLUME 11h 20h 31h 40h
MUTE 11h 20h 31h 40h
BRIGHT 13h 20h 33h 40h
CONTRAST 13h 20h 33h 40h
COLOR 13h 20h 33h 40h
TINT 13h 20h 33h 40h
SHARPNESS 13h 20h 33h 40h
H. PHASE 13h 20h 33h 40h
H. POSIT 14h 20h 34h 40h
H. SIZE 14h 20h 34h 40h
V. POSIT 14h 20h 34h 40h
BLANK 11h 20h 31h 40h
REVEAL 11h 20h 31h

2nd
05h
06h
11h
14h
21h
22h
23h
24h
31h
32h
33h
34h
35h
37h
38h
36h
3Ah
41h
42h

data

+1
+1
+1
+1
+1
+2
+1
+1
+3
+3
+3
+3
+3
+3
+4
+4
+4
+1
+1

2nd
05h
06h
11h
14h
21h
22h
23h
24h
31h
32h
33h
34h
35h
37h
38h
36h
3Ah
41h
42h

2nd
05h
06h
11h
14h
21h
22h
23h
24h
31h
32h
33h
34h
35h
37h
38h
36h
3Ah
41h
42h

data

+1
+1
+1
+1
+1
+2
+1
+1
+3
+3
+3
+3
+3
+3
+4
+4
+4
+1
+1

2nd
05h
06h

14h
21h
22h
23h
24h
31h
32h
33h
34h
35h
37h
38h
36h
3Ah
41h

24

Connection to the control signal terminal (continued)

Control data table

Caution

If computer sends the undefined command code or data code, Projector can not guarantee operation.

Command is consisted of 2 command bytes and following data bytes.

1-st byte indicates the kinds of commands and the length of command.

'0xH' : Error-reply Projector sends to computer.

'1xH' : Command reply Projector sends to computer.

'2xH' : Ask command Computer sends to Projector.

'3xH' : Set command Computer sends to Projector.

'4xH' : Default set command Computer sends to Projector

'5xH' - 'FxH' : Reserved

'x' indicates the length of data bytes.

2-nd byte indicates the command code 'yy' as command table.

Data table shows the data byte.

Item Data code

MOUSE 00h=stop mouse emulation. 01~7Fh=start mouse emulation

COMMUNICATE

0Xh=8N1
1Xh=7N1
X0h=1200bps, X1h=2400bps, X2h=4800bps, X3h=9600bps, X4h=19200bps

POWER 1Eh=Power off (Standby mode), 1Fh=Power on

MIRROR 00h=Normal, 01h=H:Invert, 02h=V:Invert, 03h=H&V:Invert

INPUT 11h=VIDEO1, 12h=VIDEO2, 21h=RGB1, 22h=RGB2
VIDEO

SYSTEM

00h 00h=Auto, 00h 01h=NTSC, 00h 04h=NTSC4.43
00h 02h=PAL, 00h 03h=SECAM, 00h 05h=M-PAL

VOLUME 00h (min) ~ 24h (max)

MUTE 00h=Mute off, 01h=Mute on

BRIGHT 00h 00h 00h (dark) ~ 00h 00h 24h (brite)

CONTRAST 00h 00h 00h (lower) ~ 00h 00h 24h (higher)

COLOR 00h 00h 00h (less) ~ 00h 00h 24h (more)

TINT 00h 00h 00h (red) ~ 00h 00h 24h (green)

SHARPNESS 00h 00h 00h (soft) ~ 00h 00h 24h (sharp)

H. PHASE 00h 00h 00h ~ 00h 00h 1Fh

H. POSIT 00h 00h 00h 00h (left) ~ 00h 00h 37h 04h (right)

H. SIZE 00h 00h 78h 05h (narrow) ~ 00h 00h 30h 0Eh (wide)

V. POSIT 00h 00h 01h 00h (down) ~ 00h 00h 58h 04h (up)

BLANK

0Xh=Blank off
1Xh=Blank on

bit0 0=Blue off, 1=Blue on, bit1 0=Green off, 1=Green on
bit2 0=Red off, 1=Red on, bit3 0=Not change, 1=change

REVEAL X1h=Reveal down, X4h=Reveal right, X=0 (slow) ~ 7 (fast)

25

ENGLISH

The procedure of getting the Projector status

(1)Computer sends the command '20H'+'yyH' to Projector.

(2)Projector reply the command '1xH'+'yyH'+data bytes.

The procedure of setting the Projector status

(1)Computer sends the command '3xH'+'yyH'+data bytes.

(2)Projector changes itÕs status.

(3)Projector reply the command '1xH'+'yyH'+data bytes which indicate status.

The procedure of default setting the Projector status

(1)Computer sends the command '40H'+'yyH'

(2)Projector changes it's status to default setting.

(3)Projector reply the command '1xH'+'yyH'+data bytes which indicate default.

Connection to the control signal terminal (continued)

Caution

If projector replys '4Dh', (before command code, etc.) computer ignores '4Dh'

Caution

The example of command error

When projector cannot accept command from PC, error code '00H'+'yyH' is sent back.

(in a case when command code '2xH', '3xH' or '4xH'+'yyH'+data is sent from PC to projector)

The example of data error

When projector cannot accept command from PC, error code with data '00H'+'yyH'+data is sent back as it

is. (in a case when command code '2xH', '3xH' or '4xH'+'yyH'+data is sent from PC to projector)

When data is longer than required data code length, projector ignores excess data code.

When data is shorter than required data code length, projector sends back error code shown above.

The example of framing error

After setting to 1200bps 7N1, projector sends error code '70H'+'70H' up to 10 times at intervals of 1 second

until any answer is received. When projector receives framing error code ('70H'+'70H'),

'12H'+'03H'+'03H'+'10H' is sent with 1200 bps 7N1.

The interval of command bytes and data bytes

After command code '2xH', '3xH' or '4xH' is sent from PC, if command or data is not sent within 500ms,

projector sends back error command '70H'+70H'. If no answer is sent within 1 second from that time,

framing error is assumed.

Caution

· The interval of command bytes and data bytes must be over 1mS and under 500mS. If it is
under 1mS, it may be treat as framing error.

· After projector has sent back answer code, when next command is to be sent from PC, allow
for an interval of 40ms or more between answer code and other code.

· (3) data bytes is not always same as (1) data bytes. If projector cannot realize the status of (1)
data bytes, projector set the proper status and reply this new setting data bytes or projector
reply the error reply '0xH'+'yyH'+data bytes same as (1).

· When only power control (POWER COMMAND) is performed, it takes about 2~80 seconds
between sending set code and receiving answering code.

INPUT

S-VIDEO

VIDEO

AUDIO

L

R

1

1

1

2

2

2

RGB IN

AUDIO

IN

OUT

RGB OUT

CONTROL

1

2

12

26

Example of system setup

Connecting various equipment.

AC Inlet

Computer(Desk type)

Computer (Note type)

VTR with S-VHS out

(video model only)

VTR, etc.

(video model only)

CRT Display

Audio amplifying equipment

Caution

· Turn power off to all devices before connecting.

· Refer to the instruction manual of each device before connecting.

1

Liquid crystal projector

Core

Computer

· To protect from radio interference, core is attached to each provided or optional cable: Do
not use cables other than provided cables and optional cables.

· Since both ends of audio cable are the same shape, either end can be connected to any side.

However, use the cable with the core set to the projector side.

27

ENGLISH

Clean the air filter about every 100 hours or when "CHECK THE AIR FLOW" is displayed.

Cleaning the air filter

Turn the main power switich off and disconnect the power
plug from the power outlet.

1

Remove the air filter from the bottom.

2

Clean the air filter using a vacuum cleaner.

· When air filter is very dirty, wash it using neutral detergent diluted with water, and dry well.

3

Install the air filter.

4

Caution

· If air filter is stutted with dust, etc., protection circuit will turn the power off.

· "CHECK THE AIR FLOW" is displayed when you block the ventilation holes.

28

Lamp

Light source lamp has a service life.
The picture will become dark or color will be poor when the lamp is used for a long time.
If usage of lamp is continued in such cases, it could cause a malfunction. Replace lamp with new one.
As reference for replacement time, indicator will operate or message will be displayed when the power is
turned on, as shown on page 29~30. In these cases the lamp should be replaced. Consult your dealer.

1. How to replace lamp

Turn the main power switch off and disconnect the power
plug from the power outlet.

1

Remove the lamp cover.

· If lamp is hot at this time, this could cause burn. Wait
for about 45 minutes until lamp is cooled down.

· Loosen a screw and remove the cover.

2

Loosen two screws and pull
the handle to remove the
lamp.

· If the screws are not loosened completely, your fingers
may be damaged.

3

Replace the lamp with
new one and fix it using
the same two screws.

4

Lamp cover

HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE

When replacing lamp, turn off and remove AC cord, wait 45 minutes to let lamp cool.
High-pressure lamp when hot, may explode if improperly handled.

Screw

Screw

(Option lamp : Lamp unit CP-S830W/E DT00171)

Caution

·

For disposal of used lamp, treat according to the instruction of community authorities.

· Since the lamp is made of glass, do not apply shock to it and do not scratch it.

· Also, do not use old lamp. This could also cause

explosion of the lamp.

· If it is probable that the lamp has exploded
(explosive sound is heard), disconnect the power
plug from the power outlet and ask your dealer to
replace lamp. The lamp is covered by front glass
and air-tight structure, but, in rare cases, the
reflector and the inside of the projector may be
damaged by scattered broken pieces of glass, and
broken pieces could cause injury when being handled.

· Do not insert your hand into the box after the lamp is removed.
(There are optical parts inside. If touched by hand, it may result in color unevenness, etc.)

Caution

Also LAMP indicator will light when the lamp becomes too hot. Turn off the power and let the
projector cool for 45 minutes. Turn on. If LAMP indicator still lights up red, contact your
dealer.

Lamp

Reflector

Front glass

Lamp

29

ENGLISH

Install the lamp cover and fix it using screws.

· To prevent burn, install the lamp cover and secure it using screws.

· When the lamp cover is out of place, the power does not turn on. Before you turn

on the power, make sure to attach the lamp cover and fix it with the scrcws.

5

Lamp

(continued)

Please carry out the following operation within 10 minutes from power on, if you replaced the lamp after

2,000 hours.

2. Reset the lamp time

3

1

2

RIGHT
RESET

STANDBY/ON

MENU









TIMER



BLANK

VOL

3

1, 2

1) Press the RESET button on projector for 3 seconds or remote control TIMER
button for 3 seconds and display the total lamp used time.

· When accumulated operation time of the lamp reaches 1700 hours, the
following display will appear at the bottom of the screen.

2) Press the RESET button on projector or remote control MENU ON button
during displaying the lamp used time.

3) Select the Ò0Ó on the screen using the MENU ( ) button or MENU STICK
SWITCH.

LAMP 1700 0 CANCEL

LAMP 1700 h

®Ÿ

Whenever the lamp is replaced, reset the total operation time of the lamp.
Do not reset if the lamp has not been replaced.

On-screen display

The following messages are displayed on the screen.

Message table

*1 This message are not displayed after 3 minutes.

But this message are displayed when you turn on the power again.

MESSAGE Action

CHANGE THE LAMP
"AFTER REPLACING LAMP,
RESET THE LAMP TIMER."

Accumulated operation of lamp has exceeded 1,700 hours. It is recommended
to replace lamp. Replace with new lamp. If accumulated operation reaches
2,000 hours, lamp will automatically turn off. *1

CHANGE THE LAMP
"AFTER REPLACING LAMP,
RESET THE LAMP TIMER."
THE POWER WILL TURN
OFF AFTER 20 Hr.

Lamp has 1,979 hours on it.
Call a maintenance person. *1
Time is 20 ~ 0. (count down.)

Blinking of
"CHANGE THE LAMP"

When the lamp has 2,000 hours or more on it, the message will blink, and the
power will turns off after 10 minutes.

NO INPUT IS DETECTED Signal is hot input. (See page 18, 19)

SYNC IS OUT OF RANGE

The horizontal frequency of the input signal exceeds the range of the projector,
it cannot be displayed. (See page 19, 20)

CHECK THE AIR FLOW Clean the air filter of remove the blocking ventilation holes. (See page 27)

RESET

MENU

MUTE INPUT

ON

LAMP TEMP

STANDBY/ON

30

Check the following again before asking for service. If the trouble cannot be recovered, consult your dealer.

When you think something wrong

A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem.

Message table (continued)

The ON indicator, LAMP indicator and TEMP indicator will light or
blink in the following cases.

Indicator display

When the LAMP indicator lights, turn the power off. If the problem cannot be recovered, contact your dealer.

*1 Even when the indicator lights green, if the power supply section becomes too hot , the lamp may be automatically

turned off to cool it down (indicator continues to light green). In this case, turn off the power switch and allow the
unit to cool down before turning the power switch on again. The lamp will light. If the lamp does not light because it
is still automatically turned off, contact your dealer.

*2

When inside temperature becomes high because ventilation holes are blocked, normally, TEMP indicator

will light red. However, to protect the projector, the lamp may be turned off and at this time LAMP
indicator may light red.

ON indicator LAMP indicator TEMP indicator Meaning Remedy

Lights orange Goes off Goes off Standby mode

Blinks green Goes off Goes off During warming up

Lights green Goes off Goes off During operation *1

Blinks orange Goes off Goes off During cooling down

Lights red Lights red Goes off Lamp cannot light

Cool projector by power off for 45
minutes.
If the indicator is still it, lamp may be
defective. Replace.

Lights red Blinks red Goes off

Lamp is not inserted or the
lamp door open

Securely insert the lamp or close the
lamp door.

Lights red Goes off Lights red Temperature inside too hight

Correctly reinstall so as not to block
ventilation holes.

Lights red Goes off Blinks red Cooling fan accidented Call a maintenance person.

Blinks red Blinks red Goes off

Accumulated lamp operation
time has exceeded 2,000
hours

Replace lamp and reset the
accumulated lamp operation time.
(See page 28, 29)

Phenomena Cause Check point Page

Power cannot be
turned on.

·

The Main power is not turned on.

·

The power cord is disconnected.

·

60 seconds have not elapsed since the
power was turned off.

·

Turn the MAIN POWER switch on.

·

Insert the power cord into an AC socket.

·

When the power is turned off turn the power
switch on after waiting at least 60 seconds.

P.12
P.8
P.12

No picture and
sound

·

The setting of the input source is not
correct.

·

Wiring to the projector is not correct.

·

Set the correct input using the input select
button of the projector or the remote control.

·

Connect the cable correctly.

P.7, 9,
12, 16
P.8, 26

Only picture is
displayed with no
sound

·

Wiring to the projector is not correct.

·

The volume is set to minimum.

·

The unit enters the mute mode.

·

Connect the cable correctly.

·

Press the VOL button or press the MENU button
and adjust the volume.

·

Press the MUTE button.

P.8, 26
P.9, 15

P.7, 9

Only sound is
heard without a
picture

·

Wiring the projector is not correct.

·

The brightness is set fully to the dark
side.

·

Lens cap is attached.

·

Connect the cable correctly.

·

Press the MENU button and select BRIGHT and
press the button.

·

Remove the lens cap.

P.8, 26
P.15

P.12

Color is weak and
tint is incorrect

The color and tint have been adjusted
incorrectly.

Adjust the color and tint correctly. P.15

Picture is dark

·

The brightness and contrast has been
adjusted incorrectly.

·

The lamp has not been adjusted.

·

Adjust the brightness and contrast correctly.

·

Replace the lamp with a new one.

P.15

P.28

Picture is not clear

Focus or H.PHASE is not matched. Adjust the focus or H.PHASE P.12, 15

LAMP indicator
lights red.

Trouble with the lamp.

Turn off the power and leave for 45 minutes ;
then turn the power on again.

P.30

TEMP indicator
lights red.

Inside the projector too hot.

·

Do not block the venational holes.

·

Clean the air filter.

·

Use the projector under 35°C temperature.

P.5
P.27

Remote control
mouse cannot be
operated.

·

Cable was connected after the power
was turned on.

·

Video signal not selected.

·Be sure to perform procedure in the following order:
(1)Connect cable. (2)Turn on projector. (3)Turn PC on.

·

Input video signal and select and display input
source.

31

Specifications

All dimensions shown in inches.

∑ All specifications are subject to change without notice.

Dimension diagram

31

Specifications

All dimensions shown in inches.

∑ All specifications are subject to change without notice.

Dimension diagram

31

Specifications

All dimensions shown in inches.

∑ All specifications are subject to change without notice.

Dimension diagram

31

Specifications

All dimensions shown in inches.

∑ All specifications are subject to change without notice.

Dimension diagram

12.6

9.4

4.8

2.9

0.6 (0.4)

Product name Liquid crystal projector
Model name CP-S830W/E
Display system 3 sheets of liquid crystal panels, 3 primary color lights shutter system

Liquid crystal
panel

2.3cm (0.9 inchs)
TFT active matrix

480,000 pixels (V600 X H800)
Lens Zoom lens F=2.0 ~ 2.3 f=38 ~ 50mm
Lamp UHB lamp 150W
Speaker 1W+1W (stereo)
Power supply AC100 ~ 120V, 2.6A/AC220 ~ 240V, 1.3A
Power consumption 230W
Usable temperature range

32 ~ 95∞F

Dimensions (W X H X D)

9.4" X 4.8" (including foot adjuster) X 12.6" (including lens).

9.4" X 5.2" (excluding foot adjuster) X 13.2" (excluding lens).

Weight 11.5 lbs.

Input/Output
terminal

S VIDEO : Mini DIN4-pin terminal

VIDEO : RCA Jack terminal

AUDIO : RCA Jack terminal

RGB signal : D-sub 15pin shrink terminal (Female)

AUDIO : Stereo mini jack

D-sub 15pin shrink terminal (Male)

Accessories

Remote control  1

POWER code  3(CP-S830W)

2(CP-S830E)

BATTERIES (AA or R6P)  2

Panel size
Drive system
Number of pixels

Video signal
input terminal

RGB input/output
signal terminal

Control terminal

-4 ~ 140∞ F

Storage Temperature range

RGB cable  1
MAC adaptor  1
Video/Audio cable 1
Mouse cable  3

12.6

9.4

4.8

2.9

0.6 (0.4)

Product name Liquid crystal projector
Model name CP-S830W/E
Display system 3 sheets of liquid crystal panels, 3 primary color lights shutter system

Liquid crystal
panel

2.3cm (0.9 inchs)

TFT active matrix

480,000 pixels (V600 X H800)
Lens Zoom lens F=2.0 ~ 2.3 f=38 ~ 50mm
Lamp UHB lamp 150W
Speaker 1W+1W (stereo)
Power supply AC100 ~ 120V, 2.6A/AC220 ~ 240V, 1.3A
Power consumption 230W
Usable temperature range

32 ~ 95∞F

Dimensions (W X H X D)

9.4" X 4.8" (including foot adjuster) X 12.6" (including lens).

9.4" X 5.2" (excluding foot adjuster) X 13.2" (excluding lens).

Weight 11.5 lbs.

Input/Output
terminal

S VIDEO : Mini DIN4-pin terminal

VIDEO : RCA Jack terminal

AUDIO : RCA Jack terminal

RGB signal : D-sub 15pin shrink terminal (Female)

AUDIO : Stereo mini jack

D-sub 15pin shrink terminal (Male)

Accessories

Remote control  1

POWER code  3(CP-S830W)

2(CP-S830E)

BATTERIES (AA or R6P)  2

Panel size
Drive system
Number of pixels

Video signal
input terminal

RGB input/output
signal terminal

Control terminal

-4 ~ 140∞ F

Storage Temperature range

RGB cable  1
MAC adaptor  1
Video/Audio cable 1
Mouse cable  3

12.6

9.4

4.8

2.9

0.6 (0.4)

Product name Liquid crystal projector
Model name CP-S830W/E
Display system 3 sheets of liquid crystal panels, 3 primary color lights shutter system

Liquid crystal
panel

2.3cm (0.9 inchs)

TFT active matrix

480,000 pixels (V600 X H800)
Lens Zoom lens F=2.0 ~ 2.3 f=38 ~ 50mm
Lamp UHB lamp 150W
Speaker 1W+1W (stereo)
Power supply AC100 ~ 120V, 2.6A/AC220 ~ 240V, 1.3A
Power consumption 230W
Usable temperature range

32 ~ 95∞F

Dimensions (W X H X D)

9.4" X 4.8" (including foot adjuster) X 12.6" (including lens).

9.4" X 5.2" (excluding foot adjuster) X 13.2" (excluding lens).

Weight 11.5 lbs.

Input/Output
terminal

S VIDEO : Mini DIN4-pin terminal

VIDEO : RCA Jack terminal

AUDIO : RCA Jack terminal

RGB signal : D-sub 15pin shrink terminal (Female)

AUDIO : Stereo mini jack

D-sub 15pin shrink terminal (Male)

Accessories

Remote control  1

POWER code  3(CP-S830W)

2(CP-S830E)

BATTERIES (AA or R6P)  2

Panel size
Drive system
Number of pixels

Video signal
input terminal

RGB input/output
signal terminal

Control terminal

-4 ~ 140∞ F

Storage Temperature range

RGB cable  1
MAC adaptor  1
Video/Audio cable 1
Mouse cable  3

12.6

9.4

4.8

2.9

0.6 (0.4)

Product name Liquid crystal projector
Model name CP-S830W/E
Display system 3 sheets of liquid crystal panels, 3 primary color lights shutter system

Liquid crystal
panel

2.3cm (0.9 inchs)

TFT active matrix

480,000 pixels (V600 X H800)
Lens Zoom lens F=2.0 ~ 2.3 f=38 ~ 50mm
Lamp UHB lamp 150W
Speaker 1W+1W (stereo)
Power supply AC100 ~ 120V, 2.6A/AC220 ~ 240V, 1.3A
Power consumption 230W
Usable temperature range

32 ~ 95∞F

Dimensions (W X H X D)

9.4" X 4.8" (including foot adjuster) X 12.6" (including lens).

9.4" X 5.2" (excluding foot adjuster) X 13.2" (excluding lens).

Weight 11.5 lbs.

Input/Output
terminal

S VIDEO : Mini DIN4-pin terminal

VIDEO : RCA Jack terminal

AUDIO : RCA Jack terminal

RGB signal : D-sub 15pin shrink terminal (Female)

AUDIO : Stereo mini jack

D-sub 15pin shrink terminal (Male)

Accessories

Remote control  1

POWER code  3(CP-S830W)

2(CP-S830E)

BATTERIES (AA or R6P)  2

Panel size
Drive system
Number of pixels

Video signal
input terminal

RGB input/output
signal terminal

Control terminal

-4 ~ 140∞ F

Storage Temperature range

RGB cable  1
MAC adaptor  1
Video/Audio cable 1
Mouse cable  3