Hitachi CP-S335, CP-X340, CP-X345 User Manual

Page 1
1
ENGLISH
Projector
CP-S335/X340/X345
User's Manual – Operating Guide
Thank you for purchasing this projector.
WARNING ►Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference.
About this manual
Various symbols are used in this manual. The meanings of these symbols are described below.
WARNING This symbol indicates information that , if ignored, could possibly
result in personal injury or even death due to incorrect handling.
CAUTION This symbol indicates information that , if ignored, could result
possibly in personal injury or physical damage due to incorrect handling.
Please refer to the pages written following this symbol.
NOTE • The information in this manual is subject to chance without notice.
• The manufacture assumes no responsibility for any errors that may appear in this manual.
• The reproduction, transmission or use of this document or contents is not permitted without express written authority
.
Trademark acknowledgment
• VGA and XGA are registered trademarks of the International Business Machines Corporation.
• Apple and Mac are registered trademarks of the Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of the Microsoft Corporatio
n.
• Internet Explorer is a trademark of the Microsoft Corporation.
All other trademarks are the property of their respective owners.
Page 2
2
About this manual . . . . . . . . . . 1
Contents . . . . . . . . . . . . . . . . . 2
Projector feature
s . . . . . . . . . . 3
Preparation
s . . . . . . . . . . . . . . 3
Part name
s . . . . . . . . . . . . . . . 4
Projector . . . . . . . . . . . . . . . . . . . . . 4
Controls . . . . . . . . . . . . . . . . . . . . . . 5
Remote control . . . . . . . . . . . . . . . . 5
Setting up . . . . . . . . . . . . . . . . 6
Arrangement . . . . . . . . . . . . . . . . . . 7
Adjusting the projector's elevator . . 8 About the filter cover for bottom-up use
. . 9
Connecting your devices . . . . . . . . 10
Connecting power supply . . . . . . . 13
Remote contro
l . . . . . . . . . . . 14
Putting batteries . . . . . . . . . . . . . . 14
Using the remote control . . . . . . . . 15
Power on/of
f . . . . . . . . . . . . . 16
Turning on the powe
r . . . . . . . . . . . 16
Turning off the power . . . . . . . . . . . 16
Operating . . . . . . . . . . . . . . . 17
Adjusting the volume . . . . . . . . . . . 17
Temporarily muting the soun
d . . . . 17
Selecting an input signal . . . . . . . . 17
Searching an input signal . . . . . . . 18
Selecting the aspect ratio . . . . . . . 18
Adjusting the zoom and focus . . . . 18
Using the automatic adjustment feature
. 19
Adjusting the position . . . . . . . . . . 19
Correcting the keystone distortions 19
Using the magnify feature . . . . . . . 20
Freezing the screen . . . . . . . . . . . . 20
Temporarily blanking the scree
n . . 20
Operating the computer screen . . . 21
Multifunctional settings . . . . 22
Using the menu function . . . . . . . . 22
EASY Menu . . . . . . . . . . . . . . . . . . 23
Aspect, Keystone, Mode, Bright, Contrast, Color, Tint, Sharpness, Whisper, Mirror, Reset, Filter time, Language, Go to advanced menu
Contents
Contents
PICTURE Menu . . . . . . . . . . . . . . . 25
Bright, Contrast, Gamma, Color temp, Color, Tint, Sharpness, Progressive, My memory
IMAGE Menu . . . . . . . . . . . . . . . . . 28
Aspect, Over scan, V. position, H. position, H. phase, H. size, Auto adjust
INPUT Menu . . . . . . . . . . . . . . . . . 30
Color space, Component, Video format, Frame lock, Information
SETUP Menu . . . . . . . . . . . . . . . . . 32
Keystone, Whisper, Mirror, Volume
SCREEN Menu . . . . . . . . . . . . . . . 33
Language, Menu position, OSD bright, Blank, Start up, MyScreen, MyScreen lock, Message
OPTION Menu . . . . . . . . . . . . . . . . 36
Search, Auto off, Lamp time, Filter time, Service
Maintenance . . . . . . . . . . . . . 38
Lamp . . . . . . . . . . . . . . . . . . . . . . . 38
Air filte
r . . . . . . . . . . . . . . . . . . . . . 40
Other care . . . . . . . . . . . . . . . . . . . 41
Troubleshootin
g . . . . . . . . . . 42
Related messages . . . . . . . . . . . . . 42
Regarding the indicator lamps . . . . 44
Phenomena that may easily be
mistaken for machine defects . . . . 46
Warranty and after-service
. . . 48
Specification
s . . . . . . . . . . . . 48
Page 3
3
ENGLISH
Projector features / Preparations
Projector features
This projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. It requires just a little space for installation and gets a large image from short distance.
High Brightness
Newly developed 165W UHB (Ultra High Brightness) lamp gives you a higher brightness image on a screen. The image can be still kept as bright and clean enough for use in bright rooms.
Low Noise
WHISPER mode is equipped for reducing acoustic noise to realize quieter operation. It is perfect for use in low luminance rooms where low noise is more important than brightness.
Rich Connectivity
This projector has a variety of I/O ports. It can be easily connected to many signal sources like PC, DVD and so on. The rich connectivity provides you more options to make your presentation impressive.
Compact Body
Even with its many features, this projector is extremely compact and slim, which gives you more flexibility and usability to use it where you want.
Preparations
About contents of package
Please see the "Contents of package" of the "User's manual - Quick guide". Your projector should come with the items shown there. Contact immediately your dealer if anything is missing.
NOTE
• Keep the original packing materials for future reshipment. For
moving the projector, be sure to use the original packing material
. Use special
caution for the lens part.
Page 4
4
Part names
Lens (16)
Lens cover (16) (Slide door)
Filter cover (40) (Air filter and intake vent are inside.)
Elevator button (8)
Elevator foot (8)
Remote sensor (15)
Zoom knob (18) Focus ring (18)
Vent (6)
AC inlet (13)
Power switch (16)
Elevator button (8)
COMPONENT VIDEO ports (12)
Y CB/P
B
CR/P
R
S-VIDEO port (12)
VIDEO port (12)
CONTROL port (11)
Part names
Projector
Lamp cover (Lamp unit is inside.) (38)
Elevator foot (8)
Bottom side
Speaker (6)
Front-Right side
Rear-Left side
Control buttons (See the following page.) (5)
Ports (See below.)
Vent (6)
AUDIO OUT port (11)
Ports
AUDIO IN1 port (11)
AUDIO IN2 port (11) USB port (11)
Restart switch (*) (46) RGB IN1 port (11) RGB IN2 port (11) RGB OUT port (11)
Kensington lock slot
NOTE (*) About Restart switch: This Projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar and before turning on again, make the projector cool down at least 10 minutes without
operating. Only push the Restart switch in these exceptional instances.
Y
VIDEO
AUDIO IN1
RGB IN1
CONTRO
L
RGB IN2 RGB OU
T
AUDIO IN2
AUDIO OU
T
US
B
S-VIDE
O
COMPONENT VIDE
O
CB/PB
CR/PR
Page 5
5
ENGLISH
Part names
LAMP indicator (44) TEMP indicator (44) POWER indicator (16)
STA
NDBY/ON button (16)
Cursor buttons ▲,▼,◄,► (22)
INPUT button
(17)
Remote control
RGB button (17)
VIDEO button (17)
ASPECT button (18)
HOME button (21)
MAGNIFY (20)
ON button OFF button
END button (21)
FREEZE button (20)
POSITION button (19)
Cursor buttons ▲,▼,◄,►(22)
ESC button (22)
SEARCH button (18)
STANDBY/ON button
(16)
AUTO
button (19)
BLANK button (20)
VOLUME button (17)
PAGE UP button
(21)
MUTE button (17)
PAGE DOWN button
(21)
KEYSTONE button
(19)
MENU button (22)
ENTER button (22)
RESET button
(22)
Control buttons
STAN DBY/ ON INP UT
MEN U
POW ER
TE MP
LA MP
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
Page 6
6
Setting up
Setting up
WARNING ►Place the projector in a stable position horizontally. A fall or a turnover could cause an injury and/or damage to the projector. Then using damaged projector could result in a fire and/or an electric shock.
• Don’t place the projector on an unstable, slant or vibrant surface such as a
wobbly or inclined stand.
• Do not place the projector in the side/front/rear-up position, except care of the
air filter.
• For the projector installed bottom-up, use the accessory filter cover for bottom-
up use. And in the case of a ceiling installation or the like, contact your dealer
before installation. ►Place the projection in a cool place, and pay attention enough to ventilation. The high temperature of the projector could cause a fire, a burn and/or malfunction to the projector.
• Don’t stop up, block and cover the projector's vents.
• Keep a space of 30 cm or more between the sides and other objects such as
walls.
• Don’t place the projector on a metallic thing or anything weak in heat.
• Don’t place the projector on a carpet, cushion or bedding.
• Don’t place the projector in direct sunlight or near a hot object such as heater.
• Put nothing about lens and vents of the projector. Put nothing on the projector.
• Put nothing that is sucked or sticks to the bottom of projector. This projector
has some intake vents also on the bottom. ►Do not place the projector on the place that gets wet. Damping the projector or inserting liquid in the projector could cause a fire, an electric shock and/or malfunction to the projector.
• Don’t place the projector in a bathroom or the outdoors.
• Put nothing containing the liquid near the projector.
CAUTION ►Avoid a smoky, humid or dusty place. Placing the projector in such place could cause a fire, an electric shock and/or malfunction to the projector.
• Don’t place the projector near a humidifier, a smoking space or a kitchen.
• Put nothing containing the liquid near the projector. ►Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.
Page 7
7
ENGLISH
(a) Screen size
[inch (m)]
(b) Projection distance [m (inch)] (c) Screen height [cm (inch)]
min. max. down up
30 (0.8) 0.9 (35) 1.1 (42)
5 (2) 41 (16) 40 (1.0) 1.2 (47) 1.4 (56) 6 (2) 55 (22) 50 (1.3) 1.5 (59) 1.8 (71) 8 (3) 69 (27) 60 (1.5) 1.8 (72) 2.2 (85) 9 (4) 82 (32) 70 (1.8) 2.1 (84) 2.5 (100) 11 (4) 96 (38) 80 (2.0) 2.4 (96) 2.9 (114) 12 (5) 110 (43) 90 (2.3) 2.7 (108) 3.3 (129) 14 (5) 123 (49)
100 (2.5) 3.1 (120) 3.6 (143) 15 (6) 137 (54) 120 (3.0) 3.7 (144) 4.4 (172) 18 (7) 165 (65) 150 (3.8) 4.6 (181) 5.5 (216) 23 (9) 206 (81) 200 (5.1) 6.1 (242) 7.3 (288) 30 (12) 274 (108) 250 (6.4) 7.6 (303) 9.2 (361) 38 (15) 343 (135) 300 (7.6) 9.2 (363) 11.0 (433) 46 (18) 411 (162)
(a) Screen size
[inch (m)]
(b) Projection distance [m (inch)] (c) Screen height [cm (inch)]
min. max. down up
30 (0.8) 1.0 (38) 1.2 (46)
-1 (0) 39 (15) 40 (1.0) 1.3 (52) 1.6 (62) -2 (-1) 51 (20) 50 (1.3) 1.6 (65) 2.0 (77) -2 (-1) 64 (25) 60 (1.5) 2.0 (78) 2.4 (93) -2 (-1) 77 (30) 70 (1.8) 2.3 (91) 2.8 (109) -3 (-1) 90 (35) 80 (2.0) 2.7 (105) 3.2 (125) -3 (-1) 103 (41) 90 (2.3) 3.0 (118) 3.6 (140) -4 (-1) 116 (46)
100 (2.5) 3.3 (131) 4.0 (156) -4 (-2) 129 (51) 120 (3.0) 4.0 (158) 4.8 (188) -5 (-2) 154 (61) 150 (3.8) 5.0 (197) 6.0 (235) -6 (-2) 193 (76) 200 (5.1) 6.7 (264) 8.0 (314) -8 (-3) 257 (101) 250 (6.4) 8.4 (330) 10.0 (393) -10 (-4) 322 (127) 300 (7.6) 10.1 (396) 12.0 (472) -12 (-5) 386 (152)
Arrangement
Refer to the illustrations and tables below to determine the screen size and projection distance.
The values shown in the table are calculated for a full size screen: 1280 x 720 (a) The screen size (diagonal) (b) Distance from the projector to the screen (±10%) (c) The height of the screen (±10%)
Setting up
At 16:9 screen
At 4:3 screen
(c) up
(b)
(c) down
4:3
(a)
16:9
(a)
Page 8
8
Adjusting the projector's elevator
WARNING ►Do not adjust the projector’s elevator during use or
immediately after use. Handling while the projector is in a high temperature could cause a burn and/or malfunction to the projector.
CAUTION ►If you press the elevator button without holding the projector, the projector might crash down, overturn, smash your fingers and possibly result in malfunction. To prevent damaging the projector and injuring yourself, always hold the projector whenever using the elevator buttons to adjust the elevator feet. ►Except for inclining by the elevator feet adjustment, place the projector horizontally.
You can use the elevator feet to make adjustments if the surface on which you need to set the projector is uneven or if you otherwise need to adjust the angle of projection. The adjustment range of the elevator feet is 0 to 9 degrees.
1.
After making sure that the projector is cool adequately, press and hold in the elevator buttons while holding the projector.
The elevator buttons and the elevator feet are on the both sides.
2.
Raise or lower the projector to the desired height and the release the elevator buttons.
When you release the elevator buttons, the elevator feet will lock into position.
3.
As necessary, you can also finely adjust the height of the projector by twisting the elevator feet by hand.
Elevator feet
Elevator button
Setting up
Page 9
9
ENGLISH
Setting up
About the filter cover for bottom-up use
WARNING ►Do not replace the filter cover during use or immediately
after use. While the projector connects with a power supply, or the projector is in a high temperature state, handling could cause an electric shock, a fire, a burn and/or malfunction to the projector.Before handling, make sure the power switch is off and the power cord is not plugged in, then wait at least 45 minutes.
When the projector is installed bottom up, please use the accessory filter cover for bottom-up use. It is higher than usual filter cover, to keep the space for intake ventilation. Please change in the following procedure.
1.
After making sure that the projector is cool adequately, slowly turn the projector so that the lens-side is facing up. Please be careful for a projector
not to fall. While the projector is placed lens-side up, hold the projector.
2.
Putting a finger on the filter cover’s knob, slide the filter cover in the direction of the arrow to remove it.
3.
Replace the filter cover for bottom-up use and snap it back into place.
4.
Slowly turn the projector so that the top is facing up.
Filter cover’s knob
To set
Filter cover’s knob
Filter cover
To remove
Filter cover for bottom-up use
Page 10
10
Setting up
Connecting your devices
CAUTION ►Turn off all devices prior to connecting them to the projector.
Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector. ►Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause a certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector. ►Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector.
NOTE • Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer
to the
instruction manual of the corresponding laptop computer.
• Secure the screws on the connectors and tighten.
• Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.
• For some RGB signal modes, the optional Mac adapter is necessary.
• When the image resolution is changed on a computer, depending on an input, automatic adjust function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution.
About Plug-and-Play capability
Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC 2B. Plug-and-Play can be achieved by connecting this projector to computers that are VESA DDC (display data channel) compatible.
• Please take advantage of this function by connecting the accessory RGB cable to the RGB IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.
• Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor.
Page 11
11
ENGLISH
Setting up
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL
RGB IN2 RGB OUT
AUDIO IN2
AUDIO OUT
USB
S-VIDEO
COMPONENT VIDEO
CB/P
B
CR/P
R
Y
VIDEO
AUDIO IN1
RGB IN1
CONTRO
L
RGB IN2 RGB OU
T
AUDIO IN2
AUDIO OUT
USB
S-VIDEO
COMPONENT VIDEO
CB/P
B
CR/P
R
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL
RGB IN2 RGB OUT
AUDIO IN2
AUDIO OUT
USB
S-VIDEO
COMPONENT VIDEO
CB/P
B
CR/P
R
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL
RGB IN2 RGB OUT
AUDIO IN2
AUDIO OUT
USB
S-VIDEO
COMPONENT VIDEO
CB/P
B
CR/P
R
Audio out
USB(A)
RS-232C
RGB out
Examples of connection with a computer
Connecting to a monitor (output)
Connecting to a speaker with amplifier (output)
RGB cable
Stereo mini audio cable
* AUDIO IN1
is linked to
RGB IN1.
RGB out Audio out
Stereo mini audio cable
RGB cable
RGB in
RGB cable
Audio in
Stereo mini
audio cable
USB
cable
RS-232C
cable
Page 12
12
Setting up
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL
RGB IN2 RGB OUT
AUDIO IN2
AUDIO OUT
USB
S-VIDEO
COMPONENT VIDEO
CB/P
B
CR/P
R
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL
RGB IN2 RGB OUT
AUDIO IN2
AUDIO OUT
USB
S-VIDEO
COMPONENT VIDEO
CB/P
B
CR/P
R
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL
RGB IN2 RGB OUT
AUDIO IN2
AUDIO OUT
USB
S-VIDEO
COMPONENT VIDEO
CB/P
B
CR/P
R
Examples of connection with a VCR/DVD player
Audio out
Video
out
Stereo mini audio cable
Video cable
Audio out S-Video out
S-Video cable
Stereo mini audio cable
Stereo mini audio cable
Audio out
Component video out
Component video cable
Y
CB/P
B
CR/P
R
Y
VIDEO
AUDIO IN1
RGB IN1
CONTROL
RGB IN2 RGB OUT
AUDIO IN2
AUDIO OUT
USB
S-VIDEO
COMPONENT VIDEO
CB/P
B
CR/P
R
Stereo mini audio cable
Audio out
Component video out
Component video cable
Y
CB/P
B
CR/P
R
Page 13
13
ENGLISH
Setting up
Connecting power supply
WARNING ►Please use extra caution when connecting the power cord as
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one.
• Only plug the power cord into an outlet rated for use with the power cord's specified voltage range.
• Never modify the power cord. Never attempt to defeat the ground connection of the three-pronged plug.
1.
Connect the connector of the power cord to the AC inlet of the projector.
2.
Firmly plug the power cord's plug into the outlet.
AC inlet
Connector of the power cord
Page 14
14
Remote control
Remote control
Putting batteries
WARNING ►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry play.
• If you observe a leakage of a battery, wipe out the flower and then replace a battery. If the flower adheres your body or clothes, rinse well with water immediately.
1.
Remove the battery cover. Slide back and remove the battery cover in the direction of the arrow.
2.
I
nsert the batteries. Align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control.
3.
Close the battery cover. Replace the battery cover in the direction of the arrow and snap it back into place.
Page 15
15
ENGLISH
Remote control
Using the remote control
CAUTION ►Be careful in handling the remote control.
• Do not drop or otherwise expose the remote control to physical impact.
• Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.
• Remove the batteries from the remote control and store them in a safe place if you won’t be using the remote control for an extended period.
• Replace the batteries whenever the remote control starts to malfunction.
• When strong lights, such as direct sunlight or light from an extremely close range (such as from an inverter fluorescent lamp), hit the projector’s remote sensor, the remote control may cause to function. Adjust the direction of the projector to keep light from directly hitting the projector’s remote sensor.
The remote control works with the projector’s remote sensor.
• The range of the remote sensor is 3 meters with a 60- degree range (30 degrees to the left and right of the remote sensor).
• Also a remote signal reflected in the screen etc. may be available. If it is difficult to send a remote signal to the sensor directly, please try.
• Since the remote control uses infrared light to send signals to the projector (Class1 LED), be sure to use the remote control in an area free from obstacles that could block the remote control’s output signal to the projector.
approx. 3 meters
30º
30º
Page 16
16
Power on/off
Power on/off
WARNING ►When the power is on, a strong light is emitted. Do not look
into the lens or vents of the projector.
NOTE • Turn the power on/off in right order. Please power on the projector
before the connected devices. Power off the projector after the connected devices.
Power switch
STANDBY/ON button
POWER indicator
Turning on the power
1.
Make sure that the power cord is firmly and correctly connected to the projector and outlet.
2.
Open the lens cover, and set the power switch to the
ON position. The power indicator will light to solid orange. Then wait several seconds because buttons may not function for these several seconds.
3.
Press the STANDBY/ON button on the projector or remote control.
The projector lamp will light up and the POWER indicator will begin blinking green. When the power is completely on, the indicator will stop blinking light green.
To display the picture, select an input signal according to the section "Selecting an input signal"
(17)
.
Turning off the power
1.
Press the STANDBY/ON button on the projector or
remote control. The message "Power off?" will appear on the screen for approximately 5 seconds.
2.
Press the STANDBY/ON button on the projector or
remote control again while the message is visible. The projector lamp will go off, and the POWER indicator will begin blinking orange.
Then the POWER indicator will stop blinking and light to solid orange when the lamp cooling is complete.
3.
Make sure that the power indicator lights to solid orange, set the power switch
to the OFF position. The POWER indicator will go off. Close the lens cover.
Power off?
POWER
(Solid orange)
POWER
(Blinking green)
POWER
(Solid green)
POWER
(Blinking orange)
POWER
(Solid orange)
STANDB Y/ON INPU T
MENU
POWE R
TEM P
LAM P
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
Page 17
17
ENGLISH
Operating
Operating
Adjusting the volume
1.
Press the VOLUME button on the remote control.
A dialog will appear on the screen to aid you in adjusting the volume.
2.
Use the cursor buttons ▲/▼ to adjust the volume.
To close the dialog and complete the operation, press the VOLUME button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds.
VIDEO
RG
B
SEARCH
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
ON
MAGNIFY
ASPECT AUTO
BLANK
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
Temporarily muting the sound
1.
Press the MUTE button on the remote control.
A dialog will appear on the screen indicating that you have muted the sound.
To
restore the sound, press the MUTE or VOLUME button. Even if you don’t do anything, the dialog will automatically disappear after a few seconds.
VIDEO
RG
B
SEARCH
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLANK
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
Selecting an input signal
1.
Press the INPUT button on the projector. Each time you press the button, the projector switches its
input port as below. RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO
STANDBY /ON INPUT
MENU
POWER
TEMP
LAMP
1.
Press the RGB button on the remote control to select an
input port for RGB signal. Each time you press the button, the projector switches its RGB input port as below.
RGB IN1  RGB IN2
● When the TURN ON is selected to the item SEARCH of OPTION menu
(36)
, the projector selects the RGB IN1 port at first. If no input is detects at the RGB IN1 port, projector will check the RGB IN2 port.
VIDEO
RG
B
SEARCH
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
ASPECT AUTO
BLANK
1.
Press the VIDEO button on the remote control to select
an input port for video signal. Each time you press the button, the projector switches its video input port as below.
COMPONENT VIDEO
S-VIDEO  VIDEO
● When the TURN ON is selected to the item SEARCH of OPTION menu
(36)
, the projector selects the COMPONENT VIDEO port at first. If no input is detected at the COMPONENT VIDEO port, projector will begin to check other ports.
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
ASPECT AUTO
BLANK
Page 18
18
Operating
Adjusting the zoom and focus
1.
Use the zoom knob to adjust the screen size.
2.
Use the focus ring to focus the picture.
Searching an input signal
1.
Press the SEARCH button on the remote control. The projector will begin to check its input ports in order to
find any input signals. Then when an input is found, the projector will stop
searching and display the image. If no signal is found, the projector will return to the state selected before the operation.
RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
ASPECT AUTO
BLAN
K
Selecting an aspect ratio
1.
Press the ASPECT button on the remote control. Each time you press the button, the projector switches the mode for aspect
ratio in turn.
At a RGB signal
NORMAL  4:3  16:9
At a video signal /no signal
4:3  16:9  SMALL
● The NORMAL mode keeps the original aspect ratio of the signal.
● At a HDTV signal of 1125i (1080i) or 750p (720p) of COMPONENT VIDEO input, only 16:9 mode can be selected.
● Performing the automatic adjustment initializes the aspect ratio setting.
VIDEO
RG
B
SEARCH
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
VOLUME
Zoom knob
Focus ring
Page 19
19
ENGLISH
Operating
Correcting the keystone distortions
1.
Press the KEYSTONE button on the remote control. A dialog will appear on the screen to aid you in
correcting
the distortion.
2.
Use the cursor buttons ▲/▼ to correct the distortion.
To close the dialog and complete this operation, press the KEYSTONE button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds.
● This function may not be work well with some input.
● The adjustable range for correcting will vary among inputs.
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
Using the automatic adjustment feature
1.
Press the AUTO button on the remote control.
At a RGB signal
The vertical position, the horizontal position, the clock phase and horizontal size will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.
At a video signal
The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to the item VIDEO FORMAT of the INPUT menu
(30)
. For a component video signal,
the signal type is identified automatically indep
endently of this function.
● The automatic adjustment operation requires approximately 10 seconds. Also please note that it may not function correctly with some input.
VIDEO
RG
B
SEARCH
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
MAGNIFY
ASPECT AUTO
BLANK
HOME
PAGE UP
VOLUME
Adjusting the position
1.
Press the POSITION button on the remote control. The “POSITION” indication will appear on the screen.
2.
Use the cursor buttons ▲/▼/◄/► to adjust the picture position.
When you want to reset the operation, press the RESET button on the remote control during the operation.
To complete this operation
, press the POSITION button again. Even if you don’t
do anything, the dialog will automatically disappear after a few seconds.
● When this function is performed at a video signal, a certain extra such as a line may appear outside a picture.
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ENTE
R
MENU
Page 20
20
Operating
Freezing the screen
1.
Press the FREEZE button on the remote control. The “FREEZE” indication will appear on the screen, and
the projector will enter the FREEZE mode. To exit the FREEZ
E mode and restore the screen to normal,
press the FREEZE button again.
● The projector automatically exits the FREEZE mode when the input signal changes, or when one of the projector’s buttons or the remote control buttons of STANDBY/ON, SEARCH, RGB, VIDEO, BLANK, AUTO, ASPECT, VOLUME, MUTE, KEYSTONE, POSITION and MENU is pressed.
● If the projector continues projecting a still image for long time, the LCD panel might possibly be printed. Do not leave the projector in FREEZE mode for too long.
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLANK
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
Using the magnify feature
1.
Press the ON button of MAGNIFY on the remote control.
The “MAGNIFY” indication will appear on the screen (although the indication will disappear after several seconds with no operation.), and the projector will enter the MAGNIFY mode.
2.
Use the cursor buttons ▲/▼ to adjust the zoom level.
To move the zoom area
, press the POSITION button in the MAGNIFY mode, then use the cursor buttons ▲/▼/◄/► to move the area. And to finalize the zoom area, press the POSITION button again.
To exit the MAGNIFY mode and restore the screen to normal, press the O
FF
button of MAGNIFY on the remote control.
● The projector automatically exits the MAGNIFY mode when the input signal changes, or when an operation of changing the display condition (automatic adjustment, etc.) is executed.
● Although in the MAGNIFY mode, the keystone distortion condition may vary, it will be restored when the projector exit the MAGNIFY mode.
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
OFF
ON
MAGNIFY
ASPECT AUTO
BLANK
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
Temporarily blanking the screen
1.
Press the BLANK button on the remote control.
The blank screen will be displayed instead of the screen of input signal. Please refer to the item BLANK of section SCREEN menu
(33).
To remove the blank screen and return to the input signal screen, press the BLANK button again.
● The projector automatically returns to the input signal screen when the input signal changes, or when one of the projector’s buttons or the remote control buttons are pressed.
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARC
H
STANDBY/ON
MAGNIFY
ASPECT AUTO
BLANK
HOME
PAGE UP
VOLUME
Page 21
21
ENGLISH
Operating
Operating the computer screen
CAUTION ►Mistaken use of the mouse/keyboard control could damage
your equipment.
• While using this function, please connect only with a computer.
• Before connecting, read the manuals of the computer you will connect.
NOTE • It may not be possible to control notebook PC, and other computers with built-in pointing device (e.g. track ball), using this remote control. In this case, before connecting go into BIOS (system setup) and select external mouse, and disable the pointing device. In addition, the mouse may not function if the computer does not have the needed utility program. See your computer’s hardware manual for details.
• The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to use the remote control, depending on the computer’s configurations and mouse drivers.
• The USB control can be used only for the functions listed below. You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).
• This function is not available while the lamp is warming up (the POWER indicator flashes green), and while adjusting the volume and display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu
screen.
USB mouse and keyboard control
1.
Connect the projector’s USB port to the computer via the mouse cable.
Available function Remote control operation
Move pointer Use ▲, ▼, ◄, ► buttons
Left click with mouse Press ENTER button
Right click with mouse Press RESET button
Press keyboard’s HOME key
Press HOME button
Press keyboard’s END key
Press END button
Press keyboard’s PAGE UP key Press PAGE UP button
Press keyboard’s PAGE DOWN key Press PAGE DOWN button
Press keyboard’s ESC key
Press ESC button
Page 22
22
Multifunctional settings
Multifunctional settings
Using the menu function
This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, OPTION and EASY MENU. Each of these menus is operated using the same methods. The basic operations of these menus are as follows.
1.
Press the MENU button on the remote control or one of the cursor buttons on the projector.
The advanced MENU or EASY MENU will appear
.
2.
Use the cursor buttons ▲/▼ to select a menu.
At the EASY MENU
If you want to change it to the advanced MENU, select the "Go to Advanced Menu".
At the advanced MENU
Select a menu of PICTURE, IMAGE, INPUT, SETUP, SCREEN or OPTION. If you want to change it to the EASY MENU, select the EASY MENU.
3.
Then press the cursor button ► on the projector or remote
control, or the ENTER button on the remote control to progress. The display of the selected menu will be active.
4.
Use the cursor buttons ▲/▼ to select an item to operate.
Then press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. The operation menu of the selected item will appear.
5.
Use the cursor buttons▲/▼ to operate the item.
When you want to reset the operation, press the RESET button on the remote control during the operation. Note that items whose functions are performed simultaneously with operation (ex. LANGUAGE, H PHASE etc.) aren't reset.
When you want to return to the previous display, press the cursor b
utton ◄ on
the projector or remote control, or the ESC button on the remote control.
6.
Press the MENU button on the remote control again to close the menu and
complete this operation. Even if you don't do anything, the dialog will automatically disappear after about 10 seconds.
MENU [RGB
]
:SELECT
PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN
U
BRIGHT CONTRAS
T GAMMA COLOR TEMP COLOR TINT SHARPNES
S PROGRESSIVE MY MEMORY
+0 +0
#1 DEFAUL
T
LOW
+0 +0 +0
TURN OFF
SAVE 1
Advanced MENU
EASY MENU
ASPECT KEYST
ONE MODE BRIGHT CONTRAST COLO
R TINT SHRPNESS WHISPER MIRROR RESE
T FILTER TIME LANGUAGE
4:3
+0
NORMAL +0 +0 +0 +0 +3
NORMAL
NORMAL
EXECUTE
0
ENGLISH
Go To Advance Menu...
EASY MENU
VIDEO
RG
B
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
RESET button
ENTER button
MENU button
Cursor buttons
STAND BY/O N INPU T
MENU
POWE R
TEM P
LAM P
VIDEO
RGB
SEARC
H
STANDBY/ON
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
HOME
PAGE UP
PAGE DOWN
END
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
Page 23
23
ENGLISH
Multifunctional settings
EASY Menu
Item Description
ASPECT
Using the buttons ◄/► switches the mode for aspect ratio. See the item ASPECT of section IMAGE menu
(28).
KEYSTONE
Using the buttons ◄/► corrects the keystone distortion. See the item KEYSTONE of section SETUP menu (32).
MODE
Using the buttons ◄/► switches the mode of picture type.The modes of picture type are combinations of a mode of GAMMA and a mode of COLOR TEMP. Choose a suitable mode according to the projected source.
NORMAL
CINEMA
DYNAMIC
NORMAL: (COLOR TEMP = MIDDLE) + (GAMMA = #1 DEFAULT) CINEMA: (COLOR TEMP = LOW) + (GAMMA = #2 DEFAULT) DYNAMIC: (COLOR TEMP = HIGH) + (GAMMA = #3 DEFAULT)
• When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the MODE is “CUSTOM”. Please refer to the items GAMMA
(25) and
COLOR TEMP
(26) of PICTURE menu.
BRIGHT
Using the buttons ◄/► adjusts the brightness. See the item BRIGHT of section PICTURE menu (25).
CONTRAST
Using the buttons ◄/► adjusts the contrast. See the item CONTRAST of section PICTURE menu (25).
COLOR
Using the buttons ◄/► adjusts the strength of whole color. See the item COLOR of section PICTURE menu (26).
TINT
Using the buttons ◄/► adjusts the tint. See the item TINT of section PICTURE menu (26).
With the EASY MENU, items shown in the table below can be performed.
Select an item using the cursor buttons ▲/▼ on the projector or remote control. Then perform it referring to the following table.
EASY MENU
ASPECT KEYST
ONE MODE BRIGHT CONTRAS
T
COLO
R TINT SHRPNESS WHISPER MIRROR RESE
T FILTER TIME LANGUAGE
4:3
+0
NORMAL +0 +0 +0 +0 +3
NORMAL
NORMAL
EXECUTE
0
ENGLISH
Go To Advance Menu...
Page 24
24
Multifunctional settings
Item Description
SHARPNESS
Using the buttons ◄/► adjusts the sharpness. See the item SHARPNESS of section PICTURE menu (26).
WHISPER
Using the buttons ◄/► turns off/on the whisper mode. See the item WHISPER of section SETUP menu (32).
MIRROR
Using the buttons ◄/► switches the mode for mirror status. See the item MIRROR of section SETUP menu (32).
RESET
Performing this item resets all of the items of EASY MENU except FILTER TIME and LANGUAGE. A dialog is displayed to make sure. Selecting RESET using the button ▲ performs reset.
FILTER TIME
Performing this item resets the filter timer which counts use time of air filter. A dialog is displayed to make sure. Selecting RESET using the button ▲ performs reset. See the item FILTER TIME of section OPTION menu (37).
LANGUAGE
Select the LANGUAGE to toggle the menu language. Refer to description of LANGUAGE in the SCREEN menu (33).
Go To
Advanced Menu
Select the “Go To Advanced Menu” to use the
menu of PICTURE,
IMAGE, INPUT, SETUP, SCREEN or OPTION.
EASY Menu (continued)
Page 25
25
ENGLISH
Multifunctional settings
PICTURE Menu
Item Description
BRIGHT Using the buttons ▲/▼ adjusts the brightness. : Light  Dark
CONTRAST Using the buttons ▲/▼ adjusts the contrast. : Strong
Weak
GAMMA
Using the buttons ▲/▼ switches the GAMMA mode. :
#1 DEFAULT
#1 CUSTOM  #2 DEFAULT
#3 CUSTOM
 #3 DEFAULT  #2 CUSTOM
To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM
Selecting a mode of CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones.
Choose an item using the buttons ◄/►, and adjust the level using the buttons ▲/▼.
You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.
No pattern  Gray scale of 9 steps Ramp  Gray scale of 15 steps Eight of equalizing bars corresponds to eight of tone level of test
pattern except the darkest in the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalizing adjustment bar “1”. The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar.
With the PICTURE menu, items shown in the table below can be performed.
Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table.
MENU [RGB
]
:SELECT
PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN
U
BRIGHT CONTRAS
T GAMMA COLOR TEMP COLOR TINT SHARPNES
S PROGRESSIVE MY MEMOR
Y
+0 +0
#1 DEFAUL
T
LOW
+0 +0 +0
TURN OFF
SAVE
1
1
+0
2
+0
3
+0
4
+0
5
+0
6
+0
7
+0
8
+0
GAMMA [CUSTOM 1
]
ENTER :
Page 26
26
Multifunctional settings
Item Description
COLOR TEMP
Using the buttons ▲/▼ switches the mode of color temperature.
HIGH  MIDDLE  LOW
CUSTOM
To adjust CUSTOM
Selecting the CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the OFFSET and/or GAIN of CUSTOM mode.
OFFSET adjustments change the color intensity on the whole tones of the test pattern.
GAIN adjustments mainly affect color intensity on the brighter tones of the test pattern.
Choose an item using the buttons ◄/►, and adjust the level using the buttons ▲/▼.
You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.
No pattern  Gray scale of 9 steps Ramp  Gray scale of 15 steps
COLOR
Using the buttons ▲/▼ adjusts the strength of whole color.
Strong
Weak
• This item can be selected only at a video signal.
TINT
Using the buttons ▲/▼ adjusts the tint.
Green  Red
• This item can be selected only at a video signal except for SECAM.
SHARPNESS
Using the buttons ▲/▼ adjusts the sharpness.
Strong
Weak
PICTURE Menu (continued)
R
+0
G
+0
B
+0
COLOR TEMP
ENTER :
OFFSET
R
+0
G
+0
B
+0
GAIN
Page 27
27
ENGLISH
Multifunctional settings
Item Description
PROGRESSIVE
Using the buttons ▲/▼ switches the progressive mode.
TV  FILM  TURN OFF
• This function performs only at an interlaced signal of a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input of 525i (480i) or 625i (576i) signal.
• When the TV or FILM is selected, the screen image will be crisper. The FILM mode is adaptable to the 2-3 Pull-Down system to the conversion. But these may cause a certain defect (for example, jagged line) of the picture at a quick moving object. In such a case, please select the TURN OFF, even though the screen image may lose the crisp.
MY MEMORY
Selecting a mode of MY MEMORY using the buttons ▲/▼ and then pressing the button ► or the ENTER button performs each function.
LOAD1  LOAD2  LOAD3  LOAD4
SAVE4
SAVE3  SAVE2  SAVE1
This projector has 4 numbered memories for adjustment data. Performing the LOAD1, LOAD2, LOAD3 or LOAD4 loads the data on the memory whose number corresponds with the command’ s number, and adjusts the picture automatically depending on the data. Performing the SAVE1, SAVE2, SAVE3 or SAVE4 puts the current adjustment data on the memory whose number corresponds with the command’s number.
PICTURE Menu (continued)
Page 28
28
Multifunctional settings
IMAGE Menu
Item Description
ASPECT
Using the buttons ▲/▼ switches the mode for aspect ratio. At a RGB signal
4:3  16:9  NORMAL
At a video signal / no signal
4:3  16:9  SMALL
• The NORMAL mode keeps the original aspect ratio of the signal.
• At a HDTV signal of 1125i (1080i)
or 750p (720p) of COMPONENT
VIDEO input, this item can't be selected.
• Performing the automatic adjustment initializes the aspect ratio setting.
OVER SCAN
Using the buttons ▲/▼ adjusts the over-scan ratio.
Large (It reduces picture)  Small (It magnifies picture)
• This item can be selected only at a video signal.
• When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case, please adjust small.
V POSITION
Using the buttons ▲/▼ adjusts the vertical position.
Up  Down
H POSITION
Using the buttons ▲/▼ adjusts the horizontal position.
Left  Right
H PHASE
Using the buttons ▲/▼ adjusts the horizontal phase to eliminate flicker.
Right  Left
• This item can be selected only at a RGB signal or a component video signal.
With the IMAGE menu, items shown in the table below can be performed.
Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table.
MENU [RGB
]
:SELECT
PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN
U
ASPEC
T OVER SCAN V POSITION H POSITION H PHAS
E H SIZE AUTO ADJUST
4:3 95 25 142 16 1344
Page 29
29
ENGLISH
Multifunctional settings
Item Description
H SIZE
Using the buttons ▲/▼ adjusts the horizontal size.
Large  Small
• This item can be selected only at a RGB signal.
• When this adjustment is excessive, the picture may not be displayed correctly. In such a case, please reset the adjustment pressing the RESET button on the remote control during this operation.
AUTO ADJUST
Selecting this item performs the automatic adjustment feature.
At a RGB signal
The vertical position, the horizontal position, the clock phase and horizontal size will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.
At a video signal
The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to the item VIDEO FORMAT of INPUT menu. For a component video signal, the signal type is identified automatically independently of this function.
• The automatic adjustment operation requires approximately 10 seconds. Also please note that it may not function correctly with some input.
IMAGE Menu (continued)
Page 30
30
Multifunctional settings
INPUT Menu
Item Description
COLOR SPACE
Using the buttons ▲/▼ switches the mode for color space.
AUTO
RGB  SMPTE240  REC709  REC601
This item can be selected only at a RGB signal or a component video signal.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a case, it might be good to select the SMPTE240 or the REC709.
COMPONENT
Using the buttons ▲/▼ switches the function of COMPONENT VIDEO port.
COMPONENT
SCART RGB
When the SCART RGB is selected, the COMPONENT VIDEO port function as a port for a SCART RGB signal input. A SCART adapter and SCART cable realize a SCART RGB input to the projector. For details, ask your dealer.
VIDEO FORMAT
Using the buttons ▲/▼ switches the mode for video format.
AUTO
NTSC
PAL
SECAM
N-PAL  M-PAL  NTSC4.43
• This item performs only at a video signal from the VIDEO port or the S-VIDEO port. For a component video signal, the signal type is identified automatically independently of this function.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. If the picture becomes unstable (ex. an irregular picture, a color lack), please select the mode depending on the input signal.
FRAME LOCK
Using the buttons ▲/▼ turns the frame lock function on/off.
TURN ON  TURN OFF
• This item performs only at a RGB signal with vertical frequency of 50 to 60 Hz for the models CP-X340 and CP-X345, or 50 to 72Hz for the model CP-S335.
• When the TURN ON is selected, a moving picture is displayed more smoothly.
• This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF.
With the INPUT menu, items shown in the table below can be performed.
Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table.
MENU [RGB
]
:SELECT
PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN
U
COLOR SPAC
E COMPONENT VIDEO FORMA
T FRAME LOCK INFORMA
TION
AUT
O COMPONENT AUT
O TURN ON
Page 31
31
ENGLISH
Multifunctional settings
INPUT Menu (continued)
Item Description
INFORMATION
Selecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.
INPUT-INFORMATION
RGB
1024x768 @60.0
FRAME LOCK
INPUT-INFORMATION
S-VIDEO
SECAM
AUTO
INPUT-INFORMATION
COMPONENT
576i @50
SCART RGB
• The “FRAME LOCK” message on the dialog means the frame lock function is working (30).
• The “SCART RGB” message means the COMPONENT VIDEO port is working as a SCART RGB input port. Please refer to the item COMPONENT in this section.
(30)
• This item is can't be selected at no signal.
Page 32
32
Multifunctional settings
SETUP Menu
Item Description
KEYSTONE
Using the buttons ▲/▼ corrects the keystone distortion.
Upper in the data  Lower in the data
• The adjustable range of this function will vary with the type of input signal. At some signals, this function may not work well.
• When the V:INVERT or the H&V:INVERT is selected under the item MIRROR, if the projector screen is inclined or if the projector is angled downward, this function may not work correctly.
• When the zoom adjustment is set to the TELE side, this correction may be excessive. This function should be used with zoom set to WIDE whenever possible.
WHISPER
Using the buttons ▲/▼ turns off/on the whisper mode.
NORMAL
WHISPER
• When the WHISPER is selected, acoustic noise and screen brightness are reduced.
MIRROR
Using the buttons ▲/▼ switches the mode for mirror status.
NORMAL
H:INVERT  V:INVERT  H&V:INVERT
VOLUME
Using the buttons ▲/▼ adjusts the volume.
High  Low
With the SETUP menu, items shown in the table below can be performed.
Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table.
MENU [RGB
]
:SELECT
PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN
U
KEYST
ONE WHISPER MIRROR VOLUM
E
+0 NORMAL NORMAL 16
Page 33
33
ENGLISH
Multifunctional settings
SCREEN Menu
Item Description
LANGUAGE
Using the buttons ▲/▼ switches the OSD (On Screen Display) language.
ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO
NORSK NEDERLANDS PORTUGUÊS
SVENSKA SUOMI POLSKI
MENU POSITION
Using the buttons ◄/►/▲/▼ adjusts the menu position. To quit the operation, press the MENU button on the remote control or keep no operation for 10 seconds.
OSD BRIGHT
Using the buttons ▲/▼ switches the brightness level of the OSD (On Screen Display).
Bright  Dark
BLANK
Using the buttons ▲/▼ switches the mode the blank screen. The blank screen is the screen for the temporarily blanking feature (20). It is displayed by pressing the BLANK button on the remote control.
MyScreen
ORIGINAL
BLUE  WHITE  BLACK
MyScreen is the screen you can register a desired screen. ORIGINAL screen is the existing standard screen.
BLUE, WHITE
and BLACK are non-patterned (plain) screens in each color.
• To avoid remaining as an afterimage, the MyScreen and the ORIGINAL screens will change to the BLACK screen after several minutes.
• For the MyScreen, please refer to the item MyScreen (34).
With the SCREEN menu, items shown in the table below can be performed.
Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table.
MENU [RGB
]
:SELECT
PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN
U
LANGUAGE MENU POSITION OSD BRIGHT BLANK START UP MyScreen MyScreen Lock MESSAGE
ENGLISH
5 BLACK ORIGINA
L
TURN OFF TURN ON
Page 34
34
Multifunctional settings
Item Description
START UP
Using the buttons ▲/▼ switches the mode the start up screen. The start up screen is the screen displayed when no signal or an unsuitable signal is detected.
MyScreen
ORIGINAL  TURN OFF
MyScreen is the screen you can register a desired screen. ORIGINAL screen is the existing standard screen. When the TURN OFF is selected, the BLUE screen is used.
• To avoid remaining as an afterimage, the MyScreen and the ORIGINAL screens will change to the BLANK screen after several minutes. If also the BLANK screen is the MyScreen or ORIGINAL, it will change to the BLACK screen.
• For the MyScreen, please refer to the item MyScreen
below
. About the BLUE, BLACK and BLANK screens, please refer to the item BLANK (33).
My Screen
This item functions for capturing the MyScreen of the blank screen and the start up screen. Please execute displaying the input including the picture you want to capture.
1. Selecting this item displays a dialog titled “MyScreen”. It will ask
you if you start capturing the picture from the current screen. Please wait for the target picture to be displayed, and press the ENTER button on the remote control when the picture is display. The picture will freeze and the frame for capturing appears.
To stop performing, press the RESET or ESC button on the
remote control.
2. Using the buttons ◄/►/▲/▼ adjust the frame position. Please
move the frame to the position of the picture which you want to use.
To start registration, press the ENTER button on the remote
control.
To restore the screen and return to the previous dialog, press the
RESET or ESC button on the remote control.
Registration takes several minutes. When the registration is completed, the registered screen and the message “MyScreen registration is finished.” are displayed for several seconds. If the registration failed, the message “A capturing error has occurred. Please try again.” is displayed.
My Screen Lock
Using the buttons ▲/▼ turns on/off the MyScreen lock function.
TURN ON
TURN OFF
When the TURN ON is selected, the item MyScreen cannot be performed. Use this function for protecting the current MyScreen.
SCREEN Menu (continued)
Page 35
35
ENGLISH
Multifunctional settings
Item Description
MESSAGE
Using the buttons ▲/▼ turns on/off the message function.
TURN ON
TURN OFF
When the TURN ON is selected, the following message function works.
“AUTO IN PROGRESS” while automatically adjusting ”NO INPUT IS DETECTED” ”SYNC IS OUT OF RANGE”
”Searching ....” while searching for an input signal
”Detecting….” when an input signal is detected The indication of the input signal by changing The indication of the aspect ration by changing .
SCREEN Menu (continued)
Page 36
36
Multifunctional settings
OPTION Menu
Item Description
SEARCH
Using the buttons ▲/▼ turns on/off the message function.
TURN ON
TURN OFF
When the TURN ON is selected, detecting no signal automatically cycles through input ports in order of following. Then when an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state before the operation.
RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO
AUTO OFF
Using the buttons ▲/▼ adjusts the time to count down to automatically turn the projector off
.
Long (max. 99 minutes)  Short (min. 0 minute = DISABLE)
AUTO OFF
ENABL
E
1
AUTO OFF
DISABLE
0
When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with a no-signal or an unsuitable signal reaches at the set time, the projector lamp will go off and the power indicator begins blinking. Please refer to the section “Turning off the power” (16).
LAMP TIME
The lamp time is the time counted after the last resetting. It is shown in the OPTION menu as the use time of the lamp. Pressing the RESET button on the remote control for about 3 seconds displays a dialog. To reset the lamp time, select the RESET using the button ▲.
RESET
CANCEL
• Please reset the lamp time only when you have replaced the lamp, for correct messages about the lamp.
• About the lamp replacement, please see the section "Lamp" (
38, 39).
With the OPTION menu, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress, except for the items LAMP TIME and FILTER TIME. Then perform it referring to the following table.
MENU [RGB
]
:SELECT
PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN
U
SEARC
H
AUT
O OFF LAMP TIME FILTER TIME SERVICE
TURN ON
0 0 0
Page 37
37
ENGLISH
Multifunctional settings
Item Description
FILTER TIME
The filter time is the time counted after the last resetting. It is shown in the OPTION menu as the use time of the air filter. Pressing the RESET button on the remote control for about 3 seconds displays a dialog. To reset the filter time, select the RESET using the button ▲.
RESET
CANCEL
• Please reset the filter time only when you have cleaned or replaced the air filter, for correct messages about the air filter.
• About the caring the air filter, please see the section "Air filter" (
40).
SERVICE
Selecting this item displays the SERVICE menu. Select an item using the buttons ▲/▼, and press the button ► or the ENTER button on the remote control to progress.
FAN SPEED
FACTORY RESET  GHOST
FAN SPEED
Using the buttons ▲/▼ switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc.
Note that the
projector is noisier when the HIGH is selected.
HIGH  NORMAL
GHOST
1. Select a color element of ghost using the buttons ▲/▼ and press the cursor button ► or the ENTER button on the remote control to progress.
2. Adjust the selected element using the buttons ▲/▼ to disappear
ghost.
FACTORY RESET
Selecting RESET using the button ▲ performs this function.
By this function, all the items in all of menu will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME and LANGUAGE are not reset.
RESET
CANCEL
OPTION Menu (continued)
Page 38
38
Maintenance
Maintenance
Lamp
WARNING
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.
About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws. For lamp recycling, go to www.lamprecycle.org. (in the US) For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, call your dealer.
• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.
• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.
• Use only the lamp of the specified type.
• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.
Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• If the indicators or a message prompts you to replace the lamp (see the section "Related Messages" and "Regarding the indicator Lamps"), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.
Disconnect
the plug from the
power
outlet
Page 39
39
ENGLISH
Lamp (continued)
When the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible.
1.
Turn the projector off, and unplug the power cord. Allow the lamp to cool for at least 45 minutes.
2.
To prepare a new lamp, contact your dealer and tell the lamp type number = DT00671. If the projector is mounted on the ceiling, or if the lamp has
broken, also ask the dealer to replace the lamp.
In the case of replacement by yourself,
3.
After making sure that the projector has cooled adequately, slowly turn over the
projector, so that the bottom is facing up.
4.
Please unhook the claws of the lamp cover using a minus screwdriver or similar, and
remove the lamp cover.
5.
Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the
handles.
6.
Insert the new lamp, and retighten firmly two screws that are loosened in the previous
process to lock it in place.
7.
Interlocking the 2 tabs of the lamp cover to the projector,
position the lamp cover on the
projector. Then push the
center point of two
claws to fix the lamp cover
.
8.
Slowly turn the projector so that the top is facing up.
9.
Turn the projector on, and reset the lamp time using the LAMP TIME function of OPTION
menu
(36)
.
NOTE • When the lamp has been replaced after the message of "THE POWER WILL TURN OFF AFTER 0hr." is displayed, complete the following operation within 10 minutes of switching power on.
• Incorrectly resetting of the lamp timer (resetting without replacement, or
neglect of resetting after replacement) will result in incorrect message functions.
Maintenance
Lamp cover
Claws
Screws marked
by arrow
Center point of claws
Tabs
Claws
Page 40
40
Maintenance
When the indicators or a message prompts you to clean the air filter, clean the air filter as soon as possible
. If the air filter becomes clogged by dust or the like, internal temperatures
rise and the power may be automatically turned off for malfunction prevention.
1.
Turn the projector off, and unplug the power cord. Allow the projector to cool for at least 45 minutes. And
prepare a vacuum cleaner.
2.
After making sure that the projector is cool adequately,
slowly turn the projector so that the lens-side is facing up. Please be careful for a projector not to fall. While the projector is placed lens-side up, hold the projector.
3.
Putting a finger on the filter cover’s knob, slide the
filter cover in the direction of the arrow to remove it
.
4.
Holding the air filter’s knob, pull the air filter off.
5.
Apply a vacuum cleaner to the vent of the projector for the
air filter. And then slowly turn the projector bottom up
.
6.
Apply a vacuum cleaner to the air filter and filter cover.
Please replace the air filter when it is damaged or too soiled. To prepare a new air filter, contact your dealer and tell the air filter type number
= NJ09702.
An air filter of specified type will come even with the replacement lamp for this projector.
7.
Position the cleaned air filter or a new air filter into place, and push the points
of "PUSH" word with claws to fix the air filter.
8.
Replace the filter cover and snap it back into place.
9.
Slowly turn the projector so that the top is facing up.
10.
Turn the projector on, and reset the filter time using the FILTER TIME function of OPTION menu
(37)
.
NOTE
• Incorrectly resetting of the filter timer (resetting without replacement,
or neglect of resetting after replacement) will result in incorrect message
functions.
Filter cover’s knob
Filter cover
Air filter
Air filter’s knob
WARNING ►Before caring, make sure the power switch is off and the power cable is not plugged in, then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. ►Use only the air filter of the specified type. Do not use the projector with the air filter and filter cover removed. ►Avoid wetting the projector or inserting liquids in the projector. It could result in a fire, an electric shock, and and/or malfunction to the projector
.
CAUTION ►Please replace the air filter when it is damaged or too soiled, and also when you replace the lamp.
Air filter
Page 41
41
ENGLISH
Maintenance
WARNING ►Before caring, make sure the power switch is off and the
power cable is not plugged in, and then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. ►Never try to care for the inside of the projector personally. Doing is so dangerous. ►Avoid wetting the projector or inserting liquids in the projector. It could result in a fire, an electric shock, and and/or malfunction to the projector.
• Don’t put a container containing water, cleaner or chemicals near the projector.
• Don’t use aerosols or sprays.
CAUTION ►Please take right care of the projector according to the following. Incorrect care could cause not only an injury but adverse influence such as discoloration, peeling paint, etc.
• Do not use cleaner or chemicals other than those listed below.
• Do not polish or wipe with hard objects.
Inside of the projector
In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every 2 years.
Caring for the lens
If the lens is flawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of the handling.
1.
Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently
.
2.
After making sure that the projector is cool adequately, lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens
directly with your hand.
Caring for the cabinet and remote control
Incorrect care could have adverse influence such as discoloration, peeling paint, etc.
1.
Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.
2.
After making sure that the projector is cool adequately, lightly wipe with gauze
or a soft cloth. If soiling is severe, dip soft cloth in water or a neutral cleaner dilute in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.
Other care
Page 42
42
Troubleshooting
Troubleshooting
Related messages
When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below.
If the same message is displayed after the treatment, or if a message other than the following appears, please contact your dealer or service company.
Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.
Message Description
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
The time the lamp timer has counted is approaching 2000 hours.
Preparation of a new lamp, and an early lamp change is recommended. After you have change the lamp, please be sure to reset the lamp timer (36).
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER ** hr.
The time the lamp timer has counted is approaching 2000 hours, so a lamp change within ** hours is recommended.
When lamp usage reaches 2000 hours, the power will automatically be turned off. Please change the lamp by referring to the section “Lamp”. After you have changed the lamp, please be sure to reset the lamp timer (36).
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER 0 hr.
As the time the lamp timer has counted has reached 2000 hours, the power will soon be automatically turned off.
Please immediately turn the power off, and change the lamp by referring to the section “Lamp”. After changing the lamp, please be sure to reset the lamp timer (36).
NO INPUT IS DETECTED
ON ***
There is no input signal.
Please confirm the signal input connection, and the status of the signal source.
SYNC IS OUT OF RANGE
ON *** fH *****kHz fV *****Hz
The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit.
Please confirm the specs for this unit or the signal source specs.
CHECK THE AIR FLOW
The internal portion temperature is rising.
Please turn the power OFF, and allow the unit to cool down at least 20 minutes. After having confirmed the following items, please turn the power ON again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the treatment, please set the
HIGH at the FAN SPEED of the item SERVICE of the OPTION menu.
Page 43
43
ENGLISH
Troubleshooting
Related messages (continued)
Message Description
CLEAN THE AIR FILTER
POWER OFF FIRST,
THEN CLEAN THE AIR
FILTER.
AFTER CLEANING THE AIR
FILTER,
RESET THE FILTER TIMER.
A note of precaution when cleaning the air filter.
Please immediately turn the power OFF, and clean or change the air filter by referring to the “Air Filter” section of this manual. After you have cleaned or changed the air filter, please be sure to reset the filter timer
(37).
NOTE • A lamp has a finite product life. Lamps are characterized by the fact that, after long hours of usage, a lamp will no longer light up, or the lamp will break or burst, etc. This projector is equipped with an automatic shut-down function, such that the power will automatically be turned off when lamp usage time has reached 2000 hours. Please be aware, however, that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the functioning of the automatic shut-down function of this projector.
Page 44
44
Troubleshooting
Regarding the indicator lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table. If the same indication is displayed after the treatment, or if an indication other than the following is displayed, please contact your dealer or service company.
POWER
indicator
LAMP
indicator
TEMP
indicator
Description
Lighting
In Orange
Turned
off
Turned
off
The projector is in a standby state.
Please refer to the section “Power On/Off”.
Blinking
In Green
Turned
off
Turned
off
The projector is warming up.
Please wait.
Lighting
In Green
Turned
off
Turned
off
The projector is in an on state.
Ordinary operations may be performed.
Blinking
In Orange
Turned
off
Turned
off
The projector is cooling down.
Please wait.
Blinking
In Red
(discre­tionary)
(discre­tionary)
The projector is cooling down. A certain error has been detected.
Please wait until the POWER indicator finishes blink, and then perform the proper response measure using the item descriptions below as reference.
Blinking
In Red
or
Lighting
In Red
Lighting
In Red
Turned
off
The lamp does not light, and there is a possibility that interior portion has become heated.
Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the treatment, please change the lamp by referring to the section “Lamp”.
Blinking
In Red
or
Lighting
In Red
Blinking
In Red
Turned
off
The lamp cover has not been properly fixed (attached).
Please turn the power off, and allow the unit to cool down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp cover. After performing any needed maintenance, turn the power on again. If the same indication is displayed after the treatment, please contact your dealer or service company.
Page 45
45
ENGLISH
Troubleshooting
Regarding the indicator lamps (continued)
POWER
indicator
LAMP
indicator
TEMP
indicator
Description
Blinking
In Red
or
Lighting
In Red
Turned
off
Blinking
In Red
The cooling fan is not operating.
Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation that no foreign matter has become caught in the fan, etc., and then turn the power on again. If the same indication is displayed after the treatment, please contact your dealer or service company.
Blinking
In Red
or
Lighting
In Red
Turned
off
Lighting
In Red
There is a possibility that the interior portion has become heated.
Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the treatment, please set the HIGH at the FAN SPEED of the item SERVICE of the OPTION menu.
Lighting
In Green
Alternative
blinking in Red
There is a possibility that the interior portion has become overcooled.
Please use the unit within the usage temperature parameters (5°C to 35°C). After the treatment, resent the power to ON.
Lighting
In Green
Simultaneous
blinking in Red
It is time to clean the air filter.
Please immediately turn the power OFF, and clean or change the air filter by referring to the section “Air Filter”. After cleaning or changed the air filter, please be sure to reset the filter timer. After the treatment, resent the power to ON.
NOTE • When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off
. In such a case, press the “” (OFF) side of the power switch, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp
cover, and then turn the power on again.
Page 46
46
Troubleshooting
Phenomena that may easily be mistaken for machine defects
WARNING ►Never use the projector if abnormal operations such as
smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet After making sure that the smoke or odor has stopped, contact your dealer or service company.
1.
Before requesting repair, please check in accordance with the following chart. This operation sometimes resolves your problem.
If the situation cannot be corrected,
2.
The projector’s microprocessor may need to be reset. Please push the Restart switch by using a cocktail stick or similar and the projector will restart.
3.
Some setting may be wrong. Please use the FACTORY RESET function of SERVICE menu in the OPTION menu
(37)
to reset all settings to factory
default. Then, if the problem is not removed after maintenance, please contact your dealer
or service company.
Phenomenon Cases not involving a machine defect
Reference
page
Power does not
come on.
The electrical power cord is not plugged in.
Correctly connect the power cord.
13
The power switch is not set to the on position.
Set the power switch to [ | ] (On).
16
The main power source has been interrupted during operation such as by a power outage (blackout), etc.
Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please turn the power on again.
16
Either there is no lamp and/or lamp cover, or either of these has not been properly fixed.
Please turn the power off, and allow the unit to cool down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.
38, 39
Page 47
47
ENGLISH
Phenomena that may easily be mistaken for machine defects (continued)
Phenomenon Cases not involving a machine defect
Reference
page
No pictures are
displayed.
The lens cover is closed.
Remove the lens cover.
4, 16
The signal cables are not correctly connected.
Correctly connect the connection cables.
10
The brightness is adjusted to an extremely low level.
Adjust the BRIGHT to a higher level using the menu function or the remote control.
23, 25
The computer cannot detect the projector as a plug and play monitor.
Make sure that the computer’s can detect a plug and play monitor using other plug and play monitor.
10
Colors have a
faded- out
appearance, or
Color tone is
poor.
Color settings are not correctly adjusted.
Perform picture adjustments by changing the COLOR TEMP,
COLOR, TINT and/or COLOR SPACE settings,
using the menu functions.
23, 25,
30
COLOR SPACE setting is not suitable.
Change the COLOR SPACE setting to AUTO, RGB, SMPTE240 , REC709 or REC601.
30
Pictures appear
dark.
The brightness and/or contrast are adjusted to an extremely low level.
Adjust the BRIGHT and/or CONTRAST settings to a higher level using the menu function.
24, 25
The WHISPER function is working.
Select the NORMAL to the item WHISPER in the SETUP menu.
24, 32
The lamp is approaching the end of its product lifetime.
Replace the lamp.
38, 39
Pictures appear
blurry.
Either the focus and/or horizontal phase settings are not properly.
Adjust the focus using the focus ring, and/or H PHASE using the menu function.
18, 28
The lens is dirty or misty.
Clean the lens by referring to the section “Caring for the lens”.
41
Troubleshooting
NOTE • Although bright spots or dark spots may appear on the screen, this
is a unique characteristic of liquid crystal displays, and such do not constitute or
imply a machine defect.
Page 48
48
Warranty And After-Service
Warranty and after-service
If a problem occurs with the equipment, first refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or the service company. They will tell you what warranty condition is applied.
Specifications
Specifications
NOTE • This specifications are subject to change without notice.
Item Specification
Product name Liquid crystal projector
Liquid Crystal panel
Panel size 1.8 cm (0.7 type) Drive system TFT active matrix
Pixels
CP-S335: 480,000 pixels (800 horizontal x 600 vertical)
CP-X340/X345: 786,432 pixels (1024 horizontal x 768 vertical) Lens Zoom lens F=1.7 ~ 1.9 f=21.8 ~ 26.2 mm Lamp 165W UHB Power Supply AC100-120V/2.7A, AC220-240V/1.5A Power Consumption 240W Temperature range
5 ~ 35°C (Operating)
Size
297 (W) x 64 (H) x 233 (D) mm
(Not including protruding parts)
• Please refer to the following figure.
Weight (mass)
2.5 kg
Ports
Optional parts
Lamp DT00671 Air filter
NJ09702
Others • Please consult your dealer.
RGB input:
RGB IN1 ..D-sub 15pin mini x1 RGB IN2 ..D-sub 15pin mini x1
RGB output:
RGB OUT D-sub 15pin mini x1
Communication port:
CONTROL ............D-sub 9pin x1
USB ....................... USB(B) x1
Video input:
COMPONENT VIDEO
Y ............................... RCA x1
CB/PB ....................... RCA x 1
CR/PR ...................... RCA x 1
S-Video ................................
1
Video ....................................
1
Audio input:
AUDIO IN1 ...... Stereo mini x1
AUDIO IN2 ...... Stereo mini x1
Audio output:
AUDIO OUT ...
Stereo mini x1
Page 49
49
ENGLISH
Specifications
Specifications (continued)
[unit: mm]
79.7
80.0
64.2
65.4
32.2
237.4
232.8
297.0
84.5
Page 50
Loading...