Hitachi CP-S220W User Manual

ENGLISH

Liquid Crystal Projector

CP-S220W

USER'S MANUAL

1-1

Thank you for purchasing this HITACHI liquid crystal projector.

Please read the accompanying manual “SAFETY INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference.

CONTENTS

FEATURES BEFORE USE

Contents of Package Part Names Loading the Battery

INSTALLATION

Installation of the projector and Screen Angle Adjustment Cabling Power Connection Example of System Setup Plug & Play

OPERATIONS

Power On/Off Basic Operation Menu Functions

MAINTENANCE

Cleaning Lamp

TROUBLESHOOTING

OSD Message Indicators Message Symptom Warranty and After-service

SPECIFICATIONS

Tables: Table 1-1. Installation Reference Table 1-2. Basic Operations Table 1-3. Menu Functions Table 1-4. OSD Message Table 1-5. Indicator Message Table 1-6. Symptom Table 1-7. Specifications Table 1-8. Example of Compatible Signal

NOTE:

* The information in this manual is subject to change without notice. * The manufacturer assumes no responsibility for any errors that may appear in this manual * The reproduction, transmission or use of this documents or contents is not permitted without

express written authority.

TRADEMARK ACKNOWLEDGMENT:

* PS/2, VGA and XGA are registered trademark of International Business Machines Corporation. * Apple, Macintosh, Mac and ADB are registered trademarks of Apple Computer, Inc. * VESA and SVGA are trademarks of the Video Electronics Standard Association. * Windows is registered trademarks of Microsoft Corporation. * Carefully observe the trademarks and registered trademarks of all companies, even when not

mentioned.

1-2

FEATURES

This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.

• Outstanding brightness

The UHB lamp and high-efficiency optical system assure a high level of brightness.

• Partial magnification function

Interesting parts of images can be magnified for closer viewing.

• Distortion correction function

Distortion-free images are quickly available.

BEFORE USE

Contents of package

Make sure all of the following items are included in the package. If anything is missing, please contact your dealer.

NOTE: Keep the original packing material for future reshipment.

Projector

User’s Manual

(this manual)

Safety Instructions

Power Cord

US Type

Power Cord

UK Type

Power Cord

Europe Type

RGB Cable Video Cable Audio Cable

(Stereo Mini)

Mac Adapter

VIDEO

STANDBY/ON

POSITION

FREEZE

MAGNIFY

VOLUME

AUTO

OFF

TIMER BLANK

SELECT

RGB

MUTE

MENU RESET

Remote Controller containing Battery

Carrying Bag

1-3

BBEEFFOORREE UUSSEE ((ccoonnttiinnuueedd))

ENGLISH

Part Names

Power Switch

AC Inlet

(to the Power Cord)

Ventilation Openings

(Intake)

ZOOM knob FOCUS ring

Remote Control Sensor

Lens Slide Lens door Foot Adjuster

FRONT/LEFT VIEW OF THE PROJECTOR

RESET Button

MUTE Button

INPUT Button

STANDBY/ON Button

Foot Adjuster Button

Air Filter and Intake

(for the Cooling Fan)

Speaker

Foot Adjuster

LAMP Indicator TEMP Indicator POWER Indicator MENU Button

Ventilation Openings (exhaust)

REAR/RIGHT VIEW OF THE PROJECTOR

Terminal Panel (Refer below)

S-VIDEO Terminal

RGB IN Terminal

CONTROL Terminal

VIDEO Terminal

Remote Control Sensor

AUDIO IN Terminal

TERMINAL PANEL

Control Panel (Refer to the section "OPERATIONS" for details)

1-4

BBEEFFOORREE UUSSEE ((ccoonnttiinnuueedd))

Part Names (continued)

VIDEO

STANDBY/ON

POSITION

FREEZE

MAGNIFY

VOLUME

AUTO

OFF

TIMER BLANK

SELECT

RGB

MUTE

MENU RESET

STANDBY/ON Button

Button

MENU Button

MAGNIFY Button

AUTO Button

TIMER Button

Battery Holder

OFF

VIDEO Button

RGB Button

MENU SELECT Button

POSITION Button

RESET Button

VOLUME Button

FREEZE Button

MUTE Button

BLANK Button

REMOTE CONTROLLER

Loading the Battery

First Loading:

In original packing, the battery is installed in the battery holder of the remote controller with protection film. Pull out the protection film to load the battery.

Replacing:

1. See the reverse side of the remote controller.

2. Pinch the groove and pull out battery holder as the drawing right.

3. Remove the worn battery.

4. Install the new battery with “+” side facing.

5. Push in and click the battery holder.

Pull out

“+” side

Battery Holder

(Refer to the section "OPERATIONS" for details)

CAUTION

Danger of explosion if battery is incorrectly replaced. Be careful in handling the battery according to instructions of the accompanying manual “SAFETY INSTRUCTIONS” and this manual. Replace only with the same or equivalent type recommended by the manufacturer. Use the 3V micro lithium battery Type no. CR2025 only. When you dispose the battery, you must obey the law in the relative area or country. Keep the battery away from children and pets.

1-5

INSTALLATION

Installation of the Projector and Screen

Install the projector in a suitable environment according to instructions of the accompanying manual “SAFETY INSTRUCTIONS” and this manual.

Refer to the drawing and table below for determining of the screen size and projection distance.

TOP VIEW

SIDE VIEW

a: Distance from the LCD projector to the screen.

The projection distance shown in the table below are for full size (800 x 600 dots).

b: Distance from the lens center to the bottom of the

screen (a, b: +/-10%)

Table 1-1. Installation Reference

Screen size

(inches)

a (inches)

b (inches)

Min. Max.

40 37 46 3

60 57 69 5

80 77 93 7

100 96 116 9

120 116 139 10

150 145 174 13

200 194 233 17

Angle Adjustment

Use the foot adjuster on the bottom of the projector to adjust the projection angle. It is variable within 0˚ to 10˚ approximately.

1. Lift up the front side of the projector.

2. Pressing the foot adjuster button, adjust the projection angle.

3. Release the button to lock at the angle to be fixed.

Do not release the foot adjuster button unless the projector is being held; otherwise, the projector could overturn or the fingers could get caught and cause personal injury.

10°

Foot Adjuster

ENGLISH

Press the foot adjuster button

Horizontal inclination may be adjusted using the adjuster at the rear.

Installation of liquid crystal projector

Please basically use liquid crystal projector at the horizontal position. If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and become the cause of damage. Be especially careful not to install it with ventilation holes blocked.

1-6

IINNSSTTAALLLLAATTIIOONN ((ccoonnttiinnuueedd))

RGB Signal Input:

Connect the RGB IN terminal of the projector to the display signal output of the computer by the enclosed RGB cable. Secure the screws on the connector and tighten. For some modes, the enclosed Mac adapter is necessary. Refer to the “Table 1-8. Example of Compatible Computer Signal” of the section “SPECIFICATION”. NOTE: Some computers may have multiple display screen modes. Use of some of these modes will

not be possible with this projector.

Video Signal Input:

Connect the VIDEO terminal of the projector to the video signal output of the video tape recorder by the enclosed video cable except for S-Video signal. For S-Video signal, use the S-VIDEO terminal of the projector and the optional cable for S-Video.

Audio Signal Input:

Connect the AUDIO IN terminal of the projector to the audio signal output by the enclosed audio cable.

RS232C:

Connect the CONTROL terminal of the projector to the computer.

Power Connection:

Use the correct one of the enclosed power cords depending on the power outlet to be use. Connect the AC inlet of the projector to the power outlet firmly by the power cord

Cabling

Before connecting, read the instruction manuals of the devices to be connected, and make sure that the projector is compatible with the device, and turn off to all devices to be connected.

WARINING

Be carful in handling the power cord according to instructions of the accompanying manual "SAFETY INSTRUCTIONS" and this manual. Connect the power cord firmly. Avoid using a loose, unsound outlet or contact failure.

AC INLET

Power Cord

Power outlet

1-7

IINNSSTTAALLLLAATTIIOONN ((ccoonnttiinnuueedd))

ENGLISH

Example of system setup

AC Input

Video tape recorder with S jack

Video tape recorder

Computer

(desktop type)

Computer

(notebook type)

Plug & Play

This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer that is VESA DDC (Display Data Channel) compatible. (Plug & play is a system configured with peripheral equipment including a computer and display, and an operating system. NOTE: Use the RGB cable included with this projector when using plug & play. With other cables,

pins (12) - (15) are sometimes not connected (effective only for RGB).

1-8

OPERATIONS

Power On/Off

Power On

1. Confirm that power cord is connected properly.

2. Push "I" of the power switch. Standby mode is set up and power source indicator burns in the orange.

3. Push a control panel or "STANDBY/ON" of the remote controller. A warm-up is started and power source indicator goes on and off in green.

4. When power source on is completed, power source indicator finishes blinking, and burns in green. Open a Slide lens door.

5. Adjust picture size using the projection lens ZOOM knob.

6. Adjust focus using the projection lens FOCUS ring.

Power Off

1.Push a control panel or "STANDBY/ ON" of the remote controller for about one second. The

ramp of projector disappears and cooling of the ramp is started. Power source indicator goes on and off in the orange during ramp cooling. It is ineffective even if power source indicator pushes "STANDBY/ ON" button during the blinking.

2. When ramp cooling is completed, STANDBY mode is set up and power source indicator stops blinking, and burns in the orange. Confirm this, and push the "O"side of the power switch. Don't make power switch OFF when power source indicator burns in the orange except for the emergency. The time when power source indicator is green and power source OFF during the blinking shorten the life of projector lamp.

3. Power source indicator disappears when power source OFF is completed. Close without forgetting a lens door.

Power Switch

Slide Lens door

STANDBY/ON Button

POWER Indicator

VIDEO

STANDBY/ON

POSITION

FREEZE

MAGNIFY

VOLUME

SELECT

RGB

MENU RESET

STANDBY/

ON Button

ZOOM knob

FOCUS ring

Read the "SAFETY INSTRUCTIONS" of this calligraphy and the separate volume well surely and use it for the safety before the use after attention.

Make the power source of the computer ON before projector when using a RS-232 communications function.

+ 18 hidden pages