Hitachi CML150XU, CML150XE User Manual

HITACHI

USER MANUAL

Liquid Crystal Colour Monitor

CMLI

50XE

BEDIENUNGSANLEITUNG
MANUAL

MANUAL DE USUARIO

UTILISATEUR

CMLI50XU

with

EasyMenu !

EasyMenu is HITACHI’s On Screen Display function for easy operation.

READ THE INSTRUCTIONS INSIDE CAREFULLY.

KEEP THIS USER MANUAL FOR FUTURE REFERENCE.

For future reference, record the serial number of your colour monitor.

,

MANUALE D’USO

SERIAL No.

The serial number is located on the rear of the monitor.

This monitor is
equipped with VESA DPMS.

The

ENERGY STAR@

any product or service.
As an

ENERGY STAR@

product meets the

ENERGY STAR@

emblem does not represent EPA endorsement of

Partner, Hitachi,Ltd. has determined that this

ENERGY STAR@

compliant when used with a computer

guidelines for energy efficiency.

NOTE:

The information in this manual is subject to change without notice.
responsibility for any errors that may appear in this manual.

TRADEMARK ACKNOWLEDGEMENT

VGA

is a registered trademark of International Business Machines Corporation.

APPLE

is a registered trademark of Apple Computer, Inc.

VESA is a trademark of a nonprofit organization, Video Electronics Standard Association.

ENERGY STAR@

is a US. registered mark of Environmental Protection Agency (EPA).

The manufacturer assumes no

HINWEIS:

Anderungen der Daten in dieser Bedienungsanleitung sind vorbehalten.

keine Haftung fur jegliche in diesem Handbuch eventuell enthaltenen

GESCHiiTZTE WARENZEICHEN

VGA ist ein eingetragenes Warenzeichen der International Business Machines Corporation.
APPLE ist ein eingetragenes Warenzeichen der Apple Computer, Inc.
VESA ist ein Warenzeichen der Video Electronics Standard Association, einer Organisation ohne

Erwerbscharakter.

ENERGY STAR@

ist ein Warenzeichen der Environmental Protection Agency (EPA).

Der Hersteller ubernimmt

IrrtOmer.

REMARQUE:

Les informations contenues dans ce manuel peuvent btre modifiees sans preavis.
n’accepte aucune responsabilite pour les erreurs qui peuvent eventuellement apparaitre dans ce
manuel.

MARQUES

VGA est une marque deposee d’ International Business Machines Corporation.
APPLE est une marque deposee d’Apple Computer, Inc.
VESA est la marque

ENERGY STAR@

DEPOSCES

dune

est une marque de I’ EPA (Environmental Protection Agency, USA).

organisation sans but lucratif, la Video Electronics Standard Association.

Le constructeur

NOTA:

La information contenida en este manual esth sujeta a cambios sin previo aviso.
se responsabiliza de

RECONOCIMIENTO DE

VGA es una marca registrada de International Business Machines Corporation.

APPLE es una marca registrada de Apple Computer, Inc.

VESA es una marca registrada de una

Association.

ENERGY STAR@

10s

errores que puedan aparecer en este manual.

MARCAS

organization

es una marca de Environmental Protection Agency (EPA).

sin animo de

lucre,

Video Electronics Standard

El fabricante no

NOTA:

Tutte le informazioni di quest0 manuale sono soggette ad essere modificate senza preavviso. II
costruttore non si assume responsabilita’ per errori

Marchi

di fabbrica riconosciuti.

VGA e’

urn

APPLE e’

VESA e’ il marchio di riconoscimento della organizzazione a non-profitto, Video Electronics
Standard Association.

ENERGY STAR*

marchio di fabbrica regisrato da International Business Machine Corporation.

urn

marchio di fabbrica regisrato da Apple Computer, Inc.

e’ il marchio di fabbrica della Eviromental Protection Agency (EPA).

the

possono essere riportati

sul

manuale.

n TC0’95 STATEMENT

Congratulations!

You have just purchased a TCO’95 approved and labelled product!
Your choice has provided you with a product developed for

professional use. Your purchase has also contributed to reducing the
burden on the environment and also, to the further development of

environmentally adapted electronics products.

Why do we have environmentally

In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment. The main problem, as far as computers and
other electronics equipment are concerned, is that environmentally harmful substances are used
both in the products and during the manufacturing. Since it has not been possible for the majority of
electronics equipment to be recycled in a satisfactory way, most of these potentially damaging
substances sooner or later enter Nature.

There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (internal) and natural (external) environments. Since
all methods of conventional electricity generation have a negative effect on the environment (acidic
and climate-influencing emissions, radioactive waste, etc.), it is vital to conserve energy. Electronics
equipment in offices consume an enormous amount of energy since they are often left running
continuously.

What does labelling involve?

This product meets the requirements for the
environmental labelling of personal computers. The labelling scheme was developed as a joint effort
by the TCO (The Swedish Confederation of Professional Employees), Naturskyddsforeningen (The
Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and
Technical Development in Sweden).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of
electrical and magnetic fields, energy consumption and electrical and fire safety.

The environmental demands concern restrictions on the presence and use of heavy metals,
brominated and chlorinated flame retardants,
things. The product must be prepared for recycling and the manufacturer is obliged to have an
environmental plan which must be adhered to in each country where the company implements its
operational policy.

The energy requirements include a demand that the computer and/or display, after a certain
period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The
length of time to reactivate the computer shall be reasonable for the user.

Labelled products must meet strict environmental demands, for example, in respect of the reduction

of electric and magnetic fields, physical and visual ergonomics and good usability.
On the back page of this folder, you will find a brief summary of the environmental requirements met
by this product. The complete environmental criteria document may be ordered from:

TCO Development Unit

S-l 14 94 Stockholm
Sweden

Fax:

+46

Email (Internet): [e-mail]

Current information regarding TC0’95 approved and labelled products may also be obtained via

the Internet, using the address:

http://www.tco-info.com/

TC0’95 is a co-operative project between TCO (The Swedish Confederation of Professional

Employees), Naturskyddsforeningen (The Swedish Society for Nature Conservation) and NUTEK

(The National Board for Industrial and Technical Development in Sweden).

8 782 92 07

labelled

TCO’95

CFCs

computers?

scheme which provides for international and

(freons) and chlorinated solvents, among other

Environmental Requirements

Brominated flame retardants

Brominated flame retardants are present in printed circuit boards, cables, wires, casings and
housings. In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer
casing can consist of flame retardant substances. These are related to another group of
environmental toxins,
damage in fisheating birds and mammals, due to the bio-accumulative” processes. Flame
retardants have been found in human blood and researchers fear that disturbances in foetus
development may occur.

TCO’95

contain organically bound chlorine and bromine.

Lead2)

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the
nervous system and in higher doses, causes lead poisoning.

Cadmium2’

Cadmium is present in rechargeable batteries and in the colourgenerating layers of certain computer

displays. Cadmium damages the nervous system and is toxic in high doses.

cadmium. The colour-generating layers of display screens must not contain any cadmium.

Mercury”

Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous
system and is toxic in high doses.

of mercury. It also demands that no mercury is present in any of the electrical or electronics
components concerned with the display unit.

demand requires that plastic components weighing more than 25 grams must not

TCO’95

requirement permits the inclusion of lead since no replacement has yet been developed.

TCO’95

requirement states that batteries may not contain more than 25 ppm (parts per million) of

TCO’95

requirement states that batteries may not contain more than 25 ppm (parts per million)

PCBs,

which are suspected to give rise to similar harm, including reproductive

CFCs

(freons)

CFCs

(freons) are sometimes used for washing printed circuit boards and in the manufacturing of

expanded foam for packaging.

thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of

ultraviolet light with consequent increased risks of skin cancer (malignant melanoma).

The relevant

manufacturing of the product or its packaging.

‘)

Bio-accumulative is defined as substances which accumulate within living organisms

*’

Lead, Cadmium and Mercury are heavy

3,

This

monitor

backlight system. Total amount of mercury in this monitor is less than

TC0’95

contains LCD module

CFCs

break down ozone and

requirement: Neither

metals

which are Bio-accumulative.

(FLQBXGCGV).

CFCs

nor

HCFCs

LCD module uses

may be used during the

the

4 lamp tubes for the

IP.Omg.

FEATURES..
CAUTIONS

INSTALLATION..26..................................................................................................

STANDARD SETTINGS ......................................................................................

OPERATION ......................................................................................................

AUTOMATIC SIGNAL CHECK.......................................................................... 13

POWER SAVING SYSTEM ............................................................................... 13

PLUG & PLAY

SPECIFICATIONS.. ...........................................................................................

The following features are provided by the Liquid Crystal Colour Monitor.

........................................................................................................

...........................................................................................................

....................................................................................................

10

13
14

Wide-range Multi scanning

This product is a high resolution monitor capable of resolutions up to 1024 X 768 dots.
Automatic scanning and automatic adjustment to conform with a wide-range of scanning
frequencies and user requirement.

High performance LCD achieves the best quality

The wide viewing angle (more than

High contrast (typical

300:1),

160°

at horizontal and vertical axis).

High brightness (typical

250cd/m2)

and anti-glare.

Digital Picture Control Function

Clock, Phase, Position and Colour are adjustable by operations from the front switches.

Geometry setting can be stored for different HN frequencies.

preset functions can store 27 sets of geometry settings including the standard factory

settings. And an adjusted colour setting can be stored and recalled by the Colour

Select function.

Microprocessor-based

EasyMenu

An On Screen Display function that allows direct access to adjust all operations from the

front switches.

Power Saving System

The Environmental Protection Agency (EPA) has established a voluntary program by

which manufacturers enable computer products to go into low power states while not

being used. This monitor has a low power

requirements for the ENERGY

Please refer to the section of “POWER SAVING SYSTEM” for details.

STARS

PLUG & PLAY

This monitor is VESA

used with a computer compliant with VESA

DDC (Display Data Channel)

DDCIRB

compliant when

“off’

mode, which is compliant with the EPA

program, and will assist you in conserving energy.

“St

a+--

1

7
9

ENGLISH -

1

w

IF ANY ABNORMALITY OCCURS, immediately TURN OFF and DISCONNECT

-s

THE POWER PLUG from the power point ! Then check that there is no

-

smoke and no fire, and contact your dealer.

.I

An abnormality (abnormal smell, smoke, abnormal or no picture, abnormal sound,

damaged, shocked, insert foreign object, etc.) could cause a fire, electric shock, etc.

DO NOT apply any shock to the monitor.
DO NOT insert any foreign object into the monitor.
DO NOT oil the monitor.

The power point should be close to the monitor and easily accessible.

w

NEVER REMOVE THE CABINET !

The monitor contains high voltage components.

inside, if you want.

n

BE CAREFUL IN HANDLING THE LCD (Liquid Crystal Display) !

DO NOT touch the liquid crystal even if the monitor is damaged, to prevent a injury to
health.

the mouth, eyes, etc., consult a doctor.

For dumping, you MUST comply with the rule of the area in which you are dumping it.
DO NOT scratch, press or strike the LCD screen.
DO NOT adhere a drop of water etc. to the LCD screen. When a drop is found on the
screen, wipe lightly with a soft cloth, at once.

n

to prevent a fire, electrical shock, etc.
DO NOT expose the monitor to rain, moisture, dust, corrosive gases, vibrations, etc.
AVOID placing the monitor in direct sunshine or near a heating appliance.
DO NOT place on an unstable place.

When you touched it, wash your hands clean.

INSTALL THE MONITOR IN AN SUITABLE ENVIRONMENT !

Ask your dealer to repair or clean

If the liquid crystal adhered to

n

KEEP IN A WELL VENTILATED PLACE !

DO NOT cover this monitor or place anything against any sides (not only the top, right
and left side but also the rear and bottom side) of monitor. Ventilation holes are
provided at all sides of cabinet to prevent the temperature from rising.

n

TAKE CARE OF THE AMBIENT ILLUMINATION

Avoid direct rays of the sun or room lighting onto the screen in order to prevent eye
fatigue.

ENGLISH - 2

n

THE ENCLOSED POWER CORD MUST BE USED !

Failure to do so may cause electric shock hazard or fire hazard.

In USA/Canada, use a UL LISTEDKSA

meeting the following specifications :

Rating: min.

Plug type: NEMA

In Europe, a proper European standard approved power cord is to be used with this

monitor.

H05WH2-F 3G 0.75

H

USE ONLY THE CORRECT VOLTAGE POWER OUTLET WITH SAFETY

125V,

7A , Length: max.

5-15P

figure, Parallel blade, Grounding type

For a rated current up to 6 A, a type not lighter than

mm2

must be used

LABELLED

3.0m

, Type: SVT or SJT

or CERTIFIED power cord set

H05W-F

3G 0.75

mm*

or

GROUND CONNECTION !

100 - 120 V for USA, Canada, etc.
200 - 240 V for Europe, etc.
(This monitor will automatically adjust to the input voltage 100 - 120 / 200 - 240V.)

II

CAUTION for 200 - 240V operation only

This equipment relies on the protective devices in the building installation for short-circuit

and over-current protection. Refer to the following table for the suitable number and

location of the protective devices which should be provided in the building installation.

INFORMATIVE EXAMPLES OF PROTECTIVE DEVICES IN SINGLE - PHASE

EQUIPMENT OR SUB -ASSEMBLIES

.

E

neutral reliably

Verify that the protective devices in the building installation meets the conditions in the
table prior to installing the equipment.

identified,

except for

Either of the two

Either of the two

ENGLISH - 3

n

BE CAREFUL OF POWER CORD CONNECTION !

Before inserting the plug of the power cord into a receptacle of the correct voltage, check

that the connection portion of the power cord is clean (with no dust).

plug of power cord to a receptacle firmly, otherwise it may cause electric shock or fire

=

hazard.

n

y

.I

REMOVE THE POWER CORD FOR COMPLETE SEPARATION !

For complete separation from the power source, remove the power cord from the monitor

or from the wall outlet.

Then, insert the

H ABOUT CLEANING

Wrong cleaning may cause a damage to the monitor.

Cleaning the monitor in following way :
Before cleaning, turn off the power switch and disconnect the plug from the power point.
For the cabinet, use water or a diluted soapless soap with water, with soft cloth like

gauze.
For the LCD screen, use isopropyl alcohol with soft cloth like qauze, lightly.
DO NOT clean the inside of monitor yourself as it is very dangerous.
DO NOT use aerosol sprays, solvents or abrasive cleaners.

Ask your dealer.

ENGLISH - 4

w FCC (Federal Communications Commission) STATEMENT WARNING

WARNING : This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures :

.

Reorient or relocate the receiving antenna.

.

Increase the separation between the equipment and receiver.

.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

.

Consult the dealer or an experienced radio I TV technician for help.

INSTRUCTIONS TO USERS

Communication Commission) equipments provided that following conditions are met.
(1) Power cord : Unshielded power cord must be used.
(2) Video inputs : The input signal amplitude must not exceed the specified level.

CAUTION : Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

We:

Located at:

Declare under sole
15 of the FCC rules as a Class B digital
representative unit tested and found to be compliant with the standards.

continue to reflect the equipment being
due to quantity production and testing on a statistical basis as required by 47CFR 52.909.
Operation is subject to the following
interference, and
may cause undesired operation. The above named party is responsible for ensuring that the
equipment complies with the standards of 47CFR I f 15.‘lOl to 15.109.

Trade name:

Model Number:

Niisei Sangyo

200 Lowder Brook Drive Snite 2200, Westwood, MA.

res.ponsibiUty

(2)

This device must accept any interference received, including interference that

Liquid Crystal Display Monitor

CMLlSOX I CMLISDXA /

:

This equipment complies with the requirements of FCC (Federal

Declaration of Conformity

According io

Class B Personal Computers and

CPIJ

Boards and Power Supplies used

with

Class B Personal Computersi

47CFR.

Part

2 and 15 for

Peripherals; and I or

America, Ltd.

02090-1124

that the product identifBd herein, complies with 47CFR Part 2 and

device.

pmduced

two condiions:

Each

produci

marketed, is identical to the

can be expected to be within the variation accepted,

(1) This device may not cause harmful

CMLlSOXTE I CMLXSOXTA

U.S.A.

Records maintained

’

E
E

-

Signature of Patty Responsibie:

Satoshi

Printed name of Party Responsible:
Executed on (Date), at (Place):

n

FOR THE CUSTOMERS IN CANADA

Tanabe

June 18.1998, MA., U.S.A.

NOTICE : This Class B digital apparatus complies with ICES-003.

ENGLISH - 5

n FOR THE CUSTOMERS IN THE U.K.

THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND

EUROPE.

-i

-

-

.I

The mains lead on this equipment

of which is indicated on the pin face of the plug.

BSI approved BS 1362 fuse must be used of the same rating.

never use the plug with the cover omitted.
the same colour as that visible on the pin face of the plug.
dealer.

DO NOT cut off the mains plug from this equipment.
points in your home or the cable is too short to reach a power point, then obtain an appropriate
safety approved extension lead or consult your dealer.

Should it be necessary to change the mains plugs, this must be carried out by a competent person,
preferably a qualified electrician.

If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately,
having first removed the fuse, to avoid a possible shock hazard by inadvertent connection to the
mains supply.

IMPORTANT
The wires in the mains lead are coloured in accordance with the following code :

As these colours may not correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug

FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE.

IMPORTANT FOR UNITED KINGDOM

WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS

is supplied with a moulded plug incorporating a fuse, the value

Should the fuse need to be replaced, an ASTA or

If the fuse cover is detachable

If a replacement fuse cover is required, ensure it is of

Fuse covers are available from your

If the plug fitted is not suitable for the power

WARNING: THIS EQUIPMENT MUST BE EARTHED

Green and Yellow = Earth, Blue = Neutral, Brown = Live.

Green & Yellow
to Earth

Blue to Neutral

which is marked with the letter E or by the earth symbol 0 or coloured GREEN or GREEN and
YELLOW.

The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured

BLUE or BLACK.

letter L or coloured BROWN or RED.

ENGLISH -

The wire coloured BROWN must be connected to the terminal marked with the

6

Brown to Live

Fuse

Cord Clamp

LCD Screen

Cabinet

\

Control
Switches.

Tilt Base

Power

Switch

Opening

\

for Cables

FRONT VIEW

REAR VIEW

Install the monitor in the following way, taking care to maintain safety :

Install the monitor on a horizontal base.
Remove the “Tilt Base Cover” and the “Terminal Cover”.

First, catch the centre of upper edge of the “Tilt Base
Cover”, and tip down on this side to detach it.

Then, seize the centre of bottom edge of the “Terminal
Cover”, and turn it behind to detach it.

Use video signal cable which is included in the carton
box. (Cable model name:HD-0501 FXL)

For computer use , insert the connector of a signal cable
to the “ANALOG” terminal of the monitor, with attention
to the suitability, and secure the screws on the
“ANALOG” terminal shell firmly. And draw the cable
around by guides.

.ANALOG

Terminal

Cover

Tilt Base

Cover

tPin No.1

1

2

3

Sianal

Red Video

-

Green Video (Sync. optional)

Blue Video

ENGLISH - 7

@

Make sure of using the power cord meeting the safety standard of the country in

which you are using the monitor, and insert the connector of a power cord to the “AC

Inlet” of the monitor.

-

@I

-=a

-

Set the “Terminal Cover” first, then “Tilt Base Cover”. Let the signal cable and

­_

-

power cord pass through the “Opening for Cables”.

0

Connect the another connector of the signal cable to the computer.

@I

Insert the plug of the power cord to a power outlet of the correct voltage.

@

Turn on “Power Switch” of the monitor first, then the computer.

“POWER ON/OFF”.

If the graphics board supplies more than one type of sync. signal, the sync.

NOTE :
signal type will be automatically selected by the monitor, with the priority shown in the
following table.

Refer to page 10

Sync. Signal Type

H,V Separate Sync.

HIV Composite Sync.
Sync. on Green Video

Priority

1

2
3

ENGLISH - 8

Microprocessor-based preset functions can store 27 sets of geometry settings including

the standard settings. The following industrial standard settings have been pre-

programmed by the factory.

NOTE :

.

Input signals with approximately the same frequencies may be regarded as the same

signal.

.

Standard settings are subject to change without notice.

1

E
tl

-

ENGLISH - 9

Adjust Switch

Auto Switch

POWER ON/OFF

_

Power Switch

To turn ON , press the “ j ‘I side of the Power Switch.
To turn OFF , press the

:

NOTE

*

When power is ON, the Power Indicator lights.

“0”

side of the Power Switch.

RIGHT SIDE VIEW

AUTO ADJUST

To adjust phase, clock, H-position, V-position Automatically, press the Auto Switch

:

NOTE

*

The other functions do not operate while automatic adjustment is in progress.

.

Proceed to automatic adjustment after more than 20 minutes have passed since the

power is ON.

*

Select the bright image for display while automatic adjustment takes place.

.

If automatic adjustment terminates unsuccessfully, try automatic adjustment again. If

automatic adjustment fails several times in succession, try using manual adjustment.

Refer to page 11 “CONTROL” .

-

The display may become unclear or distorted while automatic adjustment is in

progress.

-

The Auto Switch is invalid while the On Screen Display function of “EasyMenu” is

shown.

ENGLISH - 10

CONTROL

@

Press the Menu Switch. the EasyMenu shows the selected function, its condition, the

function menu and the input signal resolution and vertical frequency.

@

To select the function, use the Select Switches.

@I

To execute the selected function, use the Adjust Switches. Refer to “TABLE:Control

for COMPUTER USE” below.

NOTE :

.

You can select the EasyMenu language. Use the function “LANGUAGE SELECT”.

*

To clear the EasyMenu, either push the Menu Switch again or wait for 10 seconds.

*

You can save the your geometry and color settings Automatically at clearing the

EasyMenu.

.

Adjustment may not be perfect depending on the computer or video board you are

using.

-

g$igggg~17~-=-

SAMPLE OF

TABLE : Control for COMPUTER USE

;a

BRIGHTNESS makes Brightness darker.

0

CONTRAST makes the Contrast intensity makes the Contrast intensity

lmJ CLOCK

@

PHASE adjusts the phase to correct blurred or unstable images.

“EasyMenu”

Function

for COMPUTER USE

-

weaker.

adjusts the dot clock frequency to reduce

the vertical stripe.

+

makes Brightness brighter.

stronger.

E

,’

V.POSITION moves the position

down.

y.

EXPANSION

enables (ON)

the expanding function.

COLOR SELECT

2.

changes the colour to the changes the colour to the
previous mode.

USER - 3 - 2 + 1

moves the position

UD.

disables (OFF)
the expanding function.

next mode.

1

---)

2 --, 3 + USER

ENGLISH -

I

II

TABLE CONTINUED

Function

-

+

R

&A

COLOR

BALANCE

m

ENHANCE enables (ON) the enhancing disables (OFF) the enhancing

makes the Red weaker.

G makes the Green weaker.

B

makes the Blue weaker. makes the Blue stronger.

function.

LANGUAGE SELECT changes the EasyMenu changes

m

language to the previous language to the next mode.
mode.

FRANCAIS

(French)

1

ITALIAN0 (Italian)

1

ESPANOL (Spanish)

1

DEUTSCH (German)

1

makes the Red stronger.
makes the Green stronger.

function.

the

EasyMenu

ENGLISH

1

DEUTSCH (German)

1

ESPANOL (Spanish)

1

ITALIAN0 (Italian)

1

FRANCAIS (French)

ENGLISH

iAUTDl

AUTO

ADJUST

adjusts input signal level in addition to phase, clock,

H-

position, and V-position automatically .

El

RECALL

recalls the factory preset modes.
(Refer to page 9 “STANDARD SETTINGS”.)

‘I)

.

Proceed to automatic adjustment after more than 20 minutes have passed since the

power is ON.

*

Proceed to automatic adjustment when the adjustment pattern included in the

attached “Utility Disk” is shown.

.

To show the adjustment pattern, follow

*

If automatic adjustment terminates unsuccessfully, try automatic adjustment again. If

“readmetxt”

in the attached “Utility Disk”.

automatic adjustment fails several times in succession, try using manual adjustment.
Refer to page 11 “CONTROL”

. The display may become unclear or distorted while automatic adjustment is in

progress.

.

The other functions do not operate while automatic adjustment is in progress.

ENGLISH - 12

When the monitor has detected the change of the signal input condition, the monitor will

indicate the condition, as follows.

Indication

Sample of EasyMenu

Condition

,

c

This monitor complies with VESA DPMS and

ENERGY

STAR@

Power saving requirements.
The power saving system works only when used with VESA DPMS compliant PC’s
and/or graphic controllers.

Power Saving States

45W max.

Power Indicator

Lighting Green

On

Mode

VESA DPMS

Video

H.Sync. V.Sync.

Active Yes Yes

Power Consumption

Standby Blanked No Yes
Suspend
Off

Blanked

Yes

Blanked No

No
No

This monitor complies with VESA DDC

1/2B

5W max.

specifications.

with computer, peripherals (including monitors), and operating system.

Lighting Orange

Plug & Play is a system

It works when
the monitor is connected to DDC ready computer that is running an operating system
software that is capable for the plug & play.

ENGLISH - 13

LCD

-

-

-

-

-

mm

Input Signal

Co/ours

Synchronization

Resolution

Viewable
Viewable

image Size
Image Area

Co/our Temperature

Warm-up Time

Power Supply

15 inch Liquid Crystal Display panel
Pixel pitch 0.297 mm,
Contrast

Viewing angle horizontal 160 X vertical 160 degrees
Sync.

Video : 0.7 Vp-p, analog

16.19 million
Horizontal : 31 - 60

Vertical : 56 - 75 Hz
Horizontal : 1024 dots (max.)

Vertical : 768 lines (max.)

15.0 inches (380 mm), diagonal
Horizontal : 304 mm (typical)

Vertical

USER
20 minutes to reach optimum performance level.

AC 100 - 120 I 200 - 240 V

50/60

(automatically selected)

Power Consumption : 45 W (max.)

(provided with power save circuit.)

3OO:l

(typical), Brightness

: Separate

Composite H/V, TTL level
Sync. on Green at 0.30 Vp-p

: 228 mm (typical)

1

2

3

: Standard colour balance, 9300K
: Standard colour balance, 6500K
: LCD original colour (not adjusted)
: User defined

Hz

HA/,

kHz

TTL level

(0.9A I 0.55A)

250cd/mz

(typical)

(typical),

408

o/v) X

Dimensions

Weight

5.5 kg (approx.)

Environmental

Condition

Specification and Design are subject to change without notice.

NOTE :

ENGLISH - 14

Temperature
Humidity

372 (H) X 215 (D) mm

Operation
5°C to

35OC

30% to 85%

-

Storage

1 OT to

5% to 85%

5o”c

Hitachi, Ltd. Tokyo, Japan

International Sales Division

THE HITACHI ATAGO BUILDING,

No. 15 –12 Nishi Shinbashi, 2 – Chome,

Minato – Ku, Tokyo 105-8430, Japan.

Tel: [phone]

HITACHI EUROPE LTD. HITACHI EUROPE S.A.

Dukes Meadow 364, Kifissias Ave. & 1, Delfon Str.

Millboard Road 152 33 Chalandri

Bourne End Athens

Buckinghamshire GREECE

SL8 5XF Tel: [phone]

UNITED KINGDOM Fax: [phone]

Tel: [phone] Email: [e-mail]

Fax: [phone]

Email: [e-mail]

HITACHI EUROPE GmbH HITACHI EUROPE S.A.

Munich Office Gran Via Carlos III, 101 - 1

Dornacher Strasse 3 08028 Barcelona

D-85622 Feldkirchen bei München SPAIN

GERMANY Tel: [phone]

Tel: [phone] Fax: [phone]

Fax: +49 - 89 - 991 80 -224 Email: [e-mail]

Hotline: +49 - 180 - 551 25 51 (12ct/min.)

Email: [e-mail]

HITACHI EUROPE AB

HITACHI EUROPE SRL Box 77

Via T. Gulli n.39 S-164 94 KISTA

20147 MILAN SWEDEN

ITALY

Tel: [phone] Fax: [phone]

Fax: [phone]

Servizio Clienti

Tel. [phone]

Email: [e-mail]

HITACHI EUROPE LTD.

HITACHI EUROPE S.A.S Norwegian Branch Office

Lyon Office Strandveien 18

B.P. 45, 69671 Bron Cedex 1366 Dysaker

FRANCE NORWAY

Tel: [phone] Tel: [phone]

Fax: [phone] Fax: [phone]

Email: [e-mail] Email [e-mail]

ITEM N.V./S.A. (INTERNATIONAL TRADE FOR

ELECTRONIC MATERIAL & MEDIA N.V./S.A)

UCO Tower – Bellevue, 17

B – 9050 GENT

BELGIUM (for BENELUX)

Tel: [phone]
Fax: [phone]

Email:

www.hitachi-consumer-eu.com

[e-mail]

Tel: [phone]

Email: [e-mail]