Hitachi C14-RF60 Service Manual
C14-RF60
SERVICE MANUAL
PAL/SECAM/NTSC
YS
No.
C14-RF60
Destination Code
HONG KONG 051
JAP AN T OURIST 981J
GA1 Chassis
CAUTION: Before servicing this chassis, it is important that the service technician read the
"IMPORTANT SERVICE NOTES" in this Service Manual.
CONTENTS
Page
» SPECIFICATIONS ..............................................2
» IMPORTANT SERVICE NOTES .........................2
» ADJUSTMENT PRECAUTIONS.........................3
» MEMORY MAP .................................................11
» GA1 HOTEL MODE APPLICATION................. 15
» TROUBLE SHOOTING T ABLE .........................16
» CHASSIS LAYOUT ...........................................18
» BLOCK DIAGRAM ............................................19
» DESCRIPTION OF SCHEMATIC DIAGRAM....23
» SCHEMATIC DIAGRAMS
Ë MAIN UNIT ................................................... 24
Ë CRT UNIT......................................................26
Ë HEADPHONE UNIT ......................................26
Ë MULTI UNIT ..................................................27
» PRINTED WIRING BOARD ASSEMBLY ..........28
» SOLID STATE DEVICE BASE DIAGRAM........ 34
» REPLACEMENT PARTS LIST ......................... 35
Ë ELECTRICAL PARTS
MAIN UNIT................................................... 36
CRT UNIT......................................................40
HEADPHONE UNIT ......................................40
MULTI UNIT ..................................................41
Ë SUPPLIED ACCESSORIES......................... 42
Ë PACKING PARTS ..........................................42
Ë CABINET PARTS ..........................................42
» PACKING OF THE SET ....................................43
Page
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
COLOUR TELEVISION
JULY 2003 Digital Media System Group, Hitachi Asia Ltd.
C14-RF60
2-2
qualified service personnel only.
IMPORTANT SERVICE NOTES
Maintenance and repair of this receiver should be done by
SERVICING OF HIGH VOLTAGE SYSTEM AND
PICTURE TUBE
When servicing the high voltage system, remove static charge from it by
Connecting a 10K ohm Resistor in series with an insulated wire(such as a
test probe) between picture tube dag and 2nd anode lead. (AC line cord
should be disconnected from AC outlet.)
1. Picture tube in this receiver employs integral implosion protection.
2. Replace with tube of the same type number for continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing shatterproof goggles and after
discharging the high voltage completely.
X-RAY
This receiver is designed so that any X-Ray radiation is kept to an absolute
minimum. Since certain malfunctions or servicing may produce potentiall y
than 23.7kV(at beam 0 µA) for the set.
1. When repairing the circuit, be sure not to increase the high voltage to more
hazardous radiation with prolonged exposure at close range, the following
2. To keep the set in a normal opeartion , be sure to make it function on
precautions should be observed:
NTSC-M
SECAM-B/G/DK/K1
repairing, never forget to check for such high voltage after the work.
* If there is a possibility that the high voltage fluctuates as a result of the
22.5kV±1.5kV(at beam 800 µA) in the case of the set. The set has been factory -
Adjusted to the above-mentioned high voltage.
C1(49.75MHz) thru C12(216.25 MHz)
may cause excess X-ray radiation.
3. Do not substitute a picture tube with unauthorized types and/or brands which
J1(91.25MHz) thru J12(217.25MHz)
S1(105.25MHz) thru S36(423.25MHz)
BEFORE RETURNING THE RECEIVER
Before returning the receiver to the user, perform the follo wing safety Checks.
J13(471.25MHz) thru J62(765.25MHz)
S37(431.25MHz) thru S41(463.25MHz)
C13(471.25MHz) thru C57(863.25MHz)
US2(55.25MHz) thru US13(211.25MHz)
US14(471.25MHz) thru US69(801.25MHz)
1. Inspect all lead dress to make certain that leads are not pinched or that
hardware is not lodged between the chassis and other metal parts in the
fishpapers, cabinet bac ks, adjustment and compartment co vers or shields, iso-
lation resistor- capacity networks, mechanical insulator s etc.
receiver.
2. Inspect all protective devices such as non-metallic control knobs, insulating
Depth:365.0mm
Height:333.0mm
Weight(approx):9.5kg
2-1
SPECIFICATIONS
Convergence .............................................................................. Self Convergence System
Focus ....................................................................................Quadra-Potential Electrostatic
Picture IF Carrier ................................................................................................38.9MHz
Sweep Deflection................................................................................................... Magnetic
Intermediate Frequencies
6.5MHz .............................................................................................................32.4MHz
6.0MHz .............................................................................................................32.9MHz
5.5MHz .............................................................................................................33.4MHz
Sound IF Carrier Frequency
4.5MHz .............................................................................................................34.4MHz
Colour Sub-Carrier Frequency .............................................................................34.47MHz
Power Input...................................................................................110 ~ 240V AC 50/60 Hz
Power Consumption ......................................................................................................62W
Audio Power Output Rating ........................................................................... 2.5W × 2(rms)
Size .............................................................................................. 5 × 9 cm Elliptic (2 pcs)
Speaker
VHF/UHF ......................................................................................75 ohms Unbalanced
Voice Coil Impedance ........................................................................ 16 ohms at 400 Hz
Aerial Input Impedance
Receiving System........................................................................................... PAL-B/G/DK/I
VHF-Channels....................................................... 2(48.25MHz) thru E12(224.25MHz)
Tuner Ranges
2
UHF-Channels ....................................................1(471.25MHz) thru E69(855.25MHz)
Dimensions ..................................................................................................Width:446.0mm
Specifications are subject to change without prior notice.
Cabinet material ................................................................................................. All Plastics
C14-RF60
AGC &
GEOMETRIC
MODE
↓
AGC TAKE OVER POINT (AGC)
↓
VERTICAL SLOPE (V-LIN)
↓
VERTICAL AMP (V-AMP)
↓
VERTICAL SHIFT (V-CENT)
↓
HORIZONTAL SHIFT (H-CENT)
↓
EAST-WEST WIDTH (H-SIZE)
↓
HORIZONTAL PARALLELOGRAM (EW//)
↓
EAST-WEST PARABOLA/WIDTH (PARA)
↓
EAST-WEST UPPER COR. PB (COR(U))
↓
EAST-WEST LOWER COR. PB (COR(L))
↓
EAST -WEST TRAPEZIUM (TRAPE)
↓
HORIZONTAL BOW (HB)
↓
S-CORRECTION (S-COR)
WHITE POINT
ADJ.
MODE
↓
W.P RED STD. W.T. (DRI-RS)
↓
W.P. GREEN STD. W.T.(DRI-GS)
↓
W.P.BLUE STD. W.P. (DRI-BS)
↓
W.P. RED WARM W .P.(DRI-RC)
↓
W.P. GREEN WARM W .P.(DRI-GC)
↓
W.P. BLUE WARM W .P.(DRI-BC)
↓
W.P. RED COOL W.P.(DRI-RW)
↓
W.P. GREEN COOL W.P.(DRI-GW)
↓
W.P. BLUE COOL W.P. (DRI-BW)
SUB
ADJ.
MODE
↓
MAX VOLUME (SUB-VOL)
↓
SUB CONTRAST (SUB-CON)
↓
SUB COLOUR (SUB-COL)
↓
SUB BRIGHTNESS (SUB-BRI)
↓
SUB TINT (SUB-TINT)
↓
SUB SHARPNESS (SUB-SHP)
↓
MAX HOTEL VOLUME (HTL-VOL)
↓
HOTEL PROGRAM NO(HTL-PRG)
↓
OSD GRB REFERENCE (RGB)
↓
BLACK LEVEL OFFSET R(CUT-R)
↓
BLACK LEVEL OFFSET B(CUT-B)
↓
CATHODE DRIVE LEVEL(CDL)
FORWARD : CH DOWN KEY
REVERSE : CH UP KEY
* ( ) means OSD display.
FORWARD : CH DOWN KEY
REVERSE : CH UP KEY
AGC &
GEOMETRIC
MODE
WHITE POINT
ADJ.
MODE
SUB
ADJ.
MODE
Y-DELAY
ADJ.
MODE
MISC.
OPTION
MODE
IC
OPTION
MODE
OFFSET
ADJ.
MODE
3-2
SERVICE MODE
Ë
(1)In the Service Mode, Key is used to select the mode in the following order.
C bus control
2
C bus control include
2
C bus control). (Use
2
3-1
ADJUSTMENT PRECAUTIONS
This model's setting are adjusted in two different ways: through the I
and in the conventional analog manner. The adjustments via the I
preset-only items and variable data.
CAUTION:Make sure TV Set is in "Normal Condition" before switch to Service Mode for
adjustment.
1 Short JA 137 & JA 138 for 1 second and release to switch to the service mode position,
1. Setting the service mode by the microprocessor.
and the microprocessor is in input mode. (Adjustment through the I
JWS Key to set as well).
by one.
2 Press the CH DOWN / UP key on the remote controller to get ready to select the mode one
by one.
3 Press the CH DOWN / UP key on the remote controller to select the modes re v ersibly one
4 Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.
position, and the microprocessor is in out of the service mode.
5 Short JA 137 & JA 138 for 1 second and release to switch to the normal mode (OFF)
2. Factory Presetting.
Service Mode position.Initial values are automatically preset, only when a new
EEPROM is used (Judge with the first 4 bytes ).
1 Short JA 137 & JA 138 then turn "ON" the main power and release to switch to the
3
2 The initial data are preset as listed in page 5.
3 Make sure the data need modify or not (Initial data).
FIRST TIME, make sure to short JA137 & JA138 to switch to the service mode
Note: Once the chassis has been assembly together and ready to be POWER ON for the
position first and then turn on the main power switch (See 2-1 above).
Precaution: If haven't done this initiation, it may possibly generate excessive Beam
current.
(GA1 Series type RH-IX3368CE Attachment)
3. For reference please check with memory map
C14-RF60
Y-DELAY
ADJ.
MODE
↓
Y-D TIME FOR PAL (TV) (DL-PT)
↓
Y-D TIME FOR SECAM (TV) (DL-ST)
↓
Y-D TIME FOR N358 (TV) (DL-3T)
↓
Y-D TIME FOR N443 (TV) (DL-4T)
↓
Y-D TIME FOR B/W (TV) (DL-TV)
↓
Y-D TIME FOR PAL (AV) (DL-PA)
↓
Y-D TIME FOR SECAM (AV) (DL-SA)
↓
Y-D TIME FOR N358 (AV) (DL-3A)
↓
Y-D TIME FOR N443(AV) (DL-4A)
↓
Y-D TIME FOR B/W (AV) (DL-AV)
*(Y-D : Y-DELAY)
OFFSET
ADJ.
MODE
↓
COLOUR OFFSET (PAL) (COL-OP)
↓
COLOUR OFFSET (SECAM) (COL-OS)
↓
COLOUR OFFSET (NTSC358) (COL-O3)
↓
COLOUR OFFSET (NTSC443) (COL-O4)
↓
SHARPNESS OFFSET (PAL) (SHP-OP)
↓
SHARPNESS OFFSET (SECAM) (SHP-OS)
↓
SHARPNESS OFFSET (NTSC358) (SHP-O3)
↓
SHARPNESS OFFSET (NTSC443) (SHP-O4)
IC
OPTION
MODE
↓
VERTICAL SCAN DISABLE(VSD)
↓
BLACK STRETCH (BKS)
↓
AUTO V OLUME LEVELING(AVL)
↓
FAST FILTER IF-PLL(FFI)
↓
ENABLE VERTICAL GUARD (EVG)
↓
EHT TRACKING MODE (EHT)
↓
OVERSCAN SWITCH OFF(OSO)
↓
AUTO COLOUR LIMIT(ACL)
↓
FORCED COLOUR LIMIT(FCO)
MISC.
OPTION
MODE
↓
SOUND SYSTEM M (S-M)
↓
SOUND SYSTEM DK (S-DK)
↓
SOUND SYSTEM I (S-I)
↓
SOUND SYSTEM BG (S-BG)
↓
PLAYBACK SECAM (P-SECAM)
↓
FE (RF) NTSC 3.58 (F-N358)
↓
FE (RF) NTSC 4.43 (F-N443)
↓
FE (RF) SECAM (F-SECAM)
↓
VIDEO MUTE AT IDENT LOSS (VMI)
↓
VIDEO MUTE AT PROGRAM
/SOURCE CHANGE (VMC)
↓
HOTEL MODE (HTL)
↓
REDUCED FM DEMODULATION
GAIN FOR BTSC SIGNAL (BTSC)
↓
A
A
↓
NUMBER OF EXT AV SOURCE (AV)
↓
FM WINDOW SELECTION (FMWS)
↓
SOUND MUTE BIT 0 (SM0)
↓
SOUND MUTE BIT 1 (SM1)
↓
THAI LANGUAGE (THA)
↓
ARABIC LANGUAGE (ARA)
↓
MALAY LANGUAGE (MAL)
↓
CHINESE LANGUAGE (CHI)
↓
FRENCH LANGUAGE (FRE)
↓
RUSSIAN LANGUAGE (RUS)
↓
FORCED V-SYNC SLICING LEVEL(FSL)
↓
SYNC OF OSD (HP2)
↓
TUNER SELECTION (CPT)
↓
B
↓
BILINGUAL(BIL)
↓
IF AGC SPEED BIT 0 (AGC0)
↓
IF AGC SPEED BIT 1 (AGC1)
↓
FOA Time Constant-RF (FOA-FE)
↓
FOB Time Constant-RF (FOB-FE)
↓
FOA Time Constant-AV (FOA-AV)
↓
FOB Time Constant-AV (FOB-AV)
↓
LED BLINK SPEED (LED-F)
↓
VOLUME CONTROL TABLE (MSA)
↓
OUTPUT VERTICAL GUARD (NDF)
B
4-2
FUNCTION AGC
RC COMMAND SERVICE-ITEM
CONTRAST DOWN V-LIN
* Direct Key-in for service item in service mode
TINT DOWN H-CENT
COLOUR DOWN V-AMP
SHARPNESS DOWN EW / /
BRIGHTNESS DOWN V-CENT
TIMER SUB-VOL
SYSTEM HB
BLUEBACK S-COR
CONTRAST UP SUB-CON
TINT UP SUB TINT
COLOUR UP SUB-COL
BRIGHTNESS UP SUB-BRI
SHARPNESS UP SUB-SHP
4-1
4
REMARK
C14-RF60
INITIAL DATA FIX/ADJ
EEPROM ITEMS OSD DATA LENGTH
SHARPNESS OFFSET (NTSC443) SHP-O4 0~15 8 *FIX
VERTICAL SCAN DISABLE VSD 0(DISABLE)/1(ENABLE) 0 *FIX
BLACK STRETCH BKS 0(DISABLE)/1(ENABLE) 1 *FIX
AUTOMATIC VOLUME LEVELING AVL 0(DISABLE)/1(ENABLE) 1 *FIX
FAST FILTER IF-PLL FFI 0(DISABLE)/1(ENABLE) 0 *FIX
ENABLE VERTICAL GUARD (RGB BLANKING) EVG 0(DISABLE)/1(ENABLE) 1 *FIX
EHT TRACKING MODE (HCO) EHT 0(DISABLE)/1(ENABLE) 1 *FIX
OVERSCAN SWITCH OFF OSO 0(DISABLE)/1(ENABLE) 0 *FIX
AUTO COLOUR LIMIT ACL 0(DISABLE)/1(ENABLE) 0 *FIX
FORCED COLOUR LIMIT FCO 0(DISABLE)/1(ENABLE) 0 *FIX
CHG *4
CHG *5
5-2
BTSC 0(DISABLE)/1(ENABLE) 0 *FIX
Please set the EEPROM initial data according to the value in parenthesis ( ) before adjustment.
1) *FIX: PLEASE DO NOT CHANGE FIXED DATA WITHOUT SPECIFIC INSTRUCTION.
SOUND SYSTEM M S-M 0(DISABLE)/1(ENABLE) 0
SOUND SYSTEM DK S-DK 0(DISABLE)/1(ENABLE) 1 *FIX
SOUND SYSTEM I S-I 0(DISABLE)/1(ENABLE) 1 *FIX
SOUND SYSTEM BG S-BG 0(DISABLE)/1(ENABLE) 1 *FIX
PLA YBACK SECAM P-SECAM 0(DISABLE)/1(ENABLE) 1 *FIX
FE (RF) NTSC 3.58 F-N358 0(DISABLE)/1(ENABLE) 0
FE (RF) NTSC 4.43 F-N443 0(DISABLE)/1(ENABLE) 1 *FIX
FE (RF) SECAM F-SECAM 0(DISABLE)/1(ENABLE) 1 *FIX
VIDEO MUTE AT IDENT LOSS VMI 0(DISABLE)/1(ENABLE) 1 *FIX
VIDEO MUTE AT PROGRAM/SOURCE CHANGE VMC 0(DISABLE)/1(ENABLE) 1 *FIX
HOTEL MODE HTL 0(DISABLE)/1(ENABLE) 0 *FIX
REDUCED FM DEMODULATOR GAIN FOR BTSC SIGNAL
NUMBER OF EXTERNAL AV SOURCE AV 0 FOR1 AV/1 FOR 2AV 1 (0) *FIX
FM WINDOW SELECTION FMWS 0(DISABLE)/1(ENABLE) 0 *FIX
SOUND MUTE BIT 0 SM0 0(DISABLE)/1(ENABLE) 1 *FIX
SOUND MUTE BIT 1 SM1 0(DISABLE)/1(ENABLE) 0 *FIX
THAI LANGUAGE THA 0(DISABLE)/1(ENABLE) 0 *FIX
ARABIC LANGUAGE ARA 0(DISABLE)/1(ENABLE) 1 *FIX
MALAY LANGUAGE MAL 0(DISABLE)/1(ENABLE) 1 *FIX
CHINESE LANGUAGE CHI 0(DISABLE)/1(ENABLE) 1 *FIX
FRENCH LANGUAGE FRE 0(DISABLE)/1(ENABLE) 1 *FIX
RUSSIAN LANGUAGE RUS 0(DISABLE)/1(ENABLE) 1 *FIX
FORCED V-SYNC SLICING LEVEL FSL 0(DISABLE)/1(ENABLE) 0 *FIX
SYNC OF OSD HP2 0(DISABLE)/1(ENABLE) 0 *FIX
TUNER SELECTION (0:SHARP/ALPS;1:MURATA) CPT 0(DISABLE)/1(ENABLE) 0 *FIX
BILINGUAL BIL 0(DISABLE)/1(ENABLE) 0 *FIX
IF AGC SPEED BIT 0 AGC0 0(DISABLE)/1(ENABLE) 1 *FIX
IF AGC SPEED BIT 1 AGC1 0(DISABLE)/1(ENABLE) 0 *FIX
PHI-1 TIME CONSTANT (RF) FOA-FE 0(DISABLE)/1(ENABLE) 0 *FIX
PHI-1 TIME CONSTANT (RF) FOB-FE 0(DISABLE)/1(ENABLE) 0 *FIX
PHI-1 TIME CONSTANT (OFF AIR) FOA-AV 0(DISABLE)/1(ENABLE) 1 *FIX
PHI-1 TIME CONSTANT (OFF AIR) FOB-AV 0(DISABLE)/1(ENABLE) 1 *FIX
LED BLINK SPEED LED_F 0(DISABLE)/1(ENABLE) 0 (1) *FIX
VOLUME CONTROL PWM TABLE MSA 0(DISABLE)/1(ENABLE) 0 (1) *FIX
OUTPUT VERTICAL GUARD NDF 0(DISABLE)/1(ENABLE) 0 (1) *FIX
NOTE :
COLOUR OFFSET (PAL) COL-OP : 8 ------> 14
COLOUR OFFSET (SECAM) COL-OS : 8 ------> 14
COLOUR OFFSET (NTSC358) COL-O3 : 4 ------> 10
COLOUR OFFSET (NTSC443) COL-O4 : 4 ------> 10
2) *1: S-COR ADJUST=17
3) *2: CDL ADJUST=5
4) *3: ADJUST COLOUR OFFSET AFTER ADJUST SUB-COLOUR
5) *4: ADJUST S-M=1
6) *5: F-N358=1
7) *6: DL-3T=8
8) *7: SUB-CON=52
9) *8: RGB=6
Address Data Address Data
00H: 55H 02H: 43H
REMARK
SAME AS (DRI-BS) DATA
INITIAL DATA FIX/ADJ
5-1
EEPROM ITEMS OSD DATA LENGTH
01H: 4FH 03H: A1H
After short JA137& JA138, and turn on the main power switch, read data from EEPROM
address 00H ~ 03H, and compare to the list below, if different, initialize the EEPROM.
AGC TAKE OVER POINT AGC 0~63 14 ADJ
VERTICAL SLOPE V-LIN 0~63 32 ADJ
VERTICAL AMPLITUDE V-AMP 0~63 32 ADJ
VERTICAL SHIFT V-CENT 0~63 32 ADJ
HORIZONTAL SHIFT H-CENT 0~63 32 ADJ
EAST-WEST WIDTH H-SIZE 0~63 32 *FIX
HORIZONTAL PARALLELOGRAM EW// 0~63 32 *FIX
EAST-WEST PARABOLA/WIDTH PARA 0~63 32 *FIX
EAST-WEST UPPER CORNER PARABOLA COR (U) 0~63 32 *FIX
EAST-WEST LOWER CORNER PARABOLA COR (L) 0~63 32 *FIX
EAST -WEST TRAPEZIUM TRAPE 0~63 32 *FIX
HORIZONTAL BOW HB 0~63 32 *FIX
S-CORRECTION S-COR 0~63 0 CHG *1
WHITE POINT RED STD WHITE TEMP DRI-RS 0~63 32 *FIX
WHITE POINT GREEN STD WHITE TEMP DRI-GS 0~63 32 ADJ
WHITE POINT BLUE STD WHITE TEMP DRI-BS 0~63 32 ADJ
WHITE POINT RED COOL WHITE TEMP DRI-RC 0~63 25 ADJ
WHITE POINT GREEN COOL WHITE TEMP DRI-GC 0~63 32 ADJ (DRI-GS)-7 DATA
WHITE POINT BLUE COOL WHITE TEMP DRI-BC 0~63 32 ADJ
WHITE POINT RED W ARM WHITE TEMP DRI-RW 0~63 32 *FIX
WHITE POINT GREEN WARM WHITE TEMP DRI-GW 0~63 32 ADJ (DRI-GS)-7 DATA
WHITE POINT BLUE WARM WHITE TEMP DRI-BW 0~63 32 ADJ (DRI-BS)-7 D AT A
MAX VOLUME SUB-VOL 0~63 63 *FIX
SUB CONTRAST SUB-CON 0~63 63 CHG *7
SUB COLOUR SUB-COL 0~63 32 ADJ
SUB BRIGHTNESS SUB-BRI 0~63 32 ADJ
SUB TINT SUB-TINT 0~63 32 ADJ
SUB SHARPNESS SUB-SHP 0~63 32 (20) *FIX
MAX HOTEL VOLUME HTL-VOL 0~63 32 *FIX
HOTEL PROGRAM NUMBER HTL-PRG 0~99 OR>99FOR NONE 255 *FIX
OSD GRB REFERENCE RGB 0~15 15 CHG *8
BLACK LEVEL OFF-SET R CUT-R 0~63 32 ADJ
BLACK LEVEL OFF-SET G CUT-G 0~63 32 ADJ
CATHODE DRIVE LEVEL CDL 0~15 0 CHG *2
Y-DELAY TIME FOR PAL(TV) [YD] DL-PT 0~15 12 *FIX
Y-DELAY TIME FOR SECAM(TV) [YD] DL-ST 0~15 15 *FIX
Y-DELAY TIME FOR N358 (TV) [YD] DL-3T 0~15 12 CHG *6
Y-DELAY TIME FOR N443 (TV) [YD] DL-4T 0~15 12 *FIX
Y-DELAY TIME FOR B/W (TV) [YD] DL-TV 0~15 12 *FIX
Y-DELAY TIME FOR PAL (AV) [YD] DL-PA 0~15 12 *FIX
Y-DELAY TIME FOR SECAM (AV) [YD] DL-SA 0~15 15 *FIX
Y-DELAY TIME FOR N358 (AV) [YD] DL-3A 0~15 12 *FIX
Y-DELAY TIME FOR N443 (AV) [YD] DL-4A 0~15 12 *FIX
Y-DELAY TIME FOR B/W (AV) [YD] DL-AV 0~15 12 *FIX
COLOUR OFFSET (PAL) COL-OP 0~15 8 CHG *3
COLOUR OFFSET (SECAM) COL-OS 0~15 8 CHG *3
COLOUR OFFSET (NTSC358) COL-O3 0~15 4 CHG *3
COLOUR OFFSET (NTSC443) COL-O4 0~15 4 CHG *3
SHARPNESS OFFSET (PAL) SHP-OP 0~15 8 *FIX
SHARPNESS OFFSET (SECAM) SHP-OS 0~15 4 *FIX
SHARPNESS OFFSET (NTSC358) SHP-O3 0~15 12 (8) *FIX
5
C14-RF60
PROM follow by INITIAL setting.
2
6-2
ITEMS DATA SETTING
LAST PROGRAM/CHANNEL 1
FLASHBACK PROGARM/CH 1
DIGIT 1
C-SYSTEM AUTO
VOLUME 1
S-SYSTEM *1
AFC ON
SKIP OFF
COLOUR (CENTER)
CONTRAST (MAX)
TINT (CENTER)
SHARPNESS (CENTER)
BRIGHTNESS (CENTER)
WHITE TEMP STANDARD
REMINDER TIMER In-active, "--:--"
ON TIMER In-active, "--:--"
OFF TIMER In-active, "--:--"
LAST POWER POWER-ON
LANGUAGE *1
BLUE BACK MUTE ON
HOTEL MODE OFF
LAST TV/AV TV
0 CHANNEL SKIP ON
SHIPPING SETTING & CHECKING
(1)The following default data has been factory-set for the E
2 CHINESE I
3 ENGLISH B/G
INITIAL LANGUAGE SOUND SYSTEM
*1:Please refer defaults for LANGUAGE and SOUND SYSTEM per MODEL as follows.
"20,000" "40,000" 12300K CHINESE I 6
"35,000" "30,000" 12300K ENGLISH B/G 6
DESTINATION MAGNETIC FIELD (V, H) nT BACKGROUND LANG. S-SYS LANG QTY
HONGKONG (051)
FACTORY SETTING BY MODEL
JAPAN TOURIST (981J)
(Reference: Geomagnetism Adjustment)
LANGUAGE QTY: ENGLISH/CHINESE/FRENCH/ARABIC/MALAY/RUSSIAN
MCL1
INITIAL SHIPPING SETTING FOR PRESET TUNING
(1)Please set the MCL1.
(2)After set the MCL1, please set the INITIAL SETTING for each model.
INITIAL 2: Hong Kong models.
INITIAL 3: Japan Tourist models.
0 41.10
1 48.25 B/G
2 62.25 B/G
CH-NO Fv (MHz) SOUND SYS
3 77.25 D/K
4 175.25 B/G
5 182.25 B/G
6 183.25 D/K
7 191.25 D/K
8 196.25 B/G
6-1
9 199.25 M
10 210.25 B/G
11 224.25 B/G
12 471.25 B/G
13 487.25 I
14 503.25 B/G
15 575.25 B/G
16 583.25 B/G
17 599.25 B/G
18 621.25 M
19 639.25 D/K
20 703.25 B/G
21 735.25 I
22 767.25 B/G
23 815.25 B/G
24 855.25 I
25 855.25 B/G
26 55.25 M
27 83.25 M
28 183.25 M
29 193.25 M
30 217.25 M
31 471.25 M
32 477.25 M
33 693.25 M
34 41.10
35 112.25 B/G
36 168.25 B/G
37 41.10
38 294.25 B/G
39 463.25 B/G
40 41.10
41 647.25 B/G
42 663.25 B/G
43 679.25 B/G
44 174.95 B/G
45 175.55 B/G
46 41.10
The Sound System of above channels will be changed accordingly, after pressing INITIAL key.
*
For example; pressing INITIAL2 and 3, all Sound Systems will be set to I and B/G.
6
C14-RF60
» Bias box: About 4.5 V
Oscilloscope
0.1V
TV Set
Bias box
TP201+
+
—
—
E-9 CH
P C
10k
100k
1n60
75ohm
IF OUT
-1.5+/-0.8dB
1000p
Oscilloscope
a
b
A
B
A
B
A = B
A = B
Rank "A"
(on the right of the CRT)
Rank "A"
(on the left of the CRT)
Green-only
Blue-only
Red-only
Signal-colour
screen cleared
Fig. 4-1
PURITY ADJUSTMENT
the beam current to about 500 µA.
coil.
adjust the magnetic field.
netic field and keep the static convergence
roughly adjusted.
through the microscope. Adjust the landing to
1. Receive the GREEN-ONLY signal. Adjust
2. Degauss the CRT enough with the degausing
Note: Follow the Job Instruction Sheet to
PURITY ADJ.
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
3. Maintain the purity magnet at the zero mag-
4. Observe the points a, b as shown in Fig. 4-1
the rank A requirements.
5. Orient the raster rotation to 0 eastward.
warming up the unit for 30 minutes
» Tightening torque: 108 ± 20 N (11 ± 2 kgf)
A rank requirements. If not, stick the magnet
sheet to correct it.
6. Tighten up the deflection coil screws.
Note:This adjustment must be done after
7. Make sure the CRT corners landing meet the
or longer with a beam current over
Fig. 4-2
500 µA.
* For the following colours press R/C RGB key to
Fig. 4-3
7-2
change.
PIF ADJUSTMENT
signal,but with no signal input.
to the tuner antenna. ( RF SWEEP )
Adjust the PLL data.
2.Connect the sweep generator's output cable
3.Adjust the sweep generator's to 80dBuV.
4. Connect the response lead ( use LOW IM-
NO. Adjustment part Adjusting procedure and conditions Waveform and others
1.Get the tuner ready to receive the CH. E - 9
Tuner IFT
(PRESET)
1
Fig. 1
PEDANCE probe with wave detector ; see
Fig.1 ) to the tuner's IF output terminal.
nected ).
( This terminal must have the probe alone con-
5.Set the RF AGC to 0 - 6 V with no saturation
Fig. 2
For the 50 ohm signal strength
gauge, when not using 50/75
impedance adapter, signal
strength is 52 ±1 dBµV(75 ohm
open), instead of 57±1 dBµV
(75 ohm open).
The loss of using impedance
Note:
adapter
Precaution:
7-1
Fig. 3
during this adjustment.
as shown in Fig. 2.
Be sure to keep the tuner cover in position
Note:
» Signal Strength: 57 ±1 dBµV (75 ohm open)
AGC Terminal) as shown in Fig. 3.
1. Receive "PAL COLOUR BAR" signal.
2. Connect the oscilloscope to TP201 (Tuner’s
C BUS
RF-AGC
2
TAKE OVER
POINT
ADJUSTMENT
(I
CONTROL)
2
"AGC" bus data to obtain the Tuner output pin
drop 0.1 V below maximum voltage.
63~67dBµV , and make sure there is no noise .
3. Call "AGC" mode in service mode. Adjust the
sure that there is no cross modulation beat.
4. Change the antenna input signal to
5. Turn up the input signal to 90~95 dBµV to be
with the waveform.
6.Adjust the tuner IF coil to obtain the waveform
7
C14-RF60
t
3.3Vdc
0
RGB
BGR
R
G
B
R
G
B
B
G
R
B
G
R
RGB
BGR
Lacquer
Wedge "a"
Wedge
"b"
Wedge
"c"
About
100°
About
100°
4-pole magnet
6-pole magnet
CRT neck
Lacquer
Purity magnet
Note***
1 2 3 4 5
1 2 3 4 5
* Alternative Procedure:
(1) Step (1), (2), (3) and (4) are same
1. Before CRT cutoff adjustment, SUB-BRIGHT,
Remark
our appear whether red, green or
blue.
as beside procedure.
(2) Then continue adjust until retrace
DRI-RS/RW/RC, DRI-GS/GW/GC, DRI-BS/BW/
BC,
test points as below which is based
line appear and make sure the col-
(3) Connect the oscilloscope to related
CUT-R and CUT-G must be INITIAL DATA.
room.
2. CRT Cutoff adjustment must be done inside a dark
1. Switch TV to VIDEO mode,BLUE BACK OFF, with
of signal reach 3.3Vdc.
on colour appear at (2) RED =
TP47R, GREEN = TP47G, BLUE =
TP47B.
(4) Then adjust Screen VR until the tip
NO VIDEO signal.
tor.
crease screen variable resistor until colour raster
suddenly on and off (AKB start function).
tor until screen retrace line cut off. (Not Raster)
2. Press R/C to set Picture Normal condition.
3. First, off the screen by adjust screen variab le resis-
*4. Next, checking AKB circuit function by slowly in-
5. Then continue adjust until retrace line appear.
6. Finally, slowly decrease the screen variable resis-
Must confirm the AKB function in set before con-
Note :
1
hatch pattern with 5 black level windows)
tinue the next adjustment.
1. Call " SUB-BRI" in service mode. (Receive Cross-
2. Adjust the " SUB BRIGHT " bus data in order that
Y : 0.275
# 12300°K X : 0.272
2
Line 3 is one step (data) brighter than line 2
the line 1and 2 have the same darkness wherelse
line 3 is one step (data) brighter than line 2. Fi-
nally data minus 1 to make line 1, 2, and 3 are in
same level (darkness).
3. Clear the SERVICE mode.
(MINOL T A COLOUR ANALYZER CA-
) TP603 (+).
1. Receive the "WHITE" pattern with BURST signal.
2. Press R/C to set Picture NORMAL condition.
3. Connect the DC miliammeter between TP602 (-
DRI-BW="DRI-BS"-7
DRI-GC="DRI-GS"-7
LOW HIGH
10cd/m2 200cd/m2
by Volume key .
100)
*Note: Above Data can be UP/DOWN
DRI-BS data to have a colour temperature of
12300°K ( white ). * Note .
and set BRIGHTNESS Y b y generator, to **10 cd/
m2 (MINOLTA CA-100) by reducing LUMINANCE
Y signal.
temperature #. Then go back NORMAL mode
4. Check Beam current should be around 800 µA.
5. Set it to service mode and adjust the DRI-GS, &
6. Receive "WHITE" pattern, WITH BURST signal,
(HIGH BRIGHT) to check colour temperature. If
7. Adjust "CUT-R" & "CUT-G" to get desired colour
DRI-RC=25
* 12300°K DRI-GW="DRI-GS"-7
ing up the unit for 30 minutes or longer with
a beam current over 500µA.
out of range, back to (1).
Note:This adjustment must be done after warm-
& TP602 (–).
DATA, after finishing DRI-BS and DRI-GS DATA
ADJUSTMENT.
* ADJUST DRI-GC/GW, DRI-BC/BW as following
DRI-RW = 32 (FIXED), DRI-RS = 32 (FIXED)
DRI-BC = "DRI-BS"
(Full Scale: 3 mA Range)
1. Receive the "Monoscope Pattern" signal.
2. Press R/C to set Picture NORMAL condition.
3. Connect the DC miliammeter between TP603 (+)
8-2
4. Beam current must be within 800 ± 100 µA.
C BUS
2
CONTROL)
CRT CUTOFF
ADJUSTMENT
CRT CUT-OFF, BACKGROUND AND SUB-CONTRAST ADJUSTMENT
(I
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
Fig. 5-1
Fig. 5-2
C BUS
2
SUB-
BRIGHTNESS
ADJUSMENT
(I
2
Fig. 5-3
CONTROL)
WHITE
BALANCE
3
Fig. 5-4
C BUS
2
SERVICE
MODE ADJ
(I
CONTROL)
Note***
SAMSUNG CRT: 32mm
CPT CRT : 35mm
TOSHIBA CRT : 35mm
Maximum
4
beam check
8-1
1. Receive the "Crosshatch Pattern" signal.
2. Using the remote controller, call NORMAL
CONVER-
GENCE ADJ.
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
mode.
(To be done
CONVERGENCE ADJUSTMENT
angle in order to superpose the blue and red
colours.
angle in order to superpose the green colour
STATIC CONVERGENCE
1. Turn the 4-pole magnet to a proper opening
after the purity
adjustment.)
over the blue and red colours.
2. Turn the 6-pole magnet to a proper opening
screen in the following steps.
a) Fig. 5-1: Drive the wedge at point "a" and
DYNAMIC CONVERGENCE
1. Adjust the convergence on the fringes of the
swing the deflection coil upward.
and swing the deflection coil downward.
b) Fig. 5-2: Drive the wedge at points "b" and "c"
swing the deflection coil rightward.
swing the deflection coil leftward.
c) Fig. 5-3: Drive the "c" wedge deeper and
d) Fig. 5-4: Drive the "b" wedge deeper and
screw, magnet unit (purity, 4-pole, 6-pole
magnets) and magnet unit lock screw.
tape over them.
2. Fix all the wedges on the CRT and apply glass
3. Apply lacquer to the deflection yoke lock
8
Finally received the Red-only and Blue-only
signals to make sure there is no other colours
on the screen.
Cy
G
B
W
Y 100%W
75%
Mg R
Fig. 7-1
W
Y
Cy G Mg R
B
SAME LEVEL
each short test.
* Select one of Q883/5/7 to do
C14-RF60
9-2
5) BLUE-OUT.
NTSC CHROMA ADJUSTMENT
thru AV in.
1. Receive the "NTSC 3.58 Colour Bar" signal
SUB-TINT
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
» Range : 100mV/div. (AC)(Use Probe
2. Connect the oscilloscope to TP47B (P882 pin
C BUS
2
(I
CONTROL)
Adjust the "SUB-TINT" bus data to obtain the
10:1)
» Sweep time : 10 µsec/div.
3. Call the "SUB-TINT" mode in ser vice mode.
waveform shown as Fig. 7-1.
4. Clear the SERVICE mode.
short, make sure the protector ON and switch
1. Receive "Monoscope Pattern" signal.
2. Set CONTRAST MAX.
to standby mode.
3. Set BRIGHT MAX.
4. Dur ing the Collector & Emitter of Q883/5/7
1. Receive "Monoscope Pattern" signal.
PROTECTOR OPERATION CHECKING
BEAM
PROTECTOR
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
H. V PROTEC2
the protector is not working.
3. Set voltage of Bias Bo x to 18V and make sure
the protector is working.
4. Set voltage of Bias Box to 27V, and make sure
(R610 side).
2. Connect output of Bias Box to D603 cathode
TOR
testing in +B line, check all possible damaged
components on +B line.
1. Once finish rectified Electrolytic Capacitor short
Other
protectors
3
(Use random selected set for inspection)
White Colour Bar, Sound 400 Hz 100% Mod).
pedance. Make sure the output is as speci-
fied (1.0 Vp-p ±3 dB).
1. Receive the "PAL Colour Bar" signal (100%
2. Terminate the Video output with a 75 ohm im-
impedance. Make sure the O/P is as speci-
3. Terminate the Audio output with a 10k ohm
make sure that the modes change in order of
TV, AV & TV again and the video & audio out-
put are according to the input terminal for each
mode.If connect input to Front and Rear AV
terminal, input terminal of Front AV will be se-
fied (1.76 Vp-p ±3 dB).
1. Using the TV/AV key on the remote controller,
lected.
A/V INPUT AND OUTPUT CHECKING
VIDEO AND
AUDIO OUT-
NO. Adjustment part Adjusting procedure and conditions Waveform and others
PUT CHECK
1
VIDEO AND
AUDIO INPUT
CHECK
2
Fig. 6-1
9-1
to set overscan of 9.5% typical.
till the horizontal line in the center of
monoscope is just at the position where the
1. Receive Monoscope Pattern Signal.
2. Call the "V-LIN" mode.
HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENT
C BUS
2
V-LIN
(I
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
blanking starts.
3. Increase or decrease "V-LIN" by Volume key
CONTROL)
till the picture is centered.
1. Call the "V-CENT" mode.
2. Increase or decrease "V -CENT" by V olume key
C BUS
2
CONTROL)
V-CENTER
(I
2
1. Call the "V-AMP" mode.
2. Increase or decrease "V -AMP" by V olume key
C BUS
2
V-AMP
(I
3
CONTROL)
Adjustment Spec 9.5% range +1% -0%.
key to center the picture horizontal.
1. Call the "H-CENT" mode.
2. Increase or decrease "H-CENT" by Volume
C BUS
2
H-CENTER
(I
CONTROL)
4
re-adjust V-Slope, V-Shift and V-Amp to
makesure adjustment is in acceptable Ring-
1. SET DATA TO 17.
* Check the E-5 CH Monoscope Pattern then
C BUS
2
S-CORREC-
TION (I
CONTROL)
5
Shaped.
1. Receive the "Monoscope Pattern" signal.
1. SET DATA TO 20.
SUB-
SHARPNESS
1 Focus
6
9
PAL CHROMA ADJUSTMENT
ing.
2. Press R/C to set Picture NORMAL condition.
3. Adjust the focus control to get the best focus-
NO. Adjustment part Adjusting procedure and conditions Waveform and others
Red cathode(D881 Cathode).
1. Receive the "PAL Colour Bar" signal.
2. Press R/C to set Picture Normal condition.
C BUS
2
SUB COLOUR
(I
1
probe)
3. Connect the oscilloscope to
» Range : 20 V/div. (AC) (Using 10:1
» Sweep time : 10 µsec/div.
4. Using the R/C call "SUB COL" in SERVICE
CONTROL)
mode. Adjust SUB COLOUR b us data, so that
the 75% White & Red portions of PAL Color
Bar be at the same level shown as Fig. 6-1.
Before adjust SUB-COL, make sure COL-
OP=8, COL-OS88, COL-03=4, COL-04=4.
set.
COL-OP : 8 ------> 14 COL-O3 : 4 ------> 10
COL-OS : 8 ------> 14 COL-O4 : 4 ------> 10
5. After adjust SUB-COLOUR, change colour off
6. Clear the SERVICE mode.
C14-RF60
(Continued)
press the COLOUR SYSTEM key to select
modes except P AL, chec k the COLOUR is not
working properly. Then, select the "P AL" mode.
Check again its colour so that it is working
properly.
press COLOUR SYSTEM key to select modes
except SECAM, check the COLOUR is not
working properly. Then, select the "SECAM"
1. Receive the "PAL COLOUR BAR" signal,
2. Receive "SECAM COLOUR BAR" signal,
mode. Chec k again its colour so that it is work-
ing properly.
signal, press COLOUR SYSTEM key to se-
lect modes except N4.43/3.58, check the
COLOUR is not working properly. Then, se-
lect the "NTSC 4.43/3.58" mode. Check again
its colour so that it is working properly.
signal thru AV, press COLOUR SYSTEM key
to select modes except N4.43/3.58, check the
COLOUR is not working properly. Then, se-
lect the "NTSC 4.43/3.58" mode. Check again
3. Receive "NTSC 4.43/3.58 COLOUR BAR"
4. Receive "NTSC 4.43/3.58 COLOUR BAR"
its colour so that it is working properly.
SYSTEM" to select B/G, I. Check the sound
output is not working properly. Select D/K and
check the sound output to make sure it is work-
ing properly.
SYSTEM" to select B/G, D/K. Check the sound
output is not working properly. Select I and
check the sound output to make sure it is
working properly.
SYSTEM" to select I, D/K. Check the
1. Receive "PAL-D/K" signal, press the "SOUND
2. Receive "PAL-I" signal, press the "SOUND
sound output is not working properly. Select
3. Receive "PAL-B/G" signal, press the "SOUND
sure the sound is heard from the speakers.
B/G and check the sound output to make sure
it is working properly.
SYSTEM" to select B/G, D/K and I, check the
sound output is not working properly. Select
M and check the sound output to make sure it
4. Receive "NTSC-M" signal, press the "SOUND
is working properly.
Then put the unit in no signal state.
1. Receive "PAL COLOUR BAR" signal.
2. T urn up the volume control to maximum, make
3. Check the sound mute is effective.
Check OSD LANGUAGE quantity and type as
English, Russian, Chinese, French, Arabic and
4. Finally turn sound level of CTV to minimum.
Malay.
10-2
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
NO. Adjustment part Adjusting procedure and conditions Waveform and others
COLOUR
SYSTEM
9
SOUND
SYSTEM
10
contrast, colour , bright, tint
Note:If nothing is display mean
or sharpness are all in nor-
mal setting.
NOISE MUTE
CHECKING
11
OSD
12
LANGUA GE
QUANTITY
CHECK
10-1
1. Receive "Monoscope Pattern" signal.
CONTRAST
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
the CONTRAST effect is OK or not.
2. Set P-Mode to select CONTRAST.
3. Press Volume Up/Down key to chec k whether
key
the COLOUR effect is OK or not.
1. Receive "Color Bar" signal.
2. Set P-Mode to select COLOUR.
3. Press V olume Up/Down k ey to check whether
2 COLOUR key
the BRIGHTNESS effect is OK or not.
1. Receive "Monoscope Pattern" signal.
2. Set P-Mode to select BRIGHTNESS.
3. Press V olume Up/Down k ey to check whether
BRIGHTNESS
key
3
UP for GREEN direction and DOWN f or PUR-
1. Receive the "NTSC Colour Bar" signal.
4 TINT key
PLE direction whether is OK or not.
2. Set P-Mode to select TINT.
3. Press Volume Up/Down key to check TINT,
the SHARPNESS effect is OK or not.
1. Receive "Monoscope Pattern" signal.
2. Set P-mode to select SHARPNESS.
3. Press V olume Up/Down k ey to check whether
SHARPNESS
Key
5
10
channel number in green colour under AFT
ON condition.
1. All Ch (1~99) will have an OSD display of the
CH DISPLA Y
COLOUR
6
is pressed, all the settings will be present to
1. Once in PICTURE Mode, and theNORMAL key
7 NORMAL Key
normal setting.
(Normal setting value for every mode).
» CONTRAST : MAX
1. Receive "Monoscope Pattern" signal.
2. Set FUNCTION to select WHITE TEMP .
» COLOUR : CENTER
» BRIGHTNESS : CENTER
» TINT : CENTER
» SHARPNESS : CENTER
3. Press Volume Up/Down key to check WHITE
8 White Temp
TEMP Option, STANDARD:
NORMAL SETTING, WARM for more RED-
DISH direction changing, COOL for more
BLUISH direction changing.
C14-RF60
PASS WORD
55 00-FF
PASS WORD
4F 00-FF
PASS WORD
43 00-FF
PASS WORD
A1 00-FF
AGC TAKE-OVER
0E 00-3F
V-SLOPE
20 00-3F
V-AMPLITUDE
20 00-3F
V-CENTER
20 00-3F
H-CENTER
20 00-3F
H-SIZE
20 00-3F
EW-PARALLELOGRAM
20 00-3F
EW-PARABOLA/WIDTH
20 00-3F
EW-UPPER CORNER
20 00-3F
EW-LOWER CORNER
20 00-3F
EW-TRAPEZIUM
20 00-3F
HORIZONTAL-BOW
20 00-3F
S-CORRECTION
00 00-3F
DRIVE-R (STANDARD)
20 00-3F
DRIVE-G (STANDARD)
20 00-3F
DRIVE-B (STANDARD)
20 00-3F
DRIVE-R (WARM)
20 00-3F
DRIVE-G (WARM)
20 00-3F
DRIVE-B (WARM)
20 00-3F
DRIVE-R (COOL)
19 00-3F
DRIVE-G (COOL)
20 00-3F
DRIVE-B (COOL)
20 00-3F
SUB-VOLUME
3F 00-3F
SUB-CONTRAST
3F 00-3F
SUB-COLOUR
20 00-3F
SUB-BRIGHTNESS
20 00-3F
SUB-TINT
20 00-3F
SUB-SHARPNESS
20 00-3F
HTL-VOLUME
20 00-3F
HTL-POSITION
FF 00-FF
OSD-REFERENCE
0F 00-0F
CUTOFF LEVEL -OFFSET R
20 00-3F
CUTOFF LEVEL -OFFSET G
20 00-3F
CATHODE DRIVE LEVEL
00 00-0F
Y-DELAY (TV PAL)
0C 00-0F
Y-DELAY (TV SECAM)
0F 00-0F
Y-DELAY (TV N358)
0C 00-0F
Y-DELAY (TV N443)
0C 00-0F
Y-DELAY (TV BW)
0C 00-0F
Y-DELAY (AV PAL)
0C 00-0F
Y-DELAY (AV SECAM)
0F 00-0F
Y-DELAY (AV N358)
0C 00-0F
Y-DELAY (AV N443)
0C 00-0F
Y-DELAY (AV BW)
0C 00-0F
COLOUR-OFFSET (PAL)
08 00-0F
COLOUR-OFFSET (SECAM)
08 00-0F
COLOUR-OFFSET (N358)
04 00-0F
COLOUR-OFFSET (N443)
04 00-0F
SHARPNESS-OFFSET (PAL)
08 00-0F
MODEL
LETTER NO.
(1) 20th August
2001:Change of
range & default.
MICON EEPROM EEPROM CHASSIS CTV FINAL
LAST INITIAL
SETTING DATA
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
DEFAULT RANGE
WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
REMARK
ADDRESS
DATA
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
MODEL
LETTER NO.
11-2
MEMORY MAP
100% MODULATION (±50KHz Dev)
output with 400Hz sound and no sound out
HEADPHONE JACK CHECKING
1. Receive PAL Colour P AR with SOUND 400Hz
from speaker
2. Maximun volume, and check the headpone
11-1
HEDPHONE
OUTPUT
CHECKING
1
NO. Adjustment part Adjusting procedure and conditions Waveform and others
11
C14-RF60
ADDRESS
DATA
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
80
TUNING FREQUANCY (HIGHER PART)
POS 4
81
TUNING FREQUANCY (LOWER PART)
82
S-SYS AFT (auto) C-SYS
83
TUNING FREQUANCY (HIGHER PART)
POS 5
84
TUNING FREQUANCY (LOWER PART)
85
S-SYS AFT (auto) C-SYS
86
TUNING FREQUANCY (HIGHER PART)
POS 6
87
TUNING FREQUANCY (LOWER PART)
88
S-SYS AFT (auto) C-SYS
89
TUNING FREQUANCY (HIGHER PART)
POS 7
8A
TUNING FREQUANCY (LOWER PART)
8B
S-SYS AFT (auto) C-SYS
8C
TUNING FREQUANCY (HIGHER PART)
POS 8
8D
TUNING FREQUANCY (LOWER PART)
8E
S-SYS AFT (auto) C-SYS
8F
TUNING FREQUANCY (HIGHER PART)
POS 9
90
TUNING FREQUANCY (LOWER PART)
91
S-SYS AFT (auto) C-SYS
92
TUNING FREQUANCY (HIGHER PART)
POS 10
93
TUNING FREQUANCY (LOWER PART)
94
S-SYS AFT (auto) C-SYS
95
TUNING FREQUANCY (HIGHER PART)
POS 11
96
TUNING FREQUANCY (LOWER PART)
97
S-SYS AFT (auto) C-SYS
98
TUNING FREQUANCY (HIGHER PART)
POS 12
99
TUNING FREQUANCY (LOWER PART)
9A
S-SYS AFT (auto) C-SYS
9B
TUNING FREQUANCY (HIGHER PART)
POS 13
9C
TUNING FREQUANCY (LOWER PART)
9D
S-SYS AFT (auto) C-SYS
9E
TUNING FREQUANCY (HIGHER PART)
POS 14
9F
TUNING FREQUANCY (LOWER PART)
A0
S-SYS AFT (auto) C-SYS
A1
TUNING FREQUANCY (HIGHER PART)
POS 15
A2
TUNING FREQUANCY (LOWER PART)
A3
S-SYS AFT (auto) C-SYS
A4
TUNING FREQUANCY (HIGHER PART)
POS 16
A5
TUNING FREQUANCY (LOWER PART)
A6
S-SYS AFT (auto) C-SYS
A7
TUNING FREQUANCY (HIGHER PART)
POS 17
A8
TUNING FREQUANCY (LOWER PART)
A9
S-SYS AFT (auto) C-SYS
AA
TUNING FREQUANCY (HIGHER PART)
POS 18
AB
TUNING FREQUANCY (LOWER PART)
AC
S-SYS AFT (auto) C-SYS
AD
TUNING FREQUANCY (HIGHER PART)
POS 19
AE
TUNING FREQUANCY (LOWER PART)
AF
S-SYS AFT (auto) C-SYS
B0
TUNING FREQUANCY (HIGHER PART)
POS 20
B1
TUNING FREQUANCY (LOWER PART)
B2
S-SYS AFT (auto) C-SYS
B3
TUNING FREQUANCY (HIGHER PART)
POS 21
B4
TUNING FREQUANCY (LOWER PART)
B5
S-SYS AFT (auto) C-SYS
B6
TUNING FREQUANCY (HIGHER PART)
POS 22
B7
TUNING FREQUANCY (LOWER PART)
B8
S-SYS AFT (auto) C-SYS
B9
TUNING FREQUANCY (HIGHER PART)
POS 23
BA
TUNING FREQUANCY (LOWER PART)
BB
S-SYS AFT (auto) C-SYS
BC
TUNING FREQUANCY (HIGHER PART)
POS 24
BD
TUNING FREQUANCY (LOWER PART)
BE
S-SYS AFT (auto) C-SYS
BF
TUNING FREQUANCY (HIGHER PART)
POS 25
MODEL MODEL
LETTER NO. LETTER NO.
MICON EEPROM EEPROM CHASSIS CTV FINAL
LAST INITIAL
SETTING DATA
DEFAULT RANGE
WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
REMARK
ADDRESS
DATA
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
40
SHARPNESS-OFFSET (SECAM)
04 00-0F
41
SHARPNESS-OFFSET (N358)
0C 00-0F
42
SHARPNESS-OFFSET (N443)
08 00-0F
43
44
FCO ACL OSO EHT EVG FFI AVL BKS
00-FF
45
SECAM N443 N358
PB-SECAM
BG I DK M
00-FF
46
SM1 SM0 FMWS AV BTSC HTL VMC VMI
00-FF
47
HP2 FSL RUS FRA CHN MLY ARB THA
00-FF
48
AGC1 AGC0 BIL CPTFOB-AV FOA-AV FOB-FE FOA-FE
NDF MSA LED-F
00-FF
00-03
49
4A
4B
4C
VOLUME
01 00-3C
4D
CONTRAST
3C 00-3C
4E
COLOUR
1E 00-3C
4F
BRIGHTNESS
1E 00-3C
50
TINT
1E 00-3C
51
SHARPNESS
1E 00-3C
52
53
54
55
POSITION/AV1/AV2
01 00-FF
56
FAV-POS A
0A 00-FF
57
FAV-POS B
14 00-FF
58
FAV-POS C
1E 00-FF
59
FAV-POS D
28 00-FF
5A
5B
5C
LAST POWER MODE
00 00-01
5D
WHITE-TEMP
00 00-02
5E
BLUE BACK
00 00-01
5F
LANGUAGE
00 00-07
60
LAST DIGIT MODE (1 OR 2)
00 00-01
61
62
SKIP 0 SKIP 1 SKIP 2 SKIP 3 SKIP 4 SKIP 5 SKIP 6 SKIP 7
80 00-FF
63
SKIP 8 SKIP 9 SKIP 10 SKIP 11 SKIP 12 SKIP 13 SKIP 14 SKIP 15
00 00-FF
64
SKIP 16 SKIP 17 SKIP 18 SKIP 19 SKIP 20 SKIP 21 SKIP 22 SKIP 23
00 00-FF
65
SKIP 24 SKIP 25 SKIP 26 SKIP 27 SKIP 28 SKIP 29 SKIP 30 SKIP 31
00 00-FF
66
SKIP 32 SKIP 33 SKIP 34 SKIP 35 SKIP 36 SKIP 37 SKIP 38 SKIP 39
00 00-FF
67
SKIP 40 SKIP 41 SKIP 42 SKIP 43 SKIP 44 SKIP 45 SKIP 46 SKIP 47
00 00-FF
68
SKIP 48 SKIP 49 SKIP 50 SKIP 51 SKIP 52 SKIP 53 SKIP 54 SKIP 55
00 00-FF
69
SKIP 56 SKIP 57 SKIP 58 SKIP 59 SKIP 60 SKIP 61 SKIP 62 SKIP 63
00 00-FF
6A
SKIP 64 SKIP 65 SKIP 66 SKIP 67 SKIP 68 SKIP 69 SKIP 70 SKIP 71
00 00-FF
6B
SKIP 72 SKIP 73 SKIP 74 SKIP 75 SKIP 76 SKIP 77 SKIP 78 SKIP 79
00 00-FF
6C
SKIP 80 SKIP 81 SKIP 82 SKIP 83 SKIP 84 SKIP 85 SKIP 86 SKIP 87
00 00-FF
6D
SKIP 88 SKIP 89 SKIP 90 SKIP 91 SKIP 92 SKIP 93 SKIP 94 SKIP 95
00 00-FF
6E
SKIP 96 SKIP 97 SKIP 98 SKIP 99
00 00-FF
6F
70
71
72
73
74
TUNING FREQUANCY (HIGHER PART)
S-SYS
POS 0
75
TUNING FREQUANCY (LOWER PART)
000:BG
76
S-SYS AFT (auto) C-SYS
001:I
77
TUNING FREQUANCY (HIGHER PART)
010:DK
POS 1
78
TUNING FREQUANCY (LOWER PART)
011:M
79
S-SYS AFT (auto) C-SYS
7A
TUNING FREQUANCY (HIGHER PART)
AFT
POS 2
7B
TUNING FREQUANCY (LOWER PART)
0:OFF
7C
S-SYS AFT (auto) C-SYS
1:ON
7D
TUNING FREQUANCY (HIGHER PART)
POS 3
7E
TUNING FREQUANCY (LOWER PART)
7F
S-SYS AFT (auto) C-SYS
MODEL MODEL
LETTER NO. LETTER NO.
1B
DE
53
3E
C4
00
MICON EEPROM EEPROM CHASSIS CTV FINAL
LAST INITIAL
SETTING DATA
DEFAULT RANGE
WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
REMARK
(1) 20th August 2001:
Added 3 new items.
12-2
12
12-1
C14-RF60
ADDRESS
DATA
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
100
POS 46
101
TUNING FREQUANCY (HIGHER PART)
POS 47
102
TUNING FREQUANCY (LOWER PART)
103
S-SYS AFT (auto) C-SYS
S-SYS AFT (auto) C-SYS
104
TUNING FREQUANCY (HIGHER PART)
POS 48
105
TUNING FREQUANCY (LOWER PART)
106
S-SYS AFT (auto) C-SYS
107
TUNING FREQUANCY (HIGHER PART)
POS 49
108
TUNING FREQUANCY (LOWER PART)
109
S-SYS AFT (auto) C-SYS
10A
TUNING FREQUANCY (HIGHER PART)
POS 50
10B
TUNING FREQUANCY (LOWER PART)
10C
S-SYS AFT (auto) C-SYS
10D
TUNING FREQUANCY (HIGHER PART)
POS 51
10E
TUNING FREQUANCY (LOWER PART)
10F
S-SYS AFT (auto) C-SYS
110
TUNING FREQUANCY (HIGHER PART)
POS 52
111
TUNING FREQUANCY (LOWER PART)
112
S-SYS AFT (auto) C-SYS
113
TUNING FREQUANCY (HIGHER PART)
POS 53
114
TUNING FREQUANCY (LOWER PART)
115
S-SYS AFT (auto) C-SYS
116
TUNING FREQUANCY (HIGHER PART)
POS 54
117
TUNING FREQUANCY (LOWER PART)
118
S-SYS AFT (auto) C-SYS
119
TUNING FREQUANCY (HIGHER PART)
POS 55
11A
TUNING FREQUANCY (LOWER PART)
11B
S-SYS AFT (auto) C-SYS
11C
TUNING FREQUANCY (HIGHER PART)
POS 56
11D
TUNING FREQUANCY (LOWER PART)
11E
S-SYS AFT (auto) C-SYS
11F
TUNING FREQUANCY (HIGHER PART)
POS 57
120
TUNING FREQUANCY (LOWER PART)
121
S-SYS AFT (auto) C-SYS
122
TUNING FREQUANCY (HIGHER PART)
POS 58
123
TUNING FREQUANCY (LOWER PART)
124
S-SYS AFT (auto) C-SYS
125
TUNING FREQUANCY (HIGHER PART)
POS 59
126
TUNING FREQUANCY (LOWER PART)
127
S-SYS AFT (auto) C-SYS
128
TUNING FREQUANCY (HIGHER PART)
POS 60
129
TUNING FREQUANCY (LOWER PART)
12A
S-SYS AFT (auto) C-SYS
12B
TUNING FREQUANCY (HIGHER PART)
POS 61
12C
TUNING FREQUANCY (LOWER PART)
12D
S-SYS AFT (auto) C-SYS
12E
TUNING FREQUANCY (HIGHER PART)
POS 62
12F
TUNING FREQUANCY (LOWER PART)
130
S-SYS AFT (auto) C-SYS
131
TUNING FREQUANCY (HIGHER PART)
POS 63
132
TUNING FREQUANCY (LOWER PART)
133
S-SYS AFT (auto) C-SYS
134
TUNING FREQUANCY (HIGHER PART)
POS 64
135
TUNING FREQUANCY (LOWER PART)
136
S-SYS AFT (auto) C-SYS
137
TUNING FREQUANCY (HIGHER PART)
POS 65
138
TUNING FREQUANCY (LOWER PART)
139
S-SYS AFT (auto) C-SYS
13A
TUNING FREQUANCY (HIGHER PART)
POS 66
13B
TUNING FREQUANCY (LOWER PART)
13C
S-SYS AFT (auto) C-SYS
13D
TUNING FREQUANCY (HIGHER PART)
POS 67
13E
TUNING FREQUANCY (LOWER PART)
13F
S-SYS AFT (auto) C-SYS
MODEL MODEL
LETTER NO. LETTER NO.
MICON EEPROM EEPROM CHASSIS CTV FINAL
LAST INITIAL
SETTING DATA
DEFAULT RANGE
WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
REMARK
ADDRESS
DATA
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
C0
TUNING FREQUANCY (LOWER PART)
POS 25
C1
S-SYS AFT (auto) C-SYS
C2
TUNING FREQUANCY (HIGHER PART)
POS 26
C3
TUNING FREQUANCY (LOWER PART)
C4
S-SYS AFT (auto) C-SYS
C5
TUNING FREQUANCY (HIGHER PART)
POS 27
C6
TUNING FREQUANCY (LOWER PART)
C7
S-SYS AFT (auto) C-SYS
C8
TUNING FREQUANCY (HIGHER PART)
POS 28
C9
TUNING FREQUANCY (LOWER PART)
CA
S-SYS AFT (auto) C-SYS
CB
TUNING FREQUANCY (HIGHER PART)
POS 29
CC
TUNING FREQUANCY (LOWER PART)
CD
S-SYS AFT (auto) C-SYS
CE
TUNING FREQUANCY (HIGHER PART)
POS 30
CF
TUNING FREQUANCY (LOWER PART)
D0
S-SYS AFT (auto) C-SYS
D1
TUNING FREQUANCY (HIGHER PART)
POS 31
D2
TUNING FREQUANCY (LOWER PART)
D3
S-SYS AFT (auto) C-SYS
D4
TUNING FREQUANCY (HIGHER PART)
POS 32
D5
TUNING FREQUANCY (LOWER PART)
D6
S-SYS AFT (auto) C-SYS
D7
TUNING FREQUANCY (HIGHER PART)
POS 33
D8
TUNING FREQUANCY (LOWER PART)
D9
S-SYS AFT (auto) C-SYS
DA
TUNING FREQUANCY (HIGHER PART)
POS 34
DB
TUNING FREQUANCY (LOWER PART)
DC
S-SYS AFT (auto) C-SYS
DD
TUNING FREQUANCY (HIGHER PART)
POS 35
DE
TUNING FREQUANCY (LOWER PART)
DF
S-SYS AFT (auto) C-SYS
E0
TUNING FREQUANCY (HIGHER PART)
POS 36
E1
TUNING FREQUANCY (LOWER PART)
E2
S-SYS AFT (auto) C-SYS
E3
TUNING FREQUANCY (HIGHER PART)
POS 37
E4
TUNING FREQUANCY (LOWER PART)
E5
S-SYS AFT (auto) C-SYS
E6
TUNING FREQUANCY (HIGHER PART)
POS 38
E7
TUNING FREQUANCY (LOWER PART)
E8
S-SYS AFT (auto) C-SYS
E9
TUNING FREQUANCY (HIGHER PART)
POS 39
EA
TUNING FREQUANCY (LOWER PART)
EB
S-SYS AFT (auto) C-SYS
EC
TUNING FREQUANCY (HIGHER PART)
POS 40
ED
TUNING FREQUANCY (LOWER PART)
EE
S-SYS AFT (auto) C-SYS
EF
TUNING FREQUANCY (HIGHER PART)
POS 41
F0
TUNING FREQUANCY (LOWER PART)
F1
S-SYS AFT (auto) C-SYS
F2
TUNING FREQUANCY (HIGHER PART)
POS 42
F3
TUNING FREQUANCY (LOWER PART)
F4
S-SYS AFT (auto) C-SYS
F5
TUNING FREQUANCY (HIGHER PART)
POS 43
F6
TUNING FREQUANCY (LOWER PART)
F7
S-SYS AFT (auto) C-SYS
F8
TUNING FREQUANCY (HIGHER PART)
POS 44
F9
TUNING FREQUANCY (LOWER PART)
FA
S-SYS AFT (auto) C-SYS
FB
TUNING FREQUANCY (HIGHER PART)
POS 45
FC
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
FD
S-SYS AFT (auto) C-SYS
FE
POS 46
FF
MODEL MODEL
LETTER NO. LETTER NO.
MICON EEPROM EEPROM CHASSIS CTV FINAL
LAST INITIAL
SETTING DATA
DEFAULT RANGE
WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
REMARK
13-2
13-1
13
C14-RF60
ADDRESS
DATA
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
180
POS 89
181
182
TUNING FREQUANCY (HIGHER PART)
POS 90
183
TUNING FREQUANCY (LOWER PART)
184
S-SYS AFT (auto) C-SYS
185
TUNING FREQUANCY (HIGHER PART)
POS 91
186
TUNING FREQUANCY (LOWER PART)
187
S-SYS AFT (auto) C-SYS
188
TUNING FREQUANCY (HIGHER PART)
POS 92
189
TUNING FREQUANCY (LOWER PART)
18A
S-SYS AFT (auto) C-SYS
18B
TUNING FREQUANCY (HIGHER PART)
POS 93
18C
TUNING FREQUANCY (LOWER PART)
18D
S-SYS AFT (auto) C-SYS
18E
TUNING FREQUANCY (HIGHER PART)
POS 94
18F
TUNING FREQUANCY (LOWER PART)
190
S-SYS AFT (auto) C-SYS
191
TUNING FREQUANCY (HIGHER PART)
POS 95
192
TUNING FREQUANCY (LOWER PART)
193
S-SYS AFT (auto) C-SYS
194
TUNING FREQUANCY (HIGHER PART)
POS 96
195
TUNING FREQUANCY (LOWER PART)
196
S-SYS AFT (auto) C-SYS
197
TUNING FREQUANCY (HIGHER PART)
POS 97
198
TUNING FREQUANCY (LOWER PART)
199
S-SYS AFT (auto) C-SYS
19A
TUNING FREQUANCY (HIGHER PART)
POS 98
19B
TUNING FREQUANCY (LOWER PART)
19C
S-SYS AFT (auto) C-SYS
19D
TUNING FREQUANCY (HIGHER PART)
POS 99
19E
TUNING FREQUANCY (LOWER PART)
19F
S-SYS AFT (auto) C-SYS
1A0
AV1
1A1
1A2
(auto) C-SYS
1A3
AV2
1A4
1A5
(auto) C-SYS
1A6
1A7
1A8
1A9
1AA
1AB
1AC
1AD
1AE
1AF
1B0
1B1
1B2
1B3
1B4
1B5
1B6
1B7
1B8
1B9
1BA
1BB
1BC
1BD
1BE
1BF
MODEL MODEL
LETTER NO. LETTER NO.
TUNING FREQUANCY (LOWER PART)
S-SYS AFT (auto) C-SYS
MICON EEPROM EEPROM CHASSIS CTV FINAL
LAST INITIAL
SETTING DATA
DEFAULT RANGE
WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
REMARK
ADDRESS
DATA
(HEX) D7 D6 D5 D4 D3 D2 D1 D0
140
TUNING FREQUANCY (HIGHER PART)
POS 68
141
TUNING FREQUANCY (LOWER PART)
142
S-SYS AFT (auto) C-SYS
143
TUNING FREQUANCY (HIGHER PART)
POS 69
144
TUNING FREQUANCY (LOWER PART)
145
S-SYS AFT (auto) C-SYS
146
TUNING FREQUANCY (HIGHER PART)
POS 70
147
TUNING FREQUANCY (LOWER PART)
148
S-SYS AFT (auto) C-SYS
149
TUNING FREQUANCY (HIGHER PART)
POS 71
14A
TUNING FREQUANCY (LOWER PART)
14B
S-SYS AFT (auto) C-SYS
14C
TUNING FREQUANCY (HIGHER PART)
POS 72
14D
TUNING FREQUANCY (LOWER PART)
14E
S-SYS AFT (auto) C-SYS
14F
TUNING FREQUANCY (HIGHER PART)
POS 73
150
TUNING FREQUANCY (LOWER PART)
151
S-SYS AFT (auto) C-SYS
152
TUNING FREQUANCY (HIGHER PART)
POS 74
153
TUNING FREQUANCY (LOWER PART)
154
S-SYS AFT (auto) C-SYS
155
TUNING FREQUANCY (HIGHER PART)
POS 75
156
TUNING FREQUANCY (LOWER PART)
157
S-SYS AFT (auto) C-SYS
158
TUNING FREQUANCY (HIGHER PART)
POS 76
159
TUNING FREQUANCY (LOWER PART)
15A
S-SYS AFT (auto) C-SYS
15B
TUNING FREQUANCY (HIGHER PART)
POS 77
15C
TUNING FREQUANCY (LOWER PART)
15D
S-SYS AFT (auto) C-SYS
15E
TUNING FREQUANCY (HIGHER PART)
POS 78
15F
TUNING FREQUANCY (LOWER PART)
160
S-SYS AFT (auto) C-SYS
161
TUNING FREQUANCY (HIGHER PART)
POS 79
162
TUNING FREQUANCY (LOWER PART)
163
S-SYS AFT (auto) C-SYS
164
TUNING FREQUANCY (HIGHER PART)
POS 80
165
TUNING FREQUANCY (LOWER PART)
166
S-SYS AFT (auto) C-SYS
167
TUNING FREQUANCY (HIGHER PART)
POS 81
168
TUNING FREQUANCY (LOWER PART)
169
S-SYS AFT (auto) C-SYS
16A
TUNING FREQUANCY (HIGHER PART)
POS 82
16B
TUNING FREQUANCY (LOWER PART)
16C
S-SYS AFT (auto) C-SYS
16D
TUNING FREQUANCY (HIGHER PART)
POS 83
16E
TUNING FREQUANCY (LOWER PART)
16F
S-SYS AFT (auto) C-SYS
170
TUNING FREQUANCY (HIGHER PART)
POS 84
171
TUNING FREQUANCY (LOWER PART)
172
S-SYS AFT (auto) C-SYS
173
TUNING FREQUANCY (HIGHER PART)
POS 85
174
TUNING FREQUANCY (LOWER PART)
175
S-SYS AFT (auto) C-SYS
176
TUNING FREQUANCY (HIGHER PART)
POS 86
177
TUNING FREQUANCY (LOWER PART)
178
S-SYS AFT (auto) C-SYS
179
TUNING FREQUANCY (HIGHER PART)
POS 87
17A
TUNING FREQUANCY (LOWER PART)
17B
S-SYS AFT (auto) C-SYS
17C
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (HIGHER PART)
POS 88
17D
TUNING FREQUANCY (LOWER PART)
17E
S-SYS AFT (auto) C-SYS
17F
POS 89
MODEL MODEL
LETTER NO. LETTER NO.
MICON EEPROM EEPROM CHASSIS CTV FINAL
LAST INITIAL
SETTING DATA
DEFAULT RANGE
WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE
REMARK
14-2
14-1
14
Loading...