Your new HITACHI COLOR TV incorporates a host of features designed to give you
excellent performance if you follow the instructions in this manual. Please read the
following instructions and "IMPORTANT SAFEGUARDS" notice before turning on your
TV for the first time.
Save these instructions for later use.
This television receiver will display television closed captioning ( or ), in
accordance with paragraph 15.119 of the FCC rules.
TABLE OF CONTENTS
TABLE OF CONTENTS............................................................................................................................1
IMPORTANT SAFEGUARDS ..................................................................................................................2
POWER SOURCE................................................................................................................................3
HOOK-UP CABLES AND CONNECTORS.............................................................................................8
BEFORE OPERATING YOUR TV SET...................................................................................................9
HITACHI SERVICE HOTLINE ..............................................................................................................39
IMPORTANT SAFEGUARDS
Follow all warnings and instructions marked on this television receiver.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS TELEVISION
SYSTEM TO RAIN OR MOISTURE.
NOTE: There are no user serviceable parts inside the receiver.
Model number and serial number are indicated on the back side of the
set.
2
IMPORTANT SAFEGUARDS
POWER SOURCE
This Hitachi color TV is designed to operate on 120 volts 60 Hz, AC household current.
Insert power cord plug into a 120 volt 60 Hz outlet.
NEVER CONNECT THE TV TO 50 Hz, DIRECT CURRENT, OR ANYTHING OTHER
THAN THE SPECIFIED VOLTAGE.
CAUTION:
POWER SUPPLY CORD
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
POLARIZED PLUG
NOTE: Never remove the back cover of the set as this can expose you to very high
voltages and other hazards. If the set does not operate properly, unplug the set and call
your dealer or service shop.
HITACHI
SAFETY POINTS YOU SHOULD KNOW ABOUT
YOUR HITACHI TELEVISION RECEIVER
CAUTION:
* Read all of these instructions.
* Save these instructions for later use.
* Follow all warnings and instructions marked on the television receiver.
Our reputation has been built on the quality, performance, and ease of service of HITACHI
television receivers.
Safety is also foremost in our minds in the design of these units. To help you operate these
products properly, this section illustrates safety tips which will be of benefit to you. Please
read it carefully and apply the knowledge you Obtain from it to the proper operation of your
HITACHI television receiver.
Please fill out your warranty card at once and mail it to HITACHI. This will enable HITACHI
to notify you promptly in the improbable event that a safety problem should be discovered
in your model of product.
FOR YOUR PERSONAL SAFETY
3
IMPORTANT SAFEGUARDS
1 This television set is equipped with a polarized alternating-current line plug (a plug
having one blade wider than the other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
2 When the power cord or plug is damaged or frayed, unplug this television set from the
wall outlet and refer servicing to qualified service personnel.
3 Do not overload wall outlets and extension cords as this can result in fire or electric
shock.
4 Do not allow anything to rest on or roll over the power cord, and do not place the TV
where the
power cord is subject to traffic or abuse. This may result in a shock or fire hazard.
5 Do not attempt to service this television set yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to qualified
service personnel.
6 Never push objects of any kind into this television set through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the television set.
7 If the television set has been dropped or the cabinet has been damaged, unplug this
television set from the wall outlet and refer servicing to qualified service personnel.
8 If liquid has been spilled into this television set, unplug it from the wall outlet and refer
service to qualified service personnel.
4
IMPORTANT SAFEGUARDS
9 Do not subject your television set to impact of any kind. Be particularly careful not to
damage the picture tube surface.
10 Unplug this television set from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
11-1 Do not place this television set on an unstable cart, stand, or table. The television
set may fall, causing serious injury to a child or an adult, and serious damage to the
appliance. Use only with a cart or stand recommended by the manufacturer, or sold with
the television set. Wall or shelf mounting should follow the manufacturer's instructions,
and should use a mounting kit approved by the manufacturer.
11-2 An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart combination to
overturn.
PROTECTION AND LOCATION OF YOUR SET
12 Do not use this television set near water, for example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
• Never expose the set to rain or water. If the set has been exposed to rain or water,
unplug the set from the wall outlet and refer servicing personnel.
13 Choose a place where light (artificial or sunlight) does not shine directly on the
screen.
5
IMPORTANT SAFEGUARDS
14 Avoid dusty places, since accumulated dust inside the chassis may cause failure of
the set when high humidity persists.
15 The set has slots, or openings in the cabinet for ventilation purposes, to provide
reliable operation of the receiver, and to protect from overheating. These openings must
not be blocked or covered.
• Never cover the slots or openings with cloth or other material.
• Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc.
• Never place the set near or over a radiator or heat register.
• Never place the set in a "built-in" enclosure, unless proper ventilation provided.
PROTECTION AND LOCATION OF YOUR SET
16-1 If an outside antenna is connected to the television set, be sure the antenna
system is protected against voltage surges and built up static charges, Section 810 of
the National Electrical Code, NFPA No. 70-1975, provides information with respect to
proper grounding of the mast and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors, location of antenna discharge
unit, connection to grounding electrode, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
16-2 Note to CATV system installer: (Only for the television set with CATV reception)
This reminder is provided to call the CATV system installer's attention to Article 820-40
of the NEC that provides guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding system of the building, as
close to the point of cable entry as practical.
17 An outside antenna system should not be located in the vicinity of overhead power
lines or other electrical lights or power circuits, or where it can fall into such power lines
6
IMPORTANT SAFEGUARDS
or circuits. When installing an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them might be fatal.
18 For added protection for this television set during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage due to lightning and power-line
surges.
OPERATION OF YOUR SET
19 This television set should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply at your home,
consult your television dealer or local power company. For television sets designed to
operate from battery power, refer to the operating instructions.
20 If the television set does not operate normally by following the operating instructions,
unplug this set television set from the wall outlet and refer servicing to qualified service
personnel. Adjust only those controls that are covered in the operating instructions as
improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the television set to normal operation.
21 When going on a holiday: If your television set is to remain unused for a period of
time, turn the television set "off" and unplug it from the wall outlet.
IF THIS SET DOES NOT OPERATE PROPERLY
22 If you are unable to restore normal operation by following the detailed procedure in
your operating instructions, do not attempt any further adjustment. Unplug the set and
7
HOOK-UP CABLES AND CONNECTORS
call your dealer or service technician.
23 Whenever the television set is damaged or fails, or a distinct change in performance
indicates a need for service, unplug the set and have it checked by a professional
service technician.
24 It is normal for some TV sets to make occasional snapping or popping sounds,
particularly when being turned on or off. If the snapping or popping is continuous or
frequent, unplug the set and consult your dealer or service technician.
FOR SERVICING AND MODIFICATION
25 Do not use attachments not recommended by the television set manufacturer as
they may cause hazards.
26 When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer that have the same characteristics as
the original part. Unauthorized substitutions may result in fire, electric shock, or other
hazards.
27 Upon completion of any service or repairs to the television set, ask the service
technician to perform routine safety checks to determine that the television is in safe
operating condition.
HOOK-UP CABLES AND CONNECTORS
Most video/audio connections between components can be made with shielded video
and audio cables that have phono connectors. For best performance, video cables
should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores
that sell audio/video products. Below are illustrations and names of common
connectors.
Before purchasing any cables, be sure of the output and input connector types required
by the various components. Also make sure the cables are the correct length.
8
BEFORE OPERATING YOUR TV SET
300-Ohm Twin Lead Connector "F" Type 75-Ohm Coaxial Antenna
Connector
This outdoor antenna cable must be For connecting RF signals (antenna or
cable
connected to an antenna adaptor TV) to the antenna jack on the television.
(300-Ohm to 75-Ohm).
Phono Connector S-Video (Super Video) Connector
Used on all standard video and audio This connector is used on camcorders,
VCRs,
cables which connect to inputs and outputs and laser disc players with an S-Video
feature
located on the Television's front and rear in place of the standard video cable to
produce
jack panels. a high-quality picture.
BEFORE OPERATING YOUR TV SET
INSTALLATION
ANTENNA
Unless your TV is connected to a cable TV system or to a centralized antenna system,
a good outdoor color TV antenna is recommended for the best performance. However,
if you are located in an exceptionally good signal area that is free from interference, and
multiple image ghosts, an indoor antenna may be sufficient.
LOCATION
Select an area where sunlight or bright indoor illumination will not fall directly on the
picture screen. Also, be sure that the location selected allows free flow of air to and from
the perforated back cover of the set.
9
ANTENNA CONNECTIONS
To prevent damaging the TV, do not leave the set in a place where the temperature
becomes too hot. For example, exposed to direct sunlight or near a heating device, etc.
VIEWING
This TV set may be viewed from any desired distance. Most viewers prefer a distance of
three to six feet or more, depending on screen size, for maximum eye comfort.
ANTENNA CONNECTIONS
Your 35TX69K is equipped with one VHF/UHF antenna terminal. The VHF/UHF
terminal can be used for normal TV, cable TV (CATV), or TV game, etc.
1. VHF (75) antenna/CATV
When using a 75-Ohm coaxial cable system, disconnect the VHF adapter from the 75
ohm receptacle and connect the outdoor antenna or CATV cable to a VHF 75 ohm
receptacle
2. VHF (300) antenna/UHF antenna
When using a 300-Ohm twin lead from an outdoor antenna, disconnect the (VHF or
UHF) indoor antenna leads from screws of the (VHF or UHF) adapter, and connect
outdoor (VHF or UHF) antenna leads to these screws of a (VHF or UHF) adapter.
3. When both VHF and UHF antennas are connected
Attach an optional ANT. MIXER to the TV antenna terminal, and connect the cables to
the ANT. MIXER.
10
LOCATION OF CONTROLS
Notes:
1. If an outdoor antenna/CATV is to be used, disconnect the indoor antenna. Do not leave
both the indoor and outdoor antennas/CATV connected at the same time, since ghosting
and poor reception may result.
2. Consult your dealer or service store for the ANT. MIXER and (VHF or UHF) adaptor.
3. The special converter (decoder) will be supplied by the cable company.
LOCATION OF CONTROLS
VCR STORAGE COMPARTMENT
This TV is equipped with a VCR storage compartment. Follow instructions below for
door operation and VCR installation.
VCR Storage Compartment illustration
TO CLOSE DOOR
Gently pull door to full forward horizontal position. Lower door to vertical position and
gently press lower right corner of door to engage magnetic latch.
FRONT PANEL CONTROLS
Click to see Front Panel Diagram.
Details are described by the number attached to the part name (example: ).
AVX (Audio/Video) selector
Press this button to select the current antenna source, or video: 1, 2, or 3. Your
selection is shown in the top right corner of the screen.
11
FRONT PANEL JACKS AND CONNECTIONS
VOLUME level
Press these buttons for your desired sound level. The volume level will be displayed on
the TV screen.
CHANNEL selector
Press these buttons until the desired channel appears in the top right corner of the TV
screen.
POWER button
Press this button to turn the TV on or off.
AI (Artificial Intelligence) sensor
This "Artificial Intelligence" sensor will make automatic picture adjustments depending
on the amount of light in the room to give the best picture. See page 30.
REMOTE CONTROL sensor
Point your Genius Remote at this area when selecting channels, adjusting volume, etc.
FRONT INPUT JACKS (for VIDEO:3)
Use these audio/video jacks for a "quick" hook-up from a camcorder or VCR to instantly
view your favorite show or new recording. (Press the AVX button until VIDEO:3 appears
in the top right corner of the TV screen.)
NOTE: Your Hitachi TV will appear to be turned "off" if there is no video input when VIDEO:
1, 2 or 3 is selected using the remote control AVX button. Press AVX until it returns to the
same video, if not the TV set is "off".
FRONT PANEL JACKS AND CONNECTIONS
• The front panel jacks are provided as a convenience to allow you to easily connect a
camcorder or VCR as shown in tn the following examples.
Front panel jacks and connections illustration
NOTE:
• Completely insert the connection cord plugs when connecting to front panel jacks. If you
do not, the played back picture may appear abnormal.
REAR PANEL JACKS
12
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.