Hitachi 42PD7800, 32PD7800 User Manual

Page 1

ENGLISH

USER'S MANUAL

Thank you very much for purchasing the HITACHI Plasma Display. Before using your monitor, please carefully read the "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" so you will know how to operate the monitor properly. Keep this manual in a safe place. You will find it useful in the future.

Notes on lnstallation Work:

This product is marketed assuming that it is installed by qualifed personnel with enough skill and competence. Always have an installation specialist or your dealer install and set up the product. HITACHI cannot assume liabilities for damage caused by mistake in installation or mounting, misuse, modification or a natural disaster.

Note for Dealers:

After installation, be sure to deliver this manual to the customer and explain to the customer how to handle the product.

32PD7800 42PD7800

Page 2

Important

Please read this User's Manual thoroughly, especially the Safety Instructions on Page 4 to 7. Mis-use may cause damage to your plasma monitor, which could shorten its lifespan, or cause injury to yourself. Should you encounter any difficulty in the set-up or operation of your monitor, firstly refer to the Troubleshooting guide at the rear of this manual. In the unlikely event of a problem occurring with your plasma monitor, switch off at the mains sockets, pull out the plugs, and contact your dealer immediately.

CAUTION

Under no circumstances remove the rear cover of your plasma monitor. Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!

Software Notice

It is prohibited for the end user of this product to copy, reverse engineer or reverse compile the software included therein, save to the extent permitted by law.

Plasma Monitor

After the plasma monitor has been on for any length of time, you will notice that the screen becomes warm. Please note that this is normal. Sometimes the screen might have some tiny bright or dark spots. Please note that this is normal.

CAUTION

To prevent scratches or damages to the plasma screen, do not knock or rub the surface with sharp or hard objects. Clean the screen with a soft cloth moistened with warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty. Do not use harsh or abrasive cleaners!

CAUTION

Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neutral detergent in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth. Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially because they would cause discoloration, scratches or cracks.

FEATURES

Large-screen, high-definition plasma display panel

The 42-inch color plasma display panel, with a resolution of 1024 (H) x 1024(V) pixels, the 37-inch color plasma display panel with a resolution of 1024(H) x 1024(V) pixels, and the 32-inch color plasma display panel with a resolution of 852(H) X 1024(V) pixels, creates a high-definition, large-screen (aspect ratio : 16:9) and low-profile flat display. Free from electromagnetic interferences from geomagnetic sources and ambient power lines, the panel produces high-quality display images free from color misconvergence and display distortion.

High Performance Digital Processor

A wide range of input signals can be handed, including composite, component, and HDMI. High Definition Digital Processor creates the fine-textured image with dynamic contrast. In addition, it corresponds to a broad array of personal computer signals, from 640 x 400 and 640 x 480 VGA to 1600 x 1200 UXGA. (Analog Input)

Easy-to-use remote control and on screen display system

The remote control included eases the work of setting display controls. Further, the on-screen display system, displays the status of signal reception and display control settings in an easy-to-view fashion.

Power saving system

The International ENERGY STAR® power saver feature saves power consumption automatically when input signals are not available. When connected to a VESA DPMS-compliant PC, the monitor cuts its power consumption while it is idle.

Connecting to an Audio Visual Device

• Two composite/S terminals*1, three composite terminals*2, two component terminals*2, a HDMI terminal and a photo input terminal (37/42 only) have been added. A composite video output terminal is also provided as a monitoring output.

A composite/S terminal = A side input

Two composite terminal and two component terminal are used at the same time. The component terminal would govern.

• A wide range of devices other than personal computers can also be connected.

• A RGB input is possible to switch to component signals from the Menu screen.

Power Swivel Feature (TV model only)

It allows to turn the plasma display left or right within ± 30 degree using the remote control.

Options (AV monitor model only)

Plasma monitor speaker

Page 3

ENGLISH

CONTENTS

FEATURES ..............................................................2

SAFETY INSTRUCTIONS ..............................4

IMAGE RETENTION OF PLASMA DISPLAY ..8

COMPONENT NAMES ..................................9

Main Unit ............................................................................9

Remote control ..................................................................10

Loading Batteries ............................................................10

Handling the Remote Control..........................................10

INSTALLATION INSTRUCTIONS ................13

Installation..........................................................................13

Anti-tumble measures........................................................13

Connecting to an Audio Visual Device..............................14

Connecting to a PC ..........................................................16

Mounting the Speaker Unit................................................17

Mounting the Side Input ..................................................19

Power Cord Connection ....................................................20

OPERATING INSTRUCTIONS......................21

Turning Power On and Off ................................................21

Input Switching..................................................................22

Size Switching ..................................................................22

Volume Adjustment............................................................24

Audio Mute ........................................................................24

Power Swivel ....................................................................25

Input Signal Screen Display..............................................26

Displaying MULTI PICTURE ..............................................27

Picture Freezing ................................................................29

Photo Input Display (37/42 only) ......................................30

Using the Menu Screen (On-screen display system) ......33

SETUP MENU (TV mode) ..................................................34

SETUP MENU (Video mode) ............................................36

SETUP MENU (RGB mode: RGB1 (DVI-PC),

RGB2 (RGB)) ..................................................................37

FUNCTION MENU ............................................................39

PICTURE MENU (TV/Video mode) ....................................40

PICTURE MENU (RGB mode) ..........................................43

AUDIO MENU....................................................................44

TIMER MENU ....................................................................45

LANGUAGE MENU ..........................................................45

Notes about This Manual

• The information in this manual is subject to change without notice.

• While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us should you have any comments, views or questions about our product.

• Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, in using the product. We are not held liable for damages caused by improper handling of the product.

• Reproduction of this manual in whole or in part without our prior written permission is prohibited.

• The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.

OTHER FUNCTIONS ..................................46

Automatic Store ................................................................46

Audio Switching ................................................................47

Power Save Mode ............................................................48

DVD Player/STB Selection ................................................48

Signal Check (RGB mode)................................................49

TROUBLESHOOTING ..................................50

Symptoms That Seemingly Appear to be Failures............50

Actions to Correct Abnormal Displays ..............................52

PRODUCT SPECIFICATIONS ......................53

Signal Input ......................................................................54

Recommended Signal List ................................................55

Page 4

SAFETY INSTRUCTIONS

About the Symbols

This Plasma monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions.

Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the user and others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the contents.

WARNING

CAUTION

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due to incorrect handling.

Typical Symbols

This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.

This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left indicates that disassembly is prohibited).

This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left indicates that the power plug should be disconnected from the power outlet).

Never use the monitor if a problem should occur.

Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock. In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be dangerous.

Do not insert liquids or foreign objects.

Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children are present. If liquids or foreign objects should enter the monitor, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer.

• Do not place the monitor in a bathroom.

• Do not expose the monitor to rain or moisture.

• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor.

• Do not place metals, combustibles, etc on or around the monitor.

Never disassemble or modify the monitor.

The monitor contains high voltage components. Modification could result in fire or electrical shock.

• Never remove any fixed cover.

Do not give the monitor any shock or impact.

If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock. If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer.

Do not place the monitor on an unstable surface.

If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.

• Do not place the monitor on an unstable, slant or vibrant surface such as a wobbly or inclined stand.

Do not obstruct the ventilation of the monitor.

If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in damage and shorten the lifespan of your monitor due to overheating. Make sure there is ample ventilation.

• Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls.

• Do not place anything around ventilation openings of the monitor.

• Never block ventilation openings.

• Do not put the plasma screen side up.

• Do not cover the monitor with a tablecloth, etc.

• Do not place the monitor on a carpet or bedding, or near a curtain.

Use only the correct power outlet.

Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication on the monitor and the safety standard.

• The enclosed power cord must be used depending on the power outlet to be used.

Disconnect the

plug from the power outlet.

Do not

disassemble.

Page 5

ENGLISH

WARNING

Be cautious of the power cord connection.

Incorrect connection of the power cord could result in fire or electrical shock.

• Do not touch the power cord with a wet hand.

• Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.

• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.

• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead, obtain an appropriate extension lead or consult your dealer.

• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value, type and approval as the original. Ensure the fuse cover is returned to its original position.

Be sure to keep safety ground connection.

Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the enclosed power cord. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.

Be careful in handling the power cord and external connection cables.

If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension to the power cord and cables. If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.

• Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.

• Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug or connector.

• Do not place the cord near the heater.

• Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.

• Do not touch the power plug when lightening is close to you.

• Avoid coiling the power cord and bending it sharply.

• Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where they exit from the apparatus.

• Do not modify the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.

• Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

• Do not allow the battery to be exposed to fire or water.

• Avoid fire or high-temperature environment.

• Do not hold the battery with metallic tweezers.

• Keep the battery in a dark, cool and dry place.

• Do not short circuit the battery.

• Do not recharge, disassemble or solder the battery.

• Do not physically impact the battery.

• Use only the battery specified in the manual of this monitor.

• Make sure the plus and minus terminals are correctly aligned when loading the battery.

• If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or clothes, rinse well with water.

• Obey the local laws on disposing the battery.

Surely connect

the ground wire.

SAFETY INSTRUCTIONS (continued)

About the Symbols (continued)

Page 6

CAUTION

PRECAUTIONS

Be careful in moving the monitor.

Neglect could result in an injury or damage.

• Do not move the monitor during use. Before moving, disconnect the power plug and all external connections.

• You are advised to move the monitor with two persons.

• Avoid any impact or shock to the monitor; particularly take care of glass screen.

Do not put anything on top of the monitor.

Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution in households where children are present.

Avoid a humid or dusty place.

Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.

• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.

Avoid a high temperature environment.

The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire.

• Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.

• Do not put the monitor in a place where the temperature is widely changing.

Remove the power cord for complete separation.

• For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time.

• Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.

Be careful in operating power swivel.

Placing hands or faces near the monitor while operating the swivel function could cause a physical injury or damage. Use special caution in households where children are present.

• Installation environment

Do not obstruct a ventilation hole. Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor.

Do not put the monitor in the following places.

• Hot places such as near heater, place exposed to the direct rays of the sun.

• A place where the temperature is widely changing.

• Places with soot, dust or high humidity.

• Poor air ventilation place.

• Place near fire.

• A wet place such as bathroom, or shower room.

• Place where you can trip over it.

• Always vibrating or strongly vibrating places.

• Distorted or unstable places.

• How to view the monitor

If you use the monitor in too dark a room, your eyes may become tired. Please use it in a reasonably bright room. Avoid direct rays of the sun to the screen in order to prevent eye fatigue. Your eyes will get fatigued after viewing the monitor for long period of time. Relax your eyes by viewing away from the monitor from time to time. Please watch the monitor in downward direction.

• Note on image retention

The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images. Tips to prevent such image retention are:

- Do not display images having sharp brightness differences or high-contrast images, such as monochrome characters and graphic patterns, for long.

- Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them using screen saver function.

- Turn down the contrast and brightness controls.

• How to clean the plasma screen panel of the monitor

Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet. To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or hard objects. Clean the screen with a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or abrasive cleaners.

• How to clean the cabinet of the monitor

Disconnect the

plug from the power outlet.

SAFETY INSTRUCTIONS (continued)

About the Symbols (continued)

Page 7

ENGLISH

• Prevention of an obstacle to Radio receivers

This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.

- Keep the monitor away from Radio.

- Adjust Radio antennas in order for the monitor not to receive interference.

- The antenna cable of Radio should be kept away from the monitor.

- Use a coaxial cable for antenna. You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor. If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.

• Precautions for the cable connection

- Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are properly made and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing connections.

- Confirm the connector is fixed tightly when the signal cable is connected. Also confirm the screws on the connector are tightened.

- Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc..

- Use a plug with ground terminal and make sure that it connects to the ground.

• Precaution during transportation

Please pay attention when you transport this monitor because it is heavy. Furthermore, use the original carton box and its packaging materials when the monitor is transported. Failure to transport the monitor in any carton except the original carton may result in damage to the monitor. Save the original carton box and all packing material.

Do not physically impact the remote control.

A physical impact could cause damage or malfunction of the remote control.

• Take care not to drop the remote control.

• Do not place heavy objects on the remote control.

Avoid strong rays.

Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.

Avoid radio interference.

Any interfering radiation could cause distorted images or noises.

• Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.

Set the sound volume at a suitable level.

It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.

• Precautions for the installation

- Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved stand or legs with the fixings provided according to the instructions.

- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

- This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet that could cause the product to overturn resulting in product damage and/or personal injury.

- Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.

- Only use the attachments/accessories specified by the manufacturer.

- Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.

• Other precautions

- Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or handicapped people.

- Disposal of this product may require specific instructions pertaining to your resident region.

- Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!

SAFETY INSTRUCTIONS (continued)

About the Symbols (continued)

Page 8

IMAGE RETENTION OF PLASMA DISPLAY

There are different characteristics that result in panel image retention depending on how the plasma display is used. Situations and effective usage methods related to ghosting are provided below.

Image retention characteristics of a plasma display

The image retention phenomenon of a plasma panel occurs due to partial phosphor degradation arising from partial character and figure display.

For example, when the character image as shown in Fig. A at the right is continuously displayed for a long period of time, the only part of the phosphor (Red,Green, Blue) that will degrade will be the color of the applicable character display portion. Consequently, when a white image is displayed on the entire screen as shown in Fig. a, the character marks displayed up to that time will become a color difference visible to the eye, but the phosphor will never burn.

■ The degree of image retention is proportional to the brightness of the characters and figures displayed as well as the display time.

• The tendency of the phosphor is to degrade more the brighter the characters and figures are displayed. When images of figures with different levels of brightness, as shown in Fig. B, are continuously displayed for a long period of time, it becomes easier for image marks at locations when the brighter figures are displayed to be noticeable.

* The image retention images in this document are exaggerated for the purpose of explanation. The actual manner in which the image retention

is seen differs depending on the operation time and brightness.

Methods to Reduce the Occurrence of Image Retention

• Lower the Contrast and Brightness settings of the plasma display as much as possible. A function is provided in the display that controls the brightness of the screen to reduce degradation of the panel. Using this function makes it possible to reduce image retention. (Refer to Panel Life (Extend 1.or Extend 2) shown on )

• Set the plasma monitor to an “Screen Wipe” or “Luminance Manager” display. The occurrence of image retention when displaying images of identical patterns, such as static images, for long periods of time can be reduced by displaying a completely white screen for about 1 ~ 2 hours after terminating the display. Luminance Manager function works to reduce image retention when displaying images on the four corners, such as TV station logos and clock display. (Settings can be made using Screen Wipe and Luminance Manager from Function MENU shown on )

• Using in combination with moving images Since the degradation of the fluorescent material progresses comparatively uniform for moving images, the occurrence of partial image retention can be controlled. We recommend to use in combination with moving images such as a DVD. * Please be careful since image retention will occur if display is left in a two screen display state for a long period of time. * Television broadcasts include images displayed for long periods of time in which the left and right or top and bottom of the image are cut

and broadcast station name or time are displayed for a long period of time at the same portion of the screen. Image retention in these portions can be expected to occur, so please be aware.

[Fig. A]

[Fig. B]

[Fig. a]

[Fig. b]

Notes

About screen defects

• High precision technology is used in the making of plasma panels but there may be dark spots (points that do not illuminate) and bright

spots (points that are too bright) in some cases. These do not indicate a malfunction.

About residual images

• In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will

disappear and return to normalcy. This is not a malfunction.

About the panel screen

• Plasma displays display images by means of electrical discharges inside the panel. Because of this, the temperature of the panel surface

may rise in some cases.Also, plasma displays are made of finely processed glass. A reinforced glass filter is installed over the panel surface but avoid strong impact because there is still danger of glass breakage.

About the power swivel

• Do not put hands or faces close to the monitor while operating the swivel function. It could cause a physical injury. Use special caution in

households where children are present. (Refer to Power Swivel shown on )

Page 9

ENGLISH

COMPONENT NAMES

Main Unit

Control panel

• Adjustment buttons are located on the bottom.

• The back cover is provided with indications to distinguish the adjustment buttons.

MENU button

SUB-POWER button

VOLUME UP/DOWN buttons ( ADJUST buttons)

INPUT SELECT button

(OK button)

CHANNEL UP/DOWN buttons (SELECT button)

• ( ) indicates the function while the MENU is displayed on the screen.





Remote-control receiver

Indicating lamp

• The main power switch is located at the back, on the lower surface.

Main power switch

Caution when moving the main unit

• As this product is heavy, whenever it is moved, two people are required to transport it safely.

• Whenever the unit is moved it should be lifted forwards using the two handgrips at the back, and the unit should then be held at the base on both sides for stability.

Handgrips

Rear

Handgrips

External speaker terminals

Handgrips

External speaker terminals

16 16

External device connection terminals

RGB input terminals

Panel

Cabinet (front frame)

Front

AV monitor

(32)

(42)

(37)

Page 10

Remote control

POWER ON/OFF button

INPUT SELECT buttons

MENU button

OK button

SOUND MODE button

VOLUME UP/DOWN button

PROGRAM SELECT buttons

(TV)

MULTI MODE button

RECALL button

FUNCTION SELECT button

DVD CONTROL button

FREEZE/RETURN buttons

SELECT/ADJUST button

PICTURE MODE button CH I/CH II button (TV) CHANNEL UP/DOWN button (TV) MUTE button

MULTI PICTURE button

PHOTO INPUT buttons

SWIVEL button

T/TEXT button

(TV)

Loading Batteries

1. Open the battery cover.

• Slide back and remove the battery cover in the direction of the arrow.

2. Load batteries.

• Load two Size AA batteries included observing the correct polarities.

3. Close the battery cover.

• Replace the battery cover in the direction of the arrow and snap it back into place.

Handling the Remote Control

Use the remote control within about 5 m from front of the unit’s remote-control sensor and within 30 degrees on both sides.

• Do not use new and old batteries together. The batteries could explode or leak, resulting in fires, physical injury, or stains.

• When loading batteries, observe their correct polarities as marked on the product. If loaded in the wrong direction, the batteries could explode or leak, resulting in fires, physical injury, or stains.

ATTENTION

• Do not drop or impact the remote control.

• Do not splash the remote control with water or put it on a wet

object to avoid possible failures.

• Before leaving the remote control out of use for an extended period of time, remove the batteries from it.

• If the remote control begins to lack responsiveness, replace the batteries.

• Strong light such as direct sunlight impinging on the photoreceptor of the remote control can cause operational failure. Position this unit to avoid direct contact with such light.

COMPONENT NAMES (continued)

@@@@@@@@e? @@@@@@@@e? @@h? @@h? @@h? @@h? @@h? @@h?

@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e @@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e

@@@@@@@@ @@@@@@@@

@@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

?@@ ?@@ ?@@ ?@@ ?@@

?@@ ?@@@@@@@@ ?@@@@@@@@

?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@ ?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@

@@g @@g @@g @@g @@g @@g @@@@@@@@ @@@@@@@@

@@ @@ @@ @@ @@ @@ @@ @@

CAUTION

With in 30 degrees

About 3m

With in 30 degrees

About 3m

About 5m

Page 11

ENGLISH

*1 FUNCTION SELECT button

This remote controls has functions to control DVD player, DVD recorder, and STB for certain makers, besides this set. Press button to operate those equipments. Each time pressed, LED lamps (TV, DVD, SAT) left to button lights to indicate the selection. For details, refer to

*2 LED

LED lamps of DVD and SAT have 2 conditions (lighting or blinking). Lighting: Indicate that the corresponding button becomes DVD (STB) mode.

Change to STB (TV) mode when press the button during LED lighting.

Blinking: Indicate that DVD or STB makers can be set up.

Set up makers/types for DVD or STB during LED blinking (30 sec). For details, refer to If press the button on the remote control after LED light is off, LED light becomes on the corresponding code.

Remote control (continued)

COMPONENT NAMES (continued)

DVD and SAT

INPUT SELECT

Press this button to change input mode.

SOUND MODE

You may recall the sound mode by pressing this button. Each time pressed, sound mode is changed in following sequence.

Movie Music

Favorite Speech

CH I/II

This button is for A2 / NICAM models only.

FUNCTION SELECT

Press this button to indicate function mode with a lamp.

RECALL (TV)

With this button, the display change between “--”,“---”,“-” and AV00 on the top right hand corner of the screen. “--” is for 2 digit channel selection, “---” is for 3 digit channel selection and “-” is

for 1 digit channel selection.

RECALL (Video/RGB)

Press this button to display input signal.

DVD CONTROL

You can use these buttons to operate the selected brand of DVD player.

FREEZE/RETURN

Press this button to change the picture to freeze mode. Press it again to return to normal picture.

PICTURE MODE

You may recall the picture mode by pressing this button. Each time pressed, picture mode is changed in following sequence.

Dynamic

Natural

Cinema

MUTE

PROGRAM SELECT

Press these buttons to select a TV program directly.

MULTI MODE

In multi-picture mode, pressing this button will change the multi-picture mode.

TIME (TV)

Pressing this button can indicate the time by On-Screen display when receiving a TV program on the screen including TELETEXT service with the time information.

Press this button to turn off the set sound. When press again or the volume up button, the audio will be restored.

MULTI PICTURE

Press this button to change the screen to multi-pictures. Press it again to return to normal picture.

PHOTO INPUT (37/42 only)

Press this button to display the pictures from digital camera and USB card reader.

SWIVEL

ZOOM

Press this button can change Picture size.

Press this button to rotate TV. Use cursor key ( ) to select the degree of rotation.

Page 12

TV / TEXT button

CANCEL button

INDEX button

TEXT / TV + TEXT button

PAGE UP / DOWN button

COLOR buttons (RED, GREEN, YELLOW, BLUE)

SUB TITLE button

REVEAL button

Buttons on Remote Control

This switches the receiver between the TV mode and the TELETEXT mode.

Function

In TELETEXT mode, this button switches between TV+TEXT screen (split) and TELETEXT only.

This selects the P100 (100 page).

Use this to access a subtitle service directly rather than through a TELETEXT service (subject to subtitle service broadcasting).

This allows the screen to return to the TV mode temporarily while searching for a required text page. When the required text page has been received, the page number will be displayed at the top left of the screen. Press the CANCEL button again to display the TELETEXT screen.

Each of these buttons selects a link page displayed at the lower part of the screen.

This allows hidden information (found on some teletext pages) to be displayed on the screen.

These buttons increase / decrease the TELETEXT page number.

TV / TEXT

TEXT / TV + TEXT

INDEX

SUB TITLE

CANCEL

RED

GREEN

YELLOW

BLUE

REVEAL

PAGE UP / DOWN

NOTE

• Certain pages do not show linked pages at the bottom of the screen. To display linked pages, press the INDEX button.

[Button for TELETEXT Mode]

TELETEXT FUNCTION

Remote control (continued)

COMPONENT NAMES (continued)

Page 13

• In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches : For a desktop set-up) or more between the sides and other objects such as walls, etc., so that the ventilation holes are not blocked.(*)

ENGLISH

INSTALLATION INSTRUCTIONS

Installation

Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can cause overturning or dropping and result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries or property damage caused by use of other mount units or improper installation.

Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.

Loosen a cord or chain enough while operating power swivel to avoid possible physical injury.

Anti-tumble measures

Securing to a wall or pillar

Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar.

Securing desktop

1) Using wood screws (two), fasten the set to the clamping screw holes on the rear of the stand as shown.

2) Using commercially available wood screws, secure the set firmly in position.

Read SAFETY INSTRUCTIONS ( to ) carefully to ensure maximum safety before proceeding to these steps:

• Choose an appropriate site and install the product on a level table where the stand is secure.

• Install the monitor to have ready access to a power socket available.

• Make sure that the power switch of this device is turned off.

4 7

WARNING

CAUTION

10cm or more*

Cord or chain

Wall or Pillar

Clamp

CAUTION

Hook

Clamp

Cord or chain

Wood screw

Two places

Cord or chain

Wall or Pillar

CAUTION

Page 14

Connecting to an Audio Visual Device

(1) Make sure that the power switch of the monitor is turned off. (2) Make sure that the power switch of the imaging device is turned off. (3) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this

device and the signal output terminal of the imaging device.

Side Input

To component

output terminals

To component

output terminals

To S video

output terminal

To composite

output terminals

To audio

output terminals

To audio output

terminals

To audio output

terminals

To composite

output terminal

To audio output

terminals

To S, composite

audio output

terminal

To USB output

terminal

Headphone

To composite

input terminals

To audio input

terminals

Set-Top Box

Antenna

VTR VTR

VTR

DVD Player

To component

input terminals

To component

input terminals

TV Type only

Photo input terminal (37/42 only)

• If a component input terminal and a composite input terminal of AV1 and AV2 connect to the monitor at the same time, component input would govern.

• If a video equipment with an S video output terminal is used, cabling by the S video cable is recommended to provide finer video quality. (If an S video input terminal and a video input terminal of AV3 or AV5 (side input) connect to the monitor at the same time, S video input would govern.)

• If the OUTPUT (Monitor) terminal is connected to an external monitor with a 75 Ohm terminal, it is possible to view the same image as on the main unit. But it is possible to monitor only the composite video signal from AV1 ~ AV5 input or the S video signal from AV3 and AV5 that is displayed on the screen at the time.

• The photo input function might not be provided, depending on a model.

• Secure connecting cables to the stand with the provided clamp.

HDMI*

• HDMI (High-Definition Multimedia Interface) is a digital interface based on DVI (Digital Visual Interface), which is an added function for audio visual equipment.

– It does not have degradation by transmission since it is digital. – With only one cable, it is possible to transmit both picture signals and audio signals.

• In case of using analog audio as connecting with DVI-HDMI transformation connector, use an analog audio terminal for AV1 input.

[An example of connecting audio visual devices]

INSTALLATION INSTRUCTIONS (continued)

Speaker (R)

Power cord

Monitor (rear panel)

Speaker (L)

Page 15

ENGLISH

When the "ANT" terminal is connected to outdoor antenna instead of CATV system, please note that a good antenna adaptor is necessary. See the diagram on the right.

Precautions when connecting the antenna

• Clamp section A using pliers when installing the coaxial cable. If other types of adaptors are used, be sure that the core and shielding are good.

• Please use a coaxial cable which is free from interference to connect the antenna. Avoid using a parallel flat feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on the screen.

• Avoid using indoor antenna as this may be affected by interference. Please use CATV net or outdoor antenna.

• Keep the power cord as far away from the antenna wire as possible.

• For safety, install an external antenna conforming to AS1417.1 (applicable for Australia only)

If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not provided) for RF LEADS to reduce the noise.

Connecting to an Audio Visual Device (continued)

INSTALLATION INSTRUCTIONS (continued)

Page 16

Connecting to a PC

(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this

device.

• See "Product Specifications" concerning the specifications of this device. 

(2) Make sure that the power switch of the personal computer is turned off. (3) Connect the signal input terminal (RGB 1 or RGB 2) on the rear panel of this device to the display signal output

terminal of the personal computer.

• Use a cable that fits the input terminal of this device and the output terminal of the personal computer.

• Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with

the personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the personal computer manufacturer or your local retail dealer.

53 57

(D-sub)(DVI)

Monitor (rear panel)

Speaker (R) Speaker (L)

Power cable connector

Powe r cord

To signal output terminal (DVI)

To audio output terminal

3.5mm Stereo mini jack

To signal output terminal (D-sub)

To signal output terminal (DVI)

(Example)

DVD Player

Connecting to a PC Device Connecting to an Audio Visual Device

• Setting RGB1: DVI-PC RGB2: RGB For details, refer to 

• Setting RGB1: DVI-STB RGB2: Component For details, refer to 

INSTALLATION INSTRUCTIONS (continued)

56 57

55 56

Page 17

ENGLISH

Mounting the Speaker Unit

INSTALLATION INSTRUCTIONS (continued)

Make sure that the main power swich of the monitor is turned off (standby or indicating lamp: off/red) when removing or connecting the speaker cables.

Make sure to use the speaker systems fastened with the speaker holders and the screws.

Mounting the Speaker System to the Monitor

1. Mounting the Speaker System to the Monitor

Hook the clamps (3 pieces) into the holes as shown in the figure, and pull them down. Follow the step in both Right and Left sides.

2. Attach the speaker holders

After twisting the screws off as shown, fasten the speaker system to the monitor with the speaker holder by the screws. The speaker holder direction is opposite on the Right and Left speaker systems.

3. Attach the speaker connecting cables to the monitor. (Make sure the ferrite core is toward the monitor side)

Right Side

Rear of the monitor

Clamps

Right Side

Rear of the monitor

Twist off the screws

Speaker holder

Monitor

Speaker System

Speaker holder

Screws x 4

NOTE

In case that the speaker systems do not fit with the monitor body’s height.

When loosen the screws fixing the aluminum pieces, the speaker system is movable up and down. Adjust the position to the monitor body’s height, then tighten up the screws.

Pull off while twisting

Please prepare the supplieol speaker cables

Treating the wire ends

Ferrite core Ferrite core

(R)

RedBlack

(L)

RedBlack

Connect the copper colored wire

Connect the silver colored wire

Connect the copper colored wire

Press down the lever

Raise the lever

Insert the wire

How to connect the speaker cables (Moniter side)

Place to attach the side input.

CAUTION

Aluminum pieces

Screwdriver

Page 18

Mounting the Speaker Unit (continued)

INSTALLATION INSTRUCTIONS (continued)

4. Attach the speaker cables to speaker systems.

Connect the copper - colored wire to the Red side.

Connect the silver - colored wire to the Black side.

Speaker terminals

Hold down the lever

Release the lever

Insert the wire

How to connect the speaker cables (Speaker side)

Make sure to secure the power cable and the connecting cables for other audio visual devices, except the speaker connecting cables, to the clamp of the monitor stand and the rear of it. When the monitor is swiveled, the connectors might be dropped out and generate heat. It could cause fire and/or connector failures.

CAUTION

Page 19

ENGLISH

Mounting the Side Input

INSTALLATION INSTRUCTIONS (continued)

• With the speaker unit

1. Mount the side input into the speaker holder.

Hook the clamps (4 pieces) of the speaker holder into the holes as shown in the figure and pull them down until it sounds click. Fasten the side input with the speaker holder by the screws. Refer to about the connection of side input. See the below figure how to treat the cable.

2. Mount the side input into the securing holder.

Fasten the side input with the speaker holder by the screws. See the below figure how to treat the cable.

• Without the speaker unit

1. Attach the holder for the side input.

Side input

Screw x 1

Speaker holder

Clamp (42, 37)Side input

32 inch

42 inch 37 inch

Screw hole Clamp (42, 37)

Clamp (32)

Screw x 2

Holder

Screw hole

Clamp (32)

Clamp (42, 37)

42 inch 37 inch

32 inch

Side input

Page 20

INSTALLATION INSTRUCTIONS (continued)

Connect the power cord, after completing all other connections. ...42, 32



Connect the power cord to this device.



Connect the power cord plug to the power outlet.

(The type of plug is different from this drawing for some countries.)

Power Cord Connection





• Use only the power cord provided. (Ask your local retail dealer about the power cord for AV monitor)

• Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.

Connect the power cord, after completing all other connections. ...37





CAUTION

Page 21

ENGLISH

OPERATING INSTRUCTIONS

Indicating lamp

Main power switch

(32)

(37)

(42)

SUB-POWER button

POWER ON/OFF

button

Turning Power On and Off

• To turn the monitor power ON, press the main power switch on the monitor main unit to ON, and then press the SUB POWER button of control panel or the power button on the remote control.

• To turn the monitor power OFF, press the SUB POWER button of control panel or the power button on the remote control, and then press the main power switch on the monitor main unit to OFF.

• During normal use, the main power switch is set in the ON position, and the monitor can then be turned ON/OFF using the SUB POWER button or the power button on the remote control.

Indicating lamp

Indicating

lamp

Power status Operating

Off Off

When the main power switch is set to OFF.

Lights red

Off

(standby)

When the main power switch is ON, and the power button on the remote control or the SUB POWER button on the underside of the front of the frame is OFF.

Lights green On

When the main power switch is ON, and the power button on the remote control or the SUB POWER button on the underside of the front of the frame is ON.

Lights orange

Off

(Power Save)

When the main power switch is ON, and the power button on the remote control or the SUB POWER button on the underside of the front of the frame is ON. However, the state in POWER SAVE mode

When the indicating lamp lights in orange or the message “No Sync. Signal”, “Power Save” or “Invalid Scan Freq.” appears on the screen, there is something unusual about the status of reception. See “Power Save Mode” or “Symptoms That Seemingly Appear to be Failures.”

48 49

ATTENTION

• Avoid repeatedly turning the monitor on and off at short time intervals. Failures might result from such operation.

• Turn off the main power switch before leaving the monitor out of

use for an extended period of time.

• If a power failure occurs while the main unit is running, it would

be powered on upon recovery from the failure. Turn off the unit main power switch before leaving the main unit.

Page 22

OPERATING INSTRUCTIONS (continued)

INPUT SELECT button

CHANNEL UP/DOWN buttons

Input Switching

Size Switching

• Input can be switched by pressing the AV1~6, RGB1 or RGB2 buttons of the remote control.

• Input can be switched to TV by pressing CHANNEL UP/DOWN buttons or PROGRAM SELECT buttons.

• Input can be switched in the sequence of TV

➝ AV1 ➝ AV2 ➝ AV3 ➝ AV4 ➝ AV5 ➝ AV6 ➝ RGB1 ➝ RGB2 by pressing the INPUT SELECT button of the control panel.

* TV display is not available in the AV monitor.

Each time the ZOOM button of the remote control is pressed, the screen display size will change in sequence and the status will be displayed at the bottom of the screen.

• During TV/VIDEO signal input (TV, AV1, AV2, AV3, AV4, AV5, AV6, RGB1 (set to [DVI-STB]) and RGB2 (set to [Component]))

* TV display is not available in the AV monitor.

• The size will fix as Full mode and not change when receiving the component signal of 1080i/50, 1080i/60 or 720p/60.

INPUT SELECT

buttons

RECALL button

ZOOM button

Display size selection diagram

When you want to

Set the display size to

Input signal Display screen Remarks

Play a 4:3 image in a 16:9 screen faithfully.

4 : 3

(4:3 signal)

Blanking occurs on both sides.

Play a 4:3 image in a 16:9 screen with the height and width of the middle of the screen enlarged on equal scales and with both sides appearing somewhat enlarged.

Panoramic

Play a 16:9 VISTA size image in the 4:3 image faithfully reproduced on the 16:9 screen.

Zoom

(Vista)

• The 4:3 image is called a letterbox image.

• In some cases, some slight blanking may

remain at the top and bottom.

Play a 21:9 Cinema size image in the 4:3 image expanded vertically on the 16:9 screen.

Cinema

(Cinema)

In some cases, some slight blanking may remain at the top and bottom.

Play a 4:3 image faithfully in a 16:9 screen in the standard vertical size and horizontally squeezed.*

Full

(Squeeze)

* An image with an aspect ratio of 16:9 shrunk

horizontally to 4:3 to display in a 4:3 screen

CHANNEL UP/DOWN button

PROGRAM SELECT buttons

TV AV1 AV2 AV3 AV4

RGB2 RGB1 AV6 AV5

4:3 Panoramic Zoom

Full Cinema

Full

Page 23

ENGLISH

Vertical picture position can be adjusted for [Panoramic], [Zoom] and [Cinema] mode as follows.

1. Press ZOOM button and SELECT buttons during picture size display.

2. Position display will appear.

3. Adjustment range of each picture size are as shown below. [Panoramic] - 12 to + 12 [Zoom] and [Cinema] - 31 to + 31

4. When 1080i/60 component signal is received, vertical position can be adjusted only one step up. (The range: 0 to +1)

Position + 31 Position - 31

Press Press

ATTENTION

Using a wide-screen monitor

• This monitor has a screen mode selection feature. If an incompatible screen mode is selected to play certain software, such as a TV program, the image would appear different from the original. Take this into consideration when making screen mode choices.

• Use of this monitor in its enlarged display mode with the wide feature enabled in coffee shops, hotels and other establishments for commercial or pubic viewing purposes could infringe on the copyright holder’s right protected by Copyright Law.

• When a normal 4:3 image is displayed over the entire screen in the Panoramic mode, parts of the periphery of the image may disappear and/or appear distorted in some cases. Use the 4:3 mode to view images, which were created in 4:3 mode.

This mode allows 4:3 content to be viewed without picture distortion.

• During RGB Input (RGB1 (set to [DVI-PC]) and RGB2 (set to [RGB]))

* Real mode gives the image of the same shape as it is displayed on a computer monitor.

This mode is only available for VGA (640 X 480) and WVGA (864 X 480).

Display area selection diagram (RGB input)

Resolution Full display Circular display

Full Normal Real

* VGA and W-VGA

only

Zoom1 Zoom2 Zoom3Display

640 X 480

(VGA)

800 X 600

(SVGA)

1024 X 768

(XGA)

1280 X 1024

(SXGA)

1600 X 1200

(UXGA)

Processes such as compression (thinning) and expansion are performed for the above signal display. Because of this, there is a possibility that flicker may become noticeable on Zoom (1 ~ 3) depending on the display contents. If this occurs, turning the Vertical Filter On can reduce the flicker.

OPERATING INSTRUCTIONS (continued)

Size Switching (continude)

Normal Full Zoom1

Real Zoom3 Zoom2

Page 24

OPERATING INSTRUCTIONS (continued)

Audio MuteVolume Adjustment

The audio volume can be temporarily mute by pressing the MUTE button of the remote control.

The volume can be adjusted by pressing the and buttons of the remote control (or the and volume buttons of the monitor unit).

Volume setting value

Adjustment status guide display

(The display color will change to magenta: volume ➝ Mute)

Volume setting value

Adjustment status guide display

• When a button is pressed, the volume adjustment status guide (magenta) will be displayed.

• The volume setting can be lowered by pressing the button while the audio is mute.

• The muting can be cancelled by pressing the button or MUTE button while the audio is mute.

• The audio from the headphone terminal is not mute.

• The audio from the speaker is automatically mute while

connecting the headphone to the headphone terminal of the side input (AV5).

When the MUTE button of the remote control is pressed again, the audio will be restored and the volume display (green) will appear.

• When a button is pressed, the volume adjustment status guide will be displayed.

• The volume will increase when the button is pressed while the guide is being displayed.

• The volume will decrease when the button is pressed while the guide is being displayed.

Volume 15

Page 25

ENGLISH

OPERATING INSTRUCTIONS (continued)

Power Swivel

• This feature controls the motorized stand. It allows turning the plasma display left or right using the remote control.

Make sure that the main power switch of the monitor is turned off when removing or connecting the power cord, the connector cables, and the speaker cables.

1. Press Swivel button.

The controlling icon appears on the screen.

• If the connecting cable is not connected, the indication "Not Available" appears.

• The swivel display disappears in about 6 seconds without any operation.

Swivel

2. Adjust for preferred angle.

Facing directions are displayed on the screen while the monitor is swiveled. Adjust by using key while the swivel display is on the screen. Swiveling angle of the monitor is available within 30 degrees from the front face.

ATTENTION

• Do not add excess power by hands while using the power swivel function. It could cause troubles.

• Do not get on and/or hang down the monitor. Do not swing the monitor back and forth and around either. It could cause the failure of the

stand.

• Do not put hands or faces close to the monitor while operating the swivel function. It could cause a physical injury. Use special caution in households where children are present.

• Do not put any object, like a vase, near the monitor in swiveling area. It would cause a breakage of the object and /or a failure of the stand.

• Place the monitor on the stable location, or the swivel function would not operate correctly. It would cause the malfunction.

• In the case of using the monitor wall mounted, be sure to detach the connecting cable between the monitor and the stand.

Caution when connecting the monitor with the stand

* This power swivel function might not be provided depending on a model.

• When detach the stand from the

monitor, make sure to detach the connector cable from the stand connection terminal on the rear of the monitor.

• Make sure that the direction of the connector for stand connecting cable is correct.

• When attach the stand to the monitor

once again, insert the connector cable into the stand connection terminal on the rear of the monitor.

Pinch right and left locks of the connector and pull out downward.

Insert until it clicks.

CAUTION

Page 26

OPERATING INSTRUCTIONS (continued)

Input Signal Screen Display

The input signal status can be displayed on the screen by pressing the RECALL button of the remote control.

• The display will go out in approximately 6 seconds.

Off-timer On-timer

TV position Name Sound mode

VIDEO

Off-timer On-timer

Input mode Signal mode

RGB

Off-timer On-timer

Input mode Signal mode Input horizontal frequency Input vertical frequency

RECALL button

-- -- Min.

OFF

-- -- : -- --

-- -- Min.

OFF

-- -- : -- --

-- -- Min.

OFF

-- -- : -- --

ABCDE

AV1

Composite

RGB2 RGB

H : 48.4kHz

V : 60.1 Hz

Page 27

ENGLISH

OPERATING INSTRUCTIONS (continued)

Displaying MULTI PICTURE

If the MULTI PICTURE button on the remote control is pressed, multi pictures will display. And then three types of the screen can be selected by pressing the MULTI MODE button on the remote control. The multi picture mode will change in the following sequence each time the MULTI MODE button is pressed.

Activating the Split mode from the TV screen

Pressing the MULTI PICTURE button one time will display 2 pictures.

• The speaker icon can be shifted left and right by pressing the and SELECT buttons; the audio will be output from the side on which the speaker icon is located.

• The same signal input cannot be selected for both screens at the same time.

• The TV channel can be changed by pressing the CHANNEL UP/DOWN buttons on the remote control.

• The signal input mode of picture-A or picture-B (the one that the speaker icon is located on) can be

selected by pressing INPUT SELECT button on the remote control.

• Pressing the MULTI PICTURE button once again will cancel the multi picture mode.

• Refer to the table for 2 pictures (Split) mode.

• For AV monitor model, TV screen cannot be displayed.

Activating the 4 pictures mode from the TV screen

Pressing the MULTI MODE button one time at the 2 pictures mode will display 4 pictures.

• Press and SELECT buttons to select picture A or picture B indicated by a red triangle. For pictures on right, press and SELECT buttons to select picture. The input display on the selected picture would change green.

• The TV channel can be changed by pressing the CHANNEL UP/DOWN buttons on the remote control.

• The audio can only be output from picture A in 4 pictures mode.

• The component signal input mode cannot be selected in pictures B. Refer to the table for 4 pictures

mode.

• Pressing the MULTI PICTURE button at the 4 picture mode will cancel the multi picture mode. And then, pressing the MULTI PICTURE button again will display the 4 pictures.

• For AV monitor model, TV screen cannot be displayed.

Activating the 12 pictures mode from the TV screen

Pressing the MULTI MODE button one time at the 4 pictures mode will display 12 pictures.

• Starting from channel 1, preset channels will automatically display in sequence on the 12 windows.

• This function activates only in TV mode.

• After several seconds, it refreshes the picture one by one.

• Pressing the MULTI PICTURE button at the 12 picture mode will cancel the multi picture mode. And then,

pressing the MULTI PICTURE button again will display the 12 pictures again.

• Pressing the MULTI MODE button at the 12 picture mode will display the 2 pictures (Split) mode.

• This function is not provided for AV monitor model.

INPUT SELECT

buttons

RECALL button

SELECT/ADJUST button ( , , , )

CHANNEL UP/DOWN button

MULTI PICTURE button

MULTI MODE

button

AV1

2 pictures (Split) 4 pictures 12 pictures

5AV1

1234

5678

9101112

Page 28

Activating the Split mode from the video input screen

Pressing the MULTI PICTURE button one time will display 2 pictures.

• The speaker icon can be shifted left and right by pressing the and SELECT buttons. The audio of the video will be output from the side on which the speaker icon is located.

• The same video input mode cannot be selected for both screens at the same time.

• Pressing the MULTI PICTURE button again will cancel the 2 pictures display.

• Refer to the table for 2 pictures (Split) mode.

Activating the MULTI PICTURE mode from the RGB input screen

Pressing the MULTI PICTURE button one time will display 2 pictures.

• This mode can be available from RGB1(DVI-PC) and RGB2(RGB) input.

• The speaker icon can be shifted left and right by pressing the and SELECT buttons. The audio of the

video will be output from the side on which the speaker icon is located.

• The sub-screen position can be selected up and down by pressing and SELECT buttons.

• The sub-screen can be selected with the AV1AV6, TV channel buttons from the status that the speaker

icon appears on the left side of AV✱ etc. as shown in the diagram to the right.

• Pressing the MULTI PICTURE button again will cancel the 2 pictures display.

• "Frequency Mode" in the Setup Menu should be set to Movie when sub-screen is the component signal of

1080i/50 or 1080i/60.

AV1: Displays the VIDEO input signal of the sub-screen.

NOTE

• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the multi picture display, the mode will not change to power save mode.

• Please be careful since image retention will occur if display is left in a multi picture display state for a long period of time.

2 Pictures (Split)

Input terminal

AV1



AV5

AV1, AV2, AV6 RGB1 RGB2

Sub

Main

AV1

 AV5

RGB1 RGB2

AV1 AV2 AV6

TV      

PAL, SECAM     

NTSC3.58/4.43     

576i, 576p      480i, 480p     

1080i/50      1080i/60     

720p/60     

STB

Component     

PAL

SECAM

NTSC3.58 NTSC4.43

576i

576p

480i

480p

1080i/50 1080i/60

720p/60

STB

Component

TELE TEXT

4 Pictures

Input terminal

AV1



AV5

AV1, AV2, AV6 RGB1 RGB2

Sub

Main

AV1

RGB1 RGB2

AV1 AV2 AV6

TV  

PAL, SECAM  

NTSC3.58/4.43  

576i, 576p   480i, 480p  

1080i/50   1080i/60  

720p/60  

STB

Component  

PAL

SECAM

NTSC3.58 NTSC4.43

576i

576p

480i

480p

1080i/50 1080i/60

720p/60

STB

Component

TELE TEXT

( : Available)

Teletext is available only for TV

( : Available)

OPERATING INSTRUCTIONS (continued)

Displaying MULTI PICTURE (continued)

AV1 AV2

RGB2

AV1

(Subscreen)

Main Sub

Main

Sub 1

Sub 2

Sub 3

Page 29

ENGLISH

OPERATING INSTRUCTIONS (continued)

FREEZE button

Picture Freezing

When the FREEZE button on the remote control is pressed, the screen transfers into the freeze mode.

• There are two types of freezing screen mode, Split and Strobe. These are possible to select at the “Freeze Mode” setting of the Function Menu.

• The Split mode will display 2 pictures from the same source on the screen with one active picture and the other still.

• The Strobe mode will display 12 pictures with the last picture active, while other 11 windows are still.

• Pressing the FREEZE button again changes the screen back to the normal picture.

• This function is also available from video input mode besides TV mode. Refer to the table for Freeze function

as below:

1234

5678

9101112

Active

[Split]

[Strobe]

Split Strobe

TV 

PAL, SECAM 

NTSC3.58/4.43 

576i 

480i  576p  480p 

1080i/50  1080i/60 

720p/60 

RGB, DVI-PC

( : Available)

Page 30

OPERATING INSTRUCTIONS (continued)

ROTATE button

PHOTO button PHOTO INPUT button

SLIDE SHOW button

Photo Input Display (37/42 only)

With the PHOTO button on the remote control, the pictures from a digital camera or Card Reader can be displayed.

Operating the Photo Input

1. Make sure that the power switch of the monitor is turned off/standby before using.

2. Set up the digital camera and its power in reference to the item relating to “connecting to PC” on the user manual of digital camera. *Insert the memory card when use the USB Card Reader.

3. Connect the monitor with the USB cable (see the above picture). Switch the input to the photo input by pressing PHOTO button. Then, turn

on the power of the digital camera. (Refer to the user manual of your digital camera).

4. The photo pictures will be displayed after a period of time turning on the camera, if connecting normally.

Digital Camera

USB Card Reader

USB cable

Page 31

Information

No message

“No Connection”

“No File”

“Loading”

ENGLISH

OPERATING INSTRUCTIONS (continued)

Photo Input Display (37/42 only) (continued)

Photo Input Function

Buttons on Remote Control Function Operating

Thumbnail-Size Image

• Select the pictures by using ( , , , ) key.

• Display the next or previous thumbnail-view of 16 images per one page by using (+), (–).

• Display the selected picture in the full size by pressing button.

Full-Size Image

• Return to the thumbnail-view by pressing button or return button.

Display the pictures in the thumbnail view. Return to the previous input display during the thumbnail or the full view.

• Each time pressed, the picture is rotated in the sequence of 90° ➝ 180° ➝ 270° ➝ 0°.

Press this to display the picture with rotate mode.

• Press the button while displaying the picture, the slide show begins from the first picture at a fixed interval.

• Press OK key, the slide show will be paused with OSD display [ OK start]. The slide show starts if let the condition for a minute.

• Return to the thumbnail images when finishing the all of pictures.

• Interval time during slide show can be changed from 5, 10 and 30

seconds in “Slide Interval” of function menu.

Press this to display the slide show of pictures.

PHOTO

ROTATE

SLIDE SHOW

1/ 6 2/ 6 3/ 6 4/ 6

5/ 6

6/ 6

o. 1/ 6

28/05/03 1600

× 1200

Thumbnail-Size Image Full-Size Image

• Specification

• Error Information

Max number of picture

Max number of pixel

Application

 Digital Camera corresponding to DCF standard.  USB Card Reader with the memory containing pictures had taken by  camera.

8176 x 8176 JPEG format

500

PHOTO INPUT

Accessing

Normal

Not insert USB

Not available format

Abnormal

No File

Loading Files

Page 32

OPERATING INSTRUCTIONS (continued)

Photo Input Display (37/42 only) (continued)

• The picture may not be displayed in case of editing by computers.

• Do not connect any apparatus other than a digital camera and a USB card reader to the photo input connector. It causes the malfunction.

• Do not connect a digital camera and USB card reader with USB HUB. Pictures may not be displayed correctly, or it causes the malfunction.

• Insert only one memory even though the USB card reader has multiple slots for memory card. Pictures in multiple memory cannot be seen

at the same time.

• Certain types of digital cameras or card readers may not work with this photo input function.

• Digital cameras with low battery power may not properly display photos in this input.

• This function does not work for audio and moving images taken other than a digital camera.

• Response time might vary according to each image content when switching pages.

• Contrast will decrease automatically if stationary images such as digital still photos are left on the screen for more than 3 minutes.

• The OSD message “No Connection” is displayed in case of the incomplete connection with USB cable and connection to a digital camera

or USB card reader without the memory card.

• The menu items other than “Picture” and “Function” are not available with grayed-out display.

• The functions of the multi picture, CH selection, freeze mode, aspect, mode display, and so on are not available.

• During blinking LED which indicates the access of a digital camera or USB card reader, or displaying “Loading”, do not turn the power

off/standby mode nor remove/insert USB cable and memory card.

• The picture may not be displayed correctly, depending on the connecting device in case of extending the USB cable.

* This photo input function might not be provided depending on a model.

CAUTION

Page 33

ENGLISH

OPERATING INSTRUCTIONS (continued)

MENU button

RECALL button

SELECT/ADJUST buttons ( , , , )

OK button

RETURN button

Using the Menu Screen (On-screen display system)

When the MENU button is pressed, the adjustment menu screen will be displayed; from there, PC signal adjustment and setting is possible by using the SELECT button, ADJUST button and OK button.

• Refer to - concerning the adjustment items and the settings.

Example: Selecting the Picture screen

1. Press the MENU button to display the Main Menu

screen.

2. Press the OK button to display the Picture Menu

screen. (Use the and SELECT buttons to select other items.)

3. Use the and SELECT buttons to select the item to

be adjusted and then use the and ADJUST buttons to adjust (example: Contrast).

• Press the RETURN button to return to the previous screen.

• If there is no operation for a period of one minute, the Adjustment

Menu screen will be closed automatically.

34 46

Picture Audio Timer Function Setup Language Select OK Set

Picture Contrast : + 31 Brightness : – 31 Color : 0 Tint : + 31 Picture Enhancement : Off Color Temperature : Normal Color Temp.Adjust Reset Reset Select Return Exit

Contrast + 31 Next / Prev Adjust Return

Page 34

OPERATING INSTRUCTIONS (continued)

SETUP MENU (TV mode)

Picture Audio Timer

Function Setup Language Select OK Set

Setup Auto Tuning Manual Tuning Fine Tuning Sort Teletext Language Auto Off Off

Select Set Return

Setup Auto Tuning Manual Tuning Fine Tuning Sort Teletext Language Auto Off Off

Select Set Return

Setup Auto Tuning Manual Tuning Fine Tuning Sort Teletext Language Auto Off Off

Select Set Return

Setup Auto Tuning Manual Tuning Fine Tuning Sort Teletext Language Auto Off Off

Select Set Return

Setup Manual Tuning Position 99 Frequency 250MHz Name ABCDE Sound System BG Color System Auto Skip Off NR Off Antenna Att. Off Select Return Exit

Setup Prog.No.199 Fine Tuning +56 Select Adjust Return

Setup Sort Position Name MHz 100 ABCDE 62MHz 101 BBC1 83MHz 102 ----- 97MHz 103 BBC 106MHz 104 FGHIJ 175MHz 105 XYZAB 189MHz 106 ----- 199MHz 107 ----- 225MHz

Select Return Exit

Setup Auto Tuning Mode Position Search Select Set Return

Setup Auto Tuning

Scanning Channel Number: 33

Cancel

Setup Auto Tuning Manual Tuning Fine Tuning Sort Teletext Language Auto Off Off

Select Set Return

Setup Teletext Language West Europe East Europe Cyrillic Greek/Turkish Select Return Exit

Page 35

ENGLISH

OPERATING INSTRUCTIONS (continued)

SETUP MENU (TV mode) (continued)

Selected characters Setup hint

Select the channel entry method between position setting or direct setting. And press the OK button to fix it.

• If [Position] is selected, the screen display will be numbers (1~199 and AV00).

• If [Direct] is selected, the screen display will be C✱✱ at the channel 0~99 and S✱✱ at the channel 100~199.

Press the OK button and it starts the auto tuning.

This is used to input the name of the TV station within 5 letters. After fixing the cursor on the first digit, select a letter by and SELECT buttons and move to next digit by ADJUST button. Press the OK button again after finished.

• Selectable letters are “0”~”9”, ”A”~”Z”, “+”, “–”, ” ”(blank), ”,”(comma) and ”.”(period) .

• If [Position] has been selected, search the frequency here by

pressing and buttons.

• If [Direct] has been selected, this function will be not available (grayed out).

Select the sound system through the 5 different settings.

Select the color system through the 5 different settings.

If this is set to On, it helps to reduce the noise interference visible on the screen, especially in the weaker signal reception areas.

If this is set to On, that position will be skipped while selecting positions by CHANNEL UP/DOWN buttons. This is automatically set to On for those non-broadcasting channels.

After completing the fine-tuning, press the RETURN button to exit this mode.

• The variable range is -56 ~ +56.

Select the teletext language through the 4 settings.

• Select West Europe when watch in Singapore, Australia, Malaysia, and so on.

If this is set to On, the power will be turned off when there is no transmission signal and no operation for about 10 minutes in the TV mode.

Press OK button at the a line that is required to change order, then the characters will change to green. And move it up or down in the list by pressing and SELECT buttons. And press OK button to complete it. Press the RETURN button to exit.

If this is set to On, it helps to reduce the noise interference visible on the screen in case of strong airwave.

Set the position number(0~199) or channel number(C✱✱, S✱✱) by (+) (–) CHANNEL UP/DOWN buttons.

Auto Tuning

Manual Tuning

Position

Frequency

Name

Sound System

Color System

Skip

Antenna Att.

Fine Tuning

Sort

Increasing the frequency data for the main tuner.

Decreasing the frequency data for the main tuner

––

(When the Mode in Auto Tuning menu is set to [Direct], this function will be not available (grayed out).)

(A Line of position List)

Teletext Language

Auto Off

Mode

Position Direct

( :a letter)

Auto M BG

DK I

Auto PAL SECAM

NTSC3.58 NTSC4.43

Off On

Page 36

OPERATING INSTRUCTIONS (continued)

SETUP MENU (Video mode)

Selected characters Setup hint

System

Color System

Video Input

AV1~AV5

AV1, AV2

Do not change the original setting. (System1 : Europe/Asia, System2 : North America)

RGB1

This should correspond to the signal mode of the signal from the equipment that is connected to RGB1 DVI terminal.

This should correspond to the color system of the signal from the equipment that is connected to AV1~AV5 video input terminal.

• Normally, set this to Auto. The system of the input signal will be automatically recognized.

• If the input signal contains much noise or has a low level at Auto and the operation is found erratic, set this to match the input signal.

• When the component signal is received, this would be not available (grayed out).

This should correspond to the signal mode of the signal from the equipment that is connected to AV1, 2 video input terminal.

• Normally, set this to Auto. The signal mode of the input signal will be automatically recognized.

• If the input signal contains much noise or has a low level at Auto and the operation is found erratic, set this to match the input signal.

RGB2 (1st step)

This should correspond to the signal mode of the signal from the equipment that is connected to RGB2 D-sub terminal.

RGB2 (2nd step)

This step should be set only when [Component] is selected on the 1st step. This should correspond to the signal mode of the signal from the equipment that is connected to RGB2 D-sub terminal.

• Normally, set this to Auto. The signal mode of the input signal will be automatically recognized.

• If the input signal contains much noise or has a low level at Auto and the operation is found erratic, set this to match the input signal.

Picture Audio Timer Function Setup Language Select OK Set

Setup System System 1 Color System Video Input RGB1 DVI-STB RGB2 Component HDTV

Select Set Return

Setup System System 1 Color System Video Input RGB1 DVI-STB RGB2 Component HDTV

Select Set Return

Setup Color System

AV1 Auto AV2 PAL AV3 SECAM AV4 PAL AV5 Auto

Select Return Exit

Setup Video Input

AV1 Auto AV2 Auto

Select Return Exit

System1 System2

System1

Auto PAL SECAM

NTSC3.58 NTSC4.43

System2

Auto NTSC-M

PAL-N PAL-M

Auto HDTV SDTV/DVD

DVI-PC DVI-STB

RGB Component

Auto HDTV SDTV/DVD

Page 37

ENGLISH

OPERATING INSTRUCTIONS (continued)

SETUP MENU (RGB mode: RGB1 (DVI-PC), RGB2 (RGB))

Selected characters Setup hint

Auto Adjust*

Horizontal Position

Vertical Position

Horizontal Clock

Clock Phase

Reset

Input Level

Frequency Display

WVGA Type

WXGA Mode

Horizontal Position, Vertical Position, Horizontal Clock and Clock Phase are adjusted automatically.

Adjust the left-side display position. Screen display changes to Magenta color if beyond the available range. (This function is only for RGB2. It’s not available (grayed out) for RGB1 (DVI-PC).)

Adjust the vertical display position. Screen display changes to Magenta color if beyond the available range. (This function is only for RGB2. It’s not available (grayed out) for RGB1 (DVI-PC).)

Adjust for maximum character clarity. (This function is only for RGB2. It’s not available (grayed out) for RGB1 (DVI-PC).)

Adjust for clear character visibility. (This function is only for RGB2. It’s not available (grayed out) for RGB1 (DVI-PC).)

The original factory settings for the items of this Menu page can be restored by pressing the OK button.

Normally set to 0.7 V. If white is found to spread across the screen, set to 1.0 V. (This is effective only for RGB2.)

Set this to Off if the frequency information of the Input Signal Screen Display is not required.

This is only available for W-VGA signal. When it is set to On, the display area mode can be selected Full or Real. (With RGB1 INPUT, the screen remains the same. RGB2 (ANALOG) INPUT only)

This is only available for W-XGA signal. (RGB2 (ANALOG) INPUT only)

Adjust Pressing the OK button here, Automatic regulation is started.

Moves the horizontal position to right.

Moves the horizontal position to left.

Moves down the vertical position.

Slows the dot clock phase (shifts slightly to left).

(off the function) (waiting to reset)

Advances the dot clock phase (shifts slightly to right).

Reduces the dot clock frequency (shrinks the right side).

Increases the dot clock frequency (expands the right side).

Moves up the vertical position.

–

Picture Audio Timer Function Setup Language Select OK Set

Setup Auto Adjust Adjust Horizontal Position 0 Vertical Position + 31 Horizontal Clock – 20 Clock Phase 10 Reset Reset Select Set Return

Setup Input Level 0.7V Frequency Display Off WVGA Type Off WXGA Mode Off Vertical Filter On Frequency Mode Movie RGB1 DVI-PC RGB2 RGB Select Set Return

Horizontal Position 0 Next / Prev Adjust Return

Clock Phase 10 Next / Prev Adjust Return

0.7V 1.0V

Off On

Off 1280x768 1366x768

Page 38

Selected characters Setup hint

Vertical Filter

Frequency Mode

RGB1

RGB2 (1st step)

RGB2 (2nd step)

Turn On when concerned about screen flicker.

Set to Movie when viewing moving images on a personal computer.

This should correspond to the signal mode of the signal from the equipment that is connected to RGB1 DVI terminal.

This should correspond to the signal mode of the signal from the equipment that is connected to RGB2 D-sub terminal.

This step should be set only when [Component] is selected on the 1st step. This should correspond to the signal mode of the signal from the equipment that is connected to RGB2 D-sub terminal.

• Normally, set this to Auto. The signal mode of the input signal will be automatically recognized.

• If the input signal contains much noise or has a low level at Auto and the operation is found erratic, set this to match the input signal.

OPERATING INSTRUCTIONS (continued)

SETUP MENU (RGB mode: RGB1 (DVI-PC), RGB2 (RGB)) (Continued)

* Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Adjust manually to optimize them.

Auto HDTV SDTV/DVD

Off On

Movie PC

DVI-PC DVI-STB

RGB Component

Page 39

ENGLISH

FUNCTION MENU

Selected characters Setup hint

This moves the picture around the screen in small amounts, at set intervals, to reduce the panel image retention. This is where stationary objects, such as screen logos, leave a slight image visible after they should have disappeared.

This is used to reduce the panel image retention that can occur with stationary pictures by the white field signal. Select On (continuous operation) or 60 Min. (time limit operation) and press the OK button. Press the MENU or RETURN button on the remote control to return to normal viewing.

This turns the gray sidebars to the black sidebars when watching normal mode screen size area. It is always set to Off when the monitor powered On. It is recommended to set to Off to reduce the panel image retention. This is not available for the photo input function.

This is used to reduce power consumption for video input when there is no video signal. Setting it On will lead the monitor to the standby mode when the AV input with no signal is selected.

This selects the display condition of the FREEZE mode between Split (2 pictures) and Strobe (12 pictures). This is grayed out and not available in the AV monitor.

This selects the screen display size of TV input that appears first when the main power turned on. This is grayed out and not available in the AV monitor.

This function is to suppress the contrast of the screen regardless of the Contrast setting in the Picture Menu. By this control, power consumption can be reduced or degradation of a panel can be mitigated. The order of power consumption is Extend 2 < Extend 1 < Normal. If the Contrast setting is changed when this item is set to Extend 1 or 2, it will be changed to Normal automatically.

This is used to reduce the panel image retention which is caused by especially displaying TV station logo. Brightness of 4 corners of the panel get lower than the center.

This is used to display images at set intervals during slide show. (37/42 only)

The original factory settings for the items of this Menu page can be restored by pressing the OK button.

On 60Min.

(off the function) (waiting to reset)

Screen Saver

Screen Wipe

Black Side Panel

Video Power Save

Freeze Mode

Default Zoom

Panel Life

Luminance Manager

Slide Interval

Reset

This can display the Input Signal Screen Display every time the input mode and signal mode are changed. Set to OFF if the Input Signal Screen Display is not needed when switching signals.

Mode Display

Assigns ID numbers to the monitors so that they can be controlled individually (up to 7 monitors can be controlled).

ID Number

This function can change each level if RGB signal invert to reduce the panel image retention. When this function is required to use, select On (continuous operation) or 60Min. (time limit operation) and press OK button. And press the Menu or return button to exit.

On 60Min.Inverse

This function is also provided against the image retention. If time is set for this item, the screen changes into the white pattern when the monitor enters power save mode, and it will continue for the period of setting time.

Standby White

Normally set to 2.2.

Gamma

AV monitor only

OPERATING INSTRUCTIONS (continued)

Picture Audio Timer Function Setup Language Select OK Set

Function Screen Saver Off Screen Wipe On 60Min. Black Side Panel Off Video Power Save Off Freeze Mode Split Default Zoom Panoramic Panel Life Nomal Luminance Manager Off Slide Interval 5Sec. Reset Reset Select Set Return

Function Mode Display Off ID Number 1 Inverse On 60Min. Standby White Off Gamma 2.2 Reset Reset Select Set Return

Off 5Min. 10Min.

60Min. 40Min. 20Min.

Off On

Split Strobe

Panoramic 4:3

Normal Extend 1 Extend 2

Off On

5Sec. 10Sec. 30Sec.

Off On

1 2 3 4

7 6 5

Off 15Min. 30Min.

120Min. 60Min.

2.2 2.8

Page 40

Picture Color Temp. Adjust On Amplitude Red – 63 Green 0 Blue – 31 Cut Off Red + 31 Green 0 Blue + 31 Reset Reset Select On/Off Return

Picture Color Management On

Magenta + 60 Red + 30 Yellow 0 Green + 60 Cyan + 30 Blue 0

Reset Reset Select On/Off Return

OPERATING INSTRUCTIONS (continued)

PICTURE MENU (TV/Video mode)

Picture Audio Timer Function Setup Language Select OK Set

Picture Picture Mode Dynamic Contrast +31 Brightness -31 Color 0 Sharpness +15 Tint 0 Color Temperature Normal Contrast Mode Normal Reset Reset Select Set Return

Picture Dynamic YNR Off CNR Off Film Mode On PAL Comb Filter On LTI Off CTI Off Black Enhancement Off Auto Color Off Reset Reset Select Set Return

Picture Mode Dynamic Next/Prev Select Return

Contrast Mode Normal Next/Prev Select Return

YNR Off Next/Prev Select Return

Picture Dynamic YNR Off CNR Off Film Mode On PAL Comb Filter On LTI Off CTI Off Black Enhancement Off Auto Color Off Reset Reset Select Set Return

Picture Dynamic Color Temp. Adjust Color Management Color Decoding Select Set Return

Auto Color Off Next/Prev On/Off Return

Picture Dynamic Color Temp. Adjust Color Management Color Decoding Select Set Return

Picture Color Decoding

RGB R G B Red 0 Green + 60 Color 0 Tint + 31

Reset Reset

Select Return Exit

Page 41

ENGLISH

OPERATING INSTRUCTIONS (continued)

PICTURE MENU (TV/Video mode) (continued)

Selected characters

Picture Mode

Setup hint

Dynamic: This setting is best for very bright ambient lighting. Natural: This setting is for normal lighting conditions. Cinema: This setting is best for watching movie.

Contrast

Adjust for maximum visibility to suit the ambient brightness. This can adjust further till [+40] by pressing and holding SELECT button at [+31]. The color for [+32] to [+40] numbers will change from white to magenta. This special mode is better for dark scenes. For normal viewing we recommend that the Contrast is set to [+31]. "Panel Life" in the Function Menu should be set to Normal when this Contrast setting is adjusted.

Narrows the gap between brightness and darkness.

Broadens the gap between brightness and darkness.

Brightness

Black is subdued for increased overall darkness.

Black is set off for increased overall brightness.

Adjust to preference.

Color Temperature

Normally set to Cool.

Contrast Mode

Dynamic:Emphasizes the differences between video shadings to

improve the feeling of contrast.

Normal : The gradation of an image is reproduced as faithfully as

possible.

Auto:Detects image brightness and automatically adjusts for natural

brightness.

Color

Decrease color intensity. Increase color intensity. Adjust to preference.

Sharpness

Soft Sharp

Normally set to Centre position Shift to the minus (-) side for a softer effect and plus (+) for sharper picture.

Reset

(off the function) (waiting to reset)

Brighter scene is decreased in reddish color.

Brighter scene is increased in reddish color.

The original factory settings for the items of this Menu page can be restored by pressing the OK button.

Tint

Enhances red and weakens green.

Enhances green and weakens red.

This is not available to adjust when receiving PAL/SECAM signal. Then the character will be grayed out. Adjust for most realistic skin color.

PAL Comb Filter

This is available only when receiving a PAL composite signal. Turn On to reduce the discolorations in fine picture detail and provides purer color.

YNR

Performs picture signal noise reduction. Turn up to reduce noise.

LTI

Adjusts the sharpness of the picture signal.

CNR

Performs color signal noise reduction. Turn up to reduce noise. And it will be fixed as Off only when selecting DVI-STB mode.

Color Temp. Adjustment

Turn On when you wish to change color temperature depending on the user's preference.

Adjust color temperature depending on the user’s preference. These settings are independently stored in each of the 4 Color Temperature modes.

Film Mode

On:Automatically detects the movie film material and faithfully reproduces the original film image. Off:Set to OFF when switching between images does not appear natural.

CTI

Adjusts the sharpness of the color signal.

Black Enhancement

Adjusts the black level compensation.

Auto Color

This is available only when receiving an NTSC composite/S.Video signal. This monitors and adjusts the color to maintain constant color levels. It also maintains natural flesh tones while preserving fidelity of background colors.

Red

Brighter scene is decreased in greenish color.

Brighter scene is increased in greenish color.

GreenAmplitude

Brighter scene is decreased in bluish color.

Brighter scene is increased in bluish color.

Blue

Dark scene is decreased in reddish color.

Dark scene is increased in reddish color.

Red

Dark scene is decreased in greenish color.

Dark scene is increased in greenish color.

Green

Cut Off

Dark scene is decreased in bluish color.

Dark scene is increased in bluish color.

Blue

Dynamic

Natural

Cinema

Cool Normal Warm Black / White

Normal Auto Dynamic

Off Low High

Off On

Off Low Middle High

Off On

Page 42

OPERATING INSTRUCTIONS (continued)

PICTURE MENU (TV/Video mode) (continued)

Selected characters

Color Management

Setup hint

Turn On when the original balance of each color is required to adjust depending on the user’s preference.

This adjusts listed colors individually to make them either deeper or more pure. These settings are independently stored in each of the 4 Color Temperature modes.

Select the single color screen when that is required to adjust R/G/B level individually depending on the user’s preference. And set it back to RGB mode that indicates all color after adjusting. Press the OK button every time the setting is changed.

This adjusts R/G/B level or tint to make the color appear natural for the user’s preference. These settings are independently stored in each of the 4 Color Temperature modes. This does not work for receiving PAL/SECAM signal. Guide display become unavailable to select with gray color.

Magenta

Magenta is weakened. Magenta is strengthened.

Red

Red is weakened. Red is strengthened.

Yellow

Yellow is weakened. Yellow is strengthened.

Green

Green is weakened. Green is strengthened.

Cyan

Cyan is weakened. Cyan is strengthened.

Blue

Blue is weakened. Blue is strengthened.

Color Decoding

Red

Darkens red only. Lightens red only.

Green

Darkens green only. Lightens green only.

Color

Decrease color intensity. Increase color intensity.

Tint

Enhances red and weakens green.

Enhances green and weakens red.

Off On

RGB R G B

Page 43

ENGLISH

Selected characters

Contrast

Narrows the gap between brightness and darkness.

Broadens the gap between brightness and darkness.

Setup hint

Adjust for maximum visibility to suit the ambient brightness. This can adjust further till [+40] by pressing and holding SELECT button at [+31]. The color for [+32] to [+40] numbers will change from white to magenta. This special mode is better for dark scenes. For brighter scene some parts of the picture might not be clear. We recommend to set at [+31]. "Panel Life" in the Function Menu should be set to Normal when Contrast setting is adjusted.

Brightness

Black is subdued for increased overall darkness.

Black is set off for increased overall brightness.

Adjust to preference.

Picture Enhancement

Sets the clarity of small details to the desired level.

Color Temperature

Normally set to Normal.

Color Temp. Adjustment

Amplitude

Cut Off

Reset

Turn On when you wish to change color temperature is required to adjust depending on the user’s preference.

The original factory settings for the items of this Menu page can be restored by pressing the OK button.

Color

Decrease color intensity. Increase color intensity. Adjust to preference.

Tint

Enhances red and weakens green.

Enhances green and weakens red.

This is not available to adjust when receiving PAL/SECAM signal. In this case the character will be grayed out. Adjust for most realistic skin color.

Brighter scene is decreased in reddish color.

Brighter scene is increased in reddish color.

Brighter scene is decreased in greenish color.

Brighter scene is increased in greenish color.

Brighter scene is decreased in bluish color.

Brighter scene is increased in bluish color.

Dark scene is decreased in reddish color.

Dark scene is increased in reddish color.

Dark scene is decreased in greenish color.

Dark scene is increased in greenish color.

Dark scene is decreased in bluish color.

(off the function)

Dark scene is increased in bluish color.

(waiting to reset)

Red

Green

Blue

Red

Green

Blue

Adjust color temperature depending on the user’s preference. These settings are independently stored in each of the 4 Color Temperature modes.

OPERATING INSTRUCTIONS (continued)

PICTURE MENU (RGB mode)

Picture Audio Timer Function Setup Language Select OK Set

Picture Contrast : + 31 Brightness : – 31 Color : 0 Tint : + 31 Picture Enhancement : Off Color Temperature : Normal Color Temp.Adjust Reset Reset Select Set Return

Contrast + 31 Next / Prev Adjust Return

Color Temperature Normal Next/Prev Select Return

Picture Color Temp. Adjust On Amplitude Red – 63 Green 0 Blue – 31 Cut Off Red + 31 Green 0 Blue + 31 Reset Reset Select On/Off Return

Off Low Middle High

Cool Normal Warm Black / White

Off On

Page 44

OPERATING INSTRUCTIONS (continued)

AUDIO MENU

Selected characters

Audio Mode

Setup hint

Movie: This selects the audio suitable for Movie. Music: This selects the audio suitable for Music. Speech: This selects the audio suitable for News, Talk show etc. Favorite: This mode should be adjusted depending on user’s preference.

Dynamic Bass

Dynamic Bass takes advantage of the ability of the human ear to be able to distinguish between two different tones. By using this ability, Dynamic Bass gives enhanced bass sound that otherwise would not be heard. Adjust it depending on the user’s preference.

Treble

Suppresses treble. Enhances treble. Adjust to preference.

Bass

Suppresses bass. Enhances bass. Adjust to preference.

Balance

Suppresses right-side sound. Suppresses left-side sound. Adjust to preference.

Headphone Volume

Headphone Select

Turns down the volume. Turns up the volume.

(off the function) (waiting to reset)

This is to set the volume for headphone. The audio from the speaker is mute when connected to headphone terminal.

A/B: During the 2 picture mode, the audio will be output from

headphone on A (left picture) or B (right picture) to be selected. The speaker icon is located on the selected picture.

B: The audio of B (right picture) is from headphone.

Matrix Surround

This features the spacious sound effects of a stadium.

Perfect Volume

This will automatically adjust volume so each channel and input has the same average volume level.

Reset

The original factory settings for the items of this Menu page can be restored by pressing the OK button.

Picture Audio Timer Function Setup Language Select OK Set

Movie Music Speech Favorite

Off Low Middle High

Off On

A/B B

Audio Audio Mode : Movie Treble : + 10 Bass : – 10 Balance : 0 L R Dynamic Bass : Middle Matrix Surround : Off Perfect Volume : Off Reset Reset Select Set Return

Audio Headphone Volume : + 20 Headphone Select : A/B

Select Set Return

Page 45

ENGLISH

TIMER MENU

LANGUAGE MENU

Select a language by ▲ and ▼ SELECT buttons and press the OK button.

Selected characters

Off Timer

On Timer

- - ( : - - ) hours

(- - : ) - -

minutes

Setup hint

This function automatically sets the power to standby status when the indicated time period has elapsed.

This automatically sets the power from standby to ON when the indicated time period has elapsed. The settable time is 00:00~11:59. Input the required time by

▲ and ▼ SELECT buttons on the remote control.

OPERATING INSTRUCTIONS (continued)

Picture Audio Timer Function Setup Language Select OK Set

--Min. 30Min. 60Min. 120Min. 90Min.

Picture Audio Timer Function Setup Language Select OK Set

Timer Off Timer : 30Min. On Timer : - - : - - Select Adjust Return

Language

Select Return Exit

English

Page 46

Picture Mode Contrast Brightness Color Shapness Tint Color Temperature Contrast Mode YNR CNR Film Mode PAL Comb Filter LT I CTI Black Enhancement Auto Color Color Temp. Adjust

R Amplitude

G Amplitude

B Amplitude

R Cut Off

G Cut Off

B Cut Off

Color Management

Magenta

Red Yellow Green

Cyan

Blue

Color Decoding

Red Green

Color

Tint

Audio Mode Treble Bass Balance Dynamic Bass Matrix Surround Perfect Volume Headphone Volume Headphone Select

1 setting is registered. For every input function and every Picture Mode, 1 setting is registered.

For every Color Temperature, 1 setting is registered.

For every input function and every Picture Mode, 1 setting is registered. 1 setting is registered.

For every Color Temperature, 1 setting is registered. For every input function and every Picture Mode, 1 setting is registered. 1 setting is registered. For every Audio Mode, 1 setting is registered. 1 setting is registered. For every Audio Mode, 1 setting is registered.

Screen Saver Screen Wipe Black Side Panel Video Power Save Freeze Mode Default Zoom Panel Life Luminance Manager Slide Interval Mode Display ID Number Inverse Standby White Gamma System Color System

AV1 AV2 AV3 AV4 AV5

Video Input

AV1

AV2 RGB1 RGB2 Auto Adjust Horizontal Position Vertical Position Horizontal Clock Clock Phase Input Level Frequency Display WVGA Type WXGA Mode Vertical Filter Frequency Mode

Function

Setup

Language

OTHER FUNCTIONS

Automatic Store

Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.

Picture

Audio

Menu Display Registration condition

1 setting is registered. (not registered) 1 setting is registered. 1 setting is registered.

1 setting is registered.

For every input function, 1 setting is registered.

1 setting is registered.

(not registered) For every signal Mode, 1 setting is registered. (Only for RGB2)

1 setting is registered.

Menu Display Registration condition

• The previously recorded items will be lost.

• The signal mode can be identified by the horizontal/vertical sync

frequency and the sync signal polarity. Different signals with which all the elements are the same or similar will be handled as the same signal.

Page 47

ENGLISH

A2 / NICAM / Sound Multiplex (TV mode)

• The CH I / II button is only useful for NICAM and sound multiplex signals. Otherwise pressing this button will have no effect.

BILINGUAL / DUAL sound broadcast

When bilingual program is received, sound mode display appears in yellow as shown on right. Press the CH I / II button to select the sound to be heard. Each time the button is pressed, I, II or ▼ (force mono) appear cyclically on the screen. When receiving NICAM signals, NICAM display will appear as below.

NICAM [II]

STEREO sound broadcast

When a stereo program is received, sound mode display will appear in red, and you can press the CH I / II button to select between stereo and mono sound.

Each time the button is pressed, or ▼ (force mono) appear cyclically on the screen. When receiving NICAM signals, NICAM display will appear as below.



Monaural sound broadcast

When a monaural program is received, sound mode display will appear in green. You can press the CH I / II button to select the sound mode between monaural and forced mono (sound is same). Each time the button is pressed,  or ▼ (force mono) appear cyclically on the screen.

NOTE

• If sound signal is not strong enough for quality reception, press the CH I / II button until ▼ appears on the screen to receive a clear mono sound.

• If sound has hiss noise or keep switching between stereo and mono mode due to signal condition, press the CH I / II button until ▼ appears

on the screen to receive a clear mono sound.

OTHER FUNCTIONS (continued)

Audio Switching

Sound multiplex signal received

Yellow

[I]

NICAM signal received

NICAM [I]

Select I, II or (force mono) to hear the CH I, CH II or MONO broadcast respectively.

Yellow

[II]

YellowYellow

NICAM [II]

Sound multiplex signal received

Red Green

Green

NICAM signal received

NICAM

Select or (force mono) to hear the STEREO or MONO broadcast respectively.

Red

Green

Page 48

OTHER FUNCTIONS (continued)

Power Save Mode

When the RGB1, RGB2 input is selected

• When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the computer is not being used to reduce power consumption by this unit.

Returning to operating status

• Operate the personal computer, or press either the INPUT SELECT button of the main unit or the RGB1/RGB2 buttons of the remote control.

DVD Player/STB Selection

• You can use this remote control to operate the selected maker of DVD player by pressing the following buttons on the remote control simultaneously.

<“DVD” Selection>

Makers of DVD player Set Maker Set Type Makers of DVD player Set Maker Set Type

HITACHI

FUNAI

Pioneer

Panasonic

TOSHIBA

Philips

JVC

SAMSUNG

Sony

Sharp

1 31

RCA

0 1

Mitsubishi

ONKYO

ZENITH

THOMSON

SHINCO

SKYWORTH

BUBUKO

DENON

2-4-12

RED

GREEN

YELLOW

BLUE

<“SAT” Selection>

Makers of STB player Set Maker Set Type

HITACHI

TOSHIBA

DGTECH

Panasonic

1 21

RGB sync signal

Horizontal Yes No Yes No

Vertical

PC signal

Operation mode

Indicating lamp

Power consumption

Active (normal display)

Lights green

245W (32) 320W (37) 380W (42)

Blank (no display)

Off

Lights orange

3W or less (RGB1) 1W or less (RGB2 ; 100V

≤AC≤120V)

3W or less (RGB2 ; 120V<AC<240V)

Yes Yes No No

Page 49

ENGLISH

OTHER FUNCTIONS (continued)

DVD Player/STB Selection (continued)

Set up hint

Example) HITACHI DVD 

To operate HITACHI DVD player, press and hold the button, followed by the  button.

1. Press button to indicate the lamp of DVD on the remote control. During LED lighting, press and  to set up the maker.

2. Release the  button once while keeping button, press the  button again to set the maker type.

* After set up the maker type, press the button related with

DVD, and make sure that DVD player is working. In case DVD player does not work, repeat 1 and 2 with other numbers for the maker type to make sure it. (In this example, press  or .)

NOTE

• Not all models of the listed makers can be operated using

this remote control.

Signal Check (RGB mode)

Changes in the signal status are displayed on the screen as they arise.

Status Display Action

When Mode Display is set to ON, the input signal is switched or when the RECALL button is pressed.

A guide is displayed for the input terminal and the horizontal and vertical sync frequency.

When the sync signal is no longer detected.

• A guide displays No Sync. Signal, and Power Save (for approx. 5 sec.)

• When the condition continues where the sync signal cannot be detected, indicator lamp of power source changes in orange and the mode switches to power save mode.

Recheck the personal computer power switch status and the connection status.

When the input signal does not match the monitor specifications or is in an unstable status.

A guide displays Invalid Scan Freq.

Recheck the input signal specifications.

54 57

RGB

RGB2 RGB

H : 48.4kHz

V : 60.1 Hz

-- -- Min.

OFF

-- -- : -- --

! No Sync. Signal

! Invalid Scan Freq.

Page 50

TROUBLESHOOTING

Symptoms That Seemingly Appear to be Failures

Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.

Customer servicing can be hazardous.

Symptom Point to check See page

• No picture with the power-indicating lamp off.

• Check the way the power cable is connected.

• Press the power switch.

• The power indicating lamp is normally lit but

no picture.

• Check the contrast and brightness settings (adjust them for higher contrast and brightness).

• Check the way the signal cable is connected.

• The message “Invalid Scan Freq.” is dis-

played.

An input signal is not received normally.

• Check to see if the input signal matches the monitor specifications.

• Check the way the signal cable is connected.

• The message “No Sync. Signal” or “Power Save” is displayed.

• No picture with the power indicating lamp

lights in orange.

No sync signal is detected.

• Check the way the signal cable is connected.

• Make sure that the switch of the computer, imaging equipment,

etc., is turned on.

• Make sure the computer is not in the power-save mode.

• Check to see if the input selection matches the connection

terminal.

• The display image appears flowing slantwise.

• Text displayed across the screen appears vertically streaked, with the characters in vertical columns blurred.

• Adjust the dot clock frequency and phase. (Adjust the dot clock frequency first, the dot clock phase next.)

(RGB input)

• Text displayed across the screen appears blurred.

• A fine pattern flickers when displayed on the screen.

• Adjust the dot clock phase for the clearest viewing. (RGB input)

• The remote control does not work. • Check to see if the batteries are loaded in the remote control in opposite direction.

• Check to see if the batteries in the remote control are OK.

• The display image does not appear in the

normal position.

• Check to see if the displayed input signal match the monitor specification by pressing button.

• Turn off the screen saver.

• The display has picture missing on the

screen. (PC input mode only)

• Turn off the screen saver.

• The temperature of the display panel surface is high. • The plasma display panel is lighting the phosphors by the

discharge of internal radiation. In some cases, this may cause the temperature of the panel surface to increase. Please note that this is not a malfunction.

–

WARNING

! No Sync. Signal

! Invalid Scan Freq.

AAAAA

Page 51

ENGLISH

TROUBLESHOOTING (continued)

Symptoms That Seemingly Appear to be Failures (continued)

Symptom Point to check See page

• If the direct frequency from the computer is below 85Hz, try a higher frequency (upper limit 85Hz). There may be a slight attenuation of the current image.

• Try turning the Vertical Filter On. For this case however, the vertical resolution will drop.

• Flickering in the form of horizontal lines oscillating up and down.

(PC INPUT MODE only)

• When used for long periods of time, the top of the monitor may heat up. This is not a malfunction.

• The top of the monitor heats up.

• The thicknesses of characters and lines may vary if images with

a vertical resolution greater than 512 lines are displayed; however, this is not a malfunction.

• Text characters are displayed with varying thicknesses.

–

• This sometimes occurs when a component output VTR such as the

480i is connected. This is not a malfunction; therefore, please take note that this may occer. When it does occur, change to composite output,or S.video output.

• The screen becomes dark and the images cannnot be seen during VTR special playback (fast forward, rewind)

• Sub pictures image might not be able to be displayed, depending on the combination. (Reter to the table of “2 picture mode” and “4 picture mode”)

• During multi picture mode, sub pictures are not displayed.

• The screen dicplay size is fixed at “Full” as receiving 1080i/60Hz,

1080i/50Hz, and 720p.

• The screen display sizes are not switched.

• Check the cable and output format of connecting device. (Reter to “Connecting to an Audio Visual Device”)

• Images from AV6 (HDMI) are not displayed.

• Check the connecting device and image format. (Reter to “Photo Input Display”)

• Images from Photo Input are not displayed.

–

• Coarse horizontal stripes appear in FULL display.

• There are locations on the screen that are different from

the periphery (*). *Points that do not light, points with brightness different from that of the periphery, points with color different from that of the periphery, etc.

• High-precision technology is used to manufacture the plasma display panel, However in some cases, there are minor defects in some parts of the screen. Please note that this is not a malfunction.

• Vertical stripes appear, depending on the screen contents. • The plasma display panel is lighting the phosphors by the discharge of internal radiation. Depending on the screen contents, in rare cases this may cause vertical stripes to appear because of failure to light. Please note that this is not a malfunction.

–

• Adjusting the Clock Phase will reduce the horizontal stripes.

(RGB input)

Page 52

TROUBLESHOOTING (continued)

Actions to Correct Abnormal Displays

Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the adjustments suggested below. (only for RGB2)

Symptom 1

Figure 1

Text displayed across the screen appears vertically streaked, with some characters blurred (Figure 1). (RGB input).

1) Press the MENU button. The Main Menu will be displayed.

2) Press the SELECT button and select Setup.

3) Press the OK button. The Setup Menu will be displayed.

4) Press the SELECT button and select Auto Adjust.

When adjustment is not possible with Auto Adjust

5) Press the MENU button. The Main Menu will be displayed.

6) Press the SELECT button and select Setup.

7) Press the OK button. The Setup Menu will be displayed.

8) Press the SELECT button and select Horizontal Clock. (Display fine patterns as characters or a vertical striped pattern over the entire screen during Horizontal Clock adjustment.)

9) Press the or ADJUST buttons and search for clear characters over the entire screen.

10) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.

Adjustment

procedure

Example

Symptom 2

Figure 2 Figure 3

Text displayed across the screen appears blurred in its entirety (Figure 2). A fine pattern flickers when displayed on the screen (Figure 3).

1) Press the MENU button. The Main Menu will be displayed.

2) Press the SELECT button and select Setup.

3) Press the OK button. The Setup Menu will be displayed.

4) Press the SELECT button and select Auto Adjust.

9) Press or ADJUST buttons to make the text appear clean across the screen.

9) Press or ADJUST buttons to make the text appear without flickering.

When adjustment is not possible with Auto Adjust

5) Press the MENU button. The Main Menu will be displayed.

6) Press the SELECT button and select Setup.

7) Press the OK button. The Setup Menu will be displayed.

8) Press the SELECT button and select Clock Phase. (Display fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)

Adjustment

procedure

Example

• The display image may be momentarily disturbed during clock adjustment but this is not a failure.

Vertical

Before adjustment,

streaks

ABCDEFGHIJ

abcdefgABCDEFGabcd

ABCDEFGHIJ

abcdefgABCDEFGabcd

some characters are blurred.

ABC

After adjustment, all characters appear crisp now.

After adjustment, all characters are blurred.

ABCDEFGHIJ

abcdefgABCDEFGabcd

ABCDEFGHIJ

abcdefgABCDEFGabcd

Before adjustment

ABC

After adjustment

Before adjustment

After adjustment

ABC

Page 53

PAL B, G, H / I / D, K SECAM B, G / D, K / K1 NTSC-M

OUTPUT (MONITOR): composite video monitor-output terminal (RCA) OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA) OUTPUT (HEADPHONE): L/R audio monitor- output terminal (Mini-pin)

AV1: composite video input terminal (RCA) AV1: Y PB PR video input terminal (RCA) AV1: L/R audio input terminal (RCA) AV2: composite video input terminal (RCA) AV2: Y/ P

/ PR / video input terminal (RCA) AV2: L/R audio input terminal (RCA) AV3: composite video input terminal (RCA) AV3: S video input terminal AV3: L/R audio input terminal (RCA) AV4: composite video / L/R audio input terminal (RCA) AV5=AV3 AV6=HDMI input terminal Photo input terminal (37/42 only)

ENGLISH

Panel

PRODUCT SPECIFICATIONS

This table shows the specifications when the optional video unit and tuner unit have been inserted.

• The monitor takes at least 30 minutes to attain the status of optimal picture quality.

• RF input : TV only

Ambient conditions

Power supply

Power consumption/at standby

Audio output

(RGB input)

Input terminals

RF Video System

Input signals

Sync signals

Recommended signal

(RF input)

(Video input)

Output Signal

Temperature

Relative humidity

Net dimensions (excluding Speakers/Stand)

Net weight (excluding Speakers/Stand)

Resolution

Display dimensions

Approx. 32 inches (716 (H) x 399 (V) mm, diagonal 820mm)

852 (H) x 1024 (V) pixels

850 (W) x 545 (H) x 110 (D) mm

25.5kg

Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C

Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)

AC100 - 240V, 50/60Hz

245W / <3W

speaker 12W + 12W (6Ω)

RGB1 DVI input terminal (DVI-D) RGB1 audio input terminal (3.5mm Stereo Mini Jack) RGB2 analog RGB input terminal (D-sub 15-pin) RGB2 audio input terminal (3.5mm Stereo Mini Jack)

0.7 V/1.0 Vp-p, analog RGB (Recommended Signal) 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60

H/V separate, TTL level [2KΩ] H/V composite, TTL level [2KΩ] Sync on green, 0.3 Vp-p [75Ω]

44 modes

23 modes

ANT : 75Ω Unbalanced

AV1: PAL, SECAM, NTSC3.58, NTSC4.43 AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60 AV2: PAL, SECAM, NTSC4.43, NTSC3.58 AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60, RGB AV3: PAL, SECAM, NTSC4.43, NTSC3.58, AV4: PAL, SECAM, NTSC4.43, NTSC3.58, AV5=AV3 AV6=HDMI input signal

speaker 12W + 12W (6Ω) speaker 12W + 12W (6Ω),

320W / <3W 380W / <3W

30.5kg 37.0kg

959 (W) x 612 (H) x 118 (D) mm 1050 (W) x 676 (H) x 110 (D) mm

1024 (H) x 1024 (V) pixels 1024(H) x 1024 (V) pixels

Approx. 37 inches (814 (H) x 445 (V) mm, diagonal 930mm)

Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm)

56 57

Page 54

Frame

RGB terminal (D-sub 15-pin connector)

• When different kinds of input signals are simultaneously input to the monitor via a graphics board or the like, the monitor will automatically select the signals in the following priority order:

* Even in the case of the recommended signals shown on the

following page, there may be instances when correct display is not possible. In this case, use H/V separate sync, H/V composite sync.

S-input connector pin specifications

Photo-input connector pin specifications

HDMI connector pin specifications

Pin Input signal

1R (P

R/CR

)

2 G or sync on green (Y)

3B (P

B/CB

)

4 No connection

5 No connection

6 R.GND (P

R/CR

, GND)

7 G.GND (Y, GND)

8 B.GND (P

B/CB

, GND)

9 No connection

10 GND

11 No connection

12 [SDA]

13 H. sync or H/V composite sync

14 V.sync. [V.CLK]

15 [SCL]

( ) : With component input

Input signal

Y-GND

C-GND

GND

Input signal

DM DP

GND

Input signal Pin

Input signal

3 4

5 6 7

8 9

TMDS Data2+

TMDS Data2 Shield

TMDS Data2-

TMDS Data 1+

TMDS Data1 Shield

TMDS Data1-

TMDS Data0+

TMDS Data0 Shield

TMDS Data0TMDS Clock+

12 13

15 16

18 19

TMDS Clock Shield

TMDS Clock-

CEC

Reserved(N.C. on device)

SCL SDA

DDC/CED Ground

+5V Power

Hot Plug Detect

Sync signal type

H/V separate sync.

sync.on Green *

H/V composite sync.

Priority

PRODUCT SPECIFICATIONS (continued)

Signal Input

Page 55

ENGLISH

D-sub

Applicable video signals for input terminal (TV mode)

With Composite Input(AV1~AV5 input) and S-video Input (AV3, AV5 input).

With component input (AV1, AV2 and RGB2-component input).

With HDMI input (AV6 input).

( : Available)

PRODUCT SPECIFICATIONS (continued)

Recommended Signal List

Signal CVBS S-video Component PC STB RGB Component

AV1  Refer to Setup Menu

AV2  Refer to Setup Menu

AV3  Refer to Setup Menu

AV4  Refer to Setup Menu

AV5  Refer to Setup Menu

AV6 

RGB1  Refer to Setup Menu

RGB2 Refer to Setup Menu

Terminal

DVI

HDMI

RemarksRCA/S-video

No.

NTSC4.43 NTSC3.58

PAL

SECAM

525

625

59.94

50.00

15.73

15.63

—

Signal mode

Horizontal

frequency (kHz)

Dot clock

frequency (MHz)

Remarks

Signal Name Resolution

Vertical frequency

(Hz)

Horizontal

frequency (kHz)

Dot clock

frequency (MHz)

Remarks

Vertical frequency

(Hz)

No.

576i

480i

576

480

50.00

59.94

15.63

15.73

—

3 576p 576 50.00 31.26 —

4 480p 480 59.94 31.47 —

5 1080i/50 1080 50.00 28.13 —

6 1080i/60 1080 60.00 33.75 —

7 720p/60 720 60.00 45.00 —

Signal mode

Signal Name Resolution

25.18

27.00

74.25

Horizontal

frequency (kHz)

Dot clock

frequency (MHz)

Remarks

Vertical frequency

(Hz)

No.

VGA

576i

640 x 480

720(1440) x 576

59.94

50.00

31.47

15.63

3 480i 720(1440) x 480 59.94 15.73

4 576p 720 x 576 50.00 31.25

5 480p 720 x 480 59.94 31.47

6 1080i/50 1920 x 1080 50.00 28.13

7 1080i/60 1920 x 1080 60.00 33.75

74.25

EIA-861B

EIA-861B8 720p/60 1280 x 720 60.00 45.00

Signal mode

Signal Name Resolution

Page 56

PRODUCT SPECIFICATIONS (continued)

Recommended Signal List (continued)

With Digital signal input

1 640 X 400 70.08 31.47 25.18  2 640 X 480 59.94 31.47 25.18  3 W-VGA 864 X 480 59.94 31.47 34.24  WVGA type : On 4 640 X 480 72.81 37.86 31.50  5 640 X 480 75.00 37.50 31.50  6 640 X 480 85.01 43.27 36.00  7 800 X 600 56.25 35.16 36.00  8 800 X 600 60.32 37.88 40.00 

9 VESA 800 X 600 72.19 48.08 50.00  10 800 X 600 75.00 46.88 49.50  11 800 X 600 85.06 53.67 56.25  12 1024 X 768 60.00 48.36 65.00  13 1024 X 768 70.07 56.48 75.00  14 1024 X 768 75.03 60.02 78.75  15 480p 720 X 480 59.94 31.47 27.00  EIA-861B 16 576p 720 X 576 50.00 31.25 27.00  EIA-861B 17 720p/60 1280 X 720 60.00 45.00 74.25  EIA-861B 18 1080i/60 1920 X 1080 60.00 33.75 74.25  EIA-861B 19 1080i/50 1920 X 1080 50.00 28.13 74.25  EIA-861B

No.

VGA

Signal Name Resolution

Vertical frequency

(Hz)

Horizontal frequency

(kHz)

Dot clock

frequency

(MHz)

Setup Menu Condition

DVI-PC DVI-STB

Remarks

Signal mode

( : acceptable)

Page 57

ENGLISH

PRODUCT SPECIFICATIONS (continued)

Recommended Signal List (continued)

With Analog signal input (RGB2 input)

No.

Signal Name

VGA

W-VGA

Macintosh

W-XGA

VESA

Resolution

640 X 400

640 X 480

864 X 480

640 X 480

800 X 600

1024 X 768

1152 X 864

1280 X 1024

1600 X 1200

640 X 480

832 X 624

1024 X 768

1152 X 870

1280 X 768

1366 X 768

Vertical frequency

(Hz)

70.08

59.94

72.81

75.00

85.01

56.25

60.32

72.19

75.00

85.06

60.00

70.07

75.03

85.00

75.00

60.02

75.03

85.02

60.00

75.00

85.00

66.67

74.55

74.93

75.06

59.833

69.997

59.876

60.015

Horizontal

frequency (kHz)

31.47

37.86

37.50

43.27

35.16

37.88

48.08

46.88

53.67

48.36

56.48

60.02

68.68

67.50

63.98

79.98

91.15

75.00

93.75

106.25

35.00

49.72

60.24

68.68

47.986

56.137

47.776

47.712

Dot clock

frequency (MHz)

25.18

34.24

31.50

36.00

40.00

50.00

49.50

56.25

65.00

75.00

78.75

94.50

108.00

135.00

157.50

162.00

202.50

229.50

30.24

57.28

80.00

100.00

81.00

94.760

79.50

85.50

Remarks

WVGA type : On

WXGA Mode : 1280x768

WXGA Mode : 1366x768

Signal mode

• The type of video board or connecting cable used may not allow for correct displays adjustment of Horizontal Position, Vertical Position, Horizontal Clock and Clock Phase.

• The monitor may fail to display an animation image correctly when a signal having a vertical frequency of 85Hz or higher is input to it.

• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal

polarities. Note that different signals having all these elements alike may be handled as the same signal.

• Displaying images with more than 512 lines of vertical resolution at Full diplay (compressed display) can result in the interpolation of stripes.

Page 58

NOTE

About the Headphone (Refer to page 44.)

 During PC input (RGB1/RGB2), the audio is not output from the headphone.

 Only with AV1 and AV6 inputs during the 2 picture mode, even though select “B”

from “Audio Menu, Headphone Select,” the audio of A(left picture) is always output

from the headphone.

注

关于耳机(参照44页)

 PC 入力时(RGB1/RGB2)的声音时，耳机没有输出。  只限於AV1和AV6输入2画面表示时，就是选择[声音设定.耳机选择]在“B”耳

机输出的声音将始终是来自A(左画面)。

註

關於耳機(參照44頁)

 PC 入力時(RGB1/RGB2)的聲音時﹐耳機沒有輸出。  只限於AV1和AV6輸入2畫面表示時﹐就是選擇[聲音設定.耳機選擇]在“B”耳

機輸出的聲音將始終是來自A(左畫面)。

お知らせ

ヘッドホンについて（48 ページ参照）

 PC 入力時（RGB1/RGB2）の音声は、ヘッドホンに出力されません。  AV1 と AV6 入力の２画面表示に限り、「音声設定・ヘッドホン選択」にて、“B”を選択

NOTE

About the fixing screw for the Side Input (Refer to page 19.)

 The screw for fixation is attached on the holder

しても、常に A(左画面)からの音声がヘッドホンに出力されます。

with the tape as shown the right figure.

注

关于侧面输入端的固定螺丝钉(参照19页)

按右图所示﹐固定用的螺丝钉有胶带贴在柱子上。



註

Screw

關於側面輸入端的固定螺絲釘(參照19頁)



按右圖所示﹐固定用的螺絲釘有膠帶貼在柱子上。

お知らせ

サイドインプットの固定ネジについて（23 ページ参照）

 右図のように、固定用のネジはホルダーにテープ止めされています。

QT45091