Hitachi 24PC3 User Manual
Model Rotary Hammer
Modèle Marteau rotatif
Modelo Martillo perforador
DH 24PC3
INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS
WARNING
Improper and unsafe use of this power tool can result in death or serious bodily
injury!
This manual contains important information about product safety. Please read
and understand this manual before operating the power tool. Please keep this
manual available for others before they use the power tool.
MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE
AVERTISSEMENT
Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la
mort ou de sérieuses blessures corporelles!
Ce mode d’emploi contient d’importantes informations à propos de la sécurité
de ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser
l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs
avant qu’ils utilisent l’outil motorisé.
MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD
ADVERTENCIA
¡La utilización inapropiada e insegura de esta herramienta eléctrica puede
resultar en lesiones serias o en la muerte!
Este manual contiene información importante sobre la seguridad del producto.
Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde
este manual para que puedan leerlo otras personas antes de que utilicen la
herramienta eléctrica.
DOUBLE INSULATION
DOUBLE ISOLATION
AISLAMIENTO DOBLE
English
IMPORTANT SAFETY INFORMATION
MEANINGS OF SIGNAL WORDS ...... 3
SAFETY ................................................... 4
GENERAL SAFETY RULES ................. 4
SPECIFIC SAFETY RULES AND SYMBOLS
DOUBLE INSULATION FOR SAFER
OPERATION ..................................... 8
FUNCTIONAL DESCRIPTION ................ 9
NAME OF PARTS ................................ 9
SPECIFICATIONS ................................ 9
CONTENTS
Page
..... 3
..... 6
Page
ASSEMBLY AND OPERATION ............ 10
APPLICATIONS ................................. 10
PRIOR TO OPERATION ..................... 10
HOW TO USE .................................... 12
HOW TO USE THE CORE BIT (FOR LIGHT LOAD)
MAINTENANCE AND INSPECTION .... 18
ACCESSORIES ...................................... 20
STANDARD ACCESSORIES ............. 20
OPTIONAL ACCESSORIES ............... 20
PARTS LIST .......................................... 74
... 16
Français
INFORMATIONS IMPORTANTES DE SÉCURITÉ
SIGNIFICATION DES MOTS
D’AVERTISSEMENT ......................... 26
SECURITE ............................................. 27
REGLES GENERALE DE SECURITE
REGLES DE SECURITE SPECIFIQUES ET SYMBOLES
DOUBLE ISOLATION POUR UN
FONCTIONNEMENT PLUS SUR
DESCRIPTION FONCTIONNELLE ........ 33
NOM DES PARTIES .......................... 33
SPECIFICATIONS .............................. 33
Español
INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD
SIGNIFICADO DE LAS PALABRAS DE
SEÑALIZACIÓN ................................. 50
SEGURIDAD ......................................... 51
NORMAS GENERALES DE SEGURIDAD
NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD
AISLAMIENTO DOBLE PARA OFRECER UNA
OPERACIÓN MÁS SEGURA
DESCRIPCIÓN FUNCIONAL ................ 57
NOMENCLATURA ............................. 57
ESPECIFICACIONES .......................... 57
TABLE DES MATIERES
Page
... 26
....... 27
... 29
........ 32
ASSEMBLAGE ET FONCTIONNEMENT ....
APPLICATIONS ................................. 34
AVANT L’UTILISATION .................... 34
UTILISATION ..................................... 36
COMMENT UTILISER LA COURONNE (POUR
ENTRETIEN ET INSPECTION ............... 42
ACCESSOIRES ...................................... 44
ACCESSOIRES STANDARD ............. 44
ACCESSOIRES SUR OPTION ........... 44
LISTA DES PIÈCES ............................... 74
ÍNDICE
Página
.. 50
... 51
..... 53
................... 56
Página
MONTAJE Y OPERACIÓN ................... 58
APLICACIONES ................................. 58
ANTES DE LA OPERACIÓN .............. 58
COMO SE USA .................................. 60
MODO DE USAR LA BARRENA TUBULAR
MANTENIMIENTO E INSPECCIÓN ..... 66
ACCESORIOS ....................................... 68
ACCESORIOS ESTÁNDAR ............... 68
ACCESORIOS OPCIONALES ............ 68
LISTA DE PIEZAS ................................. 74
UNE CHARGE LEGERE)
(PARA CARGAS LIGERAS)
.........................
................ 64
Page
34
40
English
IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating
instructions in the Instruction Manual before operating or maintaining this power
tool.
Most accidents that result from power tool operation and maintenance are caused
by the failure to observe basic safety rules or precautions. An accident can often be
avoided by recognizing a potentially hazardous situation before it occurs, and by
observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction
Manual and in the sections which contain the operation and maintenance
instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are
identified by WARNINGS on the power tool and in this Instruction Manual.
NEVER use this power tool in a manner that has not been specifically recommended
by HITACHI.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result
in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may
result in minor or moderate injury, or may cause machine damage.
NOTE emphasizes essential information.
3
English
SAFETY
GENERAL SAFETY RULES
WARNING: Read and understand all instructions.
Failure to follow all instructions listed below, may result in electric
shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
1. Work Area
(1) Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
(2) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite the dust of fumes.
(3) Keep bystanders children, and visitors away while operating a power
tool. Distractions can cause you to lose control.
2. Electrical Safety
(1) Double Insulated tools are equipped with a polarized plug (one blade is
wider than the other.) This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a polarized outlet.
Do not change the plug in any way. Double Insulation
need for the three wire grounded power cord and grounded power supply
system.
(2) Avoid body contact with grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your
body is grounded.
(3) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
(4) Do not abuse the cord. Never use the cord to carry the tools or pull the
plug from a receptacle. Keep cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
(5) When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These cords are rated for outdoor use and reduce
the risk of electric shock.
3. Personal Safety
(1) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use tool while tired or under the influence
of drugs, alcohol, or medication. A moment of inattention while operating
power tools may result in serious personal injury.
(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing and gloves away from moving parts. Loose
4
clothes, jewelry, or long hair can be caught in moving parts.
eliminates the
(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying
tools with your finger on the switch or plugging in tools that have the switch
on invites accidents.
(4) Remove adjusting keys or wrenches before turning the tool on. A wrench
or a key that is left attached to a rotating part of the tool may result in
personal injury.
(5) Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the tool in unexpected
situations.
(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
4. Tool Use and Care
(1) Use clamps or other practical way to secure and support the workpiece
to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
(2) Do not force tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be
controlled with the switch is dangerous and must be repaired.
(4) Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing the tool. Such preventive safety measures
reduce the risk of starting the tool accidentally.
(5) Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools, with sharp cutting edges are less likely to bind and are
easier to control.
(7) Check for misalignment or binding of moving parts, breakage of parts,
and any other condition that may affect the tool's operation. If damaged,
have the tool serviced before using. Many accidents are caused by poorly
maintained tools.
(8) Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one tool, may become
hazardous when used with another tool.
5. Service
(1) Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of
injury.
(2) When servicing a tool, use only identical replacement parts. Follow
instructions in the Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance Instruction may create
a risk of electric shock or injury.
English
5
English
SPECIFIC SAFETY RULES AND SYMBOLS
1. Hold tools by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the tool “live” and shock the
operator.
2. ALWAYS wear ear protectors when using the tool for extended periods.
Prolonged exposure to high intensity noise can cause hearing
loss.
3. NEVER touch the tool bit with bare hands after operation.
4. NEVER wear gloves made from materials likely to roll up such as cotton, wool,
cloth or string, etc.
5. ALWAYS attach the side handle and securely grip the Rotary Hammer.
6. NEVER touch moving parts.
NEVER place your hands, fingers or other body parts near the tool’s movink
parts.
7. NEVER operate without all guards in place.
NEVER operate this tool without all guards or safety features in place and in
proper working order. If maintenance or servicing requires the removal of a
guard or safety feature, be sure to replace the guard or safety feature before
resuming operation of the tool.
8. Use right tool.
Don’t force small tool or attachment to do the job of a heavy-duty tool.
Don’t use tool for purpose not intended —for example— don’t use circular saw
for cutting tree limbs or logs.
9. NEVER use a power tool for applications other than those specified.
NEVER use a power tool for applications other than those specified in the
Instruction Manual.
10. Handle tool correctly.
Operate the tool according to the instructions provided herein. Do not drop or
throw the tool. NEVER allow the tool to be operated by children, individuals
unfamiliar with its operation or unauthorized personnel.
11. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted. Check their condition
periodically.
12. Do not use power tools if the plastic housing or handle is cracked.
Cracks in the tool’s housing or handle can lead to electric shock. Such tools
should not be used until repaired.
13. Blades and accessories must be securely mounted to the tool.
Prevent potential injuries to yourself or others. Blades, cutting implements and
accessories which have been mounted to the tool should be secure and tight.
6
English
14. Keep motor air vent clean.
The tool’s motor air vent must be kept clean so that air can freely flow at all
times. Check for dust build-up frequently.
15.Operate power tools at the rated voltage.
Operate the power tool at voltages specified on its nameplate.
If using the power tool at a higher voltage than the rated voltage, it will result in
abnormally fast motor revolution and may damage the unit and the motor may
burn out.
16. NEVER use a tool which is defective or operating abnormally.
If the tool appears to be operating unusually, making strange noises, or otherwise
appears defective, stop using it immediately and arrange for repairs by a Hitachi
authorized service center.
17. NEVER leave tool running unattended. Turn power off.
Don’t leave tool until it comes to a complete stop.
18. Carefully handle power tools.
Should a power tool be dropped or struck against hard materials inadvertently,
it may be deformed, cracked, or damaged.
19. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol
may damage and crack plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry
thoroughly.
20. ALWAYS wear eye protection that meets the requirement of the latest revision
of ANSI Standard Z87.1.
21. ALWAYS be careful with buried object such as an underground wiring.
Touching live wiring or electric cable with this tool may result in electric shock.
Confirm before use whether hidden objects are present, such as electric cables
within the wall, floor or ceiling.
22. Definitions for symbols used on this tool
V ............volts
Hz .......... hertz
A ............ amperes
no .......... no load speed
W ........... watt
........... Class II Construction
---/min ... revolutions per minute
.......... Alternating current
7
English
DOUBLE INSULATION FOR SAFER OPERATION
To ensure safer operation of this power tool, HITACHI has adopted a double insulation
design. “Double insulation” means that two physically separated insulation systems
have been used to insulate the electrically conductive materials connected to the
power supply from the outer frame handled by the operator. Therefore, either the
symbol “
nameplate.
Although this system has no external grounding, you must still follow the normal
electrical safety precautions given in this Instruction Manual, including not using
the power tool in wet environments.
To keep the double insulation system effective, follow these precautions:
䡬 Only Hitachi Authorized Service Center should disassemble or assemble this
power tool, and only genuine HITACHI replacement parts should be installed.
䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy
water, and dry thoroughly.
Never use solvents, gasoline or thinners on plastic components; otherwise the
plastic may dissolve.
” or the words “Double insulation” appear on the power tool or on the
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO
OTHER USERS
AND
OWNERS OF THIS TOOL!
8
FUNCTIONAL DESCRIPTION
NOTE:
The information contained in this Instruction Manual is designed to assist you in
the safe operation and maintenance of the power tool.
NEVER operate, or attempt any maintenance on the tool unless you have first
read and understood all safety instructions contained in this manual.
Some illustrations in this Instruction Manual may show details or attachments
that differ from those on your own power tool.
NAME OF PARTS
English
Depth gauge
Drill bit
Front cap
Grip
Side handle
Push button
Nameplate
Housing
Stopper
Push button
Handle
Change lever
Switch
Fig. 1
SPECIFICATIONS
Motor Single-Phase, Series Commutator Motor
Power Source Single-Phase, 120V 60Hz
Current 7.0A
Capacity Concrete: 1/8" ~ 15/16" (3.4mm ~ 24mm)
Steel: 1/2" (13mm)
Wood: 1-1/4" (32mm)
No-Load Speed 0 – 1,150/min.
Full-load Impact Rate 0 – 4,600/min.
Weight 5.3 lbs (2.4 kg)
9
English
ASSEMBLY AND OPERATION
APPLICATIONS
Rotation and hammering function
䡬 Drilling anchor holes
䡬 Drilling holes in concrete
䡬 Drilling holes in tile
Rotation only function
䡬 Drilling in steel or wood (with optional accessories).
䡬 Tightening machine screws, wood screws (with optional accessories).
Hammering only function
䡬 Light-duty chiselling of concrete, groove digging and edging.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate.
2. Power switch
Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while the switch is in the ON position, the power tool will start operating
immediately and can cause serious injury.
3. Extension cord
When the work area is far away from the power source, use an extension cord of
sufficient thickness and rated capacity. The extension cord should be kept as
short as practicable.
WARNING:
Damaged cord must be replaced or repaired.
4. Check the receptacle
If the receptacle only loosely accepts the plug, the receptacle must be repaired.
Contact a licensed electrician to make appropriate repairs.
If such a faulty receptacle is used, it may cause overheating, resulting in a serious hazard.
10
5. Confirming condition of the environment:
Confirm that the work site is placed under appropriate conditions conforming to
prescribed precautions.
6. Mounting the drill bit (Fig. 2)
CAUTION:
Part of SDS-plus shank
Front cap
Grip
To prevent accidents, make sure to turn
the switch off and disconnect the plug
from the receptacle.
NOTE:
When using tools such as bull points,
drill bits, etc., make sure to use the
Drill bit
Fig. 2
genuine parts designated by our
company.
(1) Clean the shank portion of the drill bit.
(2) Insert the drill bit in a twisting manner
into the tool holder until it latches
itself. (Fig. 2)
Grip
(3) Check the latching by pulling on the
drill bit.
(4) To remove the drill bit, fully pull the grip
Fig. 3
in the direction of the arrow and pull
out the drill bit. (Fig. 3)
7. Installation of dust cup or dust
collector (B) (Optional accessories)
Dust cup
(Fig. 4, Fig. 5)
When using a rotary hammer for up-
ward drilling operations attach a dust
cup or dust collector (B) to collect dust
or particles for easy operation.
䡬 Installing the dust cup
Use the dust cup by attaching to the
drill bit a shown in Fig. 4.
When using a bit which has big
diameter, enlarge the center hole of the
dust cup with this rotary hammer.
䡬 Installing dust collector (B)
When using dust collector (B), insert
dust collector (B) from the tip of the bit
by aligning it to the groove on the grip
(Fig. 5)
Dust collector (B)
Fig. 4
English
Fig. 5
11
English
CAUTION:
䡬 The dust cup and dust collector (B) are for exclusive use of concrete drilling
work. Do not use them for wood or metal drilling work.
䡬 Insert dust collector (B) completely into the chuck part of the main unit.
䡬 When turning the rotary hammer on while dust collector (B) is detached from a
concrete surface, dust collector (B) will rotate together with the drill bit. Make
sure to turn on the switch after pressing dust cup on the concrete surface. (When
using dust collector (B) attached to a drill bit that has more than 7-15/32" (190
mm) of overall length, dust collector (B) cannot touch the concrete surface and
will rotate. Therefore please use dust collector (B) by attaching to drill bits which
have 6-17/32" (166 mm), 6-19/64" (160 mm) and 4-21/64" (110 mm) overall length.
䡬 Dump particles after every two or three holes when drilling.
䡬 Please replace the drill bit after removing dust collector (B).
8. Selecting the driver bit
Screw heads or bits will be damaged unless a bit appropriate for the screw
diameter is employed to drive in the screws.
9. Confirm the direction of bit rotation
(Fig. 6)
The bit rotates clockwise (viewed from
the rear side) by pushing the R-side of
the push button. The L-side of the push
button is pushed to turn the bit
counterclockwise.
R
L
Fig. 6
L
L
R
Push
button
R
HOW TO USE
CAUTION:
䡬 To prevent accidents, make sure to turn the switch off and disconnect the plug
from the receptacle when the drill pits and other various parts are installed or
removed. The power switch should also be turned off during a work break and
after work.
1. Switch operation
䡬 The rotation speed of the drill bit can be controlled steplessly by varying the
amount that the trigger switch is pulled. Speed is low when the trigger switch is
pulled slightly and increases as the switch is pulled more. To turn the switch
OFF, release the trigger switch to its original position. However, the switch
trigger can only be pulled in halfway during reverse and rotates at half the speed
of forward operation.
䡬 Pulling the trigger and pushing the stopper, it keeps the switched-on condition
which is convenient for continuous running. When switching off, the stopper
can be disconnected by pulling the trigger again. The switch stopper is unusable
during reverse.
12
English
Change lever
2. Rotation + Hammering
This rotary hammer can be set to
rotation and hammering mode by
pressing the push button and turning
the change lever to
(1) Mount the drill bit.
(2) Pull the trigger switch after applying the
drill bit tip to the drilling position (Fig. 8)
(3) Pushing the rotary hammer forcibly is
not necessary at all. Pushing slightly so
that drill dust comes out gradually is
just sufficient.
CAUTION:
䡬 When the drill bit touches an iron reinforcing rod, the bit will stop immediately
and the rotary hammer will react to revolve. Therefore please grip the side
handle and handle tightly as shown in Fig. 8.
3. Rotation only
This rotary hammer can be set to
rotation only mode by pressing the
push button and turning the change
lever to
To drill a wood or metal material using
the separately sold drill chuck and chuck
adaptor, proceed as follows. Installing
drill chuck and chuck adaptor (Fig. 10):
(1) Attach the drill chuck to the chuck
adaptor.
(2) The part of the SDS-plus shank is the
same as the drill bit. Therefore, refer to
the item of “Mounting the drill bit” for
attaching it.
mark. (Fig. 9)
mark. (Fig. 7)
Drill chuck
Chuck adaptor
Push
button
Fig. 7
Fig. 8
Push
button
Change lever
Fig. 9
Front cap
Part of SDS-plus
shank
Grip
CAUTION:
Fig. 10
䡬 Application of force more than necessary will not only reducing drilling
efficiency at all, but will deteriorate the tip edge of the drill bit and reduce the
service life of the rotary hammer in addition.
13
English
䡬 Drill bit may snap off while withdrawing the rotary hammer from the drilled
hole. For withdrawing, it is important to use a pushing motion.
䡬 Do not attempt to drill anchor holes or holes in concrete with the main unit in
the rotation only function.
䡬 Do not attempt to use the rotary hammer in the rotation and striking function
with the drill chuck and chuck adaptor attached. This would seriously shorten
the service life of every components of the machine.
4. When driving machine screws
(Fig. 11)
Bit
Socket
First, insert the bit into the socket in the
end of chuck adaptor (D).
Next, mount chuck adaptor (D) on the
main unit using procedures described
in 5 (1), (2), (3), put the tip of the bit in
Chuck adaptor (D)
Front cap
Grip
the slots in the head of the screw, grasp
the main unit and tighten the screw.
Fig. 11
CAUTION:
䡬 Exercise care not to excessively prolong driving time, otherwise, the screws
may be damaged by excessive force.
䡬 Apply the rotary hammer perpendicularly to the screw head when driving a
screw; otherwise, the screw head or bit will be damaged, or driving force will
not be fully transferred to the screw.
䡬 Do not attempt to use the rotary hammer in the rotation and striking function
with chuck adaptor (D) and bit attached.
5. When driving wood screws (Fig. 11)
(1) Selecting a suitable driver bit
Employ phillips screws, if possible, since the driver bit easily slips off the heads
of slotted-head screws.
(2) Driving in wood screws
䡬 Prior to driving in wood screws, make pilot holes suitable for them in the wooden
board. Apply the bit to the screw head grooves and gently drive the screws into
the holes.
䡬 After rotating the rotary hammer at low speed for a while until a wood screw in
partly driven into the wood, squeeze the trigger more strongly to obtain the
optimum driving force.
CAUTION:
䡬 Exercise care in preparing a pilot hole suitable for the wood screw taking the
hardness of the wood into consideration. Should the hole be excessively small
or shallow, requiring much power to drive the screw into it, the thread of the
wood screw may sometimes be damaged.
14
English
6. Hammering only
This rotary hammer can be set to
hammering only mode by pressing the
push button and turning the change
lever to
mark. (Fig. 12)
(1) Mount the bull point or cold chisel.
(2) Press the push button and set the
change lever to middle of
mark and
mark. (Fig. 13)
The rotation is released, turn the grip
and adjust the cold chisel to desired
position. (Fig. 14)
(3) Tu rn the change lever to
mark.
(Fig. 12)
Then bull point or cold chisel is locked.
7. Using depth gauge (Fig. 15)
(1) Loosen the knob on the side handle,
and insert the depth gauge into the
mounting hole on the side handle.
(2) Adjust the depth gauge position ac-
cording to the depth of the hole and
tighten the knob bolt securely.
8. How to use the drill bit (taper shank)
and the taper shank adaptor.
(1) Mount the taper shank adaptor to the
rotary hammer. (Fig. 16)
(2) Mount the drill bit (taper shank) to the
taper shank adaptor. (Fig. 16)
(3) Turn the switch ON, and drill a hole in
prescribed depth.
Grip
Push
button
Fig. 12
Push
button
Fig. 13
Fig. 14
Change lever
Change lever
Knob on side
handle
Mounting hole
Fig. 15
Depth gauge
Drill bit
Taper shank
adaptor
Grip
Front cap
Fig. 16
15
English
(4) To remove the drill bit (taper shank),
insert the cotter into the slot of the taper
shank adaptor and strike the head of
the cotter with a hammer supporting
Cotter
Taper shank adaptor
on the rests. (Fig. 17)
Rests
Fig. 17
HOW TO USE THE CORE BIT (FOR LIGHT LOAD)
When boring penetrating large hole use the core bit (for light load). At that time use
with the center pin and the core bit shank provided as optional accessories.
1. Mounting
CAUTION:
䡬 Be sure to turn power OFF and discon-
nect the plug from the receptacle.
(1) Mount the core bit to the core bit shank.
(Fig. 18)
Lubricate the thread of the core bit
shank to facilitate disassembly.
(2) Mount the core bit shank to the rotary
hammer. (Fig. 19)
(3) Insert the center pin into the guide plate
until it stops.
16
Core bit
Thread
Core bit shank
Fig. 18
Fig. 19
English
(4) Engage the guide plate with the core
bit, and turn the guide plate to left or
right so that it does not fall even if it
faces downward. (Fig. 20)
Center pin
Core bit
Guide plate
Core bit tip
2. How to bore (Fig. 21)
(1) Connect the plug to the power source.
(2) A spring is installed in the center pin.
Push it lightly to the wall or the floor
Fig. 20
straight. Connect all over the surface
of the core bit tip and start operating.
(3) When boring about 3/16" (5 mm) in
depth the position of the hole will
establish. Bore after that removing the
center pin and the guide plate from core
bit.
Fig. 21
(4) Application of excessive force will not only expedite the work, but will deteriorate
the tip edge of the drill bit, resulting in reduced service life of the rotary hammer.
CAUTION:
䡬 When removing the center pin and the guide plate, turn OFF the switch and
disconnect the plug form the receptacle.
3. Dismounting. (Fig. 22)
Remove the core bit shank from the
rotary hammer and strike the head of
the core bit shank strongly two or three
times with the hammer holding the
core bit, then the thread becomes loose
and the core bit can be removed.
Core bit shank
Fig. 22
17
English
MAINTENANCE AND INSPECTION
WARNING: Be sure to switch power OFF and disconnect the plug from the
receptacle during maintenance and inspection.
1. Inspecting the drill bits
Since use of a dull tool will cause motor malfunctioning and degraded efficiency,
replace the drill bit with a new one or resharpening without delay when abrasion
is noted.
2. Inspecting the screws
Regularly inspect all screws and ensure that they are properly tightened. Should
any of the screws be loosened, retighten them immediately.
WARNING: Using this rotary hammer with loosen screws is extremely
dangerous.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power tool. Exercise due care
to ensure the winding does not become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes
For your continued safety and electrical shock protection, carbon brush inspection
and replacement on this tool should ONLY be performed by a Hitachi Authorized
Service Center.
5. How to replace grease
Low viscosity grease is applied to this rotary hammer so that it can be used for
a long period without replacing the grease. Please contact the nearest service
center for grease replacement when any grease is leaking from loosened screw.
Further use of the rotary hammer despite the grease shortage causes seizure to
reduce the service life.
CAUTION: A specific grease is used with this machine, therefore, the normal
performance of the machine may be badly affected by use of other
grease. Please be sure to let one of our service agents undertake
replacement of the grease.
6. Service and repairs
All quality power tools will eventually require servicing or replacement of parts
because of wear from normal use. To assure that only authorized replacement
parts will be used, all service and repairs must be performed by a Hitachi
Authorized Service Center, ONLY.
18
7. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION: Repair, modification and inspection of Hitachi Power Tools must be
carried out by a Hitachi Authorized Service Center.
This Parts List will be helpful if presented with the tool to the Hitachi
Authorized Service Center when requesting repair or other
maintenance. In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each country must
be observed.
MODIFICATIONS:
Hitachi Power Tools are constantly being improved and modified to incorporate
the latest technological advancements.
Accordingly, some parts (i.e. code numbers and/or design) may be changed
without prior notice.
English
19
English
ACCESSORIES
WARNING: ALWAYS use Only authorized HITACHI replacement parts and
accessories. NEVER use replacement parts or accessories which
are not intended for use with this tool. Contact HITACHI if you
are not sure whether it is safe to use a particular replacement
part or accessory with your tool.
The use of any other attachment or accessory can be dangerous
and could cause injury or mechanical damage.
NOTE:
Accessories are subject to change without any obligation on the part of the HITACHI.
STANDARD ACCESSORIES
(1) Plastic Case (Code No. 324555) .............................................................................. 1
(2) Side Handle (Code No. 324548) ..............................................................................1
(3) Depth Gauge (Code No. 310331) ............................................................................1
OPTIONAL ACCESSORIES...........sold separately
1. Drilling anchor holes (Rotation + Hammering)
䡬 Drill Bit (Slender shaft)
(1) Drill Bit (Slender
Shaft)
(1) Drill Bit (Slender Shaft)
Outer diameter Effective Length Overall Length Code No. Code No.
1/8" 1-25/32" 3-35/64"
(3.4 mm) (45 mm) (90 mm)
9/64" 1-25/32" 3-35/64"
(3.5 mm) (45 mm) (90 mm)
20
(2) Adaptor for slender shaft
(SDS-plus shank)
(2) Adaptor for
Slender Shaft
306369
306370
306368
䡬 Drill Bit (Taper shank) and taper shank adaptor
English
(1) Drill Bit (Taper Shank)
External dia. Code No.
7/16"
(11 mm)
1/2"
(12.3 mm)
1/2"
(12.7 mm)
9/16"
(14.3 mm)
9/16"
(14.5 mm)
11/16"
(17.5 mm)
7/8"
(21.5 mm)
944460
944461
993038
944462
944500
944463
944464
(2) Taper Shank Adaptor
(SDS-plus shank)
Cotter (Code No. 944477)
Taper mode Code No. Applicable drill bit
7/16" (11 mm)
1/2" (12.3 mm)
1/2" (12.7 mm)
9/16" (14.3 mm)
9/16" (14.5 mm)
11/16" (17.5 mm)
Morse taper
(No. 1)
Morse taper
(No. 2)
A-taper 303619
B-taper 303620
303617
303618 7/8" (21.5 mm)
Drill bit
(Taper
shank)
Drill bit
(Taper
shank)
Taper shank adaptor formed Ataper or B-taper is provided as an
optional accessory, but drill bit for
it is not provided.
䡬 1/2" (13 mm) Hammer Drill chuck and Chuck wrench
For drilling operations when using a straight shank bit for impact drilling with a
rotary hammer
Impact Drill
Application
Straight shank Bit
Name Code No.
1/2" (13 mm) Hammer Drill Chuck 303332
Chuck wrench 303334
Rubber Cap 303335
1/2" (13 mm) Hammer Drill
Chuck (SDS-plus shank)
(includes Chuck wrench)
Chuck wrench
21
English
2. Knock-in anchor (Rotation + Hammering)
Anchor Setter (for anchor setting)
(SDS-plus shank)
<Outer wedge type with the female screw>
Anchor size
Overall Length
Code No. 302976 302975 303621 302974
<Inner wedge type with the headless screw>
Anchor size
Overall Length
Code No. 302979 302978 303622 302977
W 1/4" W 5/16" W 3/8"
(6.3 mm) (8 mm) (9.5 mm)
10-1/4" 10-1/4" 6-1/4" 10-1/4"
(260 mm) (260 mm) (160 mm) (260 mm)
W 1/4" W 5/16" W 3/8"
(6.3 mm) (8 mm) (9.5 mm)
10-1/4" 10-1/4" 6-1/4" 10-1/4"
(260 mm) (260 mm) (160 mm) (260 mm)
22
Anchor setting adaptor
(for manual hammer)
<Outer wedge type with
the female screw>
Anchor size Code No.
W1/4"
(6.3 mm)
W5/16"
(8 mm)
W3/8"
(9.5 mm)
W1/2"
(12.7 mm)
W5/8"
(15.9 mm)
971794
971795
971796
971797
971798
<Inner wedge type with
the headless screw>
Anchor size Code No.
W1/4"
(6.3 mm)
W5/16"
(8 mm)
W3/8"
(9.5 mm)
W1/2"
(12.7 mm)
W5/8"
(15.9 mm)
971799
971800
971801
971802
971803
3. Large hole boring (Rotation + Hammering)
English
Guide
Plate
Center
Center pin Core Bit
Code No. Code No. Code No.
pin
––
(A) 982684 1-3/8" (35 mm) 982675 12"
(B) 982685 (B)
Core bit (outer diameter) Core bit shank
1"(25 mm) 982672 Overall length
1-1/8" (29 mm) 982673 4-1/8" 303625
(A) 1-1/4" (32 mm) 982674 (A) (105 mm)
1-1/2" (38 mm) 982676 (300 mm)
1-3/4" (45 mm) 982677
2" (50 mm) 982678 (300 mm)
Core bit Shank
(SDS-plus shank)
(B)
Guide plate
Core bit
(outer diameter)
1-1/4" (32 mm)
1-3/8" (35 mm)
1-1/2" (38 mm)
Code No.
982686
982687
982688
Core bit
(outer diameter)
1-3/4" (45 mm)
2" (50 mm)
Code No.
982689
982690
4. Demolishing operation (Hammering only)
Bull point (Round type) (SDS-plus shank)
Code No. 303046
12"
303626
303627
Bull point (Square type) (SDS-plus shank)
Code No. 316656
23
Loading...