How it Works
Hitachi
Loading...
20VR2W
User Manual
40 pgs505.6 Kb0

Hitachi 20VR2W, 20VR2B User Manual

Important
1HITACHI
TV/VCR Combination
20VR2B/W
OPERATING GUIDE
Table of Contents
Important.............................................................................................................................3
Getting Started.....................................................................................................................6
Basic Antenna Connection..........................................................................................6
Cable Connections.......................................................................................................7
To Playback......................................................................................................................... 8
Description of Controls.......................................................................................................9
Rear................................................................................................................................9
Front................................................................................................................................9
TV/VCR Unified Remote Control .............................................................................10
On Screen Indications .......................................................................................................12
VCR Status Display....................................................................................................12
OSD Menu Screen.....................................................................................................12
Closed Caption System .....................................................................................................13
Clock Adjustment..............................................................................................................15
To Set the Clock.........................................................................................................15
To Make Corrections..................................................................................................15
To Display the Date and Time..................................................................................16
To Reset the Clock..................................................................................................... 16
Channel Memory...............................................................................................................17
Automatic Setting.......................................................................................................18
Using the Add/ Delete button....................................................................................18
One Press Channel Search......................................................................................18
Using the 100 key.......................................................................................................18
To Watch TV.....................................................................................................................19
Audio Mute...................................................................................................................19
Sleep Timer.................................................................................................................19
Video Adjust Menu.....................................................................................................19
How to Adjust..............................................................................................................20
Special Playback Features.................................................................................................21
To Rapidly Locate a Particular Segment................................................................21
Intelligent Search........................................................................................................21
To View a Double Speed Playback Picture............................................................21
To View an Instant Search........................................................................................21
To View a Still Picture (During Playback)...............................................................21
To Advance a Still Picture.........................................................................................22
To View a Slow Motion Picture.................................................................................22
Auto Operation Functions......................................................................................... 22
Digital Auto Tracking..................................................................................................22
Tracking Control.........................................................................................................23
To Check a Channel from Playback........................................................................23
Blank Tape Indication................................................................................................23
To Record..........................................................................................................................24
One Touch Recording .......................................................................................................25
A. Instant OTR............................................................................................................26
B. Standby OTR..........................................................................................................26
Timer Recording ...............................................................................................................28
1
Important
Daily Recording...........................................................................................................29
Weekly Recording ......................................................................................................30
To Check or Re-Enter Timer Programs..................................................................30
To Clear Programs.....................................................................................................31
To Stop a Timer Recording in Progress .................................................................31
Re-Recording (Tape Duplication).....................................................................................32
Tape Operation..................................................................................................................33
Rec End Search..........................................................................................................33
Time Search................................................................................................................33
Auto Play with Repeat Function...............................................................................34
Time Counter Control.................................................................................................34
Types of Video Cassettes.........................................................................................35
Erase Protection (Record Tab).................................................................................36
Cleaning Care for Video Heads...............................................................................36
Helpful Notes On Operations............................................................................................37
Before Requesting Service................................................................................................38
Accessories.................................................................................................................39
Specifications....................................................................................................................40
2
Important
Important
We are pleased to introduce you to one of the most sophisticated products available today. Please take time to fill out the information requested on the right. The serial number is on the tag located on the back of your TV/VCR Combination. Be sure to retain this manual as your convenient TV/VCR Combination information source.
Date of Purchase _ Dealer Purchased From _ Dealer Address _ Dealer Phone No _ Model No. 20VR2 Serial No. _
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the TV/VCR Combination enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the TV/VCR Combination.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS TV/VCR COMBINATION TO RAIN OR MOISTURE.
There are no user serviceable parts inside the TV/VCR Combination.
 Never remove the back cover of the TV/VCR Combination, as this can expose you to a very high voltage and other hazards.  If the TV/VCR Combination does not operate properly, unplug the set and call your dealer or service shop.
WARNING: POWER SOURCE
 This TV/VCR Combination operates only on AC 120 volts 60 Hz.  To prevent fire or shock hazard, connect this TV/VCR Combination to 120 V AC 60 Hz (house current) ONLY. Never connect the TV/VCR Combination to 50 Hz or DIRECT CURRENT POWER SOURCES.  This TV/VCR Combination is equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the receptacle only one way. If you are unable to insert the plug fully into the receptacle, try reversing the plug. If the plug should still fail to fit, contact a local electrician.  To prevent shock hazard do not use this polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to
3
Important
prevent blade exposure.  If the power cord or plug is damaged or frayed, unplug the TV/VCR Combination from the receptacle and refer servicing to qualified service personnel.  To prevent fire or shock hazard, do not overload receptacle and extension cords.
POLARIZED PLUG
NO GOOD
INSTALLATION
ANTENNA Unless your TV/VCR Combination is connected to a cable TV/VCR Combination system or to a centralized antenna system, a good outdoor color TV/VCR Combination antenna is recommended for the best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, the indoor antenna may be sufficient.
LOCATION Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the TV/VCR Combination. To prevent damaging the TV/VCR Combination, do not leave the set in a place where the temperature becomes too hot. For example, exposed to direct sunlight or near a heating device, etc.  VIEWING
4
Important
cause damage to the TV/VCR Combination. If something gets into the TV/VCR Combination, immediately unplug the TV/VCR Combination and have it cleaned and inspected.
5
Getting Started
Getting Started
Basic Antenna Connection
(A) Combination VHF/ UHF System
6
Getting Started
Cable Connections
A) Without a Converter / Descrambler Box
Use this connection if your cable system connects directly to your TV/VCR Combination without a converter box.
With this connection, you can:
1) use your TV/VCR Combination remote control to select channels.
2) program one or more unscrambled channels for timer recording.
NOTE:
 You can use the TV/VCR Combination Channel Up/ Down keys to select the desired channel.  You cannot record or view scrambled channels with this connection.
Note to CATV System Installer
This reminder is provided to call the CATV (Cable TV) System Installers attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
B) With a Converter/ Descrambler Box
If your cable service supplies you with a converter box, you can use the basic connection shown here.
With this connection, you can record and view any channel including scrambled channels. However, channel selection must be made at the cable company converter box. This means that channels cannot be changed using the TV/VCR Combination remote control. Timer recording is limited to one channel at a time, and you cannot view another channel other than the one you are recording.
To Record and View a Scrambled / Unscrambled Channel
1. Set the TV/VCR Combination channel selector to the output channel of the cable converter box (e.g. CH3).
2. Select the channel to be recorded at the cable converter box.
Note: Refer to page 11 for instructions on setting tuner to the cable TV mode.
FCC WARNING: Any unauthorized changes or modifications to this equipment would void the user's authority to operate.
7
To Playback
To Playback
Preparation:
 Make sure that the steps in "Getting Started" on page 3 have been completed.
Location of Controls
1 Insert a cassette.
The power will come on automatically. If the record tab (p. 24) is removed, playback will start automatically. In this case, skip step 2. If a cassette is already in the TV/VCR Combination, just press the power button ON.
2 Press the Play button.
Playback starts.
3 Press the Stop button.
Playback stops.
8
Description of Controls
Description of Controls
Rear
Diagram of Rear Jacks
VHF/UHF Antenna Input Terminal In from the Antenna or Cable.  Video Input Connector For video input connection from another VCR or a portable video camera power supply.  Audio Input Connector For connection from a portable video camera power supply, another VCR or the output connector of another audio source.
Front
Diagram of Front Controls
Record Indicator This indicator lights during recording.  Rec Button Press this button and Play button at the same time to begin a recording.  Play / X2 Button To play back a tape. In SLP playback, press this button once more for rapid search at twice the normal speed.  Fast Forward / Search Button To rapidly advance the tape. Also, during playback press this button to view a rapid forward search.  Repeat Indicator This indicator lights when the repeat function is selected.  Timer Indicator This indicator lights when the TV/VCR Combination is set for unattended recording.  Rewind / Search Button To rewind tapes. Also, during playback press this button to view the picture in rapid reverse.  Cassette Compartment Where the video cassette is inserted.  Stop / Eject Button To stop the tape. To remove a cassette in the stop mode.  Volume Up / Down Buttons Press either the Volume Up or Down button to change the sound level from the built-in speaker.
Channel Up/ Down Keys
Used to select the desired TV/VCR Combination tuner channel. Can also be used to clear or reset items in a displayed program.
Wireless Remote Sensor
Receives the signal from the wireless remote control.
Power Button
To turn the monitor on and off.
Power Indicator
This indicator flashes when an operation button is pressed on the remote control.
9
Description of Controls
TV/VCR Unified Remote Control
Most of the TV/VCR Combination functions are conveniently controlled with your wireless remote control. For battery replacement see the back cover.
Picture of Remote Control
Eject Button To remove a cassette in the stop mode.  Power button To turn the monitor on and off.  Repeat Button Used to repeat playback of the continuously recorded portion of a tape.  Sleep Timer Button Each press of this button advances the automatic off timer by 30 minutes (maximum is 90 minutes).  Monitor Button During Playback, press this button to display the TV channel currently tuned. Press again to resume playback from still mode.  Input Button Press this button for the desired input to the TV/VCR Combination. Tuner: For regular TV or Cable TV recording. Line: For re-record ing or camera recording. "TUNER" or "LINE" will appear automatically for a few seconds on the TV screen when this button is pressed.  Prog Button Used for setting the clock, channel memory, closed caption and timer recording.
Counter Memory Button Turns the memory stop feature on and off.  Clear / Reset Button Clear Button Press this button to clear the setting for the displayed program contents. Reset Button Resets the time counter when it is displayed.  Recall Button Press this button to display or clear the time counter, date, time, function, and channel number.
Standby Button
Used along with the OTR button to set delayed (Standby) OTR's.
One Touch Record (OTR) Button
Select the channel and press the One Touch Record button to start an immediate recording 30 minutes to 4 hours long, or up to the tape end.
Stop Button
To stop the tape.
Rewind / Search Button
To rewind tapes. Also, during playback press this button to view the picture in rapid reverse.
Fast Forward / Search Button
To rapidly advance the tape. Also in playback press this button to do a rapid forward visual search.
Slow Motion Buttons
Press the Slow button in playback for slow motion on tapes recorded in SLP. The Up/ Down buttons let you adjust the slow motion speed from about 1/5 to about 1/30 of normal speed.
Video Button
Used to display the Video Adjust Menu.
Frame Advance Button
Press to advance the picture frame-by-frame in still mode for tapes
10
Description of Controls
recorded in SLP. Press this button to scan several seconds you want to skip in a playback.
Timer Button
To set the TV/VCR Combination for unattended recordings.
Volume Buttons (Up/ Down)
Press either Volume Up or Down button to change the sound level.
Mute Button
To turn the sound off. Press again and the sound will return.
Numeric Keys (0, 1, 2, 3, 4, 5, 6, 7, 8 and 9) Used to select tuner channels and functions
selected with OSD (On Screen Display). (100) Press this button first when selecting channels 100 through 125.
Channel Up / Down Keys
Used to select the desired TV/VCR Combination tuner channel. Can also be used to clear or reset items in a displayed program.
Time Search Button
This button can make search easier by allowing you to skip back or ahead on a tape.
Rec End Search Button
To locate the beginning of a blank portion of tape for continuous recor di ng .
Channel Search Button
Press this button to start a scan of the channels assigned to the Channel Up / Down keys. When the desired channel appears, press this button again to select it.
Tape Speed Selector (SP/LP/SLP)
Set this selector to the desired recording speed.
Rec Button
To record.
Play Button
To play back a tape.
Pause/ Still Button
To temporarily stop the tape during recording or to view a still picture during playback.
Double speed (X2) Playback Button
Press this button during playback with tapes recorded in SLP mode to search forward at twice the normal speed.
Tracking Control
Use this control during playback or double speed playback if the image is partially obscured by bands of noise.
Add/ Delete Button
Used to add or delete a selected channel.
Normal Button
Used to set all the Video Adjust controls at a factory set level.
Video Level Buttons
Used to adjust video controls.
11
On Screen Indications
On Screen Indications
Whenever a function button (Stop, FF, etc.) is pressed, or when you change channels, a 4 second OSD appears. The function name or the channel number (if tuned) are displayed as a large overlay for 2 seconds, then again for 2 seconds in a smaller overlay.
VCR Status Display
As the Recall button is pressed, the sequence of overlays shown below will be displayed as long as the arrow appears in the lower right (for about the first 5 seconds). After the arrow disappears, the overlay displayed will remain on the TV screen until it is removed by the next press of the Recall button.
OSD Menu Screen
You only need to press one of the Numeric keys on the remote control. Each Numeric key is indicated next to the feature displayed on the OSD Menu. When you select a feature turn to the section in this manual and read the full description accompanying the instructions there.
12
Loading...
+ 28 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use