Hisense U5120GW+ User guide

7.1.2CH Soundbar with Wireless Subwoofer Model: U5120GW+

USER MANUAL

Before using the soundbar, please read this manual thoroughly and retain it for future reference.

Contents

1. Important Safety Instructions ......................................................................................................... 3

1.1 Safety .........................................................................................................................................................................................................3

1.2 Warning ....................................................................................................................................................................................................4

2. What’s in the Box .............................................................................................................................. 8

3. Identifying the Parts ........................................................................................................................ 9

3.1 Main Unit ................................................................................................................................................................................................9

3.2 Wireless Subwoofer ...........................................................................................................................................................................10

3.3 Wireless Rear Speaker ...................................................................................................................................................................... 10

3.4 Remote Control .................................................................................................................................................................................. 10

4. Preparations ................................................................................................................................... 11

4.1 Prepare the Remote Control ..........................................................................................................................................................11

4.2 Replace the Remote Control Battery .......................................................................................................................................... 11

4.3 Placement and Mounting ............................................................................................................................................................... 11

4.4 Mounting the Soundbar on a Wall ..............................................................................................................................................12

4.5 Mounting the Rear Speakers on a Wall ......................................................................................................................................12

5. Connections .................................................................................................................................... 13

5.1 Dolby Atmos® ...................................................................................................................................................................................... 13

5.2 DTS: X ..................................................................................................................................................................................................... 13

5.3 Use the HDMI Socket ........................................................................................................................................................................ 13

5.4 Use the OPTICAL Socket .................................................................................................................................................................. 14

5.5 Use the COAXIAL Socket .................................................................................................................................................................14

5.6 Connect Power ................................................................................................................................................................................... 14

5.7 Pair up with the subwoofer ............................................................................................................................................................14

5.8 Pair up with the Rear Speakers ..................................................................................................................................................... 15

6. Connect to Wi-Fi .............................................................................................................................. 15

6.1 WPS mode ............................................................................................................................................................................................ 15

6.2 AirPlay setup ........................................................................................................................................................................................ 16

6.3 DTS Play-Fi app setup .......................................................................................................................................................................16

6.4 Multi-room audio ............................................................................................................................................................................... 17

6.5 Chromecast built-in .......................................................................................................................................................................... 17

7. Basic Operation .............................................................................................................................. 17

7.1 Standby/ON ......................................................................................................................................................................................... 17

7.2 Auto-Standby / Auto-Wake Feature ............................................................................................................................................ 17

7.3 Select Modes ....................................................................................................................................................................................... 17

7.4 Adjust the Bass/Treble Level ..........................................................................................................................................................18

7.5 Turn the Surround Sound ON/OFF .............................................................................................................................................. 18

7.6 Adjust the Volume ............................................................................................................................................................................. 18

7.7 Adjust the Brightness ....................................................................................................................................................................... 18

7.8 Select Equalizer (EQ) Eect ............................................................................................................................................................. 18

7.9 Set the Audio Delay (AV SYNC) .....................................................................................................................................................18

7.10 Factory Reset ...................................................................................................................................................................................... 18

8. DTS: X Operation ............................................................................................................................ 18

8.1 Neural:X / DRC / Dialog Control Feature ....................................................................................................................................18

9. OPTICAL / COAXIAL / HDMI / ARC Operation ................................................................................ 19

10. Bluetooth Operation ...................................................................................................................... 19

10.1 Pair Bluetooth-enabled Devices ................................................................................................................................................... 19

10.2 Listen to Music from Bluetooth Device ...................................................................................................................................... 20

11. USB Operation ................................................................................................................................ 20

12. Setup Menu ..................................................................................................................................... 21

13. Troubleshooting ............................................................................................................................. 22

14. Specications.................................................................................................................................. 23

1. Important Safety Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC

ÉLECTRIQUE NE PAS OUVRIR

The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sucient magnitude as to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

1.1 Safety

1 Read these instructions – All the safety and

operating instructions should be read before this product is operated.

2 Keep these instructions – The safety and

operating instructions should be retained for future reference.

3 Heed all warnings – All warnings on the

appliance and in the operating instructions should be adhered to.

4 Follow all instructions – All operating and

usage instructions should be followed.

5 Do not use this apparatus near water – The

appliance should not be used near water or moisture – for example, in a wet basement or

near a swimming pool and the like. 6 Clean only with a dry cloth. 7 Do not block any ventilation openings.

Install in accordance with the manufacturer’s

instructions. 8 Do not install near any heat sources such as

radiators, heaters, stoves, or other apparatus

(including ampliers) that produce heat. 9 Do not defeat the safety purpose of the

polarized or grounding plug. A polarized

plug has two blades with one wider than the

other. A grounding plug has two blades and

a third grounding prong. The wide blade or

the third prong is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on

or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specied

by the manufacturer.

is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13 Unplug the apparatus during lightning

storms or when unused for long periods of time.

14 Refer all servicing to qualied personnel.

Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the unit has been exposed to rain or moisture, does not operate normally, or has been dropped.

insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.

16 The apparatus shall not be exposed to

dripping or splashing. No objects lled with liquids, such as vases, shall be placed on the apparatus.

17 Minimum distance around the apparatus for

sucient ventilation is 5cm.

18 The ventilation should not be impeded by

covering the ventilation openings with items, such as newspapers,table-cloths, curtains, etc…

19 No naked ame sources, such as lighted

candles, should be placed on the apparatus.

20 Batteries should be recycled or disposed of

as per state and local guidelines.

21 The use of apparatus in moderate or tropical

climates.

Use only with the cart, stand, tripod, bracket or table specied by the manufacturer, or sold with the apparatus. When a cart or rack

This equipment is a Class II or double

Caution:

- Use of controls or adjustments or performance of procedures other than those described herein, may result in hazardous radiation exposure or other unsafe operation.

- To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture. The apparatus must not be exposed to dripping or splashing and objects lled with liquids, such as vases, must not be placed on apparatus.

- The mains plug/appliance coupler is used as the disconnect device, the disconnect device must remain readily operable.

- Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

1.2 Warning

• The battery (batteries or battery pack) shall not be exposed to excessive heat such as sunshine, re or the like.

• Before operating this system, check the voltage of this system to see if it is identical to the voltage of your local power supply.

• Do not place this unit close to strong magnetic elds.

• Do not place this unit on the amplier or receiver.

• If any solid object or liquid falls into the system, unplug the system and have it checked by qualied personnel before operating it any further.

• Do not attempt to clean the unit with chemical solvents as this may damage the nish. Use a clean, dry or slightly damp cloth.

• When removing the power plug from the wall outlet, always pull directly on the plug, never yank on the cord.

• Changes or modications to this unit not expressly approved by the party responsible for compliance will void the user’s authority to operate the equipment.

• The rating label is pasted on the bottom or back of the equipment.

Battery usage CAUTION To prevent battery leakage which may result in bodily injury, property damage, or damage to the apparatus:

- Install all batteries correctly, + and - as marked on the apparatus.

- Do not mix old and new batteries.

- Do not mix alkaline, standard (CarbonZinc) or rechargeable (Ni-Cd, Ni- MH, etc.) batteries.

- Remove batteries when the unit is not used for a long time.

For 5G Wi-Fi Device

The device for operation in the band 5150–5350 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

We hereby declares that this product

is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and UK Radio Equipment Regulations

2017.

Trademarks:

• For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. (for companies headquartered in the U.S./ Japan/Taiwan) or under license from DTS Licensing Limited (for all other companies). DTS, DTS Play-Fi, Play-Fi and the DTS Play-Fi and Play-Fi logos are registered trademarks or trademarks of DTS, Inc. in the United States and other countries. © 2021 DTS, Inc. ALL RIGHTS RESERVED.

• The Wi-Fi CERTIFIED™ Logo is a registered trademark of Wi-Fi Alliance®.

• To control this AirPlay 2–enabled speaker, iOS 11.4 or later is required. Use of the Works with Apple badge means that an accessory has been designed to work specically with the technology identied in the badge and has been certied by the developer to meet Apple performance standards.

Apple® and AirPlay® are trademarks of Apple

Inc., registered in the U.S. and other countries.

• The Spotify Software is subject to third party licenses found here: www.spotify.com/ connect/third-party-licenses.

• Google, Google Play and Chromecast builtin are trademark of Google LLC. Google Assistant is not available in certain languages and countries.

• Dolby, Dolby Vision, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories. Condential unpublished works. Copyright © 2012-2020 Dolby Laboratories. All rights reserved.

• The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Hisense is under license. Other trademarks and trade names are those of their respective owners.

Supported input audio formats

Format Function

HDMI

ARC

LPCM 2ch

LPCM 5.1ch

LPCM 7.1ch

Dolby Atmos - Dolby TrueHD

Dolby Atmos - Dolby Digital Plus

Dolby TrueHD

Dolby Digital Plus

Dolby Digital

DTS

DTS-ES Discrete 6.1

DTS-ES Matrix 6.1

DTS 96/24

DTS-HD High Resolution Audio

DTS-HD Master Audio

DTS-HD LBR

DTS:X

OPTICAL COAXIAL

● ● ● ● ●

-- -- -- ● ●

-- -- ● ● ●

-- -- -- ● ●

-- -- ● ● ●

● ● ● ● ●

-- -- -- ● ●

HDMI IN 1 HDMI IN 2

HDMI eARC

●

: Supported format.

: Unsupported format.

Note: The HDMI IN 1/2 jack does not support copy-protected audio formats such as Super Audio CD or

DVD-Audio.

Supported HDMI video formats

Resolution Frame rate 3D Color space

RGB 4:4:4

YCbCr

4:4:4

4K 4096 x 2160p 3840 x 2160p

4K 4096 x 2106p 3840 x 2106p

1920 x 1080p

1920 x 1080i 50/59.94/60 Hz

1280 x 720p

720 x 480p 59.94/60 Hz -

720 x 576p 50 Hz -

640 x 480p 59.94/60 Hz - RGB 4:4:4

50/59.94/60 Hz

23.98/24/25/

29.97/30 Hz

50/59.94/60 Hz -

23.98/24/25/

29.97/30 Hz

25/29.97/30/50/

59.94/60 Hz

23.98/24 Hz

50/59.94/60 Hz

23.98/24/29.97/ 30 Hz

◎

○

◎

YCbCr

4:2:2

YCbCr

4:2:0

RGB 4:4:4

YCbCr

4:4:4

YCbCr

4:2:0

RGB 4:4:4

YCbCr

4:4:4

YCbCr

4:2:2

RGB 4:4:4

YCbCr

4:4:4

YCbCr

4:2:2

Color

depth

8 bit

8/10/12

bit

10/12

bit

10/12

bit

8 bit

8/10/12

bit

8/10/12

bit

[HDMI Signal

Format] setting

[enhanced format]

[standard format]

Compatible with side-by-side (half width) format 3D signals

○

Compatible with frame packing and 3D signals in

◎

1) Please use a high-quality high-speed HDMI Ethernet cable that supports 18Gbps.

2) Please use a high quality high speed HDMI Ethernet cable.

format

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer. For more information go to: www.P65Warnings.ca.gov.

FCC INFORMATION (for US customers)

NOTE:

• This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protect ion agains t harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

• However, there is no guarantee that interference wil l no t occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio / TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must a ccept any interference received,

including interference that may cause undesired operation.

• Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.

IC Notice: CAN ICES-3(B)/NMB-3(B)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Warning:

- This equipment should be installed and operated with

minimum distance 20cm between the radiator & your body.

- Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.”

Réglement de la FCC (pour les clients américains)

REMARQUE :

• Ce dispositif a été testé et déclaré conforme aux limites d’un dispositif numérique de classe B, conformément à la partie 15 des règles de la FCC.

Ces limites ont pour but d'assurer une protection raisonnable contre le brouillage nuisible dans une installation résidentielle. Cet équipement produit, utilise et peut émettre de l'énergie en radio fréquence et, s'il n'est pas installé et utilisé conformément aux directives, il peut causer un brouillage nuisible dans les communications radio.

• Cependant, il n’est pas garanti que des interférences ne se produiront pas dans une installation particulière. Si cet appareil provoque des interférences nuisibles à la réception radio ou de télévision, ce qui peut être déterminé en mettant l’appareil hors tension, l’utilisateur est encouragé à essayer de corriger l’interférence par une ou plusieurs des mesures suivantes :

- Réorienter ou déplacer l’antenne de réception.

- Augmenter la distance entre l’appareil et le récepteur.

- Brancher l’appareil à une prise sur un circuit diérent de celui sur lequel le récepteur est branché.

- Consulter le revendeur ou un technicien radio/TV expérimenté.

Cet appareil est conforme à la partie 15 des règles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes :

(1) ce dispositif ne peut pas causer d’interférences nuisibles et (2) cet appareil doit accepte r toute inter férence reçue, y

compris les interférences qui peuvent causer un mauvais fonctionnement.

• Des câbles blindés doivent être utilisés avec cet apparei l pour assurer la conformité avec les limites de la classe B de la FCC.fonctionnement de I'appareil.

Avis d’Industrie Canada: CAN ICES-3(B)/NMB-3(B)

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Avertissement :

- Pour rester en conformité avec les consignes d’exposition aux RF, placez le produit à au moins 20 cm des personnes proches.

- Les changements ou modications de cet appareil non

expressément approuvées par la partie responsable de la conformité pourraient annuler l’autorisation de l’utilisateur à utiliser l’équipement.

2. What’s in the Box

Main Unit Remote Control /

AC power Cord *

(x4)

Wall Mounting Screws (x2) / Brackets (x2) /

Bracket Screw (x4) / Wall Anchors (x4)

(for main unit)

AAA Batteries x 2

Wireless Subwoofer

HDMI Cable Optical Cable

Rear speaker (x2) Dongle

Wall mounting kit

(for rear speaker)

* Power cord quantity and plug type vary by regions.

• Images, illustrations and drawings shown on this User Manual are for reference only. Actual product may vary in appearance.

• Design and specications are subject to change without notice.

User Manual /

Quick Start Guide

3. Identifying the Parts

3.1 Main Unit

9 1110 12 13

(ON/OFF) button

State Action

On • Follow source state

Semi

Press

Standby

once

Eco

Press and

Standby

hold 5 seconds

(SOURCE) button

Select the play function.

VOL+/VOL- buttons

Increase/decrease the volume level.

Wi-Fi LED indicator

LED State Status

Blink Double blink Constant on

Display Window / Remote Control Sensor Show the current status. Receive signal from the remote control.

Screws Remove the screws then install the wall

mounting screws into the back of the unit.

PF (Wi-Fi Setup) button

• Trigger Wi-Fi setup for Play-Fi.

Function

• Wi-Fi is still on.

• It still supports Play-Fi and Airplay2.

• Wi-Fi is o.

• The product enters the lower power consumption mode.

• Restarting the system will take a relatively longer time.

Wi-Fi Access Point (AP) mode

Wi-Fi Protected Setup (WPS) mode

Connected / Paired successful

1 2 3

• Press and hold the button 8 seconds

3 seconds

USB Socket

：

Wi-Fi Access Point (AP) mode

Wi-Fi Protected Setup (WPS) mode

Insert the USB device to play music.

TYPE-C Socket For the Dongle of wireless rear surround speaker. This port can't be used to connect to other

Type C devices.

OPTICAL Socket Use to connect to the OPTICAL OUT socket

on an external device.

COAXIAL Socket Use to connect to the COAXIAL OUT socket

on an external device.

HDMI OUT (TV eARC/ARC) Socket

The port for connecting a TV. The port supports the eARC/ARC HDMI feature, which allows the soundbar to play audio that originates on the connected TV.

HDMI IN (1/2) Sockets Two HDMI ports for connecting HDMI source

devices, such as a DVD player, Blu-ray Disc™ player, or gaming console. Note that only one HDMI input is usable at a time.

AC~ Socket Connect to power supply.

3.2 Wireless Subwoofer

AC~ Socket

Connect to power supply.

PAIR button

Press activate the pairing function between

the main unit and the subwoofer.

PAIR Indicator

Light stops blinking once the Subwoofer is

paired with the Soundbar.

3.3 Wireless Rear Speaker

PAIR button

Indicator

• Fast blink Rear Speaker in pairing mode

• Constant on Connected / Paired successful

• Slow blink Connection / Pairing Failed

Surround

L/R

AC ~

Screws

Press activate the pairing function between the main unit and the surround.

Set to Left or Right Surround Speaker

Connect an AC power cord

Remove the screws then install the wall screws into the back of the Rear Speaker

3.4 Remote Control

(ON/OFF)

State Action

On • Follow source state Semi Standby

Eco Standby

SURR Adjust the surround ON/OFF.

(BT) Select the Bluetooth mode. Press

Press once

Press and hold 5 seconds

(SOURCE)

Select the play function.

Function

• Wi-Fi is still on.

• It still supports Play-Fi and Airplay2.

• Wi-Fi is o.

• The product enters the lower power consumption mode.

• Restarting the system will take a relatively longer time.

and hold the (BT) button to activate the pairing function in Bluetooth mode or disconnect the existing paired Bluetooth device.

EQ Select a preset sound eect.

Skip to previous/next track in BT /

USB mode.

VOL+/VOL- Increase/decrease the volume level.

Play/pause/resume playback in BT

/USB mode. Press and hold the button for 3s to enter setup menu. Conrm a selection.

1 2 3

BASS+/- Adjust bass level.

TREBLE+/- Adjust treble level.

DIMMER+/- Adjust display brightness.

(MUTE)

Mute or resume the sound.

4. Preparations

4.1 Prepare the Remote Control

The provided Remote Control allows the unit to be operated from a distance.

• Even if the Remote Control is operated within the eective range 19.7 feet (6m), remote control operation may be impossible if there are any obstacles between the unit and the remote control.

• If the Remote Control is operated near other products which generate infrared rays, or if other remote control devices using infra-red rays are used near the unit, it may operate incorrectly. Conversely, the other products may operate incorrectly.

4.2 Replace the Remote Control Battery

1 Press and slide the back cover to open the

battery compartment of the remote control.

2 Insert two AAA size batteries. Make sure the (+)

and (–) ends of the batteries match the (+) and (–) ends indicated in the battery compartment.

3 Close the battery compartment cover.

Precautions Concerning Batteries

• Be sure to insert the batteries with correct positive “” and negative “” polarities.

• Use batteries of the same type. Never use dierent types of batteries together.

• Either rechargeable or non-rechargeable batteries can be used. Refer to the precautions on their labels.

• Be aware of your ngernails when removing the battery cover and the battery.

• Do not drop the remote control.

• Do not allow anything to impact the remote control.

• Do not spill water or any liquid on the remote control.

• Do not place the remote control on a wet object.

• Do not place the remote control under direct sunlight or near sources of excessive heat.

• Remove the battery from the remote control when not in use for a long period of time, as corrosion or battery leakage may occur and result in physical injury, and/or property damage, and/or re.

• Do not use any batteries other than those specied.

• Do not mix new batteries with old ones.

• Never recharge a battery unless it is conrmed to be a rechargeable type.

4.3 Placement and Mounting

Placement

The following are available when the rear speakers are used with the soundbar.

• You can enjoy the surround sound that makes you feel as if you were actually listening to a live performance.

• You can update the software of the rear speakers. For details, refer to the Operating Instructions supplied with the soundbar.

Note

• The rear speakers are designed exclusively for use with the soundbar and cannot be used with other devices.

• Install the rear speakers vertically.

4.4 Mounting the Soundbar on a Wall

Note:

- Installation must be carried out by qualied personnel only. Incorrect assembly can result in severe personal injury and property damage (if you intend to install this product yourself, you must check for installations such as electrical wiring and plumbing that may be buried inside the wall). It is the installer’s responsibility to verify that the wall will safely support the total load of the unit and wall brackets.

- Additional tools (not included) are required for the installation.

- Do not overtighten screws.

- Keep this instruction manual for future reference.

- Use an electronic stud nder to check the wall type before drilling and mounting.

WARNING

• To prevent injury, this apparatus must be securely attached to the oor/wall in accordance with the installation instructions.

• Suggested wall mounting height: ≤ 1.5 meters.

3. Remove the screws at the back of the unit. Install the wall mounting screws into the back of the unit.

4. Lift the unit onto the wall mount brackets and slot into place.

4.5 Mounting the Rear Speakers on a Wall

You can mount the rear speakers on a wall. 1 Tighten the wall mount brackets on the wall

with screws and screwdriver (not included). Make sure that they are securely installed.

2 Remove the screws at the back of the unit.

Install the wall mounting screws into the back of the unit.

3 Hang the rear speaker by conrming the

right/left of the rear speaker.

Check the Surround L/R on the rear of the

rear speaker. “Surround R” is for the right, “Surround L” is for the left.



1156mm



1. Drill 4 parallel holes (Ø 5.5-6 mm each according to wall type) in the wall. The distance between the holes should be 1156 mm.

2. Firmly x 1 dowel into each hole in the wall if necessary. Tighten the wall mount brackets on the wall with screws and screwdriver. Make sure that they are securely installed.

5. Connections

5.1 Dolby Atmos®

Dolby Atmos® gives you immersive listening experience by delivering sound in three dimensional space, and all the richness, clarity, and power of Dolby sound. For more information, please visit dolby.com/technologies/dolby-atmos

HDMI

eARC/ARC

HDMI OUT

(TV eARC/ARC)

5.2 DTS: X

DTS: X The border sound is no longer constrained by xed-position speaker placement or specic channel signals. It can be exibly debugged according to the playback environment to achieve the best sound performance in this environment.

For using Dolby Atmos® / DTS: X

Dolby Atmos® / DTS: X is available in HDMI IN 1 / HDMI IN 2 and HDMI eARC/ARC mode. For the details of the connection, please refer to “HDMI Connection”.

1. To use Dolby Atmos® / DTS: X in HDMI IN 1 and HDMI IN 2 mode, Your TV had to support Dolby Atmos® / DTS: X or HDMI audio passthrough.

2. Make sure that “Bitstream“, ”RAW“ or ”No Encoding“ is selected for bitstream in the audio output of the connected external device (e.g. Blu-ray DVD player, TV etc.).

3. While entering Dolby Atmos / DTS: X / Dolby Digital / PCM format, the soundbar will show DOLBY ATMOS / DTS: X / DOLBY AUDIO / PCM AUDIO.

5.3 Use the HDMI Socket

Some 4K HDR TVs require the HDMI input or picture settings to be set for HDR content reception. For further setup details on HDR display, please refer to the instruction manual of your TV.

Using HDMI to connect the soundbar, AV equipment and TV:

Method 1:

eARC / ARC (Audio Return Channel)

The eARC / ARC (Audio Return Channel) function allows you to send audio from your ARC- compliant TV to your soundbar through a single HDMI connection. To enjoy the ARC function, please ensure your TV is both HDMI-CEC and ARC compliant and set up accordingly. When correctly set up, you can use your TV remote control to adjust the volume output (VOL +/- and MUTE) of the soundbar.

- Connect the HDMI cable from unit's HDMI OUT (TV eARC/ARC) socket to the HDMI (ARC) socket on your ARC compliant TV. Then press the remote control to select HDMI eARC.

Tips:

• Your TV must support the HDMI-CEC and ARC function. HDMI-CEC and ARC must be set to On.

• The setting method of HDMI-CEC and ARC may dier depending on the TV. For details about ARC function, please refer to the owner’s manual.

• ARC only works with devices that are HDMI ARC capable as well as with an HDMI 1.4 cable (and higher).

Method 2: Standard HDMI

- If your TV is not HDMI ARC-compliant, connect your soundbar to the TV through a standard HDMI connection.

HDMI OUT

Blu-ray Player / DVD Player /

HDMI OUT

(TV eARC/ARC)

Recorder / Set-top Box...

HDMI IN 1 HDMI IN 2

HDMI IN

1. Use an HDMI cable to connect the soundbar's HDMI OUT (eARC/ARC) socket to the TV’s HDMI IN socket.

2. Use an HDMI cable to connect the soundbar's HDMI IN (1 or 2) socket to your external devices (e.g. games consoles, DVD players and blu-ray).

5.4 Use the OPTICAL Socket

- Connect an OPTICAL cable to the TV’s

OPTICAL OUT socket and the OPTICAL socket on the unit.

OPTICAL

5.5 Use the COAXIAL Socket

• You also can use the COAXIAL cable to connect the TV's COAXIAL OUT socket and COAXIAL socket on the unit.

COAXIAL

Tip: The unit may not be able to decode all digital audio formats from the input source. In this case, the unit will mute. This is NOT a defect. Ensure that the audio setting of the input source (e.g. TV, game console, DVD player, etc.) is set to PCM or Dolby Digital (Refer to the user manual of the input source device for its audio setting details) with HDMI / OPTICAL / COAXIAL input.

5.6 Connect Power

•

Risk of product damage!

the power supply voltage corresponds to the voltage printed on the back or the underside of the unit.

• Before connecting the AC power cord, ensure you have completed all other connections.

Ensure that

• Soundbar

Connect the mains cable to the AC~ socket

of the main unit and then into a mains socket.

• Subwoofer

Connect the mains cable to the AC~ socket of

the Subwoofer and then into a mains socket.







* Power cord quantity and plug very by regions.

5.7 Pair up with the subwoofer

Automatic pairing

The subwoofer and soundbar will automatically pair when both units are plugged into the mains sockets and turned on. No cable is needed for connecting the two units.

• Determine the status based on the wireless Subwoofer indicator.

LED State Status

Fast blink Constant on Slow blink

Subwoofer in pairing mode

Connected / Paired successful

Connection / Pairing Failed

NOTE:

- Do not press the Pair button on the rear of the subwoofer, except for manual pairing.

- If the automatic pairing fails, pair the subwoofer with the main unit manually.

Manual pairing

1. Ensure that all the cables are well connected and the main unit is in Standby mode.

2. Press and hold the Pair button on the rear of the subwoofer for a few seconds. The subwoofer will enter the pairing mode and the Pair Indicator will blink quickly.

3. Press

4. After the wireless connection succeeded, the

5. If the Pair indicator blinks, the wireless

the button on the main unit or on

the remote control to switch the main unit on.

Pair Indicator will light up.

connection has failed. Unplug the cable of the subwoofer and then reconnect the main cable after 3 minutes. Repeat step 1 ~ 4.

NOTE:

• If the wireless connection fails again, check if there is conict or strong interference (for example, interference from an electronic device) around your location. Remove these conicts or strong interferences and repeat the above procedures.

• The subwoofer should be within 6m (18 feet) of the soundbar in an open area.

• If the main unit is not connected with the subwoofer and it is in On mode, the POWER Indicator will ash. Follow step 1 ~ 4 above to pair the subwoofer to the main unit.

5.8 Pair up with the Rear Speakers

Note

• Surround should be installed within a 6m range of the main soundbar.

• When manually pair up soundbar with surround L, the surround R must be powered off. When manually pair up soundbar with surround R, the surround L must be powered off.

• Do not press the Pair button on the rear of the surround except for manual pairing.

Automatic Pairing

1 Insert the Dongle of wireless rear surround

speaker.

2 Connect the power cord to both soundbar &

surround & connect both to a power source.

3 Turn on the soundbar. Both soundbar &

surround R/L will connect automatically wirelessly.

Manual pairing

• If no audio from the surround can be heard, manually pair up the surround.

1. Ensure that all the cables are well connected and the soundbar is in Standby mode.

2. Press and hold the Pair button on the rear of the surround for a few seconds. The surround will enter the pairing mode and the Pair Indicator will blink quickly.

3 Turn on the soundbar. Both soundbar &

surround R/L will connect automatically wirelessly.

• The Pair indicator on the surround will become solid when successful.

4. If the Pair indicator blinks, the wireless connection has failed. Unplug the cable of the surround and then reconnect the main cable after 4 minutes. Repeat step 1 ~ 3.

To the mains socket

6. Connect to Wi-Fi

6.1 WPS mode

If your router has Wi-Fi Protected Setup (WPS), you can set up the connection without entering a password.

1. Press and hold the PF (Wi-Fi Setup) button for 4 seconds. You will hear a tone and the Wi-Fi light will begin double blink.

2. Press the WPS button on your router. The button is normally marked with this WPS logo.

WPS

3. Follow the instructions in the DTS Play-Fi app to start pairing.

Note

• WPS is not a standard feature on all routers. If your router does not have WPS then use Standard Wi-Fi Setup.

• Press the PF (Wi-Fi Setup) button once if you want to exit the WPS mode or it will automatically exit after 2 minutes.

6.2 AirPlay setup

Use AirPlay to set up the Wi-Fi connection of iOS device (iOS7 or later) and Soundbar. 1 Press and hold PF (Wi-Fi Setup) button

located at the back cabinet for 8 sec to trigger the Wi-Fi connection.

2 Wait until the Wi-Fi light indicator turns from

a fast blink to a slow pulse. A slow pulse indicates that the speaker is entering the WiFi setup mode.

3 On your iOS device go to: Settings > Wi-Fi >

select network [Play-Fi device (xxxxxx)]

iOS Wi-Fi set up by AIRPLAY

Settings Wi-Fi

Wi-Fi

Networks

SET UP NEW AIRPLAY SPEAKER…

Play-Fi DeviceXXXXXXXX

4. Soundbar will be automatically recognized as Airplay device. Tap on [Set up new Air-Play speaker].

5. Tap on [Show Other Networks…] and select your home network to which you want soundbar to connect.

6. After a successful Wi-Fi connection, the Wi-Fi light indicator stops pulsing and stays on. After setting up this product on your Wi-Fi network, you can control it from any smartphone or tablet on the same network.

6.3 DTS Play-Fi app setup

(For iOS and Android version)

By connecting this unit and mobile phones, tablets (such as iPad, iPhone, iPod touch, Android phones, etc.) to the same Wi-Fi network, you can then use the DTS Play-Fi to control the soundbar to listen to audio les.

1. Connect your phone or tablet to the same Wi-Fi network that you want to connect your soundbar.

2. Download and install the DTS Play-Fi on a phone or tablet.

Play-Fi

• Make sure your router is turned on and working properly.

3 Press and hold PF (Wi-Fi Setup) button

located at the back cabinet for 8 sec to trigger the Wi-Fi connection.

• Until the speaker make a second tone and then release the button.

4 Wait until the Wi-Fi light indicator on the back

cabinet goes from a fast blink to a slow pulse. When it begins pulsing slowly, it indicates that the speaker is entering the Wi-Fi setup mode.

5 Launch the DTS Play-Fi. Follow the

instructions in the App to connect this product to your Wi-Fi network.

6 After a successful Wi-Fi connection, the Wi-Fi

light indicator stops pulsing and stays on. After setting up this product on your Wi-Fi network, you can control it from any smartphone or tablet on the same network.

• When using the app to play music, the display panel will show PLAY-FI.

7 After connection, you can change the device

name. There are several names to choose from or create your own by choosing Custom Name at the end of the name list. Otherwise, it follows the default name.

8 After connection, this product may perform

a software update. Upgrade to the latest software when it is your rst time set up. The software upgrade may take several minutes. Do not unplug your speaker, turn o your device, or leave the network during the update.

Note

• After connection, the product may perform a software update. Upgrade is required after initial setup. Without the upgrade, not all produc t features can be available.

• When the rst time setup is not successful, hold down the Wi-Fi button on Soundbar for 8 seconds until you hear the second tone and the Wi-Fi light changes to slow pulse. Reset the Wi-Fi connection, restart the app and star t the setup again.

• If you want to change from one network to another, you need to setup the connection again. Press hold down the PF (Wi-Fi Setup) but ton on the Soundbar for 8 seconds to reset the Wi- Fi connection.

6.4 Multi-room audio

• This soundbar can be used as part of multiroom speaker setup. This means that the same music can be played from your soundbar and other compatible speakers simultaneously throughout your home.

• To use this feature, make sure the soundbar and your smartphone / tablet are on the same network. You can use Google Home, Airplay 2 or DTS Play-Fi app to control compatible multiroom speakers. You can then play the music on multiple speakers at the same time, assign speakers to dierent groups, control the volume individually, or use master volume to change the volume on all speakers at the same time.

6.5 Chromecast built-in

• This soundbar supports Chromecast builtin feature that allows you to cast music from Chromecast compatible apps to your soundbar.

• To use this feature, make sure the soundbar and your smartphone / tablet are on the same network. Start playing music on a Chromecastenabled app and cast it to your soundbar simply by clicking the (cast) button and selecting the soundbar from the list.

7. Basic Operation

7.1 Standby/ON

When you rst connect the main unit to the mains socket, the main unit will be in Standby mode.

• Press the

button on the unit or on the

remote control to switch the unit ON.

• Press the

button again to switch the unit

back to STANDBY mode.

State Action

On • Follow source state

Semi Standby

Eco Standby

Press once

Press and hold 5 seconds

Function

• Wi-Fi is still on.

• It still supports Play-Fi and Airplay2.

• Wi-Fi is o.

• The product enters the lower power consumption mode.

• Restarting the system will take a relatively longer time.

• Disconnect the mains plug from the mains socket if you want to switch the unit OFF completely.

7.2 Auto-Standby / Auto-Wake Feature

• [Auto-Standby] Your soundbar has been

programmed to enter Standby mode automatically when no audio is detected for 15 minutes. For example, this would happen when pausing playback, or should the soundbar be left on accidentally.

• [Auto-Wake] If a TV or an external device is connected (COAXIAL/OPTICAL socket), the unit will switch on automatically when the TV or the external device is switched on.

To disable this feature, please follow the steps below:

1. During ON mode, pointing the remote at the soundbar, press and hold the

button for 3

seconds to open the menu.

- The unit’s display will scroll “MENU”.

2. Press the

button 6 times in succession

：

the display shows: Auto Wake [ON / OFF].

or Press the

button 7 times in succession,

the display shows: Auto Standby [ON / OFF].

3. Select the content with VOL +/- button on the remote control, and then press

to conrm

your selection and exit the settings.

• Repeating these steps will toggle the feature "ON" and "OFF".

7.3 Select Modes

• Press the the unit or on the remote control to select the OPTICAL, COAXIAL, HDMI ARC, HDMI 1,

HDMI 2, BT (Bluetooth) and USB mode.

(SOURCE) button repeatedly on

• Press the select the BT (Bluetooth) mode.

• The selected mode will show on the display.

Display Mode

Note

• Play-Fi is not an optional source. Play-Fi needs to be directly controlled by app.

button on the remote control to

ARC

HDMI IN 1

HDMI IN 2

OPTICAL

COAXIAL

Bluetooth

Connected Connection

USB

7.4 Adjust the Bass/Treble Level

• Press the BASS +/- buttons on the remote control to adjust bass level (bass +5 ~ bass -5).

• Press the TREBLE +/- buttons on the remote control to adjust treble level (treble +5 ~ treble -5).

7.5 Turn the Surround Sound ON/OFF

• Press the SURR button on the remote control to turn on the surround sound. Press this button again to turn o the surround sound.

7.6 Adjust the Volume

• Press the VOL+ / VOL- buttons on the unit or on the remote control to adjust the volume.

• If you wish to turn the sound o, press the

(MUTE) button on the remote control. Press the the VOL+ / VOL- buttons to resume normal listening.

(MUTE) button again or press

7.7 Adjust the Brightness

- Press the DIMMER +/- button on the remote

control to select brightness level.

7.8 Select Equalizer (EQ) Eect

• While playing, press the EQ button on the remote control to select desired preset equalizers: MUSIC, MOVIE, NEWS, SPORT,

NIGHT, GAME, AI EQ.

7.9 Set the Audio Delay (AV SYNC)

• Video image processing, sometimes longer than the time required to process the audio signal. This is called “delayed.” Audio Delay feature is designed to remedy this delay.

• Set the audio delay, provided only for the current playback mode. (As provided in the HDMI ARC audio delay mode, the delay mode is valid only for the HDMI ARC).

- By default, the audio delay is set to 00.

1. During ON mode, press and hold the button for 3 seconds to open the menu, then press the The unit’s display will scroll “ LT 00”.

2. Press the VOL+/- buttons will be a 10 ms frequency hopping to adjust the delay time. Set 200 ms maximum delay.

3. Press the

Tip:

• Adjustment range: [00~200ms]

• The audio delay setting is only valid for digital audio (eg HDMI IN, HDMI ARC, COAXIAL, OPTICAL).

button 9 times in succession.

button or exit settings 10S.

7.10 Factory Reset

Reset device to default setting

• In standby mode, press the [ BASS-] buttons on the remote control them in sequence, the display shows “RESET” t o reset the factory default settings of the host.

• Set is ON, press and hold the until the display shows “RESET” to reset the WiFi module to the factory default settings.

, , VOL+,

(MUTE) button

8. DTS: X Operation

8.1 Neural:X / DRC / Dialog Control Feature

- DTS:X® technologies provide users with virtual multi-channel virtual surround eects, creating an immersive audio volume.

1. During ON mode, pointing the remote at the soundbar, press and hold the seconds to open the menu.

2. The unit’s display will scroll “MENU”.

3. Neural:X Setting: Press the times in succession：the display shows: Dts Neural [ON / OFF].

button for 3

button 11

DRC Setting: Press the

button 12 times in succession, the display shows: Dts Drc Heavy / Dts Drc Mid / Dts Drc Min.

or Adjust the Dialog Control: Press the

button 13 times in succession, the display shows: Dts Dialog Control 0~6.

4. Select the content with VOL +/- buttons on the remote control, and then press

conrm your selection and exit the settings.

- Repeating these steps will toggle the feature ON and OFF.

9. OPTICAL / COAXIAL / HDMI / ARC Operation

1 Ensure that the unit is connected to the TV or

audio device.

2 Press the

unit or on the remote control to select the

OPTICAL, COAXIAL, HDMI 1, HDMI 2, HDMI ARC mode.

3 Operate your audio device directly for

playback features.

4 Press the VOL +/– button to adjust the

volume to your desired level.

Tip:

• The unit may not be able to decode all digital audio formats from the input source. In this case, the unit will mute. This is NOT a defect. Ensure that the audio setting of the input source (e.g. TV, game console, DVD player, etc.) is set to PCM or Dolby Digital (Refer to the user manual of the input source device for its audio setting details) with HDMI IN 1 / HDMI 2 / HDMI ARC / OPTICAL / COAXIAL input.

• When selecting a dierent audio format, the unit will display the following as follows:

Audio (abbreviation) Display

LPCM 2ch PCM AUDIO LPCM 5.1ch PCM AUDIO LPCM 7.1ch PCM AUDIO Dolby Digital DOLBY AUDIO Dolby TrueHD DOLBY AUDIO Dolby Digital Plus DOLBY AUDIO Dolby Atmos -

Dolby TrueHD Dolby Atmos -

Dolby Digital Plus

(SOURCE) repeatedly on the

DOLBY ATMOS

DTS DTS DTS Discrete Surround DTS DTS-ES 6.1 Matrix DTS DTS-ES 6.1 Discrete DTS DTS 96/24 DTS DTS 96/24 ES Matrix DTS DTS Express DTS DTS-ES 8-Channel Discrete DTS DTS-HD High Resolution DTS-HD DTS-HD Master Audio DTS-HD DTS:X DTS:X DTS:X Master Audio DTS:X

10. Bluetooth Operation

10.1 Pair Bluetooth-enabled Devices

The rst time you connect your bluetooth device to this player, you need to pair your device to this player.

Note:

- The operational range between this player and a Bluetooth device is approximately 26 feet (8m) (without any object between the Bluetooth device and the unit).

- Before you connect a Bluetooth device to this unit, ensure you know the device’s capabilities.

- Compatibility with all Bluetooth devices is not guaranteed.

- Any obstacle between this unit and a Bluetooth device can reduce the operational range.

- If the signal strength is weak, your Bluetooth receiver may disconnect, but it will re-enter pairing mode automatically.

1 During ON mode, press the

repeatedly on the unit or the the remote control to select Bluetooth mode. “NO BT” will show on the display if the unit is not paired to any Bluetooth device.

2 Activate your Bluetooth device and select

the search mode. “Hisense U5120GW+” will appear on your Bluetooth device list.

- If you cannot nd the unit, press and hold the

button to be searchable. The display

will show “BT Pairing” and you will hear "Pairing" from the unit.

3 S elect “Hisense U5120GW+” in the pairing

lis t. After successful pairing, you will hear "Paired" from the unit, and the display panel shows “BT_IN”.

button

button on

4 Play music from the connected Bluetooth

device.

To disconnect the Bluetooth function, you can :

- Switch to another function on the unit.

- Disable the function from your Bluetooth device.The Bluetooth device will be disconnected from the unit after the “Disconnected” voice prompt.

- Press and hold the

Tips:

• Enter "0000" for the password if necessary.

• If no other Bluetooth device pairs with this player within two minutes, the player will recover its previous connection.

• The player will also be disconnected when your device is moved beyond the operational range.

• If you want to reconnect your device to this player, place it within the operational range.

• If the device is moved beyond the operational range, when it is brought back, please check if the device is still connected to the player.

• If the connection is lost, follow the instructions above to pair your device to the player again.

button.

10.2 Listen to Music from Bluetooth Device

- If the connected Bluetooth device supports Advanced Audio Distribution Prole (A2DP), you can listen to the music stored on the device through the player.

- If the device also supports Audio Video Remote Control Prole (AVRCP), you can use the player's remote control to play music stored on the device.

1. Pair your device with the player.

2. Play music via your device (if it supports A2DP).

3. Use supplied remote control to control play (if it supports AVRCP).

Start, pause or resume play.

Skip to the previous or next track.

11. USB Operation

1 Insert the USB device.

2 Press the button repeatedly on the unit or

on the remote control to select USB mode.

3 During playback:

Start, pause or resume play.

Skip to the previous or next track.

Tips:

• The unit can support USB devices with up to 32 GB of memory.

• This unit can play WAV / WMA / MP3 / FLAC / DSD / ALAC.

• This product may not be compatible with certain types of USB storage devices.

• If you use a USB extension cable, USB hub, or USB Multifunctional card reader, the USB storage device may not be recognized.

• Do not remove the USB storage device while reading les.

12. Setup Menu

buttons.

1. During ON mode, press and hold the button for 3 seconds to open the menu.

2. Select the content with

3. Change the initial values for each of the settings with VOL +/- buttons.

4. Press the

button to conrm your selection

and exit the settings.

• If no button is pressed within 15 seconds, the system will automatically exit the menu.

Description

(press VOL + / - )

)

Select Equalizer (EQ) Eect

MUSIC, MOVIE, NEWS, SPORT,

(

NIGHT, GAME, AI EQ)

Switch Surround Sound [ON / OFF]

Adjust the Bass Level

Adjust the Treble Level Adjust the Brightness

Exit menu to take eect)

(

Switch Auto Wake [ON / OFF]

Switch Auto Standby [ON / OFF]

If there is no surround connection. Not adjustable.

If there is surround connected. Adjust the surround speakers Volume

Set the Audio Delay (AV SYNC)

Switch: HI-RES Remaster [ON / OFF]

Switch: Dts Neural [ON / OFF]

Switch: Dts Drc Heavy / Dts Drc Mid / Dts Drc Min

Dts Dialog Control Value

Display

(press

13. Troubleshooting

To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this unit, check the following points before requesting service.

No power

• Ensure that the AC cord of the apparatus is properly connected .

• Ensure that there is power at the AC outlet.

• Press standby button to turn the unit on.

Remote control does not work

• Before you press any playback control button, rst select the correct source.

• Reduce the distance between the remote control and the unit.

• Insert the battery with its polarities (+/-) aligned as indicated.

• Replace the battery.

• Aim the remote control directly at the sensor on the front of the unit.

No sound

• Make sure that the unit is not muted. Press

or VOL+/– button to resume normal

listening.

• Press

• Unplug both the soundbar and the

• Ensure the audio setting of the input source

• The subwoofer is out of range, please move

• The soundbar may have lost connection with

• The unit may not be able to decode all digital

button on the unit or on the remote control to switch the soundbar to standby mode. Then press the switch the soundbar on.

subwoofer from the mains socket, then plug them again. Switch on the soundbar.

(e.g. TV, game console, DVD player, etc.) is set to PCM or Dolby Digital mode while using digital (e.g. HDMI, OPTICAL, COAXIAL) connection.

the subwoofer closer to the soundbar. Make sure the subwoofer is within 5 m of the soundbar (the closer the better).

the subwoofer. Re-pair the units by following the steps on the section “Pairing the Wireless Subwoofer with the Soundbar”.

audio formats from the input source. In this case, the unit will mute. This is NOT a defect. device is not muted.

button again to

I can’t nd the Bluetooth name of this unit on my Bluetooth device for Bluetooth pairing

• Ensure the Bluetooth function is activated on your Bluetooth device.

• Ensure you have paired the unit with your Bluetooth device.

The Soundbar turns o

• When the unit's external input signal level is too low, the Sound Bar will be automatically turn o after 15 minutes. Please increase the volume level of your external device.

The subwoofer is idle or the indicator of subwoofer do not light up.

• Please unplug power cord from the mains sockect, and plug it in again after 4 minutes to reset the subwoofer.

Wi-Fi

Wi-Fi connection cannot be established.

• Check the availability of WLAN network on the router.

• Place the Wi-Fi router closer to the unit.

• Make sure the password is correct.

• Check the WLAN function or reboot the modem and Wi-Fi router.

Play-Fi

Cannot discover the Play-Fi supported devices from the app.

Make sure the device is connected to the Wi-Fi.

Cannot play Play-Fi music.

• Certain network service or contents available through the device may not be accessible in case the service provider terminates its service.

• When the rst time setup is not successful, close the DTS Play-Fi. Restart the app.

• When the speaker is set as Stereo Pairs or Surround Sound, the speaker need to be disconnected in the app before being used separately.

14. Specications

Model Name U5120GW+

Soundbar

Power Supply AC 100-240V~ 50/60Hz Power Consumption 45 W Standby Consumption < 0.5 W USB port for playback

USB Compatibility USB Playback support / le formats

TYPE-C for the Dongle of wireless rear speaker 5V Dimension (WxHxD) 1200 x 75 x 112 mm / 47.2" x 2.9" x 4.4 Net weight 5 kg / 11 lbs Frequency Response 120Hz ~ 40KHz Operating Humidity Range Operating Temperature 0°C - 45°C

Wireless Specication

Network supported

Bluetooth version / proles Bluetooth frequency range Bluetooth Max. transmitting power (EIRP)

2.4G Wireless frequency range

2.4G Max. transmitting power (EIRP)

5.8G Wireless frequency range

5.8G Max. transmitting power (EIRP) Modulation Type GFSK, π/4 DQPSK

Subwoofer

Power Supply AC 100-240V~ 50/60Hz Power Consumption 50 W / < 0.5 W (StandBy) Dimension (WxHxD) 250 x 355 x 250 mm / 9.8" x 14" x 9.8" Net weight 7 kg / 15.4 lbs Frequency Response 40Hz~120Hz

Rear Speakers

Power Supply AC 100-240V~ 50/60Hz Power Consumption 15 W / < 0.5 W (StandBy)

Speaker

Dimension (WxHxD) 91 x 144 x 113 mm / 3.6" x 5.6" x 4.4" Net weight 0.7 kg / 1.5 lbs Frequency Response 40Hz~120Hz

Amplier (audio output power)

Soundbar 330 W (30 W x 11） Subwoofer 180 W Rear speaker 60W (30Wx2) Total 570 W

Remote Control

Distance/Angle 19.7 feet (6m) / 30° Battery type AAA (1.5V X 2)

imped

ance

500mA

5V Hi-Speed USB (2.0) / FAT32 / FAT16 32G (max) , WAV/WMA/MP3/FLAC/DSD/ALAC

500mA

40% ~ 60%

WiFi IEEE 802.11a/b/g/n/ac Wireless Frequency Band (Wi-Fi) / Radio Frequency Power Transmitted (EIRP)

2.4G Wi-Fi: 2400 MHz~2483.5 MHz / ≤20dBm

5.1G Wi-Fi: 5150 MHz~5350 MHz / ≤20dBm

5.8G Wi-Fi: 5725 MHz~5850 MHz / ≤14dBm V 4.2 (A2DP, AVRCP)

2400 MHz ~ 2483.5 MHz ≤ 5 dBm

2400 MHz ~ 2483 MHz ≤ 10 dBm

5725 MHz ~ 5850 MHz ≤ 3 dBm

8 Ω (2.5” X 2)

U5120GW+

Hisense_U5120GW+_IFU (EN) V0.5_220310

Hisense U5120GW+ User guide

Specifications and Main Features

Frequently Asked Questions

User Manual