R
COLOUR PLASMA DISPLAY TV
USER'S MANUAL
PDP5010EU
Part No:
OSD Language Settings
Using the GENERAL SETTINGS menu
OSD LANGUAGE
CHANGE PASSWORD
GENERAL SETTINGS
LANGUAGE ENGLISH
The symbol of the dustbin barred means that this apparatus cannot be put at the
rebus with not sorted waste domestic running.
It is interdict to throw with not sorted waste domestic running, of deposited on the
public thoroughfare or at any other place not envisaged to this end. This apparatus
contains substances being able to be harmful for the environment.
The presence of certain substances can have harmful effects on the environment.
The presence of certain substances can have harmful effects on the environment.
This apparatus profits from a specific treatment of recycling for the re-use of the matters which make it
up.
This apparatus must be thrown only to the places envisaged. Inform near your authority to know the
places of electronic collection of waste.
Your sale point must collect this apparatus against the purchase of a new one for its recycling.
The selective collection of waste electronics is to reduce the number of substance vermin not recycled
and to thus contribute to the environment.
Selecting a location for
- 3-
Preparation for Using your new TV
MENU button
Connecting your TV
Caution: Do not plug the TV in until you have finished connecting all of your equipment.
Connecting to A/V equipments
To enjoy its multimedia features, you can connect your to A/V equipments such as VCR, DVD, STB, Satellite
receiver, Camcorder, Audio amplifier etc., and select signal sources using your remote control.
devices as shown below.
TV
Connect the
Notes: Please pay attention to the relationship between Video Port and Audio Port. .
- 4 -
Preparation for Using your new TV
Connecting to A Computer
You can use your TV as a monitor/speakers for connecting through its 15pin standard RGB
interface and PC audio interface.
Connect the devices as shown below.
your computer by
Connecting to an antenna
To enjoy the terrestrial signal transmitted by your local TV station, you need an indoor or outdoor antenna
(not supplied). Perfect picture quality requires a good signal and generally means that an outdoor antenna
must be used. The exact type and location of the antenna will depend on your particular area. Consult your
local dealer or service personnel for best advice. If you are a subscriber of your local CATV net, the outdoor
or indoor antenna is not needed. Connect the equipments as the following figure.
Plug(not supplied)
Adaptor (not supplied)
Loosen the screw
COAXIAL CABLE (75W )
TWIN-LEAD FEEDER(300 W )
Insert the feeder in
The signal comes from:
An outdoor antenna
An indoor antenna
CATV net
Tighten the screw
- 5 -
Using the remote control
Preparing the remote control for use
Installing the remote control batteries
1. Open the battery cover on the back of the remote control.
2. Install two AAA size(1.5V) batteries. Match the + and - signs on the batteries to the signs on the battery
compartment.
3. Close the battery cover.
Note:
1.Dispose of your batteries in a designated disposal area. Do not throw batteries into fire.
2.Do not mix battery types or combine used batteries with new ones.
3.Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment.
4.If you do not intend to use the remote control for a long time, remove the batteries.
5.The effective range of remote control is suggested in the figure.
-6 -
30
30
8m
3m 3m
1m
30
8m
30
1m
Using the remote control
Learning about the remote control
1
PIP
Power : Power on/off
Channel Number :Direct channel selction
Red/PIP :
Fast text/ Select the OFF/PIP/POP Mode
Sub.Ch.
Green/Sub.Ch.:
Fast text / Select Sub. Picture source
Swap
Yellow/Swap :
Fast text /Swap between Main and Sub.picture
Blue/Main Ch. :
Main Ch.
Fast text / Select Main. Picture source
Recall : Return to previous channel
Display :Display current channel number or input mode
P.Mode: Select picture mode
1
S.Mode: Select sound mode
Text : Enter Teletext mode
Mute: Mute sound
Menu :Call up /hide the main menu
<CH+> :Channel up /Cursor up
<CH-> :Channel down/Cursor down
<VOL+>: Volume up/Cursor right
<VOL-> : Volume down/Cursor left
Zoom/Sbu. Code:
Adjust zoom ration/Teletext operation : Sub. Code
Still : Snapshooting
QQ.V
/Reveal :
I II
Mono,Stereo operation/ Teletextoperation : Reveal
Video/index:
Swtich to SCART1 mode and Video mode
/Teletext operation: Index
1
S-Video/Hold :
Switch to SCART2 mode/Teletext operation: Hold
PC/Size:
Switch to PC mode/Teletext operation: Size
YPbPr /Cancel:
Switch to YPbPr mode/Teletext operation :Cancel
DVI/Mix:
Switch to DVI / Teletext operation : Mix
Time:
Enter SLEEP menu/ Teletext operation : Time
- 7 -
Using the TV features
Understanding the TV features
Multimedia - TV receiver, Video monitor and PC display, all in one.
Wider viewing angle, 16:9 display - over 160 viewing angle, 16:9 ergonomical display panel
Digital display device - truthfully reproducing the images, without distortion or blurring, irrespective
of magnetic or geomagnetic effect.
200 channels storage
Sleep timer
Teletext with 252 pages memory
NICAM
Dual SCART interface
Multi-language OSD
Basic Operations
Power ON/OFF
1. Connect the TV to power outlet, The Power indicator will be red and
then turn blue. Several seconds later, TV picture will display on the screen.
2. Press the <Power> button on the remote control to turn off the TV temporarily
and the Power indicator turn red, your set is at Stand-By mode.
3. Press any button from the <Power> button ,<CH+>button ,<CH->button on the
remote control ,your set will quit Stand-By Mode and rework again.
Push the <Chanel up> or < Chanel down > Key on the front control board ,your
set also quit Stand-by Mode and rework again.
4. If you decide to shut down the TV for a long time, it is recommended that you
unplug the power cord.
Signal source selection
Dear customer ,two ways for your selecting the signal source.
The first way is ,Please take your remote control:
Press the <CH+>or <CH-> button to select TV input;
Press the <Video> button to select Scart1(CVBS/RGB) input ;
Press the <Video> button once more to enter Video input ;
Press the <S-Video> button to select SCART2(Y-C)input ;
Press the <YPbPr> button to select YPbPr/YCbCr input;
Press the <PC> button to select PC input;
Press the <DVI>button to select the DVI input.
POWER
INDICATOR
If you can not find your remote control immediately, do not worry ,the other way for your selecting signal source.
Please Push the <TV/AV> Key on the front control board , a Source OSD Menu will display on the screen. Push
the <Chanel up> or <Chanel down> Key ,you can select the Signal source ,Push the <Volume up> Key to ensure
your selection.
- 8 -
Select channels by numbers
To select a channel : Press the channel numbers in series to select channel directly.
For example, to seclect channel 120,
Press the button 1, and 1_ _ will display on the top right corner of the screen,
then press the button 2, 12_ will display, press the button zero, you can enjoy the program of channel 120.
NOTE:1) When you changing the channel, the sound state, colour system state& sound system state graphics can be
displayed below the channel number. There are 3 sound states in this TV. If the sound is mono, the graphics
is , If the sound is stereo, the graphics is . If the sound is NICAM dual I/II, the graphics is . But the
colour system state & sound system state is you preset the state
When you changing the channel, the sound of current channel will be firstly changed to stereo or NICAM dual
according to the sound state of current channel. You can press the I/II button on the remote control to change
current sound type.
Adjust Volume
When menu is not displayed on the screen, Press the <VOL->or<VOL+>button on the remote control to adjust the
volume level. Push the <Volume up> or <Volume down> Key to adjust the volume level also.
Use <Recall> button
Press the <Recall> button on the remote control repeatedly to alternate between the present channel and the
previous channel.
Display channel number
Press <Display> button on the remote control to display the present channel number, but it will also disappear 3
seconds after your pressing.
Select picture modes
You can select the picture mode fromamong three preset modes and one user-set
mode.
Press the < P.mode> button on the remote control repeatedly to select the desired
picture mode.
Select sound modes
You can select the sound mode from among three preset modes and one user-set
mode.
Press the <S.mode> button on the remote control repeatedly to select the desired
sound mode.
Use <Still> button
Press the <Still> button on the remote control to snapshot the present picture.
Press this button again to return to normal watching.
Bright
Normal
Soft
User
Speech
Normal
Music
User
- 9 -
Using the TV features
Using the CHANNEL menu
CHANNEL NUM
1) Press the <Menu> button to enter the main menu.
2) Press the < button to select the item CHANNEL.
3) Press the < button to select CHANNEL NUM.
4) Press the < button to select the present channel.
VOL+> or <VOL->
CH+> or <CH->
VOL+> or <VOL->
SOUND SYSTEM
1) Press the <Menu> button to enter the main menu.
2) Press the < button to select the item CHANNEL.
3) Press the < button to select SOUND SYSTEM.
4) Press the < button to switch among I, B/G, D/K, L and L` .
Suggestion:
VOL+> or <VOL->
CH+> or <CH->
VOL+> or <VOL->
Please refer to the system of your country to set the SOUND SYSTEM before you take AUTO SEARCH
or MANUAL SEARCH.
AUTO SEARCH
1) Press the <Menu> button to enter the main menu.
2) Press the <VOL+> or <VOL-> button to select the item CHANNEL.
3) Press the <CH+> or <CH-> button to select AUTO SEARCH.
4) Press the < VOL+> button to start auto searching.
CHANNEL
CHANNEL NUM
SOUND SYSTEM
AUTO SEARCH
MANUAL SEARCH
FINE TUNE
SKIP
CHANNEL EDIT
MANUAL SEARCH
1) Press the <Menu> button to enter the main menu.
2) Press the <VOL+> or <VOL-> button to select the item CHANNEL.
3) Press the <CH+> or <CH-> button to select MANUAL SEARCH.
4) Press the <VOL+> or <VOL-> button to start searching.
FINE TUNE
1) Press the <Menu> button to enter the main menu.
2) Press the <VOL+> or <VOL-> button to select the item CHANNEL.
3) Press the <CH+> or <CH-> button to select FINE TUNE.
4) Press the <VOL+> or <VOL-> button to start searching.
SKIP
1) Press the <Menu> button to enter the main menu.
2) Press the < button to select the item CHANNEL.
3) Press the < button to select SKIP.
4) Press the < button to skip or un-skip the present channel.
VOL+> or <VOL->
CH+> or <CH->
VOL+> or <VOL->
NOTE: The 'skipped' channels cannot be accessed by .
If you want to access digit button,
and the
'skipped' channels will be appeared.
CH+> or <CH->
<
'skipped' channels ,please input the channel number by
CHANNEL EDIT
1) Press the <Menu> button to enter the main menu.
2) Press the <VOL+> or <VOL-> button to select the item CHANNEL.
3) Press the <CH+> or <CH-> button to select CHANNEL EDIT.
4) Press the <VOL+> button to enter CHANNEL EDIT.
5) Press the <Menu> button to go back to the previous level.
-10 -
Using the TV features
Using the PICTURE menu
PROGRAM
Adjust picture settings
1) Press the <Menu> button to enter the main menu.
2) Press the < button to select the item
VOL+> or< VOL->
PICTURE PARAMETERS.
3) Press the < button to select the item you
CH+> or< CH->
want to adjust.
4) Press the < button to adjust the level.
VOL+> or <VOL->
5) Press the <Menu> button to go back to the previous level.
The adjusted data is memorized automatically in the user mode.
PROGRAM
Setting Colour Temperature
1)Press the <CH+> or <CH-> button to select the item COLOUR TEMP ,
2)Press the <VOL+> button enter next level. There are five modes in COLOUR TEMP item.
3)Press <CH+> or <CH-> to select your wishful item ,and then Press <VOL+>or<VOL-> to ensure.
4)Press the <Menu> button to go back to the previous level.
.
Using the AUDIO SETTING menu
PICTURE PARAMETERS
BRIGHTNESS
CONTRAST
SATURATION
WARMER
NORMAL
COOLER
WARM
COOL
Adjust audio settings
AUDIO SETTING
1) Press the <Menu> button to enter the main menu.
2) Press the < button to select the item AUDIO SETTING.
3) Press the < button to select the item you want to adjust.
4) Press the < button to adjust the level.
VOL+> or <VOL->
CH+> or <CH->
VOL+> or <VOL->
The adjusted data is memorized automatically in the user mode.
Adjust BALANCE
1) Press the <Menu> button to enter the main menu.
2) Press the < button to select the item AUDIO SETTING.
3) Press the < button to select the item BALANCE.
4) Press the < button to adjust the balance between the left speaker and right speaker..
VOL+> or <VOL->
CH+> or <CH->
VOL+> or <VOL->
The adjusted data is memorized automatically ,this item is not effective on sound modes .
Setting Surround Modes
1) Press the <Menu> button to enter the main menu.
2) Press the <VOL+> or <VOL-> button to select the item AUDIO SETTING.
)Press the <CH+> or <CH-> button to select the item SURROUND ,
2
3)Press the <VOL+> button enter next level. There are three modes in SURROUND item.
4)Press <CH+> or <CH-> to select your wishful item ,and then Press <VOL+>or<VOL-> to ensure.
5)Press the <Menu> button to go back to the previous level.
.
-11 -
Using the TV features
Using the PIP menu
1)Press the <Menu> button to enter the main menu ,
2)Press the < select the PICTURE IN PICTURE.
3)Press the <
4)Press the <
5)Press
from among the OFF, PIP and PBP.
6)Press the <Menu> button to go back to the previous level.
VOL+> or <VOL->
CH+> or <CH->
VOL+>
the <CH+> or <CH-> button ,you can select one mode
button to enter the PIP SIZE,
to
button to select the PIP SIZE,
PICTURE IN PICTURE
Note:1)WhenMainpicture is TV/SCART1/SCART2/VIDEO,the Sub Picture is YPbPr/PC/DVI.
2)WhenMainpicture is YPbPr/PC/DVI,the Sub Picture is TV/ SCART1/SCART2/VIDEO.
Using the TV features
Using the GENERAL SETTINGS menu
OSD POSITION
1) Press the <Memu> button to enter the main menu.
2) Press the < button to select the item
VOL+> or <VOL->
GENERAL SETTINGS.
3) Press the < button to select OSD POSITION
CH+> or <CH->
and press <VOL+> enter it .
4) Press the < button to adjust the OSD
VOL+>or <VOL->
POSITION.
5) Press the <Menu> button to go back to the previous level.
T
he adjusted data is memorized automatically .
Color system
OSD LANGUAGE
GENERAL SETTINGS
LANGUAGE ENGLISH
OSD POSITION
COLOR SYSTEM
OSD LANGUAGE
BLANK
TRANSPARENCY
ADVANCE
CHANGE PASSWORD
BLANK
1) Press the <Menu> button to enter the main menu.
2) Press the <VOL+> or <VOL-> button to select the item GENERAL SETTINGS.
3) Press the <CH+> or <CH-> button to select BLANK.
4) Press the <VOL+>or <VOL-> button to enable the BLANK
NOTE: When you enable the blank ,the screen will turn into blank screen saver mode in case of valid input signal.
The screen will turn into auto screen saver mode several seconds later, and get into stand-by mode 15
minutes later.
TRANSPARENCY
1) Press the <Menu> button to enter the main menu.
2) Press the <VOL+> or <VOL-> button to select the item GENERAL SETTINGS
3) Press the <CH+> or <CH->button to select TRANSPARENCY
4) Press the <VOL+> or <VOL->button to adjust this ITEM.
The adjusted data is memorized automatically .
-13 -
Using the TV features
Teletext Operations
ENTER TELETEXT MODE
Select the channel that is broadcasting the desired Teletext program.
Press < Text> button on the remote control to enter the Teletext mode ,and press the same button quit the Teletext mode..
Note:1)All the operations the below should be under the Teletext mode.
2) There are some multiplex buttons on the remote control for Teletext operation.
PAGE SELECTION
You can directly input your desired page number by pressing <0>~<9> buttons.
You can sequentially read pages by pressing <CH+> or <CH-> button.
HOLD
Some Teletext information is contained on more than one page, the pages automatically changing after a given reading
time.
Press the <Hold> button to stop the page changing.
Press the <Hold> button again to allow the page to change.
REVEAL
Some Teletext pages contain quiz or questions with hidden answers.
Press the <Reveal> button to see the answers.
Press the <Reveal> button to hide the answers again.
CANCEL
When a page is selected in Teletext mode it may take some time before it becomes available.
Press the <Cancel> button to switch to the TV mode.
When the required page is found, the page number will appear at the top of the TV picture.
Press the <Cancel> button to return to the selected Teletext page.
Note: You can change TV program while in this mode
SUB CODE
Some Teletext pages contain sub page that require you to input the sub code.
Press the <Sub. Code> button till pages/sub pages is displayed, and enter four-digit sub code for the sub page
you need.
If you want to quit Sub. Code mode, press <Sub. Code> button till pages/sub pages is disappeared.
MIX
You can mix Teletext with TV pictures, which means transparent teletext.
Press the <Mix> button to get mixed effect, and press the <Mix> button again to cancel the mixed effect.
SIZE (Top/Bottom/Full)
Using SIZE to enable easier reading (larger display).
Press the <Szie> button to display the TOP HALF of the page.
Press this button once more to display the BOTTOM HALF of the page.
Press again to return to a FULL PAGE display.
Note: Changing pages reverts to a FULL PAGE display.
INDEX
Teletext index page guides you quickly to your desired page.
Press the <Index> button to jump to the index page.
TIME
Time information is contained in the teletext broadcast.
Press the <Time >button to display the time.
FAST TEXT
The RED, GREEN, YELLOW & BLIE buttons are used for quick access to colour coded pages transmitted by
FAST TEXT broadcast.
-14-
Appendix
Scart connector
See Signal Source Selection on page 8 for selecting SCART input.
Appendix
Troubleshooting
Before calling a service technician, please check the following table for a possible cause of the problem and
some solutions.
Symptoms
TV will not turn on
No picture, no sound
No sound, picture OK
Poor sound, picture OK
Poor picture, sound OK
Unable to select a certain channel
Possible Solutions
Make sure the power cord is plugged in, then press <Power>.
The remote control batteries may be dead. Replace the batteries.
Check if you have set the off timer.
Check the antenna/cable connections.
Press [Display] to see if you have select the right signal source.
The sound may be muted. Press < on the remote control or .
The station may have broadcast difficulties. Try another channel.
Check the speakers cable connections.
The station may have broadcast difficulties. Try another channel
Check the speakers cable connections.
Check the antenna connections.
The station may have broadcast difficulties. Try another channel.
Adjust the picture from the menu.
The channel may be skipped.
VOL+>
Poor colour or no colour
The remote control does not operate
Disorder display at power on
The station may have broadcast difficulties. Try another channel.
There may be an obstruction between the remote control and the
remote control sensor.
The batteries may be installed with a wrong polarity.
The remote control batteries may be dead. Replace the batteries.
Check if you have entered Teletext mode. Press <Text> to quit.
This may be caused by too short interval between power off and on.
Unplug the power and restart.
Cleaning and care
WARNING: Do not try to remove the cabinet back. Refer servicing to qualified service technicians.
To clean the TV screen:
1) Unplug the TV to avoid possible shock hazard.
2) Use a clean cellulose sponge or chamois cloth dampened with a solution of mild detergent and warm
water to clean the TV screen and trim. Do not use too much water as water spilled into the cabinet
can cause damage to the TV.
3) Wipe off any excess moisture with a clean dry cloth.
4) Polish the cabinet with a quality furniture polish to maintain the finish and appearance of the cabinet.
Caution: Never use strong solvents such as thinner, benzene, or other chemicals on or near the cabinet.
These chemicals can damage the finish of the cabinet.
-16 -
Specifications
Diagonal display size
Television system
Channel coverage
Resolution
Contrast
Brightness
Viewing angles
Power source
Power consumption
Audio output
Connection interface
50 INCHES PDP
Multi- standard(PAL,SECAM)
VHF-L: E2-S8
VHF-H: S9-S37
UHF: S38-E69
1366X768
2500:1
1000cd/m
oo
170 (H)/170 (V)
2
AC100V--240V, 50/60Hz
500W
7W+7W
RF input: Cable/ Antenna 1
VIDEO input: VIDEO
1
RF
YPbPr/YCbCr 1
GRAPHIC input: Analog RGB 15pin 1
Digital RGB(DVI-D) X1
SCART INPUT: SCART1 (CVBS/RGB)
SCART2 (Y-C)
AUDIO input: AV Audio 1
Mini-jack for Stereo
AUDIO output: AV Audio
1
(3.5 )X1
SCART Audio X 2
Mini-jack for Stereo
(3.5 )X1
OTHER: RS232C X 1 (for software updateing)
Dimensions
Weight
Supplied accessories
41inches X 25inches X 3inches
54.6Kg
Remote control, Power cord
Design and specifications are subject to change without notice.
-17 -
Loading...