Hilti TE DRS-S User Manual
TE DRSS
English
Printed: 09.08.2017 | Doc-Nr: PUB / 5135213 / 000 / 01
Printed: 09.08.2017 | Doc-Nr: PUB / 5135213 / 000 / 01
English 1
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free
handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of symbols used
1.2.1 Warnings
Warnings alert persons to hazards that may occur when handling or using the product. The following signal
words are used in combination with a symbol:
DANGER! Draws attention to an imminent hazard that will lead to serious personal injury or
fatality.
WARNING! Draws attention to a potential hazard that could lead to serious personal injury or
fatality.
CAUTION! Draws attention to a potentially dangerous situation that could lead to minor personal
injury or material damage.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
Read the operating instructions before use
Instructions for use and other useful information
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions.
The numbering reflects the sequence of operations shown in the illustrations and may deviate
from the steps described in the text.
Item reference numbers are used in the overview illustration and refer to the numbers used in
the key in the product overview section.
This symbol is intended to draw special attention to certain points when handling the product.
1.3 Product information
Hilti products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained
personnel or if used not in accordance with the intended use.
The type designation and serial number are stated on the rating plate.
▶ Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Dust removal module TE DRSS
Generation 01
Serial no.
Printed: 09.08.2017 | Doc-Nr: PUB / 5135213 / 000 / 01
2 English
2 Safety
2.1 Safety instructions
▶ The user and persons in the vicinity must wear suitable protective goggles, a hard hat, protective gloves
and protective footwear while the device is in use.
▶ Wear your personal protective equipment and always wear protective glasses. Depending on the type of
power tool you are using and its purpose, wearing safety equipment such as a dust mask, slip-resistant
safety shoes, a hard hat or hearing protection will reduce the risk of injury.
▶ If devices for dust extraction and collection can be connected, make sure these are connected and used
correctly. The use of a dust extraction system can reduce dust-related hazards.
▶ Do not drill or chisel on hazardous materials (e.g. asbestos).
▶ Before beginning the work, check the hazard classification of the dust that will be produced.
▶ Make sure that the working area is well lit and well ventilated.
▶ Contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases among
operators or bystanders.
▶ Stay alert, watch what you are doing and use common sense when working.
▶ Wear suitable work clothes.
▶ Use the product only within its specified limits.
▶ To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables.
▶ Use an antistatic suction hose in order to avoid electrostatic effects.
Printed: 09.08.2017 | Doc-Nr: PUB / 5135213 / 000 / 01
English 3
3 Description
3.1 Overview of the product
Printed: 09.08.2017 | Doc-Nr: PUB / 5135213 / 000 / 01
Loading...